Anda di halaman 1dari 6

320D2 Excavators MDJ00001-UP (MACHINE)... https://172.33.0.222/sisweb/sisweb/techdoc/t...

Shutdown SIS

Previous Screen

Product: EXCAVATOR
Model: 320D2 EXCAVATOR MDJ
Configuration: 320D2 Excavators MDJ00001-UP (MACHINE) POWERED BY
C7.1 Engine

Operation and Maintenance Manual


320D2 Excavator
Media Number -SEBU9247-08 Publication Date -01/09/2015 Date Updated -24/08/2018

i07501867

Maintenance Interval Schedule


SMCS - 7000

1 of 6 16/03/2019, 09:14
320D2 Excavators MDJ00001-UP (MACHINE)... https://172.33.0.222/sisweb/sisweb/techdoc/t...

Ensure that all safety information, warnings, and instructions are read and
understood before any operation or any maintenance procedures are
performed.

The user is responsible for the performance of maintenance. All


adjustments, the use of proper lubricants, fluids, filters, and the
replacement of components due to normal wear and aging are included.
Failure to adhere to proper maintenance intervals and procedures may
result in diminished performance of the product and/or accelerated wear of
components.

Use mileage, fuel consumption, service hours, or calendar time, WHICH


EVER OCCURS FIRST, in order to determine the maintenance intervals.
Products that operate in severe operating conditions may require more
frequent maintenance. Refer to the maintenance procedure for any other
exceptions that may change the maintenance intervals.

Note: Before each consecutive interval is performed, all maintenance from


the previous interval must be performed.

Note: If Cat HYDO Advanced hydraulic oils are used, the hydraulic oil
change interval is extended to 6000 hours. S·O·S services after 3000 hours
is strongly recommended. Consult your Cat dealer for details.

When Required

Air Conditioner/Cab Heater Filter (Recirculation) - Inspect/Replace


Battery - Recycle
Battery or Battery Cable - Inspect/Replace
Bucket Linkage - Inspect/Adjust
Bucket Tips - Inspect/Replace
Bucket Tips - Inspect/Replace
Cab Air Filter (Fresh Air) - Clean/Replace
Camera - Clean/Adjust
Circuit Breakers - Reset
Engine Air Filter Primary Element - Clean/Replace
Engine Air Filter Secondary Element - Replace
Film (Product Identification) - Clean
Fuel System - Prime
Fuses - Replace
High Intensity Discharge Lamp (HID) - Replace
Oil Filter - Inspect
Radiator Core - Clean
Track Adjustment - Adjust

2 of 6 16/03/2019, 09:14
320D2 Excavators MDJ00001-UP (MACHINE)... https://172.33.0.222/sisweb/sisweb/techdoc/t...

Window Washer Reservoir - Fill


Window Wiper - Inspect/Replace
Windows - Clean

Every 10 Service Hours or Daily for First 100 Hours

Boom and Stick Linkage - Lubricate


Bucket Linkage - Lubricate

Every 10 Service Hours or Daily

Cooling System Coolant Level - Check


Engine Oil Level - Check
Fuel Filter Change Indicator - Inspect
Fuel System Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Hydraulic System Oil Level - Check
Indicators and Gauges - Test
Seat Belt - Inspect
Track Adjustment - Inspect
Travel Alarm - Test
Undercarriage - Check

Every 10 Service Hours or Daily for Machines Used in


Severe Applications

Bucket Linkage - Lubricate

Every 50 Service Hours or Weekly

Quick Coupler - Lubricate

Every 100 Service Hours or 2 Weeks

Bucket Linkage - Lubricate

Every 100 Service Hours or 2 Weeks for Machines Used


in Severe Applications

Boom and Stick Linkage - Lubricate

Every 100 Service Hours of Continuous Hammer Use

3 of 6 16/03/2019, 09:14
320D2 Excavators MDJ00001-UP (MACHINE)... https://172.33.0.222/sisweb/sisweb/techdoc/t...

Oil Filter (Hydraulic Hammer) - Replace

Initial 250 Service Hours

Engine Valve Lash - Check


Final Drive Oil - Change
Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace
Hydraulic System Oil Filter (Return) - Replace
Swing Drive Oil - Change

Every 250 Service Hours

Engine Oil Sample - Obtain


Final Drive Oil Sample - Obtain

Every 250 Service Hours or Monthly

Belt - Inspect/Adjust/Replace
Condenser (Refrigerant) - Clean
Final Drive Oil Level - Check
Swing Bearing - Lubricate
Swing Drive Oil Level - Check

Every 250 Service Hours of Partial Hammer Use (50% of


Service Hours)

Hydraulic System Oil Filter (Case Drain) - Replace


Hydraulic System Oil Filter (Pilot) - Replace
Oil Filter (Hydraulic Hammer) - Replace

Every 250 Service Hours of Continuous Hammer Use

Hydraulic System Oil Filter (Case Drain) - Replace


Hydraulic System Oil Filter (Pilot) - Replace

Initial 500 Hours (for New Systems, Refilled Systems,


and Converted Systems)

Cooling System Coolant Sample (Level 2) - Obtain

Every 500 Service Hours

4 of 6 16/03/2019, 09:14
320D2 Excavators MDJ00001-UP (MACHINE)... https://172.33.0.222/sisweb/sisweb/techdoc/t...

Cooling System Coolant Sample (Level 1) - Obtain


Hydraulic System Oil Sample - Obtain
Swing Drive Oil Sample - Obtain

Every 500 Service Hours or 3 Months

Boom and Stick Linkage - Lubricate


Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap and Strainer - Clean

Every 500 Service Hours of Partial Hammer Use (50% of


Service Hours)

Hydraulic System Oil Filter (Case Drain) - Replace


Hydraulic System Oil Filter (Pilot) - Replace

Every 600 Service Hours of Continuous Hammer Use

Hydraulic System Oil - Change


Hydraulic System Oil Filter (Return) - Replace

Every 1000 Service Hours or 6 Months

Battery - Clean
Battery Electrolyte Level - Check
Battery Hold-Down - Tighten
Engine Valve Lash - Check
Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace
Swing Drive Oil - Change

Every 1000 Service Hours of Partial Hammer Use (50% of


Service Hours)

Hydraulic System Oil - Change


Hydraulic System Oil Filter (Return) - Replace

Every 2000 Service Hours or 1 Year

Final Drive Oil - Change


Hydraulic System Oil Filter (Return) - Replace

5 of 6 16/03/2019, 09:14
320D2 Excavators MDJ00001-UP (MACHINE)... https://172.33.0.222/sisweb/sisweb/techdoc/t...

Receiver Dryer (Refrigerant) - Replace


Swing Gear - Lubricate

Every Year

Cooling System Coolant Sample (Level 2) - Obtain

Every 3 Years After Date of Installation or Every 5 Years


After Date of Manufacture

Seat Belt - Replace

Every 6000 Service Hours or 3 Years

Cooling System Coolant Extender (ELC) - Add


Hydraulic System Oil - Change

Every 12 000 Service Hours or 6 Years

Cooling System Coolant (ELC) - Change

Copyright 1993 - 2019 Caterpillar Inc.


  Sat Mar 16 2019 09:10:55 GMT+0800 (Central Indonesia Time)
All Rights Reserved.
Private Network For SIS Licensees.

6 of 6 16/03/2019, 09:14

Anda mungkin juga menyukai