Anda di halaman 1dari 6

www.hilti.in Profis Anchor 2.8.

0
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 28-03-2019
E-Mail:

Specifier's comments:

1 Input data
Anchor type and diameter: HIT-HY 200 + HIT-V-R M12
Seismic/Filling set or any suitable annular gap filling solution
Effective embedment depth: hef,opti = 141 mm (hef,limit = 240 mm)
Material: A4
Evaluation Service Report: ETA 12/0084
Issued I Valid: 28-07-2017 | -
Proof: SOFA design method + fib (07/2011) - after ETAG BOND testing
Stand-off installation: eb = 0 mm (no stand-off); t = 8 mm
Anchor plate: lx x ly x t = 190 mm x 150 mm x 8 mm; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, , fc,cyl = 28.60 N/mm2; h = 350 mm, Temp. short/long: 40/24 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
Reinforcement to control splitting according to

fib (07/2011), 16.1.5 present

R
- The anchor calculation is based on a rigid baseplate assumption.

Geometry [mm] & Loading [kN, kNm]

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 28-03-2019
E-Mail:

2 Load case/Resulting anchor forces y


Load case: Design loads

Anchor reactions [kN] 3 4


Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
1 5.795 4.008 4.008 0.000
2 0.949 4.008 4.008 0.000 x
Tension Compression
3 5.795 4.008 4.008 0.000
4 0.949 4.008 4.008 0.000

max. concrete compressive strain: 0.10 [‰] 1 2


max. concrete compressive stress: 3.10 [N/mm2]
resulting tension force in (x/y)=(-32/0): 13.488 [kN]
resulting compression force in (x/y)=(84/0): 7.528 [kN]

Anchor forces are calculated based on the assumption of a rigid baseplate.

3 Tension load SOFA (fib (07/2011), section 16.2.1)


Load [kN] Capacity [kN] Utilization bN [%] Status
Steel Strength* 5.795 31.551 19 OK
Combined pullout-concrete cone failure** 13.488 22.928 59 OK
Concrete Breakout Strength** 13.488 23.701 57 OK
Splitting failure** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (anchors in tension)

3.1 Steel Strength


NRk,s [kN] gM,s NRd,s [kN] NSd [kN]
59.000 1.870 31.551 5.795

3.2 Combined pullout-concrete cone failure


Ap,N [mm2] A0p,N [mm2] y A,Np
2
t Rk,ucr,25 [N/mm ] scr,Np [mm] ccr,Np [mm] cmin [mm]
1,17,952 1,38,240 0.853 18.00 372 186 80
2 0
yc t Rk,cr [N/mm ] max t Rk,cr [N/mm2] y g,Np y g,Np
1.038 8.82 12.97 1.439 1.217
ec1,N [mm] y ec1,Np ec2,N [mm] y ec2,Np y s,Np y re,Np
32 0.852 0 1.000 0.829 1.000
N0Rk,p [kN] NRk,p [kN] gM,p NRd,p [kN] NSd [kN]
46.886 34.391 1.500 22.928 13.488

3.3 Concrete Breakout Strength


Ac,N [mm2] A0c,N [mm2] y A,N ccr,N [mm] scr,N [mm]
1,30,750 1,78,929 0.731 212 423
ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N
32 0.867 0 1.000 0.813 1.000
k1 N0Rk,c [kN] gM,c NRd,c [kN] NSd [kN]
7.700 68.949 1.500 23.701 13.488

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 28-03-2019
E-Mail:

4 Shear load SOFA (fib (07/2011), section 16.2.2)


Load [kN] Capacity [kN] Utilization bV [%] Status
Steel Strength (without lever arm)* 4.008 19.231 21 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength** 16.030 53.830 30 OK
Concrete edge failure in direction x+** 8.015 11.990 67 OK
* anchor having the highest loading **anchor group (relevant anchors)

4.1 Steel Strength (without lever arm)


VRk,s [kN] gM,s VRd,s [kN] VSd [kN]
30.000 1.560 19.231 4.008

4.2 Pryout Strength (Bond Strength controls)


Ap,N [mm2] A0p,N [mm2] y A,Np
2
t Rk,ucr,25 [N/mm ] ccr,Np [mm] scr,Np [mm] cmin [mm]
1,17,952 1,38,240 0.731 18.00 186 372 80
2 0
yc t Rk,cr [N/mm ] max t Rk,cr [N/mm2] y g,Np y g,Np k4
1.038 8.82 12.97 1.439 1.217 2.000
ec1,V [mm] y ec1,Np ec2,V [mm] y ec2,Np y s,Np y re,Np
0 1.000 0 1.000 0.829 1.000
N0Rk,p [kN] NRk,p [kN] gM,c,p VRd,cp [kN] VSd [kN]
46.886 40.373 1.500 53.830 16.030

4.3 Concrete edge failure in direction x+


lf [mm] dnom [mm] kV a b
141 12.0 1.700 0.133 0.068
c1 [mm] Ac,V [mm2] A0c,V [mm2] y A,V
80 40,800 28,800 1.417
y s,V y h,V y a,V ec,V [mm] y ec,V y re,V y 90°,V
1.000 1.000 1.000 0 1.000 1.000 2.000
V0Rk,c [kN] gM,c VRd,c [kN] VSd [kN]
12.695 1.500 11.990 8.015

5 Combined tension and shear loads SOFA (fib (07/2011), section 10.3)
bN bV a Utilization bN,V [%] Status
steel 0.184 0.208 2.000 8 OK
concrete 0.588 0.668 1.500 100 OK

baN + baV <= 1

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 28-03-2019
E-Mail:

6 Displacements (highest loaded anchor)


Short term loading:
NSk = 0.703 [kN] dN = 0.009 [mm]
VSk = 5.937 [kN] dV = 0.297 [mm]
dNV = 0.297 [mm]
Long term loading:
NSk = 0.703 [kN] dN = 0.021 [mm]
VSk = 5.937 [kN] dV = 0.475 [mm]
dNV = 0.475 [mm]

Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!

The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!

7 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid base plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility! 
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• Bore hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice,
blow twice with oil-free compressed air (min. 6 bar)).
• Characteristic bond resistances depend on short- and long-term temperatures.
• Please contact Hilti to check feasibility of HIT-V rod supply.
• The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by
filling the gap with mortar of sufficient compressive strength (e.g. by using the HILTI Seismic/Filling set) or by other suitable means
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• Checking the transfer of loads into the base material is required in accordance with fib (07/2011)!

Fastening meets the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 28-03-2019
E-Mail:

8 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200 + HIT-V-R M12
Profile: no profile Installation torque: 0.040 kNm
Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 14 mm
Plate thickness (input): 8 mm Hole depth in the base material: 141 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 171 mm
Drilling method: Hammer drilled
Cleaning: Compressed air cleaning of the drilled hole according to instructions for use is required

8.1 Recommended accessories

Drilling Cleaning Setting


• Suitable Rotary Hammer • Compressed air with required • Dispenser including cassette and mixer
• Properly sized drill bit accessories to blow from the bottom of • Seismic/Filling set
the hole • Torque wrench
• Proper diameter wire brush
y

95 95

25
3 4

75
100

x
75

1 2
25

50 90 50

Coordinates Anchor [mm]


Anchor x y c-x c+x c-y c+y
1 -45 -50 80 170 - -
2 45 -50 170 80 - -
3 -45 50 80 170 - -
4 45 50 170 80 - -

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 28-03-2019
E-Mail:

9 Remarks; Your Cooperation Duties


• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas
and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be
strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted
prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the
data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be
put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly
with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an
aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or
suitability for a specific application.
• You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do
not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software
in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or
damaged data or programs, arising from a culpable breach of duty by you.

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan

Anda mungkin juga menyukai