Thank you for choosing Analog Way and the Pulse². By following these simple steps, you will be able to set up
and use your powerful Dual Scaler Hi-Resolution Seamless Switcher based on Analog Way’s Midra™ platform
within minutes. Discover the Pulse² capabilities and intuitive interface while configuring your first show and
unleash your creativity for a new experience in show and event management.
CAUTION!
WHAT’S IN THE BOX If required, front handles of the device can be dismantled,
• 1 x Pulse² (PLS350) but with caution. The original screws removed must not
• 1 x Power supply cord be reintroduced to their location without handles in place.
Substantial damages can occur, including risk of electric
• 1 x Ethernet cross cable (for device update) shock from the mains voltage. Only M4x12mm screws can
• 1 x Remote Control Software (RCS²)* be used. (They are supplied with the unit.)
• 1 x Set of 6 audio 5-pin screw terminals
• 1 x Front Rack Ears (the parts are stowed in the packaging foam)
• 1 x User Manual (PDF)*
Go on our website to register
• 1 x Quick Start guide* your product(s) and be notified
* User manual, quick start guide and the RCS² are available about new firmware versions:
http://bit.ly/AW-Register
on www.analogway.com
QUICK INSTALL AND SETUP
Getting started:
You may wish to reset the unit to factory settings to get 4. To display a PIP, select the LAYER B (it will begin to blink)
started. Go to: Menu > Control > Reset/Erase > Default then select your source (it will also blink). Press TAKE to
Values > Yes display the layer on the Program output.
To see the layer beneath, you will need to clear or move the
1. Select the Output resolution that matches the native
layers that are above.
resolution of your display. You will next be able to choose
the output rate. 5. To clear the layer or any other layer, select the layer (it
Menu > Output > Output format > 1920x1080 > will blink) then, select BLACK. Press TAKE to remove the
Internal Ref > 60 Hz layer from the Program output.
2. Inputs can be configured automatically using the Auto TIP: If you want the Program and Preview to toggle/flipflop
Set All function. Menu > Inputs > AutoSet All > Yes during each Take, enable this feature by going to Menu >
It will scan each input and detect the sync type that is Control > Functions > Preset Toggle.
plugged in. You can still do an Autoset or manual setup per Once enabled, the old Program output will become the
input. new Preview after each Take.
The Pulse² has 6 layers available called: FRAME, LAYERS 6. To record and display a Quick Frame follow the steps on
A & B, LOGOS 1 & 2 and a QUICK FRAME. Each layer will page 4.
obscure your view other layers below. See the next page which describes the button lighting color
code and other front panel features.
3. To display a source, select the LAYER A (it will begin to
blink) then, select a source (it will also blink). Press TAKE Pulse² can be used to display:
to transition your source from Preview to Program output. - sources seamlessly switched in the LAYER A. (Only 1 layer)
- 1 layer and 1 Logo over the LAYER A.
There will always be a layer selected (blinking) and a source
- 2 layer and 1 Logo over a Frame by resizing the LAYER A.
selected (blinking) to the selected layer (blinking). To view
on Preview or change the contents of a different layer, IMPORTANT: Simply selecting a menu item will not set it
simply select it. Only 1 layer can be seen on the Preview to that value. Be sure to press the ENTER button when
at once. setting the menu items.
PULSE² - REF. PLS350 / FRONT & REAR PANELS DESCRIPTION
Layer: Matrix mode:
Front panel display: Menu scroll Black: clear the layer
4-line VFD #1 to #2: select the output
knob Layer selection: Freeze: freeze the input #1-2, a layer and a source,
Frame: non-scaled layer linked to the current then press TAKE
Logo 1/2: display or change logo layer on Program
Layer A/B: scaled layers
Input selection:
1 to 4: access source 1 to 4, Shortcut: TAKE:
Control: display Frame/Logo 1 to 4 Effect: shortcut to transition menu Transition the pre-
Exit/Menu: Home menu HDMI 1/2: access HDMI 1 or HDMI 2, Preset: recall a custom stored preset selected sources onto the
or back one level display Frame/Logo 5 to 6 Split Screen: load a split screen preset Program output with the
Enter: validate the menu SDI 1 to SDI 2: access SDI 1 to SDI 2, Swap: exchange sources between selected effects
or command display Frame/Logo 7 to 8 layer A and layer B
Universal Analog
Computer TV/HDTV:
outputs #1 to #2
NOTE: To adjust layer Size or Pos, use the Layer Menus. To adjust
Layer/source selected or is not currently Blanking, use the Auto Centering or Blanking adjustments in the
Blinking green:
active on the Program output Image menu.
3- Adjust the layer with ADJUSTMENT button (Pos & Size tings, amongst other user oriented functions (see next page) BALANCED
or Zoom) Inputs # 1 & #2: DVI embedded audio HDMI
4- Select a transition (open/close) or an effect into Layer Inputs #3 & #4: DVI and HDMI embedded audio HDMI
menu [Home menu] Inputs SPDIF #1 and #2: digital audio inputs
5- Press TAKE to view the result on the main screen Inputs HDMI #1 and #2: embedded audio HDMI
6- To remove layer, press BLACK then TAKE Inputs SDI #1 to #2: embedded audio SDI
7- For another layer setup, repeat from step #1
Outputs #1 and #2: balanced & unbalanced connection
Outputs SPDIF #1 and #2: digital audio outputs
Outputs #1 and #2: Embedded audio HDMI (over DVI connectors)
HOW TO DO AN AUTOTAKE?
HOME MENU (extract)
The Autotake function performs a TAKE automatically each time an input is selected.
LOGOS/FRAME RECORD FRAMES FRAME #1 TO #8 The [Empty] term appears next to all unused slots
QUICK FRAME: full and individual frame that can be displayed on top of every layer.
It is possible to store up to 8 frames in the device non volatile memory.
- Select RECORD FRAMES in the frames menu.
- A white rectangle will appear on your Program display, indicating the frame which will be caught and saved. (The Frame can be
captured in Preview too.)
- To select the Quick frame, please go into the SCREEN menu, select QUICK FRAME menu and then choose a Frame slot. The
selected frame will be your QUICK FRAME.
Now to display it, simply press the front panel button QUICK FRAME. It becomes solid RED.
- To remove the QUICK FRAME, press the QUICK FRAME button on the front panel. It becomes solid green.
TIP: a long press on the BLACK button will clear all layers on Preview. Press TAKE to view your Program display turn to black.
OUTPUT #1
HDCP DETECTION DISABLED
OUTPUT #2
AUTOMATIC
The HDCP Encryption can be disabled on HDMI/DVI inputs or/and Output #1/Output #2. This can be useful when you have a
computer which is detecting the HDCP compliance of your switcher and protecting the content by encrypting the signal from this
computer. This feature will disable the HDCP compliance on this specific HDMI/DVI input only.
If you want to use HDCP content from your sources, be sure to use only HDCP compliant screens or projector. If it’s not the case,
the output image could be disabled.
Screen will go to black without displaying the HDCP input image, or partially layer out on HDCP content.
The output status can provide you all information about the output in real time. This feature is particularly useful when HDCP is
used with long cable to be sure the communication is well handled.