Theory
Theory
1. Which of the following is made by gluing three or more veneers together? A) composite
board b) plywood c) chip board d) particle board
2. Which of the following is a natural defect? A) knot b) bow c) twist d) check
3. Popular methods of wood conversion includes . A) plain sawn b) circular sawn c) regular
sawn d) natural sawn
4. The wood defect caused by the offshoot of a branch at the lowest stem is called? A) knot b)
shake c) twist d) decay
5. The growth in trees take place around the? A) heart wood b) medullary rays c) sapwood c)
bud at the tip of the tree
6. The product formed when the impurity is removed from iron ore in a blast furnace is called?
A) steel b) slag c) pig iron d) cast iron
7. Which of the following is an iron processing material? A) coke b) dross c) scraps d) slang
8. The metal that can be produced when copper is alloyed with zinc is called? A) bronze b)
brass c) solder d) aluminium
9. Which of the following materials is needed in iron productivity? A) cast iron b) iron ore c) pig
iron d) white iron
10. Which of the following has carbon content ranging between 0.6% and 1.3% a) low carbon
steel b) high carbon steel c) medium carbon steel d) mild steel
11. The following are methods of processing plastics EXCEPT a) calendaring b) compression c)
reverberating d) injection
12. Which of the following is not a ceramic product? A) flower vase b) pot c) bucket d) tiles
13. One of the following is from rubber a) bulb b) balloon c) chair d) book
14. Ceramics products are best dried in a compartment called...... a) kiln b) dryer c) Sun d) stove
15. What type of plastics can be remoulded? A) thermoplastics b) vitaplastics c) thermometer d)
thermoset
Theory
1. i. List two other materials added to the blast furnace and their uses.
ii. Write 5 advantages of laminated boards
2. I. Write 2 disadvantage of laminated boards?
ii. List two purpose of pounding clay.
3. i. What is an alloy metal?
Ii State 3 properties of ceramics.
4. List 4 methods of processing plastics.
List 2 methods of making metals
Theory
1. i. Divide 100 mm line into 7 equal parts. , show all construction details.
ii. Fully classify pencils.
2. I. Construct an isosceles triangle of vertical height 85 mm, and vertical angle 30°.
Ii fully classify paper formats with their respective dimensions.
3. Construct a triangle of perimeter 130 mm, base side 40mm and a base angle 105°, and
state the second base angle.
Theory
5. The dimension of A6 paper format is ? A) 1188 × 75 b) 210 × 148 c) 148 × 105 d) not listed
6. The inclined side in oblique projection is drawn to ? A) full length b) half full length c) quarter
full length d) one third full length
7. A site plan shows the? A) Location of building b) Building foundation c) Elevation of a building
d) Cross section of a building
8. Which of the following workshop tools is used for finding the diameter of a round ball? A)
protractor b) Try square c) Odd leg caliper d) Micrometer
10. Which of these scales is the largest? A) 1:5 b) 1:25 c) 1:45 d) 1:65
11. To draw an escribed circle of a given triangle, the first step is to? A) Bisect one side b) Bisect one
interior angle c) Draw perpendicular bisector d) Extend one side
12. The similarity between a deltoid and a rhombus is that? A) both are parrallelogram b) their
angles are all right angles c) all their sides are equal d) their diagonal bisect at right angles
13. Which of these is continuous irregular line used for? A) hidden outlines b) visible outlines c)
cutting planes d) sections
14. Which of these is part of a triangle? A) vertex b) weight c) gravity center d) axis
15. If the exterior angle of a polygon is 36°, the polygon is? A) A Decagon b) An octagon c) A
hexagon d) A Pentagon
16. In which of the following is the principle of archimedean spiral employed in its construction? A)
woodruff key b) Screw thread c) Car head lamp c) Hair spring of a wrist watch
17. Which of these statement describes a concentric circle? A) any set of circle b) circle aligned by a
chord c) Circles with similar diameter d) circle that share the same center
18. Which of these is true of a reflex angle? A) angle greater than 90° but less than 180° b) angle
less than 90° c) angle greater than 180° d) angle equal to 180°
20. The dimensions of DIN A2 paper is? A) 840 × 420 b) 420 x 297 c) 594 x 420 d) 840 x 594
22. The primary unit of measurement for technical drawing is? A) Millimeter b) Centimeter c) Meter
d) Kilometer
23. If a tool length of 1000 cm is represented by 200 mm on a drawing, what is the ratio of the scale
used? A) 1:100 b) 100:1 c) 1:50 d) 50:1
24. The following are drawing materials except? A) Rapidograph b) Eraser c) Razor d) Pencil
25. One of the styles of writing used in lettering is? A) Vertical b) Cartography c) Slanting d) Acrylic
26. Short dashes thin lines are used for? A) Centre lines b) hidden outlines and edges c) dimension
d) corner lines
27. Continuous thin lines are used for? A) cutting planes b) hatching c) Dimension d) centre lines
28. Centre lines can be represented by .....? A) Thin chain lines b) Thin continuous lines c) Thin short
dashes d) Thick continuous lines
32. The true shape of a conic section parallel to the slant side is? A) parabola b) circle c) ellipse d)
hyperbola
33. The true shape of a conic section inclined to the axis and cutting both sides is? A) parabola b)
circle c) ellipse d) hyperbola
34. The true shape of a conic section at right angles to the axis is? A) parabola b) circle c) ellipse d)
hyperbola
35. The first step to construct ellipse by concentric circle method is? A) Draw the axes b) draw the
circles c) draw the arc d) not listed
Theory