Anda di halaman 1dari 2

C E - S E R I E S

CE 2000

T
he CE-Series of Crown amplifiers Features
are professional tools designed and
built for professional use. Engineered • Accurate, uncolored sound with very low dis- • Switchable input sensitivity.
and manufactured by the same teams who tortion for the best in music and voice repro- • Proportional speed fan optimizes cooling effi-
built Crown’s acclaimed Macro-Tech® and K- duction. ciency.
Series amps, the CE 2000 has the rugged • Bridge-mono/stereo mode switch allows you • Shallow rack depth. Only 12.25 inches deep!
heart and soul that have characterized to set up your amps/speakers in the configu-
Crown’s amplifiers for over 30 years. ration that best suits your needs. • Choice of Speakon®, binding post, or barrier
strip outputs (Speakon® comes standard).
With many of the same controls and features • Advanced protection circuitry guards against:
you’ve come to expect from Crown, CE- shorted outputs, open circuits, DC, mis- • Choice of balanced 1/4-inch (6.35-mm), XLR,
Series amplifiers feature front-panel detented matched loads, general overheating, high- or barrier strip inputs.
level controls, useful function indicators, frequency overloads and internal faults. • The best Three-Year, No-Fault, Fully Transfer-
proportional fan-assisted cooling, short- able Warranty in the business! It even covers
• Extremely versatile, handling a wide range
circuit protection and more. round-trip ground shipping in the U.S. for all
of speaker impedances and outputs.
For superior flexibility, Crown CE-Series warranty work.
amplfiers can work with a range of Crown
SST (System Solution Topologies) modules
which provide true professional features like Load Impedance: Safe with all types of Common Mode Rejection (CMR): Greater
fixed-point crossover and summed bass loads. Rated for 2, 4 and 8 ohms in Stereo than 70 dB from 20 Hz to 1 kHz.
output. mode, 4 and 8 ohms in Bridge-Mono mode. DC Output Offset (Shorted Input): ±10 mV.
With a powerful, reliable performance, CE- Voltage Gain to 1-kHz, 8-ohm rated output: Controls and Connectors
Series amps easily handle real 2-ohm loads 32.1-dB gain at 1.4-volt sensitivity;
26-dB gain at 2.83-volt sensitivity. Level: A detented rotary level control for each
and are capable of chest-thumping lows. channel located on the front panel.
Plus, your investment in an CE-Series ampli- Required AC Mains: 50/60 Hz (North Ameri-
fier is backed by Crown’s unequaled Three- can units are 60 Hz only); 100-, 120- and Power: An on/off rocker switch located on the
Year, No-Fault, Fully Transferable Warranty 230-/240-VAC (±10%) units are available. front panel.
that covers everything. Mode: A two-position switch located on the
AC Line Current,
For more details about the Crown CE-Series, 100 Volts: 11.4 A; back panel below the input connectors which,
contact the Crown Technical Support Group 120 Volts: 9.5 A; when turned to stereo, operates the amplifier
at 800-342-6939 or 219-294-8200. Also, 230-240 Volts: 5.0 A; as two independent channels. When “Bridge-
visit the Crown Audio website at At Idle: All amps draw no more than 90 Mono” mode is selected, the amplifier bridges
www.crownaudio.com. watts. the two output channels for twice the output
voltage.
Specifications AC Line Connector: NEMA 5-15P (15 A).
Reset: A front-panel push button used to
Note: All measurements relate to 120-volt, 60-Hz units in Performance reset the circuit breaker that protects the
Stereo mode with 8-ohm loads and an input sensitivity of 26-
dB gain at 1-kHz rated power unless otherwise specified. Frequency Response: ±0.2 dB from 20 Hz to power supply.
Specifications for units supplied outside the U.S.A. may vary 25 kHz at 1 watt. Sensitivity: A two-position switch located on
slightly at different AC voltages and frequencies.
Phase Response: ±15 degrees from 20 Hz to the back panel next to the Mode switch.
Power 20 kHz at 1 watt. Switchable between 1.4 volts for full output
Output Power: into an 8-ohm load (default setting), or a fixed
Signal to Noise Ratio,
A-Weighted: voltage gain of 26 dB. 0.775-volt sensitivity
Better than 105 dB below rated 1-kHz available as a Service Option.
power; Fault Jack: A back-panel RJ-11 jack that may
20 Hz to 20 kHz: be remotely monitored to signal amplifier
Better than 100 dB below rated 1-kHz Fault condition. An LED or other signalling
power. device (not supplied) may be used.
Total Harmonic Distortion (THD): 0.5% or Indicators
less true THD from 20 Hz to 20 kHz. (all located on front panel)
Intermodulation Distortion (IMD): (60 Hz Signal: A green LED for each channel which
and 7 kHz at 4:1) Less than 0.1% at rated flashes when a very low-level signal (>–40
power to 35 dB below rated power at 8 ohms. dBm) is present at input. May be used for
Damping Factor: Better than 400 from 10 Hz troubleshooting cable runs.
to 400 Hz. Clip: A red LED for each channel which turns
Crosstalk: Better than 55 dB below rated on when distortion becomes audible in the
power, 20 Hz to 20 kHz. amplifier output.
CE 2000

Fault: Normally off, this red indicator will Output Connectors: Two Neutrik® Speakon® Options
blink under five different conditions: NL4MP (mates with NL4FC) output connec- Accessories: CE-HANDLES—handle kit; SST-
1. When the amplifier is first powered up, until the tors. Optional 5-way binding post or barrier SBSC—variable Linkwitz-Riley stereo cross-
unit is ready for operation. strip outputs (in parallel with Speakon® over with mono-summed sub-bass outputs;
connectors) are available. SST-MX—100-Hz Linkwitz-Riley crossover
2. If the heatsinks reach a temperature above nor- with stereo sub-bass output; SST-SX—80-/
DC Output Offset: ±10 millivolts.
mal working limits. 120-Hz switchable Linkwitz-Riley crossover
Output Signal,
3. If the transformer thermal protection circuit is ac- with mono summed sub-bass output; CE-
Stereo: Unbalanced, two-channel;
tivated. AS1—barrier block alternate output connec-
Bridge-Mono: Balanced, single-channel. tors;* CEAS2—5-way binding post alternate
4. If amplifier output wires develop a short-circuit. Channel 1 controls are active; Channel 2 output connectors.* SST-4622, SST-3632,
should be turned down. SST-4632—custom two-channel crossover
5. Should the amplifier output stage become non-
operational. Wiring Configuration: networks with equalization and delay pur-
posely engineered for use with JBL model
This circuit may be monitored remotely by OUTUT PIN ASSIGNMENT 4622, 3632 and 4632 cinema speakers. SST-
plugging a simple switching circuit using an PIN CH PIN CH SBSC 3632T, SST-SBSC 4632T—custom
LED or other signaling device into the back- 1+ 2 1+ 1 three-channel crossover networks with CD-
panel RJ-11 (Fault) jack. Under some condi- horn equalization and mono-summed low-
1 2 1 1
tions, the output of the amplifier will be frequency outputs similarly designed for use
muted. 2+ 2+ 2 with JBL model 3632T and 4632T cinema
Power: A green LED that turns on when the 2 2 2 speakers.
amplifier has been turned on and has power. Construction
CH-2 CH-1 Rugged steel chassis is formed into a durable
Input/Output
Input Connector (standard module): One package any stagehand could love. Coated
Neutrik® Combo connector for each channel Protection with environmentally friendly powder for long
which features a balanced ¼-inch (6.35-mm) CE-Series amplifiers are protected against life and ease of maintenance.
phone jack and a 3-pin female XLR connector, shorted, open or mismatched loads; over- Cooling: Proportional speed fan.
in parallel with a barrier strip termination. loaded power supplies; excessive tempera-
Dimensions: EIA Standard 19-inch rack
ture; chain destruction phenomena; input
Input Stage: Input is electronically balanced mount width (EIA RS-310-B), 5.25-inch
and employs precision 1% resistors. overload damage; and high-frequency blow-
(13.34-cm) height and 12.25-inch (31.11-cm)
ups. They also protect loudspeakers from
Input Impedance: Nominally 20 k ohms, depth behind front mounting surface.
input/output DC, large or dangerous DC
balanced. Nominally 10 k ohms, unbalanced. offsets and turn-on/turn-off transients. Weight: The CE 2000 weighs 40.3 pounds
Input Sensitivity: 1.4 volts for standard 1-kHz (18.28 kg). For shipping weight, add 6
power, or fixed 26-dB gain. 0.775-volt sensi- pounds (2.7 kg).
tivity available as a Service Option.
*Compatible with CE versions CE 1000A and CE 2000A
amplifiers (current release).

Crown’s Three-Year, No-Fault, Fully Transferable Warranty


Crown offers a Three-Year, No-Fault, Fully Transferable Warranty for every new Crown ampli-
fier—an unsurpassed industry standard. With this unprecedented No-Fault protection, your Crown International
new Crown amplifier is warranted to meet or exceed original specifications for the first three P.O. Box 1000
years of ownership. During this time, if your amplifier fails, or does not perform to original Elkhart, IN 46515-1000
specifications, it will be repaired or replaced at our expense. About the only things not cov- TEL: 219-294-8200
ered by this warranty are those losses normally covered by insurance and those caused by FAX: 219-294-8FAX
www.crownaudio.com
intentional abuse. And the coverage is transferable, should you sell your amplifier.
See your authorized Crown dealer for full warranty disclosure and details. For customers Specifications subject to change without prior notice.
outside of the USA, please contact your authorized Crown distributor for warranty information Crown and Macro-Tech are registered trademarks of Crown
International. Other trademarks are the property of their
or call 219-294-8200. respective owners. Printed in U.S.A.
©
2001 Crown Audio, Inc.

08/01 128391-2

Anda mungkin juga menyukai