Pipe supports UN
Pipe clamps form F and form FK 3790-33
Design dimensions, weights and allowable loads;
based on American Standards Page 1 of 10
Rohrhalterungen; Schellen Form F und Form FK; Konstruktionsmaße,
Gewichte und zulässige Belastungen; basierend auf Amerikanische Standards
Contents
Page
1 Scope .................................................................................................................................................................... 1
2 Units, abbreviated terms ..................................................................................................................................... 1
2.1 Units....................................................................................................................................................................... 1
2.2 Abbreviated terms .................................................................................................................................................. 1
3 General information ............................................................................................................................................. 1
4 Clamps form F, DS 115 to DS 615....................................................................................................................... 2
4.1 Designation ............................................................................................................................................................ 5
5 Clamps form FK, DS 61 to DS 615 ...................................................................................................................... 5
5.1 Designation ............................................................................................................................................................ 9
6 Materials and property classes........................................................................................................................... 9
Reference standards ......................................................................................................................................................... 10
1 Scope
This Uhde standard (UN) applies to the design and construction of industrial and chemical plants. It contains
requirements about design dimensions, weights and allowable loads of the clamps form F and form FK for
uninsulated and heat-insulated steel rising pipes. American Standards with metric dimensions are based for
this pipe clamps.
Copyright reserved
3 General information
The standard part numbers refer to the materials specified in the section "Materials and property classes".
Other part numbers are required when changing the material.
UF GP-ST-01 F01 E 2012-02
s
of pipe ASME B36.10M
R
F
D
S
G B A B G
FV
D1 D2
C
K
M
E
C
Part number
MS0021A
MS0023A
Figure 1. Clamps form F
Table 2. Clamps form F, design dimensions and total weights
Clamp inside
Developed
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
Pipe supports
356 350 14" 355.6 355.6 1046 31200 510 145 50 800 50 26 59.12
407 400 16" 406.4 406.4 180 20 1113 31360 570 840 45 90 22 30 30 62.91
135
457 450 18" 457 457 1201 30280 630 900 67.88
508 500 20" 508 508 1315 61700 710 960 123.87
240 25 125 65 60 120 26 65 33 38
3790-33
Page
UN
March 2018
3
10of
Table 3. Clamps form F, hexagon bolts with hexagon nuts and tubular spacers
Nominal
Nominal
Pipe supports
356 350 14" 355.6 355.6 M24
407 400 16" 406.4 406.4 100 0.55 M20 100 0.36 33.4 2.77 30 0.063
457 450 18" 457 457
508 500 20" 508 508
3790-33
Page
UN
March 2018
4
10of
Draft (used for KXEO-00045) March 2018
Pipe supports UN
Pipe clamps form F and form FK 3790-33
Design dimensions, weights and allowable loads;
based on American Standards Page 5 of 10
4.1 Designation
For the designation of "clamp form F" clamp inside diameter DS shall be specified in addition to the part
number (refer to Example 1).
For the designation of "hexagon bolt with hexagon nut" the thread and the bolt length shall be specified in
addition to the part number (refer to Example 2).
For the designation of "tubular spacer" the pipe outside diameter, the wall thickness and the length shall be
specified in addition to the part number (refer to Example 3).
Example 1: Clamp form F, part number MS0021A, clamp inside diameter DS = 273,
is designated as follows:
MS0021A 273
Example 2: Hexagon bolt (ASME B18.2.3.5M), part number MB0001A, thread diameter = M24,
bolts length = 90, with hexagon nut (ISO 4032), is designated as follows:
MB0001A M24 / 90
Example 3: Tubular spacer, part number GR0001A, pipe outside diameter = 33.4, wall thickness = 2.77,
length = 30, is designated as follows:
GR0001A 33.4 / 2.77 / 30
D
S
G B A B G
FV
D1 D2
C
K
M
E
C
Part number
MS0121A
MS0123A
Figure 2. Clamps form FK
Clamps form FK, design dimensions and total weights
Table 4. Continued
Clamp inside
Developed
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
length of Allowance loads
Insulation Pipe outside one clamp for Tmax = 300°C
thickness diameter Plate segment in N
2) 1)
D
Pipe supports
77 76.1 50
> 110 ≤ 220 998 1330 360 880 10.03
≤ 110 805 3500 250 680 12.64
89 80 3" 88.9 88.9 100 180 25 50 50
> 110 ≤ 220 1025 2560 360 900 16.09
≤ 110 835 4380 245 700 15.73
3790-33
100
Page
≤ 110 1306 23760 225 960 73.82
UN
March 2018
356 350 14" 355.6 355.6 180 20 510 45 90 22 90 30
> 110 ≤ 220 1526 17550 335 1180 86.25
6
1) Weight for 2 clamp segments, without hexagon head bolts and hexagon nuts.
2) The specified loads are not equivalent to the loads for complete pipe supports (e.g. pipe shoes, tubular supports).
10of
Table 4. Continued
Clamp inside
Developed
Weight in
pipe size
diameter
diameter
kg/piece
Nominal
Nominal
length of Allowance loads
Insulation Pipe outside one clamp for Tmax = 300°C
thickness diameter Plate segment in N
2) 1)
D
DS DN NPS EN ASME M s FV A B G H C E D1 K D2 F R
Pipe supports
615 600 24" 610 610 810
> 110 ≤ 220 1904 36910 305 1420 179.36
1) and 2) see page 6.
UN
March 2018
7
10of
Table 5. Clamps form FK, hexagon bolts with hexagon nuts and tubular spacers
Nominal
Nominal
Pipe supports
169 150 6" 168.3 168.3
80 0.30 70 0.09
220 200 8" 219.1 219.1
273 250 10" 273 273
90 0.51 M16 80 0.18
324 300 12" 323.9 323.8
3790-33
Page
UN
March 2018
8
10of
Draft (used for KXEO-00045) March 2018
Pipe supports UN
Pipe clamps form F and form FK 3790-33
Design dimensions, weights and allowable loads;
based on American Standards Page 9 of 10
5.1 Designation
For the designation of "clamp form FK" clamp inside diameter DS and dimensions H shall be specified in
addition to the part number (refer to Example 4).
For the designation of "hexagon bolt with hexagon nut" the tread and the bolt length shall be specified in
addition to the part number (refer to Example 5).
For the designation of "tubular spacer" the pipe outside diameter, the wall thickness and the length shall be
specified in addition to the part number (refer Example 6).
Example 4: Clamp form FK, part number MS0121A, clamp inside diameter DS = 273,
dimension H = 1020, is designated as follows:
MS0121A 273 / 1020
Example 5: Hexagon bolt (ASME B18.2.3.5M), part number MB0001A, thread diameter = M20,
bolts length = 180, with hexagon nut (ISO 4032), is designated as follows:
MB0001A M20 / 180
Example 6: Tubular spacer, part number GR0001A, pipe outside diameter = 33.4, wall thickness = 2.77,
length = 30, is designated as follows:
GR0001A 33.4 / 2.77 / 30
Reference standards
other standards
ASME B18.2.1 : 2012 Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex
Flange, Lobed Head, and Lag Screws (Inch Series)
ASME B18.2.2 : 2015 Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange,
and Coupling Nuts (Inch Series)
ASME B36.10M : 2015 Welded and Seamless Wrought Steel Pipe
ASTM A6/A6M : 2017 Rev. A Standard Specification for General Requirements for Rolled Structural Steel
Bars, Plates, Shapes, and Sheet Piling
ASTM A36/A36M : 2014 Standard Specification for Carbon Structural Steel
ASTM A53/A53M : 2012 Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated,
Welded and Seamless
ASTM A193/A193M : 2017 Standard Specification for Alloy-Steel and Stainless Steel Bolting for High
Temperature or High Pressure Service and Other Special Purpose
Applications
ASTM A194/A194M : 2017 Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High
Pressure or High Temperature Service, or Both
ASTM A307 : 2014 Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod
60 000 PSI Tensile Strength
ASTM A335/A335M : 2017 Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-
Rev. A Temperature Service
ASTM A387/A387M : 2017 Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-
Molybdenum
ASTM A563 : 2015 Standard Specification for Carbon and Alloy Steel Nuts
ASME B18.2.3.5M
ISO 4032