id
Phone. 08129004021
BIRO KLASIFIKASI INDONESIA
Indonesian Flag Ship Load Line Survey
Peraturan Menteri
International Convention Perhubungan PM.39
on Load Line 1966 Tahun 2016 tentang Garis
(ICLL 1966) Muat Kapal & Pemuatan
(PM.39/ 2016)
BIRO KLASIFIKASI INDONESIA
The overall objectives
Safe working platform for
Adequate reserve buoyancy
the crew (the freeboard is
(weather conditions and sea
prepared on the basis of
state)
deck wetness principle)
Loadline marked on the
ship’s sides
BIRO KLASIFIKASI INDONESIA
ICLL 1966
Applies to ships in
Came into force 1 July international traffic with a
1968 length of 24 m and more
(Article 4 & 5)
BIRO KLASIFIKASI INDONESIA
4
Article 5 : Exceptions
Ships of war
New ships of less than 24 metres in length
Existing ships of less than 150 tons gross
Pleasure yachts not engaged in trade
Fishing vessels
BIRO KLASIFIKASI INDONESIA
ICLL 1966: Contents
Annex I – Regulations for determining Load Lines
• Chapter I: General
• Chapter II: Assignment of freeboard
• Chapter III: Freeboards
• Chapter IV: Timber freeboard
Annex II – Zones, areas and seasonal periods
Annex III ‐ Certificates
BIRO KLASIFIKASI INDONESIA
Chapter I: General
Stability & Strength Subdivision
•The regulations assume that •The regulations also assume
the nature and stowage of the that where there are
cargo, ballast, etc., are such as to international requirements
secure sufficient stability of the relating to stability or
ship and the avoidance of subdivision, these requirements
excessive structural stress have been complied with
BIRO KLASIFIKASI INDONESIA
Strength and Intact Stability (Reg. 1)
General structural strength of the ship is
adequate for the draught corresponding
to the freeboard assigned.
BIRO KLASIFIKASI INDONESIA
BIRO KLASIFIKASI INDONESIA
9
Sheer Force & Banding Moment
BIRO KLASIFIKASI INDONESIA
Hydrostatic Pressure Diagram
p = water·g·d (N)
F = p·A
(Nm)
d
BIRO KLASIFIKASI INDONESIA
11
Hydrostatic Pressure Diagram
BIRO KLASIFIKASI INDONESIA
12
TORSIONAL FORCES
BIRO KLASIFIKASI INDONESIA
13
HULL DEFORMATION
BIRO KLASIFIKASI INDONESIA
14
Load Line Survey
Initial Survey Annual Survey Renewal Survey
to be done
to be done
Initial report to before the
within 3 months expiry date
be stored on
before or after
board anniversary (the certificate
is valid for 5
date years)
BIRO KLASIFIKASI INDONESIA
Ini
Initial Survey Report
To be
stored on
board
BIRO KLASIFIKASI INDONESIA
Annual Survey
1. Ensure that no alterations have been made
BIRO KLASIFIKASI INDONESIA
Alterations of the
Ship
Reduction of Ship's
Flag transfer Strength (Class
withdrawal)
Deficiencies in:
Not endorsed • Closing appl.
Certificate (Annual
Invalid • Railings
BIRO KLASIFIKASI INDONESIA
Port State Control (Art. 21)
Ships are subject to port state control, to verifying that there is on
board a valid Load Line Certificate.
If there is a valid Certificate on board the ship, such control shall be
limited to the purpose of determining that:
• a) the ship is not over loaded
• b) the position of the load line mark corresponds with the certificate
• c) the ship has not been so materially altered in respect of the matters set out
in sub‐paragraphs (a) and (b) of paragraph (3) of Article 19 that the ship is unfit to
proceed to sea without danger to human life
BIRO KLASIFIKASI INDONESIA
Information to be supplied to the Master
(Reg. 10)
•The master shall be supplied with sufficient information, to arrange for the loading and
to be supplied ballasting of this ship in such a way as to avoid the creation of any unacceptable stresses
in the ship's structure, provided that this requirement need not apply to any particular
length, design or class of ship where the Administration considers it to be unnecessary.
to be kept on •Stability information, and loading information also related to ship strength when
required, shall be carried on board at all times together with evidence that the
board information has been approved by the Administration.
Any Alterations •Where any alterations are made to a ship so as to materially affect the loading or
stability information supplied to the master, amended information shall be provided. If
to be amended necessary the ship shall be re‐inclined.
BIRO KLASIFIKASI INDONESIA
REGULATION 3:
Definitions and terms
BIRO KLASIFIKASI INDONESIA
21
Length (L)
The length (L) shall be taken as 96% of the total length on a waterline at 85% of the least moulded depth
measured from the top of the keel, or as the length from the fore side of the stem to the axis of the rudder
stock on that waterline, if that be greater.
For ships without a rudder stock, the length (L) is to be taken as 96% of the waterline at 85% of the least
moulded depth.
BIRO KLASIFIKASI INDONESIA
BIRO KLASIFIKASI INDONESIA
BIRO KLASIFIKASI INDONESIA
BIRO KLASIFIKASI INDONESIA
BIRO KLASIFIKASI INDONESIA
Breadth (B)
Breadth is the maximum breadth of the ship, measured amidships to the moulded line of the frame
in a ship with a metal shell and to the outer surface of the hull in a ship with a shell of any other
material
BIRO KLASIFIKASI INDONESIA
Rake of Keel
Rake of keel is defined as the height the keel raises from AP to FP
BIRO KLASIFIKASI INDONESIA
Moulded Depth
The moulded depth is the vertical distance measured from the top of the keel to the top of the freeboard
deck beam at side
Defined as illustrated in the sketches below:
BIRO KLASIFIKASI INDONESIA
Moulded Depth
The moulded depth is the vertical distance measured from the top of the keel to the top of the freeboard
deck beam at side
BIRO KLASIFIKASI INDONESIA
Definition
(Reg. 3)
• The depth for freeboard (D) is the moulded depth amidships, plus the freeboard
deck thickness at side.
BIRO KLASIFIKASI INDONESIA
Superstructure
BIRO KLASIFIKASI INDONESIA
32
Definition: Enclose Superstructure
(Reg. 3)
An enclosed superstructure is a superstructure with:
• enclosing bulkheads of efficient construction;
• access openings, if any, in these bulkheads fitted with doors
complying with the requirements of Regulation 12;
• all other openings in sides or ends of the superstructure fitted with
efficient weathertight means of closing.
BIRO KLASIFIKASI INDONESIA
Freeboard Deck
The freeboard deck is normally the uppermost complete deck
exposed to weather and sea, which has permanent means of
closing all openings in the weather part thereof, and below
which all openings in the sides of the ship are fitted with
permanent means of watertight closing.
BIRO KLASIFIKASI INDONESIA
Watertight & Weathertight
BIRO KLASIFIKASI INDONESIA
Regulation 6: Lines to be used with the Load Line Mark
BIRO KLASIFIKASI INDONESIA
Fresh Water Allowance (Art. 12)
ICLL Reg 40: Fresh water allowance: Δ/40T cm deduction from the summer (salt water)
load line
Δ = displacement (tonnes) at the summer load waterline
T = tonnes/cm immersion at the summer load waterline
If the displacement at the summer load waterline cannot be certified, the deduction
shall be 1/48 of the summer loadline draft
BIRO KLASIFIKASI INDONESIA
BIRO KLASIFIKASI INDONESIA
BIRO KLASIFIKASI INDONESIA
Items to be shown on
the Freeboard
Plan
BIRO KLASIFIKASI INDONESIA
40
Superstructure End Bulkheads
(Reg. 11)
Bulkheads at exposed ends of enclosed
superstructures shall be of an acceptable
level of strength.
BIRO KLASIFIKASI INDONESIA
Doors
(Reg. 12)
• All access openings in bulkheads at ends of enclosed
superstructures shall be fitted with doors of steel or other
equivalent material, permanently and strongly attached to the
bulkhead, and framed, stiffened and fitted so that the whole
structure is of equivalent strength to the un-pierced bulkhead and
weathertight when closed.
• The means for securing these doors weathertight shall consist of
gaskets and clamping devices or other equivalent means and shall
be permanently attached to the bulkhead or to the doors
themselves, and the doors shall be so arranged that they can be
operated from both sides of the bulkhead.
• Unless otherwise permitted by the Administration, doors shall open
outwards to provide additional security against the impact of the
sea.
BIRO KLASIFIKASI INDONESIA
Doors
(Reg. 12)
• Portable sills shall be avoided. However,
in order to facilitate the loading/unloading
of heavy spare parts or similar, portable
sills may be fitted on the following
conditions:
(a) they shall be installed before the ship
leaves port; and
(b) they shall be gasketed and fastened by
closely spaced through bolts.
• .
BIRO KLASIFIKASI INDONESIA
Position of Hatchways, Doorways and
Ventilators
(Reg. 13)
• Position 1 Upon exposed freeboard and raised quarter
decks, and upon exposed superstructure decks situated
forward of a point located a quarter of the ship's length
from the forward perpendicular.
• .
BIRO KLASIFIKASI INDONESIA
POSISI 1 DAN POSISI 2
BIRO KLASIFIKASI INDONESIA
POSISI 1 & 2 PADA GELADAK LAMBUNG TIMBUL DAN GELADAK
BANGUNAN ATAS
BIRO KLASIFIKASI INDONESIA
TINGGI STANDARD SUPERSTRUCTURE DAN RAISED
QUARTERDECK
• Geladak penggal yang ditinggikan :
‐ Untuk panjang kapal s/d 30 m; h = 0.90 m,
‐ Untuk panjang kapal 75 m; h = 1.20 m,
‐ Untuk panjang kapal 125 m atau lebih; h = 1.80 m.
• Bangunan Atas
‐ Untuk panjang kapal kurang dari 125 m; h = 1.80 m,
‐ Untuk panjang kapal 125 m atau lebih h = 2.30 m
BIRO KLASIFIKASI INDONESIA
Persyaratan Tinggi Ambang
• Pintu (door)
Posisi 1: 600 mm
Posisi 2: 380 mm
• Bukaan Palka
Posisi 1: 600 mm
Posisi 2: 450 mm
BIRO KLASIFIKASI INDONESIA
Persyaratan Tinggi Ambang
• Ventilator
Posisi 1: 900 mm
Posisi 2: 760 mm
Apabila tinggi ambang > 4500 mm pada posisi 1 dan >2300
mm pada posisi 2, tidak disyaratkan untuk dilengkapi
dengan peralatan penutup
• Pipa udara
Freeboard deck: 760 mm
Superstructure deck: 450 mm
BIRO KLASIFIKASI INDONESIA
TINGGI AMBANG PINTU PADA POSISI 1 & 2
BIRO KLASIFIKASI INDONESIA
TINGGI VENTILASI DAN PIPA UDARA PADA POSISI 1 & 2
BIRO KLASIFIKASI INDONESIA
ACCEPATBLE ARRANGEMENT of SCUPPER, INLETS AND DISCHARGE
D isch a rg e co m in g fro m e n c lo se d sp a ce b e lo w th e fre e b o a rd d e ck o r o n th e
D isc h a rg e s co m in g fro m o th e r sp a ce s
fre e b o a rd d e ck
G e n e ra l re q u ire m e n t D isch a rg e O u tb o a rd e n d > 4 5 0 m m
A lte rn a tive s (R e g . 2 2 (1 )) w h e re in b o a rd e n d o th e rw ise
R e g . 2 2 (1 ) w h e re tro u g h b e lo w F B d e ck o r
in b o a rd e n d < 0 ,0 1 L m a ch in e ry 6 0 0 m m a b o ve S W L
> 0 ,0 1 L a b o ve S W L > 0 ,0 2 L a b o ve S W L R e g . 2 2 (5 )
a b o ve S W L sp a ce R e g . 2 2 (4 )
S u p e rstru ctu re
o r D e ckh o u se D e ck
FB FB FB FB FB FB
D e ck D e ck D e ck D e ck D e ck D e ck
TW L
SW L SW L SW L SW L SW L SW L
BIRO KLASIFIKASI INDONESIA
PIPA UDARA
VENTILASI
BIRO KLASIFIKASI INDONESIA
SMALL HATCH
PIPA UDARA
BIRO KLASIFIKASI INDONESIA
TIPE‐TIPE PIPA UDARA
BIRO KLASIFIKASI INDONESIA
TOGGLE UNTUK
KEKEDAPAN PINTU
KEKEDAPAN BUKAAN HARUS
DIPERTAHANKAN
BIRO KLASIFIKASI INDONESIA
KARET UNTUK KEKEDAPAN
BIRO KLASIFIKASI INDONESIA
PENENTUAN DRAFT MARK
BIRO KLASIFIKASI INDONESIA
PENULISAN DRAFT MARK
BIRO KLASIFIKASI INDONESIA
Side Scuttles, windows and skylights
(Reg. 23)
BIRO KLASIFIKASI INDONESIA
Side scuttles to the following spaces shall be
fitted with hinged inside deadlights:
• spaces below freeboard deck;
• spaces within the first tier of enclosed
superstructures; and
• first tier deckhouses on the freeboard deck
protecting openings leading below or
considered buoyant in stability
calculations.
BIRO KLASIFIKASI INDONESIA
Side Scuttles, windows and skylights
(Reg. 23)
BIRO KLASIFIKASI INDONESIA
Side Scuttle
BIRO KLASIFIKASI INDONESIA
Windows shall not be fitted in the following
locations:
• below the freeboard deck;
• in the first tier end bulkheads or sides of
enclosed superstructures; or
• in first tier deckhouses that are considered
buoyant in the stability calculations.
BIRO KLASIFIKASI INDONESIA
LUBANG PEMBEBASAN (FREEING PORT)
(Reg. 24)
Luas lubang pembebasan (a )
• Untuk panjang bulwark ℓ kurang atau sama dengan 20 m
a = 0.7 + 0.035 · ℓ m2
• Apabila panjang bulwark ℓ lebih dari 20 m
a = 0.07 · ℓ m2
• Dimana ℓ diambil maksimal 0.7 · L
catatan :
ℓ = panjang bulwark
L = panjang kapal
BIRO KLASIFIKASI INDONESIA
Protection of the Crew
(Reg. 25)
• The deckhouses used for the accommodation of the
crew shall be constructed to an acceptable level of
strength.
• Guard rails or bulwarks shall be fitted around all exposed
decks
• The height of the bulwarks or guard rails shall be at least
1 metre from the deck, provided that where this height
would interfere with the normal operation of the ship, a
lesser height may be approved if the Administration is
satisfied that adequate protection is provided.
BIRO KLASIFIKASI INDONESIA
Types of Ships
(Reg. 27)
• Type ‘A’ ship is one which:
– is designed to carry only liquid cargoes in bulk;
– high integrity of the exposed deck with only small access
openings to cargo compartments, closed by watertight gasketed
covers of steel or equivalent material; and
– has low permeability of loaded cargo compartments.
• Type “B”ship
BIRO KLASIFIKASI INDONESIA
Penetapan Lambung Timbul kapal
• Persyaratan kekuatan konstruksi harus
terpenuhi
• Persyaratan kemampuan stabilitas harus
terpenuhi
• Persyaratan loadline harus terpenuhi
BIRO KLASIFIKASI INDONESIA
FAKTOR‐FAKTOR YANG MENYEBABKAN PENAMBAHAN LAMBUNG
TIMBUL
• Koefisien Blok pada 0.85 H melebihi 0.68,
• Tinggi lengkung kapal (sheer) berbeda lengkung standar,
• Kapal tidak mempunyai bangunan atas tertutup,
• Adanya persyaratan tinggi haluan minimum,
BIRO KLASIFIKASI INDONESIA
FAKTOR FAKTOR YANG MENYEBABKAN PENGURANGAN
LAMBUNG TIMBUL
• Adanya bangunan atas tertutup dan atau trunk,
• Sheer berbeda dengan sheer standar
• Tongkang tak berawak dengan bukaan di geladak yang kecil
(contoh flat top barge, pontoon, dll).
BIRO KLASIFIKASI INDONESIA