Anda di halaman 1dari 6

Lähde:

https://aviation.stackexchange.com/questions/13257/how-
come-planes-can-endure-more-positive-than-negative-gs-i-e-
how-come-v-n-di
Log In Sign Up Aviation Stack Exchange is a question and answer site
for aircraft pilots, mechanics, and enthusiasts. Join them;
it only takes a minute:

Sign up

Here's how it works:


Anybody can ask a question
Anybody can answer
The best answers are voted up and rise to the top

How come planes can endure more positive than negative g's? I.e. how come V-n diagrams are not
symmetric?
Ask Question

16

In this question A380 reverse thrust on only half the engines some doubts were raised about the strength of structures in certain directions. Specifically, Peter
Kämpf states:

Aluminium and Carbonfiber are almost as good in compression as in tension, so the direction of the load is secondary. This is not true if buckling stiffness is
not sufficient, but in case of wing in-plane bending, buckling is of no concern.

This made me wonder:

How come V-n diagrams are not symmetric?

From the image it can be seen that the structure at 150 knts can only cope with -1.8g, but +3.8g. Where does this difference come from, is it coming from
difference in buckling stifnesses in different directions?

aircraft-design aircraft-limitations aircraft-structures

share improve this question

edited Apr 13 '17 at 12:59

Community ♦
1

asked Mar 15 '15 at 14:16

ROIMaison
3,672 20 56

3 Answers active oldest votes

By using our site, you acknowledge that you have read and understand our Cookie Policy, Privacy Policy, and our Terms of Service.

16
The lines start at zero load factor because with no speed there is no lift. If you move further right, the upper line is determined by the maximum lift, while the lower
line is determined by the minimum lift. Both have the same value only for symmetric airfoils - regular airfoils are optimized for creating lift in only one direction.

The upper and lower maximum load factor limits of the v-n-diagram are mostly determined by maximum gust loads in level flight, and in this condition they are
represented by lines emanating from +1 g, such that the distance from +1 g in terms of positive and negative load factors should be the same. Add to this that
your wings will create approximately 50% more force until they reach their maximum lift as compared to the minimum ( = maximum negative) lift (the details
depend on the airfoil, of course), and then your load factor limits will be 1 + 1.5 ⋅ gust load factor in positive and 1 - gust load factor in negative direction.

For an example I have uploaded the polar of a supercritical airfoil which I calculated years ago with Mark Drela's ISES. It's the best I could find quickly - most
polars only show the positive maximum lift, not the limit at the opposite end.

As you can see, the maximum c L is +1.3, while the minimum c L is only -0.8.

Let's look at a practical case: Utility category airplanes must be certified for +3.8 gs and -1 g. In level flight a positive vertical gust (updraft) might add +2.8 g. The
same gust strength in negative direction (downdraft) will cause a load change of only -1.9 g (because the wing will stall earlier), which, when added to the regular
1 g at level flight will translate into a -0.9 g load factor. Close enough for limiting the negative load factor at -1 g.

At higher speed the gust will not stall the airfoil in either direction, and now we can simply assume that a gust will produce a positive load of 1 + gust load factor
and a negative load of 1 - gust load factor. Let the gust load factor be 2.8, and your limits will be +3.8g and -1.8g, like in your example at 150 kts.

So far, I have looked at the rationale behind the load limits for certification. But also in real life there is a difference between positive and negative load factors:
The wing spar has to carry the bending moment due to lift minus the wing weight. If it would need to carry the same aerodynamic loads in both directions (up and
down), the wing weight would reduce the total positive load, but would make the total negative load greater. This is why the structure cannot endure the same
load factors in both directions: You need to give the wing some margin to carry its own weight in addition to the aerodynamic loads.

Things look differently if you take the v-n-diagram of aerobatic category airplanes. Now you cannot readily assume that the plane will only fly straight, but you
need to assume that it will be hit by a gust while flying upside down. Add to this that the symmetric airfoil will create the same lift in both directions before it stalls,
and your envelope needs to be limited at ±6 g, making the envelope symmetric.
share improve this answer

edited May 10 '15 at 9:11

answered Mar 15 '15 at 14:44

Peter Kämpf
162k 12 411 656

Hi Peter, I've changed the image to the better image you recommended, so perhaps your comments relating to my example are not correct anymore. – ROIMaison Mar 16 '15 at
11:45

Do you also know the reason why the region of structural damage is different for positive and negative? The region of structural damage goes from +3.8 to +5.5 (where structural failure
starts), so that's 1.7g difference. At the negative g range, the structural damage goes from -1.8 to -2.6, which is only 0.8g's difference. Do you know what the reason is for this (large)
difference? – ROIMaison Mar 31 '16 at 15:36

@ROIMaison: The shaded area with structural damage is unusual already, and I guess the limits are artificial. Someone probably wanted to add that at 150% of limit load the structure
is at its ultimate load and will fail. They just took the nominal g value and added 50% for the failure limit, without calculating exactly where the real limits are. – Peter Kämpf Mar 31 '16
at 21:59
9

To put it simply, it is because the aircraft is designed to be stronger in the +G direction. It is not required to be as strong in the -G direction (since it will not
experience high negative G loads during operations), so it is not designed that way. To do so would cause much unnecessary structural weight.
share improve this answer

answered Mar 16 '15 at 0:38

Porcupine911
2,923 13 30

And the reason for this is probably that there are humans on board who tolerate a decrease of blood pressure in the brain better than an increase. – vsz Dec 28 '15 at 0:28

There are many engineering factors that determine g ratings. The cumulative fatigue damage from dominant operations primarily determine g-ratings. When
landing, this contributes heavy fatigue positive g's. When flying, the natural forces of gravity and turbulence (to include gusting winds) contribute to fatigue
damage. These stresses are felt throughout the control systems. Therefore, the plane is engineered to be stronger in all its considerations to support and counter
the greater fatigue concerns.

http://adg.stanford.edu/aa241/structures/structuraldesign.html

How come V-n diagrams are not symmetric?

V-n Diagrams tend to visually reflect some of the more dominant fatigue considerations. Engineered considerations that influence g ratings also are reflected in
the V-n Diagrams for similar reasons. Notice the sharp changes in shape in the following Vn diagram and its explanations:

http://adg.stanford.edu/aa241/structures/vn.html

So why not strengthen everything to have higher g limits? Cost and useful return on investment. There is little practicality to have an aircraft stressed to +/- 100
g's if it has little useful load, is too heavy to fly, or costs so much very few customers can afford buying it and pay for its operation.

Balances in weight, cost, strength... are in constant flux throughout design to provide an overall useful and affordable aircraft. Equal g ratings is not a priority,
however, meeting regulatory minimums is a priority.

https://www.faa.gov/about/office_org/headquarters_offices/avs/offices/air/directorates_field/small_airplanes/media/CPS_Part_23.pdf

There are normal and abnormal conditions in which an airplane is stressed for negative g's.

Normal negative g's include: in-flight turbulence, recovery from a bounced landing, down drafts / wind shear ... and other engineered limits that are reflected in
negative g ratings.

Abnormal negative g's include: walking on or otherwise loading the top of a wing, unrated aerobatics, excessive snow loading while parked, excessive pilot
induced control moments causing negative g's, excessive road bumps while in transport ...

Conditions violating negative g design considerations include: improperly secured or excessively worn folding wing hardware, worn or warped wing gusset or
related fastening hardware, fatigued or weak weldments, corrosion ...

G-ratings have to do with Damage Tolerance

As a point of reference. Fatigue failures are usually more significant at gross weight, and therefore utility and ultimate g ratings (regulatory) are usually given at
gross weight.

Strength of Materials is a particular area of science and engineering that characterizes properties of materials, including fatigue. Computer simulations can run
thousands of tests using variations in parameters to anticipate fatigue failures before they actually occur in flying aircraft.

An aircraft can be engineered to have greater negative g limits than positive g limits; however the cost for this non-useful engineered feature would likely be
unacceptable to customers. Lower useful weight to have the higher negative g support structure as an example.

How come planes can endure more positive than negative g's?

However, the FAA over many years of experience has set standards for minimum g ratings to help control accident outcomes.

As an example, see Part 25 AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Subpart C--Structure Fatigue Evaluation Sec. 25.571
Damage-tolerance and fatigue evaluation of structure.

http://lessonslearned.faa.gov/Comet1/25.571.pdf

and an A/P's insights under the following debrief:

https://www.faasafety.gov/files/gslac/library/documents/2011/Jul/55585/FLYING%20LESSONS%20110623.pdf

In terms of engineering to meet regulatory requirements, the cumulative probability of fatigue failure resulting from negative g's is less than the cumulative
probabilities of fatigue failure from positive g's. The design limits reflect these failures through probability equations relating likeliness to occur and level of impact.

FAA SYSTEM SAFETY ANALYSIS AND ASSESSMENT (acceptable methods) http://www.faa.gov/documentLibrary/media/Advisory_Circular/AC%2023.1309-


1E.pdf

Methods of working probability equations: http://people.qatar.tamu.edu/shehab.ahmed/ecen_459/Lec34-37.pdf

The information provided in these links are to show the effort involved is no small task for aircraft designers. Many thousands of failure modes accumulate when
every part, joint, human error, environmental, and every other factor potentially part of a failure is considered.

So when asking a designer what the effect would be on g-rating based on a specific failure mode of a part, is not a reasonable question to ask because of the
extensive interactions with the total system to be considered.
share improve this answer

edited Mar 15 '17 at 17:17


answered Mar 30 '16 at 22:25

Toni
41 3

@SMSvonderTann Personally, I think it's fine. It's not the brightest, to the point answer, but it's also not something I would want to see gone. Toni, perhaps you could improve the
answer, and directly address the OPs points? – Zizouz212 Mar 30 '16 at 23:30

Your Answer

Sign up or log in
Sign up using Google

Sign up using Facebook

Sign up using Email and Password

Post as a guest
Name

Email
Required, but never shown

Post Your Answer

By clicking "Post Your Answer", you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged aircraft-design aircraft-limitations aircraft-structures or ask your own question.

asked 4 years, 1 month ago

viewed 3,552 times

active 2 years, 1 month ago

FEATURED ON META

Planned maintenance scheduled April


17/18, 2019 at 00:00UTC (8:00pm
US/Eastern)
Announcing the arrival of Valued
Associate #679: Cesar Manara
Unicorn Meta Zoo #1: Why another
podcast?

Linked

5
Why can planes generally take more positive g's
than negative g's?

16
Does stall angle of attack in inverted flight change
due to the camber of an asymmetric airfoil?

1
A380 reverse thrust on only half the engines

Related

18

What are the factors that limit how long an aircraft


can stay aloft?

20

Why are Inline Engines more commonly used than


Radial Engines?

Why can planes generally take more positive g's


than negative g's?

34

Why are planes using rivets & not welded


construction?

what is the disadvantage of blended wing body ,that


they not used to achieve more than subsonic
speed?

How do airliner manufacturers come up with typical


capacities of their planes?

22

What are the advantages of more than 4 propeller


blades?

29

How “over-engineered” were old planes and how


“over-engineered” are they now that we have more
advanced testing and research options?

-6
Why are car engines not used for planes?

Can this design provide more lift force than thrust


from engine?

Hot Network Questions


3 doors, three guards, one stone

How to say that you spent the night with someone,


you were only sleeping and nothing else?

How to define a unique height of subscript and


superscript indices?

Binary strings such that the sum of 0's is not equal


to twice the sum of 1's

Can inflation occur in a positive-sum game


currency system such as the Stack Exchange
reputation system?

Who can trigger ship-wide alerts in Star Trek?

Why is "Captain Marvel" translated as male in


Portugal?

How to select CMU Sans Serif Bold in XeTeX?

Estimate capacitor parameters

Can a drone be seen on TCAS?

What is a quick way to find the reverse


complement in bash

Can a zero nonce be safely used with AES-GCM if


the key is random and never used again?

What causes the vertical black lines in my photo?

What do you call the holes in a flute?

What do I do if technical issues prevent me from


filing my return on time?

Jazz greats knew nothing of modes. Why are they


used to improvise on standards?

How should I respond to a player wanting to catch


a sword between their hands?

Can rocky hills similar to the Scottish highlands be


located next to a bog?

What would be Julian Assange's expected


punishment, on the current English criminal law?

Can I add database to AWS RDS MySQL without


creating new instance?
Can a non-EU citizen traveling with me come with
me through the EU passport line?

How to set input type 'Select' in ui_component grid


in magento 2.1.16

Why use gamma over alpha radiation?

Simulating Exploding Dice

question feed

AVIATION

Tour
Help

Chat
Contact

Feedback
Mobile

Disable Responsiveness

COMPANY

Stack Overflow

Stack Overflow Business

Developer Jobs

About
Press

Legal

Privacy Policy

STACK EXCHANGE
NETWORK

Technology
Life / Arts

Culture / Recreation

Science

Other

Blog

Facebook

Twitter
LinkedIn
site design / logo © 2019 Stack Exchange Inc; user contributions licensed under cc by-sa 3.0 with attribution required. rev 2019.4.12.33321

Anda mungkin juga menyukai