TABLE CONTENT
1 INTRODUCTION
2 CODE/STANDARD & SOFTWARE CALCULATION
3 MODELLING & ASSUMPTION
4 MATERIAL PROPERTIES
5 DESIGN DATA
6 LOADING & COMBINATION
7 RESULT
8 APPANDIX
Page 1 of 6
Job Name: SEPARATOR AND PW DEGASSER SKID Subject: STRUCTURAL CALCULATION
Doc Number: AL2430-207 Rev B Originator: LDA Checker: LCH
1 INTRODUCTION
Overal dimension of skid
Length 22.97 ft = 7,000 mm
Width 7.05 ft = 2,150 mm
Height 11.74 ft = 3,577 mm
Dimension of frame structure (support skid).
Length 22.97 ft = 7,000 mm
Width 7.05 ft = 2,150 mm
Height 7.22 ft = 2,200 mm
Overal dimension of Instrument.
Length 22.97 ft = 7,000 mm
Width 7.05 ft = 2,150 mm
Height 4.52 ft = 1,377 mm
There are the analysis cases follow:
- Operation analysis case (full water)
- Lifting analysis case
Page 2 of 6
Job Name: SEPARATOR AND PW DEGASSER SKID Subject: STRUCTURAL CALCULATION
Doc Number: AL2430-207 Rev B Originator: LDA Checker: LCH
2 CODE/STANDARD & SOFTWARE CALCULATION
AISC-ASD: American Institute of Steel Construction
Allowable Stress Design
API STANDARD 650 American Petroleum institute
ASCE 7-05: American Society of Civil Engineers
AWS D1.1: Structural Welding Code – Steel
Software: Staad.pro V8i
3 MODELLING & ASSUMPTION
Model: The software uses the Finite Element Method (FEM). FEM is a numerical technique for
analyzing engineering designs. FEM is accepted as the standard analysis method due to its generality
and suitability for computer implementation. FEM divides the model into many small pieces of simple
shapes called elements effectively replacing a complex problem by many simple problems that need to
be solved simultaneously.
4 MATERIAL PROPERTIES
Section Profile:
No. Profile Material Fu (Mpa) Fy (Mpa)
1 H250x250x9x14 SS400 400 245
2 H150x150x7x10 SS400 400 245
3 C100x50x5x7.5 SS401 400 245
Page 3 of 6
Job Name: SEPARATOR AND PW DEGASSER SKID Subject: STRUCTURAL CALCULATION
Doc Number: AL2430-207 Rev B Originator: LDA Checker: LCH
W1 = 0.3*WS = 18540.90 (N) With WS= 2500(KG): Total weight of Shell
X1= 0.38*H = 0.76 (m) With H= 1.5(m): Maximum design liquid level
W2 = 0.63*WS = 38935.89 (N) With WS= 2500(KG): Total weight of Shell
X2= 0.56*H = 1.12 (m) With H= 1.5(m): Maximum design liquid level
Overturning Moment axial X shall be transmitted to structure by 1 pair of torque:
F = ± M/L = 40.84 (KN)= 4163 (KG)
and Overturning Moment axial Z shall be transmitted to structure by 2 torques
MZ = M/2 = 23.69 (KNm) = 2415 (Kgm)
Vertical load shall be applied at beams at top and bottom of skid:
F1X=F1Z=F1 = ZIWSTC1= 575 (KG) (at top beam)
F2X=F2Z=F2 = ZIWSBC1 = 1347 (KG) (at bottom beam)
F3X=F3Z=F3 = ZIWSVC1 = 945 (KG) (at Saparator)
Where: WST (Total weight of top of skid) = 1825 (KG)
WSB (Total weight of bottom of skid) = 4275 (KG)
WSV (Total weight of saparator) = 3000 (KG)
Vertical load shall be transited to beam at top by area load: W1X= 64 (KG/m2)
W1Z= 64 (KG/m2)
Vertical load shall be transited to beam at bottom by area load: W1Z= 92 (KG/m2)
W2Z= 92 (KG/m2)
Vertical load shall be transited to 2 nodes of beam at bottom of saparator W3= 473 (KG)
- Lifting load:
Empty weight with dynamic factor 2 times.
6 LOADING & COMBINATION
6.1 Seismic load:
2
LC1 Seismic load about axis X W1X= 64 (KG/m )
2
W1Z= 64 (KG/m )
W3= 473 (KG) (2 nodes)
2
LC2 Seismic load about axis Z W1Z= 92 (KG/m )
2
W2Z= 92 (KG/m )
W3= 473 (KG) (2 nodes)
6.2 Dead load: LC3
Page 4 of 6
Job Name: SEPARATOR AND PW DEGASSER SKID Subject: STRUCTURAL CALCULATION
Doc Number: AL2430-207 Rev B Originator: LDA Checker: LCH
6.3 Live Load: LC4
Page 5 of 6
Job Name: SEPARATOR AND PW DEGASSER SKID Subject: STRUCTURAL CALCULATION
Doc Number: AL2430-207 Rev B Originator: LDA Checker: LCH
7 RESULT
7.1 IN-PLACE ANALYSIS
Result this case, refer appendix 2
Max. deflection at member M4 2.696 mm
Max. deflection allowable L/300 = 7.0 mm
Max. ratio at member: M4 0.716 ≤ 1
(refer item "steel design detail typical"-appendix 2)
Status Safe
Page 6 of 6
"ASCE705W.xls" Program
Version 1.0
Input Data:
Resulting Parameters and Coefficients:
Wind Speed, V = 105 mph
Class., Occ. Category = II (Table 1-1) If z < 15 then: Kz = 2.01*(15/zg)^(2/a)
Exposure Category = B (Sect. 6.5.6) If z >= 15 then: Kz = 2.01*(z/zg)^(2/a)
Topo. Factor, Kzt = 1.00 (Sect. 6.5.7) a= 7.00 (Table 6-2)
Height of Structure, h = 11.74 ft. zg = 1200 (Table 6-2)
Structure Width, B = 7.05 ft. (normal to wind) I= 1.00 (Table 6-1)
Structure Length, L = 22.97 ft. (parallel to wind) freq., f = 7.883 Hz. (f >=1) Rigid
Damping Ratio, b = 0.010 (0.010 to 0.070) G= 0.850 (Gust Factor, Sect. 6.5.8)
Period Coefficient, Ct = 0.0200 (0.020 to 0.035)
Direct. Factor, Kd = 1 (Table 6-4) Velocity Pressure (Sect. 6.5.10, Eq. 6-15):
qz = 0.00256*Kz*Kzt*Kd*V^2*I
Note: Per Code Section 6.1.4.1, design wind force for open Net Design Wind Pressures (Sect. 6.5.15):
buildings and other structures shall not be less than 10 psf p = qz*G*Cf (psf), where 'qz' is evaluated at
multiplied by the area, 'Af', the area normal to wind direction. height 'z' of the centroid of projected area.
1 of 3
"ASCE705W.xls" Program
Version 1.0
Parameters Used in Both Item #2 and Item #3 Calculations (from Table 6-2):
a^ = 0.143
b^ = 0.84
a(bar) = 0.250
b(bar) = 0.45
c= 0.30
l= 320 ft.
e(bar) = 0.333
z(min) = 30 ft.
2 of 3
"ASCE705W.xls" Program
Version 1.0
Notes: 1. Signs with openings comprising 30% or more of the gross area are classified as open signs.
2. The calculation of the design wind forces shall be based on the area of all exposed members
and elements projected on a plane normal to the wind direction. Forces shall be assumed to
act parallel to the wind direction.
3. The area 'Af' consistent with these force coefficients is the solid area projected normal to the
wind direction.
4. Notation:
e = ratio of solid area to gross area
D = diameter of a typical round member, in feet.
qz = velocity pressure evaluated at height 'z' above ground in psf.
Notes: 1. For all wind directions considered, area 'Af' consistent with force coefficients shall be solid area
of tower face projected on plane of that face for tower segment under consideration.
2. Specified force coefficients are for towers with structural angles or similar flat-sided members.
3. For towers containing rounded member, it is acceptable to multiply specified force coefficients
by following factor when determining wind forces on such members: 0.51*e^2 + 0.57 <= 1.0.
4. Wind forces shall be applied in directions resulting in maximum member forces and reactions.
For towers with square cross-sections, wind forces shall be multiplied by following factor when
wind is directed along a tower diagonal: 1+ 0.75*e <= 1.2.
5. Wind forces on tower appurtenances such as ladder, conduits, lights, elevators, etc., shall be
calculated using appropriate force coefficients for these elements.
6. Notation: e = ratio of solid area to gross area of one tower face for segment considered.
3 of 3
Job No Sheet No Rev
AL2430-207 1 B
Job Information
Engineer Checked Approved
Primary 1 SEISMIC-X
Primary 2 SEISMIC-Z
Primary 3 DL
Primary 4 LL
Primary 5 WL-X
Primary 6 WL-Z
Combination 7 COMB 1
Combination 8 COMB 2
Combination 9 COMB 3
Combination 10 COMB 4
Combination 11 COMB5
Combination 12 COMB 6
Combination 13 COMB7
Combination 14 COMB 8
Combination 15 COMB 9
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 1 of 115
Job No Sheet No Rev
AL2430-207 2 B
3D Rendered View
19
25
23
20
21
26
24 15 2
7
22
9 16 4
17
5 8
12
1
14 10
11
18
Y 6
X 13
Z Load 6
3
Node Number
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 2 of 115
Job No Sheet No Rev
AL2430-207 3 B
17
36
16
21
15 39
20
38
37 19
6
22
18 5
23
28
4
32
12
3 11
2 24
29 33
1 10
30
13
25
9
31
14 8
Y 26
X
Z 7 Load 6
27
Beam Number
Nodes
Node X Y Z
(m) (m) (m)
1 0.000 0.000 0.000
2 7.000 0.000 0.000
3 0.000 0.000 2.100
4 7.000 0.000 2.100
5 1.800 0.000 0.000
6 1.800 0.000 2.100
7 5.500 0.000 0.000
8 5.500 0.000 2.100
9 3.200 0.000 0.000
10 3.200 0.000 2.100
11 0.000 0.000 0.700
12 1.800 0.000 0.700
13 0.000 0.000 1.400
14 1.800 0.000 1.400
15 6.800 0.000 0.000
16 6.800 0.000 2.100
17 2.150 0.000 0.000
18 2.150 0.000 2.100
19 6.800 1.950 0.000
20 6.800 1.950 2.100
21 2.150 1.950 0.000
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 3 of 115
Job No Sheet No Rev
AL2430-207 4 B
Nodes Cont...
Node X Y Z
(m) (m) (m)
22 2.150 1.950 2.100
23 3.450 1.950 0.000
24 3.450 1.950 2.100
25 4.650 1.950 0.000
26 4.650 1.950 2.100
29 5.650 1.950 0.000
30 5.650 1.950 2.100
Beams
Beam Node A Node B Length Property β
(m) (degrees)
1 1 5 1.800 2 0
2 5 17 0.350 2 0
3 17 9 1.050 2 0
4 9 7 2.300 2 0
5 7 15 1.300 2 0
6 15 2 0.200 2 0
7 3 6 1.800 2 0
8 6 18 0.350 2 0
9 18 10 1.050 2 0
10 10 8 2.300 2 0
11 8 16 1.300 2 0
12 16 4 0.200 2 0
13 11 12 1.800 2 0
14 13 14 1.800 2 0
15 21 23 1.300 1 0
16 23 25 1.200 1 0
17 25 29 1.000 1 0
18 22 24 1.300 1 0
19 24 26 1.200 1 0
20 26 30 1.000 1 0
21 15 19 1.950 1 90
22 16 20 1.950 1 90
23 17 21 1.950 1 90
24 18 22 1.950 1 90
25 1 11 0.700 2 0
26 11 13 0.700 2 0
27 13 3 0.700 2 0
28 2 4 2.100 2 0
29 5 12 0.700 2 0
30 12 14 0.700 2 0
31 14 6 0.700 2 0
32 7 8 2.100 2 0
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 4 of 115
Job No Sheet No Rev
AL2430-207 5 B
Beams Cont...
Beam Node A Node B Length Property β
(m) (degrees)
33 9 10 2.100 2 0
36 19 20 2.100 1 0
37 21 22 2.100 1 0
38 23 24 2.100 3 0
39 25 26 2.100 3 0
42 29 19 1.150 1 0
43 30 20 1.150 1 0
44 29 30 2.100 3 0
Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 H150X150X7 39.650 562.998 1.62E+3 11.601 STEEL
2 H250X250X9 91.430 3.65E+3 10.7E+3 51.468 STEEL
3 C100X50X5 11.920 26.000 187.999 1.792 STEEL
Materials
Mat Name E ν Density α
(psi) (kg/m3) (/°F)
1 STEEL 29E+6 0.300 7.83E+3 6E -6
2 STAINLESSSTEEL 28E+6 0.300 7.83E+3 10E -6
3 ALUMINUM 10E+6 0.330 2.71E+3 13E -6
4 CONCRETE 3.15E+6 0.170 2.41E+3 5E -6
Supports
Node X Y Z rX rY rZ
(kip/in) (kip/in) (kip/in) (kip-ft/deg) (kip-ft/deg) (kip-ft/deg)
1 Fixed Fixed Fixed - - -
2 Fixed Fixed Fixed - - -
3 Fixed Fixed Fixed - - -
4 Fixed Fixed Fixed - - -
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 5 of 115
Job No Sheet No Rev
AL2430-207 6 B
1 SEISMIC-X
2 SEISMIC-Z
3 DL
4 LL
5 WL-X
6 WL-Z
7 COMB 1 3 DL 1.10
4 LL 1.10
8 COMB 2 3 DL 1.10
4 LL 0.75
5 WL-X 0.75
9 COMB 3 3 DL 1.10
4 LL 0.75
6 WL-Z 0.75
10 COMB 4 3 DL 1.10
5 WL-X 1.00
11 COMB5 3 DL 1.10
6 WL-Z 1.00
12 COMB 6 1 SEISMIC-X 0.70
3 DL 1.10
13 COMB7 1 SEISMIC-X 0.70
3 DL 1.10
4 LL 0.75
14 COMB 8 2 SEISMIC-Z 0.70
3 DL 1.10
15 COMB 9 2 SEISMIC-Z 0.70
3 DL 1.10
4 LL 0.75
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 6 of 115
Job No Sheet No Rev
AL2430-207 7 B
Beam Loads : 3 DL
Beam Type Direction Fa Da Fb Db Ecc.
(m) (m)
13 CON kg GY -410.000 1.550 - - -
14 CON kg GY -410.000 1.550 - - -
32 CON kg GY -1.3E+3 0.500 - - -
33 CON kg GY -1.3E+3 0.500 - - -
Floor Loads : 3 DL
Load Min Ht. Max Ht. Min X Max X Min Y Max Y
(kg/cm2) (m) (m) (m) (m) (m) (m)
-0.010 0.000 3.000 - - - -
-0.009 0.000 1.000 - - - -
Selfweight : 3 DL
Direction Factor
Y -1.000
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 7 of 115
Job No Sheet No Rev
AL2430-207 8 B
Beam Loads : 4 LL
Beam Type Direction Fa Da Fb Db Ecc.
(m) (m)
32 CON kg GY -1.85E+3 0.500 - - -
33 CON kg GY -1.85E+3 0.500 - - -
Floor Loads : 4 LL
Load Min Ht. Max Ht. Min X Max X Min Y Max Y
(kg/cm2) (m) (m) (m) (m) (m) (m)
-0.010 0.000 2.100 - - - -
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 8 of 115
Job No Sheet No Rev
AL2430-207 9 B
67.201 kg/m(GX)
kg/m
67.201 kg/m(GX)
kg/m
38.401 kg/m(GX)
kg/m
38.401 kg/m(GX)
kg/m
43.201 kg/m(GX)
kg/m 67.201 kg/m(GX)
kg/m
38.401
43.201kg/m(GX)
kg/m
kg/m
kg/m(GX)
38.401 kg/m
kg/m(GX) 67.201 kg/m(GX)
kg/m
-4.16e+003 kg
43.201 kg/m(GX)
kg/m 43.201
38.401kg/m(GX)
kg/m
kg/m
kg/m(GX)
38.401 kg/m(GX)
kg/m
18.400 kg/m(GX)
kg/m
43.201 kg/m(GX)
kg/m 69.001 kg/m(GX)
kg/m
43.201 kg/m(GX)
kg/m
69.001 kg/m(GX)
kg/m
96.602 kg/m
kg/m(GX) 473.000 kg 69.001 kg/m(GX)
kg/m
96.602 kg/m
kg/m(GX) 69.001 kg/m(GX)
kg/m
96.602 kg/m(GX)
kg/m
69.001 kg/m(GX)
kg/m 18.400 kg/m(GX)
kg/m
64.402 kg/m(GX)
kg/m 69.001 kg/m(GX)
kg/m
32.201 kg/m
kg/m(GX) 473.000 kg
64.402 kg/m(GX)
kg/m
32.201 kg/m(GX)
kg/m 96.602 kg/m(GX)
kg/m
32.201 kg/m(GX)
kg/m
64.401 kg/m(GX)
kg/m 64.402 kg/m
kg/m(GX) 96.602
96.602 kg/m
kg/m(GX)
kg/m
kg/m(GX)
32.201 kg/m(GX)
kg/m 2*32.201 kg/m
kg/m(GX)
32.201 kg/m(GX)
kg/m
32.201 kg/m(GX)
kg/m 64.401 kg/m(GX)
2*32.201 kg/m(GX)
kg/m kg/m
2*32.201 kg/m(GX)
32.201 kg/m(GX)64.402 kg
kg/m4.16e+003 kg/m(GX)
kg/m
32.201 kg/m
kg/m(GX)
Y 32.201 kg/m(GX)
kg/m
X 2*32.201 kg/m(GX)
kg/m 32.201 kg/m(GX)
kg/m
Z Load 1
32.201 kg/m(GX)
kg/m
32.201 kg/m(GX)
kg/m
Seismic - X
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 9 of 115
Job No Sheet No Rev
AL2430-207 10 B
67.201 kg/m(GX)
kg/m
67.201 kg/m(GX)
kg/m
38.401 kg/m(GX)
kg/m
38.401 kg/m(GX)
kg/m
43.201 kg/m(GX)
kg/m 67.201 kg/m(GX)
kg/m
38.401
43.201kg/m(GX)
kg/m
kg/m
kg/m(GX)
38.401 kg/m
kg/m(GX) 67.201 kg/m(GX)
kg/m
43.201 kg/m(GX)
kg/m 43.201
38.401kg/m(GX)
kg/m
kg/m
kg/m(GX)
38.401 kg/m(GX)
kg/m
18.400 kg/m(GZ)
kg/m
43.201 kg/m(GX)
kg/m 69.001 kg/m(GZ)
kg/m
43.201 kg/m(GX)
kg/m
69.001 kg/m(GZ)
kg/m
473.000 kg 69.001 kg/m(GZ)
kg/m
96.602
96.602 kg/m(GZ)
kg/m
kg/m
kg/m(GZ) -4.16e+003 kgkg/m(GZ)
69.001 kg/m
96.602 kg/m(GZ)
kg/m
69.001 kg/m
kg/m(GZ) 18.400 kg/m(GZ)
kg/m
473.000 kg
64.402 kg/m(GZ)
kg/m 69.001 kg/m(GZ)
kg/m
32.201 kg/m
kg/m(GZ) 64.402 kg/m(GZ)
kg/m
32.201 kg/m(GZ)
kg/m 96.602 kg/m(GZ)
kg/m
32.201 kg/m(GZ)
kg/m
64.401 kg/m(GZ)
kg/m 64.4024.16e+003
kg/m
kg/m(GZ) kg 96.602
96.602 kg/m
kg/m(GZ)
kg/m
kg/m(GZ)
32.201 kg/m(GZ)
kg/m 2*32.201 kg/m
kg/m(GZ)
32.201 kg/m(GZ)
kg/m
32.201 kg/m(GZ)
kg/m 64.401 kg/m(GZ)
2*32.201 kg/m(GZ)
kg/m 2*32.201 kg/m(GZ)
kg/m
kg/m 64.402 kg/m(GZ)
32.201 kg/m(GZ) kg/m
32.201 kg/m
kg/m(GZ)
Y 32.201 kg/m(GZ)
kg/m
X 2*32.201 kg/m(GZ)
kg/m 32.201 kg/m
kg/m(GZ)
Z Load 2
32.201 kg/m(GZ)
kg/m
32.201 kg/m(GZ)
kg/m
Seismic - Z
Y
X
Z Load 3
DL
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 10 of 115
Job No Sheet No Rev
AL2430-207 11 B
Y
X
Z Load 4
LL
122.000 kg
122.000 kg
Y
X 122.000 kg
Z Load 5
122.000 kg
WL-X
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 11 of 115
Job No Sheet No Rev
AL2430-207 12 B
227.000 kg
227.000 kg
227.000 kg
227.000 kg
227.000 kg
227.000 kg
227.000 kg
227.000 kg
Y
X
Z Load 6
WL-Z
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 12 of 115
Job No Sheet No Rev
AL2430-207 13 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 13 of 115
Job No Sheet No Rev
AL2430-207 14 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 14 of 115
Job No Sheet No Rev
AL2430-207 15 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 15 of 115
Job No Sheet No Rev
AL2430-207 16 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 16 of 115
Job No Sheet No Rev
AL2430-207 17 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 17 of 115
Job No Sheet No Rev
AL2430-207 18 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 18 of 115
Job No Sheet No Rev
AL2430-207 19 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 19 of 115
Job No Sheet No Rev
AL2430-207 20 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 20 of 115
Job No Sheet No Rev
AL2430-207 21 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 21 of 115
Job No Sheet No Rev
AL2430-207 22 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 22 of 115
Job No Sheet No Rev
AL2430-207 23 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 23 of 115
Job No Sheet No Rev
AL2430-207 24 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 24 of 115
Job No Sheet No Rev
AL2430-207 25 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 25 of 115
Job No Sheet No Rev
AL2430-207 26 B
X = 147.457 kg
Y = -481.401 kg
Z = -335.242 kg
MX = FREE
MY = FREE
MZ = FREE
X = -147.364 kg
Y = 481.401 kg
Z = -334.317 kg
MX = FREE
MY = FREE
MZ = FREE
X = -575.261 kg
Y = -268.884 kg
Z = -372.536 kg
MX = FREE
Y MY = FREE
X MZ = FREE
Z X = 575.168 kg Load 6
Y = 268.884 kg
Z = -371.905 kg
MX = FREE
MY = FREE
MZ = FREE
Reations
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 26 of 115
Job No Sheet No Rev
AL2430-207 27 B
Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kg) (kg) (kg) (kg-m) (kg-m) (kg-m)
Max FX 3 2:SEISMIC-Z 773.189 695.227 -586.000 0.000 0.000 0.000
Min FX 1 2:SEISMIC-Z -999.921 -869.323 -586.084 0.000 0.000 0.000
Max FY 2 7:COMB 1 -169.384 5.96E+3 38.787 0.000 0.000 0.000
Min FY 2 2:SEISMIC-Z 228.256 -1.43E+3 -563.595 0.000 0.000 0.000
Max FZ 2 13:COMB7 -833.331 5.87E+3 69.223 0.000 0.000 0.000
Min FZ 1 2:SEISMIC-Z -999.921 -869.323 -586.084 0.000 0.000 0.000
Max MX 1 1:SEISMIC-X -733.788 -1.1E+3 -24.118 0.000 0.000 0.000
Min MX 1 1:SEISMIC-X -733.788 -1.1E+3 -24.118 0.000 0.000 0.000
Max MY 1 1:SEISMIC-X -733.788 -1.1E+3 -24.118 0.000 0.000 0.000
Min MY 1 1:SEISMIC-X -733.788 -1.1E+3 -24.118 0.000 0.000 0.000
Max MZ 1 1:SEISMIC-X -733.788 -1.1E+3 -24.118 0.000 0.000 0.000
Min MZ 1 1:SEISMIC-X -733.788 -1.1E+3 -24.118 0.000 0.000 0.000
0.185
0.189
0.16
0.398
0.141 0.245
0.288
0.104
0.203 0.162
0.275
0.505
0.257 0.515
0.226
0.065
0.715
0.228
0.236
0.715 0.465
0.564 0.504
0.0625 0.152
0.495 0.651
0.0619
0.0551
0.0342
0.0627 0.633
0.0549 0.489
0.044
0.433
0.0344
Y
X
Z Load 6
Ratio
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 27 of 115
Job No Sheet No Rev
AL2430-207 28 B
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 H250X250X9 H250X250X9 0.495 1.000 0.495 AISC- H1-3 7 91.430 10.7E+3 3.65E+3 51.100
2 H250X250X9 H250X250X9 0.564 1.000 0.564 AISC- H1-3 7 91.430 10.7E+3 3.65E+3 51.100
3 H250X250X9 H250X250X9 0.715 1.000 0.715 AISC- H2-1 7 91.430 10.7E+3 3.65E+3 51.100
4 H250X250X9 H250X250X9 0.716 1.000 0.716 AISC- H2-1 7 91.430 10.7E+3 3.65E+3 51.100
5 H250X250X9 H250X250X9 0.516 1.000 0.516 AISC- H1-3 13 91.430 10.7E+3 3.65E+3 51.100
6 H250X250X9 H250X250X9 0.274 1.000 0.274 SHEAR -Y 7 91.430 10.7E+3 3.65E+3 51.100
7 H250X250X9 H250X250X9 0.382 1.000 0.382 AISC- H1-3 15 91.430 10.7E+3 3.65E+3 51.100
8 H250X250X9 H250X250X9 0.425 1.000 0.425 AISC- H2-1 15 91.430 10.7E+3 3.65E+3 51.100
9 H250X250X9 H250X250X9 0.532 1.000 0.532 AISC- H2-1 15 91.430 10.7E+3 3.65E+3 51.100
10 H250X250X9 H250X250X9 0.511 1.000 0.511 AISC- H2-1 15 91.430 10.7E+3 3.65E+3 51.100
11 H250X250X9 H250X250X9 0.385 1.000 0.385 AISC- H2-1 15 91.430 10.7E+3 3.65E+3 51.100
12 H250X250X9 H250X250X9 0.194 1.000 0.194 SHEAR -Y 15 91.430 10.7E+3 3.65E+3 51.100
13 H250X250X9 H250X250X9 0.059 1.000 0.059 AISC- H1-3 2 91.430 10.7E+3 3.65E+3 51.100
14 H250X250X9 H250X250X9 0.058 1.000 0.058 AISC- H2-1 2 91.430 10.7E+3 3.65E+3 51.100
15 H150X150X7 H150X150X7 0.145 1.000 0.145 AISC- H1-3 11 39.650 1.62E+3 563.002 11.500
16 H150X150X7 H150X150X7 0.181 1.000 0.181 AISC- H1-3 9 39.650 1.62E+3 563.002 11.500
17 H150X150X7 H150X150X7 0.178 1.000 0.178 AISC- H1-3 9 39.650 1.62E+3 563.002 11.500
18 H150X150X7 H150X150X7 0.186 1.000 0.186 AISC- H2-1 2 39.650 1.62E+3 563.002 11.500
19 H150X150X7 H150X150X7 0.180 1.000 0.180 AISC- H1-3 9 39.650 1.62E+3 563.002 11.500
20 H150X150X7 H150X150X7 0.177 1.000 0.177 AISC- H1-3 9 39.650 1.62E+3 563.002 11.500
21 H150X150X7 H150X150X7 0.389 1.000 0.389 AISC- H1-3 13 39.650 1.62E+3 563.002 11.500
22 H150X150X7 H150X150X7 0.351 1.000 0.351 AISC- H1-3 2 39.650 1.62E+3 563.002 11.500
23 H150X150X7 H150X150X7 0.265 1.000 0.265 AISC- H2-1 11 39.650 1.62E+3 563.002 11.500
24 H150X150X7 H150X150X7 0.366 1.000 0.366 AISC- H1-3 9 39.650 1.62E+3 563.002 11.500
25 H250X250X9 H250X250X9 0.036 1.000 0.036 AISC- H2-1 11 91.430 10.7E+3 3.65E+3 51.100
26 H250X250X9 H250X250X9 0.045 1.000 0.045 AISC- H1-3 15 91.430 10.7E+3 3.65E+3 51.100
27 H250X250X9 H250X250X9 0.036 1.000 0.036 AISC- H1-3 11 91.430 10.7E+3 3.65E+3 51.100
28 H250X250X9 H250X250X9 0.064 1.000 0.064 AISC- H2-1 2 91.430 10.7E+3 3.65E+3 51.100
29 H250X250X9 H250X250X9 0.065 1.000 0.065 AISC- H1-3 2 91.430 10.7E+3 3.65E+3 51.100
30 H250X250X9 H250X250X9 0.064 1.000 0.064 AISC- H1-3 11 91.430 10.7E+3 3.65E+3 51.100
31 H250X250X9 H250X250X9 0.066 1.000 0.066 AISC- H2-1 2 91.430 10.7E+3 3.65E+3 51.100
32 H250X250X9 H250X250X9 0.224 1.000 0.224 SHEAR -Y 13 91.430 10.7E+3 3.65E+3 51.100
33 H250X250X9 H250X250X9 0.185 1.000 0.185 AISC- H2-1 15 91.430 10.7E+3 3.65E+3 51.100
36 H150X150X7 H150X150X7 0.295 1.000 0.295 AISC- H1-3 6 39.650 1.62E+3 563.002 11.500
37 H150X150X7 H150X150X7 0.272 1.000 0.272 AISC- H1-3 11 39.650 1.62E+3 563.002 11.500
38 C100X50X5 C100X50X5 0.289 1.000 0.289 AISC- H1-3 13 11.920 188.001 26.000 1.800
39 C100X50X5 C100X50X5 0.264 1.000 0.264 AISC- H1-3 13 11.920 188.001 26.000 1.800
42 H150X150X7 H150X150X7 0.169 1.000 0.169 AISC- H1-3 13 39.650 1.62E+3 563.002 11.500
43 H150X150X7 H150X150X7 0.185 1.000 0.185 AISC- H1-3 2 39.650 1.62E+3 563.002 11.500
44 C100X50X5 C100X50X5 0.275 1.000 0.275 AISC- H2-1 2 11.920 188.001 26.000 1.800
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 28 of 115
Job No Sheet No Rev
AL2430-207 29 B
M5
M16
M5
M7
M5 M19
M6
M18
M17 M6
M1
M8
M6 M1
M9
M12
M1
M14
M2
M1 M2
M1 M10
M13 M15
M1 M2
M13
M3
M11
M2
M13
M4 M2
Y M11
X
Z M2 Load 6
M11
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 29 of 115
Job No Sheet No Rev
AL2430-207 30 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 230.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 230.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 30 of 115
Job No Sheet No Rev
AL2430-207 31 B
Beam No. 6
Shear Along Y Axis
Shear Along Y Axis Fy (kg ) 5709.02
Critical Loadcase No. 7
Critical Section (cm) 20.00
Beam No. 6
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.72
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 32 of 115
Job No Sheet No Rev
AL2430-207 33 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 33 of 115
Job No Sheet No Rev
AL2430-207 34 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 230.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 230.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 34 of 115
Job No Sheet No Rev
AL2430-207 35 B
Beam No. 12
Shear Along Y Axis
Shear Along Y Axis Fy (kg ) 4047.49
Critical Loadcase No. 15
Critical Section (cm) 20.00
Beam No. 12
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.53
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 36 of 115
Job No Sheet No Rev
AL2430-207 37 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 37 of 115
Job No Sheet No Rev
AL2430-207 38 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 180.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 180.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 180.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 38 of 115
Job No Sheet No Rev
AL2430-207 39 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 28.49
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 35.08
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.75
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 138.19
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 39 of 115
Job No Sheet No Rev
AL2430-207 40 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.05
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 40 of 115
Job No Sheet No Rev
AL2430-207 41 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 41 of 115
Job No Sheet No Rev
AL2430-207 42 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 180.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 180.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 180.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 42 of 115
Job No Sheet No Rev
AL2430-207 43 B
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 43 of 115
Job No Sheet No Rev
AL2430-207 44 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.05
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 44 of 115
Job No Sheet No Rev
AL2430-207 45 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 45 of 115
Job No Sheet No Rev
AL2430-207 46 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 130.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 130.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 46 of 115
Job No Sheet No Rev
AL2430-207 47 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 72.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 30.01
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.86
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 111.28
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 47 of 115
Job No Sheet No Rev
AL2430-207 48 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.18
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 48 of 115
Job No Sheet No Rev
AL2430-207 49 B
f
0.5
=( dw - 2tf ) / tw*fy 111.43
f is less than 380.
Allowable Shear Stress V (MPa)
_allowable
=0.4fy 99.28
Interaction ratio (Along Z Axis)
=Vz / V_allowable 0.01
Status SAFE
Interaction ratio (Along Y Axis)
=Vy / V_allowable 0.06
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 49 of 115
Job No Sheet No Rev
AL2430-207 50 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 130.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 130.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 50 of 115
Job No Sheet No Rev
AL2430-207 51 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 72.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 30.01
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.86
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 111.28
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 51 of 115
Job No Sheet No Rev
AL2430-207 52 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.18
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 52 of 115
Job No Sheet No Rev
AL2430-207 53 B
f
0.5
=( dw - 2tf ) / tw*fy 111.43
f is less than 380.
Allowable Shear Stress V (MPa)
_allowable
=0.4fy 99.28
Interaction ratio (Along Z Axis)
=Vz / V_allowable 0.01
Status SAFE
Interaction ratio (Along Y Axis)
=Vy / V_allowable 0.06
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 53 of 115
Job No Sheet No Rev
AL2430-207 54 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 54 of 115
Job No Sheet No Rev
AL2430-207 55 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 51.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.97
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.81
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 125.43
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 55 of 115
Job No Sheet No Rev
AL2430-207 56 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.39
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 57 of 115
Job No Sheet No Rev
AL2430-207 58 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 58 of 115
Job No Sheet No Rev
AL2430-207 59 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 59 of 115
Job No Sheet No Rev
AL2430-207 60 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 51.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.97
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.81
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 125.43
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 60 of 115
Job No Sheet No Rev
AL2430-207 61 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.34
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 62 of 115
Job No Sheet No Rev
AL2430-207 63 B
Status SAFE
Unsupported Length Along Y Axis Ly_deflection (cm) 195.00
DFF Factor Along Y Axis Dffy 200.00
Allowable Deflection Along Y Axis d (mm)
y_allowable
=Ly_deflection / Dffy 9.75
Actual Delection Along Y Axis dy_actual (mm) 0.02
Critical Loadcase No. 11
Critical Section (cm) 113.75
Interaction Ratio
=dy_actual / dy_allowable 0.00
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 63 of 115
Job No Sheet No Rev
AL2430-207 64 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 64 of 115
Job No Sheet No Rev
AL2430-207 65 B
Beam No. 23
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 65 of 115
Job No Sheet No Rev
AL2430-207 66 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.26
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 66 of 115
Job No Sheet No Rev
AL2430-207 67 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 67 of 115
Job No Sheet No Rev
AL2430-207 68 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 68 of 115
Job No Sheet No Rev
AL2430-207 69 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 69 of 115
Job No Sheet No Rev
AL2430-207 70 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 51.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.97
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.81
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 125.43
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 70 of 115
Job No Sheet No Rev
AL2430-207 71 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.37
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 72 of 115
Job No Sheet No Rev
AL2430-207 73 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 73 of 115
Job No Sheet No Rev
AL2430-207 74 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 70.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 70.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 74 of 115
Job No Sheet No Rev
AL2430-207 75 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 19.41
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 35.57
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.72
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 142.24
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 75 of 115
Job No Sheet No Rev
AL2430-207 76 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.04
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 76 of 115
Job No Sheet No Rev
AL2430-207 77 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 77 of 115
Job No Sheet No Rev
AL2430-207 78 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 78 of 115
Job No Sheet No Rev
AL2430-207 79 B
Beam No. 28
Shear Along Y Axis
Shear Along Y Axis Fy (kg ) 185.06
Critical Loadcase No. 7
Critical Section (cm) 0.00
Beam No. 28
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.04
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 80 of 115
Job No Sheet No Rev
AL2430-207 81 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 81 of 115
Job No Sheet No Rev
AL2430-207 82 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 70.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 70.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 82 of 115
Job No Sheet No Rev
AL2430-207 83 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 19.41
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 35.57
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.72
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 142.24
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 83 of 115
Job No Sheet No Rev
AL2430-207 84 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.06
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 84 of 115
Job No Sheet No Rev
AL2430-207 85 B
f
0.5
=( dw - 2tf ) / tw*fy 148.00
f is less than 380.
Allowable Shear Stress V (MPa)
_allowable
=0.4fy 99.28
Interaction ratio (Along Z Axis)
=Vz / V_allowable 0.01
Status SAFE
Interaction ratio (Along Y Axis)
=Vy / V_allowable 0.04
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 85 of 115
Job No Sheet No Rev
AL2430-207 86 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 86 of 115
Job No Sheet No Rev
AL2430-207 87 B
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 87 of 115
Job No Sheet No Rev
AL2430-207 88 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.19
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 88 of 115
Job No Sheet No Rev
AL2430-207 89 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 89 of 115
Job No Sheet No Rev
AL2430-207 90 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 90 of 115
Job No Sheet No Rev
AL2430-207 91 B
Beam No. 33
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 91 of 115
Job No Sheet No Rev
AL2430-207 92 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.18
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 92 of 115
Job No Sheet No Rev
AL2430-207 93 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 93 of 115
Job No Sheet No Rev
AL2430-207 94 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 94 of 115
Job No Sheet No Rev
AL2430-207 95 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 55.73
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.48
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.82
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 122.93
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 95 of 115
Job No Sheet No Rev
AL2430-207 96 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.28
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 97 of 115
Job No Sheet No Rev
AL2430-207 98 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 98 of 115
Job No Sheet No Rev
AL2430-207 99 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 99 of 115
Job No Sheet No Rev
AL2430-207 100 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 55.73
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.48
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.82
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 122.93
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 100 of 115
Job No Sheet No Rev
AL2430-207 101 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.27
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 102 of 115
Job No Sheet No Rev
AL2430-207 103 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 103 of 115
Job No Sheet No Rev
AL2430-207 104 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 11.92
2
Shear Area Along Z Axis Az (cm ) 0.72
2
Shear Area Along Y Axis Ay (cm ) 4.30
rz (cm) 3.97
ry (cm) 1.48
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 37.60
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 37.60
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 15.64
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 7.79
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 104 of 115
Job No Sheet No Rev
AL2430-207 105 B
Details Of Calculation
Slenderness Checking
Interaction Checking
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 105 of 115
Job No Sheet No Rev
AL2430-207 106 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 106 of 115
Job No Sheet No Rev
AL2430-207 107 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 107 of 115
Job No Sheet No Rev
AL2430-207 108 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 11.92
2
Shear Area Along Z Axis Az (cm ) 0.72
2
Shear Area Along Y Axis Ay (cm ) 4.30
rz (cm) 3.97
ry (cm) 1.48
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 37.60
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 37.60
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 15.64
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 7.79
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 108 of 115
Job No Sheet No Rev
AL2430-207 109 B
Details Of Calculation
Slenderness Checking
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 109 of 115
Job No Sheet No Rev
AL2430-207 110 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.26
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 110 of 115
Job No Sheet No Rev
AL2430-207 111 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 111 of 115
Job No Sheet No Rev
AL2430-207 112 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 11.92
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 11.92
2
Shear Area Along Z Axis Az (cm ) 0.72
2
Shear Area Along Y Axis Ay (cm ) 4.30
rz (cm) 3.97
ry (cm) 1.48
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 37.60
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 37.60
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 15.64
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 7.79
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 112 of 115
Job No Sheet No Rev
AL2430-207 113 B
Beam No. 44
Shear Along Y Axis
Shear Along Y Axis Fy (kg ) 0.12
Critical Loadcase No. 7
Critical Section (cm) 0.00
Beam No. 44
Details Of Calculation
Slenderness Checking
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fcz / fcz_allowable + fcy / fcy_allowable 0.26
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 113 of 115
Job No Sheet No Rev
AL2430-207 114 B
Status SAFE
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 114 of 115
Job No Sheet No Rev
AL2430-207 115 B
Print Time/Date: 03/01/2013 16:11 STAAD.Pro V8i 20.07.05.15 Print Run 115 of 115
Job No Sheet No Rev
AL2430-207 1 B
Job Information
Engineer Checked Approved
Primary 3 DL
Combination 16 COMB 10
3D Rendered View
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 1 of 101
Job No Sheet No Rev
AL2430-207 2 B
33
32
19
31
34
25
23 20
21 35
26
24 152
30
7
22
9 164
29 17 828
5
12
1
14 10
Y 11
X 18
627
Z 13 Load 3
3
Node Number
49
50
44
51
17 36
46
16 53
21
4515 39 52
38 20
37 19 47
6
22
18 5
23 48 43
28
4
32
12
3 11
402 24 42
29 33
1 10
13 30
25
Y 31 9
14
Z
X 26 418
Load 3
27 7
Beam Number
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 2 of 101
Job No Sheet No Rev
AL2430-207 3 B
Nodes
Node X Y Z
(mm) (mm) (mm)
1 0.000 0.000 0.000
2 7E+3 0.000 0.000
3 0.000 0.000 2.1E+3
4 7E+3 0.000 2.1E+3
5 1.8E+3 0.000 0.000
6 1.8E+3 0.000 2.1E+3
7 5.5E+3 0.000 0.000
8 5.5E+3 0.000 2.1E+3
9 3.2E+3 0.000 0.000
10 3.2E+3 0.000 2.1E+3
11 0.000 0.000 700.000
12 1.8E+3 0.000 700.000
13 0.000 0.000 1.4E+3
14 1.8E+3 0.000 1.4E+3
15 6.8E+3 0.000 0.000
16 6.8E+3 0.000 2.1E+3
17 2.15E+3 0.000 0.000
18 2.15E+3 0.000 2.1E+3
19 6.8E+3 1.95E+3 0.000
20 6.8E+3 1.95E+3 2.1E+3
21 2.15E+3 1.95E+3 0.000
22 2.15E+3 1.95E+3 2.1E+3
23 3.45E+3 1.95E+3 0.000
24 3.45E+3 1.95E+3 2.1E+3
25 4.65E+3 1.95E+3 0.000
26 4.65E+3 1.95E+3 2.1E+3
27 1.8E+3 0.000 2.2E+3
28 5.5E+3 0.000 2.2E+3
29 1.8E+3 0.000 -100.000
30 5.5E+3 0.000 -100.000
31 3.65E+3 3.8E+3 2.2E+3
32 3.65E+3 3.8E+3 -100.000
33 3.65E+3 5.8E+3 1.05E+3
34 5.65E+3 1.95E+3 0.000
35 5.65E+3 1.95E+3 2.1E+3
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 3 of 101
Job No Sheet No Rev
AL2430-207 4 B
Beams
Beam Node A Node B Length Property β
(mm) (degrees)
1 1 5 1.8E+3 2 0
2 5 17 349.999 2 0
3 17 9 1.05E+3 2 0
4 9 7 2.3E+3 2 0
5 7 15 1.3E+3 2 0
6 15 2 199.999 2 0
7 3 6 1.8E+3 2 0
8 6 18 349.999 2 0
9 18 10 1.05E+3 2 0
10 10 8 2.3E+3 2 0
11 8 16 1.3E+3 2 0
12 16 4 199.999 2 0
13 11 12 1.8E+3 2 0
14 13 14 1.8E+3 2 0
15 21 23 1.3E+3 1 0
16 23 25 1.2E+3 1 0
17 25 34 999.998 1 0
18 22 24 1.3E+3 1 0
19 24 26 1.2E+3 1 0
20 26 35 999.998 1 0
21 15 19 1.95E+3 1 90
22 16 20 1.95E+3 1 90
23 17 21 1.95E+3 1 90
24 18 22 1.95E+3 1 90
25 1 11 700.000 2 0
26 11 13 699.998 2 0
27 13 3 699.998 2 0
28 2 4 2.1E+3 2 0
29 5 12 700.000 2 0
30 12 14 699.998 2 0
31 14 6 699.998 2 0
32 7 8 2.1E+3 2 0
33 9 10 2.1E+3 2 0
36 19 20 2.1E+3 1 0
37 21 22 2.1E+3 1 0
38 23 24 2.1E+3 3 0
39 25 26 2.1E+3 3 0
40 29 5 100.000 2 0
41 6 27 100.000 2 0
42 8 28 100.000 2 0
43 30 7 100.000 2 0
44 31 32 2.3E+3 4 0
45 32 29 4.23E+3 5 0
46 32 30 4.23E+3 5 0
47 31 28 4.23E+3 5 0
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 4 of 101
Job No Sheet No Rev
AL2430-207 5 B
Beams Cont...
Beam Node A Node B Length Property β
(mm) (degrees)
48 27 31 4.23E+3 5 0
49 32 33 2.31E+3 5 0
50 33 31 2.31E+3 5 0
51 34 19 1.15E+3 1 0
52 35 20 1.15E+3 1 0
53 34 35 2.1E+3 3 0
Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 H150X150X7 39.650 562.998 1.62E+3 11.601 STEEL
2 H250X250X9 91.430 3.65E+3 10.7E+3 51.468 STEEL
3 C100X50X5 11.920 26.000 187.999 1.792 STEEL
4 PIP114.3X5.6 19.120 282.999 282.999 566.391 STEEL
5 Cir 0.79 3.142 0.785 0.785 1.571 STEEL
Materials
Mat Name E ν Density α
(psi) (kg/m3) (/°F)
1 STEEL 29E+6 0.300 7.83E+3 6E -6
2 STAINLESSSTEEL 28E+6 0.300 7.83E+3 10E -6
3 ALUMINUM 10E+6 0.330 2.71E+3 13E -6
4 CONCRETE 3.15E+6 0.170 2.41E+3 5E -6
Supports
Node X Y Z rX rY rZ
(kip/in) (kip/in) (kip/in) (kip-ft/deg) (kip-ft/deg) (kip-ft/deg)
1 Fixed - Fixed - - -
2 - - Fixed - - -
3 Fixed - Fixed - - -
4 - - Fixed - - -
31 Fixed - - - - -
32 Fixed - Fixed - - -
33 Fixed Fixed Fixed Fixed Fixed Fixed
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 5 of 101
Job No Sheet No Rev
AL2430-207 6 B
Releases
Beam ends not shown in this table are fixed in all directions.
Beam Node x y z rx ry rz
3 DL
16 COMB 10 3 DL 1.50
Beam Loads : 3 DL
Beam Type Direction Fa Da Fb Db Ecc.
(mm) (mm)
13 CON kg GY -410.000 1.55E+3 - - -
14 CON kg GY -410.000 1.55E+3 - - -
32 CON kg GY -1.3E+3 499.999 - - -
33 CON kg GY -1.3E+3 499.999 - - -
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 6 of 101
Job No Sheet No Rev
AL2430-207 7 B
Floor Loads : 3 DL
Load Min Ht. Max Ht. Min X Max X Min Y Max Y
(kg/cm2) (mm) (mm) (mm) (mm) (mm) (mm)
-0.010 0.000 2.1E+3 - - - -
-0.009 0.000 999.998 - - - -
Selfweight : 3 DL
Direction Factor
Y -1.000
Y
X
Z Load 3
DL
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 7 of 101
Job No Sheet No Rev
AL2430-207 8 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 8 of 101
Job No Sheet No Rev
AL2430-207 9 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 9 of 101
Job No Sheet No Rev
AL2430-207 10 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 10 of 101
Job No Sheet No Rev
AL2430-207 11 B
X = 0.000 N
Y = 97031.731 N
Z = 7011.753 N
MX = 0.000 kg-m
MY = 0.000 kg-m
MZ = 0.000 kg-m
X = -963.242 N
Y = FREE
M20 N
Z = -7011.753
MX = FREE
MY = FREE
MZ = FREE M5
X = 1247.118 N
Y = M5
FREE M16
M5 Z = FREE
M21
MX = FREE M7
M5 MY =M19
FREE M6
M18 MZ = FREE
M6
M17 M6 M1
X = FREE M8
M6 M1
M9 M14 Y = FREE
M12 N
Z = 525.791
M1 MX = FREE
M14 MY = FREE M2
M1 MZ =M2FREE X = FREE
M1
M13 M10 Y = FREE
M14
M13 M15 Z = -432.578 N
M1 M2 MX = FREE
M13 MY = FREE
757.787 N M3
X =M11
Y M13 M2 MZ = FREE
Y = FREE M4
X M11 N M2
M13
Z Z = 273.227
Load 3
MX = FREE M11 M2
MY = FREE
MZ = FREE X = -1041.663 N
Y = FREE
Z = -366.440 N
MX = FREE
Reations
Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kg) (kg) (kg) (kg-m) (kg-m) (kg-m)
Max FX 31 16:COMB 10 190.756 0.000 0.000 0.000 0.000 0.000
Min FX 3 16:COMB 10 -159.330 0.000 -56.050 0.000 0.000 0.000
Max FY 33 16:COMB 10 0.000 14.8E+3 1.07E+3 0.000 0.000 0.000
Min FY 1 3:DL 77.273 0.000 27.861 0.000 0.000 0.000
Max FZ 33 16:COMB 10 0.000 14.8E+3 1.07E+3 0.000 0.000 0.000
Min FZ 32 16:COMB 10 -147.335 0.000 -1.07E+3 0.000 0.000 0.000
Max MX 1 3:DL 77.273 0.000 27.861 0.000 0.000 0.000
Min MX 1 3:DL 77.273 0.000 27.861 0.000 0.000 0.000
Max MY 1 3:DL 77.273 0.000 27.861 0.000 0.000 0.000
Min MY 1 3:DL 77.273 0.000 27.861 0.000 0.000 0.000
Max MZ 1 3:DL 77.273 0.000 27.861 0.000 0.000 0.000
Min MZ 1 3:DL 77.273 0.000 27.861 0.000 0.000 0.000
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 11 of 101
Job No Sheet No Rev
AL2430-207 12 B
0.174
0.0579
0.101 0.013
0.101 0.141
0.155
0.0732 0.159 0.0576
0.172 0.101
0.0135 0.101 0.0136
0.157
0.0737 0.112
0.159
0.0132
0.125
0.099
0.0136
0.0825 0.109
0.11 0.157
0.0759 0.0904
0.0932 0.116
0.0368 0.0767
0.0253
Y 0.0764 0.0643
X 0.0246 0.0368 0.106
Z Load 3
0.0249 0.0932
Ratio
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 H250X250X9 H250X250X9 0.093 1.000 0.093 AISC- H1-3 16 91.430 10.7E+3 3.65E+3 51.100
2 H250X250X9 H250X250X9 0.110 1.000 0.110 AISC- H1-3 16 91.430 10.7E+3 3.65E+3 51.100
3 H250X250X9 H250X250X9 0.082 1.000 0.082 AISC- H1-3 16 91.430 10.7E+3 3.65E+3 51.100
4 H250X250X9 H250X250X9 0.125 1.000 0.125 AISC- H1-3 16 91.430 10.7E+3 3.65E+3 51.100
5 H250X250X9 H250X250X9 0.112 1.000 0.112 AISC- H2-1 16 91.430 10.7E+3 3.65E+3 51.100
6 H250X250X9 H250X250X9 0.014 1.000 0.014 SHEAR -Y 16 91.430 10.7E+3 3.65E+3 51.100
7 H250X250X9 H250X250X9 0.093 1.000 0.093 AISC- H2-1 16 91.430 10.7E+3 3.65E+3 51.100
8 H250X250X9 H250X250X9 0.106 1.000 0.106 AISC- H1-3 16 91.430 10.7E+3 3.65E+3 51.100
9 H250X250X9 H250X250X9 0.064 1.000 0.064 AISC- H1-3 16 91.430 10.7E+3 3.65E+3 51.100
10 H250X250X9 H250X250X9 0.116 1.000 0.116 AISC- H1-3 16 91.430 10.7E+3 3.65E+3 51.100
11 H250X250X9 H250X250X9 0.109 1.000 0.109 AISC- H2-1 16 91.430 10.7E+3 3.65E+3 51.100
12 H250X250X9 H250X250X9 0.014 1.000 0.014 SHEAR -Y 16 91.430 10.7E+3 3.65E+3 51.100
13 H250X250X9 H250X250X9 0.037 1.000 0.037 SHEAR -Y 16 91.430 10.7E+3 3.65E+3 51.100
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 12 of 101
Job No Sheet No Rev
AL2430-207 13 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 13 of 101
Job No Sheet No Rev
AL2430-207 14 B
M20
M5
M5 M16
M5 M21
M7
M5 M19 M6
M18 M6
M17 M6 M1
M8
M6 M1
M9 M14
M12
M1
M14
M2
M1 M2
M1
M13 M10 M14
M13 M15
M1 M2
M3 M13
M11
Y M13 M2
X M11 M4 M2
Z
M13
Load 3
M11 M2
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 14 of 101
Job No Sheet No Rev
AL2430-207 15 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 230.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 230.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 15 of 101
Job No Sheet No Rev
AL2430-207 16 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 42.98
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 33.91
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.79
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 130.62
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 16 of 101
Job No Sheet No Rev
AL2430-207 17 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.13
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 17 of 101
Job No Sheet No Rev
AL2430-207 18 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 18 of 101
Job No Sheet No Rev
AL2430-207 19 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 230.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 230.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 19 of 101
Job No Sheet No Rev
AL2430-207 20 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 42.98
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 33.91
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.79
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 130.62
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 20 of 101
Job No Sheet No Rev
AL2430-207 21 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.12
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 21 of 101
Job No Sheet No Rev
AL2430-207 22 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 22 of 101
Job No Sheet No Rev
AL2430-207 23 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 180.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 180.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 180.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 23 of 101
Job No Sheet No Rev
AL2430-207 24 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 28.49
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 35.08
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.75
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 138.19
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 24 of 101
Job No Sheet No Rev
AL2430-207 25 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.02
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 25 of 101
Job No Sheet No Rev
AL2430-207 26 B
f
0.5
=( dw - 2tf ) / tw*fy 148.00
f is less than 380.
Allowable Shear Stress V (MPa)
_allowable
=0.4fy 99.28
Interaction ratio (Along Z Axis)
=Vz / V_allowable 0.00
Status SAFE
Interaction ratio (Along Y Axis)
=Vy / V_allowable 0.04
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 26 of 101
Job No Sheet No Rev
AL2430-207 27 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 180.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 180.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 180.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 27 of 101
Job No Sheet No Rev
AL2430-207 28 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 28.49
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 35.08
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.75
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 138.19
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 28 of 101
Job No Sheet No Rev
AL2430-207 29 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.02
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 29 of 101
Job No Sheet No Rev
AL2430-207 30 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 30 of 101
Job No Sheet No Rev
AL2430-207 31 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 130.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 130.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 31 of 101
Job No Sheet No Rev
AL2430-207 32 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 72.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 30.01
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.86
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 111.28
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 32 of 101
Job No Sheet No Rev
AL2430-207 33 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.10
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 33 of 101
Job No Sheet No Rev
AL2430-207 34 B
f
0.5
=( dw - 2tf ) / tw*fy 111.43
f is less than 380.
Allowable Shear Stress V (MPa)
_allowable
=0.4fy 99.28
Interaction ratio (Along Z Axis)
=Vz / V_allowable 0.00
Status SAFE
Interaction ratio (Along Y Axis)
=Vy / V_allowable 0.04
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 34 of 101
Job No Sheet No Rev
AL2430-207 35 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 465.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 130.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 130.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 35 of 101
Job No Sheet No Rev
AL2430-207 36 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 72.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 30.01
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.86
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 111.28
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 36 of 101
Job No Sheet No Rev
AL2430-207 37 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.10
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 37 of 101
Job No Sheet No Rev
AL2430-207 38 B
f
0.5
=( dw - 2tf ) / tw*fy 111.43
f is less than 380.
Allowable Shear Stress V (MPa)
_allowable
=0.4fy 99.28
Interaction ratio (Along Z Axis)
=Vz / V_allowable 0.00
Status SAFE
Interaction ratio (Along Y Axis)
=Vy / V_allowable 0.04
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 38 of 101
Job No Sheet No Rev
AL2430-207 39 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 39 of 101
Job No Sheet No Rev
AL2430-207 40 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 51.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.97
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.81
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 125.43
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 40 of 101
Job No Sheet No Rev
AL2430-207 41 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.16
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 42 of 101
Job No Sheet No Rev
AL2430-207 43 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 43 of 101
Job No Sheet No Rev
AL2430-207 44 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 44 of 101
Job No Sheet No Rev
AL2430-207 45 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 51.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.97
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.81
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 125.43
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 45 of 101
Job No Sheet No Rev
AL2430-207 46 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.16
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 47 of 101
Job No Sheet No Rev
AL2430-207 48 B
Status SAFE
Unsupported Length Along Y Axis Ly_deflection (cm) 195.00
DFF Factor Along Y Axis Dffy 200.00
Allowable Deflection Along Y Axis d (mm)
y_allowable
=Ly_deflection / Dffy 9.75
Actual Delection Along Y Axis dy_actual (mm) 0.00
Critical Loadcase No. 16
Critical Section (cm) 113.75
Interaction Ratio
=dy_actual / dy_allowable 0.00
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 48 of 101
Job No Sheet No Rev
AL2430-207 49 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 49 of 101
Job No Sheet No Rev
AL2430-207 50 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 51.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.97
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.81
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 125.43
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 50 of 101
Job No Sheet No Rev
AL2430-207 51 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.16
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 52 of 101
Job No Sheet No Rev
AL2430-207 53 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 53 of 101
Job No Sheet No Rev
AL2430-207 54 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 195.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 195.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 195.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 54 of 101
Job No Sheet No Rev
AL2430-207 55 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 51.75
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.97
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.81
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 125.43
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 55 of 101
Job No Sheet No Rev
AL2430-207 56 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.16
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 57 of 101
Job No Sheet No Rev
AL2430-207 58 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 58 of 101
Job No Sheet No Rev
AL2430-207 59 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 70.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 70.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 59 of 101
Job No Sheet No Rev
AL2430-207 60 B
Details Of Calculation
Slenderness Checking
T is greater than T
1 2
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 60 of 101
Job No Sheet No Rev
AL2430-207 61 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.03
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 61 of 101
Job No Sheet No Rev
AL2430-207 62 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 62 of 101
Job No Sheet No Rev
AL2430-207 63 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 63 of 101
Job No Sheet No Rev
AL2430-207 64 B
Beam No. 28
Shear Along Y Axis
Shear Along Y Axis Fy (kg ) 0.22
Critical Loadcase No. 16
Critical Section (cm) 0.00
Beam No. 28
Details Of Calculation
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.01
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 64 of 101
Job No Sheet No Rev
AL2430-207 65 B
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 65 of 101
Job No Sheet No Rev
AL2430-207 66 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 66 of 101
Job No Sheet No Rev
AL2430-207 67 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 230.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 70.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 70.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 67 of 101
Job No Sheet No Rev
AL2430-207 68 B
Beam No. 40
Shear Along Y Axis
Shear Along Y Axis Fy (kg ) 17.41
Critical Loadcase No. 16
Critical Section (cm) 0.00
Beam No. 40
Details Of Calculation
T is greater than T
1 2
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 68 of 101
Job No Sheet No Rev
AL2430-207 69 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=ft / ft_allowable + ftz / ftz_allowable + fty / fty_allowable 0.08
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 69 of 101
Job No Sheet No Rev
AL2430-207 70 B
Status SAFE
Unsupported Length Along Y Axis Ly_deflection (cm) 230.00
DFF Factor Along Y Axis Dffy 200.00
Allowable Deflection Along Y Axis d (mm)
y_allowable
=Ly_deflection / Dffy 11.50
Actual Delection Along Y Axis dy_actual (mm) 0.01
Critical Loadcase No. 16
Critical Section (cm) 115.00
Interaction Ratio
=dy_actual / dy_allowable 0.00
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 70 of 101
Job No Sheet No Rev
AL2430-207 71 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 230.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 71 of 101
Job No Sheet No Rev
AL2430-207 72 B
Details Of Calculation
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 33.24
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 34.75
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.76
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 135.86
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 72 of 101
Job No Sheet No Rev
AL2430-207 73 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.10
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 73 of 101
Job No Sheet No Rev
AL2430-207 74 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 74 of 101
Job No Sheet No Rev
AL2430-207 75 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 91.43
2
Shear Area Along Z Axis Az (cm ) 7.79
2
Shear Area Along Y Axis Ay (cm ) 20.56
rz (cm) 10.82
ry (cm) 6.32
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 856.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 856.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 292.00
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 292.00
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 75 of 101
Job No Sheet No Rev
AL2430-207 76 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 33.24
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 34.75
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.76
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 135.86
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 76 of 101
Job No Sheet No Rev
AL2430-207 77 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.07
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 77 of 101
Job No Sheet No Rev
AL2430-207 78 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 78 of 101
Job No Sheet No Rev
AL2430-207 79 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 79 of 101
Job No Sheet No Rev
AL2430-207 80 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 55.73
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.48
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.82
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 122.93
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 80 of 101
Job No Sheet No Rev
AL2430-207 81 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.01
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 82 of 101
Job No Sheet No Rev
AL2430-207 83 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 83 of 101
Job No Sheet No Rev
AL2430-207 84 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 39.65
2
Shear Area Along Z Axis Az (cm ) 3.41
2
Shear Area Along Y Axis Ay (cm ) 9.47
rz (cm) 6.39
ry (cm) 3.77
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 216.00
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 216.00
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 75.07
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 75.07
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 84 of 101
Job No Sheet No Rev
AL2430-207 85 B
Details Of Calculation
Slenderness Checking
E (MPa) 199947.59
Critical ratio L / r (Maximum Of Lz / rz and Ly / ry ) 55.73
Qa ( Due To Web Slenderness ) = Effective Area / Actual Area 1.00
Stress Reduction Factor Qs 1.00
C
c
2 0.5
=( 2 π E / ( Q a Q s fy )) 126.10
L / r is less than C
c
F (ksi)
1a
2
=Q a Q s fy ( 1 - 0.5 * ( L / r * Cc) ) 32.48
F
2a
3
=1.667 + 0.375 * L / r * Cc - 0.125 * ( L / r * Cc ) 1.82
Allowable Axial Compressive Stress f (MPa)
c_allowable
=F1a / F2a 122.93
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 85 of 101
Job No Sheet No Rev
AL2430-207 86 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fc / fc_allowable + fcz / fcz_allowable + fcy / fcy_allowable 0.01
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 87 of 101
Job No Sheet No Rev
AL2430-207 88 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 88 of 101
Job No Sheet No Rev
AL2430-207 89 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 11.92
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 11.92
2
Shear Area Along Z Axis Az (cm ) 0.72
2
Shear Area Along Y Axis Ay (cm ) 4.30
rz (cm) 3.97
ry (cm) 1.48
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 37.60
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 37.60
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 15.64
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 7.79
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 89 of 101
Job No Sheet No Rev
AL2430-207 90 B
Details Of Calculation
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fcz / fcz_allowable + fcy / fcy_allowable 0.17
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 90 of 101
Job No Sheet No Rev
AL2430-207 91 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 91 of 101
Job No Sheet No Rev
AL2430-207 92 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 11.92
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 11.92
2
Shear Area Along Z Axis Az (cm ) 0.72
2
Shear Area Along Y Axis Ay (cm ) 4.30
rz (cm) 3.97
ry (cm) 1.48
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 37.60
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 37.60
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 15.64
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 7.79
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 92 of 101
Job No Sheet No Rev
AL2430-207 93 B
Details Of Calculation
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fcz / fcz_allowable + fcy / fcy_allowable 0.16
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 93 of 101
Job No Sheet No Rev
AL2430-207 94 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 94 of 101
Job No Sheet No Rev
AL2430-207 95 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 19.12
2
Shear Area Along Y Axis Ay (cm ) 9.58
rz (cm) 3.85
ry (cm) 3.85
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 49.52
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 49.52
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 49.52
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 49.52
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 230.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 230.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 230.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 95 of 101
Job No Sheet No Rev
AL2430-207 96 B
Details Of Calculation
Slenderness Checking
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 96 of 101
Job No Sheet No Rev
AL2430-207 97 B
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
E (MPa) 199947.59
Cmz 0.85
Cmy 0.85
f
ez
2 2
=12*π *E / ( 23*Lez / rz ) 41.78
f
ffz
=1 - fc / fez 0.93
2 2
fey=12*π *E / ( 23*Ley / ry ) 41.78
f
ffy
=1 - fc / fey 0.93
Interaction ratio
=fc / fc_allowable + Cmzfcz / ( fffz fcz_allowable ) +
Cmyfcy / ( fffy fcy_allowable ) 0.18
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 97 of 101
Job No Sheet No Rev
AL2430-207 98 B
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 98 of 101
Job No Sheet No Rev
AL2430-207 99 B
Input Parameters
2
Cross Sectional Area Ax (cm ) 11.92
Net section factor 1.00
2
Net Effective Sectional Area Anet (cm ) 11.92
2
Shear Area Along Y Axis Ay (cm ) 4.30
rz (cm) 3.97
ry (cm) 1.48
3
Section Modulus About Z Axis - Tension Edge Stz (cm ) 37.60
3
Section Modulus About Z Axis - Compression Edge Szz (cm ) 37.60
3
Section Modulus About Y Axis - Tension Edge Sty (cm ) 7.79
3
Section Modulus About Y Axis - Compression Edge Syy (cm ) 15.64
Unsupported Length - Z Axis For Slenderness Check Lz (cm) 210.00
Unsupported Length - Y Axis For Slenderness Check Ly (cm) 210.00
Effective Length For Allowable Bending Stress Calculation Unl (cm) 210.00
Yield Stress fy (MPa) 248.00
Ultimate tensile strength fu (MPa) 414.00
Allowable Ratio For Interaction Check 1.00
Design Forces
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 99 of 101
Job No Sheet No Rev
AL2430-207 100 B
Details Of Calculation
Interaction Checking
Factor by which all allowable stresses/capacities to be multiplied 1.00
Interaction ratio
=fcz / fcz_allowable + fcy / fcy_allowable 0.14
Status SAFE
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 100 of 101
Job No Sheet No Rev
AL2430-207 101 B
Print Time/Date: 03/01/2013 16:16 STAAD.Pro V8i 20.07.05.15 Print Run 101 of 101