PSMM
STANDARD METHOD OF MEASUREMENT
OF BUILDING WORKS FOR THE PHILIPPINES
This document is copyrighted to Davis Langdon & Seah Philippines Inc. under Copyright Registration
No. A 2007-1648 dated 22 August 2007. All rights reserved by Davis Langdon & Seah Philippines Inc. No part of
this publication may be reproduced or copied in any form without prior written permission from Davis Langdon &
Seah Philippines Inc.
.
PSMM
STANDARD METHOD OF MEASUREMENT
OF BUILDING WORKS FOR THE PHILIPPINES
This document is copyrighted to Davis Langdon & Seah Philippines Inc. under Copyright Registration
No. A 2007-1648 dated 22 August 2007. All rights reserved by Davis Langdon & Seah Philippines Inc. No part of
this publication may be reproduced or copied in any form without prior written permission from Davis Langdon &
Seah Philippines Inc.
FOREWORD
The Standard Method of Measurement of Building Works for the Philippines was first
published by Davis Langdon & Seah Philippines, Inc. in 1996.
The Standard Method of Measurement of Building Works for the Philippines has been
utilized on a number of major construction and development projects throughout the
Philippines and to that extent has become an industry standard.
Contents
Preface 04200 Unit Masonry 08900 Curtain Walls
General Principles
05100 Structural Steelwork 09100 Suspended Ceilings and Metal Support Systems
01520 Temporary Construction 05500 Metal Fabrications 09205 Metal Lathing
05700 Ornamental Metal (see 05500) 09220 Plaster and Render
02050 Demolition 09250 Gypsum Board
02100 Site Preparation 06100 Rough Carpentry 09300 Tile and Slab Finishes
02152 Shoring 06160 Sheet and Board Linings and Panelling 09550 Wood Flooring
02160 Excavation Support Systems 06200 Finish Carpentry 09650 Resilient Flooring
02200 Earthwork 06400 Architectural Woodwork 09680 Carpet (see 9650)
02250 Diaphragm Walls 06600 Plastic Fabrications (see 05500) 09795 Trims, Division Strips, Nosings and the Like
02361 Steel Sheet Piling 09900 Painting
02362 Precast Concrete Piles 07110 Sheet Membrane and Felt Waterproofing 09950 Paperhanging
02363 Cast in Place Concrete Piles in Driven 07120 Asphalt and Fluid Applied Waterproofing
Casings 07190 Vapor Retarders 10150 Compartments and Cubicles
02364 Isolated Steel Piles 07200 Insulation 10200 Louvers and Vents
02370 Bored Cast in Place Piles 07300 Shingles and Roofing Tiles 10270 Access Flooring
02400 Contractor Designed Piles 07400 Manufactured Roofing and Siding 10430 Exterior Signs
02500 Paving and Surfacing 07510 Sheet Membrane and Felt Roofing 10440 Interior Signs (see 10430)
02605 Utility Trenches and Structures (see 07110) 10615 Demountable Partitions
02660 Water Distribution (see 02700) 07540 Asphalt and Fluid Applied Roofing 10800 Toilet and Bathroom Accessories
02700 Sewerage and Drainage (see 07120)
02830 Fencing and Gates 07900 Sealants 11010 Maintenance Equipment (see 14000)
02840 External Furniture, Fixtures and Fittings 12600 Furniture and Accessories
02900 Soft Landscaping 08100 Metal Doors and Frames 13800 Building Automation Systems (see 16000)
08210 Wood Doors and Frames
03100 Concrete Formwork 08220 Plastic Doors and Frames (see 08100) 14000 Conveying Systems
03200 Concrete Reinforcement 08400 Entrance Screens, Shopfronts and
03230 Stressing Tendons Frameless Glass Doors 15000 Mechanical Installations
03231 Contractor Designed Stressing Tendons 08500 Metal Windows, Rooflights and Screens 15300 Fire Protection
03250 Concrete Accessories 08610 Wood Windows, Rooflights and Screens 15400 Plumbing (see 15300)
03300 Cast in Place Concrete 08630 Plastic Windows, Rooflights and Screens 15440 Plumbing Fixtures
03345 Concrete Finishing (see 8500)
03400 Precast Concrete 08700 Hardware 16000 Electrical Installations
03420 Prestressed Precast Concrete 08800 Glazing
03500 Cementitious Decks and Toppings Index
(a) To produce a method of measurement which is based on local construction techniques and using local terminology
One of the means of achieving these aims was to produce this method of measurement based on the 16 division format used in North America for specifications and other
project information. This is published in various forms by several U.S. and Canadian Organisations and has been widely adopted for use on projects in the Philippines. This
method of measurement is based on the version published as "Masterformat, Master List of Titles and Numbers for the Construction Industry" produced by the Construction
Specifications Institute (Canada) and Construction Specifications Canada. This will make a move towards greater uniformity in the production of information on construction
projects making it more clear and easily understood by everyone involved.
Prior to the introduction of this Standard Method of Measurement for the Philippines (PSMM), methods of measurement from other countries have been used which have not
achieved the criteria above. With the launch of PSMM we hope that estimators will be able to price tenders accurately and with confidence and the administration of contracts
will become easier. The PSMM was first published in March 1997. This second edition has incorporated comments and suggestion made to the first edition and also
incorporates new sections for MEP works.
In an effort to continuously improve this PSMM we welcome comments and suggestion from clients, consultants, contractors and interested bodies.
This PSMM is produced exclusively for use by Davis Langdon & Seah and expressed written permission should be obtained from us should any third party wish to make use of
it.
August 2007
Example: 9.6
02200.1.4.1.1 The term “extra”, “extra for” or “extra over for” preceding any item description
shall mean additional item over and above what is already provided. It is deemed
02200 Earthwork to exclude the price of item for which the extra item will replace.
Excavating
Trenches
Maximum depth < 2.00m
Commencing level stated
8.3
An asterisk within a cross reference represents all entries in the column in which it
appears.
8.4
The digit 0 within a cross reference represents no entries in the column in which it
appears.
3 Leaving parts of
existing structures
temporarily in
position to act as
buttresses
02050/2
Copyright : Davis Langdon & Seah Philippines Inc.
02050 Demolition (continued) 02050/3
2 Removing 1 Structures 1 Dimensioned item 1 Inserting new work, M3 Work in removing D3 Structures include C4 Removing plumbing
description sufficient details stated walls and partitions is walls, partitions, mechanical and electrical
2 Finishes for identification No measured over integral floors, roofs, beams, installations is held to
2 Setting aside doors, windows, screens columns, staircases include removing
3 Coverings m materials to remain and the like and includes and the like, each of sleeves, filling all holes
the property of the for their removal with the which are given and capping or sealing
4 Fixtures and fittings Owner wall or partition separately off ends of pipework to
m² remain
5 Plumbing, 3 Setting aside D4 Finishes include
mechanical and materials for re-use floor, wall, ceiling and C5 Removing finishes is
electrical installations staircase finishes, held to include removing
baseboards and the associated trims, division
like, each of which are strips, nosings and the
given separately like
D5 Coverings include
roof coverings,
waterproofing and the
like, each of which are
given separately
D6 Fixtures and
fittings include doors,
windows, counters,
cabinets, plumbing
fixtures and the like,
each of which are
given separately
3 Filling openings
4 Adapting openings
1 Site clearance 1 Removing trees 1 Girth < 0.60m No M2 Tree girths are C1 Work is held to S2 Filling material
measured at a height of include:- where other than
2 Removing tree stumps 2 Girth in further stages of 1.00m above ground (a) grubbing up roots selected excavated
0.60m (b) disposal of material
M3 Tree stump girths materials off site
are measured at the top (c) filling voids with
selected excavated
M4 Removing trees and material or as
tree stumps girth otherwise described
<0.60m are only
measured where an item
of clearing site
vegetation
(02100.1.3.1.*) is not
measured
02152 Shoring
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
3 Cutting away
existing structures,
details stated
P1 The following information is provided, where available: M1 Steel sheet piling is S1 Kind and quality of
(a) soil investigation results measured in Section materials
(b) ground water level and the date when it was established 02361 - Steel Sheet
(c) location of underground services Piling
CLASSIFICATION TABLE
P1 The following information is provided, where available: M1 Base and sub base C1 Work is held to S1 Kind and quality
(a) soil investigation results courses to roads, include: of materials
(b) ground water level and the date when it was established sidewalks, walkways (a) excavating in any
(c) location of underground services and pavements are ground encountered
measured in Section except as otherwise
02500 - Paving and provided in this
Surfacing section
(b) excavating around
M2 Topsoil filling for existing services
landscaping is (c) temporary support
measured in Section to existing services (d)
02900 - Soft removal of dead
Landscaping services
(e) getting out
excavated materials by
any means necessary
(f) grubbing up old
roots
(g) levelling or
grading bottoms,
trimming to slopes and
trimming to vertical
and sloping sides
(trimming to surfaces
against which concrete
is directly cast is
measured in
accordance with
02200.10.1.*.*)
(h) compacting
bottoms and sides
(i) protection to
sloping surfaces
(j) additional
excavation to provide
working space and
backfilling thereto
CLASSIFICATION TABLE
1 Excavating 1 Topsoil 1 State average depth m² M3 The quantities D1 Excavating to C2 Trenches for
given are the volume reduce levels includes underground services
before excavating and excavating to form are included in the
no allowance is made cuttings and excavating following sections:
3
2 To reduce levels 1 < 0.30m average depth m for subsequent into banks (a) 02605 - Utility
variations to volume Trenches and
2 >0.30m average depth D2 Trenches include Structures
M4 Trenches attached excavation for (b) 02700 - Sewerage
3
3 Basements and the like 1 Maximum depth < 2.00m m 1 Commencing level to pile caps or pits are thickenings to slab on and Drainage
stated measured between the grade, beds and the like
4 Trenches 2 Maximum depth in further pile caps or pits
stages of 2.00m D3 Pits include
5 Pile caps stanchion, column or
pier bases, isolated
6 Pits footings, lift pits and
the like
3
2 Extra over any type 1 Breaking out existing 1 Rock m D4 Rock is defined as
of excavation materials naturally occuring hard
2 Concrete material which
necessitates its removal
2 Breaking up existing 3 Reinforced concrete and m² by means of explosives,
hard surfaces, concrete hollow blocks pneumatic equipment,
thickness stated if wedges or chemical
known 4 Coated macadam or cracking and where its
3
asphalt volume >1.00m
3
3 Excavating for soft m
spots including
disposal and
backfilling with
approved granular
material
3
3 Disposal 1 Topsoil 1 Deposited on site m 1 Specified locations, M5 The quantities C3 The work is held to
details stated given are the volume include for all multi-
3
2 Excavated materials 2 Off site m before excavating and handling to and from
no allowance is made temporary spoil heaps
for subsequent as and if necessary
variations to volume
C4 Disposal is held to
include any type of
excavated material or
broken out materials-
10 Surface treatments 1 Trimming to surfaces 1 Horizontal m² M10 Trimming to D9 Battered faces are
of excavations to surfaces of excavations faces <15º from vertical
receive concrete 2 Sloping <15° is only measured to
those surfaces where
2 Trimming exposed 3 Sloping >15° concrete is cast directly
surfaces of rock to against the surface of
produce fair face 4 Vertical and battered the excavation
CLASSIFICATION TABLE
3
2 Excavating and 1 Thickness of wall, 1 Support fluid, details m M1 The quantities given C2 The following are S2 Details of support
disposal maximum depth and stated are the volume before held to be included: fluid
commencing level excavating and no (a) support fluid
stated allowance is made for (b) subsequent disposal S3 Limitations on
subsequent variations to of support fluid method of disposal
volume (c) disposal of excavated
material off site
(d) excavating in any
ground encountered
except as otherwise
provided in this section
(e) removal of dead
services
(f) getting out excavated
materials by any means
necessary
(g) grubbing up old roots
3
3 Extra over excavation 1 Breaking out existing 1 Rock m D1 Rock is defined as
materials naturally occuring hard
2 Concrete material which
2 Breaking up existing m² necessitates its removal
hard surfaces, 3 Reinforced concrete by means of explosives,
thickness stated if and concrete hollow pneumatic equipment,
known blocks wedges or chemical
cracking and where its
3
4 Coated macadam or volume >1.00m
asphalt
6 Reinforcement kg M5 Reinforcement is
measured in accordance
with Section 03200 -
Concrete Reinforcement
P1 The following information is provided, where available: M1 Steel sheet piling is C1 Work is held to S1 Kind and quality
(a) soil investigation results measured the net include strutting and of materials
(b) ground water level and the date when it was established elevation area (not shoring to steel sheet
(c) location of underground services developed) along the piling during subsequent
(d) any particular requirement regarding phasing or sequence of piling center line of the piling excavation and
foundation work
C2 Withdrawn piles
become the property of
the Contractor unless
otherwise described
C3 Piles described as
withdrawn are held to
include:
(a) cost of withdrawing
(b) allowance for any
credit for withdrawn
piles which become the
property o fthe
Contractor
CLASSIFICATION TABLE
2 Trial piles
P1 The following information is provided, where available: C1 Withdrawn piles S1 Kind and quality
(a) soil investigation results become the property of of materials
(b) ground water level and the date when it was established the Contractor unless
(c) location of underground services otherwise described
(d) any particular requirement regarding phasing or sequence of piling
C2 Piles described as
withdrawn are held to
include:
(a) cost of withdrawing
(b) allowance for any
credit for withdrawn
piles which become the
property o fthe
Contractor
CLASSIFICATION TABLE
3 Trial piles
02364/1
Copyright : Davis Langdon & Seah Philippines Inc.
02364 Isolated Steel Piles (continued) 02364/2
3 Driving piles 1 Cross sectional 1 Commencing level m 1 Battered M1 Measured from the C4 Driving is held to
shape, dimensions stated point in contact with the include:
and weight per meter 2 Subsequently ground to the point when (a) jointing to extend
withdrawing driven piles
(b) driving through any
3 Trial piles ground encountered
(c) driving through rock,
concrete, reinforced
concrete, roots and all
other obstructions
including excavation and
breaking out as necessary
(c) disposal of spoil off
site
CLASSIFICATION TABLE
2 Boring pile holes 1 Nominal diameter 1 Maximum depth and m 1 Support fluid M1 Measured from the C2 Boring pile holes is
stated commencing level point of entry into the held to include:
stated 2 Battered ground to the bottom of (a) boring through any
the bore ground encountered
3 Trial piles (b) boring through rock,
M2 Support fluid is concrete, reinforced
included in the concrete, roots and all
description where other obstructions
designed by the (c) disposal of excavated
Structural Engineer material off site
(d) supports to sides of
excavations including
support fluid
4 Extra over for 1 Formation of 1 Nominal diameter No 1 Trial piles C4 Enlarging bases is
enlarged bases stated held to include:
(a) additional excavation
and disposal
(b) additional concrete
02370/1
Copyright : Davis Langdon & Seah Philippines Inc.
02370 Bored Cast in Place Piles (continued) 02370/2
6 Cutting off tops of 1 Nominal diameter No 1 Trial piles C5 Cutting off tops of
piles stated piles is held to include:
(a) integration of
reinforcement into pile
caps or ground beams
including cleaning,
cutting and bending
(b) disposal
CLASSIFICATION TABLE
2 Contractor designed 1 Load to be carried 1 Commencing level No 1 Designed length M1 Lengths and depths C2 Contractor designed S1 Types of piles,
piles stated and depth of stated are measured to the cut piles are held to include: method of driving or
top of piles below off levels of the piles (a) driving or boring boring and other
commencing level 2 Battered through any ground Structural Engineer's
M2 Lengths are only encountered requirements
3 Trial piles given where designed by (b) driving or boring
the Structural Engineer through rock, concrete,
reinforced concrete, roots
and all other obstructions
including excavation and
breaking out as necessary
(c) disposal of spoil off
site
(d) all work included in
Sections 02361 to 02370
as applicable
02400/1
Copyright : Davis Langdon & Seah Philippines Inc.
02400 Contractor Designed Piles (continued) 02400/2
9 Macadam
P1 The following information is provided, where available: C1 All excavation is held S1 Kind and quality
(a) soil investigation results to include: of materials
(b) ground water level and the date when it was established (a) excavating in any
(c) location of underground services ground encountered
except as otherwise
provided in this section
(b) excavating around
existing services
(c) temporary support to
existing services
(d) removal of dead
services
(e) getting out excavated
materials by any means
necessary
(f) grubbing up old roots
(g) levelling or grading
bottoms, trimming to
slopes and trimming to
vertical and sloping sides
(h) compacting bottoms
and sides
(i) additional excavation
to provide working space
and backfilling thereto
(j) earthwork support
(k) removal of water by
pumping or otherwise
CLASSIFICATION TABLE
1 Excavating trenches 1 Services < 200mm 1 Average depth m 1 Commencing level D1 If the service is laid C2 Work is held to S2 Backfilling
diameter 250mm in a duct it is the include: material where other
2 Curved diameter of the duct (a) backfilling with than selected
2 Services > 200mm 2 and thereafter in which is given selected excavated excavated material
diameter, size stated stages of 250mm material or as otherwise
described
3 More than one (b) disposal of surplus
service, sizes stated excavated material off
site
2 Beds 1 Width and thickness 1 Nominal diameter of m 1 Curved D2 If the service is laid C3 Work is held to
of bed service stated in a duct it is the include formwork
diameter of the duct
3 Beds and haunchings which is given
6 Ducts 1 Nominal size 1 In trenches m 1 Wrapping M1 Ducts are measured C4 Ducts are held to S3 Method of jointing
over all bends, junctions include for: ducts
2 Other, stated 2 Curved ducts and similar fittings (a) all jointing materials
(b) brackets for fixing to
3 Straight ducts set out walls, chamber sides and
to curve the like
(c) concrete thrust blocks
4 Vertical
7 Extra over ducts for 1 Fittings 1 Dimensioned No 1 Wrapping D3 Fittings include C5 Fittings are held to S4 Method of jointing
description bends, junctions, include: to ducts if different to
reducers, connectors, (a) extra joints on ducts general ducts
adaptors and the like (b) concrete thrust blocks
2 Breaking up existing 1 Roads m 1 Reinstating to match M3 Lengths are C7 Removal and S6 Type and thickness
hard surfaces, service existing measured across reinstatement of curbs of surfacing, base and
diameter stated 2 Sidewalks chambers and channels are held to sub-base courses, if
be included known
3 Walkways and
pavements C8 Work is held to
include additional
breaking up and
reinstatement to and
around chambers
P1 The following information is provided, where available: M1 Water distribution is C1 All excavation is held S1 Kind and quality
(a) soil investigation results given under one of the to include: of materials
(b) ground water level and the date when it was established following headings: (a) excavating in any
(c) location of underground services (a) Chilled water system ground encountered
except as otherwise
(b) Domestic water provided in this section
system (b) excavating around
(c) Fire water system existing services
(d) Others, stated (c) temporary support to
existing services
M2 Sewerage and
(d) removal of dead
drainage is given under
services
one of the following
(e) getting out excavated
headings:
materials by any means
(a) Subdrainage system necessary
(b) Storm drainage (f) grubbing up old roots
system (g) levelling or grading
bottoms, trimming to
(c) Sanitary sewerage
slopes and trimming to
(d) Combined vertical and sloping sides
wastewater system (h) compacting bottoms
(e) Others, stated and sides
(i) additional excavation
to provide working space
and backfilling thereto
(j) earthwork support
(k) removal of water by
pumping or otherwise
CLASSIFICATION TABLE
1 Excavating trenches 1 Pipes < 200mm 1 Average depth m 1 Commencing level C2 Work is held to S2 Backfilling
diameter 250mm include: material where other
2 Curved (a) backfilling with than selected
2 Pipes > 200mm 2 and thereafter in selected excavated excavated material
diameter, size stated stages of 250mm material or as otherwise
described
3 More than one pipe, (b) disposal of surplus
sizes stated excavated material off
site
6 Pipes 1 Nominal size 1 In trenches m 1 Wrapping M3 Pipes are measured C4 Pipes are held to S3 Method of jointing
over all bends, junctions include for: pipes
2 Other, stated 2 Vertical and similar fittings (a) all jointing materials
(b) brackets for fixing to
3 Curved pipes walls, manhole sides and
the like
4 Straight pipes set out (c) concrete thrust blocks
to curve
7 Extra over pipes for 1 Fittings 1 Dimensioned No 1 Wrapping M4 Reducing fittings are D1 Fittings include C5 Fittings are held to S4 Method of jointing
description measured extra over the bends, junctions, include: to pipes if different to
largest of the pipes on reducers, connectors, (a) extra joints on pipes general pipes
which they occur and adaptors and the like (b) concrete thrust blocks
include for separate
reducers where a fitting
of the required sizes is
not avavailable
10 Manholes 1 Dimensioned 1 Commencing level of No 1 Backdrops D4 The depth given is C7 Work is held to S5 Backfilling
description and depth excavation stated that from the cover include: material where other
11 Inspection chambers to invert level to the invert level (a) excavation than selected
(b) backfilling with excavated material
12 Septic Tanks selected excavated
material or as otherwise
described
(c) disposal of surplus
excavated material
(d) connections of pipes
(e) all work necessary to
complete the manhole,
chamber or septic tank
13 Extra over any type 1 Breaking out existing 1 Rock m3 M5 The volume of D5 Rock is defined as
of excavation materials breaking out existing naturally occuring hard
2 Concrete materials in trenches is material which
based on the width of the necessitates its removal
3 Reinforced concrete beds in the trenches. by means of explosives,
and concrete hollow Where there are no beds pneumatic equipment,
blocks the width to be taken is wedges or chemical
the nominal size of the cracking and where its
pipe plus 300mm volume >1.00m3
2 Breaking up existing 1 Roads m 1 Reinstating to match M6 Lengths are C8 Removal and S6 Type and thickness
hard surfaces, pipe existing measured across reinstatement of curbs of surfacing, base and
diameter stated 2 Sidewalks manholes and other and channels are held to sub-base courses, if
chambers be included known
3 Paths and pavings
C9 Work is held to
include additional
breaking up and
reinstatement to and
around manholes and
other chambers
CLASSIFICATION TABLE
1 Fencing 1 Dimensioned 1 Type, spacing, height m 1 Fencing set out to a D2 The height of C2 Work is held to S3 Type and size of
description and depth of supports curve but straight fencing is measured include: footings to supports
between posts from the surface of the (a) ends, angles, bends
ground (or other stated and all other changes in S4 Where not
2 Curved fencing, radii base) to the top of the direction supported by footings,
stated infilling or, where there (b) excavating holes for method of fixing and
is no infilling, to the top supports nature of base
3 Fencing to ground wire or rail (c) backfilling with
sloping > 15º from selected excavated S5 Backfilling
the horizontal D3 Curved fencing is material or as otherwise material where other
fencing curved between described than selected
supports (d) disposal of surplus excavated material
excavated material off
site
D7 The depth of
supports is the depth
below the surface of the
ground or other stated
base
C1 Excavation is held to
include:
(a) excavating in any
ground encountered
(b) getting out excavated
materials by any means
necessary
(c) grubbing up old roots
(d) levelling bottoms and
trimming to vertical and
sloping sides
(e) compacting bottoms
and sides
(f) additional excavation
to provide working space
and backfilling thereto
(g) earthwork support
(h) removal of water by
pumping or otherwise
CLASSIFICATION TABLE
1 Fixtures and fittings M1 Work is measured in C2 Work is held to S1 Type and size of
accordance with the include: footings to supports
2 Balustrades following as applicable: (a) excavating holes for
(a) 05500 - Metal supports S2 Where not
3 Railings Fabrications (b) backfilling with supported by footings,
(b) 06400 - Architectural selected excavated method of fixing and
4 Handrails Woodwork material or as otherwise nature of base
(c) 06600 - Plastic described
Fabrications (c) disposal of surplus S3 Backfilling
excavated material off material where other
site than selected
(d) formwork to footings excavated material
(e) all necessary
supports, fixings and
ancillary work
CLASSIFICATION TABLE
4 Seeding 1 Rate stated m² 1 Preparatory work, C3 Seeding and turfing are S2 Method of
details stated held to include work to securing turves
contours and slopes <15°
2 Sloping > 15°
C4 Seeding is held to
include raking or
5 Turfing harrowing in and rolling
7 Trees 1 Botanical name 1 Girth and height No C5 Work is held to S3 Size of pits, holes
include: and trenches,
(a) excavating or forming excavated or formed
pits, holes or trenches
(b) backfilling with S4 Details of any
selected excavated supports, ties, guards,
8 Young nursery stock 1 Height No material or as otherwise wrapping and other
trees described sundry work
(c) disposal of surplus
9 Shrubs excavated material S5 Backfilling
(d) removal of surface material where other
and ground water than selected
(e) watering in excavated material
10 Hedge plants 1 Height stated No (f) initial cutting back
(g) labelling S6 For relocation of
trees, shrubs and
C6 Relocation is held to plants details of:
include maintenance of (a) existing and new
2 Height, spacing, m the trees, shrubs or plants locations
number of rows, and until replanted (b) temporary storage
layout stated including details of
nurseries and duration
of storage
11 Herbaceous plants 1 Size stated No
14 Relocate existing No
shrubs
15 Relocate existing
plants
M9 If the width of a
column is > four times its
thickness it is classified
as a wall
12 Soffits of waffle 1 Size of recesses and 1 Height to soffit m² M11 Measured the flat D9 Soffits of waffle and
slabs profile, centers of < 3.50m area of the soffit with no troughed slabs include
recesses and overall allowance for the profile margins whose width is
13 Soffits of troughed slab thickness stated 2 Thereafter in 1.50m of the recesses < 500mm
slabs stages
16 Sides and soffits of 1 Depth <0.75m 1 Height to soffit m² 4 Curved M12 Edges of suspended D10 Depths of beams S3 Curved beams are
beams and girders < 3.50m slabs associated with and girders attached to separated by those
2 Depth >0.75m attached beams and slabs are measured from curved on plan and
2 Thereafter in 1.50m girders at slab perimeters the soffit of the slab those curved on
stages are included with the elevation
beams and girders D11 Beams and girders
include casings to
structural steel beams
and girders
24 Edges of drop
panels
26 Steps in soffits
33 Corbels
34 Balustrades
35 Counters, shelves
and the like
36 Louvers
38 Moulded edges
39 Ornamental features 1 Grooves 1 Size and shape stated m 1 Curved M15 Ornamental features
to fair faced are only measured to
concrete 2 Rebates formwork to produce a
fair faced finish
3 Drips
5 Recesses
CLASSIFICATION TABLE
1 Bar 1 General 1 Diameter stated and kg 1 Bent to suit curved D1 Where bars are C2 The contractor is to
reinforcement location concrete shown in lengths >12m allow in his rates for any
they are measured in additional laps/slices
2 Links, stirrups and 2 Helical 12m lengths with required to suit his
binders allowance for laps at construction
3 > 12m in length, joints unless methodology
3 Spacers and chairs given in stages of 3m specifically required by
designed by the the Structural Engineer
Structural Engineer to be in other lengths
D2 Bar reinforcement
includes dowel bars
2 Fabric 1 Dimensioned 1 Minimum laps m² 1 Bent to suit curved M5 Fabric is measured C3 Fabric reinforcement
description or weight concrete work the net area covered with is held to include:
per m² and location no allowance for laps (a) notching around
2 In casings to obstructions
structural steel, M6 No deduction is (b) extra material for laps
columns, beams and made for voids (c) spacers and chairs
girders < 1.00m² whether designed by the
Structural Engineer or
not
C4 Fabric in casings to
structural steel, columns,
beams and girders is held
to include welding to the
structural steel member
CLASSIFICATION TABLE
1 Tendons 1 In suspended slabs 1 Number, length and No 1 Curved M1 Lengths are given as C1 Work is held to S2 Details of:
diameter of strand, a straight line between include: (a) ultimate tensile
2 In beams wire or bars which outer faces of anchorages (a) ducts and grouting to strength and jacking
make up the tendons with no allowance for ducts force applied to
undulations along the (b) anchorages including tendons
length of the tendon anchor plates, cones, (b) duct type and size
wedges and the like (c) type of grout
(c) sheathing (d) anchorages
(d) supports to the (e) type of sheathing
material used in the (if any)
formation of ducts
(e) forming and grouting
of air holes
(f) degreasing,
straightening, cutting to
lengths and assembling
tendons and cutting off
ends after tensioning
(g) formwork to form
recesses for anchorages
and filling with grout
CLASSIFICATION TABLE
1 Tendons 1 In suspended slabs 1 Jacking force No M1 Lengths are given as C1 Work is held to
applied, length and a straight line between include:
2 In beams reference outer faces of anchorages (a) ducts and grouting to
with no allowance for ducts
undulations along the (b) anchorages including
length of the tendon anchor plates, cones,
wedges and the like
(c) sheathing
(d) supports to the
material used in the
formation of ducts
(e) forming and grouting
of air holes
(f) degreasing,
straightening, cutting to
lengths and assembling
tendons and cutting off
ends after tensioning
(g) formwork to form
recesses for anchorages
and filling with grout
1 Designed joints 1 Dimensioned m 1 Curved M2 Locations should C1 Waterstops are held S2 Details of
description and follow the classifications to include welded joints (a) fillers and sealants
location 2 Waterstops in Section 03300 - Cast and special fittings at (b) waterstops
in Place Concrete ends, angles and (b) dowel bars (where
3 Sealants intersections measured as part of
the joint)
4 Formwork C2 Cutting and fitting
around reinforcement and
dowel bars are held to be
included
2 Joints not designed by item M3 This item is included C3 Joints are held to
the Structural in the bills of quantities, include:-
Engineer even if joints are (a) formwork
designed by the (b) fillers and sealants
Structural Engineer, so (c) waterstops
that any additional joints (d) dowel bars
required for the (e) additional
Contractor's method of reinforcement required
working can be allowed due to the joint
for (f) all other necessary
work
1 Blinding beds 1 Thickness stated m³ 1 Sloping < 15º C3 Blinding beds are
held to include:
2 Sloping > 15º (a) formwork
(b) casting against face
3 Vertical of excavations
2 Wall footings and the m³ 1 Casting against faces M6 Wall footings are D1 Ground beams
like of excavations measured between include tie beams and
attached column bases the like
3 Column bases,
isolated footings,
pedestals and the like
4 Pile caps
5 Ground beams
6 Mat foundations
7 Columns
m³ M7 If the width of a
8 Casings to structural column is >four times its
steel columns thickness it is classified
as a wall
9 Walls 1 Thickness stated m³ 1 Casting against faces M8 Walls are measured D2 The stated C4 Laying or finishing to
of excavations between columns thickness is that of the falls, currents or cambers
10 Retaining walls general area and are held to be included
M9 The measurement of excludes thickenings,
11 Parapet walls and suspended slabs are taken projections and
planter walls across attached beams recesses
except where beams are
12 Slab on grade, beds 1 Sloping < 15º of a different mix D3 The stated
and the like thickness of waffle
2 Sloping > 15º M10 Waffle and and troughed slabs is
13 Suspended slabs troughed slabs include the overall thickness
3 Casting against faces margins whose width is
14 Waffle slabs of excavations < 500mm. Wider D4 Suspended slabs
margins are included include:
15 Troughed slabs with suspended slabs (a) ramp slabs
(b) landings at floor
16 Machine bases and M11 Cantilevered planter level
plinths boxes are measured in (c) attached drop
item 03300.23 panels
19 Upstand beams
22 Curbs, upstands, m³
zocalos and the like
23 Sunbreakers, fins,
hoods, fascias,
cantilevered planter
boxes and the like
24 Copings
25 Corbels
26 Balustrades
27 Counters, shelves
and the like
28 Louvers
1 Surface finishes to 1 Power floating m² 1 Sloping > 15º C1 Surface finishes are
unset concrete held to include work to
2 Trowelling 2 Curved falls, currents and slopes
< 15º
3 Wood floating 3 Surface treatment,
details stated
4 Broom finishing
2 Surface finishes to set 1 Rubbed finish 1 Floors m² 1 Surface treatment, D1 Beams attached to C2 Floors are held to S2 Description of
concrete details stated ceilings are classified as include work to falls, finish required and
2 Hacking 2 Landings the same height to soffit currents and slopes method of achieving
as the ceiling where the
3 Grinding 3 Walls and columns finish is the same in
nature
4 Sandblasting 4 Treads, risers and
strings
3 Surface treatment,
details stated
P1 A general description of the prestressed precast units and the system and method of tensioning
P2 Particulars of:
(a) Tendons and any preparatory treatment
(b) Whether tendons are to be pre-tensioned or post tensioned or tensioned as the load is applied.
(c) Maturity of concrete before pre-tensioning is released or post-tensioning is applied
(d) Tests to be applied
CLASSIFICATION TABLE
1 Concrete hollow 1 Walls, thickness 1 Built fair and pointed m² 1 Curved, radii stated D1 Walls are held to be C2 Concrete hollow S2 Composition and
block stated one side vertical and of constant block walls are held to mix of mortar
thickness unless include for:
2 Solid concrete block 2 Built fair and pointed otherwise described (a) reinforcement S3 Type of pointing
both sides including dowel bars and where built fair
3 Brick starter bars
(b) filling cavities with S4 For concrete
4 Glass block mortar hollow block walls,
(c) cast in place concrete details of:
stiffeners and lintel (a) reinforcement
beams including (b) concrete stiffeners
formwork and
reinforcement and
precast concrete hollow
beam blocks forming
lintel beams (lintels over
openings are measured
separately.
See 04200.10)
C3 Concrete hollow
block walls and solid
concrete block walls are
held to include:
(a) blocks of special
shape and size at ends,
angles or as otherwise
required
(b) concrete infilling
around inserts and
protrusions or as
otherwise necessary
7 Mesh reinforcement 1 Width 1 Minimum laps m 1 Horizontal M4 Work is measured C5 Work is held to
in joints of block or the net length covered include extra material for
brick walls 2 Vertical with no allowance for laps
laps
3 Curved
8 Damp-proof courses
9 Designed joints 1 Dimensioned m 1 Sealants M5 Joints are only C6 Joints not designed S6 Details of
description measured where designed by the Structural (a) fillers and sealants
2 Curved by the Structural Engineer are held to be (b) ties and fixings
Engineer included
10 Lintels 1 Cast in place 1 Dimensioned m M6 Cast in place lintels D2 Lintels are isolated C7 Cast in place lintels
description are given as composite lintels over openings. are held to include:
items and described Lintel beams in (a) reinforcement
giving the information in concrete hollow block (b) formwork
the following sections as walls are held to be
necessary: included with the walls. C8 Concrete hollow
(a) Section 03100 - See 04200.C2 beam blocks forming
2 Precast concrete 1 Dimensioned m Concrete Formwork lintels are held to
description (b) Section 03200 - include:
Concrete Reinforcement (a) reinforcement
(c) Section 03300 - Cast including dowel bars and
in Place Concrete starter bars
(d) Section 03345 - (b) filling cavities with
Concrete Finishing mortar
3 Concrete hollow 1 Dimensioned m (c) blocks of special
beam blocks description M7 Precast concrete shape and size at ends,
lintels are measured in angles or as otherwise
accordance with Section required
03400 - Precast Concrete (d) temporary support
P1 The following information is shown on drawings which accompany the bills of quantities M1 Work is separated D1 Ordinary bolts are C1 Work is held to S1 Types and grades
(a) the position of the work in relation to other parts of the work and of the proposed buildings into individual structures plain steel bolts used to include: of materials
(b) the types and sizes of structural members and their positions in relation to each other each given under a join steel members (a) all cutting including
(c) details of connections or of the reactions, moments and axial loads at connection points suitable heading to together and include cutting holes and S2 Surface treatments
identify the work high strength bolts perforations off site prior to
(b) notching, drilling and delivery, details stated
D2 Surface treatments countersinking
prior to erection include (c) welds, rivets and S3 Surface treatments
blast cleaning, ordinary bolts with on site prior to
galvanising and associated nuts and erection, details stated
protective painting. washers
Painting after erection
is included in Section
09900 - Painting
CLASSIFICATION TABLE
1 Columns 1 Cross sectional shape 1 Weight per meter kg 1 Curved M2 The mass of
and dimensions members is measured
2 Beams 2 Cambered from their overall lengths
with no deductions for
3 Purlins 3 Tapered splay cuts or mitered
ends or for the mass of
4 Rails 4 Cranked metal removed to form
notches, holes and
5 Bracing 5 Castellated perforations
8 Wires and cables kg M5 Connections, caps C2 Tie rods and the like
and bases are all grouped are held to include:
9 Tie rods and the like together irrespective of (a) threaded ends
the type or of the member (b) nuts, washers and all
10 Connections, caps to which they are other accessories
and bases attached and include (c) drilling or cutting
plates, brackets, cleats, holes in any material
fillets, stiffeners, packing
pieces and gussets
3 Tapered
4 Cranked
11 Fixtures and fittings 1 Dimensioned No 1 Hardware M5 Work contained in C5 Fixtures and fittings
description the fourth column of the are held to include all
2 Glazing beads classification table are ancillary trims, supports,
only included if supplied components and the like
3 Glazing with the component.
Otherwise they are
measured separately
15 Column guards
CLASSIFICATION TABLE
1 Structural members 1 Floor members 1 Cross sectional size m 1 Curved, radii stated M1 Bridging is measured D2 Floor members and C2 Work is held to
over joists flat roof members include gusset plates and
2 Wall or partition include joists and the like
members beams
2 Battens
3 Bearers
4 Packings
5 Fillets
4 To horizontal pipe
casings and false
beams
5 To steel columns
6 To steel beams
7 To suspended
ceilings
8 To bulkheads in
suspended ceilings
CLASSIFICATION TABLE
1 Structural members 1 Floor members 1 Cross sectional size m 1 Curved, radii stated M1 Bridging is measured D2 Floor members and C2 Work is held to
over joists flat roof members include gusset plates and
2 Wall or partition include joists and the like
members beams
2 Battens
3 Bearers
4 Packings
5 Fillets
4 To horizontal pipe
casings and false
beams
5 To steel columns
6 To steel beams
7 To suspended
ceilings
8 To bulkheads in
suspended ceilings
M1 Wood flooring which D1 All sizes are C1 Work is held to S1 Kind and quality
is designed to be a nominal sizes unless include: of materials
finished surface is described as finished (a) all labors, except as
measured in Section sizes otherwise required S2 For solid timber if
09550 - Wood Flooring (b) breather paper rough or dressed and
lining/sheathing if kiln dried
(c) nailing, screwing and
gluing S3 Method of
(d) drilling and plugging jointing or form of
concrete, masonry and construction
the like with hardwood
or proprietary plugs for S4 Method of fixing
fixing with nails or
screws S5 Nature of base,
(e) punching in nail where other than
heads and covering with timber
approved wood filler
(f) countersinking screw S6 Preservatives
and bolt heads and treatments applied as
covering with approved part of the production
wood filler or wood process
pellets
(g) selecting and keeping S7 Surface treatments
clean for clear finishes applied as part of the
(h) notching and holes (i) production process
fair, chamfered, splayed
and rounded edges S8 Size of boards and
(j) ends, shaped ends, thickness of sheets
miters, angles and
intersections
(k) joints including
additional materials
(l) bands and margins set
out to different
arrangement or pattern
(m) providing panels of
the sizes indicated on the
drawings
(n) priming backs,
applying coal tar or
similar protective
coatings prior to fixing
1 Floors 1 Dimensioned m² 1 Curved, radii stated M2 No deduction is D2 Floors include to C2 Floors and roofs are
description made for voids floors within roof held to include laying to
2 Walls and columns 2 Patterned, details < 1.00m² spaces and to landings falls, currents and slopes
stated
3 Roofs M3 Fascias and eaves D3 Walls and columns
soffits made up of solid include:
4 Fascias wood, other than (a) edges of openings
boarding, are measured and recesses in walls
5 Eaves soffits in Section 06200 - Finish and columns
Carpentry (b) attached pipe
6 Vertical pipe casings, casings, false columns
false columns and and casings to steel
casings to steel columns where they are
columns the same in nature
M1 Work is only D1 All sizes are C1 Work is held to S1 Kind and quality
measured independently nominal sizes unless include: of materials
in this section where not described as finished (a) nailing, screwing and
included as part of work sizes gluing S2 For solid timber if
measured in accordance (b) drilling and plugging rough or dressed and
with other sections concrete, masonry and if kiln dried
the like with hardwood
or proprietary plugs for S3 Method of
fixing with nails or jointing or form of
screws construction
(c) punching in nail
heads and covering with S4 Method of fixing
approved wood filler
(d) countersinking screw S5 Nature of base,
and bolt heads and where other than
covering with approved timber
wood filler or wood
pellets S6 Preservatives
(e) selecting and keeping treatments applied as
clean for clear finishes part of the production
(f) notching and holes process
(g) fair edges
(h) ends, shaped ends, S7 Surface treatments
miters, angles and applied as part of the
intersections production process
(i) joints including
additional materials
(j) priming backs,
applying coal tar or
similar protective
coatings prior to fixing
(k) provision for wood
preservative treatment
(l) sundry items of a like
nature
1 Baseboards 1 Cross sectional size m 1 Curved, radii stated M2 Fascias and eaves
and shape soffits made up of wood
2 Dado rails, 2 Built up members, sheet or wood boarding
mouldings and the size of components are measured in Section
like to walls stated 06160 - Sheet and Board
Linings and Panelling
3 Cornices
6 Beads
7 Nosings
8 Cappings
9 Window sills
10 Window boards
11 Window casings
12 Fascias
13 Eaves soffits
15 Duct covers
16 Treads
17 Risers
2 Balustrades 1 Horizontal m 1 Curved, radii stated M2 Metal brackets to C3 Ends, angles, bends
isolated handrails are and all other changes in
3 Railings 2 Sloping measured in one of the direction are held to be
following sections as included
4 Isolated handrails applicable:
(a) Section 05500 - Metal C4 Balustrades include
Fabrications associated handrails
(b) Section 05700 - unless noted otherwise in
Ornamental Metal descriptions
8 Louvers 1 Dimensioned No 1 Hardware M3 Louvers of any D3 Fixtures and fittings C5 Work is held to
description material other than wood include cabinets, include all ancillary
9 Sliding/folding are measured in Section counters, wardrobes, trims, supports,
partitions 10200 - Louvers and shelves and the like components and the like
Vents
10 Fixtures and fittings
M4 Hardware may be
measured separately in
Section 08700 -
Hardware
D4 Beams attached to
ceilings are classified as
the same height to soffit
as the ceiling where the
finish is the same in
nature
13 Linings to gutters
14 Linings to channels
15 Coverings to curbs
16 Linings to 1 Dimensioned No
cesspools, sumps description
and the like
17 Collars around
pipes, railings,
standards and the
like
2 Stone chippings
07120/1
Copyright : Davis Langdon & Seah Philippines Inc.
07120 Asphalt and Fluid Waterproofing (continued) 07120/2
CLASSIFICATION TABLE
D4 Beams attached to
ceilings are classified as
the same height to soffit
as the ceiling where the
finish is the same in
nature
13 Linings to gutters
14 Linings to channels
15 Coverings to curbs
17 Collars around
pipes, railings,
standards and the
like
2 Stone chippings
CLASSIFICATION TABLE
CLASSIFICATION TABLE
1 Floors 1 Thickness m² 1 Across members, D1 Floors include C2 Floors and roofs are
centers of members floors within roof held to include laying to
2 Roofs stated spaces falls, currents and slopes
1 Roof coverings 1 Pitch stated 1 Battens m² 1 Counter battens C2 Coverings are held to S5 Spacing of battens
include: and counter battens
2 Wall coverings 2 Underlay (a) work in forming voids
and holes <0.50m²
3 Curved, radii stated (b) cutting, fitting and
making good around
outlets, pipes and the like
(c) additional battens at
ends, angles and the like
9 Flashings
10 Gutters
11 Filler pieces
CLASSIFICATION TABLE
S3 Nature of base
CLASSIFICATION TABLE
M1 The following are D1 All sizes are C1 Work is held to S1 Kind and quality of
measured in other nominal sizes unless include: materials
sections unless noted described as finished (a) all labors
otherwise: sizes (b) nailing, screwing, S2 For solid timber if
(a) hardware in Section gluing, bolting, fixing rough or dressed and if
08700 - Hardware with brackets, ties and all kiln dried
(b) pointing around other fixings and
frames and the like with fastenings including S3 Method of jointing
sealant in Section 07900 drilling or cutting holes or form of construction
- Sealants in any material
(c) glazing in Section (c) drilling and plugging S4 Method of fixing
08800 - Glazing concrete, masonry and
the like with hardwood S5 Nature of base,
or proprietary plugs for where other than timber
fixing with nails or
screws S6 Preservatives
(d) punching in nail treatments applied as
heads and covering with part of the production
approved wood filler process
(e) countersinking screw
and bolt heads and S7 Surface treatments
covering with approved applied as part of the
wood filler or wood production process
pellets
(f) selecting and keeping
clean for clear finishes
(g) notching and holes
(h) fair, chamfered,
splayed and rounded
edges
(i) ends, shaped ends,
miters, angles and
intersections
(j) joints including
additional materials
(k) bedding in mortar
(l) filling behind frames
with concrete/mortar
including all necessary
formwork
(m) priming backs of
frames, applying coal tar
or similar protective
coatings prior to fixing
(n) provision for wood
preservative treatment
CLASSIFICATION TABLE
3 Door frames
5 Architraves 1 Dimensioned m
description
CLASSIFICATION TABLE
CLASSIFICATION TABLE
M1 The following are D1 All sizes are C1 Work is held to S1 Kind and quality
measured in other nominal sizes unless include: of materials
sections unless noted described as finished (a) all labors
otherwise: sizes (b) nailing, screwing, S2 For solid timber if
(a) hardware in Section gluing, bolting, fixing rough or dressed and
08700 - Hardware with brackets, ties and all if kiln dried
(b) pointing around other fixings and
frames and the like with fastenings including S3 Method of
sealant in Section 07900 drilling or cutting holes jointing or form of
- Sealants in any material construction
(c) glazing in Section (c) drilling and plugging
08800 - Glazing concrete, masonry and S4 Method of fixing
the like with hardwood
or proprietary plugs for S5 Nature of base,
fixing with nails or where other than
screws timber
(d) punching in nail
heads and covering with S6 Preservatives
approved wood filler treatments applied as
(e) countersinking screw part of the production
and bolt heads and process
covering with approved
wood filler or wood S7 Surface treatments
pellets applied as part of the
(f) selecting and keeping production process
clean for clear finishes
(g) notching and holes
(h) fair, chamfered,
splayed and rounded
edges
(i) ends, shaped ends,
miters, angles and
intersections
(j) joints including
additional materials
(k) bedding in mortar
(l) filling behind frames
with concrete/mortar
including all necessary
formwork
(m) priming backs of
frames, applying coal tar
or similar protective
coatings prior to fixing
(n) provision for wood
preservative treatment
4 Screeens
M1 The following are D1 All sizes are C1 Work is held to S1 Kind and quality
measured in other nominal sizes unless include: of materials
sections unless noted described as finished (a) all labors
otherwise: sizes (b) nailing, screwing, S2 For solid timber if
(a) hardware in Section gluing, bolting, fixing rough or dressed and
08700 - Hardware with brackets, ties and all if kiln dried
(b) pointing around other fixings and
frames and the like with fastenings including S3 Method of
sealant in Section 07900 drilling or cutting holes jointing or form of
- Sealants in any material construction
(c) glazing in Section (c) drilling and plugging
08800 - Glazing concrete, masonry and S4 Method of fixing
the like with hardwood
or proprietary plugs for S5 Nature of base,
fixing with nails or where other than
screws timber
(d) punching in nail
heads and covering with S6 Preservatives
approved wood filler treatments applied as
(e) countersinking screw part of the production
and bolt heads and process
covering with approved
wood filler or wood S7 Surface treatments
pellets applied as part of the
(f) selecting and keeping production process
clean for clear finishes
(g) notching and holes
(h) fair, chamfered,
splayed and rounded
edges
(i) ends, shaped ends,
miters, angles and
intersections
(j) joints including
additional materials
(k) bedding in mortar
(l) filling behind frames
with concrete/mortar
including all necessary
formwork
(m) priming backs of
frames, applying coal tar
or similar protective
coatings prior to fixing
(n) provision for wood
preservative treatment
4 Screeens
CLASSIFICATION TABLE
1 Type of item, unit or 1 Nature of base stated No D1 The nature of base C2 Work is held to
set stated is the material of the include fixing to any
main component to other backgrounds as
which it is fixed necessary, even though
the material of the main
component is the only
one stated
1 Glass 1 Thickness stated 1 Panes < 0.10m² m² 1 Irregular shaped M1 Panes of irregular D1 The following glass
panes shape are classified and is enumerated in items
2 Panes 0.10 - 0.50m² measured according to 08800.2-4 below:
2 Decorative finish, the smallest rectangular (a) bent or curved
3 Panes 0.50 - 1.00m² described area from which the pane (b) glass with bevelled
can be obtained edges
4 Panes thereafter in 3 Ground edges
1.00m² stages M2 Glass with a D2 Decorative patterns
4 Polished edges decorative finish is to glass which are not
measured here where it is regular across the whole
5 Sandblasted edges a regular finish across the pane are measured as
whole of the pane extra over the glass in
item 08800.7.2
2 Bent glass 1 Thickness stated 1 Size of pane and No 1 Curved C2 Bevelled edges are
shape where not held to include miters
3 Curved glass rectangular 2 Bent
8 Hacking out existing 1 Type of surround and m 1 Beads for re-use, M4 Hacking out existing
glass and preparing method of glazing details stated glass and preparing
rebates stated together with rebates is measured the
type of glass perimeter of the pane
CLASSIFICATION TABLE
1 Curtain walling 1 Dimensioned m² 1 Sloping M2 Curtain walling is C2 Work is held to S1 Kind and quality
description described as Contractor include: of materials
2 Contractor designed 2 Curved, radii stated designed where the (a) all necessary
curtain walling design is not completed additional work at ends, S2 Method of jointing
3 Flat panes set to by the Owner and is left angles, intersections, or form of
curve to be completed by the abutments and the like construction
Contractor (b) bolts, screws,
3 Extra over for 1 Spandrel panels 1 Dimensioned m² 1 Sloping brackets, ties and all S3 Method of fixing
description M3 Window boards are other fixings, fastenings
2 Curved, radii stated only measured in this and supports including S4 Nature of base
section where part of the drilling or cutting holes
3 Flat panels set to curtain walling system in any material and S5 Bedding, jointing
curve casting into concrete and pointing
(c) trimming around compounds
2 Closers around door m 1 Curved, radii stated projections
and window (d) holes S6 Surface treatments
openings (e) bedding in mortar and finishes applied
(f) sealants and pointing before delivery
3 Closers at floors (g) finishes where part of
the components as
4 Window boards delivered
CLASSIFICATION TABLE
1 Suspended ceilings 1 Dimensioned 1 Depth of suspension m² 1 Height to soffit M1 The following are D1 Work is held to be C1 Work is held to S2 Size and thickness
description <300mm >3.50m above floor measured in other internal unless include: of panels
in stages of 1.50m sections: described as external (a) all jointing materials
2 and thereafter in (a) metal lathing (b) suspension and S3 Thickness of sheet
300mm stages 2 Integral fittings, suspended ceilings D2 Integral fittings framing members linings
details stated (Section 09205 - Metal include special panels, including fixings, trims
Lathing) diffusers, grilles and the and the like S4 Details of framing
3 Curved, radii stated (b) linings to ceilings on like (c) all cutting and fitting and suspension
timber battens or timber over and around system
4 Patterned, details suspended framework obstructions including
stated (timber framework is cutting and fitting up to S5 Method of fixing
measured in Section frames and around pipes,
5 External 06100 - Rough Carpentry brackets and the like S6 Nature of base
and gypsum board lining (d) cutting holes
is measured in Section (e) preparing bases S7 Treatment of joints
09250 - Gypsum Board ) (f) additional supports and surface finish or
2 Bulkheads 1 Dimensioned m 1 Integral fittings, and all other work to materials to be
description details stated M2 No deduction is provide space for received for sheet
3 Light coves made for voids services in the suspended linings
2 Curved, radii stated < 0.50m² ceiling void
(g) additional supports,
3 Patterned, details M3 Integral fittings are trims and accessories as
stated included with the ceiling necessary to fittings,
where part of the partitions, access panels,
4 External suspended ceiling system diffusers, grilles, light
and they also follow a fittings, fixtures, signs
regular layout. Where and the like
4 Extra over for 1 Access panels 1 Dimensioned No 1 External fittings are not part of the (h) sundry items of a like
description suspended ceiling system nature
2 Special panels or do not follow a regular
layout they are measured
3 Diffusers separately in accordance
with 09100.4.*.*.*
4 Grilles
D5 Beams attached to
ceilings are classified as
2 Ceilings and beams m² 1 Height to soffit the same height to soffit
> 3.50m above floor as the ceiling where the
3 Soffits of staircases in stages of 1.50m finish is the same in
and landings nature
2 Curved
3 External
3 External
M1 Work is measured D1 Work in this section C1 Work is held to S1 Kind and quality
that in contact with the includes rigid tile and include: of materials
base and no deduction is slab finishes such as (a) fair joints to all types
made for voids <0.50m² ceramic, mosaic, of work including to S2 Size and thickness
quarry, concrete and existing and shape if other
stone tiles and slabs (b) all jointing materials than rectangular
(c) all fixing materials
D2 Work is held to be including bedding S3 Method of fixing
internal unless mortars, adhesives and
described as external mechanical fixings S4 Nature of base
(d) cleaning, sealing and
D3 The thickness stated polishing S5 Treatment of joints
is the nominal thickness (e) fair edges, angles and
intersections
(f) cutting and fitting into
recessed duct and
manhole covers
(g) dishing to outlets and
gullies
(h) all cutting and fitting
over and around
obstructions including
cutting and fitting up to
frames and around pipes,
brackets and the like
(i) cutting holes
(j) preparing bases
including hacking
concrete to form a key
(k) bonding agents where
necessary or required
(l) sundry items of a like
nature
CLASSIFICATION TABLE
1 Floors 1 Dimensioned m² 1 Floors or roofs M2 Contrasting bands D4 Floors include to C4 Floors and roofs are
description sloping >15º and margins are only floors within roof held to include for laying
2 Landings measured separately in spaces to falls, currents and
2 Curved, radii stated meters where < 300mm slopes < 15º
3 Walls and columns wide. Where bands and D5 Walls and columns
3 Flat rigid tiles or margins are > 300mm include edges of
4 Roofs 2 Contrasting bands m slabs set to curve wide they are measured openings, recesses and
and margins < as general areas of projections on walls and
5 Worktops, vanity 300mm wide, width 4 Patterned, details finishes in square meters columns
tops, seats and the stated stated
like M3 Worktops, vanity D6 Ceilings and beams
5 External tops, seats and the like include edges of
6 Watertank sides and which comprise a single openings, recesses and
bases slab of marble, granite or projections on ceilings
the like are enumerated and beams
5 External
Copyright : Davis Langdon & Seah Philippines Inc.
9 Skirtings 1 Dimensioned m 1 Curved, radii stated C5 Linings to channels
description and coverings to curbs
10 Treads 2 Flat rigid tiles or are held to include
slabs set to curve additional finishes to
11 Risers ends
3 Patterned, details
12 Strings stated
13 Splashbacks 4 External
14 Fascias
15 Linings to channels
16 Coverings to curbs
17 Cappings
18 Cornices
19 Extra over for 1 Special patterns 1 Dimensioned m 1 Curved, radii stated M4 Large feature D8 Special units
description patterns may include units with
2 Special units No 2 Flat rigid tiles or alternatively be measured rounded or other shaped
slabs set to curve net and not extra over edge(s)
3 Patterned, details
stated
4 External
M1 Work is measured D1 Work in this section C1 Work is held to S1 Kind and quality
that in contact with the includes rigid tile and include: of materials
base and no deduction is slab finishes such as (a) fair joints to all types
made for voids <0.50m² ceramic, mosaic, of work including to S2 Size and thickness
quarry, concrete and existing and shape if other
stone tiles and slabs (b) all jointing materials than rectangular
(c) all fixing materials
D2 Work is held to be including bedding S3 Method of fixing
internal unless mortars, adhesives and
described as external mechanical fixings S4 Nature of base
(d) cleaning, sealing and
D3 The thickness stated polishing S5 Treatment of joints
is the nominal thickness (e) fair edges, angles and
intersections
(f) cutting and fitting into
recessed duct and
manhole covers
(g) dishing to outlets and
gullies
(h) all cutting and fitting
over and around
obstructions including
cutting and fitting up to
frames and around pipes,
brackets and the like
(i) cutting holes
(j) preparing bases
including hacking
concrete to form a key
(k) bonding agents where
necessary or required
(l) sundry items of a like
nature
CLASSIFICATION TABLE
1 Floors 1 Dimensioned m² 1 Floors or roofs M2 Contrasting bands D4 Floors include to C4 Floors and roofs are
description sloping >15º and margins are only floors within roof held to include for laying
2 Landings measured separately in spaces to falls, currents and
2 Curved, radii stated meters where < 300mm slopes < 15º
3 Walls and columns wide. Where bands and D5 Walls and columns
3 Flat rigid tiles or margins are > 300mm include edges of
4 Roofs 2 Contrasting bands m slabs set to curve wide they are measured openings, recesses and
and margins < as general areas of projections on walls and
5 Worktops, vanity 300mm wide, width 4 Patterned, details finishes in square meters columns
tops, seats and the stated stated
like M3 Worktops, vanity D6 Ceilings and beams
5 External tops, seats and the like include edges of
6 Watertank sides and which comprise a single openings, recesses and
bases slab of marble, granite or projections on ceilings
the like are enumerated and beams
5 External
Copyright : Davis Langdon & Seah Philippines Inc.
9 Skirtings 1 Dimensioned m 1 Curved, radii stated C5 Linings to channels
description and coverings to curbs
10 Treads 2 Flat rigid tiles or are held to include
slabs set to curve additional finishes to
11 Risers ends
3 Patterned, details
12 Strings stated
13 Splashbacks 4 External
14 Fascias
15 Linings to channels
16 Coverings to curbs
17 Cappings
18 Cornices
19 Extra over for 1 Special patterns 1 Dimensioned m 1 Curved, radii stated M4 Large feature D8 Special units
description patterns may include units with
2 Special units No 2 Flat rigid tiles or alternatively be measured rounded or other shaped
slabs set to curve net and not extra over edge(s)
3 Patterned, details
stated
4 External
M1 Wood flooring which D1 All sizes are C1 Work is held to S1 Kind and quality
is designed to be a nominal sizes unless include: of materials
finished surface is described as finished (a) all labors
measured in this Section. sizes (b) selecting and keeping S2 If kiln dried
Wood flooring designed clean for clear finishes
to be covered is (c) notching and holes S3 Size and thickness
measured in Section (d) fair, chamfered,
06160 - Sheet and Board splayed and rounded S4 Method of
Linings and Panelling edges jointing or form of
(e) ends, shaped ends, construction
M2 No deduction is miters, angles and
made for voids intersections S5 Method of fixing
< 1.00m² (f) joints including
additional materials S6 Nature of base
(g) bands and margins set
out to different S7 Preservatives
arrangement or pattern treatments applied as
(h) working over and part of the production
around obstructions process
(i) providing panels of
the sizes indicated on the S8 Surface treatments
drawings applied as part of the
(j) cork or other production process
compression strips at the
perimeter of work S9 Pattern for block
(k) provision for wood and parquet flooring
preservatives treatment
(l) sundry items of a like
nature
CLASSIFICATION TABLE
C2 Work is held to be
dressed timber
4 Risers
CLASSIFICATION TABLE
1 Floors 1 Dimensioned m² 1 Floors sloping >15º M2 Contrasting D4 Floors include to C2 Floors are held to
description bands and margins floors within roof include for laying to
2 Landings 2 Curved are only measured spaces falls, currents and slopes
separately in meters < 15º
3 Walls and columns 3 Patterned, details stated where < 300mm D5 Walls and columns
wide. Where bands include edges of
4 Worktops, vanity 4 External and margins are > openings, recesses and
tops, seats and the 2 Contrasting bands m 300mm wide they are projections on walls
like and margins < measured as general and columns
300mm wide, width areas of finishes in
stated square meters
8 Strings
9 Linings to channels
10 Coverings to curbs
11 Extra over for 1 Special patterns 1 Dimensioned m 1 Curved M3 Large feature D6 Special units
description patterns may include special units to
2 Special units no 2 Patterned, details stated alternatively be provide rounded
measured net and not edges, angles and
3 External extra over intersections
S2 Method of fixing
4 To staircases and
landings
5 To soffits of
staircases and
landings
6 To worktops, vanity
tops, seats and the
like
M1 The area or girth D1 Work is held to be C1 Work is held to S1 Kind and quality
measured is the area or internal unless include: of materials
girth covered including described as external (a) preparation of
allowances for the extra surfaces S2 Nature of base
girth of edges, D2 Where reference is (b) rubbing down
mouldings, panels, made to painting it is between coats S3 Preparatory work
sinkings, corrugations, held to include clear (c) cutting to line
carvings and the like, finishing and polishing (d) painting to S4 Priming or sealing
except where otherwise corrugated, fluted, coats (No)
stated D3 Preparation includes panelled, carved,
all preparation ornamental or other S5 Undercoats (No)
M2 No deduction is necessary to the surface irregular surfaces
made for voids to receive the paint (e) removing hardware S6 Finishing coats
<0.50m² system described and the like and (No) and surface
including putty, fillers, replacing after painting finish
sealers and the like (f) painting hinges,
fastenings, fixings and S7 Method of
the like application
S8 If moulded,
panelled, corrugated
or carved surfaces are
measured flat this is
stated in the
description
CLASSIFICATION TABLE
9 Baseboards, dado
rails, cornices, coves
and the like
12 Cabinets, wardrobes
and the like
13 Ceilings and beams 1 Girth > 300mm m² 1 Height to soffit D5 Beams attached to
>3.50m above floor ceilings are classified as
14 Soffits of staircases 2 Girth < 300mm m in stages of 1.50m the same height to soffit
and landings as the ceiling where the
2 External finish is the same in
nature
3 On site before fixing
2 Number of coats
16 Balustrades, 1 Plain open type 1 Girth > 300mm m² 1 External M7 Work described as
railings, fences and plain open type is
gates 2 On site before fixing classified according to
2 Girth < 300mm m the size of the individual
members
M8 Work described as
2 Close type m² close type, mesh covered
or ornamental are
3 Mesh covered or measured flat both sides
ornamental
17 Pipes, conduit and 1 Girth > 300mm m² 1 External D6 Pipes, conduit and C4 Pipes, conduit and the
the like the like include cables, like are held to include
2 On site before fixing ducting and trunking work to:
18 Gutters (a) supports
(b) conduit boxes and
other fittings
(c) pipe fittings and
2 Girth < 300mm m accessories
21 Signwriting 1 Dimensioned No
description
CLASSIFICATION TABLE
1 Floors 1 Dimensioned 1 Height of cavity m² 1 Integral fittings, M2 Integral fittings are D2 Integral fittings C2 Work is held to
description stated details stated included with the floor include special panels include for laying to
where part of the raised and the like falls, currents and slopes
2 Sloping > 15º floor system and they < 15º
also follow a regular
3 Patterned, details layout. Where fittings
stated are not part of the raised
floor system or do not
4 External follow a regular layout
they are measured
separately in accordance
2 Downstands 1 Dimensioned m 1 Integral fittings, with 10270.6.*.*.*
description details stated
3 Steps in surfaces
2 Curved, radii stated
3 Patterned, details
stated
4 External
3 External
CLASSIFICATION TABLE
CLASSIFICATION TABLE
4 Three way
intersections
5 Four way
intersections
6 Abutments with
walls and columns
CLASSIFICATION TABLE
S5 Method of fixing
CLASSIFICATION TABLE
S5 Method of fixing
CLASSIFICATION TABLE
8 Cutting holes,
mortices, chases and
the like, grouting
and making good
after installation
9 Providing all
sleeves for fixing
through slabs, walls,
beams and the like
11 Sealing, packing
and fireproofing
where work pass
through slabs, walls,
beams and the like
15 Operating and
maintenance
manuals
17 Instruction of
Owner's
representatives in
operation,
maintenance,
preventive
maintenance and
service of
completed
installation
CLASSIFICATION TABLE
C4 Embedded conduit is
held to include:
(a) casting into concrete,
plaster and toppings
(b) cutting chases in any
materials and making
good
C5 Conduit encased in
concrete is held to
include:
(a) concrete
(b) reinforcement
(c) excavation and
breaking out as
necessary
(d) backfilling with
selected excavated
material or as
otherwise specified
2 Boxes 1 Type and size No 1 External M4 Boxes are only D3 Boxes include pull
measured separately boxes, junction boxes,
where designed by the adaptable boxes, floor
Electrical Engineer. trap boxes, purpose
Where not designed but made boxes,
necessary for the flameproof boxes and
installation they are held all other special boxes
to be included with the
conduit by Rule C3(f)
3 Wireways 1 Type and size 1 Surface fixed m 1 External M5 Wireways, cable D4 Surface fixed C6 Wireways, cable
ladders, underfloor ducts wireways, cable ladders, underfloor ducts
and busducts are ladders and cable and busducts are held to
4 Cable ladders 2 Number of measured over all fittings trays include: include:
compartments (a) joints in the running
(a) fixed to surfaces
which are length
subsequently covered (b) joints to conduit and
5 Underfloor ducts 1 Mounted on concrete m 1 Spring floor by suspended ceilings, distribution boards
floors supports, details raised floors, access (c) joints to fittings
stated panels and the like (d) all labors
2 Embedded in (e) components for
concrete and 2 External (b) fixed in ducts or grounding
concrete toppings pipe chases
(c) generally surface
fixed but embedded
6 Busducts 1 Type, rated capacity m 1 External for short parts of their
and number of lengths as required by
busbars the installation
3 Feeder units
4 Plug in circuit
breakers, ampacity
rating stated
5 Expansion joints
6 Special fittings
7 Connections to
equipment
12 Cables 1 Type and size 1 Drawn into conduits, m 1 External M6 Cable is measured D7 Surface fixed C9 Cables are held to
ducts or wireways the net length following cables include: include:
the shortest distance (a) cables fixed to (a) all labors
2 Drawn into existing between points in straight surfaces which are (b) all joints where not
conduits, ducts or lines except that the subsequently covered designed by the
trunking following allowances are by suspended ceilings, Electrical Engineer but
added for tails: raised floors, access required for the
3 Fixed to cable trays (a) 0.30m on each cable panels and the like installation
or ladders entering lighting fixtures (b) cables generally (c) color coding or other
and accessories surface fixed but identification markings
4 Surface fixed (b) 0.60m on each cable drawn into conduits,
entering equipment and ducts or wireways, C10 Cables drawn into
5 Embedded control gear (i.e. motors, fixed to cable trays or existing conduit, ducts or
transformers, embedded for short wireways are held to
6 Wrapping around panelboards, disconnect parts of their lengths include removing and
pipework or switches, enclosed circuit as required by the replacing existing covers,
equipment breakers and the like). installation inspection lids and the
like
7 Laid in trenches
C11 Embedded cables
are held to include:
(a) casting into concrete,
plaster and toppings
(b) cutting chases in any
materials and making
good
2 Line taps
3 Termination kit
18 Final circuits 1 Cables 1 Lighting points, No 1 Surface fixed M7 Final circuits are D8 Surface fixed C13 Final circuits are
stating whether wall measured on an include: held to include:
2 Conduits or ceiling mounted 2 Embedded enumerated points basis (a) work fixed to (a) providing distribution
and whether centrally where they form part of a surfaces which are diagrams and location
3 Cables and conduits or locally controlled 3 External domestic or similar subsequently covered drawings showing the
simple installation from by suspended ceilings, layout of the points
2 Switch points, stating distribution boards and raised floors, access (b) all conduit fittings
whether one or two the like panels and the like and accessories necessary
way and the number (b) work generally for the installation
of gangs M8 Each lighting point is surface fixed but (c) all cable fittings and
measured as one point embedded for short accessories necessary for
3 Intermediate switch irrespective of the parts of their lengths the installation
points number of lamps as required by the (d) all work to conduits
installation included in Rule C3
4 Socket outlet points M9 Socket outlet points, (e) all work to cables
switch points and the like included in Rule C9.
5 Immersion heater are measured as one
points point irrespective of the C14 Embedded final
number of gangs circuits are held to
6 Cooker points include:
(a) casting into concrete,
7 Fan points plaster and toppings
(b) cutting chases in any
8 Air conditioner materials and making
points good
9 Others, stated
19 Equipment 1 Type and size No 1 External D9 Equipment C15 Work is held to S5 Details of links,
includes motors, include fuses, circuit breakers,
20 Panelboards batteries, transformers (a) all necessary supports gland plates, terminal
and the like (b) connections to boxes and the like
21 Disconnect switches conduit, wireways, cable
trays and cables
22 Enclosed circuit
breakers
23 Lighting fixtures 1 Type and size No 1 External D10 Accessories and C16 Work is held to S6 Lighting fixtures are
field devices include include: to include details of
24 Accessories switches, socket (a) boxes, connector reflectors, shades,
outlets, thermostats, blocks lamps and the like
25 Field devices bell pushes, signal (b) connections to
indicating units, conduit, wireways, cable S7 Accessories are to
clocks, telephones, trays and cable state number of gangs
alarm bells, (c) all necessary ancillary where appropriate
loudspeakers, door work including bushes,
status, smoke nipples, locknuts and the
detectors, heat like
detectors and the like (d) grounding
(e) all supports as
necessary for fixing
28 Cutting holes,
mortices, chases and
the like, grouting
and making good
after installation
29 Providing all
sleeves for fixing
through slabs, walls,
beams and the like
30 Wrapping conduits,
cables or trunking in
felt or similar
protection where
work passes through
slabs, walls, beams
and the like
31 Sealing, packing
and fireproofing
where work passes
through slabs, walls,
beams and the like
35 Operating and
maintenance
manuals
37 Instruction of
Owner's
representatives in
operation,
maintenance,
preventive
maintenance and
service of completed
installation
CLASSIFICATION TABLE
1 Gutters 1 Nominal size or girth m M4 Gutters and pipes C3 Gutters and pipes are
are measured over all held to include:
fittings (a) joints in the running
length
M5 Trenches, chambers (b) joints to fittings,
and beds for ancillaries, fixtures and
underground pipes are equipment
measured in Section (c) all labors including
02605 - Utility Trenches made bends
and Structures (d) supports of any
length or type
(e) sundry items of a like
nature
C5 Pipes <60mm
nominal size are held to
include all fittings
2 To floors
3 To ceilings and
soffits
5 In trenches
D5 Equipment includes
boilers, cisterns,
cylinders, tanks, pumps
and the like
11 Cutting holes,
mortices, chases and
the like, grouting
and making good
after installation
13 Wrapping pipes,
conduit, cables or
trunking in felt or
similar protection
where they pass
through slabs, walls,
beams and the like
19 Operating and
maintenance
manuals
21 Instruction of
Owner’s
representatives in
operation,
maintenance,
preventive
maintenance and
service of completed
installation
5 Shower valves
Access flooring..................................... 10270 Carpentry, sheet and board linings........ 06160 Diaphragm walls................................... 02250
Access hatches, metal............................ 08100.5 Carpentry, architectural woodwork...... 06400 Disconnect switches…………………. 16000.21
Access hatches, wood............................ 08210.4 Carpentry, rough................................... 06100 Division Strips, for finishes................. 09795.2
Alterations............................................ 02050.3 Carpentry, panelling............................. 06160 Doors, wood........................................... 08210
Air terminals…………………………. 16000.15 Carpet.................................................... 09680 Doors, plastic......................................... 08220
Anchor bolts, to structural steel............ 05100.11 Cast in place concrete, to roads etc....... 02500.5 Doors, metal.......................................... 08100
Angle fillets, cement............................. 03500.15 Ceramic tiles.......................................... 09300 Doors, frameless glass.......................... 08400
Asphalt, roofs........................................ 07540 CHB walls............................................. 04200.1 Drainage, underground.......................... 02700
Asphalt, waterproofing.......................... 07120 Cladding, profiled sheets....................... 07400.2 Duct covers, wood................................ 06200.13
Cladding rails, cold rolled metal........ 05100.14 Ducts, for utilities................................. 02605.6
Balustrades, plastic............................... 06600.4 Clearing site vegetation........................ 02100.1.3 Ducts, circular……………………….. 15000.2
Balustrades, plain metal........................ 05500.4 Column guards, plastic.......................... 06600.15 Ducts, flexible……………………….. 15000.3
Balustrades, ornamental metal.............. 05700.4 Column guards, metal............................ 05500.15 Ducts, rectangular……………………. 15000.1
Balustrades, external............................. 02840.2 Compartments...................................... 10150 Dumbwaiters………………………….. 14000.2
Balustrades, wood................................. 06400.2 Concrete, cast in place.......................... 03300
Bar reinforcement................................. 03200.1 Concrete, surface finishes...................... 03345 Earthwork............................................. 02200
Baseboards, plastic................................ 06600.16 Concrete, precast................................... 03400 Eaves soffits, wood sheet and board..... 06160.5
Baseboards, wood.................................. 06200.1 Concrete slabs and tiles......................... 09300 Eaves soffits, solid wood....................... 06200.11
Baseboards, metal.................................. 05500.16 Concrete, filling steel hollow sections.. 05100.16 Electrical installations……………….. 16000
Bathroom accessories............................ 10800 Concrete hollow block walls................. 04200.1 Electrodes……………………………. 16000.16
Battens, wood...................................... . 06100.2.2 Concrete, joints..................................... 03250.1 Elevators……………………………… 14000.3
Boarding, wood..................................... 06160 Concrete, precast post tensioned........... 03420 Enclosed circuit breakers…………….. 16000.22
Bolts, for wood.................................... 06100.5 Conduit………………………………. 16000.1 Equipment, drainage…………………. 02700.9
Boxes, electrical……………………… 16000.2 Conveying systems…………………… 14000 Equipment, electrical…………………. 16000.19
Brick walls........................................... 04200.3 Cornices, wood...................................... 06200.3 Equipment, fire protection…………… 15300.6
Broom finish to concrete...................... 03345.1.4 Cubicles................................................. 10150 Equipment, mechanical……………… 15000.7
Building automation system…………. 13800 Cultivating ground................................. 02900.2 Equipment, maintenance…………….. 11010
Busducts……………………………... 16000.6 Curtain walls......................................... 08900 Escalators……………………………. 14000.4
Cutting and forming openings............... 02050.3.1 Excavating, utility trenches.................. 02605.1
Cables………………………………… 16000.12 Excavating, drainage trenches............... 02700.1
Cable ladders…………………………. 16000.4 Dado rails, wood.................................... 06200.2 Excavating............................................ 02200.1
Cable trays……………………………. 16000.10 Demolition............................................ 02050 Excavation support systems................. 02160
Carpentry, finish carpentry.................... 06200 Demountable partitions......................... 10615 Expansion joint covers, metal.............. 05500.14
Expansion joint covers, plastic.............. 06600.14 Gates...................................................... 02830.4 Inspection chambers, utilities................ 02605.8
Geotextiles, to roads etc........................ 02500.16 Inspection chambers, drainage............. 02700.10
Fabric reinforcement............................. 03200.2 Glass, hacking out existing glass.......... 08800.9 Insulation.............................................. 07200
Fascias, solid wood................................ 06200.10 Glass block walls................................... 04200.4 Insulation, mechanical……………….. 15000.13
Fascias, wood sheet and board.............. 06160.4 Glass...................................................... 08800 Insulation, plumbing………………….. 15300.8
Faucets……………………………….. 15440.2 Gondola………………………………. 11010.1 Joints in concrete................................... 03250.1
Fencing, temporary............................... 01520 Granite................................................... 09300 Joints, sealants....................................... 07900
Fencing, temporary for planting............ 02900.17 Grass turfing.......................................... 02900.5 Joists, wood.......................................... 06100.1
Fencing.................................................. 02830.1 Grass seeding......................................... 02900.4
Field devices………………………….. 16000.25 Gratings, plastic.................................... 06600.13 Ladders, plain metal.............................. 05500.2
Filling existing openings....................... 02050.3.3 Gratings, ornamental metal................... 05700.13 Ladders, ornamental metal.................... 05700.2
Filling, to excavations........................... 02200.5-8 Gratings, plain metal............................. 05500.13 Light coves.......................................…. 09100.3
Filling, base courses to roads etc........... 02500.1-2 Grilles, ornamental metal...................... 05700.12 Lighting fixtures……………………… 16000.23
Finishes, resilient flooring..................... 09650 Grilles, plain metal................................ 05500.12 Lintels................................................… 04200.10
Finishes, paperhanging.......................... 09950 Grilles, plastic....................................... 06600.12 Louvers, wood...................................… 06400.8
Finishes, carpet...................................... 09680 Ground wells…………………………. 16000.17 Louvers, other than wood...................... 10200
Finishes, suspended ceilings.................. 09100 Grounds, wood...................................... 06100.2.1 Louvers, glass........................................ 08800.6
Finishes, tile and slab........................... 09300 Grouting under steel column bases....... 05100.15
Finishes, trims, division strips, nosings 09795 Grounding conductors………………... 16000.14 Manholes.............................................. 02700.9
Finishes, wood flooring........................ 09550 Gutters……………………………….. 15400.1 Marble.................................................... 09300
Finishes, painting................................... 09900 Gypsum board....................................... 09250 Mechanical installations……………… 15000
Fire extinguishers…………………….. 15300.7 Metal fabrications................................. 05500
Fire Protection……………………….. 15300 Handrail brackets, plastic...................... 06600.10 Metal, ornamental................................. 05700
Fixtures and fittings, ornamental metal. 05700.11 Handrail brackets, ornamental metal..... 05700.10 Metal Lathing....................................... 09205
Fixtures and fittings, plain metal........... 05500.11 Handrail brackets, plain metal............... 05500.10 Metal support systems.......................... 09100
Fixtures and fittings, plastic.................. 06600.11 Fixtures, plumbing……………………. 15440.1 Mirrors.................................................. 10800
Fixtures and fittings, wood .................. 06400.10 Handrails, external................................ 02840.4 Mosaic tiles............................................ 09300
Fixtures and fittings, external................ 02840.1 Handrails, ornamental metal.................. 05700.6 Mouldings, wood................................... 06200.2&4
Flush valves………………………….. 15440.3 Handrails, plain metal........................... 05500.6 Moving walks………………………… 14000.5
Folding partitions, wood........................ 06400.9 Handrails, wood.................................... 06400.4 Mulch................................................... 02900.16
Formwork............................................. 03100 Handrails, plastic.................................. 06600.6
Framework, wood................................. 06100.3-4 Hardware............................................... 08700 Non-slip inserts..................................... 09795.4
Framework, metal................................ 09100.5-8 Hedge plants......................................... 02900.10 Nosings, for finishes.............................. 09795.3
Furniture, external................................. 02840 Nosings, wood....................................... 06200.7
Painting lines and symbols................. 02500, 09900 Precast concrete, prestressed................ 03420 Screens, metal....................................... 08500.4
Painting................................................ 09900 Purlins, cold rolled metal....................... 05100.14.1 Sealants.................................................. 07900
Panelboards…………………………. 16000.20 Septic tanks........................................... 02700.11
Panelling, wood..................................... 06160 Quarry tiles............................................ 09300 Sewerage................................................ 02700
Paperhanging......................................... 09950 Sheeting, wood...................................... 06160
Parquet flooring..................................... 09550 Railings, plain metal............................. 05500.5 Shelves, glass......................................... 08800.7
Partitions, sliding/folding, wood........... 06400.9 Railings, ornamental metal.................... 05700.5 Shelves, wood........................................ 06200.12
Paving................................................... 02500 Railings, wood....................................... 06400.3 Shingles................................................. 07300
Piling, bored cast in place...................... 02370 Railings, plastic.................................... 06600.5 Shopfronts............................................. 08400
Piling, contractor designed.................... 02400 Railings, external.................................. 02840.3 Shoring................................................. 02152
Piling, precast concrete......................... 02362 Reinforcement, to concrete.................. 03200 Shotcreting............................................ 02160.3
Piling, steel sheet................................... 02361 Removing existing work........................ 02050.2 Shower heads…………………………. 15440.4
Piling, cast in place in driven casings.... 02363 Removing glass.................................... 08800.9 Shower valves………………………... 15440.5
Piling, isolated steel.............................. 02364 Removing trees...................................... 02100.1.1 Shrubs, relocating................................. 02900.14
Pipe casings, sheet and board............... 06160.6-7 Render................................................... 09220 Shrubs, planting..................................... 02900.9
Pipes, chilled water…………………... 15000.9 Resilient flooring................................... 09650 Signs, door……………………………. 10440.2
Pipes, condensate……………………. 15000.10 Rock anchors......................................... 02160.1 Signwriting............................................ 09900.21
Pipes, condenser water………………. 15000.8 Roller shutters, metal............................. 08100.4 Site preparation..................................... 02100
Pipes, fire protection………………… 15300.1 Roofing, felt.......................................... 07510 Sliding partitions, wood........................ 06400.9
Pipes, for underground drainage........... 02700.6 Roofing, tiles........................................ 07300 Soft landscaping.................................... 02900
Pipes, refrigerant…………………….. 15000.11 Roofing, asphalt.................................... 07540 Soil nails................................................ 02160.2
Pipes, fuel……………………………. 15000.12 Roofing, profiled sheets........................ 07400.1 Staircases, wood.................................... 06400.1
Plants, relocating.................................. 02900.15 Roofing, sheet membrane...................... 07510 Staircases, plain metal........................... 05500.1
Plants.................................................... 02900 Roofing, fluid applied............................ 07540 Staircases, ornamental metal................. 05700.1
Plaster................................................... 09220 Rooflights, plastic.................................. 08630 Stone tiles and slabs.............................. 09300
Plastic fabrications................................ 06600 Rooflights, metal................................... 08500.3 Structural timber................................... 06100.1
Plumbing…………………………….. 15400 Rooflights, wood................................... 08610.3 Structural steelwork.............................. 05100
Plumbing fixtures……………………. 15440 Rubbed finish to concrete...................... 03345.2.1 Suspended ceilings, wood framework... 06100.7
Plywood sheeting.................................. 06160 Suspended ceilings, metal lath.............. 09205.6
Pointing, sealants.................................. 07900 Screeds (toppings)................................. 03500 Suspended ceilings................................ 09100
Portal frames, steel.............................. 05100.7 Screens, entrance.................................. 08400
Power floating to concrete.................... 03345.1.1 Screens, wood........................................ 08610.4 Temporary construction....................... 01520
Precast concrete.................................... 03400 Screens, plastic...................................... 08630 Tendons, Contractor designed............... 03231
The Standard Method of Measurement of Building Works for the Philippines was first
published by Davis Langdon & Seah Philippines, Inc. in 1996.
The Standard Method of Measurement of Building Works for the Philippines has been
utilized on a number of major construction and development projects throughout the
Philippines and to that extent has become an industry standard.
Index
Access flooring..................................... 10270 Carpentry, sheet and board linings........ 06160 Diaphragm walls................................... 02250
Access hatches, metal............................ 08100.5 Carpentry, architectural woodwork...... 06400 Disconnect switches…………………. 16000.21
Access hatches, wood............................ 08210.4 Carpentry, rough................................... 06100 Division Strips, for finishes................. 09795.2
Alterations............................................ 02050.3 Carpentry, panelling............................. 06160 Doors, wood........................................... 08210
Air terminals…………………………. 16000.15 Carpet.................................................... 09680 Doors, plastic......................................... 08220
Anchor bolts, to structural steel............ 05100.11 Cast in place concrete, to roads etc....... 02500.5 Doors, metal.......................................... 08100
Angle fillets, cement............................. 03500.15 Ceramic tiles.......................................... 09300 Doors, frameless glass.......................... 08400
Asphalt, roofs........................................ 07540 CHB walls............................................. 04200.1 Drainage, underground.......................... 02700
Asphalt, waterproofing.......................... 07120 Cladding, profiled sheets....................... 07400.2 Duct covers, wood................................ 06200.13
Cladding rails, cold rolled metal........ 05100.14 Ducts, for utilities................................. 02605.6
Balustrades, plastic............................... 06600.4 Clearing site vegetation........................ 02100.1.3 Ducts, circular……………………….. 15000.2
Balustrades, plain metal........................ 05500.4 Column guards, plastic.......................... 06600.15 Ducts, flexible……………………….. 15000.3
Balustrades, ornamental metal.............. 05700.4 Column guards, metal............................ 05500.15 Ducts, rectangular……………………. 15000.1
Balustrades, external............................. 02840.2 Compartments...................................... 10150 Dumbwaiters………………………….. 14000.2
Balustrades, wood................................. 06400.2 Concrete, cast in place.......................... 03300
Bar reinforcement................................. 03200.1 Concrete, surface finishes...................... 03345 Earthwork............................................. 02200
Baseboards, plastic................................ 06600.16 Concrete, precast................................... 03400 Eaves soffits, wood sheet and board..... 06160.5
Baseboards, wood.................................. 06200.1 Concrete slabs and tiles......................... 09300 Eaves soffits, solid wood....................... 06200.11
Baseboards, metal.................................. 05500.16 Concrete, filling steel hollow sections.. 05100.16 Electrical installations……………….. 16000
Bathroom accessories............................ 10800 Concrete hollow block walls................. 04200.1 Electrodes……………………………. 16000.16
Battens, wood...................................... . 06100.2.2 Concrete, joints..................................... 03250.1 Elevators……………………………… 14000.3
Boarding, wood..................................... 06160 Concrete, precast post tensioned........... 03420 Enclosed circuit breakers…………….. 16000.22
Bolts, for wood.................................... 06100.5 Conduit………………………………. 16000.1 Equipment, drainage…………………. 02700.9
Boxes, electrical……………………… 16000.2 Conveying systems…………………… 14000 Equipment, electrical…………………. 16000.19
Brick walls........................................... 04200.3 Cornices, wood...................................... 06200.3 Equipment, fire protection…………… 15300.6
Broom finish to concrete...................... 03345.1.4 Cubicles................................................. 10150 Equipment, mechanical……………… 15000.7
Building automation system…………. 13800 Cultivating ground................................. 02900.2 Equipment, maintenance…………….. 11010
Busducts……………………………... 16000.6 Curtain walls......................................... 08900 Escalators……………………………. 14000.4
Cutting and forming openings............... 02050.3.1 Excavating, utility trenches.................. 02605.1
Cables………………………………… 16000.12 Excavating, drainage trenches............... 02700.1
Cable ladders…………………………. 16000.4 Dado rails, wood.................................... 06200.2 Excavating............................................ 02200.1
Cable trays……………………………. 16000.10 Demolition............................................ 02050 Excavation support systems................. 02160
Carpentry, finish carpentry.................... 06200 Demountable partitions......................... 10615 Expansion joint covers, metal.............. 05500.14
Expansion joint covers, plastic.............. 06600.14 Gates...................................................... 02830.4 Inspection chambers, utilities................ 02605.8
Geotextiles, to roads etc........................ 02500.16 Inspection chambers, drainage............. 02700.10
Fabric reinforcement............................. 03200.2 Glass, hacking out existing glass.......... 08800.9 Insulation.............................................. 07200
Fascias, solid wood................................ 06200.10 Glass block walls................................... 04200.4 Insulation, mechanical……………….. 15000.13
Fascias, wood sheet and board.............. 06160.4 Glass...................................................... 08800 Insulation, plumbing………………….. 15300.8
Faucets……………………………….. 15440.2 Gondola………………………………. 11010.1 Joints in concrete................................... 03250.1
Fencing, temporary............................... 01520 Granite................................................... 09300 Joints, sealants....................................... 07900
Fencing, temporary for planting............ 02900.17 Grass turfing.......................................... 02900.5 Joists, wood.......................................... 06100.1
Fencing.................................................. 02830.1 Grass seeding......................................... 02900.4
Field devices………………………….. 16000.25 Gratings, plastic.................................... 06600.13 Ladders, plain metal.............................. 05500.2
Filling existing openings....................... 02050.3.3 Gratings, ornamental metal................... 05700.13 Ladders, ornamental metal.................... 05700.2
Filling, to excavations........................... 02200.5-8 Gratings, plain metal............................. 05500.13 Light coves.......................................…. 09100.3
Filling, base courses to roads etc........... 02500.1-2 Grilles, ornamental metal...................... 05700.12 Lighting fixtures……………………… 16000.23
Finishes, resilient flooring..................... 09650 Grilles, plain metal................................ 05500.12 Lintels................................................… 04200.10
Finishes, paperhanging.......................... 09950 Grilles, plastic....................................... 06600.12 Louvers, wood...................................… 06400.8
Finishes, carpet...................................... 09680 Ground wells…………………………. 16000.17 Louvers, other than wood...................... 10200
Finishes, suspended ceilings.................. 09100 Grounds, wood...................................... 06100.2.1 Louvers, glass........................................ 08800.6
Finishes, tile and slab........................... 09300 Grouting under steel column bases....... 05100.15
Finishes, trims, division strips, nosings 09795 Grounding conductors………………... 16000.14 Manholes.............................................. 02700.9
Finishes, wood flooring........................ 09550 Gutters……………………………….. 15400.1 Marble.................................................... 09300
Finishes, painting................................... 09900 Gypsum board....................................... 09250 Mechanical installations……………… 15000
Fire extinguishers…………………….. 15300.7 Metal fabrications................................. 05500
Fire Protection……………………….. 15300 Handrail brackets, plastic...................... 06600.10 Metal, ornamental................................. 05700
Fixtures and fittings, ornamental metal. 05700.11 Handrail brackets, ornamental metal..... 05700.10 Metal Lathing....................................... 09205
Fixtures and fittings, plain metal........... 05500.11 Handrail brackets, plain metal............... 05500.10 Metal support systems.......................... 09100
Fixtures and fittings, plastic.................. 06600.11 Fixtures, plumbing……………………. 15440.1 Mirrors.................................................. 10800
Fixtures and fittings, wood .................. 06400.10 Handrails, external................................ 02840.4 Mosaic tiles............................................ 09300
Fixtures and fittings, external................ 02840.1 Handrails, ornamental metal.................. 05700.6 Mouldings, wood................................... 06200.2&4
Flush valves………………………….. 15440.3 Handrails, plain metal........................... 05500.6 Moving walks………………………… 14000.5
Folding partitions, wood........................ 06400.9 Handrails, wood.................................... 06400.4 Mulch................................................... 02900.16
Formwork............................................. 03100 Handrails, plastic.................................. 06600.6
Framework, wood................................. 06100.3-4 Hardware............................................... 08700 Non-slip inserts..................................... 09795.4
Framework, metal................................ 09100.5-8 Hedge plants......................................... 02900.10 Nosings, for finishes.............................. 09795.3
Furniture, external................................. 02840 Nosings, wood....................................... 06200.7
Painting lines and symbols................. 02500, 09900 Precast concrete, prestressed................ 03420 Screens, metal....................................... 08500.4
Painting................................................ 09900 Purlins, cold rolled metal....................... 05100.14.1 Sealants.................................................. 07900
Panelboards…………………………. 16000.20 Septic tanks........................................... 02700.11
Panelling, wood..................................... 06160 Quarry tiles............................................ 09300 Sewerage................................................ 02700
Paperhanging......................................... 09950 Sheeting, wood...................................... 06160
Parquet flooring..................................... 09550 Railings, plain metal............................. 05500.5 Shelves, glass......................................... 08800.7
Partitions, sliding/folding, wood........... 06400.9 Railings, ornamental metal.................... 05700.5 Shelves, wood........................................ 06200.12
Paving................................................... 02500 Railings, wood....................................... 06400.3 Shingles................................................. 07300
Piling, bored cast in place...................... 02370 Railings, plastic.................................... 06600.5 Shopfronts............................................. 08400
Piling, contractor designed.................... 02400 Railings, external.................................. 02840.3 Shoring................................................. 02152
Piling, precast concrete......................... 02362 Reinforcement, to concrete.................. 03200 Shotcreting............................................ 02160.3
Piling, steel sheet................................... 02361 Removing existing work........................ 02050.2 Shower heads…………………………. 15440.4
Piling, cast in place in driven casings.... 02363 Removing glass.................................... 08800.9 Shower valves………………………... 15440.5
Piling, isolated steel.............................. 02364 Removing trees...................................... 02100.1.1 Shrubs, relocating................................. 02900.14
Pipe casings, sheet and board............... 06160.6-7 Render................................................... 09220 Shrubs, planting..................................... 02900.9
Pipes, chilled water…………………... 15000.9 Resilient flooring................................... 09650 Signs, door……………………………. 10440.2
Pipes, condensate……………………. 15000.10 Rock anchors......................................... 02160.1 Signwriting............................................ 09900.21
Pipes, condenser water………………. 15000.8 Roller shutters, metal............................. 08100.4 Site preparation..................................... 02100
Pipes, fire protection………………… 15300.1 Roofing, felt.......................................... 07510 Sliding partitions, wood........................ 06400.9
Pipes, for underground drainage........... 02700.6 Roofing, tiles........................................ 07300 Soft landscaping.................................... 02900
Pipes, refrigerant…………………….. 15000.11 Roofing, asphalt.................................... 07540 Soil nails................................................ 02160.2
Pipes, fuel……………………………. 15000.12 Roofing, profiled sheets........................ 07400.1 Staircases, wood.................................... 06400.1
Plants, relocating.................................. 02900.15 Roofing, sheet membrane...................... 07510 Staircases, plain metal........................... 05500.1
Plants.................................................... 02900 Roofing, fluid applied............................ 07540 Staircases, ornamental metal................. 05700.1
Plaster................................................... 09220 Rooflights, plastic.................................. 08630 Stone tiles and slabs.............................. 09300
Plastic fabrications................................ 06600 Rooflights, metal................................... 08500.3 Structural timber................................... 06100.1
Plumbing…………………………….. 15400 Rooflights, wood................................... 08610.3 Structural steelwork.............................. 05100
Plumbing fixtures……………………. 15440 Rubbed finish to concrete...................... 03345.2.1 Suspended ceilings, wood framework... 06100.7
Plywood sheeting.................................. 06160 Suspended ceilings, metal lath.............. 09205.6
Pointing, sealants.................................. 07900 Screeds (toppings)................................. 03500 Suspended ceilings................................ 09100
Portal frames, steel.............................. 05100.7 Screens, entrance.................................. 08400
Power floating to concrete.................... 03345.1.1 Screens, wood........................................ 08610.4 Temporary construction....................... 01520
Precast concrete.................................... 03400 Screens, plastic...................................... 08630 Tendons, Contractor designed............... 03231
3 Leaving parts of
existing structures
temporarily in
position to act as
buttresses
02050/2
Copyright : Davis Langdon & Seah Philippines Inc.
02050 Demolition (continued) 02050/3
2 Removing 1 Structures 1 Dimensioned item 1 Inserting new work, M3 Work in removing D3 Structures include C4 Removing plumbing
description sufficient details stated walls and partitions is walls, partitions, mechanical and electrical
2 Finishes for identification No measured over integral floors, roofs, beams, installations is held to
2 Setting aside doors, windows, screens columns, staircases include removing
3 Coverings m materials to remain and the like and includes and the like, each of sleeves, filling all holes
the property of the for their removal with the which are given and capping or sealing
4 Fixtures and fittings Owner wall or partition separately off ends of pipework to
m² remain
5 Plumbing, 3 Setting aside D4 Finishes include
mechanical and materials for re-use floor, wall, ceiling and C5 Removing finishes is
electrical installations staircase finishes, held to include removing
baseboards and the associated trims, division
like, each of which are strips, nosings and the
given separately like
D5 Coverings include
roof coverings,
waterproofing and the
like, each of which are
given separately
D6 Fixtures and
fittings include doors,
windows, counters,
cabinets, plumbing
fixtures and the like,
each of which are
given separately
3 Filling openings
4 Adapting openings
1 Site clearance 1 Removing trees 1 Girth < 0.60m No M2 Tree girths are C1 Work is held to S2 Filling material
measured at a height of include:- where other than
2 Removing tree stumps 2 Girth in further stages of 1.00m above ground (a) grubbing up roots selected excavated
0.60m (b) disposal of material
M3 Tree stump girths materials off site
are measured at the top (c) filling voids with
selected excavated
M4 Removing trees and material or as
tree stumps girth otherwise described
<0.60m are only
measured where an item
of clearing site
vegetation
(02100.1.3.1.*) is not
measured
02152 Shoring
INFORMATION TO BE PROVIDED MEASUREMENT DEFINITION RULES COVERAGE RULES SUPPLEMENTARY
RULES INFORMATION
3 Cutting away
existing structures,
details stated
P1 The following information is provided, where available: M1 Steel sheet piling is S1 Kind and quality of
(a) soil investigation results measured in Section materials
(b) ground water level and the date when it was established 02361 - Steel Sheet
(c) location of underground services Piling
CLASSIFICATION TABLE
P1 The following information is provided, where available: M1 Base and sub base C1 Work is held to S1 Kind and quality
(a) soil investigation results courses to roads, include: of materials
(b) ground water level and the date when it was established sidewalks, walkways (a) excavating in any
(c) location of underground services and pavements are ground encountered
measured in Section except as otherwise
02500 - Paving and provided in this
Surfacing section
(b) excavating around
M2 Topsoil filling for existing services
landscaping is (c) temporary support
measured in Section to existing services (d)
02900 - Soft removal of dead
Landscaping services
(e) getting out
excavated materials by
any means necessary
(f) grubbing up old
roots
(g) levelling or
grading bottoms,
trimming to slopes and
trimming to vertical
and sloping sides
(trimming to surfaces
against which concrete
is directly cast is
measured in
accordance with
02200.10.1.*.*)
(h) compacting
bottoms and sides
(i) protection to
sloping surfaces
(j) additional
excavation to provide
working space and
backfilling thereto
CLASSIFICATION TABLE
1 Excavating 1 Topsoil 1 State average depth m² M3 The quantities D1 Excavating to C2 Trenches for
given are the volume reduce levels includes underground services
before excavating and excavating to form are included in the
no allowance is made cuttings and excavating following sections:
3
2 To reduce levels 1 < 0.30m average depth m for subsequent into banks (a) 02605 - Utility
variations to volume Trenches and
2 >0.30m average depth D2 Trenches include Structures
M4 Trenches attached excavation for (b) 02700 - Sewerage
3
3 Basements and the like 1 Maximum depth < 2.00m m 1 Commencing level to pile caps or pits are thickenings to slab on and Drainage
stated measured between the grade, beds and the like
4 Trenches 2 Maximum depth in further pile caps or pits
stages of 2.00m D3 Pits include
5 Pile caps stanchion, column or
pier bases, isolated
6 Pits footings, lift pits and
the like
3
2 Extra over any type 1 Breaking out existing 1 Rock m D4 Rock is defined as
of excavation materials naturally occuring hard
2 Concrete material which
necessitates its removal
2 Breaking up existing 3 Reinforced concrete and m² by means of explosives,
hard surfaces, concrete hollow blocks pneumatic equipment,
thickness stated if wedges or chemical
known 4 Coated macadam or cracking and where its
3
asphalt volume >1.00m
3
3 Excavating for soft m
spots including
disposal and
backfilling with
approved granular
material
3
3 Disposal 1 Topsoil 1 Deposited on site m 1 Specified locations, M5 The quantities C3 The work is held to
details stated given are the volume include for all multi-
3
2 Excavated materials 2 Off site m before excavating and handling to and from
no allowance is made temporary spoil heaps
for subsequent as and if necessary
variations to volume
C4 Disposal is held to
include any type of
excavated material or
broken out materials-
10 Surface treatments 1 Trimming to surfaces 1 Horizontal m² M10 Trimming to D9 Battered faces are
of excavations to surfaces of excavations faces <15º from vertical
receive concrete 2 Sloping <15° is only measured to
those surfaces where
2 Trimming exposed 3 Sloping >15° concrete is cast directly
surfaces of rock to against the surface of
produce fair face 4 Vertical and battered the excavation
CLASSIFICATION TABLE
3
2 Excavating and 1 Thickness of wall, 1 Support fluid, details m M1 The quantities given C2 The following are S2 Details of support
disposal maximum depth and stated are the volume before held to be included: fluid
commencing level excavating and no (a) support fluid
stated allowance is made for (b) subsequent disposal S3 Limitations on
subsequent variations to of support fluid method of disposal
volume (c) disposal of excavated
material off site
(d) excavating in any
ground encountered
except as otherwise
provided in this section
(e) removal of dead
services
(f) getting out excavated
materials by any means
necessary
(g) grubbing up old roots
3
3 Extra over excavation 1 Breaking out existing 1 Rock m D1 Rock is defined as
materials naturally occuring hard
2 Concrete material which
2 Breaking up existing m² necessitates its removal
hard surfaces, 3 Reinforced concrete by means of explosives,
thickness stated if and concrete hollow pneumatic equipment,
known blocks wedges or chemical
cracking and where its
3
4 Coated macadam or volume >1.00m
asphalt
6 Reinforcement kg M5 Reinforcement is
measured in accordance
with Section 03200 -
Concrete Reinforcement
P1 The following information is provided, where available: M1 Steel sheet piling is C1 Work is held to S1 Kind and quality
(a) soil investigation results measured the net include strutting and of materials
(b) ground water level and the date when it was established elevation area (not shoring to steel sheet
(c) location of underground services developed) along the piling during subsequent
(d) any particular requirement regarding phasing or sequence of piling center line of the piling excavation and
foundation work
C2 Withdrawn piles
become the property of
the Contractor unless
otherwise described
C3 Piles described as
withdrawn are held to
include:
(a) cost of withdrawing
(b) allowance for any
credit for withdrawn
piles which become the
property o fthe
Contractor
CLASSIFICATION TABLE
2 Trial piles
P1 The following information is provided, where available: C1 Withdrawn piles S1 Kind and quality
(a) soil investigation results become the property of of materials
(b) ground water level and the date when it was established the Contractor unless
(c) location of underground services otherwise described
(d) any particular requirement regarding phasing or sequence of piling
C2 Piles described as
withdrawn are held to
include:
(a) cost of withdrawing
(b) allowance for any
credit for withdrawn
piles which become the
property o fthe
Contractor
CLASSIFICATION TABLE
3 Trial piles
02364/1
Copyright : Davis Langdon & Seah Philippines Inc.
02364 Isolated Steel Piles (continued) 02364/2
3 Driving piles 1 Cross sectional 1 Commencing level m 1 Battered M1 Measured from the C4 Driving is held to
shape, dimensions stated point in contact with the include:
and weight per meter 2 Subsequently ground to the point when (a) jointing to extend
withdrawing driven piles
(b) driving through any
3 Trial piles ground encountered
(c) driving through rock,
concrete, reinforced
concrete, roots and all
other obstructions
including excavation and
breaking out as necessary
(c) disposal of spoil off
site
CLASSIFICATION TABLE
2 Boring pile holes 1 Nominal diameter 1 Maximum depth and m 1 Support fluid M1 Measured from the C2 Boring pile holes is
stated commencing level point of entry into the held to include:
stated 2 Battered ground to the bottom of (a) boring through any
the bore ground encountered
3 Trial piles (b) boring through rock,
M2 Support fluid is concrete, reinforced
included in the concrete, roots and all
description where other obstructions
designed by the (c) disposal of excavated
Structural Engineer material off site
(d) supports to sides of
excavations including
support fluid
4 Extra over for 1 Formation of 1 Nominal diameter No 1 Trial piles C4 Enlarging bases is
enlarged bases stated held to include:
(a) additional excavation
and disposal
(b) additional concrete
02370/1
Copyright : Davis Langdon & Seah Philippines Inc.
02370 Bored Cast in Place Piles (continued) 02370/2
6 Cutting off tops of 1 Nominal diameter No 1 Trial piles C5 Cutting off tops of
piles stated piles is held to include:
(a) integration of
reinforcement into pile
caps or ground beams
including cleaning,
cutting and bending
(b) disposal
P1 The following information is provided, where available: M1 Water distribution is C1 All excavation is held S1 Kind and quality
(a) soil investigation results given under one of the to include: of materials
(b) ground water level and the date when it was established following headings: (a) excavating in any
(c) location of underground services (a) Chilled water system ground encountered
except as otherwise
(b) Domestic water provided in this section
system (b) excavating around
(c) Fire water system existing services
(d) Others, stated (c) temporary support to
existing services
M2 Sewerage and
(d) removal of dead
drainage is given under
services
one of the following
(e) getting out excavated
headings:
materials by any means
(a) Subdrainage system necessary
(b) Storm drainage (f) grubbing up old roots
system (g) levelling or grading
bottoms, trimming to
(c) Sanitary sewerage
slopes and trimming to
(d) Combined vertical and sloping sides
wastewater system (h) compacting bottoms
(e) Others, stated and sides
(i) additional excavation
to provide working space
and backfilling thereto
(j) earthwork support
(k) removal of water by
pumping or otherwise
CLASSIFICATION TABLE
1 Excavating trenches 1 Pipes < 200mm 1 Average depth m 1 Commencing level C2 Work is held to S2 Backfilling
diameter 250mm include: material where other
2 Curved (a) backfilling with than selected
2 Pipes > 200mm 2 and thereafter in selected excavated excavated material
diameter, size stated stages of 250mm material or as otherwise
described
3 More than one pipe, (b) disposal of surplus
sizes stated excavated material off
site
6 Pipes 1 Nominal size 1 In trenches m 1 Wrapping M3 Pipes are measured C4 Pipes are held to S3 Method of jointing
over all bends, junctions include for: pipes
2 Other, stated 2 Vertical and similar fittings (a) all jointing materials
(b) brackets for fixing to
3 Curved pipes walls, manhole sides and
the like
4 Straight pipes set out (c) concrete thrust blocks
to curve
7 Extra over pipes for 1 Fittings 1 Dimensioned No 1 Wrapping M4 Reducing fittings are D1 Fittings include C5 Fittings are held to S4 Method of jointing
description measured extra over the bends, junctions, include: to pipes if different to
largest of the pipes on reducers, connectors, (a) extra joints on pipes general pipes
which they occur and adaptors and the like (b) concrete thrust blocks
include for separate
reducers where a fitting
of the required sizes is
not avavailable
10 Manholes 1 Dimensioned 1 Commencing level of No 1 Backdrops D4 The depth given is C7 Work is held to S5 Backfilling
description and depth excavation stated that from the cover include: material where other
11 Inspection chambers to invert level to the invert level (a) excavation than selected
(b) backfilling with excavated material
12 Septic Tanks selected excavated
material or as otherwise
described
(c) disposal of surplus
excavated material
(d) connections of pipes
(e) all work necessary to
complete the manhole,
chamber or septic tank
13 Extra over any type 1 Breaking out existing 1 Rock m3 M5 The volume of D5 Rock is defined as
of excavation materials breaking out existing naturally occuring hard
2 Concrete materials in trenches is material which
based on the width of the necessitates its removal
3 Reinforced concrete beds in the trenches. by means of explosives,
and concrete hollow Where there are no beds pneumatic equipment,
blocks the width to be taken is wedges or chemical
the nominal size of the cracking and where its
pipe plus 300mm volume >1.00m3
2 Breaking up existing 1 Roads m 1 Reinstating to match M6 Lengths are C8 Removal and S6 Type and thickness
hard surfaces, pipe existing measured across reinstatement of curbs of surfacing, base and
diameter stated 2 Sidewalks manholes and other and channels are held to sub-base courses, if
chambers be included known
3 Paths and pavings
C9 Work is held to
include additional
breaking up and
reinstatement to and
around manholes and
other chambers
CLASSIFICATION TABLE
2 Contractor designed 1 Load to be carried 1 Commencing level No 1 Designed length M1 Lengths and depths C2 Contractor designed S1 Types of piles,
piles stated and depth of stated are measured to the cut piles are held to include: method of driving or
top of piles below off levels of the piles (a) driving or boring boring and other
commencing level 2 Battered through any ground Structural Engineer's
M2 Lengths are only encountered requirements
3 Trial piles given where designed by (b) driving or boring
the Structural Engineer through rock, concrete,
reinforced concrete, roots
and all other obstructions
including excavation and
breaking out as necessary
(c) disposal of spoil off
site
(d) all work included in
Sections 02361 to 02370
as applicable
02400/1
Copyright : Davis Langdon & Seah Philippines Inc.
02400 Contractor Designed Piles (continued) 02400/2
9 Macadam
CLASSIFICATION TABLE
1 Fencing 1 Dimensioned 1 Type, spacing, height m 1 Fencing set out to a D2 The height of C2 Work is held to S3 Type and size of
description and depth of supports curve but straight fencing is measured include: footings to supports
between posts from the surface of the (a) ends, angles, bends
ground (or other stated and all other changes in S4 Where not
2 Curved fencing, radii base) to the top of the direction supported by footings,
stated infilling or, where there (b) excavating holes for method of fixing and
is no infilling, to the top supports nature of base
3 Fencing to ground wire or rail (c) backfilling with
sloping > 15º from selected excavated S5 Backfilling
the horizontal D3 Curved fencing is material or as otherwise material where other
fencing curved between described than selected
supports (d) disposal of surplus excavated material
excavated material off
site
D7 The depth of
supports is the depth
below the surface of the
ground or other stated
base
P1 The following information is provided, where available: C1 All excavation is held S1 Kind and quality
(a) soil investigation results to include: of materials
(b) ground water level and the date when it was established (a) excavating in any
(c) location of underground services ground encountered
except as otherwise
provided in this section
(b) excavating around
existing services
(c) temporary support to
existing services
(d) removal of dead
services
(e) getting out excavated
materials by any means
necessary
(f) grubbing up old roots
(g) levelling or grading
bottoms, trimming to
slopes and trimming to
vertical and sloping sides
(h) compacting bottoms
and sides
(i) additional excavation
to provide working space
and backfilling thereto
(j) earthwork support
(k) removal of water by
pumping or otherwise
CLASSIFICATION TABLE
1 Excavating trenches 1 Services < 200mm 1 Average depth m 1 Commencing level D1 If the service is laid C2 Work is held to S2 Backfilling
diameter 250mm in a duct it is the include: material where other
2 Curved diameter of the duct (a) backfilling with than selected
2 Services > 200mm 2 and thereafter in which is given selected excavated excavated material
diameter, size stated stages of 250mm material or as otherwise
described
3 More than one (b) disposal of surplus
service, sizes stated excavated material off
site
2 Beds 1 Width and thickness 1 Nominal diameter of m 1 Curved D2 If the service is laid C3 Work is held to
of bed service stated in a duct it is the include formwork
diameter of the duct
3 Beds and haunchings which is given
6 Ducts 1 Nominal size 1 In trenches m 1 Wrapping M1 Ducts are measured C4 Ducts are held to S3 Method of jointing
over all bends, junctions include for: ducts
2 Other, stated 2 Curved ducts and similar fittings (a) all jointing materials
(b) brackets for fixing to
3 Straight ducts set out walls, chamber sides and
to curve the like
(c) concrete thrust blocks
4 Vertical
7 Extra over ducts for 1 Fittings 1 Dimensioned No 1 Wrapping D3 Fittings include C5 Fittings are held to S4 Method of jointing
description bends, junctions, include: to ducts if different to
reducers, connectors, (a) extra joints on ducts general ducts
adaptors and the like (b) concrete thrust blocks
2 Breaking up existing 1 Roads m 1 Reinstating to match M3 Lengths are C7 Removal and S6 Type and thickness
hard surfaces, service existing measured across reinstatement of curbs of surfacing, base and
diameter stated 2 Sidewalks chambers and channels are held to sub-base courses, if
be included known
3 Walkways and
pavements C8 Work is held to
include additional
breaking up and
reinstatement to and
around chambers
C1 Excavation is held to
include:
(a) excavating in any
ground encountered
(b) getting out excavated
materials by any means
necessary
(c) grubbing up old roots
(d) levelling bottoms and
trimming to vertical and
sloping sides
(e) compacting bottoms
and sides
(f) additional excavation
to provide working space
and backfilling thereto
(g) earthwork support
(h) removal of water by
pumping or otherwise
CLASSIFICATION TABLE
1 Fixtures and fittings M1 Work is measured in C2 Work is held to S1 Type and size of
accordance with the include: footings to supports
2 Balustrades following as applicable: (a) excavating holes for
(a) 05500 - Metal supports S2 Where not
3 Railings Fabrications (b) backfilling with supported by footings,
(b) 06400 - Architectural selected excavated method of fixing and
4 Handrails Woodwork material or as otherwise nature of base
(c) 06600 - Plastic described
Fabrications (c) disposal of surplus S3 Backfilling
excavated material off material where other
site than selected
(d) formwork to footings excavated material
(e) all necessary
supports, fixings and
ancillary work
CLASSIFICATION TABLE
1 Tendons 1 In suspended slabs 1 Number, length and No 1 Curved M1 Lengths are given as C1 Work is held to S2 Details of:
diameter of strand, a straight line between include: (a) ultimate tensile
2 In beams wire or bars which outer faces of anchorages (a) ducts and grouting to strength and jacking
make up the tendons with no allowance for ducts force applied to
undulations along the (b) anchorages including tendons
length of the tendon anchor plates, cones, (b) duct type and size
wedges and the like (c) type of grout
(c) sheathing (d) anchorages
(d) supports to the (e) type of sheathing
material used in the (if any)
formation of ducts
(e) forming and grouting
of air holes
(f) degreasing,
straightening, cutting to
lengths and assembling
tendons and cutting off
ends after tensioning
(g) formwork to form
recesses for anchorages
and filling with grout
CLASSIFICATION TABLE
4 Seeding 1 Rate stated m² 1 Preparatory work, C3 Seeding and turfing are S2 Method of
details stated held to include work to securing turves
contours and slopes <15°
2 Sloping > 15°
C4 Seeding is held to
include raking or
5 Turfing harrowing in and rolling
7 Trees 1 Botanical name 1 Girth and height No C5 Work is held to S3 Size of pits, holes
include: and trenches,
(a) excavating or forming excavated or formed
pits, holes or trenches
(b) backfilling with S4 Details of any
selected excavated supports, ties, guards,
8 Young nursery stock 1 Height No material or as otherwise wrapping and other
trees described sundry work
(c) disposal of surplus
9 Shrubs excavated material S5 Backfilling
(d) removal of surface material where other
and ground water than selected
(e) watering in excavated material
10 Hedge plants 1 Height stated No (f) initial cutting back
(g) labelling S6 For relocation of
trees, shrubs and
C6 Relocation is held to plants details of:
include maintenance of (a) existing and new
2 Height, spacing, m the trees, shrubs or plants locations
number of rows, and until replanted (b) temporary storage
layout stated including details of
nurseries and duration
of storage
11 Herbaceous plants 1 Size stated No
14 Relocate existing No
shrubs
15 Relocate existing
plants
M9 If the width of a
column is > four times its
thickness it is classified
as a wall
12 Soffits of waffle 1 Size of recesses and 1 Height to soffit m² M11 Measured the flat D9 Soffits of waffle and
slabs profile, centers of < 3.50m area of the soffit with no troughed slabs include
recesses and overall allowance for the profile margins whose width is
13 Soffits of troughed slab thickness stated 2 Thereafter in 1.50m of the recesses < 500mm
slabs stages
16 Sides and soffits of 1 Depth <0.75m 1 Height to soffit m² 4 Curved M12 Edges of suspended D10 Depths of beams S3 Curved beams are
beams and girders < 3.50m slabs associated with and girders attached to separated by those
2 Depth >0.75m attached beams and slabs are measured from curved on plan and
2 Thereafter in 1.50m girders at slab perimeters the soffit of the slab those curved on
stages are included with the elevation
beams and girders D11 Beams and girders
include casings to
structural steel beams
and girders
24 Edges of drop
panels
26 Steps in soffits
33 Corbels
34 Balustrades
35 Counters, shelves
and the like
36 Louvers
38 Moulded edges
39 Ornamental features 1 Grooves 1 Size and shape stated m 1 Curved M15 Ornamental features
to fair faced are only measured to
concrete 2 Rebates formwork to produce a
fair faced finish
3 Drips
5 Recesses
CLASSIFICATION TABLE
1 Tendons 1 In suspended slabs 1 Jacking force No M1 Lengths are given as C1 Work is held to
applied, length and a straight line between include:
2 In beams reference outer faces of anchorages (a) ducts and grouting to
with no allowance for ducts
undulations along the (b) anchorages including
length of the tendon anchor plates, cones,
wedges and the like
(c) sheathing
(d) supports to the
material used in the
formation of ducts
(e) forming and grouting
of air holes
(f) degreasing,
straightening, cutting to
lengths and assembling
tendons and cutting off
ends after tensioning
(g) formwork to form
recesses for anchorages
and filling with grout
CLASSIFICATION TABLE
1 Bar 1 General 1 Diameter stated and kg 1 Bent to suit curved D1 Where bars are C2 The contractor is to
reinforcement location concrete shown in lengths >12m allow in his rates for any
they are measured in additional laps/slices
2 Links, stirrups and 2 Helical 12m lengths with required to suit his
binders allowance for laps at construction
3 > 12m in length, joints unless methodology
3 Spacers and chairs given in stages of 3m specifically required by
designed by the the Structural Engineer
Structural Engineer to be in other lengths
D2 Bar reinforcement
includes dowel bars
2 Fabric 1 Dimensioned 1 Minimum laps m² 1 Bent to suit curved M5 Fabric is measured C3 Fabric reinforcement
description or weight concrete work the net area covered with is held to include:
per m² and location no allowance for laps (a) notching around
2 In casings to obstructions
structural steel, M6 No deduction is (b) extra material for laps
columns, beams and made for voids (c) spacers and chairs
girders < 1.00m² whether designed by the
Structural Engineer or
not
C4 Fabric in casings to
structural steel, columns,
beams and girders is held
to include welding to the
structural steel member
1 Designed joints 1 Dimensioned m 1 Curved M2 Locations should C1 Waterstops are held S2 Details of
description and follow the classifications to include welded joints (a) fillers and sealants
location 2 Waterstops in Section 03300 - Cast and special fittings at (b) waterstops
in Place Concrete ends, angles and (b) dowel bars (where
3 Sealants intersections measured as part of
the joint)
4 Formwork C2 Cutting and fitting
around reinforcement and
dowel bars are held to be
included
2 Joints not designed by item M3 This item is included C3 Joints are held to
the Structural in the bills of quantities, include:-
Engineer even if joints are (a) formwork
designed by the (b) fillers and sealants
Structural Engineer, so (c) waterstops
that any additional joints (d) dowel bars
required for the (e) additional
Contractor's method of reinforcement required
working can be allowed due to the joint
for (f) all other necessary
work
1 Blinding beds 1 Thickness stated m³ 1 Sloping < 15º C3 Blinding beds are
held to include:
2 Sloping > 15º (a) formwork
(b) casting against face
3 Vertical of excavations
2 Wall footings and the m³ 1 Casting against faces M6 Wall footings are D1 Ground beams
like of excavations measured between include tie beams and
attached column bases the like
3 Column bases,
isolated footings,
pedestals and the like
4 Pile caps
5 Ground beams
6 Mat foundations
7 Columns
m³ M7 If the width of a
8 Casings to structural column is >four times its
steel columns thickness it is classified
as a wall
9 Walls 1 Thickness stated m³ 1 Casting against faces M8 Walls are measured D2 The stated C4 Laying or finishing to
of excavations between columns thickness is that of the falls, currents or cambers
10 Retaining walls general area and are held to be included
M9 The measurement of excludes thickenings,
11 Parapet walls and suspended slabs are taken projections and
planter walls across attached beams recesses
except where beams are
12 Slab on grade, beds 1 Sloping < 15º of a different mix D3 The stated
and the like thickness of waffle
2 Sloping > 15º M10 Waffle and and troughed slabs is
13 Suspended slabs troughed slabs include the overall thickness
3 Casting against faces margins whose width is
14 Waffle slabs of excavations < 500mm. Wider D4 Suspended slabs
margins are included include:
15 Troughed slabs with suspended slabs (a) ramp slabs
(b) landings at floor
16 Machine bases and M11 Cantilevered planter level
plinths boxes are measured in (c) attached drop
item 03300.23 panels
19 Upstand beams
22 Curbs, upstands, m³
zocalos and the like
23 Sunbreakers, fins,
hoods, fascias,
cantilevered planter
boxes and the like
24 Copings
25 Corbels
26 Balustrades
27 Counters, shelves
and the like
28 Louvers
1 Surface finishes to 1 Power floating m² 1 Sloping > 15º C1 Surface finishes are
unset concrete held to include work to
2 Trowelling 2 Curved falls, currents and slopes
< 15º
3 Wood floating 3 Surface treatment,
details stated
4 Broom finishing
2 Surface finishes to set 1 Rubbed finish 1 Floors m² 1 Surface treatment, D1 Beams attached to C2 Floors are held to S2 Description of
concrete details stated ceilings are classified as include work to falls, finish required and
2 Hacking 2 Landings the same height to soffit currents and slopes method of achieving
as the ceiling where the
3 Grinding 3 Walls and columns finish is the same in
nature
4 Sandblasting 4 Treads, risers and
strings
3 Surface treatment,
details stated
m²
2 Extra over for 1 Special fittings 1 Dimensioned No 1 Curved M3 Special fittings are D1 Special fittings are
description only measured on items ends, angles and
m measured m or m², where intersections which
applicable differ from the general
design
P1 A general description of the prestressed precast units and the system and method of tensioning
P2 Particulars of:
(a) Tendons and any preparatory treatment
(b) Whether tendons are to be pre-tensioned or post tensioned or tensioned as the load is applied.
(c) Maturity of concrete before pre-tensioning is released or post-tensioning is applied
(d) Tests to be applied
CLASSIFICATION TABLE
1 Floors 1 Thickness m² 1 Sloping > 15º D2 Floors include to C2 Floors and roofs are
floors within roof held to include for laying
2 Landings 2 Curved spaces to falls, currents and
slopes < 15º
3 Roofs 3 Patterned, details
stated
9 Strings
10 Splashbacks
11 Fascias
12 Linings to channels
13 Coverings to curbs
14 Cappings
1 Concrete hollow 1 Walls, thickness 1 Built fair and pointed m² 1 Curved, radii stated D1 Walls are held to be C2 Concrete hollow S2 Composition and
block stated one side vertical and of constant block walls are held to mix of mortar
thickness unless include for:
2 Solid concrete block 2 Built fair and pointed otherwise described (a) reinforcement S3 Type of pointing
both sides including dowel bars and where built fair
3 Brick starter bars
(b) filling cavities with S4 For concrete
4 Glass block mortar hollow block walls,
(c) cast in place concrete details of:
stiffeners and lintel (a) reinforcement
beams including (b) concrete stiffeners
formwork and
reinforcement and
precast concrete hollow
beam blocks forming
lintel beams (lintels over
openings are measured
separately.
See 04200.10)
C3 Concrete hollow
block walls and solid
concrete block walls are
held to include:
(a) blocks of special
shape and size at ends,
angles or as otherwise
required
(b) concrete infilling
around inserts and
protrusions or as
otherwise necessary
7 Mesh reinforcement 1 Width 1 Minimum laps m 1 Horizontal M4 Work is measured C5 Work is held to
in joints of block or the net length covered include extra material for
brick walls 2 Vertical with no allowance for laps
laps
3 Curved
8 Damp-proof courses
9 Designed joints 1 Dimensioned m 1 Sealants M5 Joints are only C6 Joints not designed S6 Details of
description measured where designed by the Structural (a) fillers and sealants
2 Curved by the Structural Engineer are held to be (b) ties and fixings
Engineer included
10 Lintels 1 Cast in place 1 Dimensioned m M6 Cast in place lintels D2 Lintels are isolated C7 Cast in place lintels
description are given as composite lintels over openings. are held to include:
items and described Lintel beams in (a) reinforcement
giving the information in concrete hollow block (b) formwork
the following sections as walls are held to be
necessary: included with the walls. C8 Concrete hollow
(a) Section 03100 - See 04200.C2 beam blocks forming
2 Precast concrete 1 Dimensioned m Concrete Formwork lintels are held to
description (b) Section 03200 - include:
Concrete Reinforcement (a) reinforcement
(c) Section 03300 - Cast including dowel bars and
in Place Concrete starter bars
(d) Section 03345 - (b) filling cavities with
Concrete Finishing mortar
3 Concrete hollow 1 Dimensioned m (c) blocks of special
beam blocks description M7 Precast concrete shape and size at ends,
lintels are measured in angles or as otherwise
accordance with Section required
03400 - Precast Concrete (d) temporary support
M1 Wood flooring which D1 All sizes are C1 Work is held to S1 Kind and quality
is designed to be a nominal sizes unless include: of materials
finished surface is described as finished (a) all labors, except as
measured in Section sizes otherwise required S2 For solid timber if
09550 - Wood Flooring (b) breather paper rough or dressed and
lining/sheathing if kiln dried
(c) nailing, screwing and
gluing S3 Method of
(d) drilling and plugging jointing or form of
concrete, masonry and construction
the like with hardwood
or proprietary plugs for S4 Method of fixing
fixing with nails or
screws S5 Nature of base,
(e) punching in nail where other than
heads and covering with timber
approved wood filler
(f) countersinking screw S6 Preservatives
and bolt heads and treatments applied as
covering with approved part of the production
wood filler or wood process
pellets
(g) selecting and keeping S7 Surface treatments
clean for clear finishes applied as part of the
(h) notching and holes (i) production process
fair, chamfered, splayed
and rounded edges S8 Size of boards and
(j) ends, shaped ends, thickness of sheets
miters, angles and
intersections
(k) joints including
additional materials
(l) bands and margins set
out to different
arrangement or pattern
(m) providing panels of
the sizes indicated on the
drawings
(n) priming backs,
applying coal tar or
similar protective
coatings prior to fixing
1 Floors 1 Dimensioned m² 1 Curved, radii stated M2 No deduction is D2 Floors include to C2 Floors and roofs are
description made for voids floors within roof held to include laying to
2 Walls and columns 2 Patterned, details < 1.00m² spaces and to landings falls, currents and slopes
stated
3 Roofs M3 Fascias and eaves D3 Walls and columns
soffits made up of solid include:
4 Fascias wood, other than (a) edges of openings
boarding, are measured and recesses in walls
5 Eaves soffits in Section 06200 - Finish and columns
Carpentry (b) attached pipe
6 Vertical pipe casings, casings, false columns
false columns and and casings to steel
casings to steel columns where they are
columns the same in nature
P1 The following information is shown on drawings which accompany the bills of quantities M1 Work is separated D1 Ordinary bolts are C1 Work is held to S1 Types and grades
(a) the position of the work in relation to other parts of the work and of the proposed buildings into individual structures plain steel bolts used to include: of materials
(b) the types and sizes of structural members and their positions in relation to each other each given under a join steel members (a) all cutting including
(c) details of connections or of the reactions, moments and axial loads at connection points suitable heading to together and include cutting holes and S2 Surface treatments
identify the work high strength bolts perforations off site prior to
(b) notching, drilling and delivery, details stated
D2 Surface treatments countersinking
prior to erection include (c) welds, rivets and S3 Surface treatments
blast cleaning, ordinary bolts with on site prior to
galvanising and associated nuts and erection, details stated
protective painting. washers
Painting after erection
is included in Section
09900 - Painting
CLASSIFICATION TABLE
1 Columns 1 Cross sectional shape 1 Weight per meter kg 1 Curved M2 The mass of
and dimensions members is measured
2 Beams 2 Cambered from their overall lengths
with no deductions for
3 Purlins 3 Tapered splay cuts or mitered
ends or for the mass of
4 Rails 4 Cranked metal removed to form
notches, holes and
5 Bracing 5 Castellated perforations
8 Wires and cables kg M5 Connections, caps C2 Tie rods and the like
and bases are all grouped are held to include:
9 Tie rods and the like together irrespective of (a) threaded ends
the type or of the member (b) nuts, washers and all
10 Connections, caps to which they are other accessories
and bases attached and include (c) drilling or cutting
plates, brackets, cleats, holes in any material
fillets, stiffeners, packing
pieces and gussets
3 Tapered
4 Cranked
11 Fixtures and fittings 1 Dimensioned No 1 Hardware M5 Work contained in C5 Fixtures and fittings
description the fourth column of the are held to include all
2 Glazing beads classification table are ancillary trims, supports,
only included if supplied components and the like
3 Glazing with the component.
Otherwise they are
measured separately
15 Column guards
M1 Work is only D1 All sizes are C1 Work is held to S1 Kind and quality
measured independently nominal sizes unless include: of materials
in this section where not described as finished (a) nailing, screwing and
included as part of work sizes gluing S2 For solid timber if
measured in accordance (b) drilling and plugging rough or dressed and
with other sections concrete, masonry and if kiln dried
the like with hardwood
or proprietary plugs for S3 Method of
fixing with nails or jointing or form of
screws construction
(c) punching in nail
heads and covering with S4 Method of fixing
approved wood filler
(d) countersinking screw S5 Nature of base,
and bolt heads and where other than
covering with approved timber
wood filler or wood
pellets S6 Preservatives
(e) selecting and keeping treatments applied as
clean for clear finishes part of the production
(f) notching and holes process
(g) fair edges
(h) ends, shaped ends, S7 Surface treatments
miters, angles and applied as part of the
intersections production process
(i) joints including
additional materials
(j) priming backs,
applying coal tar or
similar protective
coatings prior to fixing
(k) provision for wood
preservative treatment
(l) sundry items of a like
nature
1 Baseboards 1 Cross sectional size m 1 Curved, radii stated M2 Fascias and eaves
and shape soffits made up of wood
2 Dado rails, 2 Built up members, sheet or wood boarding
mouldings and the size of components are measured in Section
like to walls stated 06160 - Sheet and Board
Linings and Panelling
3 Cornices
6 Beads
7 Nosings
8 Cappings
9 Window sills
10 Window boards
11 Window casings
12 Fascias
13 Eaves soffits
15 Duct covers
16 Treads
17 Risers
CLASSIFICATION TABLE
1 Structural members 1 Floor members 1 Cross sectional size m 1 Curved, radii stated M1 Bridging is measured D2 Floor members and C2 Work is held to
over joists flat roof members include gusset plates and
2 Wall or partition include joists and the like
members beams
2 Battens
3 Bearers
4 Packings
5 Fillets
4 To horizontal pipe
casings and false
beams
5 To steel columns
6 To steel beams
7 To suspended
ceilings
8 To bulkheads in
suspended ceilings
2 Balustrades 1 Horizontal m 1 Curved, radii stated M2 Metal brackets to C3 Ends, angles, bends
isolated handrails are and all other changes in
3 Railings 2 Sloping measured in one of the direction are held to be
following sections as included
4 Isolated handrails applicable:
(a) Section 05500 - Metal C4 Balustrades include
Fabrications associated handrails
(b) Section 05700 - unless noted otherwise in
Ornamental Metal descriptions
8 Louvers 1 Dimensioned No 1 Hardware M3 Louvers of any D3 Fixtures and fittings C5 Work is held to
description material other than wood include cabinets, include all ancillary
9 Sliding/folding are measured in Section counters, wardrobes, trims, supports,
partitions 10200 - Louvers and shelves and the like components and the like
Vents
10 Fixtures and fittings
M4 Hardware may be
measured separately in
Section 08700 -
Hardware
D4 Beams attached to
ceilings are classified as
the same height to soffit
as the ceiling where the
finish is the same in
nature
13 Linings to gutters
14 Linings to channels
15 Coverings to curbs
16 Linings to 1 Dimensioned No
cesspools, sumps description
and the like
17 Collars around
pipes, railings,
standards and the
like
2 Stone chippings
07120/1
Copyright : Davis Langdon & Seah Philippines Inc.
07120 Asphalt and Fluid Waterproofing (continued) 07120/2
CLASSIFICATION TABLE
D4 Beams attached to
ceilings are classified as
the same height to soffit
as the ceiling where the
finish is the same in
nature
13 Linings to gutters
14 Linings to channels
15 Coverings to curbs
17 Collars around
pipes, railings,
standards and the
like
2 Stone chippings
CLASSIFICATION TABLE
CLASSIFICATION TABLE
1 Floors 1 Thickness m² 1 Across members, D1 Floors include C2 Floors and roofs are
centers of members floors within roof held to include laying to
2 Roofs stated spaces falls, currents and slopes
1 Roof coverings 1 Pitch stated 1 Battens m² 1 Counter battens C2 Coverings are held to S5 Spacing of battens
include: and counter battens
2 Wall coverings 2 Underlay (a) work in forming voids
and holes <0.50m²
3 Curved, radii stated (b) cutting, fitting and
making good around
outlets, pipes and the like
(c) additional battens at
ends, angles and the like
9 Flashings
10 Gutters
11 Filler pieces
CLASSIFICATION TABLE
CLASSIFICATION TABLE
S3 Nature of base
CLASSIFICATION TABLE
CLASSIFICATION TABLE
M1 The following are D1 All sizes are C1 Work is held to S1 Kind and quality of
measured in other nominal sizes unless include: materials
sections unless noted described as finished (a) all labors
otherwise: sizes (b) nailing, screwing, S2 For solid timber if
(a) hardware in Section gluing, bolting, fixing rough or dressed and if
08700 - Hardware with brackets, ties and all kiln dried
(b) pointing around other fixings and
frames and the like with fastenings including S3 Method of jointing
sealant in Section 07900 drilling or cutting holes or form of construction
- Sealants in any material
(c) glazing in Section (c) drilling and plugging S4 Method of fixing
08800 - Glazing concrete, masonry and
the like with hardwood S5 Nature of base,
or proprietary plugs for where other than timber
fixing with nails or
screws S6 Preservatives
(d) punching in nail treatments applied as
heads and covering with part of the production
approved wood filler process
(e) countersinking screw
and bolt heads and S7 Surface treatments
covering with approved applied as part of the
wood filler or wood production process
pellets
(f) selecting and keeping
clean for clear finishes
(g) notching and holes
(h) fair, chamfered,
splayed and rounded
edges
(i) ends, shaped ends,
miters, angles and
intersections
(j) joints including
additional materials
(k) bedding in mortar
(l) filling behind frames
with concrete/mortar
including all necessary
formwork
(m) priming backs of
frames, applying coal tar
or similar protective
coatings prior to fixing
(n) provision for wood
preservative treatment
CLASSIFICATION TABLE
3 Door frames
5 Architraves 1 Dimensioned m
description
M1 The following are D1 All sizes are C1 Work is held to S1 Kind and quality
measured in other nominal sizes unless include: of materials
sections unless noted described as finished (a) all labors
otherwise: sizes (b) nailing, screwing, S2 For solid timber if
(a) hardware in Section gluing, bolting, fixing rough or dressed and
08700 - Hardware with brackets, ties and all if kiln dried
(b) pointing around other fixings and
frames and the like with fastenings including S3 Method of
sealant in Section 07900 drilling or cutting holes jointing or form of
- Sealants in any material construction
(c) glazing in Section (c) drilling and plugging
08800 - Glazing concrete, masonry and S4 Method of fixing
the like with hardwood
or proprietary plugs for S5 Nature of base,
fixing with nails or where other than
screws timber
(d) punching in nail
heads and covering with S6 Preservatives
approved wood filler treatments applied as
(e) countersinking screw part of the production
and bolt heads and process
covering with approved
wood filler or wood S7 Surface treatments
pellets applied as part of the
(f) selecting and keeping production process
clean for clear finishes
(g) notching and holes
(h) fair, chamfered,
splayed and rounded
edges
(i) ends, shaped ends,
miters, angles and
intersections
(j) joints including
additional materials
(k) bedding in mortar
(l) filling behind frames
with concrete/mortar
including all necessary
formwork
(m) priming backs of
frames, applying coal tar
or similar protective
coatings prior to fixing
(n) provision for wood
preservative treatment
4 Screeens
CLASSIFICATION TABLE
1 Type of item, unit or 1 Nature of base stated No D1 The nature of base C2 Work is held to
set stated is the material of the include fixing to any
main component to other backgrounds as
which it is fixed necessary, even though
the material of the main
component is the only
one stated
1 Glass 1 Thickness stated 1 Panes < 0.10m² m² 1 Irregular shaped M1 Panes of irregular D1 The following glass
panes shape are classified and is enumerated in items
2 Panes 0.10 - 0.50m² measured according to 08800.2-4 below:
2 Decorative finish, the smallest rectangular (a) bent or curved
3 Panes 0.50 - 1.00m² described area from which the pane (b) glass with bevelled
can be obtained edges
4 Panes thereafter in 3 Ground edges
1.00m² stages M2 Glass with a D2 Decorative patterns
4 Polished edges decorative finish is to glass which are not
measured here where it is regular across the whole
5 Sandblasted edges a regular finish across the pane are measured as
whole of the pane extra over the glass in
item 08800.7.2
2 Bent glass 1 Thickness stated 1 Size of pane and No 1 Curved C2 Bevelled edges are
shape where not held to include miters
3 Curved glass rectangular 2 Bent
8 Hacking out existing 1 Type of surround and m 1 Beads for re-use, M4 Hacking out existing
glass and preparing method of glazing details stated glass and preparing
rebates stated together with rebates is measured the
type of glass perimeter of the pane
CLASSIFICATION TABLE
1 Curtain walling 1 Dimensioned m² 1 Sloping M2 Curtain walling is C2 Work is held to S1 Kind and quality
description described as Contractor include: of materials
2 Contractor designed 2 Curved, radii stated designed where the (a) all necessary
curtain walling design is not completed additional work at ends, S2 Method of jointing
3 Flat panes set to by the Owner and is left angles, intersections, or form of
curve to be completed by the abutments and the like construction
Contractor (b) bolts, screws,
3 Extra over for 1 Spandrel panels 1 Dimensioned m² 1 Sloping brackets, ties and all S3 Method of fixing
description M3 Window boards are other fixings, fastenings
2 Curved, radii stated only measured in this and supports including S4 Nature of base
section where part of the drilling or cutting holes
3 Flat panels set to curtain walling system in any material and S5 Bedding, jointing
curve casting into concrete and pointing
(c) trimming around compounds
2 Closers around door m 1 Curved, radii stated projections
and window (d) holes S6 Surface treatments
openings (e) bedding in mortar and finishes applied
(f) sealants and pointing before delivery
3 Closers at floors (g) finishes where part of
the components as
4 Window boards delivered
1 Walls and columns 1 Thickness m² 1 Curved, radii stated M3 Metal framework to D3 Walls and columns
support finishes is include edges of
2 External measured in Section openings, recesses and
09100 - Suspended projections on walls and
2 Ceilings and beams m² 1 Height to soffit Ceilings and Metal columns
>3.50m above floor Support Systems
D4 Ceilings and beams
3 Soffits of staircases in stages of 1.50m
include edges of
and landings M4 Timber framework to
openings, recesses and
2 Curved, radii stated support finishes is
projections on ceilings
measured in Section
and beams
3 External 06100 - Rough Carpentry
D5 Beams attached to
ceilings are classified as
the same height to soffit
as the ceiling where the
finish is the same in
nature
CLASSIFICATION TABLE
1 Suspended ceilings 1 Dimensioned 1 Depth of suspension m² 1 Height to soffit M1 The following are D1 Work is held to be C1 Work is held to S2 Size and thickness
description <300mm >3.50m above floor measured in other internal unless include: of panels
in stages of 1.50m sections: described as external (a) all jointing materials
2 and thereafter in (a) metal lathing (b) suspension and S3 Thickness of sheet
300mm stages 2 Integral fittings, suspended ceilings D2 Integral fittings framing members linings
details stated (Section 09205 - Metal include special panels, including fixings, trims
Lathing) diffusers, grilles and the and the like S4 Details of framing
3 Curved, radii stated (b) linings to ceilings on like (c) all cutting and fitting and suspension
timber battens or timber over and around system
4 Patterned, details suspended framework obstructions including
stated (timber framework is cutting and fitting up to S5 Method of fixing
measured in Section frames and around pipes,
5 External 06100 - Rough Carpentry brackets and the like S6 Nature of base
and gypsum board lining (d) cutting holes
is measured in Section (e) preparing bases S7 Treatment of joints
09250 - Gypsum Board ) (f) additional supports and surface finish or
2 Bulkheads 1 Dimensioned m 1 Integral fittings, and all other work to materials to be
description details stated M2 No deduction is provide space for received for sheet
3 Light coves made for voids services in the suspended linings
2 Curved, radii stated < 0.50m² ceiling void
(g) additional supports,
3 Patterned, details M3 Integral fittings are trims and accessories as
stated included with the ceiling necessary to fittings,
where part of the partitions, access panels,
4 External suspended ceiling system diffusers, grilles, light
and they also follow a fittings, fixtures, signs
regular layout. Where and the like
4 Extra over for 1 Access panels 1 Dimensioned No 1 External fittings are not part of the (h) sundry items of a like
description suspended ceiling system nature
2 Special panels or do not follow a regular
layout they are measured
3 Diffusers separately in accordance
with 09100.4.*.*.*
4 Grilles
D5 Beams attached to
ceilings are classified as
2 Ceilings and beams m² 1 Height to soffit the same height to soffit
> 3.50m above floor as the ceiling where the
3 Soffits of staircases in stages of 1.50m finish is the same in
and landings nature
2 Curved
3 External
M1 Work is measured D1 Work in this section C1 Work is held to S1 Kind and quality
that in contact with the includes rigid tile and include: of materials
base and no deduction is slab finishes such as (a) fair joints to all types
made for voids <0.50m² ceramic, mosaic, of work including to S2 Size and thickness
quarry, concrete and existing and shape if other
stone tiles and slabs (b) all jointing materials than rectangular
(c) all fixing materials
D2 Work is held to be including bedding S3 Method of fixing
internal unless mortars, adhesives and
described as external mechanical fixings S4 Nature of base
(d) cleaning, sealing and
D3 The thickness stated polishing S5 Treatment of joints
is the nominal thickness (e) fair edges, angles and
intersections
(f) cutting and fitting into
recessed duct and
manhole covers
(g) dishing to outlets and
gullies
(h) all cutting and fitting
over and around
obstructions including
cutting and fitting up to
frames and around pipes,
brackets and the like
(i) cutting holes
(j) preparing bases
including hacking
concrete to form a key
(k) bonding agents where
necessary or required
(l) sundry items of a like
nature
CLASSIFICATION TABLE
1 Floors 1 Dimensioned m² 1 Floors or roofs M2 Contrasting bands D4 Floors include to C4 Floors and roofs are
description sloping >15º and margins are only floors within roof held to include for laying
2 Landings measured separately in spaces to falls, currents and
2 Curved, radii stated meters where < 300mm slopes < 15º
3 Walls and columns wide. Where bands and D5 Walls and columns
3 Flat rigid tiles or margins are > 300mm include edges of
4 Roofs 2 Contrasting bands m slabs set to curve wide they are measured openings, recesses and
and margins < as general areas of projections on walls and
5 Worktops, vanity 300mm wide, width 4 Patterned, details finishes in square meters columns
tops, seats and the stated stated
like M3 Worktops, vanity D6 Ceilings and beams
5 External tops, seats and the like include edges of
6 Watertank sides and which comprise a single openings, recesses and
bases slab of marble, granite or projections on ceilings
the like are enumerated and beams
5 External
Copyright : Davis Langdon & Seah Philippines Inc.
9 Skirtings 1 Dimensioned m 1 Curved, radii stated C5 Linings to channels
description and coverings to curbs
10 Treads 2 Flat rigid tiles or are held to include
slabs set to curve additional finishes to
11 Risers ends
3 Patterned, details
12 Strings stated
13 Splashbacks 4 External
14 Fascias
15 Linings to channels
16 Coverings to curbs
17 Cappings
18 Cornices
19 Extra over for 1 Special patterns 1 Dimensioned m 1 Curved, radii stated M4 Large feature D8 Special units
description patterns may include units with
2 Special units No 2 Flat rigid tiles or alternatively be measured rounded or other shaped
slabs set to curve net and not extra over edge(s)
3 Patterned, details
stated
4 External
3 External
M1 Wood flooring which D1 All sizes are C1 Work is held to S1 Kind and quality
is designed to be a nominal sizes unless include: of materials
finished surface is described as finished (a) all labors
measured in this Section. sizes (b) selecting and keeping S2 If kiln dried
Wood flooring designed clean for clear finishes
to be covered is (c) notching and holes S3 Size and thickness
measured in Section (d) fair, chamfered,
06160 - Sheet and Board splayed and rounded S4 Method of
Linings and Panelling edges jointing or form of
(e) ends, shaped ends, construction
M2 No deduction is miters, angles and
made for voids intersections S5 Method of fixing
< 1.00m² (f) joints including
additional materials S6 Nature of base
(g) bands and margins set
out to different S7 Preservatives
arrangement or pattern treatments applied as
(h) working over and part of the production
around obstructions process
(i) providing panels of
the sizes indicated on the S8 Surface treatments
drawings applied as part of the
(j) cork or other production process
compression strips at the
perimeter of work S9 Pattern for block
(k) provision for wood and parquet flooring
preservatives treatment
(l) sundry items of a like
nature
CLASSIFICATION TABLE
C2 Work is held to be
dressed timber
4 Risers
CLASSIFICATION TABLE
1 Floors 1 Dimensioned m² 1 Floors sloping >15º M2 Contrasting D4 Floors include to C2 Floors are held to
description bands and margins floors within roof include for laying to
2 Landings 2 Curved are only measured spaces falls, currents and slopes
separately in meters < 15º
3 Walls and columns 3 Patterned, details stated where < 300mm D5 Walls and columns
wide. Where bands include edges of
4 Worktops, vanity 4 External and margins are > openings, recesses and
tops, seats and the 2 Contrasting bands m 300mm wide they are projections on walls
like and margins < measured as general and columns
300mm wide, width areas of finishes in
stated square meters
8 Strings
9 Linings to channels
10 Coverings to curbs
11 Extra over for 1 Special patterns 1 Dimensioned m 1 Curved M3 Large feature D6 Special units
description patterns may include special units to
2 Special units no 2 Patterned, details stated alternatively be provide rounded
measured net and not edges, angles and
3 External extra over intersections
S2 Method of fixing
4 To staircases and
landings
5 To soffits of
staircases and
landings
6 To worktops, vanity
tops, seats and the
like
CLASSIFICATION TABLE
M1 The area or girth D1 Work is held to be C1 Work is held to S1 Kind and quality
measured is the area or internal unless include: of materials
girth covered including described as external (a) preparation of
allowances for the extra surfaces S2 Nature of base
girth of edges, D2 Where reference is (b) rubbing down
mouldings, panels, made to painting it is between coats S3 Preparatory work
sinkings, corrugations, held to include clear (c) cutting to line
carvings and the like, finishing and polishing (d) painting to S4 Priming or sealing
except where otherwise corrugated, fluted, coats (No)
stated D3 Preparation includes panelled, carved,
all preparation ornamental or other S5 Undercoats (No)
M2 No deduction is necessary to the surface irregular surfaces
made for voids to receive the paint (e) removing hardware S6 Finishing coats
<0.50m² system described and the like and (No) and surface
including putty, fillers, replacing after painting finish
sealers and the like (f) painting hinges,
fastenings, fixings and S7 Method of
the like application
S8 If moulded,
panelled, corrugated
or carved surfaces are
measured flat this is
stated in the
description
CLASSIFICATION TABLE
9 Baseboards, dado
rails, cornices, coves
and the like
12 Cabinets, wardrobes
and the like
13 Ceilings and beams 1 Girth > 300mm m² 1 Height to soffit D5 Beams attached to
>3.50m above floor ceilings are classified as
14 Soffits of staircases 2 Girth < 300mm m in stages of 1.50m the same height to soffit
and landings as the ceiling where the
2 External finish is the same in
nature
3 On site before fixing
2 Number of coats
16 Balustrades, 1 Plain open type 1 Girth > 300mm m² 1 External M7 Work described as
railings, fences and plain open type is
gates 2 On site before fixing classified according to
2 Girth < 300mm m the size of the individual
members
M8 Work described as
2 Close type m² close type, mesh covered
or ornamental are
3 Mesh covered or measured flat both sides
ornamental
17 Pipes, conduit and 1 Girth > 300mm m² 1 External D6 Pipes, conduit and C4 Pipes, conduit and the
the like the like include cables, like are held to include
2 On site before fixing ducting and trunking work to:
18 Gutters (a) supports
(b) conduit boxes and
other fittings
(c) pipe fittings and
2 Girth < 300mm m accessories
21 Signwriting 1 Dimensioned No
description
5 Corners No 1 External
6 Motifs
1 Floors 1 Dimensioned 1 Height of cavity m² 1 Integral fittings, M2 Integral fittings are D2 Integral fittings C2 Work is held to
description stated details stated included with the floor include special panels include for laying to
where part of the raised and the like falls, currents and slopes
2 Sloping > 15º floor system and they < 15º
also follow a regular
3 Patterned, details layout. Where fittings
stated are not part of the raised
floor system or do not
4 External follow a regular layout
they are measured
separately in accordance
2 Downstands 1 Dimensioned m 1 Integral fittings, with 10270.6.*.*.*
description details stated
3 Steps in surfaces
2 Curved, radii stated
3 Patterned, details
stated
4 External
3 External
CLASSIFICATION TABLE
CLASSIFICATION TABLE
4 Three way
intersections
5 Four way
intersections
6 Abutments with
walls and columns
CLASSIFICATION TABLE
S5 Method of fixing
CLASSIFICATION TABLE
8 Cutting holes,
mortices, chases and
the like, grouting
and making good
after installation
9 Providing all
sleeves for fixing
through slabs, walls,
beams and the like
11 Sealing, packing
and fireproofing
where work pass
through slabs, walls,
beams and the like
15 Operating and
maintenance
manuals
17 Instruction of
Owner's
representatives in
operation,
maintenance,
preventive
maintenance and
service of
completed
installation
CLASSIFICATION TABLE
C4 Embedded conduit is
held to include:
(a) casting into concrete,
plaster and toppings
(b) cutting chases in any
materials and making
good
C5 Conduit encased in
concrete is held to
include:
(a) concrete
(b) reinforcement
(c) excavation and
breaking out as
necessary
(d) backfilling with
selected excavated
material or as
otherwise specified
2 Boxes 1 Type and size No 1 External M4 Boxes are only D3 Boxes include pull
measured separately boxes, junction boxes,
where designed by the adaptable boxes, floor
Electrical Engineer. trap boxes, purpose
Where not designed but made boxes,
necessary for the flameproof boxes and
installation they are held all other special boxes
to be included with the
conduit by Rule C3(f)
3 Wireways 1 Type and size 1 Surface fixed m 1 External M5 Wireways, cable D4 Surface fixed C6 Wireways, cable
ladders, underfloor ducts wireways, cable ladders, underfloor ducts
and busducts are ladders and cable and busducts are held to
4 Cable ladders 2 Number of measured over all fittings trays include: include:
compartments (a) joints in the running
(a) fixed to surfaces
which are length
subsequently covered (b) joints to conduit and
5 Underfloor ducts 1 Mounted on concrete m 1 Spring floor by suspended ceilings, distribution boards
floors supports, details raised floors, access (c) joints to fittings
stated panels and the like (d) all labors
2 Embedded in (e) components for
concrete and 2 External (b) fixed in ducts or grounding
concrete toppings pipe chases
(c) generally surface
fixed but embedded
6 Busducts 1 Type, rated capacity m 1 External for short parts of their
and number of lengths as required by
busbars the installation
3 Feeder units
4 Plug in circuit
breakers, ampacity
rating stated
5 Expansion joints
6 Special fittings
7 Connections to
equipment
12 Cables 1 Type and size 1 Drawn into conduits, m 1 External M6 Cable is measured D7 Surface fixed C9 Cables are held to
ducts or wireways the net length following cables include: include:
the shortest distance (a) cables fixed to (a) all labors
2 Drawn into existing between points in straight surfaces which are (b) all joints where not
conduits, ducts or lines except that the subsequently covered designed by the
trunking following allowances are by suspended ceilings, Electrical Engineer but
added for tails: raised floors, access required for the
3 Fixed to cable trays (a) 0.30m on each cable panels and the like installation
or ladders entering lighting fixtures (b) cables generally (c) color coding or other
and accessories surface fixed but identification markings
4 Surface fixed (b) 0.60m on each cable drawn into conduits,
entering equipment and ducts or wireways, C10 Cables drawn into
5 Embedded control gear (i.e. motors, fixed to cable trays or existing conduit, ducts or
transformers, embedded for short wireways are held to
6 Wrapping around panelboards, disconnect parts of their lengths include removing and
pipework or switches, enclosed circuit as required by the replacing existing covers,
equipment breakers and the like). installation inspection lids and the
like
7 Laid in trenches
C11 Embedded cables
are held to include:
(a) casting into concrete,
plaster and toppings
(b) cutting chases in any
materials and making
good
2 Line taps
3 Termination kit
18 Final circuits 1 Cables 1 Lighting points, No 1 Surface fixed M7 Final circuits are D8 Surface fixed C13 Final circuits are
stating whether wall measured on an include: held to include:
2 Conduits or ceiling mounted 2 Embedded enumerated points basis (a) work fixed to (a) providing distribution
and whether centrally where they form part of a surfaces which are diagrams and location
3 Cables and conduits or locally controlled 3 External domestic or similar subsequently covered drawings showing the
simple installation from by suspended ceilings, layout of the points
2 Switch points, stating distribution boards and raised floors, access (b) all conduit fittings
whether one or two the like panels and the like and accessories necessary
way and the number (b) work generally for the installation
of gangs M8 Each lighting point is surface fixed but (c) all cable fittings and
measured as one point embedded for short accessories necessary for
3 Intermediate switch irrespective of the parts of their lengths the installation
points number of lamps as required by the (d) all work to conduits
installation included in Rule C3
4 Socket outlet points M9 Socket outlet points, (e) all work to cables
switch points and the like included in Rule C9.
5 Immersion heater are measured as one
points point irrespective of the C14 Embedded final
number of gangs circuits are held to
6 Cooker points include:
(a) casting into concrete,
7 Fan points plaster and toppings
(b) cutting chases in any
8 Air conditioner materials and making
points good
9 Others, stated
19 Equipment 1 Type and size No 1 External D9 Equipment C15 Work is held to S5 Details of links,
includes motors, include fuses, circuit breakers,
20 Panelboards batteries, transformers (a) all necessary supports gland plates, terminal
and the like (b) connections to boxes and the like
21 Disconnect switches conduit, wireways, cable
trays and cables
22 Enclosed circuit
breakers
23 Lighting fixtures 1 Type and size No 1 External D10 Accessories and C16 Work is held to S6 Lighting fixtures are
field devices include include: to include details of
24 Accessories switches, socket (a) boxes, connector reflectors, shades,
outlets, thermostats, blocks lamps and the like
25 Field devices bell pushes, signal (b) connections to
indicating units, conduit, wireways, cable S7 Accessories are to
clocks, telephones, trays and cable state number of gangs
alarm bells, (c) all necessary ancillary where appropriate
loudspeakers, door work including bushes,
status, smoke nipples, locknuts and the
detectors, heat like
detectors and the like (d) grounding
(e) all supports as
necessary for fixing
28 Cutting holes,
mortices, chases and
the like, grouting
and making good
after installation
29 Providing all
sleeves for fixing
through slabs, walls,
beams and the like
30 Wrapping conduits,
cables or trunking in
felt or similar
protection where
work passes through
slabs, walls, beams
and the like
31 Sealing, packing
and fireproofing
where work passes
through slabs, walls,
beams and the like
35 Operating and
maintenance
manuals
37 Instruction of
Owner's
representatives in
operation,
maintenance,
preventive
maintenance and
service of completed
installation
CLASSIFICATION TABLE
1 Gutters 1 Nominal size or girth m M4 Gutters and pipes C3 Gutters and pipes are
are measured over all held to include:
fittings (a) joints in the running
length
M5 Trenches, chambers (b) joints to fittings,
and beds for ancillaries, fixtures and
underground pipes are equipment
measured in Section (c) all labors including
02605 - Utility Trenches made bends
and Structures (d) supports of any
length or type
(e) sundry items of a like
nature
C5 Pipes <60mm
nominal size are held to
include all fittings
2 To floors
3 To ceilings and
soffits
5 In trenches
D5 Equipment includes
boilers, cisterns,
cylinders, tanks, pumps
and the like
11 Cutting holes,
mortices, chases and
the like, grouting
and making good
after installation
13 Wrapping pipes,
conduit, cables or
trunking in felt or
similar protection
where they pass
through slabs, walls,
beams and the like
19 Operating and
maintenance
manuals
21 Instruction of
Owner’s
representatives in
operation,
maintenance,
preventive
maintenance and
service of completed
installation
5 Shower valves