Revision 04/13/10
TM
2005-
Ford Focus
IMPORTANT
Before starting, compare items on your invoice with items received.
Carefully check through packaging material. If any item is missing,
*0000190099*
please call: Crutchfield Technical Support at 1-800-955-9094.
Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented without
warranties or guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicle
production. Any person or entity using this information does so at his or its own risk. If you find our instructions are different from your
Inside... vehicle, or if you have questions, do not continue with your installation. Contact our toll-free technical support for assistance.
Page
3 Receiver Installation*
Phillips Small Flat Blade 1/4” 6mm 7mm 8mm 10mm Panel Tool Shop Rag T15 T20 Drill & 1/8" Bit
(if manual windows) (if necessary)
Screwdriver Screwdriver
Socket Ratchet Torx Driver
& Extension
Tools Required
5. Remove four (4) 7mm screws securing factory radio to dash. Pull out
radio, disconnect and remove (Figure 3).
! SAFETY CHECK
Return gear shift to park position.
FIGURE 3
FIGURE 2
Factory Radio
1-800-955-9094
TECHNICAL SUPPORT Copyright 2010 Crutchfield Corporation 2
019 0099 NOTES: Please read first
• Inspect factory receiver harness connector in vehicle.
6. Standard DIN receivers: Install DIN trim ring supplied with the
installation kit.
Receiver Assembly
1-800-955-9094
TECHNICAL SUPPORT Copyright 2010 Crutchfield Corporation 3
019 0099 NOTES: Please read first
• Instructions show factory size speakers or speakers
Front Door Speakers with adaptor brackets only. Cutting or fabricating (not
shown) will be required for other speaker sizes.
FIGURE 3 FIGURE 4
“C” Clip
5. Remove seven (7) phillips (or Torx T-15) screws around edges of
door panel (Figure 5). Note: There are two (2) additional
screws on 2006- vehicles.
! SAFETY CHECK
Check that wires do not interfere with window operation.
Test door lock and release operation.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2010 Crutchfield Corporation 5
019 0099 NOTES: Please read first
• Instructions show factory size speakers or speakers
Rear Door Speakers with adaptor brackets only. Cutting or fabricating (not
shown) will be required for other speaker sizes.
2. Pry off screw cover behind door release trim FIGURE 1 FIGURE 2
and remove one (1) exposed Torx T20 screw
(Figure 2).
Door Release Trim
3. Pry off front portion of door pull handle.
Remove two (2) recessed 1/4” screws
(Figure 3).
FIGURE 3 FIGURE 4
“C” Clip
1-800-955-9094
TECHNICAL SUPPORT
7. Remove four (4) 6mm screws securing speaker. Pull out speaker,
disconnect and remove (Figure 7).
! SAFETY CHECK
Check that wires do not interfere with window operation.
Test door lock and release operation.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2010 Crutchfield Corporation 7
019 0099
9. Test speaker operation and reinstall rear side Rear Side Panel
panel by reversing removal steps.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2010 Crutchfield Corporation 8
019 0099 NOTES: Please read first
• Instructions show factory size speakers or speakers
Rear Subwoofer -- Hatchback with adaptor brackets only. Cutting or fabricating (not
shown) will be required for other speaker sizes.
Subwoofer Enclosure
1-800-955-9094
TECHNICAL SUPPORT Copyright 2010 Crutchfield Corporation 9
019 0099
FIGURE 6
7. Cut the wires from the harness close to the factory speaker. Strip the
cut wire ends and connect to the new speaker. Note: The correct
method for connecting wires to the speaker will depend upon the type
of terminals on the speaker.
!
Always be careful when drilling in a vehicle. Be aware of
things such as wiring, windows, fuel lines and safety
devices. Check drilling depth and location to avoid
damage to vehicle appearance.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2010 Crutchfield Corporation 10