Section 2.18
Section Dimensions - Lower Inboard Section of Upper Tensioner Pivot Frame
Width of section b 565
Depth of section d 465
Thickness of side top and bottom plates tb 15
Thickness of side plates td 15
Inside width ib 535
Inside depth id 435
Section Properties
Cross sectional area A 30000
Distance to extreme fibre from neutral axis (vertical) y1 282.5
Second moment of inertia (about horizontal axis) I1 1064193750
Radius of gyration of member r 188.3
Member Details
Length of member L 1230
Youngs modulus E 207000
2.18.4 For members subjected to combined bending and compression, the following stress criteria are to be used:
0.675
Section Dimensions - Upper & Lower Inboard Section of Lower Tensioner Pivot Frame
Width of section b 485
Depth of section d 290
Thickness of side top and bottom plates tb 15
Thickness of side plates td 15
Inside width ib 455
Inside depth id 260
Section Properties
Cross sectional area A 22350
Distance to extreme fibre from neutral axis (vertical) y1 242.5
Second moment of inertia (about horizontal axis) I1 319298750
Radius of gyration of member r 119.5
Member Details
Length of member L 2260
Youngs modulus E 207000
Buckling check for beam in bending & compression (Section 2.19, LAME 2009)
Member properties
Area A 10.7
2 Moment of area
nd Ixx 53.3
2 Moment of area
nd Iyy 53.3
Yxx 3
Yyy 3
Radius of gyration r 22.3
Length of member L 3300
mm2
mm
mm4
mm
mm
MPa
Welded box
MPa
MPa Note 3
Fixed - Free
mm
MPa
MPa
LC1
MPa
5.3091835956
OK
mm
mm
mm Averaged
mm Averaged
mm
mm
mm2
mm
mm4
mm
mm
MPa
Welded box
MPa
MPa Note 3
Fixed - Guided
mm
MPa
MPa
LC1
MPa 453.8747
cm²
cm4
cm4
cm
cm
mm
mm
Table 3.2.8
kN
kNm
kNm
N/mm²
N/mm²
N/mm²
N/mmTable 3.2.10
Fail UR = 1866%
Lloyd's Register 2017 Code For Lifting Appliances In A Marine Environment (July)
2.21 Allowable Stress - Plate Buckling Failure LAME 2016 Ch4 Section 2
2.21.1 The allowable stress is to be taken as the critical buckling stress σ cb, σbb, or τb, as appropriate, of the co
concerned multiplied by the stress factor, F, as defined in Table 4.2.6 Stress factor, F .
2.21.2 For components subject to compression stress, the critical buckling stress is given by:
2.21.3 For components subject to shear stress the critical buckling stress is given by:
2.21.4 For components subject to bending stress, the critical buckling stress is given by:
2.21.5 For components subject to combined compression and shear stress, the following allowable stress crite
2.21.6 For components subject to combined bending and shear stress, the following stress criteria are to be m
2.21.7 For components subject to combined bending and compression stress, the following allowable stress c
2.21.8 For components subject to combined compression, bending and shear stress, the following allowable s
m User Input
m User Input
m User Input
MPa User Input
User Input
MPa User Input
MPa User Input
OK
User Input
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
Lloyd's Register 2017 Code For Lifting Appliances In A Marine Environment (July)
Section 2.18
Section Dimensions - Lower Inboard Section of Upper Tensioner Pivot Frame
Width of section b 565
Depth of section d 465
Thickness of side top and bottom plates tb 15
Thickness of side plates td 15
Inside width ib 535
Inside depth id 435
Section Properties
Cross sectional area A 21600
Distance to extreme fibre from neutral axis (vertical) y1 214.8
Second moment of inertia (about horizontal axis) I1 1100000000
Radius of gyration of member r 225.7
Member Details
Length of member L 1230
Youngs modulus E 207000
2.18.4 For members subjected to combined bending and compression, the following stress criteria are to be used:
0.525
Section Dimensions - Upper & Lower Inboard Section of Lower Tensioner Pivot Frame
Width of section b 485
Depth of section d 290
Thickness of side top and bottom plates tb 15
Thickness of side plates td 15
Inside width ib 455
Inside depth id 260
Section Properties
Cross sectional area A 22350
Distance to extreme fibre from neutral axis (vertical) y1 242.5
Second moment of inertia (about horizontal axis) I1 319298750
Radius of gyration of member r 119.5
Member Details
Length of member L 2260
Youngs modulus E 207000
Buckling check for beam in bending & compression (Section 2.19, LAME 2009)
Member properties
Area A 10.7
2 Moment of area
nd Ixx 53.3
2 Moment of area
nd Iyy 53.3
Yxx 3
Yyy 3
Radius of gyration r 22.3
Length of member L 3300
mm2
mm
mm4 0.0011
mm
mm
MPa
Welded box
MPa
MPa Note 3
Fixed - Free
mm
MPa
MPa
LC1
MPa
3.9054545455
OK
mm
mm
mm Averaged
mm Averaged
mm
mm
mm2
mm
mm4
mm
mm
MPa
Welded box
MPa
MPa Note 3
Fixed - Guided
mm
MPa
MPa
LC1
MPa 453.8747
cm²
cm4
cm4
cm
cm
mm
mm
Table 3.2.8
kN
kNm
kNm
N/mm²
N/mm²
N/mm²
N/mmTable 3.2.10
Fail UR = 1866%