Issue 02
General Disclaimer
The information in this document may contain
predictive statements including, without limitation,
statements regarding the future financial and
operating results, future product portfolio, new
technology, etc. There are a number of factors that
could cause actual results and developments to
differ materially from those expressed or implied
in the predictive statements. Therefore, such
information is provided for reference purpose only
and constitutes neither an offer nor an acceptance.
Huawei may change the information at any time
without notice.
www.huawei.com/antenna
Antenna Modernization Paves the Way for MBB 2020
MBB 2020 is geared to future development and will provide users with an unprecedented service experience. The way of exchanging
information will be further upgraded, enabling them to experience more innovative services, such as virtual reality, ultra-HD video,
unmanned driving, remote health care and smart agriculture. Wireless networks as the infrastructure for MBB 2020 will support more
connections between people, between people and things, and between things.
As MBB networks develop, antenna systems will play a key 2. M ulti-beam antennas better support multi-sector
role in unleashing MBB network potential. The addition of networking. A multi-sector networking solution facilitates
new frequency bands, the development of MIMO, and the fast capacity expansion in dense urban areas if spectrum
wide application of multi-sector networking will require the resources are limited. However, traditional narrow-beam
support of antenna systems. antennas cause severe interference between multi-sector
neighboring cells, affecting the capacity expansion effect.
To ensure the smooth evolution of the MBB network to a target Multi-beam antennas can effectively solve the problem of
network over the next three to five years, continuous capacity neighboring cell interference, improving network capacity.
expansion and fast deployment is becoming a must. Antenna 3. Active Antenna Unit (AAU) is the future site evolution
2020 reconstruction geared to MBB 2020 is particularly trend. In traditional site deployment, there are a large number
important. of boxes, making antenna deployment more complicated.
1. A single antenna can support more frequency bands Compared with traditional antennas, AAU has the following
and higher-order MIMO. With the deployment of more advantages:
frequency bands and application of higher-order MIMO, • Simplifies site: AAU reduces the number of devices installed on
antenna systems are becoming more and more complex, and a tower by integrating the radio and antenna systems.
more space is required for antenna installation. Traditional • Promotes deployment efficiency: Integrated installation of
single-band antennas can hardly meet the requirements of radio and antenna systems reduces deployment difficulties and
MBB. time required, promoting deployment efficiency and reducing
Compared with traditional single-band antennas, multi-band deployment costs.
antennas require less installation space, saving site resources. • Improves network performance: AAU can reduce feeder
As antenna systems become increasingly complex, making reliability by 200%. The Self-Aware Antenna (SAA) solution
antennas accessible and adjustable and eliminating site visits enables operators to remotely query antenna mechanical
are the key to decreasing OPEX and improving network O&M downtilt, azimuth, height, and latitude and longitude in real
efficiency. time, facilitating network O&M and improving Self-Organizing
Network (SON) performance. The EasyBeam solution enables
Huawei's innovative plug-and-play EasyRET solution increases operators to remotely adjust the downtilt, azimuth and
the RET system deployment efficiency by 40% and improves horizontal beamwidth, improving network performance.
Constant R&D Investment Driving Innovation
Due to antennas' key role in wireless networks, Huawei will and RAN to ensure optimal antenna performance within the
continue to invest in antenna-related R&D. Huawei currently network. Huawei participates in more than 50 standards
has eight R&D centers committed to active and passive antenna organizations to promote the development of the antenna
technology research around the world. They are in Munich/ industry. In 2014, the EasyBeam solution launched by Huawei
Germany, New Jersey/USA, Ottawa/Canada, Stockholm/Sweden, won GTB's Wireless Network Infrastructure Innovation Award.
Moscow/Russia Shenzhen/China, Xi'an/China, and Shanghai/ In 2015, the SAA solution launched by Huawei received this
China. Huawei uses coordination between the antennas award again.
Stockholm, Sweden
Shenzhen, China
AAS
Passive antenna
New Jersey, USA Ottawa, Canada Munich, Germany Stockholm, Sweden Moscow, Russia Xi'an, China Shanghai, China Shenzhen, China
Strict Quality Control
Huawei's antenna product line places quality above all else. automation equipment to ensure a high degree of consistency and
Huawei has built execution standards and inspection specifications quality. In 2015, Huawei realized comprehensive lead-free antenna
for each process, including supplier management, incoming production. Eco-friendly antennas help improve the environment
material inspection, production, delivery, and customer satisfaction and contribute to sustainable social and economic development
management. The production process uses a large amount of and also set a new benchmark in the antenna industry.
Automated cable Automated Automated phase Automated screw Automated soldering Automated Antenna
stripping connector soldering shifter soldering driver of feeding network packing production line
Netherlands
Hungary
Europe / Russia / Turkey / North Africa
Mexico
North America/Latin America Dubai Shenzhen
Middle East/Southeast Africa China/Middle Asia/South Pacific/Southeast Asia/
Panama East Russia/West Africa/North Africa
Nigeria
Brazil
Example: D XXXXX-690-960/1710-2690/1710-2690/1710-2690/1710-2690-65/65/65/65/65-17i/18i/18i/17.5i/17.5i-M/M/M/M/M-B/R
Diagram: X1 X2 X3 X4 X5 X6 X7
D Directional
O Omni-directional
C Cluster
X1 I Indoor
CP Camouflage Pipe
X X Polarization
V Vertical Polarization
X2
H Horizontal Polarization
C Circular Polarization
X5 Number Gain(dBi)
C Combiner Integrated
T TMA Integrated
R RCU Integrated
X7 AS Azimuth Steering
HE High Efficiency
S 4.3-10 Connector
Colour coding is used to identify antenna RF ports and also for RET remote identification. Colour coding consists of five
parts generally: colour code, pattern coding, array numbering, array symbol and RCU serial number.
A hexa-band EasyRET antenna is used as an example to illustrate colour coding:
3. Array Numbering
(Used to mark different array ID and
array positions. For details, please see
chapter 3.)
4. Array Symbol
(Used to display the physical structure of the antennas. For details, please see chapter 4.)
Two types of array symbol are used (Type 1 and Type 2). Which type is used depends on specific antennas. This also applies
to chapter 3 Array numbering and chapter 5 RCU serial number.
Type 1 Type 2
2 Filtered Low Bands 2 Filtered Low Bands
r1: 690-862MHz r: 690-862MHz
r2: 880-960MHz rr: 880-960MHz
r1 and r2 share the same low-band array r and rr share the same low-band array
Ly1 Cy2 Rb1 Ry3 4 high-band arrays yL yyC bR yyyR 4 high-band arrays
Ly1, Cy2: 1710-2690MHz yL, yyC: 1710-2690MHz
Rb1: 1710-2200MHz bR: 1710-2200MHz
Ry3: 2490-2690MHz yyyR: 2490-2690MHz
r1 r2 r rr
Rb1 and Ry3 share the same low-band array bR and yyyR share the same low-band array
Type 1: Type 2:
HWMxxx..........r1 HWMxxx..........Ly1 HWMxxx..........r HWMxxx..........yL
HWMxxx..........r2 HWMxxx..........Cy2 HWMxxx..........rr HWMxxx..........yyC
HWMxxx..........Rb1 HWMxxx..........Ry3 HWMxxx..........bR HWMxxx..........yyyR
AISG Colour Coding Technology
1. Colour Code
According to AISG, the upper band edge ranges of the antenna port are represented by red, green, blue, and yellow in
sequence from the low band range to the high band range. The following table shows the definition of the frequency
range and the associated colour code abbreviation.
Upper Band Edge Range Assigned Colour Code Colour Code Abbreviation
700MHz to 1000MHz RAL 3020 r
1001MHz to 1700MHz RAL 6029 g
1701MHz to 2300MHz RAL 5015 b
2301MHz to 4000MHz RAL 1023 y
2. Pattern Coding
Pattern coding is used for differentiation of array ports carrying the same colour code.
Different segments of colour and gaps are shown in the following table.
Note: Gaps between coloured segments may be white gaps or black lines.
y1 y2 y3 y4 y5
(or y) (or yy) (or yyy) (or yyyy) (or yyyyy)
3. Array Numbering
For multi-band antennas, different arrays are indicated by their colour code abbreviations, array IDs, as well as array positions.
There are two types of array numbering.
Array ID: e.g. “y1” or “y” for the first high-band array, ”y2” or ”yy” for the second high-band array.
Array position is represented by abbreviation (e.g. L, C, R, T, M, and B), the following table shows the details.
Take a hexa-band antenna for example, array with Ry3 or yyyR means the third high-band array and located at right
position inside of antenna.
AISG Colour Coding Technology
4. Array Symbol
In order to better display the physical structure of Huawei antennas, the array symbol corresponding to the array ID
and array position is shown in the catalogue.
The following figures show the physical structures of different antennas as examples:
Ⅰ. Dual-band Antenna
Ⅱ. Dual-band Antenna
2 Filtered Low Bands ("Dipole reuse")
2 Side-by-side Low-band Arrays
e.g. 790-862/880-960 or r1 r2 r rr Lr1 Rr2 rL rrR
e.g. 690-960/690-960 MHz
690-803/824-960 MHz
Ⅵ. Tri-band Antenna
Ⅴ. Tri-band Antenna
Tb1 bT 1 Low Band
1 Low Band
2 Side-by-side High-band Arrays
2 Stacked High-band Arrays
e.g. 790-960/1710-2690/1710- Ly1 Ry2 yL yyR
e.g. 790-960/1710-
2690 or 690-960/1710-
2180/1710-2180 MHz
Bb2 bbB 2690/1710-2690 MHz
r1 r r1 r
The SN (serial number) of integrated RCU contains colour coding information, EasyRET antennas support remote RCU
identification by colour coding.
The SN of an integrated RCU contains 19 digits. The following describes a hexa-band EasyRET antenna's SN as an example:
Type 1: H W M 1 5 3 4 F 6 0 0 1 0 0 2 1 R y 2
Type 2: H W M 1 5 3 4 F 6 0 0 1 0 0 2 1 y y R
Color coding:
Use the last or last several digits
to show the band features and
position of the antenna port.
Fill other digits that are not
used with a random code.
B - 1. Single-band Antenna
B - 2. Dual-band Antenna
B - 3. Tri-band Antenna
B - 5. Penta-band Antenna
B - 6. Hexa-band Antenna
B - 7. Multi-beam Antenna
B - 8. TDD Antenna
B - 9. Cluster Antenna
C - 1. RET System
C Antenna Information
Management
C - 2. Intelligent Management
D - 1. TMA
D - 2. Combiner
E - 1. Bracket
E Bracket&Installation
Guide
E - 2. Installation Guide
Index of Antenna and Antenna Line Product
The products are listed in an alphabetical & numeric order. New or changed product.
A704515R0 27 ADU4517R0v01 59
Antenna Information
ATR4517R0 137 ATADU2003 305
Management
Model Page
A-1 AAU3961 1
A-2 AAU3940 2
A-3 AAU3920 3
A-4 AAU3911 4
A-5 AAU3910 5
Model: AAU3961
AAU
Product Description
AAU3961
TX/RX 4T4R
EIRP 4*63dBm
Dimensions (H x W x D) 1550mm(H)*370mm(W)*230mm(D)
Temperature - 40℃~50℃
1
Model: AAU3940
Product Description
AAU3940
TX/RX 2T2R
EIRP 2*58.8dBm
Weight 15kg
Power Type AC / DC DC
2
Model: AAU3920
AAU
Product Description
AAU3920
TX/RX 2T4R
EIRP 2*66.5dBm
Dimensions (H x W x D) 1450mm(H)*320mm(W)*188mm(D)
Weight 35kg
Temperature - 40℃~55℃
3
Model: AAU3911
Product Description
AAU3911
TX/RX 2T4R
EIRP 2*64.8dBm
Dimensions (H x W x D) 2020mm(H)*359mm(W)*290mm(D)
Temperature - 40℃~55℃
4
Model: AAU3910
AAU
Product Description
AAU3910
TX/RX 2T4R
EIRP 2*65.3dBm
Dimensions (H x W x D) 1450mm(H)*320mm(W)*230mm(D)
Temperature - 40℃~55℃
5
B. Passive Antenna
Single-band
B - 1. Single-band Antenna
790-960 65 16.5 0-12 MET1.0 2 x 7/16 DIN-F 1936 x 259 x 135 A79451600v02 13 A
790-960 65 16.5 0-12 EasyRET2.0 2 x 7/16 DIN-F 1936 x 259 x 135 A794516R0 15 A
790-960 65 17.5 0-10 MET1.0 2 x 7/16 DIN-F 2535 x 259 x 135 A79451700v02 17 A
790-960 65 17.5 0-10 EasyRET2.0 2 x 7/16 DIN-F 2535 x 259 x 135 A794517R0 19 A
690-960 65 16.5 0-12 EasyRET2.0 2 x 7/16 DIN-F 1936 x 298 x 149 A704516R0 29 A
690-960 65 17.5 0-10 EasyRET2.0 2 x 7/16 DIN-F 2535 x 298 x 149 A704517R0 31 A
690-960 33 20.5 0-10 EasyRET2.0 2 x 7/16 DIN-F 2580 x 590 x 169 A704521R0 33 A
** Preliminary Issue
r b y
DX-790-960-65-15i-M
Model: A79451500v01
Antenna Specifications
Single-band
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable
at mid Tilt 14.6 14.8 15.1
Gain (dBi)
over all Tilts 14.5 ± 0.3 14.8 ± 0.3 15.1 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 17
lobe above main beam (Typ.) (dB)
Horizontal 3dB beam width (°) 68 ± 1.4 67 ± 1.6 65 ± 2.3
Vertical 3dB beam width (°) 16.0 ± 0.8 15.3 ± 0.7 14.5 ± 0.8
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio (dB) > 25 > 24 > 24
Cross polar ratio (dB) 0° > 25 > 25 > 25
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1356 x 259 x 135
Packing dimensions (H x W x D) (mm) 1640 x 305 x 190
Antenna weight (kg) 11.2
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 19.4 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 440 (at 150 km/h)
Wind load (N) Lateral: 230 (at 150 km/h)
Rear side: 585 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
9
DX-790-960-65-15i-M
Model: A79451500v01
56
Unit: mm
70
790 - 960
X
+45° -45°
10
DX-790-960-65-15i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU-1.4m
Model: A794515R0
Antenna Specifications
Single-band
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable
at mid Tilt 14.6 14.8 15.1
Gain (dBi)
over all Tilts 14.5 ± 0.3 14.8 ± 0.3 15.1 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 1.4 67 ± 1.6 65 ± 2.3
Vertical 3dB beam width (°) 16.0 ± 0.8 15.3 ± 0.7 14.5 ± 0.8
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30°(dB) > 25 > 24 > 24
Cross polar ratio (dB) 0° > 25 > 25 > 25
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1356 x 259 x 135
Packing dimensions (H x W x D) (mm) 1635 x 300 x 190
Antenna weight (kg) 10.8
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 17.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 440 (at 150 km/h)
Wind load (N) Lateral: 230 (at 150 km/h)
Rear side: 585 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
11
DX-790-960-65-15i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU-1.4m
Model: A794515R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r - Red r
12
DX-790-960-65-16.5i-M
Model: A79451600v02
Antenna Specifications
Single-band
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 16.3 16.5 16.8
Gain (dBi)
over all Tilts 16.2 ± 0.4 16.4 ± 0.4 16.6 ± 0.4
Side lobe suppression for first side
> 17 > 17 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 1.2 68 ± 1.8 65 ± 2.6
Vertical 3dB beam width (°) 10.1 ± 0.6 9.8 ± 0.5 9.2 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1936 x 259 x 135
Packing dimensions (H x W x D) (mm) 2255 x 305 x 190
Antenna weight (kg) 12.9
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 20.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 665 (at 150 km/h)
Wind load (N) Lateral: 345 (at 150 km/h)
Rear side: 880 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0B01 Mechanical downtilt: 0 - 12 ° 1.3 kg 1 (Separate packing)
13
DX-790-960-65-16.5i-M
Model: A79451600v02
56
70 Unit: mm
790 - 960
X
+45° -45°
14
DX-790-960-65-16.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU-2.0m
Model: A794516R0
Antenna Specifications
Single-band
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 16.3 16.5 16.8
Gain (dBi)
over all Tilts 16.2 ± 0.4 16.4 ± 0.4 16.6 ± 0.4
Side lobe suppression for first side
> 17 > 17 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 1.2 68 ± 1.8 65 ± 2.6
Vertical 3dB beam width (°) 10.1 ± 0.6 9.8 ± 0.5 9.2 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ±30° (dB) > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1936 x 259 x 135
Packing dimensions (H x W x D) (mm) 2255 x 305 x 190
Antenna weight (kg) 13.5
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 22.6 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1936
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 12 ° 2.1 kg 1 (Separate packing)
15
DX-790-960-65-16.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU-2.0m
Model: A794516R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r
r - Red
16
DX-790-960-65-17.5i-M
Model: A79451700v02
Antenna Specifications
Single-band
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 17.1 17.3 17.6
Gain (dBi)
over all Tilts 16.9 ± 0.4 17.1 ± 0.3 17.4 ± 0.5
Side lobe suppression for first side
> 18 > 18 > 19
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 1.2 68 ± 1.3 65 ± 3.0
Vertical 3dB beam width (°) 8.3 ± 0.5 7.9 ± 0.5 7.3 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 26 > 26 > 26
Cross polar ratio (dB) 0° > 25 > 25 > 25
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 259 x 135
Packing dimensions (H x W x D) (mm) 2815 x 305 x 190
Antenna weight (kg) 15.6
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 25.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 910 (at 150 km/h)
Wind load (N) Lateral: 470 (at 150 km/h)
Rear side: 1200 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
17
DX-790-960-65-17.5i-M
Model: A79451700v02
56
70
Unit: mm
790 - 960
X
+45° -45°
18
DX-790-960-65-17.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU-2.6m
Model: A794517R0
Single-band
Antenna Specifications
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 17.1 17.3 17.6
Gain (dBi)
over all Tilts 16.9 ± 0.4 17.1 ± 0.3 17.4 ± 0.5
Side lobe suppression for first side
> 18 > 18 > 19
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 1.2 68 ± 1.3 65 ± 3.0
Vertical 3dB beam width (°) 8.3 ± 0.5 7.9 ± 0.5 7.3 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ±30° (dB) > 26 > 26 > 26
Cross polar ratio (dB) 0° > 25 > 25 > 25
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 259 x 135
Packing dimensions (H x W x D) (mm) 2810 x 300 x 190
Antenna weight (kg) 16.5
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 26.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
2535
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 8 ° 2.1 kg 1 (Separate packing)
19
DX-790-960-65-17.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU-2.6m
Model: A794517R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r
r - Red
20
DX-790-960-90-15i-M
Model: A79451503
Single-band
Antenna Specifications
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 15.0 15.2 15.3
Gain (dBi)
over all Tilts 14.8 ± 0.3 15.0 ± 0.3 15.0 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 86 ± 1.0 85 ± 1.0 85 ± 1.5
Vertical 3dB beam width (°) 10.0 ± 0.4 9.8 ± 0.4 9.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30°(dB) > 24 > 24 > 24
Cross polar ratio (dB) 0° > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1936 x 259 x 135
Packing dimensions (H x W x D) (mm) 2255 x 305 x 190
Antenna weight (kg) 13.5
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 22.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 665 (at 150 km/h)
Wind load (N) Lateral: 345 (at 150 km/h)
Rear side: 880 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
21
DX-790-960-90-15i-M
Model: A79451503
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20S11 Remote electrical tilt module, a couple of AISG connectors 0.4 kg 1 (Separate packing)
174 106
Unit: mm
1936
1285
790 - 960
X
+45° -45°
22
DX-790-960-90-15i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.0m
Model: A794515R1
Antenna Specifications
Single-band
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 15.0 15.2 15.3
Gain (dBi)
over all Tilts 14.8 ± 0.3 15.0 ± 0.3 15.0 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 86 ± 1.0 85 ± 1.0 85 ± 1.5
Vertical 3dB beam width (°) 10.0 ± 0.4 9.8 ± 0.4 9.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ±30°(dB) > 24 > 24 > 24
Cross polar ratio (dB) 0° > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available. 106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1936 x 259 x 135
Packing dimensions (H x W x D) (mm) 2255 x 305 x 190
Antenna weight (kg) 13.7
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 22.6 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1936
1285
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 12 ° 2.1 kg 1 (Separate packing)
23
DX-790-960-90-15i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.0m
Model: A794515R1
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r
r - Red
24
DX-790-960-90-17i-M
Model: A79451702
Antenna Specifications
Single-band
Electrical Properties
790 - 960
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 15.8 16.1 16.3
Gain (dBi)
over all Tilts 15.7 ± 0.3 16.0 ± 0.3 16.2 ± 0.4
Side lobe suppression for first side
> 16 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 86 ± 1.0 85 ± 1.0 85 ± 1.5
Vertical 3dB beam width (°) 8.3 ± 0.4 7.9 ± 0.5 7.4 ± 0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30°(dB) > 25 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 259 x 135
Packing dimensions (H x W x D) (mm) 2810 x 300 x 190
Antenna weight (kg) 16.6
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 26.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 910 (at 150 km/h)
Wind load (N) Lateral: 470 (at 150 km/h)
Rear side: 1200 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 8 ° 2.1 kg 1 (Separate packing)
25
DX-790-960-90-17i-M
Model: A79451702
56
70 Unit: mm
790 - 960
X
+45° -45°
26
DX-690-960-65-15i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 1.4m
Model: A704515R0
Antenna Specifications
Single-band
Electrical Properties
690 - 960
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable
at mid Tilt 13.9 14.4 14.6 14.8
Gain (dBi)
over all Tilts 13.9 ± 0.3 14.3 ± 0.3 14.5 ± 0.3 14.7 ± 0.4
Side lobe suppression for first side
> 15 > 15 > 15 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 1.4 68 ± 1.0 67 ± 1.0 65 ± 2.0
Vertical 3dB beam width (°) 16.4 ± 1.0 15.0 ± 1.0 14.5 ± 0.7 13.2 ± 0.9
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 24 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 17 > 17 > 17 > 17
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
27
DX-690-960-65-15i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 1.4m
Model: A704515R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r - Red r
28
DX-690-960-65-16.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.0m
Model: A704516R0
Antenna Specifications
Single-band
Electrical Properties
690 - 960
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 15.5 15.9 16.1 16.4
Gain (dBi)
over all Tilts 15.4 ± 0.3 15.7 ± 0.4 15.9 ± 0.5 16.1 ± 0.5
Side lobe suppression for first side
> 15 > 15 > 15 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 1.0 68 ± 1.2 67 ± 1.2 65 ± 1.8
Vertical 3dB beam width (°) 11.3 ± 0.8 10.3 ± 0.5 9.8 ± 0.6 9.2 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 24 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
29
DX-690-960-65-16.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.0m
Model: A704516R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r - Red r
30
DX-690-960-65-17.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.6m
Model: A704517R0
Antenna Specifications
Single-band
Electrical Properties
690 - 960
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 16.5 16.7 17.0 17.2
Gain (dBi)
over all Tilts 16.4 ± 0.3 16.6 ± 0.4 16.7 ± 0.4 16.9 ± 0.5
Side lobe suppression for first side
> 17 > 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 1.0 68 ± 1.2 67 ± 1.2 65 ± 2.0
Vertical 3dB beam width (°) 8.7 ± 0.6 8.0 ± 0.5 7.7 ± 0.4 7.2 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 25 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 298 x 149
Packing dimensions (H x W x D) (mm) 2885 x 365 x 235
Antenna weight (kg) 19.5
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 32.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
2535
1874
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 8 ° 2.1 kg 1 (Separate packing)
31
DX-690-960-65-17.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.6m
Model: A704517R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r
r - Red
32
DX-690-960-33-20.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.6m
Model: A704521R0
Antenna Specifications
Single-band
Electrical Properties
690 - 960
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 19.1 19.7 20.0 20.3
Gain (dBi)
over all Tilts 19.0 ± 0.5 19.6 ± 0.4 19.9 ± 0.5 20.2 ± 0.3
Side lobe suppression for first side
> 19 > 21 > 21 > 19
lobe above main beam (dB)
Azimuth side lobe suppression(dB) > 18 > 18 > 19 > 19
Horizontal 3dB beam width (°) 35 ± 1.5 32.5 ± 1.0 31.5 ± 1.5 29 ± 1.0
Vertical 3dB beam width (°) 8.8 ± 0.5 8.0 ± 0.5 7.7 ± 0.3 7.2 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 30
Front to back ratio , ± 30°(dB) > 32 > 35 > 33 > 32
Cross polar ratio (dB) 0° > 21 > 28 > 26 > 24
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2580 x 590 x 169 144
Packing dimensions (H x W x D) (mm) 2875 x 770 x 300
Antenna weight (kg) 45
Clamps weight (kg) 5.8 (2 units)
Antenna packing weight (kg) 64.4 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
2580
Accessories
Item Model Description Weight Units per antenna
33
DX-690-960-33-20.5i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 2.6m
Model: A704521R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
r
r - Red
34
DX-1710-2170-90-17i-M
Model: A19451703
Antenna Specifications
Single-band
Electrical Properties
Frequency range (MHz) 1710 - 1880 1850 - 1990 1920 - 2170
Polarization +45° , -45°
VSWR ≤ 1.4
(°) 2 6 10 2 6 10 2 6 10
Gain
(dBi) 16.3 16.5 16.2 16.5 16.7 16.4 16.7 17.0 16.5
Side lobe suppression for first (°) 2 6 10 2 6 10 2 6 10
side lobe above horizon (dB) 18 17 16 18 17 16 18 17 16
Horizontal 3dB beam width (°) 84 88 86
Vertical 3dB beam width (°) 7.5 6.5 6.0
Isolation between ports (dB) ≥ 30
Front to back ratio, copolar (dB) ≥ 25
0° ≥ 18
Cross polar ratio (dB)
± 60° ≥ 10
Electrical downtilt (°) 2 - 10
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Max. CW input power (W) 300
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Dimensions (H x W x D) (mm) 1306 x 155 x 79
Packing dimensions (H x W x D) (mm) 1770 x 260 x 160
Net weight (kg) 6.5
Bracket weight (kg) 3.0
Packing weight (kg) 11.8
Mechanical downtilt (°) 0 - 16
Mast diameter (mm) 50 - 115
Radome material Fiberglass
Operating temperature (℃) -55 - +65
1710 - 2170
Wind load frontal (N) 150 (v=150 km/h)
Wind load lateral (N) 110 (v=150 km/h)
X
Wind load rear side (N) 225 (v=150 km/h)
Max. wind velocity (km/h) 200
+45° -45°
Connector 2 x 7/16 DIN Female
35
DX-1710-2170-33-21i-M
Model: A19452101
Antenna Specifications
Electrical Properties
Frequency range (MHz) 1710 - 1880 1850 - 1990 1920 - 2170
Polarization +45° , -45°
VSWR ≤ 1.45
(°) 2 6 10 2 6 10 2 6 10
Gain
(dBi) 20.0 20.1 20.1 20.3 20.5 20.1 20.7 20.5 19.8
Side lobe suppression for first (°) 2 6 10 2 6 10 2 6 10
side lobe above horizon (dB) 18 17 16 18 17 16 18 17 16
Horizontal 3dB beam width (°) 35 33 31
Vertical 3dB beam width (°) 7.2 6.6 6.2
Isolation between ports (dB) ≥ 30
Front to back ratio, copolar (dB) Typ. 28
Cross polar ratio (dB) Typ. 20
Electrical downtilt (°) 2 - 10
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Max. CW input power (W) 300
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Dimensions (H x W x D) (mm) 1318 x 289 x 85
Packing dimensions (H x W x D) (mm) 1662 x 405 x 175
Net weight (kg) 11.4
Bracket weight (kg) 4.6
Packing weight (kg) 18.4
Mechanical downtilt (°) 0-8
Mast diameter (mm) 50 - 115 1710 - 2170
Radome material Fiberglass X
Operating temperature (℃) -55 - +65
Wind load frontal (N) 285 (v=150 km/h) +45° -45°
Wind load lateral (N) 120 (v=150 km/h)
Wind load rear side (N) 425 (v=150 km/h)
Max. wind velocity (km/h) 200
7/16 (F) 7/16 (F)
Connector 2 x 7/16 DIN Female
36
DX-1710-2200-65-15.5i-M
Model: A19451505
Antenna Specifications
Single-band
Electrical Properties
1710 - 2200
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 15.4 15.5 15.7 15.7
Gain (dBi)
over all Tilts 15.3 ±0.3 15.4 ±0.3 15.6 ±0.4 15.6 ±0.3
Side lobe suppression for first side
> 17 > 18 > 18 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ±2.6 64 ±2 61 ±3.3 60 ±1.8
Vertical 3dB beam width (°) 13.9 ±0.7 13.0 ±0.5 12.6 ±0.8 11.5 ±0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 25 > 25 > 24 > 24
Cross polar ratio (dB) 0° > 22 > 22 > 22 > 22
Max. power per input (W) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 702 x 155 x 89
Packing dimensions (H x W x D) (mm) 1025 x 195 x 155
Antenna weight (kg) 4.3
Clamps weight (kg) 2.0 (2 units)
Antenna packing weight (kg) 7.8 (Included clamps)
Mast diameter supported (mm) 38 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 150 (at 150 km/h)
Wind load (N) Lateral: 75 (at 150 km/h)
Rear side: 175 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
37
DX-1710-2200-65-15.5i-M
Model: A19451505
34
46 34 Unit: mm
1710 - 2200
X
+45°
-45°
38
DX-1710-2200-65-18i-M
Model: A19451811v01
Antenna Specifications
Single-band
Electrical Properties
1710 - 2200
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 17.4 17.8 18.0 17.9
Gain (dBi)
over all Tilts 17.2 ± 0.4 17.6 ± 0.4 17.7 ± 0.4 17.8 ± 0.4
Side lobe suppression for first side
> 19 > 19 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 1.5 67 ± 1.5 66 ± 2 63 ± 2
Vertical 3dB beam width (°) 7.4 ± 0.4 6.9 ± 0.4 6.5 ± 0.4 6.0 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 155 x 89
Packing dimensions (H x W x D) (mm) 1695 x 195 x 155
Antenna weight (kg) 6.1
Clamps weight (kg) 2.0 (2 units)
Antenna packing weight (kg) 10.6 (Included clamps)
Mast diameter supported (mm) 38 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 330 (at 150 km/h)
Wind load (N) Lateral: 165 (at 150 km/h)
Rear side: 375 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
39
DX-1710-2200-65-18i-M
Model: A19451811v01
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20S11 Remote electrical tilt module, a couple of AISG connectors 0.4 kg 1 (Separate packing)
64
60
Unit: mm
1392
1424
1365
1710 - 2200
X
+45° -45°
40
DX-1710-2200-65-18i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 1.4m
Model: A194518R0v01
Antenna Specifications
Single-band
Electrical Properties
1710 - 2200
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 17.4 17.8 18.0 17.9
Gain (dBi)
over all Tilts 17.2 ± 0.4 17.6 ± 0.4 17.7 ± 0.4 17.8 ± 0.4
Side lobe suppression for first side
> 19 > 19 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 1.5 67 ± 1.5 66 ± 2 63 ± 2
Vertical 3dB beam width (°) 7.4 ± 0.4 6.9 ± 0.4 6.5 ± 0.4 6.0 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 28 > 28 > 27 > 27
Cross polar ratio (dB) 0° > 22 > 22 > 22 > 18
Max. power per input (W) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
41
DX-1710-2200-65-18i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 1.4m
Model: A194518R0v01
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...b
b
b - Blue
42
DX-1710-2200-65-19.5i-M
Model: A19451902
Antenna Specifications
Single-band
Electrical Properties
1710 - 2200
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 6 , continuously adjustable
at mid Tilt 18.7 19.1 19.4 19.5
Gain (dBi)
over all Tilts 18.6 ±0.4 19.0 ±0.5 19.2 ±0.4 19.2 ±0.5
Side lobe suppression for first side
> 17 > 17 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ±2.5 64 ±1.8 62 ±4.3 60 ±1.0
Vertical 3dB beam width (°) 5.0 ±0.3 4.7 ±0.2 4.5 ±0.3 4.1 ±0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 27 > 27 > 27 > 27
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 25
Max. power per input (W) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1954 x 155 x 89
Packing dimensions (H x W x D) (mm) 2280 x 195 x 155
Antenna weight (kg) 8.4
Clamps weight (kg) 2.0 (2 units)
Antenna packing weight (kg) 13.1 (Included clamps)
Mast diameter supported (mm) 38 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 505 (at 150 km/h)
Wind load (N) Lateral: 250 (at 150 km/h)
Rear side: 575 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
43
DX-1710-2200-65-19.5i-M
Model: A19451902
34
46 34 Unit: mm
1710 - 2200
X
+45°
-45°
44
DX-1710-2690-65-16i-M
Model: A26451500
Antenna Specifications
Single-band
Electrical Properties
1710 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable
at mid Tilt 15.2 16.0 16.3 16.1
Gain (dBi)
over all Tilts 15.2 ± 0.5 15.9 ± 0.5 16.2 ± 0.5 16.0 ± 0.5
Side lobe suppression for first side
> 18 > 18 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ± 2.5 64 ± 4.6 60 ± 3.4 60 ± 3.6
Vertical 3dB beam width (°) 12.0 ± 0.9 11.0 ± 0.9 9.6 ± 0.9 8.6 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Front to back ratio, ±30° (dB) > 24 > 24 > 24 > 24
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 841 x 155 x 109
Packing dimensions (H x W x D) (mm) 1175 x 210 x 190
Antenna net weight (kg) 5.5
Clamps weight (kg) 2.0 (2 units)
Antenna packing weight (kg) 10.0 (Included clamps)
Mast diameter supported (mm) 38 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 120 (at 150 km/h)
Wind load (N) Lateral: 110 (at 150 km/h)
Rear side: 215 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
45
DX-1710-2690-65-16i-M
Model: A26451500
56
Unit: mm
57
1710 - 2690
X
+45°
-45°
46
DX-1710-2690-65-18i-M
Model: A26451800v02
Antenna Specifications
Single-band
Electrical Properties
1710 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 17.4 18.0 18.5 18.6
Gain (dBi)
over all Tilts 17.2 ±0.3 17.6 ±0.5 18.3 ±0.4 18.4 ±0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ±2.0 65 ±2.4 62 ±2.7 60 ±1.5
Vertical 3dB beam width (°) 6.8 ±0.4 6.1 ±0.4 5.5 ±0.4 5.0 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 28 > 29 > 29 > 29
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 155 x 89
Packing dimensions (H x W x D) (mm) 1695 x 195 x 155
Antenna weight (kg) 6.9
Clamps weight (kg) 2.0 (2 units)
Antenna packing weight (kg) 11.4 (included clamps)
Mast diameter supported (mm) 38 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 330 (at 150 km/h)
Wind load (N) Lateral: 165 (at 150 km/h)
Rear side: 375 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
47
DX-1710-2690-65-18i-M
Model: A26451800v02
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20S11 Remote electrical tilt module, a couple of AISG connectors 0.4 kg 1 (Separate packing)
60 64
Unit: mm
1392
1424
1365
1710 - 2690
X
+45° -45°
48
DX-1710-2690-65-18i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 1.4m
Model: A264518R0v01
Antenna Specifications
Single-band
Electrical Properties
1710 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable
at mid Tilt 17.4 18.0 18.5 18.6
Gain (dBi)
over all Tilts 17.2 ±0.3 17.6 ±0.5 18.3 ±0.4 18.4 ±0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ±2.0 65 ±2.4 62 ±2.7 60 ±1.5
Vertical 3dB beam width (°) 6.8 ±0.4 6.1 ±0.4 5.5 ±0.4 5.0 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 28 > 29 > 29 > 29
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
49
DX-1710-2690-65-18i-M-R
EasyRET Single-Band Antenna with 1 Integrated RCU - 1.4m
Model: A264518R0v01
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...y
y
y - Yellow
50
DX-450-470-65-15i-0F
Model: A45451500
Antenna Specifications
Single-band
Electrical Properties
Frequency range (MHz) 450 - 470
Polarization +45° , -45°
VSWR ≤ 1.5
Gain (dBi) 15
Horizontal 3dB beam width (°) 65
Vertical 3dB beam width (°) 16
Isolation between ports (dB) ≥ 30
Front to back ratio, copolar (dB) ≥ 25
Cross polar ratio (dB) ≥ 15
Electrical downtilt (°) 0
Intermodulation IM5 (dBc) ≤ -160 (2 x 43 dBm carrier)
Max. CW input power (W) 500
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Dimensions (H x W x D) (mm) 2042 x 486 x 98
Packing dimensions (H x W x D) (mm) 2267 x 598 x 269
Net weight (kg) 28.3
Bracket weight (kg) 6.5
Packing weight (kg) 41.6
Mechanical downtilt (°) 0 - 16
Mast diameter (mm) 50 - 115
Radome material Fiberglass
450 - 470
Operating temperature (℃) -55 - +65
X
Wind load frontal (N) 740 (v=150 km/h)
Wind load lateral (N) 220 (v=150 km/h)
Wind load rear side (N) 1100 (v=150 km/h)
+45° -45°
Max. wind velocity (km/h) 200
Connector 2 x 7/16 DIN Female
7/16 (F) 7/16 (F)
51
B - 2. Dual-band Antenna
Dual-band
Gain (dBi) Tilt Method Connector Dimension (mm) Model Page
Range (MHz) beam width (°) downtilt (°) Symbol
790-862/
880-960
65/65 14.5/15 0-14/0-14 EasyRET2.0 4 x 7/16 DIN-F 1490 x 298 x 150 ADU4515R0v01 55 D
790-862/
880-960
65/65 16/16.5 0-12/0-12 EasyRET2.0 4 x 7/16 DIN-F 1999 x 259 x 150 ADU4516R0v01 57 D
790-862/
880-960
65/65 17/17.5 0-10/0-10 EasyRET2.0 4 x 7/16 DIN-F 2538 x 259 x 150 ADU4517R0v01 59 D
690-960/
690-960
65/65 15/15 0-14/0-14 EasyRET2.0 4 x 7/16 DIN-F 1499 x 429 x 196 **ADU4515R5 61 E
790-960/
790-960
65/65 16/16 0-10/0-10 EasyRET2.0 4 x 7/16 DIN-F 1999 x 429 x 196 **ADU4516R7 62 E
690-960/
690-960
65/65 16/16 0-12/0-12 EasyRET2.0 4 x 7/16 DIN-F 2099 x 429 x 196 **ADU4516R6 64 E
690-960/
690-960
65/65 17/17 0-10/0-10 EasyRET2.0 4 x 7/16 DIN-F 2769 x 429 x 196 **ADU4517R6 65 E
790-960/
1710-2180
65/65 15/17.5 0-14/0-10 MET1.0 4 x 7/16 DIN-F 1360 x 259 x 135 ADU451503 66 F
790-960/
1710-2180
65/65 15/17.5 0-14/0-10 EasyRET2.0 4 x 7/16 DIN-F 1360 x 259 x 135 ADU4517R3 68 F
790-960/
1710-2180
65/65 16.5/18.5 0-12/0-8 MET1.0 4 x 7/16 DIN-F 1936 x 259 x 135 ADU451602v01 70 F
790-960/
1710-2180
65/65 16.5/18.5 0-12/0-8 EasyRET1.0 4 x 7/16 DIN-F 1936 x 259 x 135 ADU4518R3 72 F
790-960/
1710-2180
65/65 17.5/18.5 0-10/0-8 MET1.0 4 x 7/16 DIN-F 2535 x 259 x 135 ADU451807v01 74 F
790-960/
1710-2180
65/65 17.5/18.5 0-10/0-8 EasyRET1.0 4 x 7/16 DIN-F 2535 x 259 x 135 ADU4518R0 76 F
790-960/ MET1.0+
1710-2180
65/65 15/17.5 0-14/0-10
Combiner
2 x 7/16 DIN-F 1360 x 259 x 135 ADU4517C0 78 F
790-960/ MET1.0+
1710-2180
65/65 16.5/18.5 0-12/0-8
Combiner
2 x 7/16 DIN-F 1936 x 259 x 135 ADU4518C1 80 F
790-960/ MET1.0+
1710-2180
65/65 17.5/18.5 0-10/0-8
Combiner
2 x 7/16 DIN-F 2535 x 259 x 135 ADU4518C0 82 F
790-960/
1710-2180
65/65 17.5/18 0-10/0-10 MET1.0 4 x 7/16 DIN-F 2535 x 259 x 135 ADU451720 84 F
790-960/
1710-2690
65/65 15/17.5 0-15/2-12 MET2.0 4 x 7/16 DIN-F 1499 x 259 x 135 ADU451716v01 86 G
790-960/
1710-2690
65/65 15/17.5 0-15/2-12 EasyRET2.0 4 x 7/16 DIN-F 1499 x 259 x 135 ADU4518R10 88 G
790-960/
1710-2690
65/65 16/18 0-12/2-12 MET2.0 4 x 7/16 DIN-F 2087 x 259 x 135 ADU451604v01 90 G
B - 2. Dual-band Antenna
790-960/
1710-2690
65/65 16/18 0-12/2-12 EasyRET2.0 4 x 7/16 DIN-F 2087 x 259 x 135 ADU4518R11 92 G
790-960/
1710-2690
65/65 17/18 0-10/2-12 MET2.0 4 x 7/16 DIN-F 2555 x 259 x 135 ADU451712v01 94 G
790-960/
1710-2690
65/65 17/18 0-10/2-12 EasyRET2.0 4 x 7/16 DIN-F 2555 x 259 x 135 ADU4518R12 96 G
690-960/
1710-2690
65/65 15/17.5 0-15/2-12 EasyRET2.0 4 x 7/16 DIN-F 1499 x 259 x 135 ADU4518R9 98 G
690-960/
1710-2690
65/65 16/18 0-12/2-12 EasyRET2.0 4 x 7/16 DIN-F 2087 x 259 x 135 ADU4518R7 100 G
690-960/
1710-2690
65/65 17/18 0-10/2-12 EasyRET2.0 4 x 7/16 DIN-F 2555 x 259 x 135 ADU4518R8 102 G
1710-2200/
1710-2200
65/65 18/18 0-10/0-10 MET2.0 4 x 7/16 DIN-F 1365 x 269 x 86 ADU451819v01 104 H
1710-2200/
1710-2200
65/65 18/18 0-10/0-10 EasyRET2.0 4 x 7/16 DIN-F 1365 x 269 x 86 ADU4518R1v01 106 H
1710-2200/
1710-2200
65/65 19.5/19.5 0-6/0-6 MET1.0 4 x 7/16 DIN-F 1954 x 323 x 89 ADU451902 108 H
1710-2170/
2490-2690
65/65 18/18 0-12/0-12 EasyRET1.0 4 x 7/16 DIN-F 1490 x 155 x 109 ADU4518R5 110 J
1710-2690/
1710-2690
65/65 16/16 0-14/0-14 MET1.0 4 x 7/16 DIN-F 840 x 299 x 109 ADU451507 112 I
1710-2690/
1710-2690
65/65 18/18 0-12/0-12 MET2.0 4 x 7/16 DIN-F 1365 x 269 x 86 ADU451816v02 114 I
1710-2690/
1710-2690
65/65 18/18 0-12/0-12 EasyRET2.0 4 x 7/16 DIN-F 1365 x 269 x 86 ADU4518R6v01 116 I
** Preliminary Issue
r r
2 Filtered low-bands Low-bands array High-bands array High-bands array 2 Filtered high-bands
(Dipole reuse) side-by-side side-by-side side-by-side (Dipole reuse)
DXX-790-862/880-960-65/65-14.5i/15i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4515R0v01
Antenna Specifications
Electrical Properties
Frequency range (MHz) 790 - 862 880 - 960
Polarization +45° , -45°
Dual-band
Electrical downtilt (°) 0 - 14 , continuously adjustable, each band separately
at mid Tilt 14.3 14.8
Gain (dBi)
over all Tilts 14.2 ± 0.3 14.7 ± 0.3
Side lobe suppression for first side
> 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 2.0 61 ± 2.0
Vertical 3dB beam width (°) 13.5 ± 0.8 12.1 ± 0.8
VSWR < 1.5
Cross polar isolation (dB) ≥ 30 ≥ 30
Interband isolation (dB) ≥ 30
Front to back ratio, ± 30° (dB) > 24 > 23
Cross polar ratio (dB) 0° > 25 > 23
Max. power per input (W) 400 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1490 x 298 x 150
Packing dimensions (H x W x D) (mm) 1820 x 360 x 230
Antenna weight (kg) 18.0
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 27.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1490
Accessories
Item Model Description Weight Units per antenna
55
DXX-790-862/880-960-65/65-14.5i/15i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4515R0v01
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx…..rr
r rr
r - Red
56
DXX-790-862/880-960-65/65-16i/16.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4516R0v01
Antenna Specifications
Electrical Properties
Frequency range (MHz) 790 - 862 880 - 960
Polarization +45° , -45°
Dual-band
Electrical downtilt (°) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 15.8 16.3
Gain (dBi)
over all Tilts 15.6 ± 0.3 16.0 ± 0.3
Side lobe suppression for first side
> 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 2.0 65 ± 2.0
Vertical 3dB beam width (°) 10.5 ± 0.5 9.4 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30 ≥30
Interband isolation (dB) ≥ 30
Front to back ratio, ± 30° (dB) > 24 > 24
Cross polar ratio (dB) 0° > 25 > 26
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1999 x 259 x 150
Packing dimensions (H x W x D) (mm) 2290 x 305 x 205
Antenna weight (kg) 21.7
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 30.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1887
1999
Accessories
Item Model Description Weight Units per antenna
57
DXX-790-862/880-960-65/65-16i/16.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4516R0v01
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx…..rr
r rr
r - Red
58
DXX-790-862/880-960-65/65-17i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4517R0v01
Antenna Specifications
Electrical Properties
Frequency range (MHz) 790 - 862 880 - 960
Polarization +45° , -45°
Dual-band
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 16.8 17.3
Gain (dBi)
over all Tilts 16.5 ± 0.4 17.1 ± 0.5
Side lobe suppression for first side
> 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 2.0 65 ± 2.0
Vertical 3dB beam width (°) 8.3 ± 0.6 7.2 ± 0.6
VSWR < 1.5
Cross polar isolation (dB) ≥ 30 ≥ 30
Interband isolation (dB) ≥ 30
Front to back ratio, ± 30° (dB) > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2538 x 259 x 150
Packing dimensions (H x W x D) (mm) 2960 x 305 x 205
Antenna weight (kg) 25.5
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 36.8 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
2538
Accessories
59
DXX-790-862/880-960-65/65-17i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4517R0v01
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx…..rr
r rr
r - Red
60
DXX-690-960/690-960-65/65-14.5i/14.5i-M/M-R
EasyRET Dual-Band Antenna with Integrated RCUs - 1.4m
Model: ADU4515R5
Preliminary Issue
Antenna Specifications
Electrical Properties
Dual-band
Electrical downtilt (°) 0 - 14
Mechanical Properties
61
DXX-790-960/790-960-65/65-16i/16i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4516R7
Preliminary Issue
Antenna Specifications
Electrical Properties
2 x (790 - 960)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 15.5 15.8 16.0
Gain (dBi)
over all Tilts 15.3 ±0.5 15.6 ±0.5 15.8 ±0.5
Side lobe suppression for first side
> 20 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ±5.0 65 ±5.0 60 ±5.0
Vertical 3dB beam width (°) 9.5 ± 0.8 9.2 ± 0.7 8.5 ± 0.7
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ± 30° (dB) > 24 > 25 > 26
Cross polar ratio (dB) 0° > 17 > 17 > 18
Max. power per input (W) 400 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1999 x 429 x 196
Packing dimensions (H x W x D) (mm) 2195 x 530 x 270
Antenna weight (kg) 28.8
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 42.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 910 (at 150 km/h)
Wind load (N) Lateral: 265 (at 150 km/h)
Rear side: 910 (at 150 km/h)
1273
1999
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0D01 Mechanical downtilt: 0 - 12 ° 2.1 kg 1 (Separate packing)
62
DXX-790-960/790-960-65/65-16i/16i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4516R7
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Dual-band
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The
protocol of RET antenna software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor
defined command. For more details about protocol switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx……Lr1
HWMxxx……Rr2 Lr1 Rr2
r - Red
L - Left array R - Right array
63
DXX-690-960/690-960-65/65-16i/16i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4516R6
Preliminary Issue
Antenna Specifications
Electrical Properties
Mechanical Properties
64
DXX-690-960/690-960-65/65-17i/17i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4517R6
Preliminary Issue
Antenna Specifications
Electrical Properties
Dual-band
Frequency range (MHz) 2 x (690 - 960)
Mechanical Properties
65
DXX-790-960/1710-2180-65/65-15i/17.5i-M/M
Model: ADU451503
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable 0 - 10 , continuously adjustable
at mid Tilt 14.6 15.0 15.1 16.8 17.3 17.6
Gain (dBi)
over all Tilts 14.5 ±0.3 14.8 ±0.3 14.9 ±0.4 16.7 ±0.4 17.1 ±0.6 17.4 ±0.6
Side lobe suppression for first side
> 18 > 17 > 16 > 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±3.0 66 ±4.1 64 ±3.2 65 ±2.0 63 ±2.2 60±3.2
Vertical 3dB beam width (°) 15.7 ±0.8 15.0 ±0.6 14.0 ±0.7 7.6 ±0.4 7.1 ±0.4 6.6 ±0.7
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 40 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 24 > 24 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1360 x 259 x 135
Packing dimensions (H x W x D) (mm) 1640 x 305 x 190
Antenna weight (kg) 13.7
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 20.4 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 440 (at 150 km/h)
Wind load (N) Lateral: 230 (at 150 km/h)
Rear side: 585 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
66
DXX-790-960/1710-2180-65/65-15i/17.5i-M/M
Model: ADU451503
Dual-band
56
55 70 Unit: mm
67
DXX-790-960/1710-2180-65/65-15i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4517R3
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable 0 - 10 , continuously adjustable
at mid Tilt 14.5 14.7 15.0 16.8 17.3 17.6
Gain (dBi)
over all Tilts 14.5 ±0.5 14.7 ±0.4 14.9 ±0.4 16.8 ±0.5 17.1 ±0.5 17.4 ±0.4
Side lobe suppression for first side
> 18 > 18 > 16 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.1 66 ±1.3 64 ±2.7 65 ±2.1 63 ±1.4 60±3.7
Vertical 3dB beam width (°) 15.7 ±0.8 15.0 ±0.9 14.0 ±1.0 7.5 ±0.4 7.1 ±0.3 6.6 ±0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 24 > 24 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1360 x 259 x 135 106
Packing dimensions (H x W x D) (mm) 1655 x 315 x 195
Antenna weight (kg) 14.3
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 21.1 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 440 (at 150 km/h)
1360
Accessories
68
DXX-790-960/1710-2180-65/65-15i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4517R3
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx……b b
r - Red b - Blue
69
DXX-790-960/1710-2180-65/65-16.5i/18.5i-M/M
Model: ADU451602v01
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable 0 - 8 , continuously adjustable
at mid Tilt 15.7 16.0 16.0 18.5 18.7 18.7
Gain (dBi)
over all Tilts 15.6 ±0.4 15.8 ±0.3 15.9 ±0.3 18.4 ±0.4 18.6 ±0.4 18.5 ±0.5
Side lobe suppression for first side
> 17 > 17 > 17 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.5 66 ±1.5 64 ±1.5 65 ±2.5 63 ±2.5 60±1.5
Vertical 3dB beam width (°) 10.6 ±0.5 10.2 ±0.5 9.5 ±0.5 5.2 ±0.3 5.0 ±0.3 4.7 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 40 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1936 x 259 x 135
Packing dimensions (H x W x D) (mm) 2255 x 305 x 190
Antenna weight (kg) 17.3
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 25.6 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 665 (at 150 km/h)
Wind load (N) Lateral: 345 (at 150 km/h)
Rear side: 880 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
70
DXX-790-960/1710-2180-65/65-16.5i/18.5i-M/M
Model: ADU451602v01
Dual-band
56
55 70
Unit: mm
71
DXX-790-960/1710-2180-65/65-16.5i/18.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4518R3
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable 0 - 8 , continuously adjustable
at mid Tilt 15.7 16.0 16.0 18.5 18.7 18.7
Gain (dBi)
over all Tilts 15.6 ±0.4 15.8 ±0.3 15.9 ±0.3 18.4 ±0.4 18.6 ±0.4 18.5 ±0.5
Side lobe suppression for first side
> 17 > 17 > 17 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.5 66 ±1.5 64 ±1.5 65 ±2.5 63 ±2.5 60±1.5
Vertical 3dB beam width (°) 10.6 ±0.5 10.2 ±0.5 9.5 ±0.5 5.2 ±0.3 5.0 ±0.3 4.7 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 40 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1936 x 259 x 135
Packing dimensions (H x W x D) (mm) 2255 x 305 x 190
Antenna weight (kg) 18.3
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 26.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1936
Accessories
Item Model Description Weight Units per antenna
72
DXX-790-960/1710-2180-65/65-16.5i/18.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4518R3
Properties
RET type Integrated RET
Dual-band
Input voltage range (V) 10 - 30 DC
Adjustment time (full range) (s) < 37 (typically, depending on antenna type)
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
r - Red b - Blue
73
DXX-790-960/1710-2180-65/65-17.5i/18.5i-M/M
Model: ADU451807v01
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable 0 - 8 , continuously adjustable
at mid Tilt 16.7 17.0 17.2 18.4 18.6 18.6
Gain (dBi)
over all Tilts 16.6 ±0.4 16.9 ±0.3 17.0 ±0.3 18.2 ±0.4 18.4 ±0.4 18.3 ±0.5
Side lobe suppression for first side
> 19 > 19 > 19 > 16 > 16 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.5 66 ±1.5 65 ±1.0 64 ±1.5 62 ±1.5 60±2.0
Vertical 3dB beam width (°) 8.4 ±0.5 8.0 ±0.5 7.5 ±0.5 5.2 ±0.3 4.9 ±0.3 4.6 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 40 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 30 > 30 > 30 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 259 x 135
Packing dimensions (H x W x D) (mm) 2815 x 305 x 190
Antenna weight (kg) 21
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 31.2 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 910 (at 150 km/h)
Wind load (N) Lateral: 470 (at 150 km/h)
Rear side: 1200 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
74
DXX-790-960/1710-2180-65/65-17.5i/18.5i-M/M
Model: ADU451807v01
Dual-band
56
55 70
Unit: mm
75
DXX-790-960/1710-2180-65/65-17.5i/18.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4518R0
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable 0 - 8 , continuously adjustable
at mid Tilt 16.7 17.0 17.2 18.4 18.6 18.6
Gain (dBi)
over all Tilts 16.6 ±0.4 16.9 ±0.3 17.0 ±0.3 18.2 ±0.4 18.4 ±0.4 18.3 ±0.5
Side lobe suppression for first side
> 19 > 19 > 19 > 16 > 16 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.5 66 ±1.5 65 ±1.0 64 ±1.5 62 ±1.5 60±2.0
Vertical 3dB beam width (°) 8.4 ±0.5 8.0 ±0.5 7.5 ±0.5 5.2 ±0.3 4.9 ±0.3 4.6 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 40 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 30 > 30 > 30 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 259 x 135
Packing dimensions (H x W x D) (mm) 2815 x 305 x 190
Antenna weight (kg) 22.2
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 32.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
2535
Accessories
Item Model Description Weight Units per antenna
76
DXX-790-960/1710-2180-65/65-17.5i/18.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4518R0
Properties
RET type Integrated RET
Dual-band
Input voltage range (V) 10 - 30 DC
Adjustment time (full range) (s) < 37 (typically, depending on antenna type)
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
r - Red b - Blue
77
DXX-790-960/1710-2180-65/65-15i/17.5i-M/M-C
Model: ADU4517C0
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable 0 - 10 , continuously adjustable
at mid Tilt 14.5 14.7 15.0 16.8 17.3 17.6
Gain (dBi)
over all Tilts 14.5 ±0.5 14.7 ±0.4 14.9 ±0.4 16.8 ±0.5 17.1 ±0.5 17.4 ±0.4
Side lobe suppression for first side
> 18 > 18 > 16 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.1 66 ±1.3 64 ±2.7 65 ±2.1 63 ±1.4 60±3.7
Vertical 3dB beam width (°) 15.7 ±0.8 15.0 ±0.9 14.0 ±1.0 7.5 ±0.4 7.1 ±0.3 6.6 ±0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 24 > 24 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature) 200 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1360 x 259 x 135
Packing dimensions (H x W x D) (mm) 1640 x 305 x 190
Antenna weight (kg) 13.7
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 21.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 440 (at 150 km/h)
Wind load (N) Lateral: 230 (at 150 km/h)
Rear side: 585 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
78
DXX-790-960/1710-2180-65/65-15i/17.5i-M/M-C
Model: ADU4517C0
Accessories
Item Model Description Weight Units per antenna
Dual-band
54
Unit: mm
70 70
C C
79
DXX-790-960/1710-2180-65/65-16.5i/18.5i-M/M-C
Model: ADU4518C1
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable 0 - 8 , continuously adjustable
at mid Tilt 15.7 16.0 16.0 18.5 18.7 18.7
Gain (dBi)
over all Tilts 15.6 ±0.4 15.8 ±0.3 15.9 ±0.3 18.4 ±0.4 18.6 ±0.4 18.5 ±0.5
Side lobe suppression for first side
> 17 > 17 > 17 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.5 66 ±1.5 64 ±1.5 65 ±2.5 63 ±2.5 60±1.5
Vertical 3dB beam width (°) 10.6 ±0.5 10.2 ±0.5 9.5 ±0.5 5.2 ±0.3 5.0 ±0.3 4.7 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 24 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature) 200 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1936 x 259 x 135
Packing dimensions (H x W x D) (mm) 2255 x 305 x 190
Antenna weight (kg) 17.3
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 27.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 665 (at 150 km/h)
Wind load (N) Lateral: 345 (at 150 km/h)
Rear side: 880 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
80
DXX-790-960/1710-2180-65/65-16.5i/18.5i-M/M-C
Model: ADU4518C1
Dual-band
54
70 70 Unit: mm
C C
81
DXX-790-960/1710-2180-65/65-17.5i/18.5i-M/M-C
Model: ADU4518C0
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable 0 - 8 , continuously adjustable
at mid Tilt 16.7 17.0 17.2 18.4 18.6 18.6
Gain (dBi)
over all Tilts 16.6 ±0.4 16.9 ±0.3 17.0 ±0.3 18.2 ±0.4 18.4 ±0.4 18.3 ±0.5
Side lobe suppression for first side
> 19 > 19 > 19 > 16 > 16 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.5 66 ±1.5 65 ±1.0 64 ±1.5 62 ±1.5 60 ±2.0
Vertical 3dB beam width (°) 8.4 ±0.5 8.0 ±0.5 7.5 ±0.5 5.2 ±0.3 4.9 ±0.3 4.6 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 30 > 30 > 30 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature) 200 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 259 x 135
Packing dimensions (H x W x D) (mm) 2815 x 305 x 190
Antenna weight (kg) 20.8
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 30.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 910 (at 150 km/h)
Wind load (N) Lateral: 470 (at 150 km/h)
Rear side: 1200 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 8 ° 2.1 kg 1 (Separate packing)
82
DXX-790-960/1710-2180-65/65-17.5i/18.5i-M/M-C
Model: ADU4518C0
Dual-band
54
70 70
Unit: mm
C C
83
DXX-790-960/1710-2180-65/65-17.5i/18i-M/M
Model: ADU451720
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2180
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 16.7 17.0 17.2 17.7 17.8 18.0
Gain (dBi)
over all Tilts 16.6 ±0.4 16.8 ±0.4 17.0 ±0.4 17.5 ±0.4 17.6 ±0.5 17.8 ±0.5
Side lobe suppression for first side
> 19 > 19 > 19 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±1.0 66 ±1.2 65 ±1.4 64 ±4.3 62 ±3.1 60±2.4
Vertical 3dB beam width (°) 8.4 ±0.4 8.0 ±0.4 7.5 ±0.5 7.0 ±0.4 6.5 ±0.3 6.1 ±0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 40 (790 - 960 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 30 > 30 > 30 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2535 x 259 x 135
Packing dimensions (H x W x D) (mm) 2810 x 300 x 190
Antenna weight (kg) 21.3
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 32.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 910 (at 150 km/h)
Wind load (N) Lateral: 470 (at 150 km/h)
Rear side: 1200 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
84
DXX-790-960/1710-2180-65/65-17.5i/18i-M/M
Model: ADU451720
Dual-band
56
55 70 Unit: mm
85
DXX-790-960/1710-2690-65/65-15i/17.5i-M/M
Model: ADU451716v01
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2690
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 15 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 14.5 14.6 14.7 16.8 17.2 17.4 18.1
Gain (dBi)
over all Tilts 14.5 ± 0.3 14.6 ± 0.4 14.7 ± 0.4 16.7 ± 0.5 17.1 ± 0.5 17.4 ± 0.5 17.9 ± 0.5
Side lobe suppression for first side
> 18 > 18 > 17 > 17 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 4 64 ± 3 62 ± 3 60 ± 5 62 ± 5 60 ± 5 60 ± 5
Vertical 3dB beam width (°) 14.0 ± 0.7 13.3 ± 0.6 12.3 ± 0.7 7.2 ± 0.7 6.5 ± 0.6 5.7 ± 0.5 5.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ± 30° (dB) > 26 > 26 > 25 > 26 > 28 > 28 > 29
Cross polar ratio (dB) 0° > 26 > 23 > 20 > 25 > 26 > 24 > 21
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1499 x 259 x 135
Packing dimensions (H x W x D) (mm) 1850 x 397 x 210
Antenna weight (kg) 16.5
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 25.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 495 (at 150 km/h)
Wind load (N) Lateral: 225 (at 150 km/h)
Rear side: 615 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
86
DXX-790-960/1710-2690-65/65-15i/17.5i-M/M
Model: ADU451716v01
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20D11 Remote electrical tilt module, a couple of AISG connectors 0.6 kg 1 (Separate packing)
Dual-band
72
106
29
1499
1265
Unit: mm
87
DXX-790-960/1710-2690-65/65-15i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R10
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2690
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 15 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 14.5 14.6 14.7 16.8 17.2 17.4 18.1
Gain (dBi)
over all Tilts 14.5 ± 0.3 14.6 ± 0.4 14.7 ± 0.4 16.7 ± 0.5 17.1 ± 0.5 17.4 ± 0.5 17.9 ± 0.5
Side lobe suppression for first side
> 18 > 18 > 17 > 17 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 4 64 ± 3 62 ± 3 60 ± 5 62 ± 5 60 ± 5 60 ± 5
Vertical 3dB beam width (°) 14.0 ± 0.7 13.3 ± 0.6 12.3 ± 0.7 7.2 ± 0.7 6.5 ± 0.6 5.7 ± 0.5 5.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ± 30° (dB) > 26 > 26 > 25 > 26 > 28 > 28 > 29
Cross polar ratio (dB) 0° > 26 > 23 > 20 > 25 > 26 > 24 > 21
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 16 ° 2.1 kg 1 (Separate packing)
88
DXX-790-960/1710-2690-65/65-15i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R10
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
89
DXX-790-960/1710-2690-65/65-16i/18i-M/M
Model: ADU451604v01
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2690
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 15.9 16.0 16.1 17.1 17.5 17.8 18.3
Gain (dBi)
over all Tilts 15.7 ± 0.4 15.8 ± 0.3 16.0 ± 0.3 17.0 ± 0.5 17.4 ± 0.5 17.7 ± 0.3 18.1 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 1.6 64 ± 1.5 63 ± 2.1 63 ± 4.8 61 ± 4.0 60 ± 2.2 60 ± 4.0
Vertical 3dB beam width (°) 9.8 ± 0.4 9.5 ± 0.4 8.9 ± 0.4 7.2 ± 0.5 6.5 ± 0.5 5.6 ± 0.3 5.5 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 25 > 24 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2087 x 259 x 135
Packing dimensions (H x W x D) (mm) 2380 x 315 x 220
Antenna weight (kg) 20.2
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 28.2 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 725 (at 150 km/h)
Wind load (N) Lateral: 330 (at 150 km/h)
Rear side: 900 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
90
DXX-790-960/1710-2690-65/65-16i/18i-M/M
Model: ADU451604v01
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20D11 Remote electrical tilt module, a couple of AISG connectors 0.6 kg 1 (Separate packing)
106
Dual-band
72
29
2087
1255
Unit: mm
91
DXX-790-960/1710-2690-65/65-16i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4518R11
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2690
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 15.9 16.0 16.1 17.1 17.5 17.8 18.3
Gain (dBi)
over all Tilts 15.7 ± 0.4 15.8 ± 0.3 16.0 ± 0.3 17.0 ± 0.5 17.4 ± 0.5 17.7 ± 0.3 18.1 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 1.6 64 ± 1.5 63 ± 2.1 63 ± 4.8 61 ± 4.0 60 ± 2.2 60 ± 4.0
Vertical 3dB beam width (°) 9.8 ± 0.4 9.5 ± 0.4 8.9 ± 0.4 7.2 ± 0.5 6.5 ± 0.5 5.6 ± 0.3 5.5 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 25 > 24 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2087 x 259 x 135
Packing dimensions (H x W x D) (mm) 2380 x 315 x 220
Antenna weight (kg) 20.5
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 28.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
2087
1255
Accessories
92
DXX-790-960/1710-2690-65/65-16i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4518R11
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx……y
y
r - Red y - Yellow
93
DXX-790-960/1710-2690-65/65-17i/18i-M/M
Model: ADU451712v01
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2690
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 16.7 17.1 17.3 17.1 17.5 17.8 18.3
Gain (dBi)
over all Tilts 16.6 ± 0.4 17.0 ± 0.4 17.2 ± 0.4 17.0 ± 0.5 17.4 ± 0.5 17.7 ± 0.3 18.1 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 2.5 64 ± 2.3 63 ± 2.0 63 ± 4.8 61 ± 4.0 60 ± 2.2 60 ± 4.0
Vertical 3dB beam width (°) 8.3 ± 0.4 7.9 ± 0.4 7.3 ± 0.4 7.2 ± 0.5 6.5 ± 0.5 5.6 ± 0.3 5.5 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 26 > 24 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2555 x 259 x 135
Packing dimensions (H x W x D) (mm) 2970 x 315 x 220
Antenna weight (kg) 22.9
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 33.2 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 915 (at 150 km/h)
Wind load (N) Lateral: 415 (at 150 km/h)
Rear side: 1135 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
94
DXX-790-960/1710-2690-65/65-17i/18i-M/M
Model: ADU451712v01
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20D11 Remote electrical tilt module, a couple of AISG connectors 0.6 kg 1 (Separate packing)
106
Dual-band
72
29
2555
1935
Unit: mm
95
DXX-790-960/1710-2690-65/65-17i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4518R12
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2690
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 16.7 17.1 17.3 17.1 17.5 17.8 18.3
Gain (dBi)
over all Tilts 16.6 ± 0.4 17.0 ± 0.4 17.2 ± 0.4 17.0 ± 0.5 17.4 ± 0.5 17.7 ± 0.3 18.1 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 2.5 64 ± 2.3 63 ± 2.0 63 ± 4.8 61 ± 4.0 60 ± 2.2 60 ± 4.0
Vertical 3dB beam width (°) 8.3 ± 0.4 7.9 ± 0.4 7.3 ± 0.4 7.2 ± 0.5 6.5 ± 0.5 5.6 ± 0.3 5.5 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 26 > 24 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0D01 Mechanical downtilt: 0 - 8 ° 2.1 kg 1 (Separate packing)
96
DXX-790-960/1710-2690-65/65-17i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4518R12
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx……y
y
r - Red y - Yellow
97
DXX-690-960/1710-2690-65/65-15i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R9
Antenna Specifications
Electrical Properties
690 - 960 1710 - 2690
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 15 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 14.5 14.5 14.6 14.7 16.8 17.2 17.4 18.1
Gain (dBi) 14.5 14.5 14.6 14.7
over all Tilts 16.7 ± 0.5 17.1 ± 0.5 17.4 ± 0.5 17.9 ± 0.5
± 0.3 ± 0.3 ± 0.4 ± 0.4
Side lobe suppression for first side
> 17 > 18 > 18 > 17 > 17 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 5 66 ± 4 64 ± 3 62 ± 3 60 ± 5 62 ± 5 60 ± 5 60 ± 5
14.0 13.3 12.3
Vertical 3dB beam width (°) 15.3 ± 1 7.2 ± 0.7 6.5 ± 0.6 5.7 ± 0.5 5.3 ± 0.3
± 0.7 ± 0.6 ± 0.7
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
Interband isolation (dB) ≥ 28 (690 - 960 // 1710 - 2690 MHz)
Front to back ratio , ± 30° (dB) > 25 > 26 > 26 > 25 > 26 > 28 > 28 > 29
Cross polar ratio (dB) 0° > 20 > 26 > 23 > 20 > 25 > 26 > 24 > 21
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
98
DXX-690-960/1710-2690-65/65-15i/17.5i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R9
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx……..r
HWMxxx….....y
y
r - Red y - Yellow
99
DXX-690-960/1710-2690-65/65-16i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4518R7
Antenna Specifications
Electrical Properties
690 - 960 1710 - 2690
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 15.5 15.9 16.0 16.1 17.1 17.5 17.8 18.3
Gain (dBi)
over all Tilts 15.5 ± 0.4 15.7 ± 0.4 15.8 ± 0.3 16.0 ± 0.3 17.0 ± 0.5 17.4 ± 0.5 17.7 ± 0.3 18.1 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 18 > 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 2.4 66 ± 1.6 64 ± 1.5 63 ± 2.1 63 ± 4.8 61 ± 4.0 60± 2.2 60 ± 4.0
Vertical 3dB beam width (°) 10.5 ± 0.5 9.8 ± 0.4 9.5 ± 0.4 8.9 ± 0.4 7.2 ± 0.5 6.5 ± 0.5 5.6 ± 0.3 5.5 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (690 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 24 > 25 > 25 > 25 > 24 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2087 x 259 x 135
Packing dimensions (H x W x D) (mm) 2380 x 315 x 220
Antenna weight (kg) 20.5
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 28.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
2087
1255
Accessories
100
DXX-690-960/1710-2690-65/65-16i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.0m
Model: ADU4518R7
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx……y y
r - Red y - Yellow
101
DXX-690-960/1710-2690-65/65-17i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4518R8
Antenna Specifications
Electrical Properties
690 - 960 1710 - 2690
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable 2 - 12 , continuously adjustable
at mid Tilt 16.6 16.7 17.1 17.3 17.1 17.5 17.8 18.3
Gain (dBi)
over all Tilts 16.5 ± 0.3 16.6 ± 0.4 17.0 ± 0.4 17.2 ± 0.4 17.0 ± 0.5 17.4 ± 0.5 17.7 ± 0.3 18.1 ± 0.4
Side lobe suppression for first side
> 17 > 18 > 18 > 18 > 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ± 2.5 66 ± 2.5 64 ± 2.3 63 ± 2.0 63 ± 4.8 61 ± 4.0 60 ± 2.2 60 ± 4.0
Vertical 3dB beam width (°) 8.9 ± 0.5 8.3 ± 0.4 7.9 ± 0.4 7.3 ± 0.4 7.2 ± 0.5 6.5 ± 0.5 5.6 ± 0.3 5.5 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (690 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 24 > 25 > 25 > 26 > 24 > 25 > 25 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
106
Mechanical Properties
Accessories
Item Model Description Weight Units per antenna
102
DXX-690-960/1710-2690-65/65-17i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 2.6m
Model: ADU4518R8
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx……y
y
r - Red y - Yellow
103
DXX-1710-2200/1710-2200-65/65-18i/18i-M/M
Model: ADU451819v01
Antenna Specifications
Electrical Properties
2 x (1710 - 2200)
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 17.6 18.0 18.2 18.1
Gain (dBi)
over all Tilts 17.5 ± 0.5 17.8 ± 0.4 18.0 ± 0.4 17.9 ± 0.4
Side lobe suppression for first side
> 20 > 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ± 3 66 ± 3 64 ± 5 61 ± 4
Vertical 3dB beam width (°) 7.4 ± 0.4 6.9 ± 0.4 6.5 ± 0.6 6.0 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30 (1710 - 2200 // 1710 - 2200 MHz)
Front to back ratio, ±30°(dB) > 27 > 27 > 26 > 26
Cross polar ratio (dB) 0° > 22 > 22 > 21 > 18
Max. power per input (W) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 269 x 86
Packing dimensions (H x W x D) (mm) 1680 x 340 x 155
Antenna weight (kg) 10.6
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 17.6 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 540 (at 150 km/h)
Wind load (N) Lateral: 75 (at 150 km/h)
Rear side: 510 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
104
DXX-1710-2200/1710-2200-65/65-18i/18i-M/M
Model: ADU451819v01
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20D11 Remote electrical tilt module, a couple of AISG connectors 0.6 kg 1 (Separate packing)
Dual-band
60 106
35.5
1365
1274
Unit: mm
105
DXX-1710-2200/1710-2200-65/65-18i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R1v01
Antenna Specifications
Electrical Properties
2 x (1710 - 2200)
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 17.6 18.0 18.2 18.1
Gain (dBi)
over all Tilts 17.5 ± 0.5 17.8 ± 0.4 18.0 ± 0.4 17.9 ±0.4
Side lobe suppression for first side
> 20 > 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ± 3 66 ± 3 64 ± 5 61 ± 4
Vertical 3dB beam width (°) 7.4 ± 0.4 6.9 ± 0.4 6.5 ± 0.6 6.0 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30 (1710 - 2200 // 1710 - 2200 MHz)
Front to back ratio, ±30°(dB) > 27 > 27 > 26 > 26
Cross polar ratio (dB) 0° > 22 > 22 > 21 > 18
Max. power per input (W) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 269 x 86 106
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0B01 Mechanical downtilt: 0 - 16 ° 1.3 kg 1 (Separate packing)
106
DXX-1710-2200/1710-2200-65/65-18i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R1v01
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx……..bL
HWMxxx…...bbR bL bbR
107
DXX-1710-2200/1710-2200-65/65-19.5i/19.5i-M/M
Model: ADU451902
Antenna Specifications
Electrical Properties
2 x (1710 - 2200)
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 6 , continuously adjustable , each band separately
at mid Tilt 18.7 19.1 19.4 19.3
Gain (dBi)
over all Tilts 18.6 ± 0.4 18.9 ± 0.4 19.1 ± 0.3 19.1 ± 0.4
Side lobe suppression for first side
> 17 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ± 2.8 65 ± 2.8 62 ± 4.0 60 ± 4.0
Vertical 3dB beam width (°) 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.3 4.1 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30
Front to back ratio, ±30° (dB) > 27 > 27 > 27 > 26
Cross polar ratio (dB) 0° > 25 > 25 > 25 > 25
Max. power per input (W) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1954 x 323 x 89
Packing dimensions (H x W x D) (mm) 2235 x 365 x 145
Antenna weight (kg) 17.3
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 23.8 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 890 (at 150 km/h)
Wind load (N) Lateral: 170 (at 150 km/h)
Rear side: 1000 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
108
DXX-1710-2200/1710-2200-65/65-19.5i/19.5i-M/M
Model: ADU451902
43 36 59
Dual-band
31
+45° +45°
-45° -45°
109
DXX-1710-2170/2490-2690-65/65-18i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R5
Antenna Specifications
Electrical Properties
1710 - 2170
Frequency range (MHz) 2490 - 2690
1710 - 1990 1920 - 2170
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 17.5 17.7 18.3
Gain (dBi)
over all Tilts 17.3 ± 0.4 17.5 ± 0.4 18.1 ± 0.5
Side lobe suppression for first side
> 17 > 16 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ± 3.1 63 ± 3.5 60 ± 4.5
Vertical 3dB beam width (°) 6.4 ± 0.5 5.9 ± 0.4 4.6 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30 (1710 - 2170 // 2490 - 2690 MHz)
Front to back ratio, ±30° (dB) > 24 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
68
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1490 x 155 x 109
Packing dimensions (H x W x D) (mm) 1818 x 210 x 180
Antenna net weight (kg) 9.8
Clamps weight (kg) 2.0 (2 units)
Antenna packing weight (kg) 15.3 (Included clamps)
Mast diameter supported (mm) 38 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
1512
1544
Accessories
110
DXX-1710-2170/2490-2690-65/65-18i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R5
Dual-band
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx.…..b
HWMxxx…...y
b y
b - Blue y - Yellow
111
DXX-1710-2690/1710-2690-65/65-16i/16i-M/M
Model: ADU451507
Antenna Specifications
Electrical Properties
2 x (1710 - 2690)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable, each band separately
at mid Tilt 15.2 15.9 16.0 16.5
Gain (dBi)
over all Tilts 15.2 ± 0.5 15.8 ± 0.5 16.0 ± 0.5 16.3 ± 0.5
Side lobe suppression for first side
> 18 > 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 5.2 64 ± 4.8 62 ± 4.1 60 ± 4.4
Vertical 3dB beam width (°) 12.0 ± 0.9 10.8 ± 0.9 10.0 ± 0.9 8.6 ± 0.6
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 24 > 24 > 24 > 24
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 840 x 299 x 109
Packing dimensions (H x W x D) (mm) 1200 x 350 x 195
Antenna weight (kg) 9.9
Clamps weight (kg) 2.0 (2 units)
Antenna packing weight (kg) 16.2 (Included clamps)
Mast diameter supported (mm) 38 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 290 (at 150 km/h)
Wind load (N) Lateral: 60 (at 150 km/h)
Rear side: 340 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0A01 Mechanical downtilt: 0° - 20° 0.6 kg 1 (Separate packing)
112
DXX-1710-2690/1710-2690-65/65-16i/16i-M/M
Model: ADU451507
68
Dual-band
55 58
83 58
Unit: mm
840
748
1710 - 2690 1710 - 2690
X X
+45° +45°
-45° -45°
113
DXX-1710-2690/1710-2690-65/65-18i/18i-M/M
Model: ADU451816v02
Antenna Specifications
Electrical Properties
2 x (1710 - 2690)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 17.4 17.9 18.2 18.4
Gain (dBi)
over all Tilts 17.3 ±0.3 17.7 ±0.4 18.0 ±0.3 18.2 ±0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ±2.7 65 ±2.7 63 ±2.8 61 ±2.6
Vertical 3dB beam width (°) 6.9 ±0.3 6.3 ±0.3 5.5 ±0.3 5.0 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 27 > 27 > 27 > 27
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 269 x 86
Packing dimensions (H x W x D) (mm) 1680 x 340 x 155
Antenna weight (kg) 11.8
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 18.8 (included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 540 (at 150 km/h)
Wind load (N) Lateral: 75 (at 150 km/h)
Rear side: 510 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 4 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
114
DXX-1710-2690/1710-2690-65/65-18i/18i-M/M
Model: ADU451816v02
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20D11 Remote electrical tilt module, a couple of AISG connectors 0.6 kg 1 (Separate packing)
Dual-band
106
60
35.5
1274
1365
Unit: mm
115
DXX-1710-2690/1710-2690-65/65-18i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R6v01
Antenna Specifications
Electrical Properties
2 x (1710 - 2690)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 17.4 17.9 18.2 18.4
Gain (dBi)
over all Tilts 17.3 ± 0.3 17.7 ± 0.4 18.0 ± 0.3 18.2 ± 0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 2.7 65 ± 2.7 63 ± 2.8 61 ± 2.6
Vertical 3dB beam width (°) 6.9 ± 0.3 6.3 ± 0.3 5.5 ± 0.3 5.0 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 27 > 27 > 27 > 27
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 269 x 86 106
Accessories
Item Model Description Weight Units per antenna
116
DXX-1710-2690/1710-2690-65/65-18i/18i-M/M-R
EasyRET Dual-Band Antenna with 2 Integrated RCUs - 1.4m
Model: ADU4518R6v01
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
Dual-band
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx……..yL
HWMxxx……yyR
yL yyR
y - Yellow
L - Left array R - Right array
117
B - 3. Tri-band Antenna
790-862/
0-10/
880-960/ 65/65/65 15.5/16/18
0-10/0-10
EasyRET2.0 6 x 7/16 DIN-F 2020 x 298 x 150 ATR4518R2 121 K
1710-2690
790-862/
Tri-band
0-10/
880-960/ 65/65/65 16.5/17/18
0-10/0-10
EasyRET2.0 6 x 7/16 DIN-F 2520 x 298 x 150 ATR4518R12 123 K
1710-2690
690-862/
0-12/
880-960/ 65/65/65 14/14.5/17.5
0-12/2-12
EasyRET2.0 6 x 7/16 DIN-F 1490 x 298 x 150 ATR4517R5 125 K
1710-2690
790-960/
16.5/ 0-12/
1710-2180/ 65/65/65
16.5/16.5 0-12/0-12
MET1.0 6 x 7/16 DIN-F 2098 x 259 x 135 ATR451602v01 127 L
1710-2180
790-960/
16.5/ 0-12/
1710-2180/ 65/65/65
16.5/16.5 0-12/0-12
EasyRET1.0 6 x 7/16 DIN-F 2098 x 259 x 135 ATR4516R0 129 L
1710-2180
790-960/
0-14/
1710-2180/ 65/65/65 15/17.5/17.5
0-10/0-10
MET1.0 6 x 7/16 DIN-F 1497 x 349 x 166 ATR451715 131 M
1710-2180
790-960/
0-14/
1710-2180/ 65/65/65 15/17.5/17.5
0-10/0-10
EasyRET2.0 6 x 7/16 DIN-F 1497 x 349 x 166 ATR4517R3 133 M
1710-2180
790-960/
17.5/ 0-10/
1710-2180/ 65/65/65
17.5/17.5 0-10/0-10
MET1.0 6 x 7/16 DIN-F 2680 x 259 x 135 ATR451704v01 135 L
1710-2180
790-960/
17.5/ 0-10/
1710-2180/ 65/65/65
17.5/17.5 0-10/0-10
EasyRET1.0 6 x 7/16 DIN-F 2680 x 259 x 135 ATR4517R0 137 L
1710-2180
790-960/
15/ 0-14/
1710-2690/ 65/65/65
17.5/17.5 0-10/0-10
EasyRET1.0 6 x 7/16 DIN-F 1499 x 349 x 166 ATR4517R1 139 N
1710-2690
790-960/
0-10/
1710-2690/ 65/65/65 16/18/18
0-10/0-10
EasyRET1.0 6 x 7/16 DIN-F 1999 x 349 x 166 ATR4518R4 141 N
1710-2690
790-960/
0-10/
1710-2690/ 65/65/65 17/18/18
0-10/0-10
EasyRET1.0 6 x 7/16 DIN-F 2528 x 349 x 166 ATR4518R7 143 N
1710-2690
790-960/
0-14/
1710-2690/ 65/65/65 15/17.5/17.5
0-10/0-10
MET1.0 6 x 7/16 DIN-F 1536 x 349 x 166 ATR451709 145 N
1710-2690
790-960/
0-10/
1710-2690/ 65/65/65 16/18/18
0-10/0-10
MET1.0 6 x 7/16 DIN-F 1999 x 349 x 166 ATR451606 147 N
1710-2690
790-960/
0-10/
1710-2690/ 65/65/65 17/18/18
0-10/0-10
MET1.0 6 x 7/16 DIN-F 2528 x 349 x 166 ATR451607 149 N
1710-2690
** Preliminary Issue
B - 3. Tri-band Antenna
690-960/
0-14/
1710-2690/ 65/65/65 15/17.5/17.5
0-10/0-10
MET2.0 6 x 7/16 DIN-F 1499 x 359 x 178 ATR451806 151 N
1710-2690
690-960/
0-14/
1710-2690/ 65/65/65 15/17.5/17.5
0-10/0-10
EasyRET2.0 6 x 7/16 DIN-F 1499 x 359 x 178 ATR4518R13 153 N
1710-2690
690-960/
0-10/
1710-2690/ 65/65/65 16/18/18
0-10/0-10
EasyRET2.0 6 x 7/16 DIN-F 2022 x 359 x 178 ATR4518R6 155 N
1710-2690
690-960/
0-10/
1710-2690/ 65/65/65 17/18/18
0-10/0-10
EasyRET2.0 6 x 7/16 DIN-F 2523 x 359 x 178 ATR4518R11 157 N
1710-2690
1710-2200/
0-10/
1710-2200/ 65/65/65 18/18/18
0-10/0-10
MET2.0 6 x 7/16 DIN-F 1365 x 376 x 99 ATR451807 159 O
1710-2200
1710-2200/
0-10/
1710-2200/ 65/65/65 18/18/18
0-10/0-10
EasyRET2.0 6 x 7/16 DIN-F 1365 x 376 x 99 ATR4518R15 161 O
1710-2200
1710-2690/
0-12/
1710-2170/ 65/65/65 18/18/18
0-12/0-12
EasyRET1.0 6 x 7/16 DIN-F 1445 x 299 x 109 ATR4518R3 163 Q
2490-2690
1710-2690/
0-12/
1710-2690/ 65/65/65 18/18/18
0-12/0-12
MET2.0 6 x 7/16 DIN-F 1365 x 376 x 99 ATR451714v01 165 P
1710-2690
1710-2690/
0-12/
1710-2690/ 65/65/65 18/18/18
0-12/0-12
EasyRET2.0 6 x 7/16 DIN-F 1365 x 376 x 99 ATR4518R14 167 P
1710-2690
** Preliminary Issue
bT
bbB
r rr r r r
DXXX-790-862/880-960/1710-2690-65/65/65-15.5i/16i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4518R2
Antenna Specifications
Electrical Properties
1710 - 2690
Frequency range (MHz) 790 - 862 880 - 960
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 15.0 15.4 17.8 18.0 18.0 18.0
Gain (dBi)
over all Tilts 15.0 ±0.4 15.3 ±0.3 17.5 ±0.5 17.9 ±0.3 17.9 ±0.4 17.8 ±0.5
Side lobe suppression for first side lobe above main
> 16 > 16 > 16 > 17 > 17 > 16
Tri-band
beam (dB)
Horizontal 3dB beam width (°) 68 ±2.0 65 ±2.0 61 ±3.0 60 ±3.0 60 ±5.0 61 ±5.0
Vertical 3dB beam width (°) 10.1 ±0.8 9.9 ±0.8 6.0 ±0.4 5.4 ±0.4 4.6 ±0.3 4.3 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 28 (790 - 862 // 880 - 960 MHz)
Interband isolation (dB)
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 26 > 26 > 27 > 27 > 26 > 26
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18
500 (at 50℃ ambient
Max. power per input (W) 250 (at 50℃ ambient temperature)
temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
121
DXXX-790-862/880-960/1710-2690-65/65/65-15.5i/16i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4518R2
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC in/out DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx….r
HWMxxx…rr
y
HWMxxx….y
r - Red y - Yellow
r rr
122
DXXX-790-862/880-960/1710-2690-65/65/65-16.5i/17i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4518R12
Antenna Specifications
Electrical Properties
1710 - 2690
Frequency range (MHz) 790 - 862 880 - 960
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 15.9 16.3 17.8 18.0 18.0 18.0
Gain (dBi)
over all Tilts 15.8 ± 0.4 16.1 ± 0.5 17.5 ± 0.5 17.8 ± 0.4 17.8 ± 0.4 17.8 ± 0.4
Side lobe suppression for first side
> 16 > 16 > 16 > 17 > 17 > 16
Tri-band
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ± 2.0 64 ± 2.0 61 ± 4.0 60 ± 4.0 60 ± 4.0 61 ± 5.0
Vertical 3dB beam width (°) 8.5 ± 0.7 7.5 ± 0.7 6.0 ± 0.5 5.4 ± 0.4 4.6 ± 0.3 4.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
≥ 28 (790 - 862 // 880 - 960 MHz)
Interband isolation (dB)
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 28 > 28 > 28 > 28 > 28 > 28
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18
500 (at 50℃ ambient
Max. power per input (W) 250 (at 50℃ ambient temperature)
temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2520 x 298 x 150
Packing dimensions (H x W x D) (mm) 2885 x 365 x 235
Antenna weight (kg) 29.5
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 44.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1913
2520
Accessories
Item Model Description Weight Units per antenna
123
DXXX-790-862/880-960/1710-2690-65/65/65-16.5i/17i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4518R12
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC in/out DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
r - Red y - Yellow
r rr
124
DXXX-690-862/880-960/1710-2690-65/65/65-14i/14.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4517R5
Antenna Specifications
Electrical Properties
690 - 862 880 - 960 1710 - 2690
Frequency range (MHz)
690 - 820 790 - 862 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
0 - 12 , continuously adjustable , each band
Electrical downtilt (°) 2 - 12 , continuously adjustable
separately
at mid Tilt 13.8 13.8 14.3 16.8 17.0 17.2 17.5
Gain (dBi)
over all Tilts 13.7 ±0.3 13.7 ±0.3 14.1 ±0.5 16.6 ±0.4 16.8 ±0.4 17.1 ±0.4 17.4 ±0.4
Tri-band
Side lobe suppression for first side
> 16 > 16 > 17 > 15 > 15 > 15 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±2.0 66 ±2.0 63 ±2.0 63 ±5.0 61 ±5.0 60 ±5.0 60 ±5.0
Vertical 3dB beam width (°) 15.3 ±1.0 13.5 ±1.0 12.0 ±1.0 6.5 ±0.5 6.0 ±0.5 5.2 ±0.3 4.8 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
≥ 28 (690 - 862 // 880 - 960 MHz)
Interband isolation (dB) ≥ 28 (690 - 862 // 1710 - 2690 MHz)
≥ 28 (880 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 28 > 28 > 26 > 27 > 27 > 27 > 28
Cross polar ratio (dB) 0° > 25 > 22 > 18 > 17 > 17 > 20 > 19
Max. power per input (W) 300 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Accessories
Item Model Description Weight Units per antenna
125
DXXX-690-862/880-960/1710-2690-65/65/65-14i/14.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4517R5
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx……y
HWMxxx……rr y
r - Red y - Yellow
r rr
126
DXXX-790-960/1710-2180/1710-2180-65/65/65-16.5i/16.5i/16.5i-
M/M/M
Model: ATR451602v01
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2180)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable , each band separately
at mid Tilt 16.0 16.3 16.2
over all Tilts 15.9 ±0.5 16.0 ±0.4 16.1 ±0.4
at mid Tilt 16.2 16.4 16.5
Gain (dBi) Bottom
over all Tilts 16.0 ±0.4 16.2 ±0.4 16.3 ±0.4
Tri-band
at mid Tilt 16.0 16.4 16.5
Top
over all Tilts 15.8 ±0.4 16.2 ±0.4 16.3 ±0.4
Side lobe suppression for first side
> 18 > 19 > 19 > 17 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±2.0 66 ±2.0 65 ±3.0 64 ±4.0 60 ±5.0 60 ±5.0
Bottom: 9.6 Bottom: 8.9 Bottom: 8.3
±0.6 ±0.5 ±0.6
Vertical 3dB beam width (°) 10.7 ±0.5 10.1 ±0.5 9.4 ±0.5
Top: 8.5 ±0.6 Top: 8.0 ±0.5 Top: 7.5 ±0.6
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2098 x 259 x 135
Packing dimensions (H x W x D) (mm) 2380 x 305 x 190
Antenna weight (kg) 19.4
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 28.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 730 (at 150 km/h)
Wind load (N) Lateral: 380 (at 150 km/h)
Rear side: 965 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 6 x 7/16 DIN Female
Connector position Bottom
127
DXXX-790-960/1710-2180/1710-2180-65/65/65-16.5i/16.5i/16.5i-
M/M/M
Model: ATR451602v01
Accessories
61 44
17
56
55 70
T - Top Column B - Bottom Column Unit: mm
1710 - 2180
Bottom
790 - 960 X 1710 - 2180
X Top
+45° -45° X
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
128
DXXX-790-960/1710-2180/1710-2180-65/65/65-16.5i/16.5i/16.5i-
M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4516R0
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2180)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable , each band separately
at mid Tilt 16.0 16.3 16.2
over all Tilts 15.9 ±0.5 16.0 ±0.4 16.1 ±0.4
at mid Tilt 16.2 16.4 16.5
Gain (dBi) Bottom
Tri-band
over all Tilts 16.0 ±0.4 16.2 ±0.4 16.3 ±0.4
at mid Tilt 16.0 16.4 16.5
Top
over all Tilts 15.8 ±0.4 16.2 ±0.4 16.3 ±0.4
Side lobe suppression for first side
> 18 > 19 > 19 > 17 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±2.0 66 ±2.0 65 ±3.0 64 ±4.0 60 ±5.0 60 ±5.0
Bottom: 9.6 Bottom: 8.9 Bottom: 8.3
±0.6 ±0.5 ±0.6
Vertical 3dB beam width (°) 10.7 ±0.5 10.1 ±0.5 9.4 ±0.5
Top: 8.5 Top: 8.0 Top: 7.5
±0.6 ±0.5 ±0.6
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
≥ 40 (790 - 960 // 1710 - 2180 MHz)
Interband isolation (dB)
≥ 35 (1710 - 2180 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 25 > 25 > 25 > 25 > 24
Cross polar ratio (dB) 0° > 26 > 26 > 26 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2098 x 259 x 135
Packing dimensions (H x W x D) (mm) 2380 x 305 x 190
Antenna weight (kg) 20.7
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 29.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
2098
129
DXXX-790-960/1710-2180/1710-2180-65/65/65-16.5i/16.5i/16.5i-
M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4516R0
Accessories
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (s) < 37 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx…….r
bT
HWMxxx…..bT
HWMxxx…bbB
bbB
r - Red b - Blue
T - Top array B - Bottom array
r
130
DXXX-790-960/1710-2180/1710-2180-65/65/65-15i/17.5i/17.5i-M/M/M
Model: ATR451715
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2180)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
0 - 10 , continuously adjustable
Electrical downtilt (°) 0 - 14 , continuously adjustable
each band separately
at mid Tilt 14.5 15.0 15.0 17.1 17.3 17.4
Gain (dBi)
over all Tilts 14.5 ±0.5 14.8 ±0.4 15.1 ±0.5 16.9 ±0.4 17.2 ±0.4 17.2 ±0.4
Tri-band
Side lobe suppression for first side
> 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ±3.0 64 ±3.0 62 ±3.0 66 ±4.0 64 ±4.0 63±4.0
Vertical 3dB beam width (°) 15.2 ±0.8 14.8 ±0.8 13.7 ±0.8 7.2 ±0.5 7.0 ±0.3 6.6 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
≥ 30 (790 - 960 // 1710 - 2180 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2180 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 24 > 25 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1497 x 349 x 166
Packing dimensions (H x W x D) (mm) 1825 x 410 x 235
Antenna weight (kg) 19.5
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 29.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 505 (at 150 km/h)
Wind load (N) Lateral: 165 (at 150 km/h)
Rear side: 540 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 6 x 7/16 DIN Female
Connector position Bottom
131
DXXX-790-960/1710-2180/1710-2180-65/65/65-15i/17.5i/17.5i-M/M/M
Model: ATR451715
Accessories
106
57 57 60
63
Unit: mm
1395
1497
790 - 960
1710 - 2180 X 1710 - 2180
Left Right
X X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
132
DXXX-790-960/1710-2180/1710-2180-65/65/65-15i/17.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.5m
Model: ATR4517R3
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2180)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
0 - 10 , continuously adjustable , each band
Electrical downtilt (°) 0 - 14 , continuously adjustable
separately
at mid Tilt 14.5 15.0 15.0 17.1 17.3 17.4
Gain (dBi)
over all Tilts 14.5 ±0.5 14.8 ±0.4 15.1 ±0.5 16.9 ±0.4 17.2 ±0.4 17.2 ±0.4
Tri-band
Side lobe suppression for first side
> 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ±3.0 64 ±3.0 62 ±3.0 66 ±4.0 64 ±4.0 63±4.0
Vertical 3dB beam width (°) 15.2 ±0.8 14.8 ±0.8 13.7 ±0.8 7.2 ±0.5 7.0 ±0.3 6.6 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
≥ 30 (790 - 960 // 1710 - 2180 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2180 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 24 > 25 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1497 x 349 x 166
Packing dimensions (H x W x D) (mm) 1825 x 415 x 240
Antenna weight (kg) 20.2
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 29.4 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1497
Accessories
Item Model Description Weight Units per antenna
133
DXXX-790-960/1710-2180/1710-2180-65/65/65-15i/17.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.5m
Model: ATR4517R3
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
r - Red b - Blue
L - Left array R - Right array
r
134
DXXX-790-960/1710-2180/1710-2180-65/65/65-17.5i/17.5i/17.5i-
M/M/M
Model: ATR451704v01
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2180)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 16.8 17.1 17.3
over all Tilts 16.7 ±0.4 16.9 ±0.4 17.1 ±0.4
at mid Tilt 17.1 17.6 17.6
Gain (dBi) Bottom
over all Tilts 16.9 ±0.4 17.4 ±0.4 17.4 ±0.4
Tri-band
at mid Tilt 17.1 17.3 17.3
Top
over all Tilts 16.8 ±0.4 17.1 ±0.4 17.0 ±0.5
Side lobe suppression for first side
> 19 > 19 > 19 > 18 > 16 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±2.0 66 ±2.0 65 ±3.0 63 ±4.0 62 ±3.0 60 ±4.0
Bottom: 7.5 Bottom: 7.0 Bottom: 6.6
Vertical 3dB beam width (°) 8.4 ±0.4 8.0 ±0.4 7.5 ±0.4 ±0.3 ±0.3 ±0.4
Top: 7.0 ±0.3 Top: 6.5 ±0.3 Top: 6.1 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
≥ 40 (790 - 960 // 1710 - 2180 MHz)
Interband isolation (dB)
≥ 40 (1710 - 2180 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 26 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 28 > 28 > 28 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2680 x 259 x 135
Packing dimensions (H x W x D) (mm) 2965 x 305 x 190
Antenna weight (kg) 23
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 32.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 970 (at 150 km/h)
Wind load (N) Lateral: 500 (at 150 km/h)
Rear side: 1285 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 6 x 7/16 DIN Female
Connector position Bottom
135
DXXX-790-960/1710-2180/1710-2180-65/65/65-17.5i/17.5i/17.5i-
M/M/M
Model: ATR451704v01
Accessories
61 44
17
56
55 70
T - Top Column B - Bottom Column
Unit: mm
1710 - 2180
Bottom
790 - 960 X 1710 - 2180
X Top
X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
136
DXXX-790-960/1710-2180/1710-2180-65/65/65-17.5i/17.5i/17.5i-
M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4517R0
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2180)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 16.8 17.1 17.3
over all Tilts 16.7 ±0.4 16.9 ±0.4 17.1 ±0.4
at mid Tilt 17.1 17.6 17.6
Gain (dBi) Bottom
over all Tilts 16.9 ±0.4 17.4 ±0.4 17.4 ±0.4
Tri-band
at mid Tilt 17.1 17.3 17.3
Top
over all Tilts 16.8 ±0.4 17.1 ±0.4 17.0 ±0.5
Side lobe suppression for first side
> 19 > 19 > 19 > 18 > 16 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 69 ±2.0 66 ±2.0 65 ±3.0 63 ±4.0 62 ±3.0 60 ±4.0
Bottom: 7.5 Bottom: 7.0 Bottom: 6.6
Vertical 3dB beam width (°) 8.4 ±0.4 8.0 ±0.4 7.5 ±0.4 ±0.3 ±0.3 ±0.4
Top: 7.0 ±0.3 Top: 6.5 ±0.3 Top: 6.1 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
≥ 40 (790 - 960 // 1710 - 2180 MHz)
Interband isolation (dB)
≥ 40 (1710 - 2180 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 26 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 28 > 28 > 28 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2680 x 259 x 135
Packing dimensions (H x W x D) (mm) 2965 x 305 x 190
Antenna weight (kg) 25.0
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 33.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
2680
137
DXXX-790-960/1710-2180/1710-2180-65/65/65-17.5i/17.5i/17.5i-
M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4517R0
Accessories
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (s) < 37 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx…….r bT
HWMxxx…..bT
HWMxxx…bbB
bbB
r - Red b - Blue
T - Top array B - Bottom array r
138
DXXX-790-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4517R1
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2690)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable 0 - 10 , continuously adjustable , each band separately
at mid Tilt 14.3 14.5 14.7 17.3 17.8 18.0 17.9
Gain (dBi)
over all Tilts 14.2 ± 0.4 14.4 ± 0.4 14.6 ± 0.5 17.2 ± 0.5 17.6 ± 0.4 17.8 ± 0.4 17.8 ± 0.5
Side lobe suppression for first side
> 17 > 16 > 16 > 16 > 16 > 16 > 15
Tri-band
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 3.4 64 ± 3.7 62 ± 4.8 63 ± 5.0 62 ± 5.0 60 ± 4.3 60 ± 5.0
Vertical 3dB beam width (°) 16.0 ± 0.9 15.6 ± 0.9 14.6 ± 1.0 6.4 ± 0.4 5.7 ± 0.4 5.1 ± 0.3 4.6 ± 0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 24 > 24 > 24 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
139
DXXX-790-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4517R1
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx..….r
HWMxxx….yL
yL yyR
HWMxxx..yyR
r - Red y - Yellow
L - Left array R - Right array
r
140
DXXX-790-960/1710-2690/1710-2690-65/65/65-16i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4518R4
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2690)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 15.9 16.1 16.3 17.5 17.8 18.0 18.2
Gain (dBi)
over all Tilts 15.8 ± 0.4 16.0 ± 0.4 16.2 ± 0.5 17.4 ± 0.4 17.6 ± 0.5 17.9 ± 0.5 18.0 ± 0.5
Side lobe suppression for first side
> 17 > 17 > 17 > 16 > 16 > 16 > 16
Tri-band
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 1.5 64 ± 3.0 62 ± 4.1 65 ± 4.8 62 ± 3.7 60 ± 4.3 60 ± 4.5
Vertical 3dB beam width (°) 10.1 ± 0.4 9.8 ± 0.5 9.3 ± 0.5 5.8 ± 0.3 5.4 ± 0.3 4.8 ± 0.3 4.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1999 x 349 x 166
Packing dimensions (H x W x D) (mm) 2350 x 415 x 240
Antenna weight (kg) 25
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 39.8 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1999
Accessories
Item Model Description Weight Units per antenna
141
DXXX-790-960/1710-2690/1710-2690-65/65/65-16i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4518R4
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx..….r
HWMxxx….yL
yL yyR
HWMxxx..yyR
r - Red y - Yellow
L - Left array R - Right array
r
142
DXXX-790-960/1710-2690/1710-2690-65/65/65-17i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4518R7
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2690)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 16.8 17.0 17.3 17.5 17.8 18.0 18.2
Gain (dBi)
over all Tilts 16.7 ± 0.4 17.0 ± 0.3 17.2 ± 0.5 17.4 ± 0.5 17.6 ± 0.5 17.9 ± 0.5 18.0 ± 0.5
Side lobe suppression for first side
> 17 > 17 > 17 > 16 > 16 > 16 > 16
Tri-band
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 2.0 64 ± 2.0 62 ± 4.1 65 ± 4.8 62 ± 3.7 60 ± 4.3 60 ± 4.5
Vertical 3dB beam width (°) 8.6 ± 0.5 8.2 ± 0.5 7.6 ± 0.5 5.8 ± 0.3 5.4 ± 0.3 4.8 ± 0.3 4.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2528 x 349 x 166
Packing dimensions (H x W x D) (mm) 2885 x 420 x 240
Antenna weight (kg) 29.5
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 44.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
2528
Accessories
Item Model Description Weight Units per antenna
143
DXXX-790-960/1710-2690/1710-2690-65/65/65-17i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4518R7
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx..yyR
r - Red y - Yellow
L - Left array R - Right array r
144
DXXX-790-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M
Model: ATR451709
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2690)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable 0 - 10 , continuously adjustable , each band separately
at mid Tilt 14.3 14.5 14.7 17.3 17.8 18.0 17.9
Gain (dBi)
over all Tilts 14.2 ± 0.4 14.4 ± 0.4 14.6 ± 0.5 17.2 ± 0.5 17.6 ± 0.4 17.8 ± 0.4 17.8 ± 0.5
Side lobe suppression for first side
Tri-band
> 17 > 16 > 16 > 16 > 16 > 16 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 3.4 64 ± 3.7 62 ± 4.8 63 ± 5.0 62 ± 5.0 60 ± 4.3 60 ± 5.0
Vertical 3dB beam width (°) 14.2 ± 0.9 13.8 ± 0.9 13.0 ± 1.0 6.4 ± 0.4 5.7 ± 0.4 5.1 ± 0.3 4.6 ± 0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 24 > 24 > 24 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1536 x 349 x 166
Packing dimensions (H x W x D) (mm) 1870 x 415 x 240
145
DXXX-790-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M
Model: ATR451709
Accessories
Item Model Description Weight Units per antenna
57 57 60
63
Unit: mm
790 - 960
1710 - 2690 X 1710 - 2690
Left Right
X X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
146
DXXX-790-960/1710-2690/1710-2690-65/65/65-16i/18i/18i-M/M/M
Model: ATR451606
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2690)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 15.9 16.1 16.3 17.5 17.8 18.0 18.2
Gain (dBi)
over all Tilts 15.8 ± 0.4 16.0 ± 0.4 16.2 ± 0.5 17.4 ± 0.4 17.6 ± 0.5 17.9 ± 0.5 18.0 ± 0.5
Side lobe suppression for first side
Tri-band
> 17 > 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 1.5 64 ± 3.0 62 ± 4.1 65 ± 4.8 62 ± 3.7 60 ± 4.3 60 ± 4.5
Vertical 3dB beam width (°) 10.1 ± 0.4 9.8 ± 0.5 9.3 ± 0.5 5.8 ± 0.3 5.4 ± 0.3 4.8 ± 0.3 4.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1999 x 349 x 166
147
DXXX-790-960/1710-2690/1710-2690-65/65/65-16i/18i/18i-M/M/M
Model: ATR451606
Accessories
57 57 60
63
Unit: mm
790 - 960
1710 - 2690 X 1710 - 2690
Left Right
X X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
148
DXXX-790-960/1710-2690/1710-2690-65/65/65-17i/18i/18i-M/M/M
Model: ATR451607
Antenna Specifications
Electrical Properties
790 - 960 2 x (1710 - 2690)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 16.8 17.0 17.3 17.5 17.8 18.0 18.2
Gain (dBi)
over all Tilts 16.7 ± 0.4 17.0 ± 0.3 17.2 ± 0.5 17.4 ± 0.5 17.6 ± 0.5 17.9 ± 0.5 18.0 ± 0.5
Side lobe suppression for first side
Tri-band
> 17 > 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 2.0 64 ± 2.0 62 ± 4.1 65 ± 4.8 62 ± 3.7 60 ± 4.3 60 ± 4.5
Vertical 3dB beam width (°) 8.6 ± 0.5 8.2 ± 0.5 7.6 ± 0.5 5.8 ± 0.3 5.4 ± 0.3 4.8 ± 0.3 4.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 30 (790 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2528 x 349 x 166
149
DXXX-790-960/1710-2690/1710-2690-65/65/65-17i/18i/18i-M/M/M
Model: ATR451607
Accessories
57 57 60
63
Unit: mm
790 - 960
1710 - 2690 X 1710 - 2690
Left Right
X X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
150
DXXX-690-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M
Model: ATR451806
Antenna Specifications
Electrical Properties
690 - 960 2 x (1710 - 2690)
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
at mid Tilt 14.4 14.5 14.7 15.1 17.5 17.8 18.2 18.3
Gain (dBi)
over all Tilts 14.3 ±0.5 14.5 ±0.5 14.8 ±0.5 15.0 ±0.5 17.3 ±0.6 17.7 ±0.5 18.1 ±0.6 18.2 ±0.5
Tri-band
Side lobe suppression for first side
> 16 > 17 > 17 > 19 > 19 > 19 > 19 > 19
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ±2.5 64 ±2.0 64 ±2.0 64 ±3.2 65 ±3.9 63 ±3.3 62 ±4.8 60 ±4.5
Vertical 3dB beam width (°) 15.6 ±1.2 13.7 ±0.9 13.1 ±0.8 12.2 ±0.8 7.1 ±0.6 6.5 ±0.5 5.8 ±0.5 5.2 ±0.3
Cross polar ratio (dB) 0° > 19 > 20 > 20 > 22 > 18 > 19 > 20 > 19
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1499 x 359 x 178
Packing dimensions (H x W x D) (mm) 1880 x 425 x 250
Antenna weight (kg) 23.2
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 35.1 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 670 (at 150 km/h)
Wind load (N) Lateral: 180 (at 150 km/h)
Rear side: 560 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 6 x 7/16 DIN Female
Connector position Bottom
151
DXXX-690-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M
Model: ATR451806
Accessories
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20M11 Remote electrical tilt module, a couple of AISG connectors 0.7 kg 1 (Separate packing)
106
60
53
50
1347
1499
Unit: mm
690 - 960
1710 - 2690 X 1710 - 2690
Left Right
X X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
152
DXXX-690-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.5m
Model: ATR4518R13
Antenna Specifications
Electrical Properties
690 - 960 2 x (1710 - 2690)
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable 0 - 10 , continuously adjustable, each band separately
at mid Tilt 14.4 14.5 14.7 15.1 17.5 17.8 18.2 18.3
Gain (dBi)
over all Tilts 14.3 ±0.5 14.5 ±0.5 14.8 ±0.5 15.0 ±0.5 17.3 ±0.6 17.7 ±0.5 18.1 ±0.6 18.2 ±0.5
Side lobe suppression for first side
> 16 > 17 > 17 > 19 > 19 > 19 > 19 > 19
Tri-band
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ±2.5 64 ±2.0 64 ±2.0 64 ±3.2 65 ±3.9 63 ±3.3 62 ±4.8 60 ±4.5
Vertical 3dB beam width (°) 15.6 ±1.2 13.7 ±0.9 13.1 ±0.8 12.2 ±0.8 7.1 ±0.6 6.5 ±0.5 5.8 ±0.5 5.2 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
≥ 30 (690 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 24 > 26 > 26 > 26 > 30 > 30 > 28 > 27
Cross polar ratio (dB) 0° > 19 > 20 > 20 > 22 > 18 > 19 > 20 > 19
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1499 x 359 x 178
Packing dimensions (H x W x D) (mm) 1880 x 425 x 250
Antenna weight (kg) 23.6
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 35.5 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1499
Accessories
Item Model Description Weight Units per antenna
153
DXXX-690-960/1710-2690/1710-2690-65/65/65-15i/17.5i/17.5i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.5m
Model: ATR4518R13
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…….r
HWMxxx……yL
yL yyR
HWMxxx…..yyR
r - Red y - Yellow
L - Left array R - Right array
r
154
DXXX-690-960/1710-2690/1710-2690-65/65/65-16i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4518R6
Antenna Specifications
Electrical Properties
690 - 960 2 x (1710 - 2690)
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 15.5 15.9 16.0 16.1 17.1 17.5 17.8 18.3
Gain (dBi)
over all Tilts 15.5 ± 0.5 15.8 ± 0.5 15.8 ± 0.5 16.0 ± 0.6 17.1 ± 0.5 17.5 ± 0.4 17.7 ± 0.5 18.2 ± 0.4
Side lobe suppression for first side
Tri-band
> 18 > 18 > 18 > 18 > 19 > 19 > 19 > 19
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 1.7 65 ± 1.4 65 ± 1.7 65 ± 2.4 65 ± 4.3 64 ± 3.2 63 ± 4.4 62 ± 4.1
Vertical 3dB beam width (°) 10.3± 0.7 9.5 ± 0.5 9.2 ± 0.6 8.6 ± 0.5 7.1 ± 0.5 6.5 ± 0.5 5.8 ± 0.4 5.3 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
≥ 30 (690 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 26 > 26 > 26 > 26 > 27 > 27 > 27 > 27
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 17 > 17
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
155
DXXX-690-960/1710-2690/1710-2690-65/65/65-16i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.0m
Model: ATR4518R6
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx..….r
HWMxxx….yL
yL yyR
HWMxxx..yyR
r - Red y - Yellow
L - Left array R - Right array
r
156
DXXX-690-960/1710-2690/1710-2690-65/65/65-17i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4518R11
Antenna Specifications
Electrical Properties
690 - 960 2 x (1710 - 2690)
Frequency range (MHz) 1710 - 1920 - 2200 - 2490 -
690 - 803 790 - 862 824 - 894 880 - 960
1990 2200 2490 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 16.5 16.7 16.8 17.0 17.1 17.5 17.8 18.2
Gain (dBi)
over all Tilts 16.4 ± 0.4 16.6 ± 0.3 16.7 ± 0.2 16.8 ± 0.4 17.1 ± 0.5 17.5 ± 0.4 17.8 ± 0.5 18.2 ± 0.3
Tri-band
Side lobe suppression for first side
> 17 > 17 > 17 > 17 > 19 > 19 > 19 > 19
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 1.3 66 ± 1.4 65 ± 1.3 65 ± 1.9 65 ± 4.6 64 ± 4.1 63 ± 3.4 62 ± 4.1
Vertical 3dB beam width (°) 9.0 ± 0.6 8.3 ± 0.4 7.5 ± 0.4 7.2 ± 0.4 7.1 ± 0.5 6.5 ± 0.5 5.8 ± 0.3 5.3 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
≥ 30 (690 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 27 > 27 > 27 > 27 > 27 > 27 > 27 > 27
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
157
DXXX-690-960/1710-2690/1710-2690-65/65/65-17i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 2.6m
Model: ATR4518R11
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
r - Red y - Yellow
L - Left array R - Right array
r
158
DXXX-1710-2200/1710-2200/1710-2200-65/65/65-18i/18i/18i-M/M/M
Model: ATR451807
Antenna Specifications
Electrical Properties
3 x (1710 - 2200)
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Tri-band
Side lobe suppression for first side
> 20 > 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 3 65 ± 3 63 ± 4 61 ± 3
Vertical 3dB beam width (°) 7.4 ± 0.4 6.9 ± 0.4 6.5 ± 0.6 6.0 ± 0.3
Max. power per input (W) 300 (at 50℃ ambient temperature)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 376 x 99
159
DXXX-1710-2200/1710-2200/1710-2200-65/65/65-18i/18i/18i-M/M/M
Model: ATR451807
Accessories
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20M11 Remote electrical tilt module, a couple of AISG connectors 0.7 kg 1 (Separate packing)
62
106
49
Unit: mm
1365
1262
1710 - 2200
Center
1710 - 2200 X 1710 - 2200
Left Right
X X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
160
DXXX-1710-2200/1710-2200/1710-2200-65/65/65-18i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4518R15
Antenna Specifications
Electrical Properties
3 x (1710 - 2200)
Frequency range (MHz)
1710 - 1880 1850 - 1990 1920 - 2170 2170 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 17.4 17.7 17.9 17.9
Gain (dBi)
over all Tilts 17.3 ± 0.4 17.5 ± 0.4 17.7 ± 0.4 17.7 ± 0.4
Side lobe suppression for first side
Tri-band
> 20 > 18 > 18 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 3 65 ± 3 63 ± 4 61 ± 3
Vertical 3dB beam width (°) 7.4 ± 0.4 6.9 ± 0.4 6.5 ± 0.6 6.0 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 28
Front to back ratio, ± 30° (dB) > 25 > 26 > 27 > 27
Cross polar ratio (dB) 0° > 21 > 21 > 20 > 18
Max. power per input (W) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 376 x 99
Packing dimensions (H x W x D) (mm) 1680 x 440 x 170
Antenna weight (kg) 16.7
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 25.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1365
Accessories
Item Model Description Weight Units per antenna
161
DXXX-1710-2200/1710-2200/1710-2200-65/65/65-18i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4518R15
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
162
DXXX-1710-2690/1710-2170/2490-2690-65/65/65-18i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4518R3
Antenna Specifications
Electrical Properties
1710 - 2690 1710 - 2170
Frequency range (MHz) 2490 - 2690
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2170
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable , each band separately
at mid Tilt 17.5 17.9 18.2 18.2 17.5 17.8 18.2
Gain (dBi)
over all Tilts 17.3 ± 0.5 17.7 ± 0.5 18.0 ± 0.5 18.1 ± 0.5 17.4 ± 0.4 17.6 ± 0.4 18.0 ± 0.5
Side lobe suppression for first side
> 17 > 17 > 18 > 17 > 17 > 18 > 18
Tri-band
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 3.8 64 ± 3.2 62 ± 2.3 60 ± 3.8 66 ± 3.4 64 ± 3.1 60 ± 3.5
Vertical 3dB beam width (°) 6.5 ± 0.4 6.0 ± 0.5 5.3 ± 0.3 4.8 ± 0.3 6.4 ± 0.5 5.9 ± 0.4 4.6 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
≥ 30 (1710 - 2170 // 1710 - 2690 MHz)
Interband isolation (dB) ≥ 30 (1710 - 2170 // 2490 - 2690 MHz)
≥ 30 (1710 - 2690 // 2490 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 26 > 25 > 25 > 26 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
163
DXXX-1710-2690/1710-2170/2490-2690-65/65/65-18i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with 3 Integrated RCUs - 1.4m
Model: ATR4518R3
Properties
RET type Integrated RET
RET protocols* AISG 2.0/3GPP
Input voltage range (V) 10 - 30 DC
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol swithing
function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx.…bL
HWMxxx.…yL
bL yL yyR
HWMxxx…yyR
b - Blue y - Yellow
L - Left array R - Right array
164
DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-
M/M/M
Model: ATR451714v01
Antenna Specifications
Electrical Properties
3 x (1710 - 2690)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Tri-band
Side lobe suppression for first side
> 19 > 22 > 20 > 19
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 5.5 65 ± 4.2 64 ± 3.8 60 ± 3.2
Vertical 3dB beam width (°) 6.7 ± 0.5 6.1 ± 0.3 5.4 ± 0.4 5.0 ± 0.2
Max. power per input (W) 250 (at 50℃ ambient temperature)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 376 x 99
165
DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-
M/M/M
Model: ATR451714v01
Accessories
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20M11 Remote electrical tilt module, a couple of AISG connectors 0.7 kg 1 (Separate packing)
62 106
49
Unit: mm
1365
1262
1710 - 2690
1710 - 2690 Center
X 1710 - 2690
Left Right
X X
+45° -45°
+45° -45° +45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
166
DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with Integrated 3 RCUs - 1.4m
Model: ATR4518R14
Antenna Specifications
Electrical Properties
3 x (1710 - 2690)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 17.6 18.0 18.4 18.6
Gain (dBi)
over all Tilts 17.4 ± 0.4 17.8 ± 0.4 18.1 ± 0.4 18.3 ± 0.5
Side lobe suppression for first side
Tri-band
> 19 > 22 > 20 > 19
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 5.5 65 ± 4.2 64 ± 3.8 60 ± 3.2
Vertical 3dB beam width (°) 6.7 ± 0.5 6.1 ± 0.3 5.4 ± 0.4 5.0 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Interband isolation (dB) ≥ 30
Front to back ratio, ± 30° (dB) > 27 > 27 > 29 > 29
Cross polar ratio (dB) 0° > 26 > 25 > 23 > 23
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
106
Antenna dimensions (H x W x D) (mm) 1365 x 376 x 99
Packing dimensions (H x W x D) (mm) 1680 x 440 x 170
Antenna weight (kg) 17.8
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 27.5 (included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1365
Accessories
Item Model Description Weight Units per antenna
167
DXXX-1710-2690/1710-2690/1710-2690-65/65/65-18i/18i/18i-M/M/M-R
EasyRET Tri-Band Antenna with Integrated 3 RCUs - 1.4m
Model: ATR4518R14
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna software
interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol switching
function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
168
B - 4. Quad-band Antenna
790-862/
880-960/ 15.5/ 0-10/0-10/
1710-2690/
65/65/65/65
16/18/18 0-10/0-10
EasyRET2.0 8 x 7/16 DIN-F 1999 x 349 x 166 AQU4518R5 171 R
1710-2690
790-862/
880-960/ 16.5/ 0-10/0-10/
1710-2690/
65/65/65/65
17/18/18 0-10/0-10
EasyRET2.0 8 x 7/16 DIN-F 2528 x 349 x 166 AQU4518R4 173 R
1710-2690
Quad-band
690-862/
880-960/ 14/14.5/ 0-12/0-12/
1710-2690/
65/65/65/65
17.5/17.5 0-10/0-10
EasyRET2.0 8 x 7/16 DIN-F 1499 x 359 x 178 AQU4517R4 175 R
1710-2690
690-803/
824-960/ 14/14.5/ 0-12/0-12/
1710-2690/
65/65/65/65
17.5/17.5 0-10/0-10
EasyRET2.0 8 x 7/16 DIN-F 1499 x 359 x 178 AQU4518R19 177 R
1710-2690
690-803/
824-960/ 0-10/0-10/
1710-2690/
65/65/65/65 15/16/18/18
0-10/0-10
EasyRET2.0 8 x 7/16 DIN-F 2022 x 359 x 178 AQU4518R17 179 R
1710-2690
690-960/
690-960/ 0-10/0-10/
1695-2690/
65/65/65/65 16/16/18/18
2-12/2-12
EasyRET2.0 8 x 7/16 DIN-F 2099 x 429 x 196 AQU4518R24 181 S
1695-2690
690-960/
690-960/ 0-10/0-10/
1695-2690/
65/65/65/65 17/17/18/18
2-12/2-12
EasyRET2.0 8 x 7/16 DIN-F 2769 x 429 x 196 AQU4518R25 183 S
1695-2690
690-960/
1427-2200/ 0-10/2-12/ 8 x 4.3-10
1695-2690/
65/65/65/65 16/17/18/18
2-12/2-12
EasyRET2.0
Female
2000 x 369 x 149 **AQU4518R22 185 SS
1695-2690
790-960/
1710-2690/ 15/17.5/ 0-14/0-10/
1710-2170/
65/65/65/65
17.5/17.5 0-10/0-10
EasyRET1.0 8 x 7/16 DIN-F 1499 x 349 x 166 AQU4518R7 186 T
2490-2690
790-960/
1710-2690/ 0-10/0-10/
1710-2170/
65/65/65/65 16/18/18/18
0-10/0-10
EasyRET1.0 8 x 7/16 DIN-F 1999 x 349 x 166 AQU4518R0 189 T
2490-2690
** Preliminary Issue
B - 4. Quad-band Antenna
790-960/
1710-2690/ 0-10/0-10/
1710-2170/
65/65/65/65 17/18/18/18
0-10/0-10
EasyRET1.0 8 x 7/16 DIN-F 2528 x 349 x 166 AQU4518R1 192 T
2490-2690
698-960/
1710-2690/ 17/ 0-10/0-10/
1710-2690/
65/65/65/65
18/18/17.5 0-10/0-10
EasyRET1.0 8 x 7/16 DIN-F 2688 x 349 x 166 AQU4518R9 195 U
1710-2690
690-960/
1710-2690/ 15/17.5/ 0-14/2-12/
1710-2690/
65/65/65/65
17.5/17.5 2-12/2-12
EasyRET2.0 8 x 7/16 DIN-F 1520 x 369 x 149 AQU4518R14 197 TT
1710-2690
690-960/
1710-2690/ 0-10/2-12/
1710-2690/
65/65/65/65 16/18/18/18
2-12/2-12
EasyRET2.0 8 x 7/16 DIN-F 2000 x 369 x 149 AQU4518R11 200 TT
1710-2690
1710-2170/
1710-2170/ 18/ 0-12/0-12/
2496-2690/
65/65/65/65
18/18/18 0-12/0-12
EasyRET2.0 8 x 7/16 DIN-F 1490 x 299 x 109 AQU4518R8 203 V
2496-2690
1710-2690/
1710-2690/ 0-12/0-12/
1710-2690/
65/65/65/65 18/18/18/18
0-12/0-12
EasyRET2.0 8 x 7/16 DIN-F 1499 x 449 x 115 AQU4518R21 205 VV
1710-2690
** Preliminary Issue
yLT
yL yyR Ly1 Ry2 Ly1 Cg1 Ry2 Ly1 Cy2 Ry3 bL yL yyR bL yL bbR yyR yL yyCL yyyCR yyyyR
yyLB yyyRB
r rr Lr1 Rr2 r1 r1 r r
DXXXX-790-862/880-960/1710-2690/1710-2690-65/65/65/65-
15.5i/16i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs-2.0m
Model: AQU4518R5
Antenna Specifications
Electrical Properties
2 x (1710 - 2690)
Frequency range (MHz) 790 - 862 880 - 960
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Horizontal 3dB beam width (°) 65 ± 2.0 62 ± 2.6 65 ± 5.0 62 ± 3.5 60 ± 3.5 60 ± 4.0
Vertical 3dB beam width (°) 10.5 ± 0.7 9.4 ± 0.6 5.8 ± 0.3 5.4 ± 0.4 4.8 ± 0.2 4.3 ± 0.2
Quad-band
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
Front to back ratio, ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Impedance (Ω) 50
Grounding DC Ground
Accessories
171
DXXXX-790-862/880-960/1710-2690/1710-2690-65/65/65/65-
15.5i/16i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs-2.0m
Model: AQU4518R5
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx...yyR
r - Red y - Yellow
r rr
L - Left array R - Right array
172
DXXXX-790-862/880-960/1710-2690/1710-2690-65/65/65/65-
16.5i/17i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs-2.6m
Model: AQU4518R4
Antenna Specifications
Electrical Properties
2 x (1710 - 2690)
Frequency range (MHz) 790 - 862 880 - 960
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
at mid Tilt 16.2 16.7 17.3 17.8 18.0 18.2
Gain (dBi)
over all Tilts 16.1 ± 0.5 16.5 ± 0.4 17.2 ± 0.5 17.6 ± 0.4 17.8 ± 0.4 18.1 ± 0.5
Side lobe suppression for first side
> 16 > 16 > 16 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 2.2 62 ± 2.5 65 ± 5.0 62 ± 3.5 60 ± 3.5 60 ± 4.0
Vertical 3dB beam width (°) 8.6 ± 0.7 7.6 ± 0.6 5.8 ± 0.4 5.4 ± 0.4 4.8 ± 0.2 4.3 ± 0.2
VSWR < 1.5
Quad-band
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
≥ 28 (790 - 862 // 880 - 960 MHz)
Interband isolation (dB) ≥ 30 (790 - 862 // 1710 - 2690 MHz)
≥ 30 (880 - 960 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 24 > 24 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 >18 > 18
500 (at 50℃ ambient
Max. power per input (W) 250 (at 50℃ ambient temperature)
temperature)
Total power (W) 1000 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2528 x 349 x 166
Packing dimensions (H x W x D) (mm) 2885 x 420 x 245
Antenna weight (kg) 34.0
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 49.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 920 (at 150 km/h)
Wind load (N) Lateral: 305 (at 150 km/h)
Rear side: 955 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0D01 Mechanical downtilt: 0 - 8 ° 2.1 kg 1 (Separate packing)
173
DXXXX-790-862/880-960/1710-2690/1710-2690-65/65/65/65-
16.5i/17i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs-2.6m
Model: AQU4518R4
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...r
HWMxxx…..rr
yL yyR
HWMxxx…..yL
HWMxxx...yyR
r - Red y - Yellow r rr
L - Left array R - Right array
174
DXXXX-690-862/880-960/1710-2690/1710-2690-65/65/65/65-
14i/14.5i/17.5i/17.5i/-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4517R4
Antenna Specifications
Electrical Properties
690 - 862 2 x (1710 - 2690)
Frequency range (MHz) 880 - 960
690 - 803 790 - 862 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
0 - 12 , continuously adjustable, each band
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately
separately
at mid Tilt 13.8 13.9 14.2 17.4 17.8 18.2 18.3
Gain (dBi) over all
14.0 ±0.5 14.1 ±0.3 14.3 ±0.3 17.3 ±0.5 17.7 ±0.5 18.1 ±0.5 18.2 ±0.4
Tilts
Side lobe suppression for first
> 16 > 16 > 15 > 18 > 18 > 18 > 18
side lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ±1.7 64 ±2.6 64 ±3.5 65 ±3.9 63 ±3.3 62 ±4.8 60 ±4.5
Vertical 3dB beam width (°) 15.2 ±2.3 13.3 ±1.8 11.8 ±2.0 7.1 ±0.6 6.5 ±0.5 5.8 ±0.5 5.2 ±0.3
VSWR < 1.5
Quad-band
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
≥ 28 (690 - 862 // 880 - 960 MHz)
≥ 30 (690 - 862 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (880 - 960 // 1710 - 2690 MHz)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 30 > 28 > 28 > 28
Cross polar ratio (dB) 0° > 18 > 20 > 20 > 19 > 19 > 20 > 20
Max. power per input (W) 300 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 700 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1499 x 359 x 178 106
Packing dimensions (H x W x D) (mm) 1880 x 425 x 255
Antenna net weight (kg) 27.1
Bracket weight (kg) 3.6 (2 units)
Packing weight (kg) 40.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1499
175
DXXXX-690-862/880-960/1710-2690/1710-2690-65/65/65/65-
14i/14.5i/17.5i/17.5i/-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4517R4
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...yL
HWMxxx……r
yL yyR
HWMxxx…..rr
HWMxxx...yyR
r - Red y - Yellow
L - Left array R - Right array r rr
176
DXXXX-690-803/824-960/1710-2690/1710-2690-65/65/65/65-
14i/14.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R19
Antenna Specifications
Electrical Properties
824 - 960 2 x (1710 - 2690)
Frequency range (MHz) 690 - 803
824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
0 - 12 , continuously adjustable , each
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
band separately
at mid Tilt 13.8 13.9 14.2 17.4 17.8 18.2 18.3
Gain (dBi)
over all Tilts 14.0 ±0.5 14.1 ±0.3 14.3 ±0.3 17.3 ±0.5 17.7 ±0.5 18.1 ±0.5 18.2 ± 0.4
Vertical 3dB beam width (°) 15.2 ±2.3 12.8 ±2.0 11.8 ±2.0 7.1 ±0.6 6.5 ±0.5 5.8 ±0.5 5.2 ± 0.3
Quad-band
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
≥ 28 (690 - 803 // 824 - 960 MHz)
≥ 30 (690 - 803 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (824 - 960 // 1710 - 2690 MHz)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 30 > 28 > 28 > 28
Cross polar ratio (dB) 0° > 18 > 18 > 20 > 19 > 19 > 20 > 20
Max. power per input (W) 300 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 700 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available. 106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1499 x 359 x 178
Packing dimensions (H x W x D) (mm) 1880 x 425 x 250
Antenna weight (kg) 28.0
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 41.7 (included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1999
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0D01 Mechanical downtilt: 0 - 16 ° 2.1 kg 1 (Separate packing)
177
DXXXX-690-803/824-960/1710-2690/1710-2690-65/65/65/65-
14i/14.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R19
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…….r
yL yyR
HWMxxx……rr
HWMxxx…yyR
r - Red y - Yellow r rr
L - Left array R - Right array
178
DXXXX-690-803/824-960/1710-2690/1710-2690/-65/65/65/65-
15i/16i/18i/18i/-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R17
Antenna Specifications
Electrical Properties
824 - 960 2 x (1710 - 2690)
Frequency range (MHz) 690 - 803
824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid tilt 14.7 15.1 15.4 17.2 17.5 17.8 17.9
Gain (dBi)
over all tilts 14.8 ±0.5 15.1 ±0.5 15.4 ±0.3 17.1 ±0.4 17.4 ±0.5 17.8 ±0.5 17.9 ±0.4
Side lobe suppression for first side
> 18 > 18 > 18 > 18 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ±3.0 63 ±2.7 63 ±3.0 66 ±3.9 64 ±3.3 63 ±4.8 60 ±4.5
Vertical 3dB beam width (°) 12.0 ±1.0 10.1 ±0.9 9.4 ±0.8 6.3 ±0.5 5.7 ±0.4 5.1 ±0.5 4.7 ±0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
Quad-band
≥ 28 (690 - 803 // 824 - 960 MHz)
≥ 30 (690 - 803 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (824 - 960 // 1710 - 2690 MHz)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 27 > 25 > 27 > 30 > 29 > 27 > 26
Cross polar ratio (dB) 0° > 16 > 19 > 19 > 18 > 18 > 18 > 18
Max. power per input (W) 360 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 700 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2022 x 359 x 178
106
Packing dimensions (H x W x D) (mm) 2400 x 430 x 255
Antenna weight (kg) 32.7
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 47.4 (included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
2022
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0D01 Mechanical downtilt: 0 - 12 ° 2.1 kg 1 (Separate packing)
179
DXXXX-690-803/824-960/1710-2690/1710-2690/-65/65/65/65-
15i/16i/18i/18i/-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R17
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx...yyR
r - Red y - Yellow
L - Left array R - Right array r rr
180
DXXXX-690-960/690-960/1695-2690/1695-2690-65/65/65/65-
16i/16i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with Integrated RCUs - 2.0m
Model: AQU4518R24
Antenna Specifications
Electrical Properties
2 x (690 - 960) 2 x (1695 - 2690)
Frequency range (MHz) 1695 - 1920 - 2200 - 2490 -
690 - 803 790 - 862 824 - 894 880 - 960
1990 2200 2490 2690
Polarization +45° , -45°
0 - 10 , continuously adjustable, each band 2 - 12, continuously adjustable, each band
Electrical downtilt (°)
separately separately
at mid Tilt 15.0 15.5 15.8 16.0 17.0 17.2 17.7 18.1
Gain (dBi)
over all Tilts 14.7 ± 0.5 15.3 ± 0.5 15.6 ± 0.5 15.8 ± 0.5 16.8 ± 0.5 17.1 ± 0.5 17.5 ± 0.5 17.9± 0.5
Side lobe suppression for first side
> 16 > 17 > 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)
Vertical 3dB beam width (°) 10.5 ± 0.9 9.5 ± 0.8 9.2 ± 0.7 8.5 ± 0.7 6.8 ± 0.7 5.8 ± 0.5 5.3 ± 0.4 5.0 ± 0.5
Quad-band
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ± 30° (dB) > 23 > 25 > 26 > 26 > 26 > 27 > 27 > 28
Cross polar ratio (dB) 0° > 17 > 18 > 19 > 20 > 15 > 16 > 17 > 17
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 960 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Accessories
Item Model Description Weight Units per antenna
181
DXXXX-690-960/690-960/1695-2690/1695-2690-65/65/65/65-
16i/16i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with Integrated RCUs - 2.0m
Model: AQU4518R24
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...Ry2
182
DXXXX-690-960/690-960/1695-2690/1695-2690-65/65/65/65-
17i/17i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.6m
Model: AQU4518R25
Antenna Specifications
Electrical Properties
2 x (690 - 960) 2 x (1695 - 2690)
Frequency range (MHz) 1695 - 1920 - 2200 - 2490 -
690 - 803 790 - 862 824 - 894 880 - 960
1990 2200 2490 2690
Polarization +45° , -45°
0 - 10, continuously adjustable, each band 2 - 12, continuously adjustable, each band
Electrical downtilt (°)
separately separately
at mid Tilt 15.8 16.4 16.7 17.0 17.0 17.2 17.7 18.1
Gain (dBi)
over all Tilts 15.5 ± 0.5 16.3 ± 0.5 16.5 ± 0.5 16.7 ± 0.5 16.8 ± 0.5 17.1 ± 0.5 17.5 ± 0.5 17.9 ± 0.5
Side lobe suppression for first side
> 16 > 17 > 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 5 65 ± 5 60 ± 5 58 ± 5 65 ± 5 63 ± 5 61 ± 5 60 ± 5
Vertical 3dB beam width (°) 8.8 ± 0.7 8.0 ± 0.6 7.8 ± 0.5 7.5 ± 0.5 6.8 ± 0.7 5.8 ± 0.5 5.3 ± 0.4 5.0 ± 0.5
Quad-band
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ± 30° (dB) > 25 > 26 > 26 > 26 > 26 > 27 > 27 > 28
Cross polar ratio (dB) 0° > 17 > 18 > 19 > 20 > 15 > 16 > 17 > 17
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 960 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
183
DXXXX-690-960/690-960/1695-2690/1695-2690-65/65/65/65-
17i/17i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.6m
Model: AQU4518R25
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…...Ry2
184
DXXXX-690-960/1695-2690/1695-2690/1427-2200-65/65/65/65--
16i/18i/18i/17i- M/M/M/M-R
EasyRET Quad-Band Antenna with Integrated RCUs - 2.0m
Model: AQU4518R22
Preliminary Issue
Antenna Specifications
Electrical Properties
Frequency range (MHz) 690 - 960 2 x (1695 - 2690) 1427 - 2200
Electrical downtilt (°) 0 - 10 2 - 12 2 - 12
Gain (dBi) 15.8 18 17
Side lobe suppression for first side lobe
16 16 16
above main beam (Typ.) (dB)
Horizontal 3dB beam width (°) 65 65 68
Vertical 3dB beam width (°) 9.8 6.5 8
VSWR < 1.5
Front to back ratio, copolar (dB) Typ. 25 Typ. 25 Typ. 25
Cross polar ratio (dB) 0° Typ.18 Typ.18 Typ. 18
Quad-band
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2000 x 369 x 149
Packing dimensions (H x W x D) (mm) 2350 x 450 x 230
Antenna net weight (kg) 29
Mechanical downtilt (°) 0 - 12
Connector 8 x 4.3-10 Female
RET type Integrated RET
RET protocols AISG 2.0 / 3GPP
185
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/65-
15i/17.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R7
Antenna Specifications
Electrical Properties
790 - 960 (r)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable
at mid Tilt 14.3 14.5 14.7
Gain (dBi)
over all Tilts 14.2 ± 0.4 14.4 ± 0.4 14.6 ± 0.5
Side lobe suppression for first side
> 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 3.4 64 ± 3.7 62 ± 4.8
Vertical 3dB beam width (°) 15.5 ± 0.9 15.0 ± 0.9 14.0 ± 1.0
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 24 > 24 > 24
Cross polar ratio (dB) 0° > 20 > 20 > 20
Max. power per input (W) 500 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (yyR) 1710 - 2170 (bL) 2490 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2170 (yL)
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 17.2 17.8 18.0 17.9 17.1 17.5 17.3
Gain (dBi)
over all Tilts 17.1 ± 0.4 17.6 ± 0.4 17.9 ± 0.4 17.7 ± 0.5 17.0 ± 0.4 17.3 ± 0.4 17.3 ± 0.5
Side lobe suppression for first side
> 16 > 16 > 16 > 15 > 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 63 ± 4.0 62 ± 4.0 60 ± 2.3 60 ± 4.8 63 ± 4.8 62 ± 3.7 60 ± 4.5
Vertical 3dB beam width (°) 6.2 ± 0.4 5.8 ± 0.4 5.2 ± 0.3 4.7 ± 0.4 6.2 ± 0.5 5.8 ± 0.5 4.7 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
186
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/
65-15i/17.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R7
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1499 x 349 x 166
106
Packing dimensions (H x W x D) (mm) 1825 x 410 x 235
Antenna weight (kg) 23.2
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 32.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1499
Operational temperature (℃) -40 .. +65
1395
Frontal: 505 (at 150 km/h)
Wind load (N) Lateral: 165 (at 150 km/h)
Rear side: 540 (at 150 km/h)
Quad-band
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0C01 Mechanical downtilt: 0 - 16 ° 2.1 kg 1 (Separate packing)
187
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/
65-15i/17.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R7
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx...yyR
188
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/65-
16i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R0
Antenna Specifications
Electrical Properties
790 - 960 (r)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 15.9 16.1 16.3
Gain (dBi)
over all Tilts 15.8 ± 0.4 16.0 ± 0.4 16.2 ± 0.5
Side lobe suppression for first side
> 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 1.5 64 ± 2.0 62 ± 3.1
Vertical 3dB beam width (°) 10.1 ± 0.4 9.8 ± 0.5 9.3 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Quad-band
Interband isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (yyR) 1710 - 2170 (bL) 2490 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2170 (yL)
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 17.3 17.8 18.0 18.2 17.2 17.7 17.7
Gain (dBi)
over all Tilts 17.1 ± 0.5 17.7 ± 0.5 17.9 ± 0.5 18.1 ± 0.5 17.0 ± 0.4 17.5 ± 0.4 17.6 ± 0.5
Side lobe suppression for first side
> 17 > 17 > 18 > 18 > 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 2.5 62 ± 4.3 60 ± 4.4 60 ± 5.0 65 ± 3.8 62 ± 4.0 60 ± 5.0
Vertical 3dB beam width (°) 5.8 ± 0.3 5.4 ± 0.4 4.8 ± 0.2 4.3 ± 0.3 5.8 ± 0.3 5.4 ± 0.4 4.3 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 30
Front to back ratio , ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 250 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
189
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/65-
16i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R0
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1999 x 349 x 166
Packing dimensions (H x W x D) (mm) 2350 x 415 x 240
Antenna weight (kg) 28.0
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 40.3 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1999
Radome colour Light grey
1892
Operational temperature (℃) -40 .. +65
Frontal: 705 (at 150 km/h)
Wind load (N) Lateral: 230 (at 150 km/h)
Rear side: 730 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
190
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/65-
16i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R0
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
Quad-band
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx...yyR
191
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/65-
17i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.6m
Model: AQU4518R1
Antenna Specifications
Electrical Properties
790 - 960 (r)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 16.8 17.0 17.3
Gain (dBi)
over all Tilts 16.6 ±0.4 16.9 ±0.4 17.2 ±0.5
Side lobe suppression for first side
> 17 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ±2.0 64 ±2.5 62 ±2.8
Vertical 3dB beam width (°) 8.6 ±0.4 8.2 ±0.4 7.6 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ±30° (dB) > 28 > 28 > 28
Cross polar ratio (dB) 0° > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (yyR) 1710 - 2170 (bL) 2490 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2170 (yL)
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 17.3 17.8 18.0 18.2 17.2 17.7 17.7
Gain (dBi)
over all Tilts 17.3 ±0.6 17.6 ±0.6 17.9 ±0.6 18.1 ±0.6 17.1 ±0.5 17.5 ±0.5 17.5 ±0.4
Side lobe suppression for first side
> 16 > 17 > 18 > 18 > 16 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ±5.0 62 ±4.8 60 ±3.9 60 ±5.0 65 ±3.7 62 ±4.3 60 ±4.8
Vertical 3dB beam width (°) 5.8 ±0.3 5.4 ±0.4 4.8 ±0.2 4.3 ±0.3 5.8 ±0.4 5.3 ±0.4 4.3 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 30
Front to back ratio , ±30° (dB) > 28 > 28 > 28 > 28 > 28 > 28 > 28
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 250 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
192
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/65-
17i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.6m
Model: AQU4518R1
2528
Frontal: 920 (at 150 km/h)
2424
Wind load (N) Lateral: 305 (at 150 km/h)
Rear side: 955 (at 150 km/h)
Quad-band
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0D01 Mechanical downtilt: 0 - 8 ° 2.1 kg 1 (Separate packing)
193
DXXXX-790-960/1710-2690/1710-2170/2490-2690-65/65/65/65-
17i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.6m
Model: AQU4518R1
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
194
DXXXX-698-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
17i/18i/18i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.6m
Model: AQU4518R9
Antenna Specifications
Electrical Properties
698 - 960 3 x (1710 - 2690)
Frequency range (MHz)
698 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 16.2 16.5 16.7 17.0
over all Tilts 16.1 ±0.5 16.3 ±0.4 16.5 ±0.4 16.8 ±0.4
at mid Tilt 17.1 17.3 17.1 17.6
Gain (dBi) Bottom
over all Tilts 16.9 ±0.5 17.1 ±0.3 17.0 ±0.4 17.4 ±0.5
at mid Tilt 16.8 17.1 16.8 17.3
Top
over all Tilts 16.7 ±0.5 17.0 ±0.4 16.7 ±0.4 17.1 ±0.5
Side lobe suppression for first side
> 17 > 18 > 17 > 17 > 17 > 17 >17 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 67 ±1.9 66 ±3.5 65 ±2.4 62 ±3.3 63 ±3.4 62 ±2.8 61 ±3.7 60 ±3.1
Quad-band
Vertical 3dB beam width (°) 8.8 ±0.6 8.5 ±0.4 8.0 ±0.3 7.4 ±0.3 7.4 ±0.5 6.8 ±0.5 6.0 ±0.4 5.5 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 30 (698 - 960 // 1710 - 2690 MHz)
Interband isolation (dB) ≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25 > 24 > 24 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 17 > 17 > 17 > 17
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 1200 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Accessories
Item Model Description Weight Units per antenna
195
DXXXX-698-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
17i/18i/18i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.6m
Model: AQU4518R9
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
196
DXXXX-690-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
15i/17.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R14
Antenna Specifications
Electrical Properties
690 - 960 (r)
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 14 , continuously adjustable
at mid Tilt 14.3 14.2 14.2 14.5
Gain (dBi)
over all Tilts 14.2 ±0.3 14.2 ±0.2 14.2 ±0.2 14.4 ±0.3
Side lobe suppression for first side
> 15 > 15 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ±1.1 67 ±0.8 65 ±1.4 65 ±1.2
Vertical 3dB beam width (°) 15.3 ±0.9 13.7 ±0.4 13.0 ±0.6 12.1 ±0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Quad-band
Interband isolation (dB) ≥ 28 (690 - 960 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 26 > 26 > 25
Cross polar ratio (dB) 0° > 21 > 16 > 16 > 16
Max. power per input (W) 300 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (yL) / 1710 - 2690 (yyyR) 1710 - 2690 (yyC)
Frequency range (MHz) 1710 - 1920 - 2200 - 2490 - 1710 - 1920 - 2200 - 2490 -
1990 2200 2490 2690 1990 2200 2490 2690
Polarization +45° , -45° +45° , -45°
Electrical downtilt (°) 2 - 12 , continuously adjustable, each band separately
at mid Tilt 17.2 17.8 17.8 18.2 17.0 17.0 17.5 18.0
Gain (dBi)
over all Tilts 17.0 ±0.5 17.7 ±0.4 17.5 ±0.3 18.1 ±0.3 16.8 ±0.5 16.8 ±0.4 17.2 ±0.4 17.8 ±0.3
Side lobe suppression for first side
> 15 > 15 > 16 > 16 > 15 > 15 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ±5.0 63 ±3.0 60 ±3.0 60 ±2.0 64 ±4.0 63 ±3.0 63 ±3.0 60 ±4.0
Vertical 3dB beam width (°) 7.2 ±0.4 6.5 ±0.3 5.8 ±0.3 5.3 ±0.2 7.2 ±0.4 6.5 ±0.3 5.8 ±0.3 5.3 ±0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 28 (690 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 16 > 16 > 16 > 16 > 16 > 16 > 16 > 16
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
197
DXXXX-690-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
15i/17.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R14
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1520 x 369 x 149 106
Packing dimensions (H x W x D) (mm) 1850 x 450 x 230
Antenna net weight (kg) 26.8
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 37 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1414
1520
Operational temperature (℃) -40 .. +65
Frontal: 730 (at 150 km/h)
Wind load (N) Lateral: 145 (at 150 km/h)
Rear side: 725 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
198
DXXXX-690-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
15i/17.5i/17.5i/17.5i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R14
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
Quad-band
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…......yL
HWMxxx……….r
yL yyC yyyR
HWMxxx……yyC
HWMxxx.....yyyR
r - Red y - Yellow
L - Left array C - Center array r
R - Right array
199
DXXXX-690-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
16i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R11
Antenna Specifications
Electrical Properties
690 - 960 (r1)
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable
at mid Tilt 15.4 15.7 15.9 16.1
Gain (dBi)
over all Tilts 15.3 ±0.3 15.6 ±0.2 15.8 ±0.3 16.0 ±0.4
Side lobe suppression for first side
> 15 > 15 > 15 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ±1.0 67 ±1.0 67 ±1.1 65 ±2.0
Vertical 3dB beam width (°) 10.8 ±0.9 9.5 ±0.3 9.2 ±0.3 8.5 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 26 ≥ 28
Interband isolation (dB) ≥ 28 (690 - 960 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20
Max. power per input (W) 300 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (Ly1) / 1710 - 2690 (Ry3) 1710 - 2690 (Cy2)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 2 - 12 , continuously adjustable, each band separately
at mid Tilt 17.4 17.8 18.0 18.4 17.1 17.6 17.7 18.2
Gain (dBi)
over all Tilts 17.3 ±0.4 17.7 ±0.4 17.9 ±0.4 18.3 ±0.3 17.0 ±0.4 17.5 ±0.4 17.6 ±0.4 18.0 ±0.4
Side lobe suppression for first side
> 15 > 15 > 15 > 15 > 15 > 15 > 15 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ±2.0 66 ±2.0 61 ±3.0 60 ±2.0 68 ±3.0 65 ±4.0 62 ±3.0 56 ±3.0
Vertical 3dB beam width (°) 6.9 ±0.3 5.9 ±0.3 5.3 ±0.2 4.8 ±0.2 6.4 ±0.4 5.8 ±0.3 5.7 ±0.3 4.7 ±0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
≥ 28 (690 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 15 > 15 > 15 > 15 > 15 > 15 > 15 > 15
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
200
DXXXX-690-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
16i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R11
Mechanical Properties
106
Antenna dimensions (H x W x D) (mm) 1999 x 369 x 149
Packing dimensions (H x W x D) (mm) 2265 x 435 x 240
Antenna net weight (kg) 28.8
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 43.6 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
1999
1891
Frontal: 985 (at 150 km/h)
Wind load (N) Lateral: 195 (at 150 km/h)
Quad-band
Rear side: 980 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
201
DXXXX-690-960/1710-2690/1710-2690/1710-2690-65/65/65/65-
16i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 2.0m
Model: AQU4518R11
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx……Ry3
r - Red y - Yellow
r1
L - Left array C - Center array
R - Right array
202
DXXXX-1710-2170/1710-2170/2490-2690/2490-2690-
65/65/65/65-18i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R8
Antenna Specifications
Electrical Properties
2 x (1710 - 2170)
Frequency range (MHz) 2 x (2490 - 2690)
1710 - 1990 1920 - 2170
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 17.5 17.8 18.2
Gain (dBi)
over all Tilts 17.4 ± 0.4 17.7 ± 0.4 18.1 ± 0.5
Side lobe suppression for first side
> 17 > 18 > 18
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 3.5 64 ± 4.1 60 ± 3.4
Vertical 3dB beam width (°) 6.4 ± 0.5 5.9 ± 0.4 4.6 ± 0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
Quad-band
≥ 30 (1710 - 2170 // 1710 - 2170 MHz)
Interband isolation (dB) ≥ 30 (1710 - 2170 // 2490 - 2690 MHz)
≥ 30 (2490 - 2690 // 2490 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 20 > 20
Max. power per input (W) 250 (at 50℃ ambient temperature)
Total power (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1490 x 299 x 109
Packing dimensions (H x W x D) (mm) 1790 x 350 x 180
Antenna weight (kg) 18.7
Clamps weight (kg) 3.0 (2 units)
Antenna packing weight (kg) 25.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 535 (at 150 km/h)
Wind load (N) Lateral: 110 (at 150 km/h)
Rear side: 615 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
203
DXXXX-1710-2170/1710-2170/2490-2690/2490-2690-
65/65/65/65-18i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R8
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx…..yL
HWMxxx…bbR bL yL bbRyyR
HWMxxx….yyR
b - Blue y - Yellow
L - Left array R - Right array
204
DXXXX-1710-2690/1710-2690/1710-2690/1710-2690-65/65/65/65-
18i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R21
Antenna Specifications
Electrical Properties
4 x (1710 - 2690)
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 12 , continuously adjustable, each band separately
at mid Tilt 17.4 17.7 17.9 18.3
Gain (dBi)
over all Tilts 17.2 ±0.5 17.5 ±0.5 17.7 ±0.5 18.0 ±0.5
Side lobe suppression for first side
> 18 > 18 > 19 > 20
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ±5 64 ±5 61 ±5 60 ±5
Vertical 3dB beam width (°) 6.8 ±0.5 6.1 ±0.4 5.4 ±0.4 5.0 ±0.3
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Quad-band
Interband isolation (dB) ≥ 28 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 27 > 28 > 28 > 28
Cross polar ratio (dB) 0° > 22 > 22 > 22 > 23
Max. power per input (W) 250 (at 50℃ ambient temperature)
Total power (W) 800 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
205
DXXXX-1710-2690/1710-2690/1710-2690/1710-2690-65/65/65/65-
18i/18i/18i/18i-M/M/M/M-R
EasyRET Quad-Band Antenna with 4 Integrated RCUs - 1.4m
Model: AQU4518R21
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
206
B - 5. Penta-band Antenna
790-862/
880-960/ 0-10/0-10/
65/65/ 15.5/16/18/
1710-2690/
65/65/65 18/18
0-10/0-10/ EasyRET2.0 10 x 7/16 DIN-F 1999 x 349 x 166 APE4518R0 209 W
1710-2170/ 0-10
2490-2690
790-862/
880-960/ 0-10/0-10/
65/65/ 16.5/17/
1710-2690/
65/65/65 18/18/18
0-10/0-10/ EasyRET2.0 10 x 7/16 DIN-F 2528 x 349 x 166 APE4518R1 212 W
1710-2170/ 0-10
2490-2690
690-862/
880-960/ 0-10/0-10/
65/65/ 16.5/17/
1710-2690/ 0-10/0-10/ EasyRET2.0 10 x 7/16 DIN-F 2769 x 359 x 178 **APE4518R12 215 WW
Penta-band
Hexa-band
65/65/65 17.5/18/18
1710-2690/ 0-10
1710-2690
698-960/
1710-2690/ 0-10/0-10/
65/65/ 17/18/18/
1710-2690/
65/65/65 17.5/17.5
0-10/0-10/ EasyRET1.0 10 x 7/16 DIN-F 2688 x 349 x 166 APE4517R0 217 X
1710-2690/ 0-10
1710-2690
** Preliminary Issue
B - 6. Hexa-band Antenna
690-862/
880-960/
14/14.5/ 2-14/2-14/
1710-2690/ 65/65/65/
1710-2690/ 65/65/65
17.5/17.5/ 2-12/2-12/ EasyRET2.0 12 x 7/16 DIN-F 1520 x 369 x 149 ASI4518R11 219 XX
17/17.5 2-12/2-12
1710-2200/
2490-2690
690-862/
880-960/
0-10/0-10/
1710-2690/ 65/65/65/ 16.5/17/18/
1710-2690/ 65/65/65 18/17.5/17.5
0-10/0-10/ EasyRET2.0 12 x 7/16 DIN-F 2769 x 359 x 178 ASI4518R4 222 Y
0-10/0-10
1710-2690/
1710-2690
690-960/
690-960/
17/17/17.5/ 0-10/0-10/
1695-2690/ 65/65/65/
1695-2690/ 65/65/65
17.5/17.5/ 2-12/2-12/ EasyRET2.0 12 x 7/16 DIN-F 2769 x 429 x 196 ASI4518R10 225 Z
17.5 2-12/2-12
1695-2690/
1695-2690
** Preliminary Issue
r rr r1 r2 r1 r2 r Lr1 Rr2
r rr
DXXXXX-790-862/880-960/1710-2690/1710-2170/2490-2690-
65/65/65/65/65-15.5i/16i/18i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.0m
Model: APE4518R0
Antenna Specifications
Electrical Properties
Frequency range (MHz) 790 - 862 (r) 880 - 960 (rr)
Polarization +45°, -45°
Electrical downtilt (°) 0 - 10, continuously adjustable, each band separately
at mid Tilt 15.5 15.8
Gain (dBi)
over all Tilts 15.3 ± 0.3 15.7 ± 0.4
Side lobe suppression for first side
> 16 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 2.7 62 ± 3.7
Vertical 3dB beam width (°) 10.5 ± 0.7 9.4 ± 0.6
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (790 - 862 // 880 - 960 MHz)
Front to back ratio , ± 30° (dB) > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Penta-band
Hexa-band
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (yR) 1710 - 2170 (bL) 2490 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2170 (yyL)
Polarization +45°, -45°
Electrical downtilt (°) 0 - 10, continuously adjustable, each band separately
at mid Tilt 17.3 17.8 18.0 18.2 17.2 17.7 17.7
Gain (dBi)
over all Tilts 17.2 ± 0.5 17.7 ± 0.4 17.9 ± 0.4 18.0 ± 0.5 17.1 ± 0.5 17.5 ± 0.4 17.5 ± 0.4
Side lobe suppression for first side
> 16 > 17 > 17 > 17 > 16 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 5.0 62 ± 3.5 60 ± 3.5 60 ± 4.0 65 ± 3.8 62 ± 3.2 60 ± 3.6
Vertical 3dB beam width (°) 5.8 ± 0.4 5.4 ± 0.4 4.8 ± 0.2 4.3 ± 0.2 5.8 ± 0.4 5.4 ± 0.4 4.3 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 30 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio , ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 250 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
209
DXXXXX-790-862/880-960/1710-2690/1710-2170/2490-2690-
65/65/65/65/65-15.5i/16i/18i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.0m
Model: APE4518R0
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1999 x 349 x 166
Packing dimensions (H x W x D) (mm) 2350 x 415 x 240
Antenna weight (kg) 31.5
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 45.6 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 705 (at 150 km/h)
Wind load (N) Lateral: 230 (at 150 km/h)
Rear side: 730 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 10 x 7/16 DIN Female
Connector position Bottom
Accessories
210
DXXXXX-790-862/880-960/1710-2690/1710-2170/2490-2690-
65/65/65/65/65-15.5i/16i/18i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.0m
Model: APE4518R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Penta-band
Hexa-band
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
211
DXXXXX-790-862/880-960/1710-2690/1710-2170/2490-2690-
65/65/65/65/65-16.5i/17i/18i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.6m
Model: APE4518R1
Antenna Specifications
Electrical Properties
Frequency range (MHz) 790 - 862 (r) 880 - 960 (rr)
Polarization +45°, -45°
Electrical downtilt (°) 0 - 10, continuously adjustable, each band separately
at mid Tilt 16.2 16.7
Gain (dBi)
over all Tilts 16.1 ± 0.5 16.5 ± 0.4
Side lobe suppression for first side
> 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 1.9 62 ± 3.8
Vertical 3dB beam width (°) 8.6 ± 0.7 7.6 ± 0.6
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28 (790 - 862 // 880 - 960 MHz )
Front to back ratio , ± 30° (dB) > 24 > 24
Cross polar ratio (dB) 0° > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (yR) 1710 - 2170 (bL) 2490 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2170 (yyL)
Polarization +45°, -45°
Electrical downtilt (°) 0 - 10, continuously adjustable , each band separately
at mid Tilt 17.3 17.8 18.0 18.2 17.2 17.7 17.7
Gain (dBi)
over all Tilts 17.2 ± 0.5 17.7 ± 0.4 17.9 ± 0.4 18.0 ± 0.5 17.1 ± 0.5 17.5 ± 0.4 17.5 ± 0.4
Side lobe suppression for first side
> 16 > 17 > 17 > 17 > 16 > 17 > 17
lobe above main beam (dB)
Horizontal 3dB beam width (°) 65 ± 5.0 62 ± 3.5 60 ± 3.5 60 ± 4.0 65 ± 3.8 62 ± 3.2 60 ± 3.6
Vertical 3dB beam width (°) 5.8 ± 0.4 5.4 ± 0.4 4.8 ± 0.2 4.3 ± 0.2 5.8 ± 0.4 5.4 ± 0.4 4.3 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 30 (790 - 960 // 1710 - 2690 MHz)
Front to back ratio , ± 30° (dB) > 25 > 25 > 25 > 25 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 18 > 18 > 18 > 18 > 18 > 18 > 18
Max. power per input (W) 250 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
212
DXXXXX-790-862/880-960/1710-2690/1710-2170/2490-2690-
65/65/65/65/65-16.5i/17i/18i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.6m
Model: APE4518R1
106
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2528 x 349 x 166
Packing dimensions (H x W x D) (mm) 2885 x 420 x 245
Antenna weight (kg) 35.6
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 51.6 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
2528
Frontal: 920 (at 150 km/h)
Wind load (N) Lateral: 305 (at 150 km/h)
1827
Rear side: 955 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 10 x 7/16 DIN Female
Connector position Bottom
Penta-band
Hexa-band
Accessories
Item Model Description Weight Units per antenna
213
DXXXXX-790-862/880-960/1710-2690/1710-2170/2490-2690-
65/65/65/65/65-16.5i/17i/18i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.6m
Model: APE4518R1
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
214
DXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2690-
65/65/65/65/65-16.5i/17i/17.5i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.6m
Model: APE4518R12
Preliminary Issue
Electrical Properties
690 - 862 3 x (1710 - 2690)
Frequency range (MHz) 880 - 960
690 - 803 790 - 862 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45°, -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately
at mid Tilt 16.2 16.5 16.9
over all Tilts 16.0 ± 0.5 16.3 ± 0.5 16.8 ± 0.6
at mid Tilt 17.3 17.4 17.6 18.1
Gain (dBi) Bottom
over all Tilts 17.2 ± 0.5 17.4 ± 0.5 17.5 ± 0.6 18.0 ± 0.6
at mid Tilt 16.9 17.2 17.4 17.5
Top
over all Tilts 16.8 ± 0.5 17.1 ± 0.3 17.2 ± 0.5 17.5 ± 0.5
Side lobe suppression for first side lobe
> 20 > 18 > 17 > 20 > 20 > 19 > 19
above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 2.7 65 ± 2.9 63 ± 4.1 66 ± 4.7 63 ± 3.3 61 ± 5.2 60 ± 4.4
Vertical 3dB beam width (°) 8.6 ± 1.1 7.4 ± 0.9 6.5 ± 0.6 7.6 ± 0.6 6.8 ± 0.5 6.1 ± 0.5 5.6 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
≥ 28 (690 - 862 // 880 - 960 MHz)
≥ 30 (690 - 862 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (880 - 960 // 1710 - 2690 MHz)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Penta-band
Hexa-band
Front to back ratio, ± 30° (dB) > 25 > 27 > 26 > 30 > 30 > 27 > 27
Cross polar ratio (dB) 0° > 18 > 22 > 22 > 19 > 19 > 21 > 20
Max. power per input (W) 400 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 1000 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2769 x 359 x 178
Packing dimensions (H x W x D) (mm) 2980 x 425 x 255
Antenna weight (kg) 43.5
Clamps weight (kg) 5.8 (2 units)
Antenna packing weight (kg) 62 (included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 1335 (at 150 km/h)
Wind load (N) Lateral: 365 (at 150 km/h)
Rear side: 1115 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 10 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Downtilt kit ASMDT0F01 Mechanical downtilt: 0 - 8 ° 3.1 kg 1 (Separate packing)
215
DXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2690-
65/65/65/65/65-16.5i/17i/17.5i/18i/18i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.6m
Model: APE4518R12
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
216
DXXXXX-698-960/1710-2690/1710-2690/1710-2690/1710-2690-
65/65/65/65/65-17i/18i/18i/17.5i/17.5i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.6m
Model: APE4517R0
Antenna Specifications
Electrical Properties
698 - 960 4 x (1710 - 2690)
Frequency range (MHz)
698 - 803 790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45°, -45°
Electrical downtilt (°) 0 - 10, continuously adjustable, each band separately
at mid Tilt 16.2 16.5 16.7 17.0
over all Tilts 16.1 ±0.5 16.3 ±0.4 16.5 ±0.4 16.8 ±0.4
at mid Tilt 17.1 17.3 17.1 17.6
Gain (dBi) Bottom
over all Tilts 16.9 ±0.5 17.1±0.3 17.0 ±0.4 17.4 ±0.5
at mid Tilt 16.8 17.1 16.8 17.3
Top
over all Tilts 16.7 ±0.5 17.0 ±0.4 16.7 ±0.4 17.1 ±0.5
Side lobe suppression for first side lobe
> 17 > 17 > 17 > 17 > 17 > 17 > 17 > 16
above main beam (dB)
Horizontal 3dB beam width (°) 67 ±1.9 66 ±3.5 65 ±2.4 62 ±3.3 63 ±3.4 62 ±2.8 61 ±3.7 60 ±3.1
Vertical 3dB beam width (°) 8.8 ±0.6 8.5 ±0.4 8.0 ±0.3 7.4 ±0.3 7.4 ±0.5 6.8 ±0.5 6.0 ±0.4 5.5 ±0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
≥ 30 (698 - 960 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 25 > 24 > 24 > 25 > 25
Penta-band
Hexa-band
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 20 > 17 >17 > 17 > 17
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 1200 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2688 x 349 x 166
Packing dimensions (H x W x D) (mm) 2960 x 435 x 250
Antenna weight (kg) 38.0
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 49.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
2688
2580
1834
Accessories
217
DXXXXX-698-960/1710-2690/1710-2690/1710-2690/1710-2690-
65/65/65/65/65-17i/18i/18i/17.5i/17.5i-M/M/M/M/M-R
EasyRET Penta-Band Antenna with 5 Integrated RCUs - 2.6m
Model: APE4517R0
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN 60950-1 (Safety), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN 301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
HWMxxx……..….r
yLT yyyRT
HWMxxx……..yLT
HWMxxx……yyLB
HWMxxx..…yyyRT yyLB yyyyRB
HWMxxx…yyyyRB
r
r - Red y - Yellow
L - Left array R - Right array
T - Top array B - Bottom array
218
DXXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2200/2490-
2690-65/65/65/65/65/65-14i/14.5i/17.5i/17.5i/17i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with 6 Integrated RCUs - 1.4m
Model: ASI4518R11
Antenna Specifications
Electrical Properties
690 - 862 (r1) 1710 - 2690 (Cy2)
Frequency range (MHz) 880 - 960 (r2)
690 - 803 790 - 862 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45° +45° , -45°
2 - 14 , continuously adjustable , each
Electrical downtilt (°) 2 - 12 , continuously adjustable
band separately
at mid Tilt 13.8 13.7 14.0 17.0 17.2 17.7 18.2
Gain (dBi)
over all Tilts 13.7 ± 0.3 13.7 ± 0.5 13.9 ± 0.3 16.8 ± 0.5 17.0 ± 0.4 17.6 ± 0.5 17.8 ± 0.5
Side lobe suppression for first side
> 16 > 16 > 15 > 15 > 16 > 16 > 15
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 3.0 65 ± 2.6 64 ± 3.2 63 ± 5.1 62 ± 5.0 63 ± 4.0 58 ± 3.0
Vertical 3dB beam width (°) 15.5 ± 2.1 13.6 ± 1.8 12.3 ± 1.8 6.3 ± 0.4 5.8 ± 0.3 5.0 ± 0.2 4.7 ± 0.2
VSWR < 1.5 < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28
Interband isolation (dB) ≥ 28 ≥ 28
Front to back ratio , ± 30° (dB) > 23 > 25 > 25 > 25 > 27 > 27 > 27
Cross polar ratio (dB) 0° > 18 > 20 > 20 > 18 > 16 > 15 > 16
Max. power per input (W) 500 (at 50℃ ambient temperature) * 250 (at 50℃ ambient temperature) *
Penta-band
Hexa-band
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Electrical Properties
1710 - 2690 (Ly1) 1710 - 2200 (Rb1) 2490 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690 1710 - 1990 1920 - 2200 (Ry3)
Polarization +45° , -45°
Electrical downtilt (°) 2 - 12 , continuously adjustable , each band separately
at mid Tilt 17.2 17.8 17.8 18.2 16.9 17.5 17.8
Gain (dBi)
over all Tilts 17.0 ± 0.5 17.7 ± 0.4 17.5 ± 0.3 18.1 ± 0.3 16.7 ± 0.5 17.4 ± 0.4 17.7 ± 0.3
Side lobe suppression for first side
> 16 > 17 > 17 > 16 > 15 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 3.0 66 ± 3.0 63 ± 3.0 60 ± 2.0 68 ± 3.0 66 ± 3.0 60 ± 3.0
Vertical 3dB beam width (°) 6.6 ± 0.4 6.1 ± 0.4 5.4 ± 0.4 4.9 ± 0.4 6.4 ± 0.5 5.8 ± 0.5 4.8 ± 0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ± 30° (dB) > 27 > 27 > 27 > 27 > 25 > 25 > 25
Cross polar ratio (dB) 0° > 20 > 18 > 15 > 17 > 18 > 16 > 18
Max. power per input (W) 250 (at 50℃ ambient temperature) *
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
219
DXXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2200/2490-
2690-65/65/65/65/65/65-14i/14.5i/17.5i/17.5i/17i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with 6 Integrated RCUs - 1.4m
Model: ASI4518R11
Mechanical Properties
106
Antenna dimensions (H x W x D) (mm) 1520 x 369 x 149
Packing dimensions (H x W x D) (mm) 1790 x 435 x 240
Antenna weight (kg) 29.0
Clamps weight (kg) 3.6 (2 units)
Antenna packing weight (kg) 39.2 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
1520
1414
Frontal: 730 (at 150 km/h)
Wind load (N) Lateral: 145 (at 150 km/h)
Rear side: 725 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 12 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
220
DXXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2200/2490-
2690-65/65/65/65/65/65-14i/14.5i/17.5i/17.5i/17i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with 6 Integrated RCUs - 1.4m
Model: ASI4518R11
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
Penta-band
Hexa-band
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx…….Cy2
HWMxxx…….Ly1
Ly1 Cy2 Rb1 Ry3
HWMxxx………r1
HWMxxx…….Rb1
HWMxxx…....Ry3
r1 r2
HWMxxx………r2
221
DXXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2690/1710-
2690-65/65/65/65/65/65-16.5i/17i/18i/18i/17.5i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with 6 Integrated RCUs - 2.6m
Model: ASI4518R4
Antenna Specifications
Electrical Properties
690 - 862 4 x (1710 - 2690)
Frequency range (MHz) 880 - 960
690 - 803 790 - 862 1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45°, -45°
Electrical downtilt (°) 0 - 10, continuously adjustable , each band separately
at mid Tilt 16.2 16.5 16.9
over all Tilts 16.0 ± 0.5 16.3 ± 0.5 16.8 ± 0.6
at mid Tilt 17.3 17.4 17.6 18.1
Gain (dBi) Bottom
over all Tilts 17.2 ± 0.5 17.4 ± 0.5 17.5 ± 0.6 18.0 ± 0.6
at mid Tilt 16.9 17.2 17.4 17.5
Top
over all Tilts 16.8 ± 0.5 17.1 ± 0.3 17.2 ± 0.5 17.5 ± 0.5
Side lobe suppression for first side lobe
> 20 > 18 > 17 > 20 > 20 > 19 > 19
above main beam (dB)
Horizontal 3dB beam width (°) 66 ± 2.7 65 ± 2.9 63 ± 4.1 66 ± 4.7 63 ± 3.3 61 ± 5.2 60 ± 4.4
Vertical 3dB beam width (°) 8.6 ± 1.1 7.4 ± 0.9 6.5 ± 0.6 7.6 ± 0.6 6.8 ± 0.5 6.1 ± 0.5 5.6 ± 0.2
VSWR < 1.5
Cross polar isolation (dB) ≥ 28 ≥ 28 ≥ 28
≥ 28 (690 - 862 // 880 - 960 MHz)
≥ 30 (690 - 862 // 1710 - 2690 MHz)
Interband isolation (dB)
≥ 30 (880 - 960 // 1710 - 2690 MHz)
≥ 30 (1710 - 2690 // 1710 - 2690 MHz)
Front to back ratio, ± 30° (dB) > 25 > 27 > 26 > 30 > 30 > 27 > 27
Cross polar ratio (dB) 0° > 18 > 22 > 22 > 19 > 19 > 21 > 20
Max. power per input (W) 400 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 1000 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -150 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2769 x 359 x 178
Packing dimensions (H x W x D) (mm) 2980 x 425 x 255
Antenna weight (kg) 46.0
Clamps weight (kg) 5.8 (2 units)
Antenna packing weight (kg) 64.5 (included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
2769
Accessories
222
DXXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2690/1710-
2690-65/65/65/65/65/65-16.5i/17i/18i/18i/17.5i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with 6 Integrated RCUs - 2.6m
Model: ASI4518R4
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Penta-band
Hexa-band
Certification: CE, FCC, IC, RCM
HWMxxx…..yyLB
yLT yyyRT
HWMxxx…….yLT
HWMxxx……….r
HWMxxx…yyyRT yyLB yyyyRB
HWMxxx..yyyyRB
r rr
HWMxxx………rr
r - Red y - Yellow
L - Left array R - Right array
T - Top array B -Bottom array
223
DXXXXXX-690-862/880-960/1710-2690/1710-2690/1710-2690/1710-
2690-65/65/65/65/65/65-16.5i/17i/18i/18i/17.5i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with 6 Integrated RCUs - 2.6m
Model: ASI4518R4
224
DXXXXXX-690-960/690-960/1695-2690/1695-2690/1695-2690/1695-
2690-65/65/65/65/65/65-17i/17i/17.5i/17.5i/17.5i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with Integrated RCUs - 2.6m
Model: ASI4518R10
Antenna Specifications
Electrical Properties
2 x (690 - 960) 4 x (1695 - 2690)
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1695 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable , each band separately 2 - 12 , continuously adjustable , each band separately
at mid Tilt 15.8 16.5 16.7 17.0
over all Tilts 15.5 ± 0.5 16.3 ± 0.5 16.5 ± 0.5 16.7 ± 0.5
at mid Tilt 16.6 17.0 17.2 17.6
Gain (dBi) Bottom
over all Tilts 16.4 ± 0.6 16.8 ± 0.5 17.0 ± 0.5 17.4 ± 0.5
at mid Tilt 16.6 17.0 17.2 17.6
Top
over all Tilts 16.4 ± 0.6 16.8 ± 0.5 17.0 ± 0.5 17.4 ± 0.5
Side lobe suppression for first side lobe
> 16 > 17 > 17 > 17 > 16 > 16 > 16 > 16
above main beam (dB)
Horizontal 3dB beam width (°) 68 ± 5 65 ± 5 62 ± 5 60 ± 5 65 ± 5 63 ± 5 61 ± 5 60 ± 5
Vertical 3dB beam width (°) 8.8 ± 0.7 8.0 ± 0.6 7.8 ± 0.5 7.5 ± 0.5 7.0 ± 0.7 6.0 ± 0.5 5.5 ± 0.4 5.0 ± 0.5
VSWR < 1.5
Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ± 30° (dB) > 23 > 26 > 26 > 26 > 26 > 27 > 27 > 28
Penta-band
Hexa-band
Cross polar ratio (dB) 0° > 17 > 18 > 19 > 20 > 15 > 16 > 17 > 17
Max. power per input (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Total power (W) 1200 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA). 106
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2769 x 429 x 196
Packing dimensions (H x W x D) (mm) 2980 x 530 x 275
Antenna weight (kg) 46.5
Clamps weight (kg) 5.8 (2 units)
Antenna packing weight (kg) 67.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1787
2769
Accessories
Item Model Description Weight Units per antenna
225
DXXXXXX-690-960/690-960/1695-2690/1695-2690/1695-2690/1695-
2690-65/65/65/65/65/65-17i/17i/17.5i/17.5i/17.5i/17.5i-M/M/M/M/M/M-R
EasyRET Hexa-Band Antenna with Integrated RCUs - 2.6m
Model: ASI4518R10
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
HWMxxx...…RTy4
Lr1 Rr2
HWMxxx…..…Rr2
r - Red y - Yellow
L - Left array R - Right array
T - Top array B - Bottom array
226
B - 7. Multi-beam Antenna
690-960/
690-960
33(-30)/33(+30) 18.5/18.5 0-10/0-10 EasyRET2.0 4 x 7/16 DIN-F 2090 x 590 x 169 AMB4519R0 228 /
1710-2690/
1710-2690
33(-30)/33(+30) 20.5/20.5 0-10/0-10 MET2.0 4 x 7/16 DIN-F 1468 x 349 x 166 AMB452000 230 /
1710-2690/
1710-2690
33(-30)/33(+30) 20.5/20.5 0-10/0-10 EasyRET2.0 4 x 7/16 DIN-F 1468 x 349 x 166 AMB4520R0 232 /
790-960/
65/33 0-10/0-10/
1710-2200/
(-30)/33(+30)
16/20.5/20.5
0-10
EasyRET2.0 6 x 7/16 DIN-F 2022 x 359 x 178 AMB4520R1 234 /
1710-2200
690-960/
65/33 0-10/0-10/
1710-2200/
(-30)/33(+30)
17/19.5/19.5
0-10
EasyRET2.0 6 x 7/16 DIN-F 2750 x 359 x 178 **AMB4520R3 236 /
1710-2200
690-960/
1695-2690/ 0-10/0-10/
65/65/65/33 17/17.5/17.5/
Multi-beam
1695-2690/
(-30)/33(+30) 18.5/18.5
0-10/0-10/ EasyRET2.0 10 x 7/16 DIN-F 2750 x 359 x 178 **AMB4519R2 237 /
1695-2200/ 0-10
1695-2200
** Preliminary Issue
2MX-690-960-33-18.5i-M-R
EasyRET Dual-Beam Antenna with 2 Integrated RCUs - 2.0m
Model: AMB4519R0
Antenna Specifications
Electrical Properties
690 - 960
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10, continuously adjustable
at mid Tilt 16.6 18.0 18.2 18.3
Gain (dBi)
over all Tilts 16.5 ±0.5 17.8 ±0.4 18.0 ±0.3 18.2 ±0.3
Side lobe suppression for first side lobe
> 16 > 17 > 18 > 18
above main beam (dB)
Horizontal 3dB beam width (°) 39 ±3 37 ±3 36 ±2 34 ±2
Vertical 3dB beam width (°) 10.0 ±0.5 9.2 ±0.3 8.9 ±0.3 8.3 ±0.3
VSWR < 1.5
Horizontal beam centers (°) ± 30 ± 28 ± 27 ± 25
Cross polar isolation (dB) Same beam: ≥ 22 Same beam: ≥26
Front to back ratio, ±30° (dB) > 25 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 17 > 22 > 23 > 23
Max. power per input (W) 500 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
144
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 2090 x 590 x 169
Packing dimensions (H x W x D) (mm) 2350 x 705 x 275
Antenna weight (kg) 39.8
Clamps weight (kg) 5.8 (2 units)
Antenna packing weight (kg) 52.8 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
2090
1267
Accessories
Item Model Description Weight Units per antenna
228
2MX-690-960-33-18.5i-M-R
EasyRET Dual-Beam Antenna with 2 Integrated RCUs - 2.0m
Model: AMB4519R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 50 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
Multi-beam
HWMxxx…….r
HWMxxx……rr
r - Red
229
2MX-1710-2690-33-20.5i-M
Model: AMB452000
Antenna Specifications
Electrical Properties
1710 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10, continuously adjustable
at mid Tilt 19.2 19.7 20.0 20.2
Gain (dBi)
over all Tilts 19.0 ±0.6 19.5 ±0.6 19.8 ±0.5 20.0 ±0.8
Side lobe suppression for first side lobe
> 17 > 17 > 17 > 17
above main beam (dB)
Horizontal 3dB beam width (°) 34 ±2.1 31 ±2.3 29 ±0.5 27 ±1.0
Vertical 3dB beam width (°) 6.4 ±0.5 5.9 ±0.4 5.1 ±0.2 4.7 ±0.3
VSWR < 1.5
Horizontal beam centers (°) ± 30 ± 27 ± 25 ± 23
Cross polar isolation (dB) Same beam: ≥ 28
Front to back ratio, ±30° (dB) > 32 > 32 > 32 > 32
Cross polar ratio (dB) 0° > 20 > 20 > 22 > 22
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1468 x 349 x 166
Accessories
Item Model Description Weight Units per antenna
230
2MX-1710-2690-33-20.5i-M
Model: AMB452000
This antenna can upgrade to RET antenna when with a remote electrical tilt module.
AIMM20D11 Remote electrical tilt module, a couple of AISG connectors 0.6 kg 1 (Separate packing)
106
1286
1468
Multi-beam
Pattern sample for reference
231
2MX-1710-2690-33-20.5i-M-R
EasyRET Dual-Beam Antenna with 2 Integrated RCUs - 1.4m
Model: AMB4520R0
Antenna Specifications
Electrical Properties
1710 - 2690
Frequency range (MHz)
1710 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10, continuously adjustable
at mid Tilt 19.2 19.7 20.0 20.2
Gain (dBi)
over all Tilts 19.0 ±0.6 19.5 ±0.6 19.8 ±0.5 20.0 ±0.8
Side lobe suppression for first side lobe
> 17 > 17 > 17 > 17
above main beam (dB)
Horizontal 3dB beam width (°) 34 ±2.1 31 ±2.3 29 ±0.5 27 ±1.0
Vertical 3dB beam width (°) 6.4 ±0.5 5.9 ±0.4 5.1 ±0.2 4.7 ±0.3
VSWR < 1.5
Horizontal beam centers (°) ± 30 ± 27 ± 25 ± 23
Cross polar isolation (dB) Same beam: ≥ 28
Front to back ratio, ±30° (dB) > 32 > 32 > 32 > 32
Cross polar ratio (dB) 0° > 20 > 20 > 22 > 22
Max. power per input (W) 250 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
Downtilt 1 (Separate
ASMDT0C01 Mechanical downtilt: 0 - 16 ° 2.1 kg
kit packing)
232
2MX-1710-2690-33-20.5i-M-R
EasyRET Dual-Beam Antenna with 2 Integrated RCUs - 1.4m
Model: AMB4520R0
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
Multi-beam
HWMxxx…...y
HWMxxx….yy
y - Yellow
233
2MXX-790-960/1710-2200-65/33-16i/19.5i-M/M-R
EasyRET Hybrid Triple-beam Antenna with 3 Integrated RCUs - 2.0m
Model: AMB4520R1
Antenna Specifications
Electrical Properties
790 - 960 1710 - 2200
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1990 1920 - 2200
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10, continuously adjustable 0 - 10 , continuously adjustable
at mid Tilt 15.3 15.7 16.0 18.7 19.1
Gain (dBi)
over all Tilts 15.0 ±0.5 15.3 ±0.5 15.8 ±0.4 18.4 ±0.5 18.8 ±0.5
Side lobe suppression for first side lobe
> 17 > 17 > 18 > 18 > 18
above main beam (dB)
Horizontal 3dB beam width (°) 65 ±4 62 ±2.5 60 ±2.5 32 ±1 30 ±1
Vertical 3dB beam width (°) 9.8 ±0.5 9.3 ±0.5 8.5 ±0.5 6.5 ±0.3 6.0 ±0.3
VSWR < 1.5
Horizontal beam centers (°) / ± 28 ± 27
Cross polar isolation (dB) ≥ 25 Same beam: ≥ 25
Interband isolation (dB) ≥ 30 (790 - 960 // 1710 - 2200 MHz)
Front to back ratio, ±30° (dB) > 25 > 25 > 25 > 28 > 28
Cross polar ratio (dB) 0° > 17 > 17 > 17 > 18 > 15
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Accessories
Item Model Description Weight Units per antenna
Downtilt
ASMDT0D01 Mechanical downtilt: 0 - 12 ° 2.1 kg 1 (Separate packing)
kit
234
2MXX-790-960/1710-2200-65/33-16i/19.5i-M/M-R
EasyRET Hybrid Triple-beam Antenna with 3 Integrated RCUs - 2.0m
Model: AMB4520R1
Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) < 65 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: UL 60950-1 (Safety), UL 60950-22 (Safety – Equipment installed outdoor), EN 55022 (Emission),
EN 55024 (Immunity), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM
Multi-beam
HWMxxx……r
HWMxxx……b
HWMxxx…..bb
r - Red b - Blue
235
2MXX-690-960/1710-2200-65/33-17i/19.5i-M/M-R
EasyRET Hybrid Triple-beam Antenna with 3 Integrated RCUs - 2.6m
Model: AMB4520R3
Preliminary Issue
Electrical Properties
Mechanical Properties
236
2MXXXX-690-960/1695-2690/1695-2690/1695-2200-65/65/65/33-
17i/17.5i/17.5i/18.5i-M/M/M/M-R
EasyRET Hybrid Penta-beam Antenna with 5 Integrated RCUs - 2.6m
Model: AMB4519R2
Preliminary Issue
Electrical Properties
Mechanical Properties
Multi-beam
Mechanical downtilt (°) 0-8
237
B - 8. TDD Antenna
B - 9. Cluster Antenna
Cluster Antenna
Cluster
TDD
DX-2300-2690-90-16i-M-R
Model: ATD4516R5
Antenna Specifications
Electrical Properties
Frequency range (MHz) 2300 - 2400 2496 - 2690
Polarization +45° , -45°
General
Electrical downtilt (°) 2 - 12 , continuously adjustable
parameters
Electrical downtilt tolerance (°) ±1
Grounding DC Ground
240
DX-2300-2690-90-16i-M-R
Model: ATD4516R5
106
Mechanical Properties
Distance between columns (mm) 62
Antenna dimensions (H x W x D) (mm) 1445 x 299 x 109
Packing dimensions (H x W x D) (mm) 1770 x 350 x 180
Antenna weight (kg) 16.0
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 22.8 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
1331
1445
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 520 (at 150 km/h)
Wind load (N) Lateral: 105 (at 150 km/h)
Rear side: 600 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 9 x N Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Cluster
RET S/N: HWMxxx….b
TDD
RAE S/N: HWXxxx…..b
b - Blue
241
DX-2300-2690-90-16i-M-R
Model: ATD4516R5
242
DX-2300-2690-90-16i-M-R
Model: ATD4516R5
RET Properties
RET type Integrated RET
RET protocols AISG 2.0 / 3GPP
Input voltage range (V) DC 10 - 30
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) Typ. < 55
RET interface 1 (RF feeder) Calibration channel integrate the Bias-T and supporting OOK modulation signal communication
2 x 8 pin connector according to IEC 60130-9
RET interface 2 (485 connector)
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Lightning protection (kA) 10 (8/20 μs)
RAE Properties
RAE type Integrated RAE, manages antenna information
RAE protocols AISG-ES-RAE V2.1.0
EasyBeam Properties
Frequency range (MHz) 2300 - 2400 2496 - 2690
Electrical downtilt (°) 2 - 12
Horizontal 3dB beam
30 65 90 30 65 90
width (°)
Broadcast
Electrical azimuth (°) -15..+15 0 -15..+15 0
beam
Electrical azimuth
1 / 1 /
step(°)
Cluster
Certification: CE, FCC, IC
TDD
243
DX-3400-3800-90-15.5i-M-R
Model: ATD4516R7
Preliminary Issue
Electrical Properties
Frequency range (MHz) 3400 - 3800
Polarization +45° , -45°
General
Electrical downtilt (°) 2 – 12, continuously adjustable
parameters
Electrical downtilt tolerance (°) ±1
Grounding DC Ground
Coupling factor between calibration port and each
-26
antenna port (dB)
Max. amplitude tolerance from calibration port to
0.9
input ports (dB)
Max. phase tolerance from calibration port to input
Calibration 7
ports (°)
and electrical
parameters Ports VSWR 1.5
244
DX-3400-3800-90-15.5i-M-R
Model: ATD4516R7
Mechanical Properties
Distance between columns (mm) 43
Antenna dimensions (H x W x D) (mm) 990 x 269 x 86
Packing dimensions (H x W x D) (mm) 1150 x 340 x 155
Antenna weight (kg) 13
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 19.4 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 385 (at 150 km/h)
Wind load (N) Lateral: 55 (at 150 km/h)
Rear side: 370 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 9 x N Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
Cluster
TDD
245
DX-3400-3800-90-15.5i-M-R
Model: ATD4516R7
RET Properties
RET type Integrated RET
RET protocols AISG 2.0 / 3GPP
Input voltage range (V) DC 10 - 30
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) Typ. < 55
RET interface 1 (RF feeder) Calibration channel integrate the Bias-T and supporting OOK modulation signal communication
2 x 8 pin connector according to IEC 60130-9
RET interface 2 (485 connector)
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
RAE Properties
RAE type Integrated RAE, manages antenna information
RAE protocols AISG-ES-RAE V2.1.0
Standards: EN 60950-1 (Safety), UL 60950-22(Safety – Equipment installed outdoor), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN
301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
246
DX-3300-3800-65-17i-M-R
Model: ATD4517R0
Preliminary Issue
Electrical Properties
Frequency range (MHz) 3300 - 3800
Polarization +45° , -45°
General
Electrical downtilt (°) 2 – 12, continuously adjustable
parameters
Electrical downtilt tolerance (°) ±1
Grounding DC Ground
Coupling factor between calibration port and
-26
each antenna port (dB)
Max. amplitude tolerance from calibration port to
0.9
input ports (dB)
Mechanical Properties
Cluster
Antenna dimensions (H x W x D) (mm) 990 x 323 x 89
TDD
Packing dimensions (H x W x D) (mm) 1310 x 390 x 155
Antenna net weight (kg) 15
Bracket weight (kg) 4.2
Packing weight (kg) 22.5
Mechanical downtilt (°) 0 - 16
Mast diameter (mm) 50 - 115
Operational temperature (℃) -40 .. +65
Frontal: 420 (at 150 km/h)
Wind load (N) Lateral: 75 (at 150 km/h)
Rear side: 470 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 9 x N Female
Connector position Bottom
247
DX-3300-3800-65-17i-M-R
Model: ATD4517R0
RET Properties
RET type Integrated RET
RET protocols AISG 2.0 / 3GPP
Input voltage range (V) DC 10 - 30
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) Typ. < 55
RET interface 1 (RF feeder) Calibration channel integrate the Bias-T and supporting OOK modulation signal communication
2 x 8 pin connector according to IEC 60130-9
RET interface 2 (485 connector)
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
RAE Properties
RAE type Integrated RAE, manages antenna information
RAE protocols AISG-ES-RAE V2.1.0
Standards: EN 60950-1 (Safety), UL 60950-22(Safety – Equipment installed outdoor), EN 55022 (Emission), EN 55024 (Immunity), ETSI EN
301 489, FCC part15
Certification: CE, FCC, RoHS, WEEE
248
CX-1710-2690-65-18i-M
Model: A264518S0
Antenna Specifications
Vertical 3dB beam width (°) 6.7 ±0.4 6.1 ±0.5 5.5 ±0.3 4.9 ±0.2
Max. power per input (W) 250 (at 50℃ ambient temperature)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x D) (mm) 1793 x Φ 230 and Φ 250
Cluster
TDD
Packing dimensions (H x W x D) (mm) 2000 x 390 x 385
Antenna net weight (kg) 22.5
Packing weight (kg) 29.8
Φ 230
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Wind load (N) 310 (at 150 km/h)
1793
1443
service area
SBT ASBT00001 (cover attached)
249
CX-1710-2690-65-18i-M
Model: A264518S0
57 55
59
+45° -45°
1710 - 2690
7/16 (F)
7/16 (F)
-45° +45°
Unit: mm
250
C. Antenna Information Management
C - 1. RET System
C - 1 - 1. Remote Control Unit (RCU)
Intelligent
Input voltage RET
AISG type Protection class Mounting type Dimension (mm) Model Page
range (V)
Wall mounting //
DC 10 - 30 AISG 2.0 IP65
Mast mounting
174 x 150 x 48.5 AREU01301 262
Frequency Range
AISG type Insertion loss (dB) Dimension (mm) Model Page
(MHz)
Frequency Range
AISG type Insertion loss (dB) Dimension (mm) Model Page
(MHz)
AISG Connecting Cables For Remote Electrical Tilt (RET) System 270
AISG Connecting Cables For Huawei RRU RET_Port 271
C - 2. Intelligent Management
C - 2 - 1. Antenna Information Sensor Unit (AISU)
Input voltage
AISG type Protection class Dimension (mm) Model Page
range (V)
A19451703
ARCU02001
A19452101
A79451500v01
A79451600v02
A79451700v02
A79451702
A19451505
A19451902
A26451500
ADU451503
ADU451602v01
ADU451807v01
ADU4517C0
ADU4518C1 ARCU02004
ADU4518C0
ADU451720
ADU451902
ADU451507
Intelligent
ATR451602v01
ATR451715 RET
ATR451704v01
ATR451709
ATR451606
ATR451607
A264518S0
Antenna Model
*AIMM
EasyRET2.0 (Antenna information management module)
MET2.0
(Corresponding to MET2.0)
A79451503 A794515R1
A26451800v02 A264518R0v01
ADU451716v01 ADU4518R10
ADU451604v01 ADU4518R11
ADU451712v01 ADU4518R12
AIMM20D11
ADU451819v01 ADU4518R1v01
ADU451816v02 ADU4518R6v01
AMB452000 AMB4520R0
ATR451806 ATR4518R13
ATR451714v01 ATR4518R14
RCU (Remote Control Unit) drives the phase shifter in antenna through mechanical interface to
change the electrical downtilt. RCU is suitable for daisy chain solution. RCU is used for MET1.0
antennas upgrading to RET antennas.
Input voltage range (V) DC 10 - 30
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Housing material Profile: Aluminium coated // Cover: Aluminium die cast coated
Color Grey
Weight (g) 600
Operating temperature range (℃) -40 … +65
Protection class IP24
Dimensions (L x W x H) (mm) 200 x 56 x 47
Packing size (L x W x H) (mm) 268 x 105 x 95
Drainage Drainage
Hole Hole
Intelligent
RET
Appearance Bottom view of RCU Male Female
Please note: Before the installation, check whether the RCU and base station support the same AISG protocol. If not,
contact the technical support personnel of Huawei.
255
RCU
Model: ARCU02004 (AISG 2.0)
RCU (Remote Control Unit) drives the phase shifter in antenna through mechanical interface to
change the electrical downtilt. RCU is suitable for daisy chain solution. RCU is used for MET1.0
antennas upgrading to RET antennas.
Input voltage range (V) DC 10 - 30
< 10 (motor activated)
Power consumption (W)
< 0.5 (stand by)
Adjustment time (full range) (min) < 1.5 (typically, depending on antenna type)
Calibration time (min) < 3 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
Connectors
Daisy chain in: Male // Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Housing material Profile: Aluminium coated // Cover: Aluminium die cast coated
Color RAL 7035
Weight (g) 600
Operating temperature range (℃) -40 … +65
Protection class IP24
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
Dimensions (L x W x H) (mm) 180 x 65 x 54
Packing size (L x W x H) (mm) 268 x 105 x 95
Drainage
Hole
256
Single-band Antenna Information Management Module with a Pair of
AISG Connectors (1in1out)
Model: AIMM20S11
The antenna information management module (AIMM) supports remote electrical tilt (RET) function
and manages antenna information. AIMM20S11 is used for MET2.0 single-band antennas upgrading
to RET antennas.
Protocol AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) Typ. < 50
2 x 8 pin connector according to IEC 60130-9
Connectors
Daisy chain in: Male // Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Operating temperature range (℃) -40 … +85
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
Weight (g) 380
Packing Weight (g) 450
Dimensions (L x W x H) (mm) 197 x 82 x 30
Packing size (L x W x H) (mm) 250 x 118 x 40
Standards: UL 60950-1(Safety))
UL 60950-22(Safety – Equipment
Please note:
installed outdoor)
Before the installation, check whether the AIMM and
EN 55022(Emission)
base station support the same AISG protocol. If not,
EN 55024(Immunity) contact the technical support personnel of Huawei.
ETSI EN 301 489
FCC Part 15
ICES-003
Certification: CE、FCC、IC、RCM
Intelligent
RET
257
Dual-band Antenna Information Management Module with a Pair of
AISG Connectors (1in1out)
Model: AIMM20D11
The antenna information management module (AIMM) supports remote electrical tilt (RET) function
and manages antenna information. AIMM20D11 is used for MET2.0 dual-band antennas upgrading
to RET antennas.
Protocol AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 5 (motor activated, 12V)
Power consumption (W)
< 0.5 (stand by, 12V)
Adjustment time (full range) (s) Typ. < 50
2 x 8 pin connector according to IEC 60130-9
Connectors
Daisy chain in: Male // Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Operating temperature range (℃) -40 … +85
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
Weight (g) 520
Packing weight (g) 600
Dimensions (L x W x H) (mm) 203 x 107 x 29
Packing size (L x W x H) (mm) 250 x 118 x 40
Standards: UL 60950-1(Safety))
UL 60950-22(Safety – Equipment
Please note:
installed outdoor)
Before the installation, check whether the AIMM and
EN 55022(Emission)
base station support the same AISG protocol. If not,
EN 55024(Immunity) contact the technical support personnel of Huawei.
ETSI EN 301 489
FCC Part 15
ICES-003
Certification: CE、FCC、IC、RCM
258
Dual-band Antenna Information Management Module with Two Pairs
of AISG Connectors (2in2out)
Model: AIMM20D22
The antenna information management module (AIMM) supports remote electrical tilt (RET) function
and manages antenna information.
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
Standards: UL 60950-1(Safety))
UL 60950-22(Safety – Equipment
Please note:
installed outdoor)
Before the installation, check whether the AIMM and
EN 55022(Emission)
base station support the same AISG protocol. If not,
EN 55024(Immunity) contact the technical support personnel of Huawei.
ETSI EN 301 489
FCC Part 15
ICES-003
Intelligent
RET
Certification: CE、FCC、IC、RCM
259
Multi-band Antenna Information Management Module with a Pair of
AISG Connectors (1in1out)
Model: AIMM20M11
The antenna information management module (AIMM) supports remote electrical tilt (RET) function
and manages antenna information. AIMM20M11 is used for MET2.0 tri-band antennas upgrading to
RET antennas.
Protocol AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) Typ. < 65
2 x 8 pin connector according to IEC 60130-9
Connectors
Daisy chain in: Male // Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Operating temperature range (℃) -40 … +85
3 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
Weight (g) 700
Packing weight (g) 800
Dimensions (L x W x H) (mm) 203 x 153 x 30
Packing size (L x W x H) (mm) 245 x 163 x 37
Standards: UL 60950-1(Safety))
UL 60950-22(Safety – Equipment
Please note:
installed outdoor)
Before the installation, check whether the AIMM and
EN 55022(Emission)
base station support the same AISG protocol. If not,
EN 55024(Immunity) contact the technical support personnel of Huawei.
ETSI EN 301 489
FCC Part 15
ICES-003
Certification: CE、FCC、IC、RCM
260
Multi-band Antenna Information Management Module with Two Pairs
of AISG Connectors (2in2out)
Model: AIMM20M22
The antenna information management module (AIMM) supports remote electrical tilt (RET) function
and manages antenna information.
Standards: UL 60950-1(Safety))
UL 60950-22(Safety – Equipment
Please note:
installed outdoor)
Before the installation, check whether the AIMM and
EN 55022(Emission)
base station support the same AISG protocol. If not,
EN 55024(Immunity) contact the technical support personnel of Huawei.
ETSI EN 301 489
FCC Part 15
ICES-003
Intelligent
Certification: CE、FCC、IC、RCM
RET
Daisy chain out: Female
261
REU-3way
Model: AREU01301
The RET Expansion Unit (REU) is a multi-port AISG signal management device that enables multiple
main devices to manage an AISG link.
Please note: The REU can work with a main device supporting AISG1.1 or AISG2.0. However, if the REU software needs to be upgraded,
the main device must support AISG2.0.
Male Female
262
REU-3way
Model: AREU01301
Unit: mm
ANTENNA
1 2 3
Intelligent
RET
REU
NOTE
When installing the REU ground cable, a copper-core cable with a cross-sectional area of 6 mm² is recommended.
There are REU and hoop iron in the package, but not any ground cable, AISG cable or screws, and these need to be purchased
additionally depending on the detail scenarios.
263
SBT-690-2700-001 Model: ASBT00001
Features
BT = Bias Tee
BTS = Base Transceiver Station ASBT00001 ASBT00002
OOK = On Off Keying
Block Diagram
Antenna
RCU
ASBT00001 SBT
Feeder Cable
Feeder Cable
ASBT00002
SBT
CCU BTS
264
SBT-690-2700-001 Model: ASBT00001
Port 1 (Connector type) Antenna (7-16 DIN Male) BTS (7-16 DIN Male)
Port 2 (Connector type) Feeder (7-16 DIN Female) Feeder (7-16 DIN Female)
Port AISG (Connector type) AISG (8-pin Connecter Female) AISG (8-pin Connecter Male)
Electrical Properties
Port 1 ←→ Port 2
Isolation for DC signal (dB) ≥ 70
Port 1 ←→ Port AISG
Port 1 and Port 2 Avg. ≥ 500 (690 - 960 MHz) // Avg. ≥ 250 (1710 - 2690 MHz)
Input power (W)
Port AISG < 2.5 A (+8 … +30 V DC)
RF impedance (Ω) 50
Environmental Specification
Intelligent
Operating temperature (℃) -40 … +70
IP rating IP67
Mechanical Specification
265
SBT-690-2700-001 Model: ASBT00001
ASBT00001
ASBT00002
Unit: mm
266
BT-690-2700-001
Model: ABT000001
Features
BT = Bias Tee
BTS = Base Transceiver Station
OOK = On Off Keying
Block Diagram
Port 2 (ANT)
DC/OOK RF
Block
Intelligent
DC RET
Block
Port 1 (BTS)
267
BT-690-2700-001
Model: ABT000001
Electrical Properties
Port 1 ←→ Port 2
Isolation for DC signal (dB) ≥ 70
Port 1 ←→ Port DC/OOK
RF Impedance (Ω) 50
Environmental Specification
IP rating IP66
Mechanical Specification
268
BT-690-2700-001
Model: ABT000001
Unit: mm
Intelligent
RET
269
AISG Connecting Cables
Technical Specification
2 x 8 pin connector according to IEC 60130-9
Connectors
Female / Male
Cable 2 x 0.25 mm2 + 4 x 0.75 mm2 cable according to UL2464
Rate current 4A
Protection Class IP67 (Coupled)
Temperature Range -40 ~ 80 ℃
Color Black
Single Bend radius 60 mm Min.
Multiple Bend radius 120 mm Min.
Application scene Indoor // Outdoor
Cable series
Length BOM Code
0.5 m 04045920
2m 04045921
5m 04050228
10 m 04050184
15 m 04045922
30 m 04050230
50 m 04050231
60 m 04050182
70 m 04050232
270
AISG Connecting Cables
Technical Specification
8 pin connector according to IEC 60130-9
Connector 1 (to be connected to RET module)
Female
9 pin DB9 connector, water-proofed
Connector 2 (to be connected to Huawei RRU “RET_port”)
Male
Cable 4 Pair x 24 AWG
Rate current 4A
Protection Class IP67 (when coupled on RRU and RET)
Temperature Range -40 ~ 80 ℃
Color Black
Single Bend radius 60 mm Min.
Multiple Bend radius 120 mm Min.
Application scene Indoor or Outdoor
Signal
Pin Number
Female Male
1 +12 V DC nominal +12 V DC nominal Female Male
2 N/C N/C
3 RS485 B RS485 B
4 RS485 GND RS485 GND
5 RS485 A RS485 A
6 +12 V DC nominal N/C
7 DC Return N/C
8 N/C N/C
9 / DC Return
Cable series
Intelligent
RET
Length BOM Code
3m 04070193
5m 04070097
271
PAA
Model: APAA00001
The portable AISG adapter (PAA) is used for AISG devices to perform
management and control onsite. The PAA works with Bluetooth
enabled smart terminals, could support mutil-AISG-standard with
smart terminals software, with software upgrade new standard can
support. The PAA is light-weighted and easy to carry and operate,
which are suitable for site installation and maintenance. It can also be
used for systematic management during site deployment, and provide
functions such as fault location and data recording.
Specifications
Net weight (kg) 0.52 (with a built-in rechargeable battery, and without a power adapter)
Certificate: CE, FCC, IC, VCCI, RCM, TELEC, REACH, RoSH, WEEE
Standards: EN60950-1, EN55022, EN55024, VCCI V-3
272
PAA
Model: APAA00001
PAA Appearance
AISG connection port
Power supply indicator OOK connection port
Communication indicator Strap hole
Alarm indicator
Power button
Description Function
1 x 8 core female connector, complying with the IEC 60130-9 standards
AISG connection port
Connects the PAA to an ALD using an AISG cable.
OOK connection port Connects the PAA to an ALD using an RF cable.
Power indicator (PWR) Indicates the power supply status.
Communication indicator (COM) Indicates the status of communication between the PAA and smartphone.
Alarm indicator (ALM) Indicates the PAA alarms status.
Power button Used to power on or off the PAA. The PAA can be powered on or off by holding down this button.
Mini USB port Reserved for further development and is not used temporarily.
Connects to the AC/DC adapter. When an AC/DC adapter is connected, the PAA automatically uses
12 V DC adapter port
the input power supply as the operating power supply to charge the integrated battery.
Intelligent
RET
273
Antenna Information Sensor Unit
Model: AISU00001
Preliminary Issue
The Antenna Information Sensor Unit(AISU) is one device that can make antenna engineering parameters measurement
which include azimuth, machine tilt, longitude, latitude and altitude. It is installed on the antenna top to perform GPS-based
direction measurement. The AISU, base station, and network management system (NMS) compose the Self-Aware Antenna
solution, in which the antenna engineering parameters can be remotely queried on the NMS in real time.
* Depends on multipath environment, number of satellites in view, satellite geometry, ionospheric activity use of SBAS and survey timing.
** Normal temperature.
AISU
274
Antenna Information Sensor Unit
Model: AISU00001
Preliminary Issue
325
37
26
20
109
Unit: mm
Antenna
AISG cable
Antenna Antenna
Intelligent
RET
EasyRET
RCU
275
D. Antenna Line Product
D - 1. TMA
Description Frequency Range (MHz) AISG type Gain (dB) Dimension (mm) Model Page
RX : 703-748MHz 12 ±1 (Fixed )
700M
TX : 758-803MHz
AISG 2.0
8 - 16 (Adjustable)
215 x 290 x 130 ATA702000 278
RX : 832-862MHz 12 ±1 (Fixed )
DD800M
TX : 791-821MHz
AISG 2.0
8 - 16 (Adjustable)
190 x 240 x 120 ATA802000 281
RX : 880-905MHz 12 ±1 (Fixed )
E900M SUBBAND
TX : 925-950MHz
AISG 2.0
8 - 16 (Adjustable)
198 x 308 x 70.5 ATA902002 284
RX : 880-915MHz 12 ±1 (Fixed )
E900M
TX : 925-960MHz
AISG 2.0
8 - 16 (Adjustable)
248 x 324 x 75.5 ATA902001 287
RX : 1920-1980MHz 12 ±1 (Fixed )
2100M
TX : 2110-2170MHz
AISG 2.0
8 - 12 (Adjustable)
160 x 205 x 54.5 ATA212001 296
RX : 2500-2570MHz 12 ±1 (Fixed )
2600M
TX : 2620-2690MHz
AISG 2.0
8 - 12 (Adjustable)
160 x 210 x 54.5 ATA262000 299
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
Modem
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
278
DTMA-700-12dB-2eNodeBport2ANTport-AISG/CWA
Model: ATA702000
Tx Specifications
Frequency range (MHz) 758 - 803
Bandwidth (MHz) 45
Insertion loss* (dB) Avg. < 0.45
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -117 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 703 - 748
Bandwidth (MHz) 45
≥ 18 (DC ON)
Return loss(dB)
≥ 13 (DC OFF)
Insertion loss in by-pass mode (dB) ≤ 3.5 (DC OFF)
12 ±1 (Fixed )
Gain*** (dB)
8 - 16 (Adjustable)
Noise figure** (dB) Avg. < 1.5 (12 dB Gain, +22 ... +28 ℃)
Output 1dB compression (dBm) ≥ 8 (12 dB Gain)
OIP3 (dBm) ≥ 20 (12 dB Gain)
Electrical Specifications
CWA Mode (Single port) AISG Mode (Total ports)
DC supply voltage (V) 8.5 - 15 9 - 30
@12 V 99 ±5 187 ±5
Operating current per TMA (mA)
@17 V 74 ±5 134 ±5
(without RET)
@30 V / 90 ±5
Alarm management (mA) 150 - 280 AISG
Power consumption (W) < 3.5
Environmental Specification
Operating temperature range (℃) -40 ... +65
IP rating IP67
MTBF (hours) > 1,000,000
EMC ETS 300 342-3
Lightning protection (kA) 10 (8/20 us)
Mechanical Specification
DTMA dimensions (W x H x D) (mm) 215 x 290 x 130 (without connectors, without brackets)
Packing dimensions (W x H x D) (mm) 290 x 500 x 265
DTMA weight (kg) ≤ 8.5 (with brackets)
Packing weight (kg) ≤ 9.5
TMA
*Insertion loss: IL
IL758MHz 2 IL780.5MHz IL803MHz ***Noise figure: NF
NF703MHz 2 NF725.5MHz NF748MHz
4 4
**TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x40, the gain is
adjustable, and the range is from 8 dB to16 dB, and when the value is 0xFE, the gain is fixed 12 dB.
279
DTMA-700-12dB-2eNodeBport2ANTport-AISG/CWA
Model: ATA702000
Unit : mm
280
DTMA-800-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA802000
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
TMA
Modem
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
281
DTMA-800-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA802000
Tx Specifications
Frequency range (MHz) 791 - 821
Bandwidth (MHz) 30
Insertion loss* (dB) Avg. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -117 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 832 - 862
Bandwidth (MHz) 30
***TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x40, the gain is adjustable, and the
range is from 8 dB to 16 dB, and when the value is 0xFE, the gain is fixed 12 dB.
282
DTMA-800-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA802000
Unit : mm
TMA
283
DTMA-E900SUBBAND-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902002
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
Modem
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
284
DTMA-E900SUBBAND-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902002
Tx Specifications
Frequency range (MHz) 925 - 950
Bandwidth (MHz) 25
Insertion loss* (dB) Avg. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -117 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 880 - 905
Bandwidth (MHz) 25
***TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x40, the gain is
adjustable, and the range is from 8 dB to 16 dB, and when the value is 0xFE, the gain is fixed 12 dB.
285
DTMA-E900SUBBAND-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902002
Unit : mm
286
DTMA-E900-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902001
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
Modem
TMA
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
287
DTMA-E900-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902001
Tx Specifications
Frequency range (MHz) 925 - 960
Bandwidth (MHz) 35
Insertion loss* (dB) Avg. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -117 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 880 - 915
Bandwidth (MHz) 35
**TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x40, the gain is
adjustable, and the range is from 8 dB to 16 dB, and when the value is 0xFE, the gain is fixed 12 dB.
288
DTMA-E900-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902001
Unit : mm
TMA
289
DTMA-P900-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902003
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
Modem
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
290
DTMA-P900-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902003
Tx Specifications
Frequency range (MHz) 935 - 960
Bandwidth (MHz) 25
Insertion loss* (dB) Avg. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -117 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 890 - 915
Bandwidth (MHz) 25
***TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x40, the gain is
adjustable, and the range is from 8 dB to 16 dB, and when the value is 0xFE, the gain is fixed 12 dB.
291
DTMA-P900-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA902003
Unit : mm
292
DTMA-1800-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA182001
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
TMA
Modem
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
293
DTMA-1800-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA182001
Tx Specifications
Frequency range (MHz) 1805 - 1880
Bandwidth (MHz) 75
Insertion loss* (dB) Avg. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -117 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 1710 - 1785
Bandwidth (MHz) 75
***TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x30, the gain is
adjustable, and the range is from 8 dB to12 dB, and when the value is 0xFE, the gain is fixed 12 dB.
294
DTMA-1800-12dB-2BTSport2ANTport-AISG/CWA
Model: ATA182001
Unit : mm
TMA
295
DTMA-2100-12dB-2NodeBport2ANTport-AISG/CWA
Model: ATA212001
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
Modem
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
296
DTMA-2100-12dB-2NodeBport2ANTport-AISG/CWA
Model: ATA212001
Tx Specifications
Frequency range (MHz) 2110 - 2170
Bandwidth (MHz) 60
Insertion loss* (dB) Avg. < 0.25
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -122 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 1920 - 1980
Bandwidth (MHz) 60
***TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x30, the gain is
adjustable, and the range is from 8 dB to 12 dB, and when the value is 0xFE, the gain is fixed 12 dB.
297
DTMA-2100-12dB-2NodeBport2ANTport-AISG/CWA
Model: ATA212001
Unit : mm
298
DTMA-2600-12dB-2eNodeBport2ANTport-AISG/CWA
Model: ATA262000
Product Description
The dual tower mounted amplifier (DTMA) is a low-noise amplifier installed near the antenna. It helps to
improve the signal-to-noise ratio and enhance the receiving sensitivity of the BTS system. It enhances the
uplink coverage and reduces uplink and downlink imbalance of the base station. It effectively reduces the
transmitting power used by cellphones and improves voice and data communication quality.
Features
ANT 0 ANT 1
Lightning Lightning
protection protection
LNA LNA
Control
Circuit
&
Modem
TMA
RS485
Bias Tee & DC & OOK DC & OOK Bias Tee &
Lightning protection Lightning protection
299
DTMA-2600-12dB-2eNodeBport2ANTport-AISG/CWA
Model: ATA262000
Tx Specifications
Frequency range (MHz) 2620 - 2690
Bandwidth (MHz) 70
Insertion loss* (dB) Avg. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -117 (2 TX carriers at +43 dBm)
Rx Specifications
Frequency range (MHz) 2500 - 2570
Bandwidth (MHz) 70
***TMA gain can be switched from fixed to adjustable via the gain setting command. when set a value between 0x20 and 0x30, the gain is
adjustable, and the range is from 8 dB to 12 dB, and when the value is 0xFE, the gain is fixed 12 dB.
300
DTMA-2600-12dB-2eNodeBport2ANTport-AISG/CWA
Model: ATA262000
Unit : mm
TMA
301
MTMA-1800/2100-12dB-2BTSport2ANTport-AISG
Model: ATADU2002
Product Description
The multiband tower mounted amplifier (MTMA) is a low-noise amplifier installed near the antenna to
satisfy the co-siting purposes. It helps to improve the signal-to-noise ratio and enhance the receiving
sensitivity of the BTS system. It enhances the uplink coverage and reduces uplink and downlink imbalance
of the base station. It effectively reduces the transmitting power used by cellphones and improves voice
and data communication quality. When scanning the AISG ALD, the MTMA can be operated from one
primary controller, either on BTS0 or BTS1 port. When scanning the AISG ALD, the TMA is responding to
the AISG controller with two individual serial numbers (unique IDs) with each their two subunits (two
subunits per frequency band).
Features
302
MTMA-1800/2100-12dB-2BTSport2ANTport-AISG
Model: ATADU2002
Tx Specifications
Frequency range (MHz) 1805 - 1880 2110 - 2170
Bandwidth (MHz) 75 60
Insertion loss (dB) Typ. < 0.45 Typ. < 0.35
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -110 (3rd order; with 2 x 43 dBm) ≤ -122 (7th order; with 2 x 43 dBm)
Rx Specifications
Frequency range (MHz) 1710 - 1785 1920 - 1980
Bandwidth (MHz) 75 60
≥ 18 (DC ON)
Return loss (dB)
≥ 14 (DC OFF)
Insertion loss in by-pass mode (dB) Typ. < 3.0
Gain (dB) 12 ±1
Noise figure (dB) Typ. < 1.2 Typ. < 1.2
Output 1dB compression (dBm) ≥ 12
OIP3 (dBm) ≥ 24
Electrical Specifications
DC supply voltage (V) 9 - 30
@12 V 245 ±5
Operating current per TMA (mA)
@17 V 175 ±5
(without RET)
@30 V 105 ±5
Alarm management AISG
Power consumption (W) < 3.0
Environmental Specification
Operating temperature range (℃) -40 ... +65
IP rating IP67
MTBF (hours) > 1,000,000
EMC ETS 300 342-3
Lightning protection (kA) 10 (8/20 us)
Mechanical Specification
196 x 280 x 110
MTMA dimensions (W x H x D) (mm)
(without connectors, without brackets)
TMA
303
MTMA-1800/2100-12dB-2BTSport2ANTport-AISG
Model: ATADU2002
Unit : mm
304
MTMA-1800/2100-12dB-2BTSport4ANTport-AISG
Model: ATADU2003
Product Description
The multiband tower mounted amplifier (MTMA) is a low-noise amplifier installed near the antenna to
satisfy the co-siting purposes. It helps to improve the signal-to-noise ratio and enhance the receiving
sensitivity of the BTS system. It enhances the uplink coverage and reduces uplink and downlink imbalance
of the base station. It effectively reduces the transmitting power used by cellphones and improves voice
and data communication quality. When scanning the AISG ALD, the TMA is responding to the AISG
controller with two individual serial numbers (unique IDs) with each their two subunits (two subunits per
frequency band).
Features
TMA
305
MTMA-1800/2100-12dB-2BTSport4ANTport-AISG
Model: ATADU2003
Tx Specifications
Frequency range (MHz) 1805 - 1880 2110 - 2170
Bandwidth (MHz) 75 60
Insertion loss (dB) Typ. < 0.45 Typ. < 0.35
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -110 (3rd order; with 2 x 43 dBm) ≤ -122 (7th order; with 2 x 43 dBm)
Rx Specifications
Frequency range (MHz) 1710 - 1785 1920 - 1980
Bandwidth (MHz) 75 60
≥ 18 (DC ON)
Return loss (dB)
≥ 14 (DC OFF)
Insertion loss in by-pass mode (dB) Typ. < 3.0
Gain (dB) 12 ±1
Noise figure (dB) Typ. < 1.2 Typ. < 1.2
Output 1dB compression (dBm) ≥ 12
OIP3 (dBm) ≥ 24
Electrical Specifications
DC supply voltage (V) 9 - 30
@12 V 225 ±5
Operating current per TMA (mA)
@17 V 165 ±5
(without RET)
@30 V 105 ±5
Environmental Specification
Operating temperature range (℃) -40 ... +65
IP rating IP67
MTBF (hours) > 1,000,000
EMC ETS 300 342-3
Lightning protection (kA) 10 (8/20 us)
Mechanical Specification
196 x 280 x 110
MTMA dimensions (W x H x D) (mm)
(without connectors, without brackets)
Packing dimensions (W x H x D) (mm) 245 x 475 x 220
MTMA weight (kg) ≤ 7.3 (with brackets)
Packing weight (kg) ≤ 8.5
MTMA Volume (L) Approx. 5.9
8-pin female, IEC 60130-9 (pin6: 8.5V - 30V DC, pin3: RS485B, pin5: RS485A, pin7:
AISG connector
DC return, other pins: not connected)
Wall mounting: with 4 screws (max. 8 mm diameter)
Mounting
Mast mounting
Mast diameter (mm) Default: 30 - 125 // Optional: 40 - 140
Connector 6 x 7/16 DIN Female ( Two ports are BTS and four ports are ANT)
306
MTMA-1800/2100-12dB-2BTSport4ANTport-AISG
Model: ATADU2003
Unit : mm
TMA
307
MTMA-800/E900-12dB-2eNodeBport2ANTport-AISG
Model: ATADU2001
Product Description
The multiband tower mounted amplifier (MTMA) is a low-noise amplifier installed near the antenna to
satisfy the co-siting purposes. It helps to improve the signal-to-noise ratio and enhance the receiving
sensitivity of the BTS system. It enhances the uplink coverage and reduces uplink and downlink imbalance
of the base station. It effectively reduces the transmitting power used by cellphones and improves voice
and data communication quality. When scanning the AISG ALD, the MTMA can be operated from one
primary controller, either on NodeB0 or NodeB1 port. When scanning the AISG ALD, the TMA is
responding to the AISG controller with two individual serial numbers (unique IDs) with each their two
subunits (two subunits per frequency band).
Features
308
MTMA-800/E900-12dB-2eNodeBport2ANTport-AISG
Model: ATADU2001
Tx Specifications
Frequency range (MHz) 791 - 821 925 - 960
Bandwidth (MHz) 30 35
Insertion loss (dB) Typ. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -110 (3rd order; with 2 x 43 dBm)
Rx Specifications
Frequency range (MHz) 832 - 862 880 - 915
Bandwidth (MHz) 30 35
≥ 18 (DC ON)
Return loss(dB)
≥ 14 (DC OFF)
Insertion loss in by-pass mode (dB) Typ. < 3.0
Gain (dB) 12 ±1
Noise figure (dB) Typ. < 1.3
Output 1dB compression (dBm) ≥ 12
OIP3 (dBm) ≥ 24
Electrical Specifications
DC supply voltage (V) 9 - 30
@12 V 245 ±5
Operating current per TMA (mA)
@17 V 175 ±5
(without RET)
@30 V 105 ±5
Alarm management AISG
Power consumption (W) < 3.0
Environmental Specification
Operating temperature range (℃) -40 ... +65
IP rating IP67
MTBF (hours) > 1,000,000
EMC ETS 300 342-3
Lightning protection (kA) 10 (8/20 us)
Mechanical Specification
247 x 342 x 132
MTMA dimensions (W x H x D) (mm)
(without connectors, without brackets)
TMA
309
MTMA-800/E900-12dB-2eNodeBport2ANTport-AISG
Model: ATADU2001
Unit : mm
310
MTMA-800/E900-12dB-2eNodeBport4ANTport-AISG
Model: ATADU2005
Product Description
The multiband tower mounted amplifier (MTMA) is a low-noise amplifier installed near the antenna to
satisfy the co-siting purposes. It helps to improve the signal-to-noise ratio and enhance the receiving
sensitivity of the BTS system. It enhances the uplink coverage and reduces uplink and downlink imbalance
of the base station. It effectively reduces the transmitting power used by cellphones and improves voice
and data communication quality. When scanning the AISG ALD, the TMA is responding to the AISG
controller with two individual serial numbers (unique IDs) with each their two subunits (two subunits per
frequency band).
Features
TMA
311
MTMA-800/E900-12dB-2eNodeBport4ANTport-AISG
Model: ATADU2005
Tx Specifications
Frequency range (MHz) 791 - 821 925 - 960
Bandwidth (MHz) 30 35
Insertion loss (dB) Typ. < 0.4
Return loss (dB) ≥ 18
< 160 (+52 dBm) CW
Input power (W)
< 2000 (+63 dBm) peak
Intermodulation products in Rx band (dBm) ≤ -110 (3rd order; with 2 x 43 dBm)
Rx Specifications
Frequency range (MHz) 832 - 862 880 - 915
Bandwidth (MHz) 30 35
≥ 18 (DC ON)
Return loss(dB)
≥ 14 (DC OFF)
Insertion loss in by-pass mode (dB) Typ. < 3.0
Gain (dB) 12 ±1
Noise figure (dB) Typ. < 1.3
Output 1dB compression (dBm) ≥ 12
OIP3 (dBm) ≥ 24
Electrical Specifications
DC supply voltage (V) 9 - 30
@12 V 225 ±5
Operating current per TMA (mA)
@17 V 165 ±5
(without RET)
@30 V 105 ±5
Alarm management AISG
Power consumption (W) < 3.0
Environmental Specification
Operating temperature range (℃) -40 ... +65
IP rating IP67
MTBF (hours) > 1,000,000
EMC ETS 300 342-3
Lightning protection (kA) 10 (8/20 us)
Mechanical Specification
247 x 342 x 132
MTMA dimensions (W x H x D) (mm)
(without connectors, without brackets)
Packing dimensions (W x H x D) (mm) 300 x 545 x 250
MTMA weight (kg) ≤ 10.5 (with brackets)
Packing weight (kg) ≤ 12.3
MTMA Volume (L) Approx. 10.8
8-pin female, IEC 60130-9 (pin6: 8.5V - 30V DC, pin3: RS485B, pin5: RS485A, pin7:
AISG connector
DC return, other pins: not connected)
Wall mounting: with 4 screws (max. 8 mm diameter)
Mounting
Mast mounting
Mast diameter (mm) Default: 30 - 125 // Optional: 40 - 140
Connector 6 x 7/16 DIN Female ( Two ports are eNodeB and four ports are ANT)
312
MTMA-800/E900-12dB-2eNodeBport4ANTport-AISG
Model: ATADU2005
Unit : mm
TMA
313
D - 2. Combiner
Unit:
DC-STOP Band: 698 - 2700 500 DC-Stop < -117
32 x 70.3 x 37
ADCSTOP00 356
** Preliminary Issue
Model: ACOMD2L08
Product Description
Block Diagram
Combiner
ACOMD2L08
317
DC-690-803/824-960-10-11
Model: ACOMD2L08
Electrical Properties
Model ACOMD2L08
Band 1 690 - 803
Pass band (MHz)
Band 2 824 - 960
Port 1 ←→ Port 2 < 0.45 (690 MHz - 803 MHz)
Insertion loss *(dB)
Port 1 ←→ Port 3 < 0.45 (824 MHz - 960 MHz)
Port 1 ←→ Port 2 By-pass (max. 2500 mA)
DC/AISG transparency
Port 1 ←→ Port 3 Stop
Isolation (dB) > 47.0
VSWR < 1.22
Input power (W) Port 1, Port 2, Port3 < 300
Intermodulation products (dBm) < -112 (3rd order; with 2 x 43 dBm)
Environmental Specification
Operating temperature (℃) -40 … +65
Application scene Indoor // Outdoor
IP rating IP67
Lightning protection** (kA) 10 (8/20 us)
Mechanical Specification
Double Unit: 200 x 230 x 107
Combiner dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
Packing dimensions (W x H x D) (mm) 335 x 405 x 265
Combiner weight (kg) Double Unit: ≤ 7.9
Packing weight (kg) ≤ 9.4
Mounting Wall mounting // Mast mounting
Mast diameter (mm) Default: 40 - 135
Connector 7/16 DIN Female (Long neck)
318
DC-690-803/824-960-10-11
Model: ACOMD2L08
Combiner
319
DC-790-862/880-960-01 Model: ACOMD2H09
Product Description
Block Diagram
ACOMD2H09 ACOMD2H18
320
DC-790-862/880-960-01 Model: ACOMD2H09
Electrical Properties
Environmental Specification
IP rating IP67
Mechanical Specification
321
DC-790-862/880-960-01 Model: ACOMD2H09
Unit : mm
322
DC-698-960/1710-2200-01
Model: ACOMD2H11
Product Description
Block Diagram
Combiner
ACOMD2H11
323
DC-698-960/1710-2200-01
Model: ACOMD2H11
Electrical Properties
Model ACOMD2H11
Environmental Specification
IP rating IP67
Mechanical Specification
324
DC-698-960/1710-2200-01
Model: ACOMD2H11
Unit : mm
Combiner
325
DC-698-960/1710-2700-01 Model: ACOMD2H00
Product Description
Block Diagram
ACOMD2H00 ACOMD2H22
326
DC-698-960/1710-2700-01 Model: ACOMD2H00
Electrical Properties
Environmental Specification
IP rating IP67
Mechanical Specification
327
DC-698-960/1710-2700-01 Model: ACOMD2H00
Unit : mm
328
DC-1710-1880/1920-2200-01 Model: ACOMD2H06
Product Description
Block Diagram
Combiner
ACOMD2H06 ACOMD2H08
329
DC-1710-1880/1920-2200-01 Model: ACOMD2H06
Electrical Properties
Environmental Specification
IP rating IP67
Mechanical Specification
330
DC-1710-1880/1920-2200-01 Model: ACOMD2H06
Unit : mm
Combiner
331
DC-1710-2200/2490-2700-10 Model: ACOMD2L04
Product Description
Block Diagram
ACOMD2L04 ACOMD2H16
332
DC-1710-2200/2490-2700-10 Model: ACOMD2L04
Electrical Properties
Port 1 ←→ Port 3 By-pass (max. 2500 mA) By-pass (max. 2500 mA)
DC/AISG transparency
Port 2 ←→ Port 3 Stop By-pass (max. 2500 mA)
Environmental Specification
IP rating IP67
Mechanical Specification
333
DC-1710-2200/2490-2700-10 Model: ACOMD2L04
Unit : mm
334
TC-790-862/880-960/1710-2200-111
Model: ACOMT2H04
Product Description
Block Diagram
Combiner
ACOMD2H04
335
TC-790-862/880-960/1710-2200-111
Model: ACOMT2H04
Electrical Properties
Model ACOMT2H04
Insertion loss* (dB) Port 2 ←→ Port 4 < 0.3 (880 MHz - 960 MHz)
Environmental Specification
IP rating IP67
Mechanical Specification
Double Unit: 220 x 210 x 115
Dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
336
TC-790-862/880-960/1710-2200-111
Model: ACOMT2H04
Unit : mm
Combiner
337
TC-790-862/880-960/1710-2700-111
Model: ACOMT2A02
Preliminary Issue
Product Description
Block Diagram
Port4
DC/AISG By-pass
DC/AISG By-pass
DC/AISG By-pass
ACOMT2A02
338
TC-790-862/880-960/1710-2700-111
Model: ACOMT2A02
Preliminary Issue
Electrical Properties
Model ACOMT2A02
Band 1 790 - 862
Pass band (MHz) Band 2 880 - 960
Band 3 1710 - 2700
Port 1 ←→ Port 4 < 0.3 (790 MHz - 862 MHz)
Insertion loss* (dB) Port 2 ←→ Port 4 < 0.3 (880 MHz - 960 MHz)
Port 3 ←→ Port 4 < 0.15 (1710 MHz - 2200 MHz)
Port 1 ←→ Port 4 By-pass (max. 2500 mA)
DC/AISG transparency Port 2 ←→ Port 4 By-pass (max. 2500 mA)
Port 3 ←→ Port 4 By-pass (max. 2500 mA)
Port 1 ←→ Port 2 > 50
Isolation (dB) Port 2 ←→ Port 3 > 50
Port 1 ←→ Port 3 > 50
VSWR < 1.24
Input power (W) Port 1, Port 2, Port3 < 300
Intermodulation products (dBm) < -110 (3rd order; with 2 x 43 dBm)
Environmental Specification
Operating temperature (℃) -40 … +65
Application scene Indoor // outdoor
IP rating IP67
Lightning protection (kA) 10 (8/20 us)
Mechanical Specification
Double Unit: 220 x 210 x 115
Dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
Packing dimensions (W x H x D) (mm) 335 x 405 x 265
Combiner weight (kg) Double Unit: ≤ 7.5
Packing weight (kg) ≤8.4
Mounting Wall mounting // Mast mounting
Mast diameter (mm) Default: 40 - 135
Connector 7/16 DIN Female (Long neck)
339
TC-790-862/880-960/1710-2700-111
Model: ACOMT2A02
Unit : mm
340
TC-790-960/1710-1880/1920-2200-001 Model: ACOMT2H01
TC-790-960/1710-1880/1920-2200-011 Model: ACOMT2H03
TC-790-960/1710-1880/1920-2200-111 Model: ACOMT2H08
Product Description
Block Diagram
341
TC-790-960/1710-1880/1920-2200-001 Model: ACOMT2H01
TC-790-960/1710-1880/1920-2200-011 Model: ACOMT2H03
TC-790-960/1710-1880/1920-2200-111 Model: ACOMT2H08
Electrical Properties
Insertion loss* (dB) Port 2 ←→ Port 4 < 0.25 (1710 MHz - 1880 MHz)
DC/AISG transparency Port 2 ←→ Port 4 Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA)
Port 3 ←→ Port 4 By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA)
Environmental Specification
IP rating IP67
Mechanical Specification
Double Unit: 190 x 154 x 105
Combiner dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
342
TC-790-960/1710-1880/1920-2200-001 Model: ACOMT2H01
TC-790-960/1710-1880/1920-2200-011 Model: ACOMT2H03
TC-790-960/1710-1880/1920-2200-111 Model: ACOMT2H08
Unit : mm
Combiner
343
TC-690-960/1710-1880/1920-2200-111
Model: ACOMT2A03
Preliminary Issue
Product Description
Block Diagram
Port4
DC/AISG By-pass
DC/AISG By-pass
DC/AISG By-pass
ACOMT2A03
344
TC-690-960/1710-1880/1920-2200-111
Model: ACOMT2A03
Preliminary Issue
Electrical Properties
Model ACOMT2A03
Insertion loss* (dB) Port 2 ←→ Port 4 < 0.25 (1710 MHz - 1880 MHz)
Environmental Specification
IP rating IP67
Mechanical Specification
Double Unit: 196 x 190 x 112
Combiner dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
345
TC-690-960/1710-1880/1920-2200-111
Model: ACOMT2A03
Unit : mm
346
TC-690-960/1710-2200/2300-2690-111
Model: ACOMT2A04
Preliminary Issue
Product Description
Block Diagram
Port4
DC/AISG By-pass
DC/AISG By-pass
DC/AISG By-pass
ACOMT2A04
347
TC-690-960/1710-2200/2300-2690-111
Model: ACOMT2A04
Preliminary Issue
Electrical Properties
Model ACOMT2A04
Insertion loss* (dB) Port 2 ←→ Port 4 < 0.25 (1710 MHz - 2200 MHz)
Environmental Specification
IP rating IP67
Mechanical Specification
Double Unit: 196 x 190 x 112
Combiner dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
348
TC-690-960/1710-2200/2300-2690-111
Model: ACOMT2A04
Unit : mm
Combiner
349
QC-790-960/1710-1880/1920-2200/2490-2700-0010
Model: ACOMQ2M00
QC-790-960/1710-1880/1920-2200/2490-2700-1111
Model: ACOMQ2H00
Product Description
Block Diagram
ACOMQ2M00 ACOMQ2H00
350
QC-790-960/1710-1880/1920-2200/2490-2700-0010
Model: ACOMQ2M00
QC-790-960/1710-1880/1920-2200/2490-2700-1111
Model: ACOMQ2H00
Electrical Properties
Model ACOMQ2M00 ACOMQ2H00
Port 1, Port 2
Input power (W) < 300
Port 3, Port 4
Environmental Specification
Operating temperature (℃) -40 … +65
IP rating IP67
Mechanical Specification
Double Unit: 215 x 200 x 105
Combiner dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
351
QC-790-960/1710-1880/1920-2200/2490-2700-0010
Model: ACOMQ2M00
QC-790-960/1710-1880/1920-2200/2490-2700-1111
Model: ACOMQ2H00
Unit : mm
352
QC-690-960/1710-1880/1920-2200/2300-2690-1111
Model: ACOMQ2A01
Preliminary Issue
Product Description
Block Diagram
Port5
DC/AISG By-pass
DC/AISG By-pass
DC/AISG By-pass
DC/AISG By-pass
ACOMQ2A01
353
QC-690-960/1710-1880/1920-2200/2300-2690-1111
Model: ACOMQ2A01
Preliminary Issue
Electrical Properties
Model ACOMQ2A01
Port 1, Port 2
Input power (W) < 300
Port 3, Port 4
Environmental Specification
Operating temperature (℃) -40 … +65
IP rating IP67
Mechanical Specification
Double Unit: 230 x 220 x 112
Combiner dimensions (W x H x D) (mm)
(without connectors, without mounting brackets)
Packing dimensions (W x H x D) (mm) 335 x 405 x 265
354
QC-690-960/1710-1880/1920-2200/2300-2690-1111
Model: ACOMQ2A01
Unit : mm
Combiner
355
DC-STOP 690-2700
Model: ADCSTOP00
Features
Dimension figure
356
DC-STOP 690-2700
Model: ADCSTOP00
Electrical Properties
Model ADCSTOP00
Port 1 ←→ Port
Isolation for DC signal (dB) ≥ 70
2
Input power (W) Port 1, Port 2 Avg. ≥ 500 (690 - 2700 MHz)
RF Impedance (Ω) 50
Environmental Specification
IP rating IP66
Mechanical Specification
32 x 70.3 x 37
BT dimensions (W x H x D) (mm)
(with connectors and ground screw)
357
E. Bracket&Installation Guide
E - 1. Bracket
E - 1 - 1. Tri-sector Bracket
Antenna Width
Bracket Type Weight (Kg) Dimension (mm) Model Page
Required
TSC-S (3 Sector Clamp-Small) <280mm 5.8 88.9mm (3.5inch) ASMC00001 360
TSC-M (3 Sector Clamp-Medium) <380mm 6.3 114.3mm (4.5inch) ASMC00002 360
TSC-L (3 Sector Clamp-Large) <400mm 6.6 139.7mm (5.5inch) ASMC00003 360
E - 1 - 2. Downtilt Kit
E - 2. Installation Guide
Suitable for antennas whose widths are less than 400 mm and bases are installed
at both ends of the antennas.
Adjustment is available together with standard bracket within antenna package.
Support the third party customized camouflage cover.
Not support antennas with brackets of model F or above.
Wmax
Base
Tri-sector clamp
360
Tri-sector Clamps
Specifications
3 sector clamp
Mounting support clamp Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel
Screws
Stainless steel Stainless steel Stainless steel
Nuts
Installation Guide
Bracket
361
Standard Downtilt kit-A for Panel Antennas
(Wind load Category “Light”)
Model: ASMDT0A01
0.7 0 - 20
Sheet Metal: Hot-dip galvanized steel
1.4 0 - 12 0.6 0.7 260 x 98 x 50
Screws / nuts / washers: Stainless steel
2.0 0- 8
221
190
140
57
76
Unit: mm
NOTE
Downtilt kit must be combined with corresponding models of clam for antenna installation.
Installation must follow the antenna installation guide within antenna package.
362
Standard Downtilt kit-B for Panel Antennas
(Wind load Category “Medium”)
Model: ASMDT0B01
0.8 0 - 20
Sheet Metal: Hot-dip galvanized steel
1.4 0 - 16 1.3 1.8 315 x 160 x 105
Screws / nuts / washers: Stainless steel
2.0 0 - 12
222
278
178
93
139
Unit: mm
NOTE
Downtilt kit must be combined with corresponding models of clam for antenna installation.
Installation must follow the antenna installation guide within antenna package.
Installation Guide
Bracket
363
Standard Downtilt kit-C for Panel Antennas
(Wind load Category “Medium”)
Model: ASMDT0C01
1.4 0 - 16
Sheet Metal: Hot-dip galvanized steel
2.0 0 - 12 2.1 2.7 330 x 160 x 135
Screws / nuts / washers: Stainless steel
2.6 0- 8
223
179
294
100
142
Unit: mm
NOTE
Downtilt kit must be combined with corresponding models of clam for antenna installation.
Installation must follow the antenna installation guide within antenna package.
364
Standard Downtilt kit-D for Panel Antennas
(Wind load Category “Heavy”)
Model: ASMDT0D01
1.4 0 - 16
Sheet Metal: Hot-dip galvanized steel
2.0 0 - 12 2.1 2.7 330 x 170 x 135
Screws / nuts / washers: Stainless steel
2.6 0- 8
224
297
162
94
136
Unit: mm
NOTE
Downtilt kit must be combined with corresponding models of clam for antenna installation.
Installation must follow the antenna installation guide within antenna package.
Installation Guide
Bracket
365
Standard Downtilt kit-G for Panel Antennas
(Wind load Category “Heavy”)
Model: ASMDT0G01
1.4 0 - 16
Sheet Metal: Hot-dip galvanized steel
2.0 0 - 12 4.3 4.8 385 x 240 x 135
Screws / nuts / washers: Stainless steel
2.6 0-8
176
250
319
180
218
Unit: mm
NOTE
Downtilt kit must be combined with corresponding models of clam for antenna installation.
Installation must follow the antenna installation guide within antenna package.
366
Standard Downtilt kit-F for Panel Antennas
(Wind load Category “Heavy”)
Model: ASMDT0F01
1.4 0 - 16
Sheet Metal: Hot-dip galvanized steel
2.0 0 - 12 3.1 3.7 360 x 170 x 120
Screws / nuts / washers: Stainless steel
2.6 0-8
249
327
180
106
150
Unit: mm
NOTE
Downtilt kit must be combined with corresponding models of clam for antenna installation.
Installation must follow the antenna installation guide within antenna package.
Installation Guide
Bracket
367
Extension Clamps Kit-B for Panel Antennas
Model: ASMC00006
68
20
for Clamps Kit-F
110.5
50
70
160
194
The expand interface
2-Φ6.5 2-Φ9 The expand interface for
for Clamps Kit-A
Clamps Kit-B , Clamps Kit-
C and Clamps Kit-D
35
68
228 Unit: mm
NOTE
Clamps kit must be combined with corresponding models of clam for antenna installation.
Installation must follow the antenna installation guide within antenna package.
368
Wall-mounting Kit-A Hardware
Model: ASMWM0001
Suitable for all panels with an antenna housing width (Wmax) less than 400 mm.
Number of pieces 2
Material Screws
Stainless steel
Nuts
Ø 12
NOTE
The expansion bolts for concrete wall mounting are provided, other wall mounting screws are not supplied, they must be
chosen by installer according to the mounting condition.
Installation Guide
Bracket
369
Antenna with Type A Brackets Installation Guide
Torque wrench
ASMDT0A01
13 mm combination
M8 (1 PCS)
Inclinometer wrench (2 PCS) (2 PCS) (2 PCS)
(4 PCS)
2 PCS
370
Installation with Downtilt Kit
Protrusion
Protrusion
The side of the downtilt kit with a protrusion is Insert the bolt from the side with the
outside. Protrusion.
Protrusion
371
2 Install the bracket
Tighten the
upper bracket.
Method 2: Using an inclinometer
Tighten the
lower bracket.
Finally, tighten all the nuts. The recommended torque M8 is 18 N·m
372
Antenna with Type B and Type C Brackets Installation Guide
(1 PCS)
13 mm combination
wrench (2 PCS)
(2 PCS)
(1 PCS)
Inclinomet
16 mm combination er
wrench (2 PCS) ASMDT0B01
or
ASMDT0C01
M10 M10 M8
(4 PCS) (2 PCS) (4 PCS) (1 PCS)
Torque wrench (1 PCS)
M8
373
3 Install the antenna
The mechanical
downtilt of the Install and tighten the nuts. The
antenna is fixed to The same installation method applies to recommended torque M10 is 40 N·m.
0° and cannot be both upper and lower brackets.
adjusted.
M10 =
40 N·m
Check and tighten all the nuts when the
installation is complete. The operating
torques are given in the following
figures.
Protrusion
Label
Protrusion
Label
374
2 Install the bracket
The same installation method applies to Install and tighten the nuts. The recommended
both upper and lower brackets. torque M10 is 40 N·m.
Tighten the
lower bracket.
used.
375
Antenna with Type D Brackets Installation Guide
(1 PCS)
(1 PCS)
13 mm combination
wrench (2 PCS) (2 PCS)
16 mm combination
wrench (2 PCS) Inclinometer
ASMDT0D01
M10 x 150 M10 x 110 (1 PCS)
Torque wrench (4 PCS) (1 PCS) (1 PCS)
376
3 Install the antenna
The mechanical
downtilt of the
antenna is fixed
The same installation method applies to Install and tighten the nuts. The recommended torque
to 0° and
both upper and lower brackets. M10 is 40 N·m.
cannot be
adjusted.
M10 = 40
N·m
Label
Label
377
2 Install the bracket
The same installation method applies to Install and tighten the nuts. The recommended
both upper and lower brackets. torque M10 is 40 N·m.
Tighten the
lower bracket.
Loosen all the nuts as shown Recommended torque M10 = 40N·m
in the figure to adjust the
downtilt. After the
adjustment is complete,
tighten all the nuts.
Check the component shape
and the position of screws
before the adjustment.
Strictly the operating torques
given in the following figures
must be used.
378
Antenna with Type F Brackets Installation Guide
(1 PCS)
13 mm combination
wrench (2 PCS)
(2 PCS)
(1 PCS)
16 mm combination
wrench (2 PCS) Inclinometer
M8
(4 PCS)
ASMDT0D01
M10 M12 M10 x 110 (1 PCS)
(4 PCS) (4 PCS) (1 PCS)
Torque wrench (1 PCS)
Install bolts on the antenna base. The Align the bolt with the mounting hole on the clamp and
same installation method applies to determine the bolt model according to the position of the
both upper and lower bases. mounting hole. Replace the bolt if the bolt model is incorrect.
Then, install and tighten the flat washer, spring washer and nut.
379
3 Install the antenna
M12 =
50 N·m
The mechanical
downtilt of the
antenna is fixed
to 0° and
cannot be
adjusted.
380
2 Install the bracket
For details about how to select bolts for fixing the bracket, see
"Install the clamps" .
The same installation method applies to both upper and lower
brackets.
The same installation method applies to both upper and lower brackets. Install and
tighten the nuts. The recommended torque M12 is 50 N·m.
Tighten the
lower bracket.
381
Huawei Antenna Test Standard
MIL - STD - 810 150mm/h, 31m/s, 4surfaces, more Visual/physical exam VSWR ISO
Wind Driven Rain GR - 487 - CORE
Method 506.3 0.5mm-4.5mm, 45° than 120min and PIM (pre and post)
Huawei antenna supports NGMN recommendations on Base Station Antenna Standards (BASTA).
General Disclaimer
The information in this document may contain
predictive statements including, without limitation,
statements regarding the future financial and
operating results, future product portfolio, new
technology, etc. There are a number of factors that
could cause actual results and developments to
differ materially from those expressed or implied
in the predictive statements. Therefore, such
information is provided for reference purpose only
and constitutes neither an offer nor an acceptance.
Huawei may change the information at any time
without notice.
www.huawei.com/antenna