Anda di halaman 1dari 2

ES-LFUSG-B

For Residential and Commercial Applications


Job Name_______________________________________ Contractor_______________________________________ Job Location_____________________________________ Approval_________________________________________ Engineer_ ________________________________________ Contractors P.O. No._ ____________________________ Approval_ ________________________________________ Representative_ __________________________________

LEAD FREE* Series LFUSG-B


Under Sink Guardian
Series LFUSG-B Under Sink Guardian 38" (10mm) compression fitting ther mo stat ic mix ing valves maintain and limit hot water to desired se lect able temperature between 80F and 120F (27C and 49C) with flow rates as low as 0.5 gpm (1.9 lpm) and as high as 2.5 gpm (9.5 lpm). The mix ing valve is listed to ASSE Standard 1070 for sin gle fix ture applications. The LFUSG-B se ries uses a dou ble throt tling de sign to control both the hot and cold wa ter sup ply to the mixed outlet.The LFUSG-B features Lead Free* construction to comply with Lead Free* installation requirements. The su pe ri or flow char ac ter is tics of this valve provide ac cu rate tem per at ure con trol (3F) with low pres sure drop. As an add ed fea ture, the LFUSG-B -M1 in cor po rates dual check valves to pro tect against cross-flow and integral screens to filter out debris.
LFUSG-B-M1

ASSE 1070 Listed U.S. Pat. 6,315,209 Application Note Delivery of water to fixtures intended for use in bath ing or wash ing should always be controlled by valves listed to ASSE Stan dard 1016 or ASSE Standard 1070 such as Watts Series LFUSG or LFMMV mixing valves. These valves provide the user with both scald pro tec tion and pro tec tion from thermal shock. The installer should always test to verify temperature setting after installation.

Features

 Lead Free* Brass body construction.  Maintains mixed water temperature to 3F up to 120F (49C). Installs easily between the stop valves and faucet  Includes tamper resistant locking cap to prevent accidental mis-adjustment.  Built-in check valves prevent migration of hot water to cold and cold water to hot water piping. Provided with cap for three port application.  Integral strainer with 40 mesh stainless steel screens to filter out debris. The unit is intended for under sink installation to con trol the hot water temperature and prevent ac ci den tal scald ing. The water temperature must be adjusted by the in stall er using a thermometer to measure the hot water tem per at ure at the faucet outlet. Maximum tem per a ture of 110F (43C) is recommended.

Materials
Body: Lead Free*Brass Spring: Stainless steel Ball: Stainless steel Rubber Disc: Buna-N O-rings: Buna-N Piston: UDEL-P1700 Metal Disc: Stainless steel

Thermostat: Copper

Applications

Approval
ASSE 1070 CSA B-125

Specifications

A Thermostatic Mixing Valve shall be installed on the hot water supply to the fix ture. The valve shall be ASSE Standards 1070 listed and control the temperature of the hot water. It shall have a Lead Free* brass body. Body shall be constructed using Lead Free* Brass. Lead Free* under counter thermostatic valves shall comply with state codes and standards, where applicable, requiring reduced lead content. The valve shall include integral check valves, integral screens and an ad just ment cap with lockin fea ture. The valve shall be pro vid ed with 38" (10mm) male com pres sion fittings. The valve shall be Watts Series LFUSG-B. For satin chrome finish specify SC.

*The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight.

Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.

Basic Construction
Button Head Screw Locking Adjusting Cap Ball O-ring Stem Thermostat Metal Disc Piston O-ring Spring Body Check Module

Pressure Temperature
Minimum supply pressure: 30psi (207 kPa) Hot inlet temperature: 120F-180F (49C-82C) Cold inlet temperature: 39F-80F (3.8C-27C) Minimum inlet temperature differential: 15F (9C) Temperature out: 80F-120F (27C-49C) Maximum pressure: 150psi (10.3 bar) Maximum Pressure differential between hot and cold inlet supplies: 25%.

Check module

Mesh Screen

Flow Capacity 38" LFUSG-B-M1


kPa 620 551 482 413 345 276 207 138 69 0 psi 90 80 70 60 50 40 30 20 10 0

0 0

1.00 3.8

2.00 7.8

3.00 11.4

4.00 gpm 15.2 lpm

Dimensions Weights
Models LFUSG-B-M1 LFUSG-B-SC*-M1
* SC Satin Chrome Finish
38 38

A Size in. mm 78 78 in. 5316 5316 " Comp. 3564 " Comp. 3564

B mm 132 132

Weight lbs. kgs. 1.0 1.0 .45 .45

Typical Installations
Two Handle Faucet Sensor Faucet

LFUSG-B-M1

A Watts Water Technologies Company

USA: No. Andover, MA Tel. (978) 688-1811 Fax: (978) 794-1848 www.watts.com Canada: Burlington, ONT. Tel. (905) 332-4090 Fax: (905) 332-7068 www.wattscanada.ca

ES-LFUSG-B 1101

2011 Watts

Anda mungkin juga menyukai