Anda di halaman 1dari 9

Mounting Bracket Linear Structural Simulation

Analyzed File: Week 9 - Problem Set.iam


Autodesk Inventor Version: 2017 (Build 210142000, 142)
Creation Date: 04/07/2019, 19:54
Study Author: NND (Franando)
Summary:

Project Info (iProperties)

Summary
Title
Author dmm70056

Project
Part Number Problem Set
Designer dmm70056
Cost Rp0

Status
Design Status WorkInProgress

Physical
Mass 45,1174 lbmass
Area 572,116 in^2
Volume 157,467 in^3
x=-3,54289 in
Center of Gravity y=-3,59619 in
z=1,39975 in

Note: Physical values could be different from Physical values used by FEA reported below.

Simulation:1
General objective and settings:
Design Objective Single Point
Study Type Static Analysis
Last Modification Date 04/07/2019, 19:45
Detect and Eliminate Rigid Body Modes No
Separate Stresses Across Contact
No
Surfaces
Motion Loads Analysis No

Mesh settings:
Avg. Element Size (fraction of model
0,05
diameter)
Min. Element Size (fraction of avg. size) 0,2
Grading Factor 1,5
Max. Turn Angle 60 deg
Create Curved Mesh Elements No
Use part based measure for Assembly mesh Yes

Design Constraint definition:


Constraint Name Constraint Type Limit Safety Factor
Min Safety Factor View the value 1
Max Von Mises
View the value 1
Stress
Mass View the value 1
Max Displacement View the value 1

Material(s)
Name Steel, Mild
Mass Density 0,283599 lbmass/in^3
General Yield Strength 30022,8 psi
Ultimate Tensile Strength 50038 psi
Young's Modulus 31908,3 ksi
Stress Poisson's Ratio 0,275 ul
Shear Modulus 12513,1 ksi
Bracket
Mounting Plate
Part Name(s)
dowel
dowel
Name Cast Bronze
Mass Density 0,320449 lbmass/in^3
General Yield Strength 18564,8 psi
Ultimate Tensile Strength 39885,4 psi
Young's Modulus 15896,1 ksi
Stress Poisson's Ratio 0,335 ul
Shear Modulus 5953,61 ksi
Bushing 1
Part Name(s)
Bushing 2
Name Stainless Steel
Mass Density 0,289018 lbmass/in^3
General Yield Strength 36259,4 psi
Ultimate Tensile Strength 78320,4 psi
Young's Modulus 27992,3 ksi
Stress Poisson's Ratio 0,3 ul
Shear Modulus 10766,3 ksi
Pin
Shaft
ISO 4162 M12 x 45
Part Name(s)
ISO 4162 M12 x 45
ISO 4162 M12 x 45
ISO 4162 M12 x 45

Operating conditions

Remote Force:1
Load Type Remote Force
Magnitude 800,000 lbforce
Vector X 0,000 lbforce
Vector Y 800,000 lbforce
Vector Z 0,000 lbforce
Remote Point X 0,000 in
Remote Point Y 0,875 in
Remote Point Z 3,000 in

Selected Face(s)
Remote Force:2
Load Type Remote Force
Magnitude 500,000 lbforce
Vector X 0,000 lbforce
Vector Y -500,000 lbforce
Vector Z 0,000 lbforce
Remote Point
-6,000 in
X
Remote Point Y -1,500 in
Remote Point Z 5,063 in

Selected Face(s)
Fixed Constraint:1
Constraint
Fixed Constraint
Type

Selected Face(s)

Contacts (Bonded)
Name Part Name(s)
Bonded:1 Bracket:1
Bushing 1:1
Bracket:1
Bonded:2
Bushing 2:1
Bracket:1
Bonded:3
Shaft:1
Bracket:1
Bonded:4
Mounting Plate:1
Bushing 1:1
Bonded:5
Shaft:1
Bushing 1:1
Bonded:6
Shaft:1
Bushing 2:1
Bonded:7
Pin:1
Bracket:1
Bonded:8
dowel:2
Bracket:1
Bonded:9
dowel:1
Bracket:1
Bonded:10
ISO 4162 M12 x 45:1
Bracket:1
Bonded:11
ISO 4162 M12 x 45:1
Bracket:1
Bonded:12
ISO 4162 M12 x 45:4
Bracket:1
Bonded:13
ISO 4162 M12 x 45:4
Bracket:1
Bonded:14
ISO 4162 M12 x 45:2
Bracket:1
Bonded:15
ISO 4162 M12 x 45:2
Bracket:1
Bonded:16
ISO 4162 M12 x 45:3
Bracket:1
Bonded:17
ISO 4162 M12 x 45:3
Mounting Plate:1
Bonded:18
dowel:1
Mounting Plate:1
Bonded:19
dowel:2
Mounting Plate:1
Bonded:20
ISO 4162 M12 x 45:4
Mounting Plate:1
Bonded:21
ISO 4162 M12 x 45:1
Mounting Plate:1
Bonded:22
ISO 4162 M12 x 45:2
Mounting Plate:1
Bonded:23
ISO 4162 M12 x 45:3

Results
Reaction Force and Moment on Constraints

Constraint Reaction Force Reaction Moment


Name Magnitude Component (X,Y,Z) Magnitude Component (X,Y,Z)
0 lbforce 5,24349 lbforce ft
Fixed Constraint:1 290,341 lbforce -290,341 lbforce 331,68 lbforce ft 1,1377 lbforce ft
-0,158719 lbforce -331,637 lbforce ft

Result Summary
Name Minimum Maximum
Volume 157,467 in^3
Mass 44,9911 lbmass
Von Mises Stress 0,0000121766 ksi 22,914 ksi
1st Principal Stress -4,42273 ksi 28,2296 ksi
3rd Principal Stress -20,2333 ksi 4,10909 ksi
Displacement 0 in 0,00768452 in
Safety Factor 1,31024 ul 15 ul

Figures

Von Mises Stress


Displacement

Safety Factor
D:\franando\TUGAS KULIAH\semester6\dq\bab 7\PSA 6_FILES\Week 9 - Problem Set.iam

Anda mungkin juga menyukai