Untuk Mengecek Alarm
Untuk Mengecek Alarm
Untuk Mengecek Alarm
…………………………………………………………………………………………………………………………………………
Melihat VSWR alarm Node B
Lihat cabx
loadHs false if txHs loadHs = true
set proxyxxx loadHs false/True
2.
Change CV
Cvls.
Cvms <cvname> [<operator>] [<comment>]
Cvcu melihat cv yg active
………………………………………………………………………………………………………………………………………...
Baca log file
lhsh 001200/port_8_dev_6 te log read baca log file
………………………………………………………………………………………………………………………………………...
Carrier Average Rssi and Transmitted Power
$pmr
<= AvgRssi -80.00 Good
………………………………………………………………………………………………………………………………………...
Check TMA
PADEMANGAN TIMUR> lt tma
PADEMANGAN TIMUR>get TMA
………………………………………………………………………………………………………………………………………...
Non Aktif LNA di ASC
10.149.14.105> lhsh 001200/port_9_dev_19 asc lnaerr
$ lhsh 001200/port_9_dev_19 asc lnaerr
ERROR: LNA branch A, one transistor faulty
LNA transistors branch B OK
10.149.14.105> lhsh 001200/port_9_dev_19 asc lnaerrset n a
lhsh 001200/port_9_dev_19 asc lnaerrset n a
No LNA transistor faults set for branch a
10.149.14.105> lhsh 001200/port_5_dev_17 asc lnaerr
lhsh 001200/port_5_dev_17 asc lnaerr
LNA transistors branch A OK
LNA transistors branch B OK
………………………………………………………………………………………………………………………………………
Check OBIF
Bekasi_Bintara> lt all
Bekasi_Bintara> cabx
Bekasi_Bintara> get OBIF
Bekasi_Bintara> get optical
………………………………………………………………………………………………………………………………………...
Check sektor status
lt utrancell
182_Jamrut> lt all
182_Jamrut> pr fach
SET Clock NODE B
$ setclock yyyy-mm-dd hh:mm:ss
eg:
$ setclock 2006-10-26 18:39:00
Print Out Clock
$Readclock
………………………………………………………………………………………………………………………………………...
Ubah antennaSupervisionThreshold
$ lt antenna
$ get Antenna
$ set antennaSupervisionThreshold 20 (jika 0 maka VSWR tidak tersupervisi)
………………………………………………………………………………………………………………………………………...
Melihat status transmisi
Pada EMAS RNC, jika site A down E1 harus merah. Akan tetapi jika site A down dan LED E1 hijau, hal ini
pasti karena di loop ke RNC.
Pada Moshell RNC, lt E1 dan lst, jika site down dan Op state disable, maka TRS problem (open), tapi jika
Op state enable, maka TRS loop ke RNC.
Check E1.
MoShell> lst ImaGroup=ES-2-2-1 dis
MoShell> lk <ImaLink proxy #> phy
MoShell> lpr Subrack=...,Slot=..,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4.....
MoShell> lpget <PhyPath MO proxy #>
RNC>lt all
RXJKT02> for ever
Enter commands (one per line), then type "done"
> pget 685 687 689 691 es
> pget 685 687 689 691 uas
> wait 1800
> done ((to check performance site in E1,see the value,is there any counter in every time ? if yes,the
performance is going to worse,if the value is stabil,the performance is OK )
RNC> pget es1-2-1 (lihat Value pmReceivedAtmCells, pmSecondsWithUnexp, pmTransmittedAtmCells)
Check Kelerusan E1
RNSBY01> strt check VC pertama dan ke dua (bila ada)
RNSBY01> lt vc
RNSBY01> lacc atmport=es1-24-17 eteloopback
2193 AtmPort=ES1-24-17,VplTp=vp1,VpcTp=1,VclTp=vc32 eteLoopBack 0
>>> Return value = false
Atau lewat EM RNC equipment pilih MS atau ES terus pilih VC ke XX… cari E1 keXX
………………………………………………………………………………………………………………………………………...
Check E1 from RXI
RXI> lt aal2
RXI>lst iublink
RXI>lt all
RXI>lst imagroup=xxxx (form vclTpId copy MS-16-1-IMA3)
RXI>get porxy
RXI> stcp .0 lht crossconnect yg disable
………………………………………………………………………………………………………………………………………...
Melihat status RBS yang available
RNC> str
RNC> str –I 1003 melihat RBS 1003
RNC> lt utrancell
RNC> get utrancell
RNC> lst utrancell
RNC> set (no proxy) primaryCpichpower (value) per 3 dB max.
………………………………………………………………………………………………………………………………………...
Melihat RNC ok atau gak
RNC> std
………………………………………………………………………………………………………………………………………...
Melihat cell error code
RNC> tg
………………………………………………………………………………………………………………………………………...
Troubleshooting Melihat status E1
site> lt E1
site>pget e1 es
RNC> lst
………………………………………………………………………………………………………………………………………...
Ubah Cell ID
RJK01> lt cell
RJK01> lt cell=0920
RJK01> get cell=0920 local
RJK01> get cell=0920
RJK01> set 1489 localCellId=9201
………………………………………………………………………………………………………………………………………...
Block/DeBlock Cell CD12 IUBLINK
RNSBY01> lt cell
RNSBY01>get {IUBLINK} /Cell ID
RNSBY01>lst {IUBLINK} /Cell ID
RNSBY01>bl {proxy} untuk block
RNSBY01>deb {proxy} untuk deblock
RNSBY01>lbl {IUBLINK} CD12 di block sekaligus
RNSBY01>ldeb {IUBLINK} CD12 di deblock sekaligus
………………………………………………………………………………………………………………………………………...
Melihat VSWR alarm Node B
Lihat cabx
loadHs false if txHs loadHs = true
set proxyxxx loadHs false/True
2.
Change CV
Cvls.
Cvms <cvname> [<operator>] [<comment>]
Cvcu melihat cv yg active
………………………………………………………………………………………………………………………………………...
Baca log file
lhsh 001200/port_8_dev_6 te log read baca log file
………………………………………………………………………………………………………………………………………...
Carrier Average Rssi and Transmitted Power
$pmr
<= AvgRssi -80.00 Good
………………………………………………………………………………………………………………………………………...
Check TMA
PADEMANGAN TIMUR> lt tma
PADEMANGAN TIMUR>get TMA
………………………………………………………………………………………………………………………………………...
Non Aktif LNA di ASC
10.149.14.105> lhsh 001200/port_9_dev_19 asc lnaerr
$ lhsh 001200/port_9_dev_19 asc lnaerr
ERROR: LNA branch A, one transistor faulty
LNA transistors branch B OK
10.149.14.105> lhsh 001200/port_9_dev_19 asc lnaerrset n a
lhsh 001200/port_9_dev_19 asc lnaerrset n a
No LNA transistor faults set for branch a
10.149.14.105> lhsh 001200/port_5_dev_17 asc lnaerr
lhsh 001200/port_5_dev_17 asc lnaerr
LNA transistors branch A OK
LNA transistors branch B OK
………………………………………………………………………………………………………………………………………
Check OBIF
Bekasi_Bintara> lt all
Bekasi_Bintara> cabx
Bekasi_Bintara> get OBIF
Bekasi_Bintara> get optical
………………………………………………………………………………………………………………………………………...
Check sektor status
lt utrancell
182_Jamrut> lt all
182_Jamrut> pr fach
SET Clock NODE B
$ setclock yyyy-mm-dd hh:mm:ss
eg:
$ setclock 2006-10-26 18:39:00
Print Out Clock
$Readclock
………………………………………………………………………………………………………………………………………...
Ubah antennaSupervisionThreshold
$ lt antenna
$ get Antenna
$ set antennaSupervisionThreshold 20 (jika 0 maka VSWR tidak tersupervisi)
………………………………………………………………………………………………………………………………………...
Melihat status transmisi
Pada EMAS RNC, jika site A down E1 harus merah. Akan tetapi jika site A down dan LED E1 hijau, hal ini
pasti karena di loop ke RNC.
Pada Moshell RNC, lt E1 dan lst, jika site down dan Op state disable, maka TRS problem (open), tapi jika
Op state enable, maka TRS loop ke RNC.
Check E1.
MoShell> lst ImaGroup=ES-2-2-1 dis
MoShell> lk <ImaLink proxy #> phy
MoShell> lpr Subrack=...,Slot=..,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4.....
MoShell> lpget <PhyPath MO proxy #>
RNC>lt all
RXJKT02> for ever
Enter commands (one per line), then type "done"
> pget 685 687 689 691 es
> pget 685 687 689 691 uas
> wait 1800
> done ((to check performance site in E1,see the value,is there any counter in every time ? if yes,the
performance is going to worse,if the value is stabil,the performance is OK )
RNC> pget es1-2-1 (lihat Value pmReceivedAtmCells, pmSecondsWithUnexp, pmTransmittedAtmCells)
Check Kelerusan E1
RNSBY01> strt check VC pertama dan ke dua (bila ada)
RNSBY01> lt vc
RNSBY01> lacc atmport=es1-24-17 eteloopback
2193 AtmPort=ES1-24-17,VplTp=vp1,VpcTp=1,VclTp=vc32 eteLoopBack 0
>>> Return value = false
Atau lewat EM RNC equipment pilih MS atau ES terus pilih VC ke XX… cari E1 keXX
………………………………………………………………………………………………………………………………………...
Check E1 from RXI
RXI> lt aal2
RXI>lst iublink
RXI>lt all
RXI>lst imagroup=xxxx (form vclTpId copy MS-16-1-IMA3)
RXI>get porxy
RXI> stcp .0 lht crossconnect yg disable
………………………………………………………………………………………………………………………………………...
Melihat status RBS yang available
RNC> str
RNC> str –I 1003 melihat RBS 1003
RNC> lt utrancell
RNC> get utrancell
RNC> lst utrancell
RNC> set (no proxy) primaryCpichpower (value) per 3 dB max.
………………………………………………………………………………………………………………………………………...
Melihat RNC ok atau gak
RNC> std
………………………………………………………………………………………………………………………………………...
Melihat cell error code
RNC> tg
………………………………………………………………………………………………………………………………………...
Troubleshooting Melihat status E1
site> lt E1
site>pget e1 es
RNC> lst
………………………………………………………………………………………………………………………………………...
Ubah Cell ID
RJK01> lt cell
RJK01> lt cell=0920
RJK01> get cell=0920 local
RJK01> get cell=0920
RJK01> set 1489 localCellId=9201
………………………………………………………………………………………………………………………………………...
Block/DeBlock Cell CD12 IUBLINK
RNSBY01> lt cell
RNSBY01>get {IUBLINK} /Cell ID
RNSBY01>lst {IUBLINK} /Cell ID
RNSBY01>bl {proxy} untuk block
RNSBY01>deb {proxy} untuk deblock
RNSBY01>lbl {IUBLINK} CD12 di block sekaligus
RNSBY01>ldeb {IUBLINK} CD12 di deblock sekaligus
………………………………………………………………………………………………………………………………………...
CEK SCRAMBLING CODE/ PNCODE
RJK01>lt all
RJK01> get all primaryScramblingCode
Atau:
RJK01> get utrancell=4184 primaryScramblingCode - utk satu cell
………………………………………………………………………………………………………………………………………...
CEK PARAMETER CELL
RNC1> lt utrancell
RNC1> get 13091 cell 1309 sektor 1
………………………………………………………………………………………………………………………………………...
CEK STATUS CROSSCONNECT
RXI>> stc 2051 --> show all crossconnections where the information matches "2051" (in the case
below, where the atmport is 2051)
RXI >> stc .* 0 --> show all crossconnections that are disabled.
………………………………………………………………………………………………………………………………………...
CEK STATUS IubLink
RNSBY01> lst .1040
………………………………………………………………………………………………………………………………………...
CEK STATUS CELL
RNSBY01> str | grep 1040
………………………………………………………………………………………………………………………………………...
CEK STATUS CELL
RNSBY01> lst .SBY040
……………………………………………………………………………………………………………………………………...
CEK INTERFERENCE
RNJKT01> tgd cell=51361 ulinterference celldata cell 5136 sektor 1
Atau:
RNJKT01> dyncelldata cid 51361
CEK ULINTERFERENCE
IubDataStreamsId 1
maxHsRate 60
noOfCommonStreams 14
noOfDedicatedStreams 17
userLabel
noOfCommonStreams = n*4
maxHsRate 15= 1E1
Lst .iub
Get proxy
Lacc eteloopback
………………………………………………………………………………………………………………………………………...
KILL JVM RNC
TELNET IP RNC
$lhsh 001200 pglist –e
$lhsh 001200 pgkill 8 (List no 8 handle Java)
………………………………………………………………………………………………………………………………………...
Tracert
CEK MGW
1. Check capacity
lhsh xxxx00
capi tot (on all boards)
3. check disks
mirror stat
lhsh 000300 mirror stat
6. Check hardware
run
$cat EXCEP_070505_1600.log | egrep RRCConRel | egrep -i exception | egrep 56028 | sed 's/ = /=/g' |
awk '{ print $4 " " $7 " " $11 }' | sort -n | uniq -c | sort +1n
$cat EXCEP_070505_1600.log
………………………………………………………………………………………………………………………………………...
get utrancell=48231 sf8adm|sf16adm|sf32adm
UtranCell=48231 sf16Adm 16
UtranCell=48231 sf32Adm 32
UtranCell=48231 sf8Adm 8
1. Install the Upgrade Package software to OSS, dont forget to unzip the file in OSS with command :
-->unzip <Name_of_file>
2. Run RANOS (WCDMA RAN OSS Explorer) -->GO to Configuration menu --> chose Hardware and
Software management --> choose SMO
3. Go to software menu in SMO, choose the software-->right click choose Synhcronize CPP SW Package
4. Go to Network menu --> Find RBS or RNC that want to Upgrade --> right click and choose Upgrade
5. Choose software upgrade and click next
6. Dont thick the "Use associated software FTP service for each NE" and choose "UTRAN SOFTWARE"
7. In TAB Jobs Configuration --> Thick the 2 upper point --> Installation (Immediate)
--> Verify Upgrade (Manual)
8. Click NEXT and in Paramaeter choose Software and In Installation load module transfer type choose
FULL
9. Go to JOBS menu and see the progress/log of Install Software (wait until it show the activity install
complete) after activity install complete
10.Go to NE Thread again, right click and select Start NE Threads --> this activity will upgrade the
node go to JOBS menu and see the progress/log of Upgrade (wait until it show the activity upgrade
complete)
11. After the upgrade complete back to NETWROKS menu right click and choose ADJUST
12. In menu adjust thick All Filters and Jobs scheduling Immediate
13. Go to JOBS menu and see the log, wait until Adjust activity complete
14.Go to network menu Choose RBS or RNC want to Upgrade, right click choose Upgrade.
15. In Jobs Configuration Thick Upgrade "Immediate", Confirm Upgrade "Manual" and SWAdjust
"Manual"
16. TAB Upgrade choose Reboot Node upgrade
$ moshell 160.xx.xx.xx
RNC> lt all
RNC> strt
.....................................................................................................................
Following XX sites are up:
------------------------------------------------------------------------------------------------------------
MOD IUBLINK CELLNAMES CFRPHEM1 CFRPHEM2 CFRPHEM3 CFRPHEM4 CFRPHEM5 CFRPHEM6 ICDS TN ATMPORTS
---------------------------------------------------------------------------------------------------------------------
1061 b1157XXX XXX157W-
1/2/3 11111 11111 11111 1 1 I
1081 b1284XXY XXY284W-1/2/3 11111 11111 11111 1111 A MS11-2-
IMA37-44
;;
;;
3241 b1314XYX XYX314W-
1/2/3 11111 11111 11111 11111 11111 11111 1 1 I
---------------------------------------------------------------------------------------------------------------------
ket:
MOD: Module RNC yang menghandle Node-B
IUBLINK : Label IuB interface Node-B
CELL (CFRPHEMX): 1st digit (C) = status cell
3 digit berikutnya (FRP)= status common channels (fach/rach/pch).
5th digit (H) = status HSDPA channel (hsdsch).
6th digit (E) = status Enhanced uplink channel (eul)
ICDS: 1st digit = status Iublink
2nd digit = status nbapCommon
3rd digit = status nbapDedicated
4th digit = status Synchronisasi Node-B
TN: jenis transmisi IuB
I = berbasis IP address
A = ATM
ATMPORTS: hanya untuk yang menggunakan ATM
cth: MS11-2-IMA37-44 : MS11=MainSubrack slot 11, port 2
: IMA37-44=sys 37 s/d 44 (8 E1)
Status: L=Locked, 0=Disabled, and 1=Enabled
Offline moshell
Ada 2 cara
Cara 1 : command "dcgk"
contoh :
~$ dcgk
Checking ip contact...OK
RXI> lt all
Checking MOM version...CPP_MOM_MOM-CPP_4.3.3.8-3_0
Last MO: 5530. Loaded 5530 MOs. Total: 5531 MOs.
==================================================================================
===============================
3627 TransportNetwork=1,Aal2PathVccTp=b072a2
==================================================================================
===============================
Aal2PathVccTpId b072a2
aal2PathId 722
aal2PathOwner true
aal2QoSAvailableProfiles 3 (CLASS_A_B)
aal2QoSProfileId Aal2QosProfile=ad10bd20
administrativeState 1 (UNLOCKED)
alarmReport 2 (ALARM_LOC)
availabilityStatus 0 (NO_STATUS)
continuityCheck false
counterMode 0 (PM_MODE_OFF)
nomPmBlocksize 1024 (NOM_PM_BLKSIZE_2_10)
operationalState 1 (ENABLED)
remoteBlockingState 1 (REMOTELY_UNBLOCKED)
reservedBy Aal2Sp=1,Aal2Ap=b072,Aal2PathDistributionUnit=b072
timerCu 10
userLabel Aal2PathVccTp b072a2
vclTpId AtmPort=MS-18-1-12,VplTp=vp1,VpcTp=1,VclTp=vc40
==================================================================================
===============================
3628 TransportNetwork=1,Aal2PathVccTp=b072a1
==================================================================================
===============================
Aal2PathVccTpId b072a1
aal2PathId 721
aal2PathOwner true
aal2QoSAvailableProfiles 3 (CLASS_A_B)
aal2QoSProfileId Aal2QosProfile=ad10bd20
administrativeState 1 (UNLOCKED)
alarmReport 2 (ALARM_LOC)
availabilityStatus 0 (NO_STATUS)
continuityCheck false
counterMode 0 (PM_MODE_OFF)
nomPmBlocksize 1024 (NOM_PM_BLKSIZE_2_10)
operationalState 1 (ENABLED)
remoteBlockingState 1 (REMOTELY_UNBLOCKED)
reservedBy Aal2Sp=1,Aal2Ap=b072,Aal2PathDistributionUnit=b072
timerCu 10
userLabel Aal2PathVccTp b072a1
vclTpId AtmPort=MS-18-1-11,VplTp=vp1,VpcTp=1,VclTp=vc39
==================================================================================
===============================
Total: 2 MOs