2. 77. A machine tool in which abrasive wheel is used as cutting tool to obtain Is very
smooth finish.
a. Drill c. Planer
b. Grinder d. Shaper
3. 1. Heating above the transformation range, usually 1300F to 1350F, and cooling slowly
to soften the metal and increase in machining.
a. Annealing c. Normalizing
b. Hardening d. Tempering
4. 6. A machine tool used for producing holes in metal by the use of a cutting too called
drill.
a. Brass c. Iron
b. Bronze d. Tin
a. Brass c. Iron
b. Bronze d. Tin
9. 27. An operation of sizing and finishing a hole by means of a cutting too having several
cutting edges.
c. Turning
a. Notching d. Reaming
b. Piercing
10. 29. The operation of enlarging a hole by means of an adjustable cutting tool with only
one cutting edge.
a. Drilling c. Milling
b. Broaching d. Boring
11. 30. An imaginary circle passing through the pointsat which the teeth of the meshing
gears contact each other.
14. 40. The operation of cooling a heated piece of work rapidly by dipping it in water,
brine or oil.
c. Normalizing
a. Quenching d. Annealing
b. Tempering
15. 41. A method used in softening a piece of metal that istoo hard to machine and is done
by heating steel slowly above the usual hardening temperature, keeping it at the heat
for ½ to 2 hours, then cooling slowly, preferably in a furnace
a. Broaching c. Normalizing
b. Queching d. Annealing
16. 42. The total permissible variation in the size of a dimension; the difference the
limits of size.
a. Allowance c. Variance
b. Tolerance d. Interface
17. 49. A machine tool which is very similar to a shaper except that the ram reciprocates
vertically rather than horizontally.
a. Lathe c. Planer
b. Grinder d. Slotter
18. 53. A tool which when pressed into a finished holein a piece of work, provides centers
in which the piece may be turns or otherwise machined.
a. Mash c. Mandrel
b. Butt d. Wobble
19. 57. A gripping device with two or more adjustable jaws set radially.
a. Chuck c. Tailstock
b. Carriage d. Fan
20. 61. The process of heating a piece of steel to a temperature within or above critical
range and cooling rapidly.
a. Normalizing c. Annealing
b. Hardening d. Tempering
a. Radiometer c. Spectrometer
b. Profilometer d. Micrometer
22. 78. It is used to produce a variety of surfaces by using a circular-type cutter with
multiple teeth.
24. 90. In general the design stress and factor of safety are related as follows:
a. Chromium c. Brass
b. Bronze d. Aluminum
MD2
26. 2. It is used to produce a variety of surfaces by
using a circular type cutter with multiple teeth.
a. Manganese c. Tungsten
b. Carbon d. Sulfur
a. Normalizing c. Annealing
b. Quenching d. Squeezing
a. Seal c. Teflon
b. Packing d. Graphite
a. Quenching c. Annealing
b. Tempering d. Forming
35. 19. The total deformation measured in the
direction of the line of stress.
a. Flexure c. Elasticity
b. Stress d. Rigidity
a. Stress c. Strain
b. Strength d. Elasticity
a. Austenite c. Manganese
b. Mercury d. Martensite
a. Mash c. Wobble
b. Core d. Torch
a. Hematite c. Sulfurite
b. Magnetite d. Siderite
44. 47. A welding operation in which a non-ferrous
filler metal melts at a temperature below that
of the metal joined but is heated above 450C.
a. Carbon c. Phosphorous
b. Manganese d. Sulfur
a. 11 to 15 KW c. 7.5 to 10 KW
b. 16 to 21 KW d. 22 to 30 KW
a. 7.5 kW c. 15 kW
b. 11 kW d. 22 Kw
MD3
51. 4. The process of working metals by the
application of sudden blows or by steady
pressure.
a. Casting c. Forging
b. Turning d. Rolling
a. Hyper-Eutectoid c. Lead
a. Piezometer c. Barometer
b. Hydrometer d. Odometer
a. Monel c. Solder
b. Alloy d. Hastalloy
a. Carburizing c. Martempering
b. Normalizing d. Hardening
a. 3 mm c. 7 mm
b. 6 mm d. 4 mm
59. 62. Manganese steel standard designation is SAE ______.
a. 8XXX c. 12XX
b. 10XX d. 13XX
62. 95. Choose the one that will have highest cutting speed:
a. Aluminum c. Bronze
b. Aluminum d. Brass
a. Carbon c. Manganese
b. Silicon d. Tungsten
66. 82. In powder metallurgy the process of heating the cold pressed
metal powder is called:
a. Deposition c. Sintering
b. Granulation d. Precipitation
67. 69. Cast iron flywheels are commonly designed with factor of
safety of:
a. 9 to 12
b. 8 to 11
d. 7 to 10
c. 10 to 13
70. 44. In the color coding of pipe, the color for a pipeline of
water is:
a. Hardness c. Ductility
a. Elasticity c. Brittleness
b. Ductility d. Plasticity
a. Hyper-Eutectoid c. Lead
a. Flywheel c. Shaft
b. Governor d. Puncher
a. Martensite c. Austenite
a. Austenite c. Hyper-eutectoid
b. Solidus d. Eutectoid
a. Steel c. Aluminum
a. Creep c. Resilience
a. 0.02% c. 0.63%
b. 0.30% d. 0.80%
a. Impurity c. Slip
a. Alignment of drive
b. Lowering of drive
a. Axis of load
b. Minimum cross-section
a. Austenite c. Hyper-eutectoid
b. Solidus d. Eutectoid
a. 3 c. 5
b. 4 d. 6
a. 2.5 Hp c. 4.0 Hp
b. 3.0 Hp d. 5.0 Hp
a. Elastic c. Brittle
b. Plastic d. Malleable