06bCriteriainVesselDesign 2 PDF
06bCriteriainVesselDesign 2 PDF
net/publication/295857823
CITATIONS READS
0 1,466
1 author:
Abdul Wahid
University of Indonesia
67 PUBLICATIONS 72 CITATIONS
SEE PROFILE
Some of the authors of this publication are also working on these related projects:
Synthesis of Renewable Diesel from Palm Oil and Jatropha Curcas Oil through Hydrodeoxygenation using NiMo/Zal View project
All content following this page was uploaded by Abdul Wahid on 25 February 2016.
2
Program Studi Teknologi Bioproses
Departemen Teknik Kimia
Fakultas Teknik – Universitas Indonesia
Depok 2014
Bentuk Bejana
Analisis Tegangan (Stress Analysis)
• ANALISIS TEGANGAN adalah penentuan hubungan
antara gaya eksternal yang diterapkan pada bejana dan
tegangannya
• Seorang perancang harus benar-benar memperhatikan:
– Jenis beban, dan
– Bagaimana beban itu berhubungan dengan bejana secara
keseluruhan
• Apakah efeknya lama atau singkat?
• Lokal atau menyeluruh?
3 Faktor Penting
• Bagaimana tegangan-tegangan ini dipahami dan
digabungkan:
– Apakah berpengaruh secara signifikan terhadap keselamatan
bejana
– Berapakah tegangan maksimum yang diijinkan
Ditentukan oleh:
1. Teori kekuatan/kegagalan yang digunakan
2. Jenis dan kategori beban
3. Tegangan yang ada pada bejana
Membrane Stress Analysis
• Ketebalan dinding bejana adalah kecil sehingga dianggap
sebagai “membrane”
• Tegangan yang ada pada bejana juga disebut “membrane
stress”
• Ada tiga tegangan:
1. Tegangan longitudinal/meridional (x)
2. Tegangan circumferential/latidudinal ()
3. Tegangan radial (r)
KEGAGALAN (FAILURE)
Kegagalan
Kriteria desain vessel/ bejana berhubungan
dengan beberapa peristiwa yang Adapun penyebab kegagalan suatu vessel/
menyebabkan kegagalan pada perancangan bejana adalah sebagai berikut:
alat khususnya vessel/ bejana.
P
f
a
Modulus Elastisitas
Pembengkokan suatu
material memiliki
hubungan proporsional
dengan modulus elastis
& momen inersia suatu
material.
Disebabkan tegangan yang berlebihan pada suhu biasa (ambient) atau suhu rendah
(sub freezing temp).
Low alloy steel (2¼ % Cr, 1 % Mo) sangat sensitif terhadap temper embrittlement.
Jika tidak terjadi korosi maka kerusakan biasanya disebabkan oleh 2 faktor, yaitu:
Creep Test Dilakukan untuk mempelajari creep characteristics dari sebuah material
For steels at ambient temperature EY = 200,000 N/mm2 , and equation 13.71 with
a factor of safety of 12 gives
Weight Loads
1. The vessel shell;
2. The vessel fittings: manways, nozzles;
3. Internal fittings: plates (plus the fluid on the plates); heating and cooling
coils;
4. External fittings: ladders, platforms, piping;
5. Auxiliary equipment that is not self-supported; condensers, agitators;
6. Insulation;
7. The weight of liquid to fill the vessel. The vessel will be filled with water
for the hydraulic pressure test and may fill with process liquid due to
misoperation
Weight Loads
Weight Loads
Wind Loads (Tall Vessels)
The term (ae/g) is called the seismic constant, Ce, and is a functionof
thenatural period of vibration of the vessel and the severity of the
earthquake
Eccentric Loads (Tall Vessels)
Contoh 13.2
• Make a preliminary estimate of the plate thickness required for the
distillation column specified here:
– Height, between tangent lines: 50m
– Diameter: 2m
– Hemispherical head
– Skirt support, height: 3m
– 100 sieve plates, equally spaced
– Insulation, mineral wool: 75mm thick
– Material of construction, stainless steel, maximum allowable stress:
135N/mm2 at design temperature 200 oC
– Operating pressure 10 bar (absolute)
– Vessel to be fully radiographed (joint efficiency 1)
– Process service Gasoline debutanizer.
Solusi
• Brownell & Young, EH., “Process Equipment Design”, John
Wiley & Sons Inc, New York, 1959.
• Towler, G. and Sinnott, R. 2008. Chemical Engineering Design:
Principles, Practice and Economics of Plant and Process
Design. Elsevier
• Moss, Dennis. 2004. Pressure Vessel Design Manual. Third
Edition. Elsevier