p/n 069-2005-003
SERVICE MANUAL
ATTENTION:
WARRANTY SERVICE PROCEDURES
Warranty field service of the Passport PD-150 will be to the Module or PCB Assy. level.
Non-Warranty repairs of course can be to the component level at the Service Center’s
discretion. Please note for non-warranty repairs that all parts marked “REF” in the Parts
List will need to be sourced from suppliers other than FMIC.
Fender Musical Instruments Corporation, 8860 East Chaparral Road Suite 100 Scottsdale, AZ 85250
Issued: June, 2007
2
®
PASSPORT PD-150
(This is the model name for warranty claims)
IMPORTANT NOTICE
Copyright © 2007 FMIC. All rights reserved. All specifications are subject to change without no-
information contained herein is CONFIDENTIAL tice. This information and any copies produced
and PROPRIETARY and is the property of Fend- electronically or otherwise must be surrendered
er® Musical Instruments Corporation. It is not to upon demand of Fender® Musical Instruments
be sold or assigned to another party and is dis- Corporation.
closed solely for use by Fender Authorized
Service Centers for purposes of product service Parts marked with two asterisks (**) indicate the
and maintenance. All information is not to be dis- required use of that specific part. This is neces-
closed to others without the expressed permission sary for RELIABILITY and SAFETY requirements.
of Fender® Musical Instruments Corporation. All DO NOT USE A SUBSTITUTE!
SPECIFICATIONS
Model Name: PASSPORT PD-150
Release Number: PR483
Part Number: (120V, 60Hz) US: 069-2005-003
(120V, 60 Hz) DS: 069-2005-903
(240V, 50 Hz) AUS: 069-2005-033
(230V, 50 Hz) UK: 069-2005-043
(230V, 50 Hz) EUR: 069-2005-063
(100V, 50 Hz) JPN: 069-2005-073
Frequency Response: 30 Hz to 20 kHz ± 1 dB (at speaker output)
30 Hz to 20 kHz ± 1 dB (at send output)
Distortion: < 0.1%, 20 Hz to 20 kHz, 1dB below rated output
Signal to Noise Ratio: > 80 dB @ 1W, “A” WTD
Power Output: 75W/ch continuous average power, 8Ω, both channels driven with
THD <1%
Input Impedance:
(Channels 1, 2, 3 XLR and 1/4”) “Mic” switch position: 2 kΩ
“Line” switch position: 66 kΩ
(Phono and Stereo Channel 1/4”) 78 kΩ
Max. Input Level: Mic: -7 dBu
Line: 30 dBu
Stereo: 26 dBu
Return Input Impedance: 47kΩ
Fuse type: T4AH, 250V
Passport System: Width: 610 mm (24 in.)
Height: 541 mm (18 in.)
Depth: 254 mm (10 in.)
Weight: 15.91 kgs (35 lbs)
Speakers: Width: 245 mm (9.65 in.)
Height: 439 mm (17.5 in.)
Depth: 241 mm (9.5 in.)
Weight: 4.08 kgs (9.0 lbs)
Power Tower: Width: 254 mm (10 in.)
Height: 451 mm (18 in.)
Depth: 178 mm (7 in.)
Weight: 6.80 kgs (15.00 lbs)
Tower Footprint: 241 x 298 mm (9.5 x 11.75 in.)
Microphone: Dynamic Cardioid, balanced
Microphone Cable: XL -Male to XL-Female, 6 m (20 feet)
Speaker Cables: 1/4 in. to 1/4 in., 9 m (30 feet)
SERVICE NOTES
The following describes the procedure to dismantle B3. Unscrew nine M3 machine screws from the
the PD-150 Cabinets. mixer PCB assembly.
B4. Detach all connectors.
STEP A: PD-150 CABINET
B5. The procedure is completed.
A1. Unscrew two M4 machine screws on each of
the left and right hatches on either side of the
unit (8 total). STEP C: PD150 DSP REVERB PCB
A2. Unscrew two M3 pan-head machine screws C1. Detach all connectors.
on the handle cover and detach it. C2. The procedure is completed.
A3. Place the unit upside down. Unscrew eight M4
self-tapping screws off the foot standers.
STEP D: PD150 INPUT PCB
A4. Detach the foot standers. There are six M3
D1. Unscrew six screws and nuts from the front
self-tapping screws in the middle portion.
panel.
A5. Unscrew three M3 self-tapping screws located
D2. Detach all connectors.
on the right-hand-side.
A6. Place the unit in the normal position. D3. The procedure is completed.
A11. Unscrew three M3 self-tapping screws on left E3. The procedure is completed.
and right side panels (6 total) of the tower
metal assembly. STEP F: PD150 SMPS PCB
A12. Unscrew eight M2.6 and eight M3 self-tapping F1. Unscrew three screws from the front panel.
screws (three on top of front panel, three on
F2. Detach all wiring and connectors.
top of rear panel, and two on metal cover).
F3. Unscrew six screws from the top cabinet of
A13. Detach the left and right metal side panels.
the SMPS.
A14. Detach the top metal cover.
F4. Unscrew three screws from the bottom cabi-
A16. Unscrew seven outer M3 self-tapping screws nets of the SMPS.
on the rear panel.
F5. Detach the spacer from the wiring of the
A17. Detach all connectors. SMPS.
A18. The procedure is completed. F6. Unscrew the earthing M4 nut.
F7. Detach the mains connector from the AC inlet.
STEP B: PD150 MIXER PCB F8. Unscrew five screws from the SMPS PCB as-
B1. Detach 24 knobs and their nuts. sembly
B2. Detach the Reverb PCB assembly. F9. The procedure is completed.
5
®
PASSPORT PD-150
(This is the model name for warranty claims)
Parts marked with a single asterisk (*) in the Part contact the FMIC Customer Service Department to
Lists are not field replaceable. If a failure due to order the complete PCB Assembly.
one of these components is detected, please
CIRCUIT DESCRIPTION
This section provides concise information about new signals. The main signals are then routed to a pan
or unusual circuitry designs incorporated into this circuit. Here the main signal is split between the left
amplifier model. The purpose is to aid the service and right channel signal bus. Channel three also
technician by providing insight into the design areas has an additional input via a pair of RCA connectors
most likely to become obstacles in troubleshooting. where the signals are summed into mono which
Information is focused for its effective use while may be used as an auxiliary audio signal input.
maintaining the security of Fender® proprietary
information wherever possible. The stereo mixer section consists of a stereo pair
inputs with RCA and 1/4" stereo phone jack con-
The PD-150 consists of the following modules. nections. This circuit consists of an auto-pad level
1. Mixer Section control, low frequency and high frequency tone con-
2. Digital Reverb Section trols, Rev/Aux send control and balance control with
3. Signal Processor Circuit and System EQ Circuit signals feeding the left and right audio bus. The
4. Power Amplifier audio bus is connected to three FETs that perform
5. Switch Mode Power Supply Unit (SMPSU) ducking of the signals on the bus with the exception
of channel one which is the drive circuit for the VIP
ducking circuit. This function is provided by U1B.
The Mixer PCB module Bus signals are buffered by U8A/B and drive the
tape output connections and drive the main left and
The mixer section is mainly made up of operational right master level control circuitry made up of
amplifiers as gain stages and therefore a technical U9A/B. The Rev/Aux signals are buffered by U12B
description will not be used here. Following is a ba- and feed the mono aux send output. Main left and
sic circuit description to familiarize you with the right level controls are auto-pad configuration and
layout of the circuit. drive the speaker EQ circuitry made up of U10A/B.
Note: Channel 1 Mic/Line reverb function will be af-
The Mic/Line section is made up of 3 microphone / fected by VIP control making announcements on
line inputs each with a first stage preamplifier for Channel 1 dry.
balanced or unbalanced inputs (locate on the mixer
board). Line inputs can operate as either balanced The mixer board also contains part of the signal
or unbalanced if TRS or TR 1/4" jacks are used re- processor circuit and the system EQ circuit for the
spectively. Gain selection of 1dB/+30dB is made by power amplifier. These circuits are an integral part
switching a different value resistor in the input of the power amplifier and appear after the return
stage. At this point on channel one, the signal is signal path.
picked off for the VIP control ducking circuit made
up of U1B. These circuits will all be discussed later in this doc-
ument.
After the input stage there is one knob for contour
control, followed by an auto-pad level control where
the signal splits off into the rev/aux bus and main
6
®
PASSPORT PD-150
(This is the model name for warranty claims)
The DSP Reverb PCB Module directly drives the biased gates of lateral power
FETs Q204 and Q205.
The DSP Reverb PCB module receives the input
REV/AUX signals at pin 4 of connector CN401. The Speaker short circuit protection is provided by
DSP Reverb’s IC’s consist of U404 (AL1101 ADC), U203B. This is accomplished when the output is
U405 (AL1201 DAC), and U406 (AL3201B). The shorted to ground, the normal differential signal ap-
outputs from U405 are fed to U402B and then buf- plied to U203B is absent at the negative terminal
fered by U402A before feeding back to pin 6 of CN while at the same time, the second stage is now
401. forced into open loop gain. The drive signal is inte-
grated into C207 forcing a positive voltage at the
output of U203 that pulls the gate of FET Q203 into
Signal Processor & System EQ Circuit
conduction from its previous negative bias off point,
nulling the output of U202A. With the output of
The signal processor is partially located on the mix-
U202A minimized the output current of the amplifier
er board but is an integral part of the power
is minimized until the short is removed. At this time,
amplifier section. The operation of this circuit is per-
C207 will discharge allowing normal operation of
formed by filtering the signal from U11A/B which
the amplifier. Note: Some small DC offset will be
drives the bases of Q5 and Q7 to control the vol-
present when the amplifier is in the short circuit pro-
tage level at FETs Q4 and Q6 respectively. This in
tect mode.
turn changes the filter characteristics of circuits
which at low levels boosts the low and high fre-
The power amplifier board also provides the ±15v
quencies of the signal. At high signal levels with the
for the Mixer and DSP reverb boards as well as the
gate voltages approaching or at 0v, the circuit low-
supply for the SMPSU FAN and the LED PCB
ers the boost of the low frequencies in response.
which indicated power and thermal protection mod-
This circuit is post aux return and therefore does
es. The power amplifier board is also connected to
not modify the response of the signal at the aux
the GM type fuse holder and aux DC power input
send outputs.
connector.
to the rails before you open the set for service to Service Notes on Changes and Upgrades
get an indication of a possible power supply fault as
it is connected to the rail output. Do not short these A 0.01uF mylar film capacitor has been added to
terminals! the VIP ducking circuit to prevent a slight hum that
may be heard as an artifact at the tail of the ducking
The SMPSU incorporates protection circuits other action. This was mainly detected on UL voltage set-
than the fuses including over current protection. All tings. This capacitor is added at the junction of R18
parts contained in the SMPSU should be consi- (1Mega ohm) and D16 and the Source (Ground) of
dered to be safety parts and should be replaced FET Q3 (J112). This modification should be per-
with only exact where service can be provided by formed on individual units that are listed below by
properly licensed and trained repair technicians. S/N. All other UL units have been modified by the
This includes the dust filter as well as it has a fire
factory.
hazard rating. Please be aware that voltages con-
tained in this module are deadly!!
8
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
9
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
10
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
11
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
12
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
13
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
14
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
17
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
18
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
19
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
21
®
PASSPORT PD-150
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
22
®
PASSPORT PD-150
(This is the model name for warranty claims)
8
13 0dB C1 C8 LEVEL MIC/LINE1
R1 R4 EQ VR18A R93
1k 33k 2u2/50V U1A C5 153 C10 R14 VR2A R20 R82 R86 2
R10 VR1A R13 100KB W/CC 33k
2 3 LM833 0.47u/50V 39k 1u/50V 12k 100KB 100k 110k 100k
100KB W/CC 39k R94
1 3 1
33k
2 3 1 1
2 R12 C83 102 2 C11 R91 C52
82k R90 -15V C54 C55
R2 R5 C2 1n 27p 2 1k 27p
-15V 1k
4
2u2/50V PAN VR5A C51 C53 472 472
4
1k 33k R83
4
3 R8 3 100KB W/CC 0.47u/50V 0.47u/50V
-15V 33k 6k8 R92 R95
U2A 6 2 VR20A
TP11 SS2214RG9 -15V 100k 100k
2 TL072 C9 27p 7 1 100KB W/CC
SW1B
4
1 4 +30dB C4 1 5 4 VR5B C49 R143 3 1 3
D3 100p 3 U2B VR4A 100KB W/CC 0.47u/50V R88 U9A SYSTEM EQ 2
1N4148 PAN 33k
6 TL072 3 100KB 5 2 1k TL072
5 0dB -15V
6 1 C80
8
R21 100k R84 110k
4
C6 Q11 2 3 27p
8
D15 REV/AUX +15V
D4 1u/50V MPSA56 U8A
C3 1N4148 +15V 1N4148
R3 R6 100p R7 1 2
1k 1k TL072
33k R11 1
8
10K D 3
PJ1 PJ6-09-5 R17 +15V U10A
1 CN4 -15V R85 RIGHT
1
2
3
1M R87
5 VIP VR3A
100KB
CON3 G Q3 R22 6k8 100k VR19A
TP13 R96 TL072
4 -15V +15V 3 1 J112 470
8
1
2
3
R16 103 +15V
8 2 CON3 2M2 R23 33k
470 2
LINE 1 CN604B C84 D
WE2 102 R15 D16 R18 U8B C57 C59 C60
CN1 1k 1N4148 1M G Q2 R89 C56 27p C58 472
1 TL072 R144 472
CON15 TO WIRE DOCKING 6 J112 6 1k 0.47u/50V 33k 0.47u/50V R97 R99
2 U1B VR20B
7 S C50 7 6 100k 100k
1 LM833 100KB W/CC
5 0.47u/50V 5 7
2 D5 C12
D6 5 4 6
3 SS2214RG9 4u7/50V R24 U9B
4 1N4148 1N4148 SYSTEM EQ 5
4 470
5 SW2A 1 +30dB R19 D TL072
5 +15V -15V R33 C18 U10B
2 1M C81
6 12k 152 Q1 TL072
G 6 27p
7 +15V J112
3 C19 7
8
8
R25 R28 0dB C13 153 LEVEL MIC/LINE2 S VR ROTATION CONFIGURATION 5
9 U3A EQ R40
1k 33k 2u2/50V C17 R34 R36 C22 R37 VR7A 82k
10 VR6A R38
3 LM833 0.47u/50V 39k 39k 1u/50V 12k 100KB MIN(CCW) PINS 2/5 SHORTED TO 1/4
11 100KB W/CC 100k TP14
1
12
2 3 1 3 1 1 CENTER PINS 2/5 AT CENTER
13 R35 C23
2 C20 102 2
14 82k 1n 27p
R26 R29 C14 2 MAX(CW) PINS 2/5 SHORTED TO 3/6
15 -15V PAN
2u2/50V R32 VR9A C62
4
1k 33k -15V
4
TO 33k 3 100KB W/CC R101 27p
-15V C61
TP15
4
8
D8 TL072 12k
R27 R30 C15 R31 1
8
1
TO WIRE DOCKING 3 C30 Q4 G TO LEFT PA
R49 C24 153 LEVEL MIC/LINE3 D START = D1 J112
R43 0dB EQ
2u2/50V U3B C28 C33 VR11A R60 D END = D16 S R109 CN5
1k 33k R54 VR10A R56 R57 R58 2M2
6 5 LM833 0.47u/50V 1u/50V 100KB 82k CON3
39k 100KB W/CC 39k 12k 100k
7
C66 TP1 GND 1
6 3 1 3 1 1 VR START = VR1 Q5 CN8 C69
R55 4u7/50V 2
TP12 2 C31 102 2 C34 VR END = VR22 MPSA56 WF8 27p
82k 1 3
C25 1n 27p 2
R44 R50 R51 -15V PAN 2
2u2/50V VR13A
1k 33k 33k 3 R111
4
7 3 100KB W/CC TO RIGHT PA
39k
6 TP2
SS2214RG9
2 C32 27p 7 4 VR13B
SW3B
8 4 +30dB C26 1 5 100KB W/CC 6
D11 100p 3 3 5 7
LEFT CHANNEL BUS
RIGHT CHANNEL BUS
AUX CHANNEL BUS
8
TL072
R46 D12 R116
PJ3 C27 1N4148 +15V R59
PJ6-09-5 1 1k R52 REV/AUX 1 R61 12k
100p 100k R112
5 R45 33k 82k C70
4 1k R113 222 12k
7 R62 R122 R124 6k8 C74
C42 R73 82k 100k 56k 222
8
223 27k
-15V +15V
R114
LINE 3 C78 C79
-15V C72
C71
3k3
TP16
LEVEL/STEREO C43 27p 27p 0.56u/50V
R47 C35 C39 EQ/LOW 27p R76 R77 R121 R120 1u/50V R115
9 82K 1u/50V R67 VR14A 1u/50V R69 VR16A 100k 82k 6k8 110k R117 R118 6k8 R136
27k 100KB 27k 100KB W/CC 2M2 1M
1 3 1 470 PJ5 PJ6-09-3
-15V
3 1 VR17A D 5
-15V
4
4
2 R123 1
R48
4
D13 C37 R141 3 2 S Q6 R119
82K 39k 2M2
1N4148 27p EQ/HI 3 C41 R71 39k 2 1 6 J112 AUX SEND
2 102 27k 1 C75 3 7 MONO
-15V 1n U12A C73
1 VR15A 2 3 4 VR17B 0.47u/50V 5 Q7
3 100KB W/CC U7A 100KB W/CC TL072 U12B 4u7/50V MPSA56
U6A BAL
8
TL072 TL072
1 5 PJ6
8
TL072 +15V
R78
8
+15V 82k PJ6-09-5
R63 6 AUX RET
+15V R125 R137
10k STEREO
PJ4 PJ6-09-5 R74 R79 82k 10k
8 C44 100k 8
7 223 27k 7
4 4
5 5
C36 LEVEL/STEREO EQ/LOW
1 R68 C40 1
R64 1u/50V VR14B R70 VR16B R126 R138
27k 1u/50V C46 27p 82k
10k 100KB 27k 100KB W/CC 10k
STEREO 6
4 6 4
5 5 R127 FOOT
82k SWITCH
D14 C38 R142 5
R66 1N4148
10k 27p 6 C45 39k 6 4
R72 R145
12 6 EQ/HI 102 7 1
-15V 27k 100k
7 5 1n 5 PJ7
U7B R132 R133 R134
5 VR15B PJ6-09-3
1M 1M 1M R135
MONO STEREO
U6B 100KB W/CC
4
TL072
TP17 FS 1M
R139
100k
TL072
3 1 -15V
NC 5 5 +15V -15V 1
4 4 REV IN 2
3 3 C86 C85 C77
R65 2 SW4 D D D C82 104 47u/50V
R75 R80 +15V 2 2 +15V 104
10k SS2214RG9 TP18 G G G 1u/50V C76 CN6
10k 10k 1 1
11 47u/50V +15V CON2
1 CN7 R128 R129 R130 Q8 Q9 Q10
S S S
2 CON2 82k 10k 39k
3 VR22A CN2 CN2 J112 J112 J112 POWER IN
R81 REV OUT
100KB 3 CON5 WF5
82k
TO START GROUND VR21A
REV/AUX 2 2 100KB
R140 GND
3R3 2W
1 MASTER REV
1 REVERB
INPUT GROUND OUTPUT GROUND
PCB TP19
TP20
2
Mixer PCB Copper Side PASSPORT
Mixer Section PCB
3
RJ1A
RCA HSP-206V-03 L
14
TAPE OUT 15
13
RJ1B
RCA HSP-206V-03 R
2 MJ1
+
MIC 1 3
SVP561P-R -
G 3
1 1
CN1
WF15
4
1
2
3
MJ2 4
2
5
+ 6
MIC 2 5 TO
SVP561P-R - 7
3 MIX
G 8
AMP
9
1
10
11
12
13
14
15
6
2 MJ3
+
MIC 3 7
SVP561P-R -
3
G
1 8
RJ1C
RCA HSP-206V-03 9
EXTRA MUSIC
10
RJ1D
RCA HSP-206V-03
RJ1E
RCA HSP-206V-03 12
RJ1F
RCA HSP-206V-03 11
PASSPORT
R
4
1u
50V C602
CN602
PWR/OUT
1k5
240
U601 CN601
C601 PWR/IN
LM317HV
IN
100n
O
R601
R602
ADJ C603
1000u/63V
1u
C602 50V
CN602
PWR/OUT
1k5
240
CN601 U601
PWR/IN C601
LM317HV
IN
100n
O
R601
R602
C603 ADJ
1000u/63V
PASSPORT
RCA/XLR/REG PCB
5
R403
2.2K
2 U403B
- R402
C401 1 6 C403 U404 +5V
- R406
3 2.2K 7 1 16
+ INL+ INR+
5 220R 2 15
+ 10uF/25V INL- INR-
10uF/25V U401A +5V 3 14
AGND MID C414
NJM2068 NJM2068 R408 4 13 C415
REF+ VA 0.1uF
1K C405 5 12 0.1uF
R404 REF- AGND
0.1uF 6 11
VD DGND
2.2K 7 10
C404 DGND DOUT
C406 8 9
R405 4700pF FORMAT WDCLK
0.1uF
R401 2.2K AL1101 ADC
100K U403A
2 C402 +5V
- R407
1 +5V
3 220R
+ 10uF/25V
NJM2068 TP23 R416 R414 R415
10K 10R
XL401 10K
U406
12.288MHz 1 16
Dig Out DigIn
2 15
Int/Ext Vdd C416 C417
3 14
Xtal In Bypass 0.1uF 0.1uF
4 13
Xtal Out Gnd
CN401 5 12
Prog0/SData Reset
AUDIO OUT 6 11
6 R417 Prog1/SClk SysClk
AGND 7 10
5 1K Prog2 BitClk
AUDIO IN 8 9
4 Prog3 WordClk C420
+15V
3 R409 1uF/50V
AGND AL3201B
2 4.7K
-15V
1 R418 R419
6
6PIN 10K 10K
U402A
C407 220pF TP24
3
+ R421
1 +5V
2 U402B R410 10K
- 10K
C430 6 C410
-
10uF/25V NJM2068 7 C408 470pF 10uF/25V
5 R420
+ 10K
R411 C411 U405 +5V
NJM2068 10K 10uF/25V 1 16
C409 OUTL- OUTR-
R412 2 15
220pF OUTL+ OUTR+
4.7K 3 14
AGND MID
R413 C412 4 13
REF+ VA C418 C419
220 0.1uF 5 12
REF- AGND 0.1uF 0.1uF
6 11
VD DGND
C413 7 10
DIN DEM
+15V 0.1uF 8 9
FORMAT WDCLK
8
8
8
CN402 78L05
0.1uF U401C 0.1uF U402C 0.1uF U403C 3 1
2 Vin Vout
1
GND
4
4
4
C434 C433
C431
2
0.1uF
0.1uF 0.1uF 0.1uF 10uF/25V
0.1uF
C429 -15V
47uF/25V
CN205
GR/RED GR/RED
2751-6 LED REV:D REV:D 2751-6 LED
PASSPORT
Reverb Section / LED PCB
7
KS-1554 TP2
G301 GAS ARRESTER
FB307 L302
TP1 D FB 360uH
D301 R312 FB303
T303
51 FB
NTC301 KBU6J 8 G S KSF1689
2
SCK055 FB301 D308
FB304 C318 FEP 16GT
Z304 Q301 FB 470p 1KV
FB
T302 18V IRF840 C320
C305 7
R302 KS-851N 3 10000u/63V
330u/200V 100K 1/2W R313 R318 FB308
1000P 400V SW302 1K R317 47 2W FB CN203
1000P 400V AC SELECTOR SW 100 2W CON4
C324 C325 C316
220V 110V Z303
100n 1
18V FB309
1 2
C306 9 7
3
330u/200V R303 FB 4
100K 1/2W
D309
R319 TO
FB302 4 FEP 16GT
D306 12 8 47 2W POWER
1 6 FB
UF 4006 AMP
C321
Q302
T307 FB310 10000u/63V
IRF840
EPCOS 2X15mH D305 D FB
FB305
16
3 4 D302 R314 C319 KS-1554
1N4148 FB D307 C317
UF 4003 6 51 G S 470p 1KV 360uH
UF 4006 100p 1KV NC 1
1000P 400V
C327 KSF1689
C326
Z302
C307 18V
5 CN201 2
1000P 400V 100u/50V 4
R315 CON2 1
FB306 NC
1K
15
C302 220n 275V ac FB
8
EPCOS 2X15mH RF1 GROUND GROUND
7
6
U301 CN603B 1 ANTENNA
3842 R316 CON2 2
0.22 3W TO WIRE DOCKING R320
R301 470K 1/2W
O/P
VCC
220n 275V ac C308 2K 1W
C301 R321
470p 1 3
COMP ISEN 39K
R311 R324
R304 2 C315 47K
VFB 220
100K 472
R322
CN301A
3
2
1
470
WF3 R START = R301
VREF
RT/CT
GND
C323
R END = R325 R323
R310 1u/50V
47K TP301
K
1
2
3
CN301B 470
R305 C START = C301 T START = T301 TP1K
8
4
5
CON3
1M C END = C327 T END = T306
Z305
SW301 R
D START = D301 FB START = FB301 12V
C313
SW 2P2T D END = D309 FB END = FB302 U303
472 C314 TL431
R306 222 R325
Z START = Z301 U START = U301
2K7
A
E
R307 R308 U302
L303 TP START END=TP301 22K CNY17-2
1K
G START END=G301
PASSPORT
SMPS PCB
9
Q START = Q201 TP START = TP201
Q END = Q209 TP END = TP202
1
2
33V CON2 R204
39K D END = D211
Q201
TP7 Z START = Z201
MPSA06 TP6 Z END = Z208
D201 +15V BOOTSTRAP R224 TP9
1N4148 3K3 2W
START GROUND
D205 CN201
R214 1N4148 D WF2
15K PJ201 PJ6-09-3
G Q204 1
2SK1058 4
R210 2
S 5
1K5 1
R215 Q203 D204 C209 R SPKR OUT
390 1N4148 224
J112
S D
R209 PJ202 PJ6-09-3
1 START GROUND
5K1 1% 2
_ Z202 C210 4
1 G R222 15V 47u/25V 5
3 3M3
+ U202A L SPKR OUT
LM833
Q202 G R218 D203
J112 3 2
56K 1N4148 R221 Vin Vout
D S 1M
ADJ
R212
C204 1K5
22u/16V 5 8 R602 R601
D202 C207 C208 + C602 U601 240 50
R208 R213 7
1
1 WF2
3 START GROUND
U201A
R206 R216
100K TL072
390
S
+15V
R207 G Q205
390 R217 R219 R220 Z203 C211 2SJ162
100K 47u/25V D
CN5 15K 1M 15V C226
WF3 10u/100V -42V F201 CN202
CN203
R WF4 10A WF4
3 R226
2 -15V BOOTSTRAP D206 4 1 -36V
3K3 2W C224
10
1 1N4148 3 2
100n
L 2 3
AUDIO IN C228 Z208 1 4 +36V
START GROUND
47u/25V 12V 1W F202
10A EXIT/DC
(OPTION)
1
TP4 2 CN204B
CON2(FAN)
CN204A
R247 WF2
+15V BOOTSTRAP
2
1
CON2
R239
390
TP10 LED
S G
R229
390 Q209
G
R240 Z205 C221 2SJ162 LED201
R242 R243 47u/25V
15K 100K 1M 15V D 209EGW
R
PASSPORT
Power Amp Section PCB
11
TP1 DC 300V
TP2 DC 42V
TP3 DC -42V
TP4
TP5
PASSPORT
Test Point Information
12
TP6
TP7
TP8 DC 42V
TP9 DC 8V
TP10 DC 15V
PASSPORT
Test Point Information
13
TP11
TP12
TP13
PASSPORT
Test Point Information
14
TP14
TP15
TP16
PASSPORT
Test Point Information
15
TP17
TP18
TP19 DC 15V
TP20 DC -15V
TP21 DC 15V
TP22 DC 5V
PASSPORT
Test Point Information
16
TP23
TP24
PASSPORT
Test Point Information
17
1000u/63V
ADJ
RCA/XLR CN1
C603 REG
R602
R601
O
CN601
100n
IN
Input PCB
LM317HV
C601
PWR/IN
CN601 U601
PCB
240
1k5
PWR/OUT
CN602
C602 50V
CN602 CN7
AUT_CH1 1u
GND
AF_CH1 white
GND black
GND CN605B CN604B
VCC
GND red
AF_CH2 balck CN1
GND
AUT_CH2
CN6 CN2
18
CN204
FAN
CN203 CN201
CN205
MIXER PCB
CN402
SMPS PCB
Wiring Diagram
REV:D 2751-6 LED
GR/RED
LED PCB
CN205
CN205 04/98
DUAL LED
LED201
Reverb
CN5 PCB CN401
PASSPORT
The following is the legend of the mating connections
PCB-P150D11+MIXE PCB-P150D11+RCA
1 GND 1 GND
2 MIC1+ 2 MIC1+
3 MIC1- 3 MIC1-
4 MIC2+ 4 MIC2+
5 MIC2- 5 MIC2-
6 MIC3+ 6 MIC3+
7 MIC3- 7 MIC3-
CN1 8 GND CN1 8 GND
9 RCA IN1 9 RCA IN1
10 RCA IN2 10 RCA IN2
11 STEREO R 11 STEREO R
12 STEREO L 12 STEREO L
13 TAPE OUT R 13 TAPE OUT R
14 TAPE OUT L 14 TAPE OUT L
15 GND 15 GND
PCB-P150D11+MIXE PCB-P150D21+DSPR
1 GND 1 GND
2 +15V 2 +15V
CN2 3 REV OUT CN401 3 REV OUT
4 REV IN 4 REV IN
5 FS 5 FS
PCB-P150D11+MIXE PCB-P150D11+PWRM
1 AUDIO OUT L 1 AUDIO IN L
CN5 2 GND CN5 2 GND
3 AUDIO OUT R 3 AUDIO IN R
PCB-P150D11+MIXE PCB-P150D11+PWRM
CN6 1 -15V CN6 1 -15V
2 +15V 2 +15V
PCB-P150D11+MIXE PCB-P150D11+SMPS
CN7 1 GND CN7 1 GND
2 GND 2 GND
PCB-P150D11+MIXE WIRELESS PCB
CN604B 1 AF_CH1 3 AF_CH1
2 GND 4 GND
PCB-P150D11+MIXE WIRELESS PCB
CN605B 1 AF_CH2 8 AF_CH2
2 GND 7 GND
PCB-P150D11+PWAM PCB-P150D11+LED
CN205 1 GND CN205 1 GND
2 +15V 2 +15V
PCB-P150D11+PWAM PCB-P150D11+REG
CN601 1 +42V CN601 1 +42V
2 GND 2 GND
PCB-P150D11+SMPS PCB-P150D11+PWRM
CN201 1 GND CN201 1 GND
2 GND 2 GND
PCB-P150D11+SMPS PCB-P150D21+PWRM
1 +42V 1 +42V
2 GND 2 GND
CN203 3 GND CN203 3 GND
4 -42V 4 -42V
PCB-P150D11+REG WIRELESS PCB
CN602 1 GND 5 GND
2 +8V 6 +8V
PASSPORT
Wiring Diagram
19
Mixer Board
VIP Ducking
RCA/XLR
Input Board
Gain Switch
CH1 PAN
Rev/Aux
Contour Level
Gain Switch
20
Right
R Speaker
Line1 Out
Line2
Reverb Board
Block Diagram
PASSPORT
NO. DESCRIPTION PART NO. QTY
1 SPEAKER ASSEMBLY SS-EF010C-SPK 2
2 TOWER HOUSING ASSEMBLY 1
3 GIG BAG 1497-2132+0 1
4 MICROPHONE 1525-1120+0 1
5 MIC CABLE 7010-8290+0 1
6 MIC CLIP 4133-9100+0 1
7 DSUT FILTER 9500-0900+0 1
D
10 12
3 10
11
10
9
8 6 10
9 12
7
2
10
B
10 10
13 15 C
17
10
17
14
18
16
1
21 19
20
10 Mixer Ass’y Exploded View
3
Latch Ass’y Exploded View
12
16
16 6 16
11 16
12 1
8 17
7
9 10
18
15 16
12 18
18 10
12
4
8 5
A
2
14
3
23
3
4
9
11
6
2 10
7 12
13
1 14
15
5
12
16
24
Tower Housing Ass’y Exploded View
NO. DESCRIPTION PART NO. QTY NO. DESCRIPTION PART NO. QTY
1 CONSOLE PD 150 4153-2701+0 2 21 SCREW B-TITE BH M4X14MM BZ CROSS 2954-4014+3000 6
2 FRONT PANEL EXPLODER 1 22 SCREW FLAT-CS M3X5MM BZ CROSS 2901-3005+3000 2
3 POWER EXPLODER 1 23 SCREW TAP-BT BH M2.6X6MM BZ CROSS 2934-2606+3000 2
4 SIDE PALTE-B 4133-9480+0 1 24 S-TITE 3X8 (BLK) 2944-3008+3000 9
5 HANDLE COVER 4153-2690+0 1 25 SCREW TAP-BT BH M3X6MM BZ CROSS 2944-3006+3000 12
6 PARTITION 4133-9450+0 1 26 SIDE PLATE-A 4133-9470+0 1
7 DOOR 4153-2750+0 1 27 METAL WASHER M3X0.5X8MM BZ 2600-3005+0803 10
8 LOCKER DOOE 4153-2760+0 1 28 FENDER BADGE PD150 4154-3831+0 2
9 F3X8MM SELF TAPPING 2954-3008+3000 4 29 SPRUE CAP (BLK) 4153-2812+0 2
10 HINGE 4153-2780+0 2 30 4X16MM PA 2910-4016+3000 2
11 COMPRESSION SPRING 4133-9560+0 1 31 SCREW S-TITE 4X16MM PH BLK ZINC 2940-4016+3000 8
12 FOOT STAND PD150 4153-2712+0 2 32 SPRING WASHER M4X0.8X6.5MM BZ 2607-4008+0653 8
13 SUPPORT RIB 4153-2720+0 1 33 METAL WASHER M4X0.8X10MM BZ 2600-4008+1003 8
14 HANDLE BKT 4132-4901+0 2 34 SPRING WASHER M3X0.9X5.5MM BZ 2670-3009+0553 3
15 GASKET – TOP PD150 4153-2862+1 1 35 HALO BUSHING 0813C 2113-9535+0 1
16 GASKET - HANDLE PD150 4153-2852+1 1
17 GASKET – BOTTOM PD150 4153-2872+1 1
18 LATCH LOCKER EXPLODER 4
19 TTS SCREW M2.6X8 BH 2944-2608+0000 8
20 SCREW TAP-C2 BH M4X10 BZ CROSS 2954-4010+3000 8
25
Packing Ass’y Exploded View
26