Bogotá, Colombia
INTRODUCCIÓN
Caída de presión
Todas las propiedades son uniformes en la sección transversal del flujo, con un
valor promedio (bulk average)
2
VELOCIDAD PROMEDIO
5
LA REGION DE ENTRADA
Flujo
completamente
desarrollado:
Región en donde
están desarrolladas
las zonas térmica e
hidrodinámica.
Lh
Los coeficientes de
fricción y convección
permanecen
constantes!
Lt
T Ts
A diferencia del perfil de velocidad que permanece constante para
cte
una sección transversal dada, el perfil de temperatura varía.
Ts Tm
6
FLUJO COMPLETAMENTE DESARROLLADO
80 ºC
Agua
10 ºC D=0,02 m
8 L/min
L=7m
ρ = 990,1 kg/m3
υ = 0,602 * 10-6 m2/s
10
EJERCICIO PROPUESTO
Se quiere calentar agua desde 10 hasta 80 ºC. El agua fluye
a razón de 8 L/min a través de un tubo de 2 cm de diámetro
interno y 7 m de largo. Podemos asumir flujo completamente
desarrollado?
80 ºC
Agua
10 ºC D=0,02 m
8 L/min
0,008/60 m3/s
L=7m = = 0,424 m/s Re = 14100
π (0,02)m /4
2
Temperatura de superficie:
14
FLUX DE CALOR CONSTANTE
Número de unidades de
transferencia, NTU
NUMERO DE UNIDADES DE
TRANSFERENCIA - NTU
La diferencia media logarítmica es una
representación de la diferencia de temperatura
promedio entre el fluido y la superficie:
∆Ti = Ts – Ti
∆Te = Ts – Te
17
DIFERENCIA MEDIA ARITMETICA DE
TEMPERATURA
Con:
18
CALENTAMIENTO DE AGUA EN UN TUBO
CON VAPOR
Entra agua a un tubo de cobre de 2,5 cm de ID de un intercambiador de calor a
15 ºC y 0,3 kg/s. Se calienta debido al contacto con vapor en proceso de
condensación a 120 ºC. Si el coeficiente de transferencia de calor promedio es
800 W/m2 ºC, determine la longitud requerida del tubo para calentar el agua
hasta 115 ºC.
19
CALENTAMIENTO DE AGUA EN UN TUBO
CON VAPOR
Entra agua a un tubo de cobre de 2,5 cm de ID de un intercambiador de calor a
15 ºC y 0,3 kg/s. Se calienta debido al contacto con vapor en proceso de
condensación a 120 ºC. Si el coeficiente de transferencia de calor promedio es
800 W/m2 ºC, determine la longitud requerida del tubo para calentar el agua
hasta 115 ºC.
20
CALENTAMIENTO DE AGUA EN UN TUBO
CON VAPOR
Entra agua a un tubo de cobre de 2,5 cm de ID de un intercambiador de calor a
15 ºC y 0,3 kg/s. Se calienta debido al contacto con vapor en proceso de
condensación a 120 ºC. Si el coeficiente de transferencia de calor promedio es
800 W/m2 ºC, determine la longitud requerida del tubo para calentar el agua
hasta 115 ºC.
21
CALENTAMIENTO DE AGUA EN UN TUBO
CON VAPOR
Entra agua a un tubo de cobre de 2,5 cm de ID de un intercambiador de calor a
15 ºC y 0,3 kg/s. Se calienta debido al contacto con vapor en proceso de
condensación a 120 ºC. Si el coeficiente de transferencia de calor promedio es
800 W/m2 ºC, determine la longitud requerida del tubo para calentar el agua
hasta 115 ºC.
2323
CAIDA DE PRESIÓN
Ley de Pouseuille:
2525
OTRAS GEOMETRIAS
2626
FLUJO ENTRE PLACAS ISOTERMAS
2727
FLUJO TURBULENTO EN TUBERIAS
2828
FLUJO DE ACEITE POR UNA TUBERÍA A
TRAVÉS DE UN LAGO
Fluye aceite a 20 ºC en una tubería de 30 cm de
diámetro con una velocidad promedio de 2 m/s.
Una sección de 200 m de longitud de la tubería
pasa por agua helada a 0 ºC. Mediciones indican
que la temperatura superficial de la tubería es
prácticamente 0 ºC. Descartando la resistencia
térmica del material de la tubería, determine:
La temperatura del aceite cuando la tubería
deja el lago.
La velocidad de transferencia de calor desde
el aceite.
La potencia de bombeo requerida
2929
FLUJO DE ACEITE POR UNA TUBERÍA A
TRAVÉS DE UN LAGO
3030
FLUJO DE ACEITE POR UNA TUBERÍA A
TRAVÉS DE UN LAGO
3131
FLUJO DE ACEITE POR UNA TUBERÍA A
TRAVÉS DE UN LAGO
3232
FLUJO DE ACEITE POR UNA TUBERÍA A
TRAVÉS DE UN LAGO
3333
FLUJO DE ACEITE POR UNA TUBERÍA A
TRAVÉS DE UN LAGO
3434
AGUA DE ENFRIAMIENTO PARA
CONDENSAR VAPOR
3535
AGUA DE ENFRIAMIENTO PARA
CONDENSAR VAPOR
3636
3
6
AGUA DE ENFRIAMIENTO PARA
CONDENSAR VAPOR
3737
3
7
AGUA DE ENFRIAMIENTO PARA
CONDENSAR VAPOR
3838
3
8
8-40 Water is to be heated from 10°C to 80°C as it flows through a 2-
cm-internal-diameter, 7-m-long tube. The tube is equipped with an
electric resistance heater, which provides uniform heating throughout
the surface of the tube. The outer surface of the heater is well
insulated, so that in steady operation all the heat generated in the
heater is transferred to the water in the tube. If the system is to
provide hot water at a rate of 8 L/min, determine the power rating of
the resistance heater. Also, estimate the inner surface temperature of
the pipe at the exit.
Propiedades a 45 C:
Propiedades a 45 C:
Reynolds:
Flujo
turbulento
Flujo
completamente
desarrollado
Propiedades a 45 C:
Nusselt h Te:
8.43 Consider an air solar collector that is 1 m wide and 5 m long and has a
constant spacing of 3 cm between the glass cover and the collector plate. Air
enters the collector at 30 °C at a rate of 0.15 m3/s through the 1-m-wide edge
and flows along the 5-m-long passage way. If the average temperatures of the
glass cover and the collector plate are 20 ° C and 60°C, respectively, determine
(a) the net rate of heat transfer to the air in the collector and (b) the
temperature rise of air as it flows through the collector.
Propiedades a 35 C ( T estimada):
8.43 Consider an air solar collector that is 1 m wide and 5 m long and has a
constant spacing of 3 cm between the glass cover and the collector plate. Air
enters the collector at 30 °C at a rate of 0.15 m3/s through the 1-m-wide edge
and flows along the 5-m-long passage way. If the average temperatures of the
glass cover and the collector plate are 20 ° C and 60°C, respectively, determine
(a) the net rate of heat transfer to the air in the collector and (b) the
temperature rise of air as it flows through the collector.
Propiedades a 35 C ( T estimada):
Propiedades a 35 C ( T estimada):
Reynolds:
Flujo turbulento
Flujo completamente
desarrollado
Propiedades a 35 C ( T estimada):
Nusselt y h:
Te y ΔT:
Propiedades a 35 C ( T estimada):
ΔTln y Q:
8. 48 A 15-cm x 20-cm printed circuit board whose components are not allowed
to come into direct contact with air for reliability reasons is to be cooled by
passing cool air through a 20-cm-long channel of rectangular cross section 0.2
cm x 14cm drilled into the board. The heat generated by the electronic
components is conducted across the thin layer of the board to the channel,
where it is removed by air that enters the channel at 15°C. The heat flux at the
top surface of the channel can be considered to be uniform, and heat transfer
through other surfaces is negligible. If the velocity of the air at the inlet of the
channel is not to exceed 4 m/s and the surface temperature of the channel is to
remain under 50°C, determine the maximum total power of the electronic
components that can safely be mounted on this circuit board.
Propiedades a 25 C ( T estimada):
Propiedades a 25 C ( T estimada):
Area transversal:
Reynolds:
Flujo laminar
Flujo en desarrollo
Propiedades a 25 C ( T estimada):
Nusselt h:
Propiedades a 25 C ( T estimada):
Q: