Introduction This document contains information about the setup steps required to
prepare for course CCP299.
Tip " See the Workstation Layout section of this General Setup document
for more information and workstation configuration details.
Job Aids The following job aids can be used to complete the exercises:
Logix5000 Systems Glossary
Studio 5000 Logix Designer and Logix5000 Procedures Guide
ControlLogix Troubleshooting Guide
Logix5000 Documentation Reference Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
CCP299_GeneralSetup
2 General Setup: Studio 5000 Logix Designer Level 1: ControlLogix Fundamentals and Troubleshooting
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
CCP299_GeneralSetup
General Setup: Studio 5000 Logix Designer Level 1: ControlLogix Fundamentals and Troubleshooting 3
Workstation Layout The ControlLogix workstation (or equivalent custom setup) used in
the course requires the following equipment:
12 dual input and output pushbuttons
4 selector switches (on/off)
2 analog inputs
2 analog meters
A 10-slot chassis with the modules listed in the following table:
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
CCP299_GeneralSetup
4 General Setup: Studio 5000 Logix Designer Level 1: ControlLogix Fundamentals and Troubleshooting
10-Slot ControlLogix
Chassis
12 Dual Discrete
Inputs/Outputs
Status Sta tus
J5 J5
DC Bus
J2
DC Bus Motion Equipment
(Not Required)
J2
L1 L1
100-240 100-240
L2/N VAC L2/N VAC
50/60 Hz 50/60 Hz
R R
J1 J1
S S
Motor
4 Selector
Motor
T T
Switches
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
CCP299_GeneralSetup
Exercise Setup: Locating ControlLogix System Components 5
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation or equivalent hardware
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aids The following job aid is recommended for use with this exercise:
Logix5000 System Glossary
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
CM3e56r_Setup
6 Exercise Setup: Locating ControlLogix System Components
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
CM3e56r_Setup
Exercise Setup: Navigating Through the Logix Designer Application 7
Required Hardware and The following hardware and software is required for this exercise:
Software Computer with the following software installed:
- Studio 5000
- RSLinx Classic
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Exercise Setup Before performing this exercise, return Logix Designer application
to default settings by performing the following actions:
1. If it is open, close the Logix Designer application.
2. Press and hold the CTRL + SHIFT key combination.
3. Continue holding the CTRL + SHIFT key combination and start
the software.
Recommended Job Aids The following job aids are recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Logix5000 System Glossary
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
NAVe56r_Setup
8 Exercise Setup: Navigating Through the Logix Designer Application
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
NAVe56r_Setup
Exercise Setup: Connecting a Computer to a Communications Network in a Logix5000 System 9
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
SAMTEC RSP-119350 USB cable (or equivalent)
EtherNet/IP network
Computer with the following software installed:
- RSLinx Classic Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP153.
Exercise Setup If any drivers are configured in RSLinx Classic software, stop them
and delete them before beginning this exercise.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
NE3e56r_setup
10 Exercise Setup: Connecting a Computer to a Communications Network in a Logix5000 System
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
NE3e56r_setup
Exercise Setup: Downloading and Going Online to a Logix5000 Controller 11
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
Networks and configured drivers:
- Serial (cable connected to the computer but not the controller)
- EtherNet/IP
Computer with the following software installed:
- Studio 5000
- RSLinx Classic Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Exercise Setup Serial and EtherNet/IP drivers must be configured for the network
using the default names.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
DG3e56r_setup
12 Exercise Setup: Downloading and Going Online to a Logix5000 Controller
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
DG3e56r_setup
Exercise Setup: Locating I/O Tags and Devices in a ControlLogix System 13
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Exercise Setup When preparing for this exercise, keep the following points in mind:
Be sure the following appendices are available from the exercise:
- I/O Wiring Diagrams
- I/O Wiring Diagrams for the HVAC System Application
An EtherNet/IP driver must be configured using RSLinx Classic
software.
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
IT3e56r_setup
14 Exercise Setup: Locating I/O Tags and Devices in a ControlLogix System
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
IT3e56r_setup
Exercise Setup: Interpreting Logix Designer Project Organization and Execution 15
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
TS3e56r_setup
16 Exercise Setup: Interpreting Logix Designer Project Organization and Execution
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
TS3e56r_setup
Exercise Setup: Interpreting Ladder Logic Structure in a Logix Designer Routine 17
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
ILLe56r_Setup
18 Exercise Setup: Interpreting Ladder Logic Structure in a Logix Designer Routine
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
ILLe56r_Setup
Exercise Setup: Locating and Editing Tag Values in a Logix Designer Project 19
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
TA3e56r_setup
20 Exercise Setup: Locating and Editing Tag Values in a Logix Designer Project
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
TA3e56r_setup
Exercise Setup: Interpreting Bit Instructions in a Logix Designer Routine 21
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aids The following job aid is recommended for use with this exercise:
Logix5000 Documentation Reference Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
IBIe56r_Setup
22 Exercise Setup: Interpreting Bit Instructions in a Logix Designer Routine
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
IBIe56r_Setup
Exercise Setup: Interpreting Frequently Used Instructions in a Logix Designer Routine 23
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation or equivalent hardware
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aids The following job aids are recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Logix5000 Documentation Reference Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
IC3e56r_setup
24 Exercise Setup: Interpreting Frequently Used Instructions in a Logix Designer Routine
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
IC3e56r_setup
Exercise Setup: Interpreting Arrays in a Logix Designer Project 25
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
AR3e56r_setup
26 Exercise Setup: Interpreting Arrays in a Logix Designer Project
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
AR3e56r_setup
Exercise Setup: Interpreting Tags of User-Defined Data Types in a Logix Designer Project 27
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
UD3e56r_setup
28 Exercise Setup: Interpreting Tags of User-Defined Data Types in a Logix Designer Project
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
UD3e56r_setup
Exercise Setup: Searching for Project Components in a Logix Designer Project 29
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
SL3e56r_setup
30 Exercise Setup: Searching for Project Components in a Logix Designer Project
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
SL3e56r_setup
Exercise Setup: Integrated Practice - Interpreting a Basic Logix Designer Project 31
Exercise Setup:
Integrated Practice - Interpreting a
Basic Logix Designer Project
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
IP3e56r_setup
32 Exercise Setup: Integrated Practice - Interpreting a Basic Logix Designer Project
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
IP3e56r_setup
Exercise Setup: Forcing I/O and Toggling Bits in the Logix Designer Application 33
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
FO3e56r_setup
34 Exercise Setup: Forcing I/O and Toggling Bits in the Logix Designer Application
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
FO3e56r_setup
Exercise Setup: Troubleshooting 1756 Digital I/O Module Problems 35
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
ControlLogix Troubleshooting Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
DI3e56r_setup
36 Exercise Setup: Troubleshooting 1756 Digital I/O Module Problems
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
DI3e56r_setup
Exercise Setup: Troubleshooting 1756 Analog I/O Module Problems 37
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
ControlLogix Troubleshooting Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
AN3e56r_setup
38 Exercise Setup: Troubleshooting 1756 Analog I/O Module Problems
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
AN3e56r_setup
Exercise Setup:Troubleshooting 1756 Remote I/O Problems 39
Exercise Setup:Troubleshooting
1756 Remote I/O Problems
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
ControlLogix Troubleshooting Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
CN3e56r_setup
40 Exercise Setup:Troubleshooting 1756 Remote I/O Problems
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
CN3e56r_setup
Exercise Setup: Updating Logix5000 Firmware 41
Required Hardware and The following hardware and software is required for this exercise:
Software Computer with the following software installed:
- Studio 5000
- RSLinx Classic
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aids The following job aids are recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
FW3e56r_Setup
42 Exercise Setup: Updating Logix5000 Firmware
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
FW3e56r_Setup
Exercise Setup: Troubleshooting ControlLogix Controller Problems 43
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
ControlLogix Troubleshooting Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
LE3e56r_setup
44 Exercise Setup: Troubleshooting ControlLogix Controller Problems
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
LE3e56r_setup
Exercise Setup: Troubleshooting ControlLogix Power Supply Problems 45
Required Hardware and The following hardware and software is required for this exercise:
Software Computer with the ability to run a flash animation execution file.
Recommended Job Aid The following job aid is recommended for use with this exercise:
ControlLogix Troubleshooting Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
PS3e56r_setup
46 Exercise Setup: Troubleshooting ControlLogix Power Supply Problems
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
PS3e56r_setup
Exercise Setup: Analyzing and Troubleshooting a System Using a Logix Designer Trend Chart 47
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
TR3e56r_setup
48 Exercise Setup: Analyzing and Troubleshooting a System Using a Logix Designer Trend Chart
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
TR3e56r_setup
Exercise Setup: Integrated Practice - Troubleshooting Basic Logix Designer Projects 49
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aids The following job aids are recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
ControlLogix Troubleshooting Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
LB3e56r_setup
50 Exercise Setup: Integrated Practice - Troubleshooting Basic Logix Designer Projects
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
LB3e56r_setup
Exercise Setup: Editing Ladder Logic Online in a Logix Designer Project 51
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
EN3e56r_setup
52 Exercise Setup: Editing Ladder Logic Online in a Logix Designer Project
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
EN3e56r_setup
Exercise Setup: Managing Logix Designer Project Files 53
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
FI3e56r_setup
54 Exercise Setup: Managing Logix Designer Project Files
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
FI3e56r_setup
Exercise Setup: Documenting and Printing Components in a Logix Designer Project 55
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation
EtherNet/IP network
Computer with the following software installed:
- Studio 5000
- RSLinx Classic OEM or Gateway with an activation file
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aid The following job aid is recommended for use with this exercise:
Studio 5000 Logix Designer and Logix5000 Procedures Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
DC3e56r_setup
56 Exercise Setup: Documenting and Printing Components in a Logix Designer Project
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
DC3e56r_setup
Exercise Setup: Troubleshooting Noise-Related Problems in a Logix5000 System 57
Recommended Job Aid The following job aid is recommended for use with this exercise:
ControlLogix Troubleshooting Guide
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
NO3e56r_setup
58 Exercise Setup: Troubleshooting Noise-Related Problems in a Logix5000 System
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
NO3e56r_setup
Exercise Setup: Understanding Control Systems 59
Required Hardware and The following hardware and software is required for this exercise:
Software ControlLogix workstation or equivalent hardware
Computer with the following software installed:
- Studio 5000
- RSLinx Classic
Tip " For more detailed hardware, software, and workstation information,
see the General Setup for CCP299.
Recommended Job Aids The following job aid is recommended for use with this exercise:
Logix5000 System Glossary
Rev. September 2013 E 2013 Rockwell Automation, Inc. All rights reserved.
UN3e56r_Setup
60 Exercise Setup: Understanding Control Systems
E 2013 Rockwell Automation, Inc. All rights reserved. Rev. September 2013
UN3e56r_Setup
Catalog Number ABT-CCP299-TIS - September 2013
Supersedes Catalog Number ABT- CCP299-TIS - January 2013
E 2013 Rockwell Automation, Inc. All rights reserved. Printed in USA