25 86%
1.What is the bad circuit of the system?
A. Intercom input power circuit.
4, When checking the bad circuit for this system at P-501of the CX-4723, pin B to pin A, with an
AN/PSM-45; your normal reading should be:
D. 22-30 volts DC.
5. When checking the bad circuit for this system you determine the CX-4723 is bad. You can prove the
CX-4723 is bad by performing what check?
D. Continuity check.
7. When checking the bad circuit for this symptom at P501 of the CX-4723, with an AN/PSM-45, and
your normal reading is correct; what is the bad item?
B. CX-4723.
8. When you have determined that the J-3513 is the bad item. You should take what corrective action to
fix the bad item?
A. Submit J-3513/U to COMSEC support maintenance.
9. What action should be taken after you have repaired this problem?
B. No action required.
13. When checking the bad circuit for this symptom at P-801 of CX-4723 with an AN/PSM-45; your
normal reading should be?
C. 22-30 volts DC.
16. What type of defect will cause NO SIDETONE in all of the control boxes?
D. A short.
1
17. When checking the bad circuit for this system, and you have determined there is sidetone heard at any
one of the other crewmember controls, C-2298; you can substitute that crewmembers C-2298 and CX-
4723 in place of the commander C-2298 and CX-4723, but there is still no sidetone. What would be the
bad item?
D. AM-1780.
18. What type of problem could affect the entire talk/listen circuit?
D. A short in the talk/listen circuit.
22. What must you do before measuring the circuit at P501 pin C to pin A?
D. Jumper pin B to pin C of J24.
23. When checking the bad circuit for this symptom, and checking at P501 pin C to pin A is normal; you
should take what action?
B. Disassemble the MT-1029, J-3513/U, and CX-4723, and measure continuity between pin C of J24
and pin C of J22 on the MT-1029.
27. When checking the bad circuit at J24, pin S to J5 pin B, with AN/PSM-45; what should the meter
reading indicate?
A. 24 VDC.
28. When checking the bad circuit at J24 pin S to J5 pin B with an AN/PSM-45, and the meter reading is
correct, what is the bad item?
A. RT-524.
2
33. What are the two parts of the bad circuit?
D. MT-1029, J-3513/U, CX-13061, CX-13062, KY-57.
34. Where should you check continuity on the MT-1029 to prove the mount is good or bad?
C. J24, pin H to J22 pin S.
35. Where should you check continuity on the CX-13062 to prove the cable is good or bad?
C. P1, pin C P2 pin C.
36. When checking the R-442 for no rushing noise heard in the earphone and speaker. According to EPC
step 24 and system diagram, what should be your first test?
B. Check continuity at the MT-1898, J14, pin E to L for continuity.
37. According to EPC step 30 and systems diagram where should you check the Am-1780 when there is no
loud rushing noise heard at CDR C-2298?
C. J-511, pin K to pin A circuit disturb the monitor circuit, listening to the handset.
38. According to EPC step 31 and systems diagram how can you prove the AM-1780 is good, when there is
no A-RT keying from the CDR box?
B. Measure continuity at J-501, pin S to J-504 pin D.
39. How can you determine the J-3513/U is good or bad when there is no modulation in EPC step 31?
A. Checking and eliminating the AM-1780 and CX-4723.
40. To determine the bad circuit, the headset is moved to the KY-57 audio jack. If alarm beeps are heard in
the handset, what is the bad circuit?
C. Squelch disable circuit.
41. What must be checked next if alarm beeps are not heard in the handset.
B. Voltage measurement at the KY-57 audio jack, pin A to C, (5.2VDC).
42. What are the possible bad items when the squelch disable circuit is determined to be bad?
B. A-RT, MT-1029, J-3513/U, CX-13061/U, KY-57.
43. What is the first test in checking the squelch disable circuit?
B. Check the CX-13061/U, jumper at P2 to pin G to pin N, then with another jumper wire, jumper
P2 pin T to shield, RT call lamp should light.
44. When doing the first test, the normal action does not occur, the next test is to measure continuity from
the MT-1029, J24 pin P to the CX-13061/U, P2, pin T. What is the bad item if zero ohms is measured?
A. A-RT.
45. It is determined the MT-1029, J-3513/U and CX-13061/U are still possibly bad. When checking
continuity on the MT-1029 and CX-13061/U zero ohms is measured on each circuit. What is the bad
item of equipment?
D. J-3513/U/U.
3
49. When checking the CX-13062 and infinity is measured, what is the bad item?
B. CX-13062/U
50. When checking the CX-13062/U and zero ohms is measured, what is the bad item?
A. J-3513/U.