SCHEDULE OF RATES
FOR
THANE & PALGHAR DISTRICT
2015-2016
SUPERINTENDING ENGINEER
THANE (PW) CIRCLE THANE
All rights reserved, No Part of this publication may
be reproduced, or transmitted, in any form or by
any means, without the prior permission in writing.
Schedule of Rates 2015-2016 - For Thane & Palghar District
INDEX
SR. PAGE NO.
CLASSIFICATION OF ITEMS
NO. FROM TO
1 GENERAL NOTES 1 7
2 BUILDING WORKS
2.1 Bd-A Excavation 8 9
2.2 Bd-B Pile Foundation 10 13
2.3 Bd-C Structural Steel Work 14 15
2.4 Bd-E Plain Cement Concrete 16 17
2.5 Bd-F Reinforced Cement Concrete 18 25
2.6 Bd-G Brick Masonry 26 28
2.7 Bd-H Stone Masonry 29 31
2.8 Bd-I Block Masonry 32 32
2.9 Bd-J Water Proofing 33 44
2.10 Bd-K Expansion Joints 45 47
2.11 Bd-L Plastering & Pointing 48 53
2.12 Bd-M Paving, Flooring & Dado 54 67
2.13 Bd-N Wood Finishes 68 69
2.14 Bd-O Oil Painting 70 73
2.15 Bd-P Colour / white washing & Distempering 74 74
2.16 Bd-Q Wood Work 75 77
2.17 Bd-R Roofing & Ceiling 78 88
2.18 Bd-T Doors & Windows 89 119
2.19 Bd-U Iron Works 120 120
2.20 Bd-V Water Supply & Sanitary Fittings 121 141
2.21 Bd-W Miscellaneous 142 156
3 ROAD WORK 157 181
4 BRIDGE WORK 182 224
5 CD WORK 225 228
6 BORING 229 232
7 SURVEY WORK
7.1 Departmental Agencies 233 237
7.2 Private Agencies 238 244
SR. PAGE NO.
CLASSIFICATION OF ITEMS
NO. FROM TO
8 VIDEOGRAPHY 245 246
9 Rates For Transportation 247 251
10 Material Rates 252 280
11 Labour Rates 281 282
12 Annexure A ( Pipe) 283 283
13 Annexure B (Office Material) 284 285
14 Annexure C (Laundry Rate) 286 286
15 Material consumption 287 305
16 Abbreviations 306 307
17 Vigilance DSR Rates 308 312
18 Frequency Chart of Vigilance & Quality Control 313 319
19 Letter for Approval 320 320
GENERAL NOTES
1 Schedule of Rates prepared for the year 2015-16 is Operative from
st
1 October 2015 and applicable for Thane & Palghar District.
2 For the rates in Corporation area, Notified Tribal area, Hilly inaccessible
areas, Central Jail premises & Mental Hospital premises an increase of
percentages over the normal schedule of rates (Basic completed item Rates)
Prescribed for the year 2015-16 are as follows.
1 Corporation Areas 5%
2 Notified Tribal Areas for building and minor and 10%
major bridge work only
3 Inside Premises of Jail, Mental Hospital 15%
premises ,
The increase in rates as above should be applicable only one at a time e.g. if Central
Jail is situated in Corporation area an increase of only 15% for the jail is to
be considered and not 20% (15% + 5%). Issue rates of Schedule ‘A’
materials for above notified area shall be increased by respective percentage.
The above percentage should be applied on the cost of items after deducting the cost
of Specified materials, if issued on Schedule 'A'.
Schedule of rates is based on the following basic rates of materials:
1
Rates for Bitumen
4.1 VAT, LBT & SALES TAX f o r m a t e r i a l s are not considered in the
rate abstract as market rate includes VAT, LBT. and SALES TAX, etc.
4.2 Turn over tax is not considered in the Rate Abstract .
4.3 i) As per Govt. circular No. DSR-1090 /CR-6453/PLN-3 dt. 14-7-1993, 1%
for labour amenity is considered in Rate Abstract.
ii) As per G.R. of Industries and power Department No.BCA-2009/CR-108/Labour 7-
A dated 17-06-2010, 1% cess for labour welfare is considered in the Rate
Abstract.
iii) As per revised circular issued by Dy. Directorate of Insurance Maharashtra
State v i d e letter No.|ÉÊ´ÉÊxÉ/2310/ºÉÉ.¤ÉÉÆ.Ê´É/ʴɨÉÉ ´ÉºÉÖ±ÉÒ/+ʦÉ-3 Eònù.8/9/2010 below mentioned
percentages for insurance of contract work shall be added in the Recapitulation
Sheet while Framing the estimate. The actual amount incurred by contractor for
insurance of work shall be reimbursed on production of documentary evidence
and after checking/ certification from Divisional Accounts Officer.
2
4.5 As Royalty charges for bricks, sand and crushed metal (as these are factory product)
are already paid by the quarry owner, same should not be considered in the rate
analysis.
4.6 The basic rates of materials are as per the Rates charged by the main producers
/ suppliers at their respective points of supply, as on the date of
implementation of D.S.R; which includes all taxes such as excise, CST, BST,
LBT, Terminal TAX, VAT, Educational Tax, Toll Tax, etc.
The rates of bulk/packed bitumen, bitumen emulsion adopted for the items
st
of bituminous works are based on the rates prevailing on 1 of June 2015 at
ex- Refinery Mumbai. The rates are inclusive of excise duty of 16% with
additional education cess of 3 % on excise duty and VAT 12.50%. Subsequent
increase/decrease, if any, in these rates shall be accounted for in the rate analysis of
the items while framing the estimate.
5.2 For calculation of pay load factor a truck of 10.00 M.T. Capacity is
considered.
5.3 The rates worked out in the Rate Abstract includes initial lead of 5 Km. for
all completed items, but excluding M.O.R.T. & H. Blacktopping items. For supply
items and providing Earth work in embankment of road materials
lead is not considered in the Rate Abstract. Actual lead charges are to be
added for these supply items while framing the estimate.
5.4 For working out Rates of items for additional leads more than 5 Kms. the
rate analysis should be prepared for actual leads by deducting initial lead
charges of 5 Kms for all completed items. For M.O.R.T. & H., items total lead
charges shall have to be considered in the Rate analysis.
5.5 For leads less than 1.00 Km. the rates worked out for head loads, should
be adopted as per statement C-2.
3
5.6 Lead charges for various materials are given in statement C -1 and these are
inclusive of loading and unloading charges. Hence loading and unloading charges
should not of loading and unloading charges. Hence loading and unloading charges
should not be added separately.
5.7 The Basic rates for all quarrying materials such as rubble , boulders,
aggregates, sand, murum, selected earth etc. are taken as rates at quarry
with lead of 50 mtr. (Head load lead which is not to be deducted from
lead)
5.8 For items of buildings having ground plus upper floors rate shall be increased
as follows for the floor lift.
Ground floor is the floor having height 3.80 m above average ground level.
The floor to floor height of 3.80 mtrs. is considered for the purpose of
lift charges. For floor to floor height more than 3.80 mtrs. the percentage
increase for the upper floor shall apply. The increase in rates as above
should be on ground floor basic rates only. No cumulative increase shall be
done.
Items to be carried out above terrace such as water proofing treatment on
terrace, water storage tank, parapet wall with coping, Stair -case, lift room with
slabs and water proofing treatment, plastering, painting etc. required for
the completion of building are assumed to be the items of its lower floor.
4
5.9 Additional lift for various, bridge items shall be as per list given below. Rate shall be
increased by percentage given below. Lift is to be measured with respect to common
datum level which will be specified in tender document/estimate.
b) For Piers, Abutment, Returns, wing walls, pier cap, slab, Box Returns, average
bed level shall be the datum.
6 General Guidelines
6.4 For cost towards procurement and temporary storage of water for construction
purpose necessary provisions are made in Rate abstract.
6.5 The rates for items pertaining to Parks & Gardens shall be taken from the DSR of
Director, Parks & Gardens.
6.6 The dewatering rates mentioned in bridge sections includes post monsoon
flow of River/ Nallas and general seepage of water only, and it include in
normal condition . In Specific conditions, if cofferdam, , caging etc. are felt essential
for dewatering then separate R.A. for that particular site may be prepared
and got approved from competent Authority.
6.7 For items of excavation, and masonry etc. for C.D. works, rates shall be
adopted from corresponding items under respective bridge sections.
5
6.8 For scaffolding work required to be erected for carrying out repairing work
on external faces of building at various heights (viz. repairs to chajja,
external plastering, painting etc.). The rate of respective item shall be
increased by1% provided the work is carried out by erecting scaffolding. For
specific cases rate analysis shall be got approved from concerned Superintending
Engineer
6.9 For quantity of concrete more than 50 Cu.M. mix design from approved laboratory
is necessary.
6.10 For excavation purpose, manual & mechanical means are proposed, when the
quantity of excavation is more than 100 Cu.M. Excavation by mechanical
means shall invariably be considered. In case the quantity is more than
100 Cu.Mt. and excavation by manual means is to be proposed,
Superintending Engineers prior approval will be necessary.
6.11 All concrete items considered in D.S.R. are inclusive of normal concrete curing
system. For building works costing more than Rs.125 lakhs, separate item for
intelligent concrete curing system shall be added in estimate.
6.13 No Concrete Mix from R.M.C. Plants shall be used for concrete works without
prior permission of Superintending Engineer.
6.14 Rates of the items using modern machineries with features are worked out including
cost of machineries and features therein.
7 Testing Of Material
7.1 Laboratory testing charges are not considered in the Rate Abstract. Wherever
required separate item shall be taken in the estimate for material testing
charges, on the basis of testing frequency and charges fixed by Vigilance
& Quality Control Circle, Pune for the current year and shall form part
of tender.
7.2 The job mix design for items like M-20 & above grade of concrete mix design, GSB,
asphaltic concrete, bituminous macadam etc. shall be obtained from the V.Q.C.C.
laboratory.
6
7.3 For Specific tests like span load tests, plate / pile load test etc. which are not included
in the rate analysis of item, the payment /estimates for these tests will be prepared on
the basis of rates approved by M.E.R.I.
8 This schedule of rates for Thane & Palghar district is prepared for the use of PWD.
However this may be used by other Govt. departments, PSUs, Private bodies &
individuals also at their own discretion. PWD shall not be responsible for any
ambiguity, discrepancy, dispute or financial loss, arising directly or indirectly by using
or following items of DSR by such Govt./ Private bodies or individuals.
9 Due care has been taken to print the PWD, DSR for Thane & Palghar districts, as
correctly as possible. It is however possible that some errors might have crept , in
case any error or omission is noticed, it may be brought to notice of the
Superintending Engineer, Thane P.W.Circle, Thane.
10 All rights reserved. No part of this publication may be reproduced in any form or by
any means, electronically or mechanically including photo copy, recording or in any
form, storage and retrieval system, without permission in writing from the
Superintending Engineer, P.W.Circle, Thane.
7
Bd-A Excavation
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
1 Excavation for foundation in ------------- including
removing the excavated material up to a distance of
50 m. beyond the building area & stacking and
spreading as directed, dewatering, preparing the bed
for the foundation and necessary back filling,
ramming, watering including shoring and strutting etc.
complete. (Lift upto 1.5 m.)
Spec. No.: Bd.A.1-6 Page No. 13
A By Manual Means
i earth, soil of all types, sand, gravel and soft murum Cu.Mt. 138.00 135.00
ii Hard Murum Cu.Mt. 149.00 146.00
iii Hard Murum and boulders Cu.Mt. 178.00 173.00
iv Soft rock Cu.Mt. 430.00 369.00
v In hard rock (blasting) Cu.Mt. 654.00 444.00
vi In hard rock (By controlled blasting) Cu.Mt. 785.00 527.00
vii Hard rock chiselled and wedged or line drilled Cu.Mt. 899.00 873.00
viii Laterite rock Cu.Mt. 545.00 429.00
B By Mechanical Means
i earth, soil of all types, sand, gravel and soft murum Cu.Mt. 104.00 46.00
8
Bd-A Excavation
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
iii Hard Murum and boulders Cu.Mt. 183.00 179.00
iv Soft rock Cu.Mt. 406.00 346.00
v In hard rock (blasting) Cu.Mt. 725.00 468.00
B By Mechanical Means
i earth, soil of all types, sand, gravel and soft murum Cu.Mt. 117.00 63.00
ii Hard Murum Cu.Mt. 131.00 71.00
iii Hard Murum and boulders Cu.Mt. 143.00 74.00
iv Soft rock Cu.Mt. 280.00 219.00
3 Filling in plinth and floors with approved excavated Cu.Mt. 58.00 56.00
materials in 15 cm to 20 cm layers including watering
and compaction complete.
Spec. No.: Bd.A.10 Page No. 18
4 Filling in plinth and floors with contractors soil sand Cu.Mt. 505.00 89.00
or murum in 15 cm to 20cm, layers including watering
and compaction complete.
Spec. No.: Bd.A.11 Page No. 18
5 Providing dry/ trap/ granite/ quartzite/ gneiss rubble Cu.Mt. 950.00 214.00
stone soiling 15 cm to 20 cm thick including hand
packing and compacting complete.
Spec. No.: Bd.A. 12 Page No. 19
6 Providing and filling in the foundation with sand of ap- Cu.Mt. 1254.00 53.00
proved quality including watering, compaction
complete.
Spec. No.: Bd.A.13 Page No. 20
7 Providing soling using 80 mm size trap metal in 15 Cu.Mt. 1057.00 295.00
cm. layer including filling voids with Crushed sand/grit
ramming, watering complete.
Spec. No.: As directed by Engineer in charge.
9
Bd-B Pile Foundation
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
1 Providing ......... RCC cast in situ bored piles of -
-------- mm dia. each of load capacity as per
design and of specified diameter or as directed,
placed through steel sheel sunk to the required
depth through all strata except rock, excluding
provision of reinforcement, including placing
concrete by tremie arrangement, compaction of
concrete and withdrawal of steel shell etc.
complete.
Spec. No.: Bd-B-2 Page 30
A) M-25
i) 325 mm diameter R.Mt. 1122.00 393.00
ii) 350 mm diameter R.Mt. 1151.00 403.00
iii) 400 mm diameter R.Mt. 1348.00 472.00
iv) 450 mm diameter R.Mt. 1443.00 505.00
v) 500 mm diameter R.Mt. 1758.00 563.00
vi) 550 mm diameter R.Mt. 1989.00 636.00
vii) 600 mm diameter R.Mt. 2223.00 711.00
B) M-30
i) 325 mm diameter R.Mt. 1142.00 393.00
ii) 350 mm diameter R.Mt. 1213.00 403.00
iii) 400 mm diameter R.Mt. 1396.00 472.00
iv) 450 mm diameter R.Mt. 1495.00 505.00
v) 500 mm diameter R.Mt. 1812.00 563.00
vi) 550 mm diameter R.Mt. 2067.00 636.00
vii) 600 mm diameter R.Mt. 2315.00 711.00
C) M-35
i) 325 mm diameter R.Mt. 1153.00 393.00
ii) 350 mm diameter R.Mt. 1244.00 403.00
iii) 400 mm diameter R.Mt. 1420.00 472.00
iv) 450 mm diameter R.Mt. 1521.00 505.00
v) 500 mm diameter R.Mt. 1828.00 563.00
vi) 550 mm diameter R.Mt. 2106.00 636.00
vii) 600 mm diameter R.Mt. 2361.00 711.00
10
Bd-B Pile Foundation
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
2 Providing RCC cast insitu ........ rim bored piles
of --------- grade concrete of .......mm dia. each of
load capacity as per design and of specified
diameter of pile and bulb as directed, sunk to the
required depth through all strata except
rock,excluding provision of reinforcement including
placing reversible drum type concrete mixer
concrete by tremie arrangement compaction of
concrete etc. complete.
Spec. No.: Bd-B-2 Page 27 & 33
A) Single Rim
a) M-25
i 225 mm R.Mt. 679.00 238.00
ii 300 mm R.Mt. 887.00 310.00
iii 380 mm R.Mt. 1278.00 435.00
iv 450 mm R.Mt. 1516.00 500.00
v 535 mm R.Mt. 1985.00 635.00
vi 600 mm R.Mt. 2518.00 781.00
b) M-30
i 225 mm R.Mt. 687.00 238.00
ii 300 mm R.Mt. 901.00 310.00
iii 380 mm R.Mt. 1301.00 435.00
iv 450 mm R.Mt. 1548.00 500.00
v 535 mm R.Mt. 2031.00 635.00
vi 600 mm R.Mt. 2576.00 781.00
c) M-35
i 225 mm R.Mt. 691.00 238.00
ii 300 mm R.Mt. 909.00 310.00
iii 380 mm R.Mt. 1313.00 435.00
iv 450 mm R.Mt. 1565.00 500.00
v 535 mm R.Mt. 2055.00 635.00
vi 600 mm R.Mt. 2606.00 781.00
11
Bd-B Pile Foundation
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
B) Double Rim
a) M-25
i 225 mm R.Mt. 707.00 247.00
ii 300 mm R.Mt. 929.00 320.00
iii 380 mm R.Mt. 1421.00 469.00
iv 450 mm R.Mt. 2015.00 645.00
v 535 mm R.Mt. 2976.00 878.00
vi 600 mm R.Mt. 3911.00 1115.00
b) M-30
i 225 mm R.Mt. 716.00 247.00
ii 300 mm R.Mt. 944.00 320.00
iii 380 mm R.Mt. 1445.00 469.00
iv 450 mm R.Mt. 2049.00 645.00
v 535 mm R.Mt. 3025.00 878.00
vi 600 mm R.Mt. 3972.00 1115.00
c) M-35
i 225 mm R.Mt. 722.00 247.00
ii 300 mm R.Mt. 954.00 320.00
iii 380 mm R.Mt. 1460.00 469.00
iv 450 mm R.Mt. 2069.00 645.00
v 535 mm R.Mt. 3053.00 878.00
vi 600 mm R.Mt. 4005.00 1115.00
3 Chipping and dressing of the R.C.C. piles upto No. 240.00 233.00
0.60m. including cleaning reinforcement and
removal of dismantled materials for providing
pile caps etc. complete.
Spec. No.: As directed by Engineer-in-charge
4 Providing bentonite slurry process for up to 650 R.Mt. 135.00 19.00
mm.dia. diameter of piles etc. complete.
Spec. No.: As directed by Engineer-in-charge
12
Bd-B Pile Foundation
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
5 Chiselling through pile shells in hard strata like
boulders, soft and hard rocks including removing
and stacking the loose materials etc. complete
and disposing of the unserviceable materials
outside etc. complete.
Spec. No.: As directed by Engineer in charge.
a) upto and inclusive of 550 mm diameter. Rig Hour 416.00 416.00
b) Beyond 550 mm and upto and inclusive of 650 Rig Hour 555.00 555.00
mm dia.
6 Carrying out load test for 1.5 times the proposed
safe working load on the pile in driven position ------
-------- diameter. including construction of test cap,
use of accessories and in strum including
providing graphs as per I.S. code standards and
dismiss the cap etc. and clearing site etc.
completed.
Spec. No.: As directed by Engineer in charge.
i Up to 400 mm diameter No. 40800.00 0.00
ii 400 mm Up to 550 mm diameter No. 49300.00 0.00
iii 550 mm Up to 650 mm diameter No. 59700.00 0.00
7 Empty boring for ………………. dia bored R.C.C.
cast in situ piles including withdrawel of shell,
removal of earth to distance of 50 meters etc.
complete.
Spec. No.: As directed by Engineer in charge.
i 325 to 400 mm diameter R.Mt. 380.00
ii 425 mm Up to 500 mm diameter R.Mt. 425.00
iii 525 mm Up to 600 mm diameter R.Mt. 440.00
13
Bd-C Structural Steel Work
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
1 Providing and fabricating structural steel work in M.T. 67718.00 9410.00
rolled sections like joists, channels, angles, tees
etc. as per detailed designs and drawing or as
directed by Engineer-in-charge including cutting,
fabrication, hoisting & erecting fixing in position with
connecting plates, braces etc. and one coat of
anticorrosive paint and over it two coat of oil
paintings of approved quality and shade complete.
Spec. No.: Bd.C.2 Page No. 49
14
Bd-C Structural Steel Work
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
4 Providing structural steel work in trusses, other M.T. 75856.00 19538.00
similar trussed purlins and members with all
bracing, gusset plates etc. as per detailed designs
and drawings or as directed including cutting,
fabricating, hoisting, erecting fixing in position,
Making riveted/ bolted/ welded connection and one
coat of anticorrosive paint and over it 2 coats of oil
painting complete,
Spec. No.: Bd.C.8 Page No. 54
5 Providing and fixing 50 mm. dia. medium class Sq.Mt. 3702.00 1689.00
G.I.pipe gate with wicket gate of approved drawing
with all fixtures & fittings in two leaves with strong
hold fast embedded in c.c. block at top & bottom
with locking arrangement including cutting, bending,
making holes and with one coat of primer complete.
Spec. No.: As directed by Engineer in charge.
6 Providing, hoisting and fixing in position mild steel M.T. 69596.00 2168.00
Tubular Trusses of required span as per drawing
and design including purlins, wind bracing, runners,
gusset plates foundations bolts including painting 3
coats of oil paint approved quality and shade,
scaffolding etc. complete as per ISI specifications.
Spec. No.: B-18 Page No. 57
15
Bd - E : Plain Cement Concrete
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing and casting in situ cement concrete 1:2:4
of trap / granite / quartzite / gneiss metal for
foundation & bedding including centering,
formwork, compacting, roughening them if special
finish is to be provided and curing and finishing if
required complete,with..............
Spec. No.: Bd.E.2 Page No. 288 and B.7 Page No
70
A without Formwork
i With SCADA with fully automatic micro processor Cu.Mt. 5025.00 827.00
based PLC with SCADA enabled reversible Drum
Type mixer
ii Without SCADA with concrete mixer with hopper Cu.Mt. 5021.00 865.00
B with Formwork
i With SCADA with fully automatic micro processor Cu.Mt. 5170.00 830.00
based PLC with SCADA enabled reversible Drum
Type mixer
ii Without SCADA with concrete mixer with hopper Cu.Mt. 5165.00 866.00
16
Bd - E : Plain Cement Concrete
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
3 Providing and casting in situ cement concrete of
........... grade of trap / granite /quartzite/ gneiss
metal for bed blocks, foundation blocks and
such other items including bailing out water
formwork, compacting, roughening, them if special
finish is to be provided and curing and finishing if
required complete, with.............
Spec. No.: Bd.E.4 Page No. 72 and B-7, Page
No.38
5 Providing and casting in situ cement concrete M-20 Cu.Mt. 5390.00 846.00
of trap metal for coping to plinth or parapet,
moulded or chamfered as per drawings or As
directed by Engineer-In-Charge., including
formwork roughening the exposed faces if special
finish is to be provided and curing etc. complete.
Without SCADA
Spec. No.: BdE-3 Page No. 71
17
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
1 Providing and laying in situ cement concrete of
specified grade of trap / granite /quartzite/ gneiss
metal for R.C.C. work in .......................... like raft,
strip foundations, grillage and footings of R.C.C.
columns and steel stanchions etc. including bailing
out water, formwork, cover blocks compaction and
curing etc. (Excluding reinforcement and structural
steel) complete, With...........of grade ........
Spec. No.: Bd.F.3 Page No. 89 Page No.38
18
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
a M-20 Cu.Mt. 7370.00 1463.00
b M-25 Cu.Mt. 7560.00 1465.00
c M-30 Cu.Mt. 7752.00 1467.00
3 Providing & casting in situ cement concrete of
specified grade of trap / granite /quartzite/ gneiss
metal for R.C.C. beams and lintels as per detailed
designs & drawings or as directed including
plywood/steel centering, formwork, cover blocks
compaction & roughening the surface if special finish
is to be provided & curing complete. (Excluding
reinforcement). With.........
Spec. No.: Bd.F.6 Page No. 91, Page No.38
A With SCADA with fully automatic micro processor
based PLC with SCADA enabled reversible Drum
Type mixer
a M-20 Cu.Mt. 7542.00 1672.00
b M-25 Cu.Mt. 7734.00 1679.00
c M-30 Cu.Mt. 7925.00 1685.00
B Without SCADA with concrete mixer with hopper
a M-20 Cu.Mt. 7537.00 1716.00
b M-25 Cu.Mt. 7729.00 1721.00
c M-30 Cu.Mt. 7920.00 1727.00
4 Providing and casting in situ cement concrete-
specified of trap/ granite / quartzite/ gneiss metal for
R.C.C. slabs and landings canopy as per detailed
designs and drawings including plywood/steel
centering, formwork, cover blocks compacting and
roughening the surface if special finish is to be
provided and curing complete. (Excluding
reinforcement).With.........
Spec. No.: Bd.F.8 Page No. 93
A With SCADA with fully automatic micro processor
based PLC with SCADA enabled reversible Drum
Type mixer
a M-20 Cu.Mt. 7880.00 1858.00
b M-25 Cu.Mt. 8072.00 1865.00
c M-30 Cu.Mt. 8264.00 1872.00
19
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
B Without SCADA with concrete mixer with hopper
a M-20 Cu.Mt. 7875.00 1904.00
b M-25 Cu.Mt. 8067.00 1910.00
c M-30 Cu.Mt. 8259.00 1917.00
5 Providing & casting in situ cement concrete
of.. specified grade of trap/ granite/ quartzite/ gneiss
metal for R.C.C. chajja as per detailed design &
drawings including centering, formwork, cover blocks
compacting & roughening the surface if special finish
is to be provided & curing complete. (Excluding
reinforcement).With .........
Spec. No.: Bd.F.9 Page No. 95
A With SCADA with fully automatic micro processor
based PLC with SCADA enabled reversible Drum
Type mixer
a M-20 Cu.Mt. 8702.00 1848.00
b M-25 Cu.Mt. 8894.00 1855.00
c M-30 Cu.Mt. 9086.00 1860.00
B Without SCADA with concrete mixer with hopper
a M-20 Cu.Mt. 8697.00 1889.00
b M-25 Cu.Mt. 8889.00 1895.00
c M-30 Cu.Mt. 9081.00 1901.00
6 Providing and casting in situ cement concrete
of. specified. grade of trap/ granite/ quartzite/ gneiss
metal for R.C.C. pardi 75mm thick fins including
centering, formwork, cover blocks compacting and
roughening them if special finish is to be provided and
curing complete. (Excluding reinforcement).with .........
Spec. No.: Bd.F.11 Page No. 96
20
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
B Without SCADA with concrete mixer with hopper
a M-20 Cu.Mt. 9150.00 2245.00
b M-25 Cu.Mt. 9342.00 2213.00
c M-30 Cu.Mt. 9534.00 2260.00
7 Providing and casting in situ cement concrete
of. specified grade of trap/ granite/ quartzite/ gneiss
metal for R.C.C.coping to plinth or parapet amd sill
of doors and windows moulded as per detailed
drawings or chamfered as approved by the Engineer
including centering, formwork, cover blocks
compacting and roughening them if special finish is to
be provided and curing complete. (Excluding
reinforcement).With.........
Spec. No.: Bd. F. 12 Page No. 96 & B-7, Pg 38
A With SCADA with fully automatic micro processor
based PLC with SCADA enabled reversible Drum
Type mixer
a M-20 Cu.Mt. 5893.00 1028.00
b M-25 Cu.Mt. 6085.00 1032.00
c M-30 Cu.Mt. 6277.00 1035.00
B Without SCADA with concrete mixer with hopper
a M-20 Cu.Mt. 5888.00 1065.00
b M-25 Cu.Mt. 6080.00 1067.00
c M-30 Cu.Mt. 6272.00 1070.00
8 Providing and casting in situ cement concrete
of. specified grade of trap/ granite/ quartzite/ gneiss
metal for R.C.C.waist slab steps & parapets to plinth
or parapet amd sill of doors and windows moulded as
per detailed drawings or chamfered as approved by
the Engineer including centering, formwork, cover
blocks compacting and roughening them if special
finish is to be provided and curing complete.
(Excluding reinforcement).with.........
Spec. No.: Bd. F. 13 Page No. 97 & B-7, Pg 38
21
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
A With SCADA with fully automatic micro processor
based PLC with SCADA enabled reversible Drum
Type mixer
a M-20 Cu.Mt. 8284.00 1918.00
b M-25 Cu.Mt. 8476.00 1925.00
c M-30 Cu.Mt. 8668.00 1932.00
B Without SCADA with concrete mixer with hopper
a M-20 Cu.Mt. 8279.00 1962.00
b M-25 Cu.Mt. 8471.00 1973.00
c M-30 Cu.Mt. 8663.00 1976.00
9 Providing and fixing in position after hoisting, precast Sq.Mt. 674.00 74.00
1:2 cement mortar reinforcement Jali 50mm thick of
approved design cement mortar 1:3 and curing
complete (including 6mm diameter mild steel bar
reinforcement).
Spec. No.: Bd. F. 20 Page No. 100
10 Providing and fixing in position............ bar
reinforcement of of TATA TISCON /SAILl /JSW
/ESSAR or equivalent make (condirming to IS code)
of various diameters for R.C.C. pile caps, footings,
foundations, slabs, beams columns, canopies,
staircase, newels, chajjas, lintels pardis, copings, fins,
arches etc. as per detailed designs, drawings and
schedules. including cutting, bending, hooking the
bars, binding with wires or tack welding and
supporting as required including cover block etc.
complete.
Spec. No.: Bd.F.17, Page No. 98
a TMT- Fe-500/Fe-415 M.T. 70159.00 6802.00
b Mild Steel M.T. 54784.00 5400.00
22
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
11 Providing and casting in situ c.c. specified garde of
trap metal for RCC Pile caps as per detailed design
and drawing or as directed including dewatering if
necessary, centering, formwork, cover blocks
compacting, finishing the form surface with C.M. 1:3 of
sufficient minimum thickness to give smooth and even
surface or roughening them if special finish is to be
provided and curing complete (Excluding
reinforcement). With.............
Spec. No.: Bd. F1. Page No. 98
A With SCADA with fully automatic micro processor
based PLC with SCADA enabled reversible Drum
Type mixer
a M-20 Cu.Mt. 5877.00 1047.00
b M-25 Cu.Mt. 6069.00 1050.00
c M-30 Cu.Mt. 6259.00 1050.00
B Without SCADA with concrete mixer with hopper
a M-20 Cu.Mt. 5872.00 1088.00
b M-25 Cu.Mt. 6064.00 1090.00
c M-30 Cu.Mt. 6254.00 1090.00
12 Providing and fixing fan hook box of 2 mm thick M.S. No. 236.00 19.00
sheet rectangular size 180x100 mm with required
depth with holes or notches as required, bottom and
top sides of 1.6 mm M.S. sheet fixed with 3.5 mm dia.
round headed screws together with 12 mm dia. M.S.
bar bent to shape with hooked ends for fan hook and
painting to exposed surface as directed.
Spec. No.: As directed by Engineer in charge
23
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
13 Providing and laying in position Ready mix
concrete for rainforced cement concrete with crushed
sand, for in ............. work, of .........grade cement
content as per approved design mix, and
manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads,
having continuous agitated mixer, manufactured as
per mix design of specifiied grade for reinforced
cement concrete work including pumping of R.M.C.
from transit mixer to site of laying, including the cost of
plywood/steel centering, shuttering , compacting and
curing including cost of admixtures in recommendeed
proportion aas per IS : 9103 to accelerate /retard
setting of concrete, improve workability without
impairintg strength and durability as per direction of
the Engineer - in - charge. (With SCADA with fully
automatic micro processor based PLC with SCADA
enabled reversible Drum Type mixer ) (Prior
permission of S.E.is essential)
Spec. No. Bd. F 3 page No.89
24
Bd - F : Reinforced Cement Concrete
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
iii M-30 Cu.Mt. 7576.00 813.00
D For Slabs & Landings
Spec. No.: Bd.F.8 Page No. 93
i M-20 Cu.Mt. 7540.00 839.00
ii M-25 Cu.Mt. 7727.00 828.00
iii M-30 Cu.Mt. 7914.00 830.00
E For Waist Slabs , steps and parapit
Spec. No.: Bd.F.13 Page No.97
i M-20 Cu.Mt. 7944.00 826.00
ii M-25 Cu.Mt. 8131.00 828.00
iii M-30 Cu.Mt. 8318.00 830.00
F For Pile Caps
Spec. No.: Bd.F.6 Page No.87
i M-20 Cu.Mt. 5453.00 650.00
ii M-25 Cu.Mt. 5640.00 650.00
iii M-30 Cu.Mt. 5826.00 650.00
25
Bd - G : Brick Masonary
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing second class Burnt Brick masonry with Cu.Mt. 4917.00 827.00
conventional/ I.S. type bricks in cement mortar 1:6 in
foundations and plinth of inner walls/ in plinth
external walls including bailing out water, striking
joints on unexposed faces, raking out joints on
exposed faces and watering Complete.
Spec. No.: Bd.G. 1 Page No. 265
2 Providing first class Burnt Brick masonry with Cu.Mt. 5103.00 951.00
conventional/ I.S. type bricks in cement mortar 1:6
in plinth including bailing out water, striking joints
on unexposed faces, pointing with cement mortar
1:3 on exposed face and watering Complete.
Spec. No.: Bd.G.2 Page No. 265
3 Providing second class Burnt Brick masonry with Cu.Mt. 4804.00 707.00
conventional/ I.S. type bricks in cement mortar 1:6 in
plinth as backing in composite masonry including
bailing out water, striking joints, racking out joints
and watering Complete.
Spec. No.: Bd.G.3 Page No. 265
4 Providing second class Burnt Brick masonry with Cu.Mt. 4984.00 856.00
conventional/ I.S. type bricks in cement mortar 1:6 in
superstructure including striking joints, racking out
joints, watering and scaffolding Complete.
Spec. No.: Bd.G.5 Page No. 268
5 Providing second class Burnt Brick masonry with Sq.Mt. 675.00 99.00
conventional/ I.S. type bricks in cement mortar 1:4 in
half brick thick wall including mild steel
longitudinal reinforcement of 2 bars of 6 mm
diameter / 2 hoop iron strips 25 mm X 1.6 mm at
every third course, properly bent and bonded at
ends scaffolding, racking out joints and watering
Complete.
Spec. No.: Bd.G.7 Page No. 269
26
Bd - G : Brick Masonary
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
6 Providing Burnt Brick-on-edge in half brick thick Sq.Mt. 546.00 98.00
wall masonry with second class bricks of
conventional type bricks in cement mortar 1:3
including mild steel longitudinal reinforcement of 2
bars of 6mm diameter / one strips of hoop iron 25
mm X 1.6 mm placed at every third course, properly
bent and bonded at ends, scaffolding, raking out
joints and watering complete.
Spec. No.: Bd.G.8 Page No. 270
7 Providing first class Burnt Brick masonry with Cu.Mt. 5357.00 1254.00
conventional / I.S. type bricks in cement mortar 1:4
including scaffolding, racking joints pointing in C.M.
1:3 and watering in pillars of rectangular or
square shape as shown on the drawing or as
directed complete.
Spec. No.: Bd.G.9 (a) Page No. 270
8 Providing first class Brick masonry with conventional Cu.Mt. 5443.00 1175.00
/ IS. type bricks in cement mortar 1:4 including
scaffolding, racking out joints pointing in C.M 1:3
and watering in pillars of curved shapes, as
shown on the drawing or as directed complete.
Spec. No.: Bd.G.9 (b) Page No. 270
9 Providing second class Burnt Brick masonry with Cu.Mt. 5086.00 935.00
conventional / I.S. type bricks in cement mortar 1:4
including scaffolding racking joints and watering in
pillar of rectangular shapes as shown in the
drawings or as directed complete.
Spec. No.: Bd.G.10 (a) Page No. 271
10 Providing second class Burnt Brick masonry with Cu.Mt. 5115.00 872.00
conventional / I.S. type bricks in cement mortar 1:4
including scaffolding, racking out joints and watering
in pillar of curved shapes as shown in the drawing
or as directed complete.
Spec. No.: Bd.G.10 (b) Page No. 271
27
Bd - G : Brick Masonary
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
11 Providing fly ash brick masonry with conventional / Cu.Mt. 5130.00 1693.00
I.S. type fly ash brick in cement mortar 1:6 including
striking joints, racking out joints watering and
scaffolding complete. For foundation & plinth
BDG- 1&2 page 265 and
28
Bd - H : Stone Masonary
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing uncoursed rubble masonry of trap / Cu.Mt. 2930.00 1041.00
granite / quartzite / gneiss stones in cement
mortar 1:6 in foundation and plinth of inner
walls / in plinth of external walls including bailing
out water, striking joints on un exposed faces and
watering complete.
Spec. No.: Bd.H.1 Page No. 293
2 Providing uncoursed rubble masonry of trap / Cu.Mt. 3091.00 1168.00
granite / quartzite / gneiss stones in cement
mortar 1:5 in basements including scaffolding,
bailing out water, racking out joints when
plastering is to be done striking joints where no
pointing or plastering is to be done and watering
complete.
Spec. No.: Bd.H.2 Page No. 293
3 Providing uncoursed rubble masonry of trap / Cu.Mt. 3576.00 987.00
granite / quartzite / gneiss stone in cement mortar
1:3 in basement with patent water proofing
compound added to it at rate of 1 kg per bag of
cement including bailing out water, scaffolding
racking out joints when plastering is to be done
and watering complete.
Spec. No.: Bd.H.3 Page No. 294
4 Providing uncoursed rubble masonry of trap / Cu.Mt. 3260.00 911.00
granite / quartzite / gneiss stones in cement
mortar 1:6 in superstructure including racking
out joints when plastering is to be done / striking
joints when no plastering is to be done watering
and scaffolding complete.
Spec. No.: Bd.H.4 Page No. 296
5 Providing random rubble masonry second sort of Cu.Mt. 3012.00 1089.00
trap / granite / quartzite / gneiss stones in cement
mortar 1:6 in plinth including bailing out water ,
striking joints on unexposed faces. (Excluding
pointing) complete.
Spec. No.: Bd.H.5 Page No. 296
29
Bd - H : Stone Masonary
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
6 Providing random rubble masonry second sort of Cu.Mt. 3225.00 1228.00
trap / granite / quartzite / gneiss stones in cement
mortar 1:6 in superstructure racking out joints
when plastering is to be done / striking joints
when no pointing or plastering is to be done on
the inside watering and scaffolding complete.
Spec. No.: Bd.H.6 Page No. 296
30
Bd - H : Stone Masonary
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
11 Providing coursed rubble masonry first sort of trap Cu.Mt. 6381.00 1633.00
/ granite / quartzite / gneiss stones in cement
mortar 1:6 in external work of plinth including
bailing out water, striking joints inside and
watering complete.
Spec. No.: Bd.H.13 Page No. 299
12 Providing coursed rubble masonry first sort of Cu.Mt. 6852.00 1752.00
trap / granite / quartzite / gneiss stones in cement
mortar 1:6 in superstructure including racking
out joints on the inside when plastering is to be
done, watering and scaffolding complete.
Spec. No.: Bd.H.14 Page No. 299
13 Providing coursed rubble masonry first sort for Cu.Mt. 6955.00 2282.00
pillars of trap / granite / quartzite / gneiss stones
in cement mortar 1:6 including pointing with
cement mortar 1:3 scaffolding and watering
complete.
Spec. No.: Bd.H.40 Page No. 299
31
Bd - I : Block Masonary
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
Providing and laying masonry of I.S. Sq.Mt. 508.00 168.00
Standard C.C. hollow block 400 x 200 x 100
mm in cement mortar 1:6 proportion for
1 superstructure including curing, scaffolding
etc. complete.
Spec. No.: Bd.I.1 Page No. 349
32
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
1 Providing and laying damp proof course 50mm Sq.Mt. 274.00 44.00
thick in (1:2:4) cement concrete layer and bitumen
/ using cement with waterproofing compound
curing, formwork etc. complete.
Spec. No.: Bd.J.2 Page No. 337
2 Providing and applying Bitumen layer at 2 kg. per Sq.Mt. 149.00 9.00
square meter over the terrace, structural slab
including cleaning the surface for waterproofing as
directed complete
Spec. No.: Bd.J.3 Page No. 338
33
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
cement bag including all lead, lifts & laid to proper
slope to drain off water entirely including watta at
the junction of parapet and work up to a height of
30 cm. or as directed and including finishing the
top layer of water proofing treatment with false
marking of 30 x30 cm. or as directed and covering
the whole treatment with 7 years guarantee on
requisite stamp paper etc. complete.
Spec. No.: As directed by Engineer in charge.
6 Removing the tar or coba and disposing of the Sq.Mt. 11.00 11.00
material as directed etc. complete.
Spec. No.: As directed by Engineer in charge.
34
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
on perfectly clean surface (free from loose dust
and foreign matter) application of 1st coat of
Polydee-LM @ 700 gms/sqm and applying 2nd
coat of Polydee-LM @ 700 gms/sqm and finishing
the same with sprinkling the AG-10 granules on
the wet coating. (After finishing covering the
treatment with 25mm cement plaster for protection
with fibrillated 6mm Plyplast fibre @ 125 gms/sqm
to be paid in separate item.) covering 7 years
guarantee on Court Fee Stamp Paper of Rs. 100/-
etc. complete.
Spec. No.: As directed by Engineer in charge
35
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
10 with 7 years guarantee on court fee stamp of
Rs.100/- with ponding test etc complete.
(excluding Cement concrete 1:3:6 base concrete )
( prior permission of SE shall be obtained before
inclusion of item )
Spec. No.: Bd.J.2 Page No. 337
36
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
13 Providing and applying required coats of a water Sq.Mt. 294.00 55.00
based UV resistant Evercrete Top Seal sealant to
protect natural stone, bricks, concrete and wooden
structures from water intrusion and staining due to
water penetration and algae formation etc
complete.
Spec. No.: As directed by Engineer in charge.
14 Providing and applying required coats of a water Sq.Mt. 483.00 63.00
based Evercrete Deep Penetrating Sealer (DPS)
on cement concrete surface like roads, beams,
and columns, plastered walls, basements, roofs,
potable water tanks etc to react
15 Finishing the terrace slab integrally mixed with Sq.Mt. 238.00 100.00
water proofing compound in cement mortar 1:3
proporation with 20 mm thick layer, including
curing, finishing using approved water proofing
compound at rate of 1 kg per 50 kg of cement etc.
complete.
Spec. No.: As directed by Engineer-in-charge
16 Providing waterproof plaster in W.C. and bath 20 Sq.Mt. 240.00 149.00
mm thick for dado in cement mortar 1:3 with neat
finishing, floating using approved waterproofing
compound of IS Std. at the rate of one kg per 50
kg of cement.
Spec. No.: As directed by Engineer-in-charge
37
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
17 Providing waterproofing in W.C. and bath Cu.Mt. 2790.00 72.00
including brick bat coba in all positions consisting
of specialised materials as per IS Standard and
covering 7 years guarantee including all leads, lifts
etc. complete.
Spec. No.: As directed by Engineer-in-charge
18 For RCC Slab : Mechanically clean the RCC slab Sq.Mt. 549.00 0.00
and wall with wire brush / coir brush to free from
all loose materials like dust, dirt etc. Make wattah /
coving of 50x50 mm at all horizontal & vertical
joints to avoid right angle
horizontal & vertical joints to avoid right angle
turning.Seal all honeycombs, pin holes, joints,
pipe outlets with Polymer Modified Mortar . Also,
pouring Dr.Fixit Pidigrout5M(or equivalent BASF /
FOSROC / STP) (expansive, non-shrinking grout)
in the gaps around the plumbing pipes or joints on
through pre-wetted condition with water and
attaining a SSD condition..Providing and applying
one coat of polymer
38
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
Providing and laying 140-160 gsm geo-textile
fleece on top of Dr Fixit Solyseal.For protection of
waterproofing treatment screed / brick bat coba /
china mosaic / light weight concrete to be provided
at extra cost as per site requirement. Note:Â The
above jobs is to be done by the authorised
applicator of the manufacturer / authorised (PWD)
distributor with guarantee on bond paper for five
years
Spec. No.: As directed by Engineer-in-charge
19 For RCC Slab : Mechanically clean the RCC slab
and wall with wire brush / coir brush to free from
all loose materials like dust, dirt etc. Make wattah /
coving of 50x50 mm at all horizontal & vertical
joints to avoid right angle turning. Seal all
honeycombs, pin holes, joints, pipe outlets with
Polymer Modified Mortar. Providing and applying
one coat primer with Dr Fixit Torchshield
Primer(or equivalent Texsa / FOSROC / STP).Â
Solvent based bitumen modified primer
conforming to ASTM D-41 to be used to seal and
prepare the substrate prior to the installation of
Dr.Fixit Torchshield (or equivalent Texsa / BASF /
FOSROC / STP). Providing and applying Dr Fixit
Torchshield (with elongation break up as per EN-
12311-1 = L-40% T-40%, Tensile strength (N/5cm)
= L-700 & T=450, Tear strength as per ASTM –
D5147 = L-300 N & T-250N, Cold flexibility as per
EN-1109 (upto2o C) = -5, Softening point as per
EN-1110 (oC) <150, water absorption as per EN-
1928 = -0.15% Max) (or equivalent Texsa /BASF /
FOSROC / STP).with proper alignment and
minimum overlap of100MM with proper application
39
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
brick bat coba / china mosaic / light weight
concrete to be provided at extra cost as per site
requirement. 3 mm Thick Note:Â The above jobs
is to be done by the authorised applicator of the
manufacturer / authorised (PWD distributor with
guarantee on bond paper for five years
Spec. No.: As directed by Engineer-in-charge
40
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
21 vaccum cleaning if required. All surface cracks Sq.Mt. 749.00 0.00
upto 5mm width will be filled up with Dr.Fixit
Crack X Paste (or equivalent BERGER/ ASAIN /
BASF / FOSROC / STP) . The external surfaces
will be primes with Dr.Fixit Primeseal(or
equivalent BASF / FOSROC / STP) diluted with
potable water in the ratio of 2:1 by volume
prior to application of Dr.Fixit Newcoat or
equivalent ( BASF / FOSROC / STP) . Allow it to
dry for at least 2 to 3 hours and then apply Dr.Fixit
Newcoat (As per technical data enclosed with
BOQ)Apply three coats of Newcoat with different
shades colors for better monitoring with time
interval of 6-8 hrs between each coat.The
application of each coat shall be in perpendicular
direction to the subsequent coat. Allow Newcoat to
air cure for 3 to 4 days before subjecting to use /
foot traffic. Allow it to air cure for 7 days and (do
not dilute Dr.Fixit Newcoat by any means). Note:Â
The above jobs is to be done by the authorised
applicator of the manufacturer / authorised (PWD)
distributor with guarantee on bond paper for five
years
Spec. No.: As directed by Engineer-in-charge
22 For Wet Areas with Bath Seal : Mechanically Sq.Mt. 799.00 0.00
clean the RCC slab surface and side walls with
wire brush / coir brush to free from all loose
materials like dust, loose particles, dirt, etc. Seal
all honeycombs, pin holes, joints, pipe outlets with
Polymer Modified Mortar (1:5:10) Also apply,Â
around all PVC / CI pipes fixed in toilet
waterproofing system Dr Fixit Bathseal Tape(or
equivalent BASF / FOSROC / STP) / Crack
Bridging ability is >1.5 MM as per ASTM C 838 ),
a non reinforced twin side adhesive bitumen
41
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
membrane comprising of polymerised bitumen,
sandwiched between plastic released films on
either side, then usingDr.Fixit Pidigrout 5M(
expansive, non-shrinking grout) in the gaps
around the plumbing pipes where bathseal tape
has been used, after attaining a SSD condition.
Making first coat of Dr Fixit Pidifin 2K(or
equivalent BASF / FOSROC / STP) (Sp.Gravity
@30 Degree, g/cc is 1.65+ 0.10 / Abrasion
resistance, cm/km is 0.09 / rapid chloride
permeability reduction in chloride ion penetration,
is 90% as per ASTM C 1202: 1997 / properly
rendered, cleaned RCC slab &side walls with
brush and allow it to dry for 6-8 hrs. After drying of
first coat, apply second coat and sprinkled coarse
sand on vertical surface. The Pidifin 2K Coating
should continue up to 4 feet above finished floor
level. Allow 24 hrs for full cure. Apply 12-15 mm
waterproof plaster on slab & vertical surface
before admixed with Dr Fixit Pidiproof
LW+(or equivalent BASF / FOSROC / STP)
IS2645 Dosage200ml per bag of cement. Cure the
surface with water. Note:Â The above jobs is to
be done by the authorised applicator of the
manufacturer / authorised (PWD) distributor with
guarantee on bond paper for five years
Spec. No.: As directed by Engineer-in-charge
42
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
Providing and applying one coat primer with Dr
Fixit Torchshield Primer (or equivalent Texsa /
FOSROC / STP). Solvent based bitumen
modified primer conforming to ASTM D-41 to be
used to seal and prepare the substrate prior to the
installation of Dr.Fixit Torchshield Mineral Finish
Green Color (or equivalent Texsa / BASF /
FOSROC / STP). Providing and applying Dr Fixit
Torchshield Mineral Finish Green Color (with
elongation break up as per EN-12311-1 = L-40% T-
40%, Tensile strength (N/5cm) = L-700 & T=450,
Tear strength as per ASTM – D5147 = L-300 N
& T-250N, Cold flexibility as per EN-1109 (upto2o
C) = -5, Softening point as per EN-1110 (oC)
<150, water absorption as per EN-1928 = -0.15%
Max) (or equivalent Texsa /BASF / FOSROC /
STP).with
proper alignment and minimum overlap of100MM
with proper application method, For protection of
waterproofing treatment screed / brick bat coba /
china mosaic / light weight concrete to be provided
at extra cost as per site requirement. Note:Â The
above jobs is to be done by the authorised
applicator of the manufacturer / authorised (PWD
distributor with guarantee on bond paper for five
years For 3 mm thk Mineral finish Green Color
Spec. No.: As directed by Engineer-in-charge
43
Bd - J : Water Proofing
ITEM Description Final Rate (2015-16)
Unit Completed Labour
NO.
1 2 3 4 5
24 Fixing of Dr Fixit Waterbar SW2020(or equivalent Sq.Mt. 599.00 0.00
BASF / FOSROC / STP) on all construction joints
like slab & wall, lift joints etc during concreting
work is on. Mechanically clean the RCC slab and
wall with wire brush / coir brush to free from all
loose materials like dust, dirt etc. Seal all
honeycombs, pin holes, joints with Polymer
Modified Mortar attain SSD condition.Apply first
coat of Dr Fixit Pifin2k(or equivalent BASF /
FOSROC / STP) rapid chloride permeability
reduction in chloride ion penetration, is 90% as
per ASTM C 1202: ]on properly rendered, cleaned
RCC slab & wall with brush and allow it to dry for 6-
8 hrs.After drying of first coat apply second coat
and sprinkled coarse sand on vertical surface.
Allow 24 hrs for full cure.Apply waterproof screed
concrete 30-40
44
Bd - K : Expansion Joints
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing expansion joints in R.C.C. framed Sq.Mt. 2851.00 433.00
structure (interior column) with plain premoulded
filler 25 mm thick including fixing T.W. battens on
both faces and finishing as directed etc. Complete.
Spec. No.: Bd.K.1 Page No. 357
45
Bd - K : Expansion Joints
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
6 Providing expansion joints in R.C.C. framed Sq.Mt. 5015.00 675.00
structure (exterior column) with plain premoulded
filler 25 mm thick with 40 mm wide and 1 mm thick
stainless steel plate, hold fast, fixing T.W.
battens on internal face and finishing etc.
complete.
Spec. No.: Bd.K.1 B Page No. 357
7 Providing expansion joints in R.C.C. framed Sq.Mt. 4491.00 578.00
structure (at floor level) with plain premoulded
filler 25 mm thick with 40 mm wide and 1 mm thick
stainless steel plate, hold fast, fixing T.W.
battens of internal face and finishing etc.
complete.
Spec. No.: Bd.K.1 C Page No. 357
8 Providing expansion joints in R.C.C. framed Sq.Mt. 4575.00 482.00
structure (at Terrace level) with premoulded filler
25 mm thick with 40 mm wide and 1 mm thick
stainless steel plate as required, bitumen poured
filler and fixing T.W. battens on inner faces
finishing etc. complete as directed.
Spec. No.: Bd.K.1 D Page No. 357
46
Bd - K : Expansion Joints
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
10 Providing and fixing of BITUFLEX CLOSE CELL R.Mt. 1577.00 147.00
FOAM of size 30 mm x 30 mm in double layer in
the expansion joints in R.C.C. framed structure
(Exterior column) with closed cell foam , applying
TP-40 PRIMER on both the sides of concrete
surface, filling the 25 mm x 25 mm gap with the
POLYSEAL, highly flexible sealant and covering
the joint with Polydee- LM, 150 mm width in 2
coats and fixing the aluminium plate of 100 mm
wide and 3 mm thick on external face of column
etc. complete.
Spec. No.: As directed by Engineer in charge.
47
Bd - L : Plastering and Pointing
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing internal cement plaster 6 mm thick in a
single coat in cement mortar …………………….
to concrete surface in all positions including
scaffolding and curing complete.
Spec. No.: Bd.L.1 Page No. 363
48
Bd - L : Plastering and Pointing
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
5 Providing sand faced plaster externally in Sq.Mt. 411.00 246.00
cement mortar using approved screened sand, in
all positions including base coat of 15 mm thick in
cement mortar 1:4 using waterproofing
compound at 1 kg per cement bag curing the
same for not less than 2 days and keeping the
surface of the base coat rough to receive the
sand faced treatment 6 to 8 mm thick in cement
mortar 1:4 finishing the surface by taking out
grains and curing for fourteen days scaffolding
etc.complete.
Spec. No.: Bd.L.7 Page No. 368
6 Providing rough cast cement plaster externally in Sq.Mt. 336.00 197.00
two coats to concrete, brick or stone masonry
surfaces in all positions with base coat of 12 to
15 mm thick in C.M. 1:4 and rough cast treatment
12mm thick in proportion 1:1 1/2:3 including
scaffolding and fourteen days curing complete.
Spec. No.: Bd.L.8 Page No. 368
49
Bd - L : Plastering and Pointing
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
10 Providing tuck pointing with cement mortar 1:3 Sq.Mt. 124.00 89.00
for stone masonry including scaffolding and
curing complete.
Spec. No.: Bd. L. 16 Page No. 372
11 Providing weathered pointing with cement Sq.Mt. 120.00 89.00
mortar 1:3 for stone masonary including
scaffolding and curing complete.
Spec. No.: Bd. L. 17 Page No. 372
12 Providing 'V' groove pointing with cement Sq.Mt. 95.00 74.00
mortar 1:3 for stone masonry / brick masonry
including scaffolding and curing complete
Spec. No.: Bd. L. 18 Page No. 372
13 Providing fine cement finish 1.5 mm thick over Sq.Mt. 48.00 35.00
green plaster surface including scaffolding curing
etc. complete.
Spec. No.: As directed by Engineer in charge.
14 Labour charges for providing groove in external R.Mt. 20.00 19.00
plaster having width of 2.5 c.m. and spaced at a
distance of 45 c.m. etc. complete.
Spec. No.: As directed by Engineer in charge.
15 Providing patti ….. mm on plastered surface 12
mm to 15 mm thick in c.m. 1:3 line and level
including neat finishing scaffolding curing etc.
complete
Spec. No.: As directed by Engineer in charge.
a 75 mm R.Mt. 18.00 12.00
b 100 mm R.Mt. 26.00 18.00
c 150 mm R.Mt. 38.00 18.00
16 Providing and fixing chicken mesh jali (24 R.Mt. 92.00 6.00
gauge) at the junction of 2 different surfaces of
different material component at the time of
plastering to prevent cracking in plaster surface
as and where directed at all floors with all leads
and lifts etc. complete.
Spec. No.: As directed by Engineer in Charge:
50
Bd - L : Plastering and Pointing
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
17 Providing and applying plaster with plaster of Sq.Mt. 103.00 49.00
paris in 6mm thickness to previously plaster
surface in all position including preparing the
surface scaffolding etc. complete.
Spec. No.: As directed by Engineer in Charge.
18 Providing and applying spray plaster made with Sq.Mt. 172.00 32.00
finely graded marble and quartz in 2 mm
thickness in two coats using putty knife or trowel
to newly plaster fairly even surface after minimum
30 days gap in all position including finishing the
surface using zero number sand paper or fine
emry paper gently level the area by moving paper
in round circles removing the dust and clean the
surface with dry cloth and scaffolding including all
materials and labour etc. complete. (Prior
approval of Superintending Engineer is
Necessary)
Spec. No.: As directed by Engineer in Charge.
51
Bd - L : Plastering and Pointing
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
applying the mortar with steel float on the surface
in proper evenness applying at coat of white
cement and lime to set a smooth finish then
applying a thin coat of slurry made of white
cement and black oxide colour in required
proportion by the steel float to get black streaks
on the surface and curing the surface for two
days including all materials and labour etc.
complete. (Prior approval of Superintending
Engineer is Necessary)
Spec. No.: As directed by Engineer in Charge.
20 Providing and applying plaster / wall punning with Sq.Mt. 330.00 133.00
plaster of paris ( with plaster of paris material of
Ambuja / Mor /ACC or equivalent make ) in 10 to
13 millimeter thickness to previously plastered
surface / or on newly brick surface ( Excluding
rough cast plaster ) in all position including
preparing and Finishing the surface scaffolding
etc.complete.
Spec. No.: As directed by Engineer in charge.
52
Bd - L : Plastering and Pointing
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
22 Providing and applying Texture plaster with Sq.Mt. 502.00 222.00
finishing with With Purlina / Rustic texture
material ( with texture material of Asian /
Renava/Nitco/Temtex or equivalent company
make ) in 3 to 4 millimeter thickness on
previously finished plastered surface ,including
Plaster Groove 6mm thickness or Tape Grooves
35 to 45 mm thickness or as required, in all
position including preparing the surface
scaffolding etc.complete. ( Excluding Texture
Paint and Texture Paint Finishing )
Spec. No.: As directed by Engineer in charge.
53
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 a Providing and laying Rough Shahabad Stone
Flooring ..............mm thick and of required width in
plain/ diamond pattern on a bed of 1:6 C.M. including
cement float, striking joints, pointing in cement
mortar 1:3 curing and cleaning etc. complete.
Spec. No.: Bd.M.1 Page No. 301
54
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
5 Providing and laying Semipolished Kota stone Sq.Mt. 955.00 265.00
flooring over 20mm (average) thick and required
width in plain/ diamond pattern on bed of 1:6 Cement
mortar including cement float, filling joints with neat
cement slurry with pigment to match the shade
curing, polishing and cleaning complete. (Without
Polished)
Spec. No.: Bd.M.3 Page No. 383
6 Providing and laying Polished Kota stone flooring Sq.Mt. 1456.00 431.00
With Hand Cut Polished Kota Stones 25mm to
30mm thick and required width in plain/diamond
pattern on bed of 1:6 Cement mortar including
cement float, filling joints with neat cement slurry,
curing, cleaning and Mirror Polishing complete.
Specifications: Bd.M.3 Page No. 380
Spec. No.: Bd. M-3 page No. 383
55
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
9 Providing and laying polished machine cut Kota Sq.Mt. 1130.00 426.00
stone slabs 20 mm (average) thick for treads and
risers of steps and staircases, with rounded nosing
and antiskid lining for the treads on a bed of 1:4
cement mortar including cement float, filling joints
with neat cement slurry, curing, if required hand
polishing and cleaning complete.
Spec. No.: Bd.M.22 Page No. 395
10 Providing and laying ............... glazed tiles of
148.5x148.5/ 300x300/300x200/200x100mm in size
and 5 to 6 mm thick for flooring in required
positions and laid on a bed of cement mortar 1:4
including neat cement float, filling joints with white
cement slurry, curing and cleaning etc. complete.
(Including all specials required like round edge titles,
corner cups ,etc.) (with white cement)
Spec. No.: BdF-12 Page No. 389
56
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
12 Providing and laying Ceramic tiles of Somany/RAK/
Kajaria/ Nitco/ Asian or equivalent make having size
.............. cm of first quality (thickness to be specified
by the manufacturer )and conforming to IS 15622-
2006 for flooring in required position laid on a bed
of 1:4 cement mortar including cement float, filling
joint with white/colour cement slurry cleaning curing
complete. Spec. No.: BdF-13 Page No. 389
Spec. No.:As directed by Engineer-in-Charge.
14 Providing and laying Ceramic mat finish tiles of Sq.Mt. 1312.00 274.00
Somani/ Kajaria/ Nitco/ Jonson or equivalent make
(conforming to IS 15622) of first quality having size
60 cm x 60 cm of approved colour for flooring in
required position laid on a bed of 1:4 cement mortar
including cement float, filling joint with white/colour
cement slurry cleaning curing complete.
57
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
15 Providing and laying ceramic tiles of
Somani/RAK/Kajaria / Nitco /Asian or equivalent
make of first quality ,having size 30 cm. x 30 cm. for
dado and skirting in required position with
readymade adhesive mortar of approved quality on
plaster of 1:3 cement mortar including joint filling with
white/ colour cement slurry cleaning curing
complete.
Spec. No.:As directed by Engineer-in-Charge.
Spec. No.: BdM-13 Page No. 389
a 30cm x 30 cm Sq.Mt. 964.00 343.00
b 30cm x 45 cm Sq.Mt. 1151.00 343.00
c 45cm x 45 cm Sq.Mt. 1230.00 405.00
d 30cm x 60 cm Sq.Mt. 1028.00 220.00
e 60cm x 60 cm Sq.Mt. 1301.00 430.00
16 Providing and laying Ceramic mat finish tiles of
Somani/RAK/ Kajaria/ Nitco/ Asian or equivalent
make conforming to IS 15622 first quality (thickness
to be specified by the manufacturer ) having size 60
cm x 60 cm of first quality of approved colour for
skirting & dado in required position on plaster of 1:3
cement mortar including cement float, filling joint with
white/colour cement slurry cleaning curing complete.
Spec. No.: BdM-13 Page No. 389
58
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
18 Providing and laying vitrified ...........finish decorative
type Somani/RAK/ Kajaria/ Nitco/ Asian or
equivalent make first quality tiles having
size.............cm (thickness to be specified by the
manufacturer )and confirming to IS. 15622-2006 of
approved shade and pattern for flooring in required
position laid on a bed of 1:4 cement mortar including
neat cement float, filling joints, curing and clearing
etc. complete. (Prior Approval of SE is necessary)
Spec. No.: Bd.M. 12 Page No.389
59
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
b 150 mm RMt. 220.00 46.00
21 Providing and laying vitrified matt finish tiles of
Somany /RAK/ Kajaria/ Nitco/ Asian or equivalent
make of first quality having size 800mm x
800mm(thickness to be specified by the
manufacturer ) and confirming to IS. 15622-2006 of
approved make, shade and pattern for skirting .......
mm in required position laid on a bed of 1:4 cement
mortar including neat cement float, filling joints,
curing and cleaning etc. complete. Spec. No.:
Bd.M.12 Page No. 389
a 100 mm Rmt. 173.00 33.00
b 150 mm Rmt. 260.00 50.00
22 Providing and laying Vitrified mirror/glossy finish Sq.Mt. 1320.00 26.00
tiles of Somany /RAK/ Kajaria/ Nitco/ Asian or
equivalent make and first quality ,decorative type of
size 590 millimeter to 605 millimeter x 590 millimeter
to 605 millimeter(thickness to be specified by the
manufacturer )(on a existing flooring) with bonding
chemical and confirming to IS 15622-2006 of
approved make shade and pattern for flooring in
required position laid on a bed of bonding chemical
filling joints curing and cleaning etc complete.(prior
approval of SE is necessary)
Spec. No.: Bd. M-12 page No. 389
23 Providing and laying Vitrified MATT finish tiles of Sq.Mt. 1380.00 78.00
Somany /RAK/ Kajaria/ Nitco/ Asian or equivalent
make decorative type of size 590 millimeter to 605
millimeter x 590 millimeter to 605 millimeter
(thickness to be specified by the manufacturer )(on a
existing flooring) with bonding chemical and
confirming to IS 15622-2006 of approved make
shade and pattern for flooring in required position
laid on a bed of bonding chemical filling joints curing
and cleaning etc complete. (prior approval of SE is
necessary)
Spec. No.: Bd. M-12 page No. 389
60
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
24 Providing and laying in position flooring of Sq.Mt. 3158.00 270.00
telephone black / Amba White / Cat bary brown / RBI
red / Ocean Brown granite stone of first quality
approved shade and size 18 mm to 20 mm thick on
bed 1:4 cement mortar including colour cement
slurry to match the colour of slab polishing ,curing
and cleaning etc. complete. (Excluding polishing)
.(prior approval of SE is essential) Spec. No.: Bd.M.
12 B/Page No. 389
25 Providing and laying in position skirting ......... mm
of telephone black / Amba White / Cat bary brown /
RBI red / Ocean Brown granite stone of first quality
approved shade and size 18 mm to 20 mm thick on
bed 1:3 cement mortar including colour cement
slurry to match the colour of slab polishing ,curing
and cleaning etc. complete. (Excluding polishing)
(prior approval of SE is essential) Spec. No.: Bd.M.
12 B/Page No. 389
a 100 mm Rmt. 315.00 28.00
b 150 mm Rmt. 472.00 42.00
26 Providing and laying machine cut white / coloured Sq.Mt. 2605.00 155.00
marble slab 60 x 45 cm and 20 mm thick of
approved quality, vein and colour for flooring in
required pattern on a bed of 1: 4 cement mortar
including neat cement float, filling joints with
white/coloured cement slurry, curing, polishing and
cleaning complete..(prior approval of SE is essential)
Spec. No.: BdM-16 Page No. 391
27 Providing and laying machine cut white / coloured Sq.Mt. 2660.00 219.00
marble slab 60 x 45 cm and 20 mm thick of
approved quality, vein and colour for dado and
skirting in required pattern on a bed of 1: 4 cement
mortar including neat cement float, filling joints with
white/coloured cement slurry, curing, polishing and
cleaning etc. complete.
Spec. No.: BdM-17 Page No. 391
61
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
28 Providing sills of polished Kota stone 20 mm to
25mm thick, on a bed of 1:4 cement mortar including
cement float, filling joints with slurry, curing polishing
and cleaning complete.
Spec. No.: Bd.M.29 Page No. 397
a Kota stone Sq.Mt. 1030.00 302.00
b Kadappa stone Sq.Mt. 710.00 183.00
29 Providing and fixing green marble of 18 to 20 mm
thick for door frame/window box frame etc. On
C.M. 1:6 including filling joints with polymer base
filler nosing the sharp edges wherever necessary,
curing, etc. complete.
Spec. No.: Bd. M. 12 Page No. 389
a green marble Sq.Mt. 2427.00 931.00
b granite stone telephone black / Amba White / Sq.Mt. 3516.00 733.00
Cadburybrown / RBI red / Ocean Brown granite
stone
30 Providing and fixing black kadappa stone shelves Sq.Mt. 767.00 198.00
25mm. thick machine polished, extending the polish
upto 20 cm width on lowerside, rounding corners,
laying in position jointing with cement mortar 1:4
proportion curing etc complete.
Spec. No.: Bd.M.29 Page No. 397
62
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
32 Providing and fixing machine cut mirror ...................
polished 18 mm to 20 mm thick telephone black
granite / Amba White / Cat bary brown / RBI red /
Ocean Brown stone partition with rounding the
edges etc. complete. A) Both side polish
Spec. No.: Bd.M.35 B/Page No.399
34 Providing and fixing machine cut machine polished Sq.Mt. 3243.00 383.00
18 mm to 20 mm thick telephone black / Amba White
/ Cat bary brown / RBI red / Ocean Brown granite
stone for treads and risers of steps and staircases
of approved colour and shade with rounded
moulding and three grooved line for the treads on
bed of 1;4 Cement mortar including float filling joints
with neat cement slurry curing polishing and
cleaning etc. complete..(prior approval of SE is
essential)
Spec. No.: Bd. M.22 B/Page No. 395
63
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
35 Providing and laying white / approved colour marble Sq.Mt. 2870.00 248.00
slabs 20 mm thick of approved quality, colour and
veins, for treads and risers of steps and staircases
in one piece with round nosing & engraving three
lines for treads on bed of 1:4 cement mortar
including rounded nosing for the treads, neat cement
float, filling joints with cement slurry to match colour
of the slabs, curing, polishing and cleaning etc.
complete. (Prior approval of S.E. is necessary)
Spec. No.: BdM-26 Page No. 396
64
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
38 Providing treatment of TREMIX VACCUM
dewatering over cement concrete M-25 surface
.......... mm including fixing of M.S. channel
framework as per required size and placing of dowel
rods, vibrating the concrete by needle vibrator and
leveling by tremix double beam surface vibrator,
dewatering through sunction matt of tremix system,
power floating by skin floater and power trowelling to
obtain required level, surface cleaning including
procuring three phase tempoarary electric supply /
generator set if required at site for operating above
machinery etc. complete.(prior approval of SE is
nacessary) ( For Industrial Flooring)
Spec. No.: As directed by Engineer in charge
a 100 mm Sq.Mt. 739.00 70.00
b 150 mm Sq.Mt. 1070.00 104.00
39 Providing and fixing 1.5 mm thick polyvenyl venyl Sq.Mt. 477.00 8.00
chloride flooring including leveling the base with
white cement including pasting with appropriate
material cleaning the surface etc. complete.
(As direced by Enquncer inchec)
40 Providing and fixing heavy duty inter locking Sq.Mt. 925.00 58.00
concrete Gray / Colour antiskid paving blocks of 60
mm thickness of having a strength of 300 kg/Sq.cm.
of approved quality and shape on a bed of crushed
sand of 25 to 40 mm thick including compacting,
cleaning etc. complete. (prior approval of SE is
essential)
Spec. No.: A directed by Engineer in charge
41 Providing and fixing heavy duty inter locking Sq.Mt. 1059.00 64.00
concrete Gray / Colour antiskid paving blocks of 80
mm thickness of having a strength of 400 kg/Sq.cm.
of approved quality and shape on a bed of crushed
sand of 25 to 40 mm thick including compacting
cleaning etc. complete. (prior approval of SE is
essential)
Spec. No.: A directed by Engineer in charge
65
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
42 Providing Half-round Moulding ( Full Moulding ) to
18 mm to 20 mm thick …………………….. including
fine polishing and cleaning etc complete.
Specifications: As directed by Engineer-In- Charge
Spec. No.: As directed by Engineer-In- Charge
66
Bd - M : Paving, Flooring and Dado
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
47 Providing leather finished polishing to Granite Sq.Mt. 408.00 130.00
Stone slab by continuous grinding in 4 coats of
different bits to receive rough and matt finish
including buffing process before laying and fixing of
stone as per drawing and design, including cleaning,
washing and finishing etc. complete.
Spec. No.: As directed by Engineer in charge
48 Providing leather finished polishing to Marble Sq.Mt. 373.00 106.00
Stone slab by continuous grinding in 4 coats of
different bits to receive rough and matty finish
including buffing process before laying and fixing of
stone as per drawing and design, including cleaning,
washing and finishing etc. complete.
Spec. No.: As directed by Engineer in charge
67
Bd - N : Wood Finishes
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing and applying boiled linseed oil in one Sq.Mt. 12.00 6.00
coat, preparing the surface, scaffolding etc.
complete as directed.
Spec. No.: Bd. N. 1. 1 Page No. 409
2 Providing and applying boiled linseed oil in two Sq.Mt. 19.00 11.00
coats to the new wood work, including knotting,
preparing the surface, scaffolding etc. complete
as directed.
Spec. No.: Bd.N.1.1 Page No. 409
3 Providing and applying Wax polishing to the Sq.Mt. 25.00 20.00
new wood work including knotting, preparing
the surface, scaffolding etc. complete as
directed.
Spec. No.: Bd.N.1.2 Page No. 409
4 Providing and applying Wax polishing to the Sq.Mt. 20.00 12.00
old wood work including knotting, preparing the
surface, scaffolding etc. complete as directed.
Spec. No.: Bd. N. 1.2 Page No. 409
68
Bd - N : Wood Finishes
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
9 Providing and applying melamine polish of Sq.Mt. 655.00 277.00
required finish to the wood work by spray
machine including knotting and preparing the
even surface by scraping, applying French
polishing, scaffolding if required etc. complete.
Note:The work to be executed on pre-approval
of Superintending Engineer.
Spec. No.: As directed by Engineer-in charge.
69
Bd - O : Oil Painting
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing and applying two coats of lead/zinc Sq.Mt. 51.00 12.00
base oil paint/ bituminous paint of approved
colour and shade to new wood work and fiber
boards including preparing the surface, knotting,
scaffolding if necessary, excluding primer coat
complete.
Spec. No.: Bd.O. 1 Page No. 409
2 Providing and applying .............. of lead/zinc
base oil paint/ bituminious paint of approved
colour and shade to old wood work previously
painted and fiber boards including if necessary
scaffolding, preparing surface excluding primer
coat complete.
Spec. No.: Bd.0.2 Page No. 409
a one coat Sq.Mt. 27.00 6.00
b two coats Sq.Mt. 41.00 12.00
3 Providing & applying two coats of lead/zinc base Sq.Mt. 50.00 13.00
oil paint/ bituminious paint of approved colour to
new structural steel work and iron work in
buildings including scaffolding if necessary,
cleaning and preparing the surface. (excluding
primer coat).
Spec. No.: Bd.0.3 Page No. 409
4 Providing and applying ……………... of
aluminium paint of approved make to new
structural steel work in building and workshop
including scaffolding if necessary, cleaning and
preparing surface (excluding primer coat)
complete.
Spec. No.: Bd.0.4 Page No. 409
a one coat Sq.Mt. 43.00 9.00
b Two coats Sq.Mt. 61.00 16.00
5 Providing and applying two coats of synthetic Sq.Mt. 54.00 16.00
enamel paint of approved colour to new /old
structural steel work and wood work in buildings,
including scaffolding if necessary, cleaning and
preparing the surface (excluding primer coat)
complete.
Spec. No.: Bd.0.5 Page No. 409
70
Bd - O : Oil Painting
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
6 Providing and applying .............. of flat oil paint
of approved colour to the old structural steel
work and iron work previously painted in building
including scaffolding, if necessary, cleaning and
preparing surface(excluding primer coat)
complete.
Spec. No.: Bd.0.6 Page No. 406
8 Providing and applying two coats of water proof Sq.Mt. 41.00 17.00
cement paint of approved manufacture and of
approved colour to the plastered surfaces
including scaffolding if necessary, cleaning and
preparing the surface, watering for two days
complete.
Spec. No.: Bd.0.8 Page No. 409
9 Removing old paint from steel and other metal Sq.Mt. 8.00 8.00
surfaces and making the surfaces even with hand
scrapping, scaffolding etc. complete.
Spec. No.: As directed by Engineer in charge.
10 Providing and applying priming coat over new Sq.Mt. 19.00 4.00
wood and wood based surfaces, including
preparing the surface by thoroughly cleaning oil,
grease, dirt and other foreign matter, sand
papering and knotting, scaffolding etc. complete.
Spec. No.: As directed by Engineer in charge.
71
Bd - O : Oil Painting
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
11 Providing and applying priming coat over Sq.Mt. 16.00 7.00
new/old steel and other metal surfaces including
preparing the surface by thoroughly cleaning oil,
grease, dirt and other foreign matter and scoured
with wire brushes, fine steel wool, scrappers and
sand paper, scaffolding etc. complete.
Spec. No.: As directed by En-gineer in charge.
13 Providing and applying one coat of seal cement Sq.Mt. 15.00 10.00
primer of approved manufacture and shed
including scaffolding preparing the surface by
cleaning dirt and other foreign matters, scraping if
necessary including scaffolding etc. complete.
Spec. No.: As directed by Engineer in charge.
14 Providing and applying pearl/ luster finish paint Sq.Mt. 212.00 98.00
of approved colour and shade to the existing
internal wall surface including scaffolding,
preparing the surface, applying the acrylic wall
putti etc. complete.
Spec. No.: As directed by Engineer in charge.
15 Providing and applying two coats of external Sq.Mt. 198.00 32.00
textured synthetic paint of approved shade and
quality and one coat of primer before applying
textured paint including scaffolding if necessary
preparing surface by thoroughly cleaning oil,
grease, dirt and other materials as required, etc.
complete
Spec. No.: As directed by Engineer in charge.
72
Bd - O : Oil Painting
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
16 Providing and applying two coats of Appex Ace Sq.Mt. 127.00 29.00
exterior paint of approved manufacture and of
approved colour to the plastered surfaces
including cleaning ,preparing the plaster surface
,applying primer coat ,scaffolding if necessary ,
and watering the surface for two days complete
Spec. No.: As directed by Engineer in charge.
73
Bd - P : Colour / White Washing & Distempering
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
1 Providing and applying white-wash in one coat on
old / new plastered or masonry surfaces and
asbestos cement sheets including scaffolding and
preparing the surface by brushing & brooming down
complete.
Spec. No.: Bd.P.1 Page No. 423
a one coat Sq.Mt. 5.00 3.00
b two coats Sq.Mt. 7.00 3.00
2 Providing & applying washable oil-bound
distemper of approved colour and shade to old &
new surfaces in ………….. including scaffolding,
preparing the surfaces. (excluding the primer coat.)
complete.
Spec. No.: Bd. P.5 Page No. 428
a one coat Sq.Mt. 24.00 5.00
b two coats Sq.Mt. 35.00 7.00
3 Providing and applying plastic emulsion paint of Sq.Mt. 64.00 11.00
approved quality, colour and shade to old & new
surfaces in two coats including scaffolding,
preparing the surface. (excluding the primer coat)
complete.
Spec. No.: Bd.P.6 Page No. 428
4 Removing white wash or colour wash by steel Sq.Mt. 4.00 4.00
wire brushing and / or scrapping sand preparing
and preparing the wall surface smooth including
necessary repairs to scratches etc. complete.
Spec. No.: As directed by Engineer in charge.
5 Extra for washing and cleaning of decorated wall Sq.Mt. 2.00 2.00
surfaces with soap, soda and water.
Spec. No.: As directed by Engineer in charge.
6 Providing and applying primer coat of approved Sq.Mt. 17.00 9.00
quality to old/new wall surface to receive oil bound
distemper treatment/plastic emulsion, including
scaffolding, preparing the surface as directed etc.
completed.
Spec. No.: As directed by En-gineer in charge.
74
Bd - Q : Wood Work
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 Providing and fixing Ghana teak wood planking
………. thick for flooring plained on both sides,
tounged and grooved including scaffolding, if
necessary, and one coat of primer complete.
Spec. No.: Bd.Q. 1 Page No. 431
a 25 mm thick Sq.Mt. 2130.00 78.00
b 50 mm thick Sq.Mt. 4080.00 76.00
2 Providing and fixing Ghana teak wood joists and Cu.Mt. 90030.00 818.00
girders in timber floors of single, double or framed
type including scaffolding if necessary, and one
coat of primer complete.
Spec. No.: Bd.Q.2 Page No. 436
3 Providing and fixing Jungle (hard) wood of Cu.Mt. 37377.00 2887.00
approved species joists and girders in timber floor
of single, double or framed type including
scaffolding if necessary and one primer coat
complete.
Spec. No.: Bd.Q.2 Page No. 436
4 Providing and fixing Ghana teak wood plank Sq.Mt. 1960.00 127.00
ceiling 20 mm thick tounged and groved including
iron screws, scaffolding, if necessary, including one
primer coat on under side and one coat of coal tar
on upper side complete.
Spec. No.: Bd.Q.3 Page No. 438
5 Providing and fixing Ghana teak wood framed Cu.Mt. 92320.00 18866.00
collar beam / king post / queen post truss, with all
Iron work including scaffolding, if necessary, and
one coat of primer complete.
Spec. No.: Bd.Q.4, Page No. 439
6 Providing and fixing in jungle wood framed collar Cu.Mt. 48584.00 17797.00
beam / king post / queen post truss, with all iron
work including scaffolding, if necessary and primer
coat complete.
Spec. No.: Bd.Q.4, Page No. 439
75
Bd - Q : Wood Work
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
7 Providing and fixing ............................ common
rafters, purlins and purlin cleats, hip rafters, jack
rafters, ridges, wall plates, post plates and posts for
roofing etc. including scaffolding, if necessary, all
iron work and one coat of primer complete.
Spec. No.: Bd.Q.5, Page No. 439
10 Providing and fixing Ghana teak wood eaves RMt. 433.00 101.00
boards 15 cm wide and 25 mm thick plain
decorative type including scaffolding and painting
with two coats complete.
Spec. No.: Bd.Q. 19 Page No. 449
11 Providing and fixing seasoned and treated jungle R.Mt. 205.00 69.00
wood of approved species eaves board 15 cm
wide and 25 mm thick plain decorative type
including scaffolding and painting with two coats
complete.
Spec. No.: Bd.Q. 19 Page No. 449
76
Bd - Q : Wood Work
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
12 Providing and fixing Ghana Teak wood eaves plate R.Mt. 253.00 60.00
of size 10cm wide and 20 mm thick including
scaffolding and painting in two coats com-plete.
Spec. No.: Bd.Q.20 Page No. 450
13 Providing and fixing Ghana Teak wood barge R.Mt. 533.00 101.00
board 22 cm wide and 20mm thick plain type
including scaffolding and painting in two coats
complete.
Spec. No.: Bd.Q.21 Page No. 450
14 Providing and fixing seasoned and treated jungle R.Mt. 240.00 77.00
wood of approved species barge board 22 cm
wide and 20 mm thick plain type including
scaffolding and painting in two coats complete.
Spec. No.: Bd.Q.21 Page No. 450
15 Providing and fixing Shutter to wall Cupboard Sq.Mt. 2515.00 95.00
consisting of Ghana Teak Wood styles and Rails
25 mm thick and 75 mm wide with panel insert of
12mm Waterproof & termite proof plywood with
one approved coloured Laminated Face on one
side 1.5 mm thick, bonded with Phenol
Formaldehyde Synthetic Resin including Lipping
Beading. Iron oxidised fixtures and fastening and oil
primer coat etc. complete. (Excluding cupboard
frame)
Spec. No.: As directed by Engineer in charge.
16 Providing and fixing in position P.V.C.. hand rail of R.Mt. 390.00 70.00
approved quality as per IS Std. make and shade, as
per detailed drawings or as directed by the
Engineer-in-charge, including French polishing etc.
complete.(50mm size)
Spec. No.: As directed by Engineer in charge.
17 Providing and fixing Ghana Teak wood skirting 20 Sq.Mt. 2730.00 828.00
mm thick in required position and of the size shown
in the drawings, including all mouldings as per
drawings, rough grounds, rawal plugs if necessary
and finishing with French polish etc. complete.
Spec. No.: BdQ-10 Page No. 443
77
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
1 Providing and fixing Mangalore tiled roofing with Sq.Mt. 692.00 53.00
class " AA" tiles including securing the last course
of tiles near the eaves with steel flat 40 mm x 3 mm
and 1.22 mm wire fixing 50 mm x 25 mm horizontal
teak wood battens and iron works and oiling the
battens etc. complete. (Excluding ridge and hip
tiles).
Spec. No.: Bd.R.1, Page No. 459
2 Providing and fixing Mangalore tiled roofing with Sq.Mt. 667.00 54.00
class "AA" tiles including securing the last course of
tiles near the eaves with steel flat 40 mm x 3 mm
and 1.22 mm wire fixing country teak wood sloping
battens of 25 x 12 mm teak wood horizontal
battens of 50mm x 25mm over the slopping battens,
all iron work and coal tarring the battens complete
(Excluding ridge & hip tiles)
Spec. No.: Bd.R.2, Page No. 462
3 Providing and fixing Mangalore tile ridge and hip R.Mt. 155.00 54.00
tiles of class "AA" including scaffolding if necessary,
pointing with coloured cement mortar and curing
complete.
Spec. No.: Bd.R.3, Page No. 463
4 Providing and fixing plain zinc sheeting of 0.80 mm Sq.Mt. 760.00 68.00
thick (22 B.W.G.) over the ridge hip or valley to
galvanized iron sheet roofing including all fastening
and bolt galvanised iror screws and bolts and lead
and bitumen washers complete.(Weight of 6.8
kg/sq.m.)
Spec. No.: Bd.R.5, Page No. 464
5 Providing and fixing corrugated galvanised iron Sq.Mt. 674.00 67.00
sheets of 0.63mm thick (24 B.W.G.) for roofing
without wind tiles including fastening with
galvanised / iron screw / bolt and lead / bitumen
washers as per drawing complete.(Weight of 5.5
kg/sq.m.)
Spec. No.: Bd.R.5, Page No. 464
78
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
6 Providing and fixing 6.00 mm thick Asbestos Sq.Mt. 443.00 73.00
Cement Corrugated (Big size) sheet roofing
including galvanised iron 'J' or 'L' hook bolts,
bituminous & G.I. washers, galvanised iron clamps
and bolts and nuts and scaffolding complete.
Spec. No.: Bd. R.7, Page No. 466
79
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
12 Providing and fixing frame work of anodised Sq.Mt. 809.00 325.00
aluminium sections for suspended false ceiling
consisting of aluminium T 50 mm x 40 mm weighing
0.39 kg/m. at 60 cms c/c & fixed with ( 15 x 15 mm)
flanges weighing 0.119 kg/m suspended on 6 mm
dia. mild steel rod weighing 0.22 kg/m fixed on wall
and beams including rounding of the edges with
aluminium T of 50 mm x 40 mm weighing 0.39 kg/m
etc. including all labour etc, complete.
Spec. No.: As directed by Engineer in charge.
13 Providing and fixing frame work of galvanised iron Sq.Mt. 625.00 365.00
for suspended false ceiling which includes
galvanised iron perimeter channels of size 27 mm &
0.5 mm thick having one flange of 20 mm and
another of 30 mm along with perimeter of the
ceiling, fixing in brick wall / partition with the help of
rawal plugs and screws, suspending galvenised
iron intermediate channels of size 45 mm and 0.9
mm thick with two flanges of 15 mm each from the
soffit at 1200 mm centers with steel galvanised iron
hanger of width 25 mm x 0.5 mm fasteners, ceiling
section of 0.5 mm thickness having curved wedge
of 51.5 mm and two flanges of 26 mm each with lips
of 10.5 mm fixed to the intermediate channel with
the help of connecting clips and in direction
perpendicular to the intermediate channel at 450
mmcenters,
12.5 mm dry walls screws at 230 mmcenters; fixing
screws mechanically either with screw driver or
drilling machine with suitable attachmentetc.
complete.
Spec. No.: As directed by Engineer in charge.
80
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
14 Providing and fixing false ceiling of teak wood Sq.Mt. 1086.00 190.00
particle board half perforated sheet 12 mm thick
including scaffolding, if necessary, all iron work and
two coats of oil painting to boards and beading i.e.
visible surface (excluding frame work and runners)
Spec. No.: Bd. R. 17 Page No. 473
16 Providing and fixing false ceiling of 12mm thick Sq.Mt. 1449.00 438.00
tabular Acoustic board of Armstrong/ Everest/
AMS or equivalent approved make, shape and
sizes as per drawings including powder coated G.I.
wall angle of 20mm x 20mm size, G.I. grid runners
of size 20mm x 38mm at 600mm center to center
both ways and suspended using G.I. wire 3mm wire
including fixing using butterfly clips and fasteners
including transporting, scaffolding all necessary
labour and machinery, finishing etc. complete.
Spec. No.: Bd. R. 19 Page No. 479
17 Providing and fixing false ceiling of 15mm thick Sq.Mt. 1541.00 385.00
Acoustic board of Armstrong/ Everest/ AMS (0.60 x
0.60 m.size ) or equivalent approved make, shape
and sizes as per drawings including powder coated
G.I. wall angle of 20mm x 20mm x 0.6mm size, G.I.
grid runners of size
81
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
20mm x 38mm at 600mm center to center both
ways and suspended using G.I. 3mm wire including
fixing using butterfly clips and fasteners including
transporting, scaffolding all necessary labour and
machinery, finishing etc. complete.
Spec. No.: As directed by Engineer in charge.
18 Providing and fixing false ceiling of T.W. partical Sq.Mt. 1113.00 116.00
board half perforated sheet 12 mm thick with frame
work of M.S. angle 40 x 40 x 5 mm and T of size 40
x 40 x 6 mm at 60 cm center to center including 12
mm dia. hangers, T.W. battens 50 x 25 mm and
beading 25 x 15 mm thick scaffolding, if necessary,
all iron work and two coats of painting to boards
and beading i.e. visible surface.
Spec. No.: Bd. R. 17, Page No. 472
20 Providing and fixing PVC False Ceiling consisting of Sq.Mt. 1068.00 146.00
600mm x 600mm, 3mm thick Plain PVC sheet used
as panel insert in a frame work made using
anodized aluminum Tee section 1 x1 gauge (25 x
25mm, 19 guage or 1mm thick) in square pattern of
grid sizes of 2’x2’(600x600mm). The aluminum
framework is Supported from the ceiling with the
help of G.I.
82
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
hook and G.I. wire / 6mm M.S. rods of required
sizes to maintain proper level etc. The aluminum
framework is supported on side wall with the use of
luminium1”x1” (25x25mm) angles. Complete as per
direction of Engineer-In-charge, manufacturer’s
specification & drawing. Spec. No.: As directed by
Engineer-in-charge
21 Providing and fixing false ceiling of Gypsum at all Sq.Mt. 932.00 320.00
height including providing and fixing of frame work
made of special sections, power pressed from M.S.
sheets and galvanized with zinc coating of 120
gms/sqm (both side inclusive) as per IS : 277 and
consisting of angle cleats of size 25 mm wide x 1.6
mm thick with flanges of 27 mm and 37 mm, at
1200 mm centre to centre, one flange fixed to the
ceiling with dash fastener 12.5 mm dia x 50 mm
long with 6 mm dia bolts, other flange of cleat fixed
to the angle hangers of 25x10x0.50 mm of required
length with nuts & bolts of required size and other
end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of
1200 mm centre to centre, to which the ceiling
section 0.5 mm thick bottom wedge of 80 mm with
ered flanges of 26 mm each having lips of 10.5 mm,
at 450 mm centre to centre, shall be fixed in a
direction perpendicular to G.I. termediate channel
with connecting clips made out of 2.64 mm dia x
230 mm long G.I. wire at every junction, including
fixing perimeter channels 0.5 mm thick 27 mm
83
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
channel with the help of dry wall screws of size 3.5
x 25 mm at 230 mm c/c, uding jointing and finishing
to a flush finish of tapered and square edges of the
board withrecommended jointing compound ,
jointing tapes , finishing with jointing compound in 3
layers covering upto 150 mm on both sides of joint
and two coats of primer suitable for board, all
complete as per drawings, specification and
direction of the Engineer in Charge
22 Providing and applying two coats of coal tar to roof Sq.Mt. 77.00 7.00
on new dungaree cloth one coat on each side etc.
complete as directed.
Spec. No.: As directed by Engineer in charge.
23 Providing and applying one coat of coal tar to roof Sq.Mt. 28.00 3.00
(without cloth) including scaffolding etc. complete
as directed.
Spec. No.: As directed by Engineer in charge.
24 Removing and resetting Mangalore tiles from roof Sq.Mt. 39.00 36.00
including refixing loose battens.
Spec. No.: As directed by Engineer in charge.
25 Removing the tiles, battens and dungry cloth from Sq.Mt. 38.00 37.00
roof, sorting out the serviceable and unserviceable
materials and stacking the same as and where
directed in the compound, scaffolding etc.
complete.
Spec. No.: As directed by Engineer in charge
84
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
27 Removing and lowering the roof truss carefully Sq.Mt. 146.00 140.00
without damaging the members and stacking as
and where directed in the compound including
scaffolding etc. complete.
Spec. No.: As directed by Engineer in charge.
28 Removing R.S. girders of any size and span M.T. 1083.00 1041.00
lowering the same and stacking neatly wherever
directed in the compound scaffolding etc. complete.
Spec. No.: As directed by Engineer in charge.
31 Providing and fixing sky light in R.C.C. roof Sq.Mt. 1717.00 77.00
including frame made of M.S. angle 50 x 50 x 6 mm
with hold fast, sheet glass 5 mm thick, Chicken
mesh 24 gauge with all accessories and required
fixtures and fastening fitting including painting etc.
complete.
Spec. No.: As directed by Engineer in charge.
32 Providing and fixing 12 mm dia. mild steel bar upto No. 82.00 53.00
0.5 M. length for anchor rods with necessary
threading nuts and bolts etc complete
Spec. No.: As directed by Engineer in charge.
33 Providing fixing Mangalore tile roofing with class Sq.Mt. 571.00 94.00
AA tiles in cement mortar 1:4 on sloping slab
including necessary scaffolding curing, finishing,
etc. complete.
Spec. No.: Bd. R. 3A., Page No. 460
85
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
34 Providing and fixing of precoated galvinized steel Sq.Mt. 842.00 45.00
profile sheet ( confirming to IS 14246 ) of TATA /
JINDAL or eqivalent make (size, shape & pitch of
corrugation as approved by Engineer-in-charge)
0.50mm (-/+ 0.05%) total coated thickness with zinc
coating minimux 120 gms per sq.mtr. as per IS 277,
in 240 mpa steel grade, 5-7microns eppoxy primer
on both side of the sheet and polyster top coat 15-
18 micorns and bottom minimum 7 microns. Sheet
should have protective guard film of 25 micorns
minimum to avoide scratches during transportation
and should be supplied in single length upto 12.0
meters or as directed by Engineer-in-charge. The
sheet shall be fix using self drilling / self tapping
screws of size(5.5 x 5.5mm) with EPDM seal,
complete upto any pitch in horizontal / vertical or
curved surface excluding the cost of purlins, rafters
and trusses and including cutting to size and shape
whereever required .( Prior Approval of S.E. is
essential)
Spec. No.: As directed by Engineer in charge.
86
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
36 Providing & fixing self supported (proflex or
equivalant make) roofing system for Godown,
workshop, or similar storage structure, made up of
structural grade steel sheet of 914 mm. width,
mounted at site using mechanical press dies to the
desired curve and shape to form 605 mm wide
interlocking panels. For span ---------mtr having
arch rise as --------mtr and arch length upto 33.0
meter. The base material made up of imported
galvalume steel complying to ASTM AT92 having
base metal thickness 0.80 millimeter with alloy
coating AZ150 and paint coating of regular modified
polyester, top wat 25 micron and bottom coat 12
micron as per approved color, including fixing
hangers,clamps etc as may be necessary
including fixing skylight of 2 mm thick
polycarbonats sheet of size 0.60 x 2.10 m and turbo
ventillator of 0.60 m diameter to be installed at
every 10 m along the length of roof including
finishing , testing & cleaning etc complete. ( Prior
Approval of S.E. is essential)
Spec. No.: As directed by Engineer in charge.
87
Bd - R : Roofing & Ceiling
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
38 Providing and fixing PVC coloured Ridge tiles over R.Mt. 557.00 19.00
UPVC roofing where required having size 113cm x
41cm and height9.5 cm for ridge including
fastening with self drilling screw having washers
made of stainless steel etc complete.
Spec. No.: As directed by Engineer in charge.
39 Providing and fixing glass crete roof in reinforced No. 818.00 130.00
concrete member (0.05 x 0.75 meter) in size at 60
centimeter, center to center with 12 millimeter thick
wired glass having thickness of 6 millimeter,
including all accessories and required fixtures and
fastenings, fitting etc. complete. (excluding
reinforced cement concrete member)
Spec. No.: As directed by Engineer-in-charge
88
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
1 a Providing and fixing frame with / without ventilator
of size as specified with ......................... for doors
and windows including chamfering, rounding,
rebating, iron holdfast of size 300mm x 40mm x
5mm with oil painting, etc. complete.
Spec. No.: As directed by Engineer in charge.
89
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
4 Providing and fixing cold rolled steel hollow door No. 849.00 224.00
frame 105mm x 60mm for the following sizes
including hold fast hinges, tie members with red
oxide and gray paint etc. complete as per I.S.I.
specifications and code of practice prescribed
including anticorrosive treatment as directed by the
engineer.
Spec. No.: As directed by Engineer in charge.
5 Providing and fixing M-40 grade thick vibrated pull R.Mt. 658.00 221.00
cast or similar type concrete frame with chamber
conforming to I.S. 6524-1983 having 6 mm dia.
bars 3 Nos. And stirrups @250 mm c/c and fixing in
wall with 6 Nos of hold fast of 12 mm dia bars 500
mm long including primer and oil painting etc,
complete) frame size 60 mm x 100 mm .
Spec. No.: As directed by engineer-in-charge.
6 Providing and fixing M-40 grade thick vibrated pull R.Mt. 692.00 255.00
cast or similar type concrete frame with chamber
conforming to I.S. 6524-1983 having 6 mm dia bars
3 Nos. And strips @250 mm c/c and fixing in wall
with 6 Nos. of hold fast of 12 mm dia bars 500 mm
long including primer and oil painting etc, complete)
frame size 60 mm x 125 mm
Spec. No.: As directed by engineer-in-charge.
7 Providing and fixing factory made polyvinyl chloride Rmt 386.00 85.00
(PVC) Door Frame in plain colour of the size 50 x
47mmwith a wall thickness of 5mm, made out of
extruded 5mm PVC sheet, mitre cut at two corners
and joined with 2nos. of 150mmlong brackets of
15mmx15mm M.S. square tube. The two vertical
door profiles are to be reinforced with 19mmx19mm
M.S. Square tube of 19 gauge, EPDM rubber
gasket weather seal to be provided through out the
frame. The door frame shall be fixed to the wall
90
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
using65/100mm long M.S. Screws through the
frame by using PVC fasteners. A minimum of 4nos.
of screws to be provided for each vertical member
& minimum 2nos. for horizontal member etc.
complete as per specification and direction of
Engineer-in-Charge
8 Providing and fixing factory made polyvinyl chloride Rmt 436.00 85.00
(PVC) Door Frame in Prelaminated colour of the
size 50 x 47mmwith a wall thickness of 5mm, made
out of extruded 5mm PVC sheet, miter cut at two
corners and joined with 2nos. of 150mmlong
brackets of 15mmx15mm M.S. square tube. The
two vertical door profiles are to be reinforced with
19mmx19mm M.S. Square tube of 19 gauges,
EPDM rubber gasket weather seal to be provided
through out the frame. The door frame shall be
fixed to the wall using65/100mm long M.S. Screws
through the frame by using PVC fasteners. A
minimum of 4nos. of screws to be provided for each
vertical member & minimum 2nos. for horizontal
member etc. complete as per specification and
direction of Engineer-in-Charge.
9 Providing and fixing Ghana teak wood single leaf Sq.Mt. 3829.00 765.00
second class fully paneled door shutter 35mm
thick with openable fan light as per detailed
drawings. excluding the door frame 60mm x
100mm stainless steel hinges and chromium plated
fixtures and fastening and finishing the wood work
with oil painting 3 coats.
91
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
10 Providing and fixing Ghana teak wood double leaf Sq.Mt. 4336.00 926.00
second class fully paneled door shutter 35mm
thick style and rail with 25 mm thick panels with
openable fan light as per detailed drawings.
excluding the door frame 60mm x 100mm stainless
steel hinges and cromium plated fixtures and
fastening and finishing the wood work with oil
painting 3 coats.
Spec. No.: Bd-T-7 & 8 Page No. 481-82
11 Providing and fixing ghana teak wood double leaf Sq.Mt. 3897.00 747.00
paneled door shutter without fanlight and 25mm
thick as per drawing consisting of Ghana T.W. top
rail size 100mm x 25mm and bottom and lock rail
200mm x 25mm insert pannel 12 mm thick
commercial ply faced T.W. particle board with
phenol formaldehyde synthetic resin (Generally
confirming to ISI 3097) excluding frame, including
stainless steel Hinges and cromium plated fixture
and fastening and T.W. beading to junctions of
paneled inserts and as instructed by the Engineer
in charge including 3 coats of oil painting etc.
complete.
Spec. No.: As directed by Engineer in charge.
12 Providing and fixing ghana teak wood double leaf Sq.Mt. 3260.00 574.00
paneled door shutter without fanlight and 25mm
thick as per drawing consisting of Ghana T.W. top
rail size 100mm x 25mm and bottom and lock rail
200mm x 25mm insert pannel 12 mm single side
veneer faced T.W. particle board with phenol
formaldehyde synthetic resin (Generally confirming
to ISI 3097) excluding frame, including stainless
steel Hinges and cromium plated fixture and
fastening and T.W. beading to junctions of paneled
inserts and as instructed by the Engineer in charge
including 3 coats of oil painting etc. complete.
Spec. No.: As directed by Engineer in charge.
92
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
13 Providing and fixing double leaf paneled door Sq.Mt. 3706.00 728.00
shutter without fanlight and shutter 35 mm thick as
per drawing consisting of Ghana T.W. top rail size
100mm x 35 mm and bottom and lock rail 200mm x
35mm insert panel 12 mm thick single side
decorative veneer faced T.W. particle board with
phenol formaldehyde synthetic resin (Generally
confirming to ISI 3097) excluding frame, including
stainless steel fixtures fastening and T.W. beading
at junction of panels inserts and as instructed by
the Engineer in charge including 3 coats of oil
painting etc. complete.
Spec. No.: As directed by Engineer in charge.
14 Providing and fixing double leaf paneled door Sq.Mt. 4200.00 966.00
shutter without fanlight and shutter 35 mm thick as
per drawing consisting of Ghana T.W. top rail size
100mm x 35 mm and bottom and lock rail 200mm x
35mm insert panel 12 mm thick single side
decorative veneer faced T.W. particle board with
phenol formaldehyde synthetic resin (Generally
confirming to ISI 3097) excluding frame, including
stainless steel fixtures fastening and T.W. beading
at junction of panels inserts and as instructed by
the Engineer in charge including 3 coats of oil
painting etc. complete.
15 Providing and fixing double leaf paneled door Sq.Mt. 3621.00 417.00
shutter excluding frame with glazed openable
fanlight shutter 35 mm thick as per detailed drawing
consisting Ghana.T.W. vertical styles 100 mm x 35
mm
93
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
and lock and bottom rail 200 mm x 35 mm and
panels 12 mm thick both side decorative veneer
commercial ply faced particle board including
stainless steel Hinges and cromium plated fixtures
and fastening and T.W. beading at junctions of
panel inserts and as instructed by the Engineer in
charge including 3 coats of oil painting etc.
complete.
Spec. No.: As directed by Engineer in charge.
16 Providing and fixing single leaf paneled door Sq.Mt. 4490.00 1266.00
shutter excluding frame with glazed openable
fanlight shutter 35 mm thick as per detailed
drawing consisting Ghana.T.W. vertical styles 100
mm x 35 mm and lock and bottom rail 200 mm x 35
mm and panels 12 mm thick both side decorative
veneer particle board including stainless steel
Hinges and chromium plated fixtures and fastening
and T.W. beading at junctions of panel inserts and
as instructed by the Engineer in charge including 3
coats of oil painting etc. complete.
Spec. No.: As directed by Engineer in charge.
17 Providing and fixing Ghana teak wood double leaf Sq.Mt. 4530.00 975.00
paneled shutters, 35 mm thick style and rail and 25
mm thick panels without ventilator as per detailed
drawing excluding the door frame, stainless steel
Hinges and cromium plated fixtures and fastening
and finishing the wood work with oil painting 3
coats complete.
Spec. No.: Bd-T-11 & 12, Page No. 482
18 Providing and fixing Ghana teak wood single leaf Sq.Mt. 3624.00 738.00
paneled shutters, 35 mm thick style and rail and 25
mm thick panels without ventilator as per detailed
drawing excluding the door frame, stainless steel
Hinges and chromium plated fixtures and fastening
and finishing the wood work with oil painting 3
coats complete.
Spec. No.: Bd-T-11 & 12, Page No. 482
94
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
19 Providing and fixing Ghana teak wood single leaf Sq.Mt. 3100.00 400.00
door shutter with teak wood style and rail of 25 mm
thick including fixing 50 mm x 25 mm size welded
mesh of 10 gauge as per detailed drawing or as
directed with stainless steel Hinges and cromium
plated fixture and fastening finishing with 3 coats of
oil painting etc. complete.
Spec. No.: Bd-T-39, Page No. 500
20 Providing and fixing factory made paneled door Sq.Mt. 2436.00 241.00
shutter in single leaf 35 mm thick style and rail
without ventilator with Ghana T.W. panels 12 mm
thick including wrought iron hold fast and stainless
steel Hinges and cromium platedfixtures with oil
painting 3 coats etc. complete.
Spec. No.: As directed by Engineer in charge.
21 Providing and fixing Ghana teak wood single leaf Sq.Mt. 2735.00 415.00
paneled door shutters 35 mm thick style and rail
and 19 mm thick Ghana T.W. panels as per
detailed drawing including wrought iron hold fast
stainless steel Hinges and cromium plated fixtures
and fastening and three coats of oil painting etc.
complete.
Spec. No.: As directed by Engineer in charge.
22 Providing and fixing C.C.T.W. double leaf shutter Sq.Mt. 4380.00 919.00
for second class partly paneled partly glazed door
without ventilator adopting sections and sizes as
given in the standard specifications Volume II
(1981) or as per detailed drawing, including Iron
oxidized fixtures / alluminium with powder coating
fixtures and fastenings and finishing the wood work
with one coat of primer etc. complete. (Without
frame)
Spec. No.: BdT- 11 Page No. 496
95
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
23 Providing and fixing C.C.T.W. single leaf shutter Sq.Mt. 3867.00 892.00
for second class partly paneled partly glazed door
without ventilator adopting sections and sizes as
given in the standard specifications Volume II
(1981) or as per detailed drawing, including Iron
oxidized/ alluminium with powder coating fixtures
fixtures and fastenings and finishing the wood work
with one coat of primer etc. complete. (Without
frame)
Spec. No.: BdT- 12 Page No. 496
24 Providing and fixing C.C.T.W. single swing Sq.Mt. 3073.00 647.00
shutter part size paneled as per detailed drawings,
including double acting brass spring hinges and
finishing with French polishing etc. complete.
(Without frame)
Spec. No.: BdT- 27 Page No. 501
25 Providing and fixing 25 mm thick C.C.T.W. single Sq.Mt. 2968.00 551.00
swing shutter part size paneled with obscured
glass as per detailed drawings or as approved,
including double acting brass spring hinges and
finishing with French polishing etc. complete.
(Without frame)
Spec. No.: BdT- 28 Page No. 502
26 Providing and fixing solid core flush door shutter Sq.Mt. 2775.00 409.00
in single leaf 30 mm thick decorative type of
exterior grade as per detailed drawings approved
face veneers 3 mm thick on both faces or as
directed, all necessary beads, mouldings and
lipping, wrought iron hold fasts, chromium plated
fixtures and fastenings, with brass mortise lock,
chromium plated handles on both sides, and
finishing with French Polish etc. complete.
Spec. No.: Bd-T-34, Page No. 503
96
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
27 Providing and fixing solid core flush door shutter Sq.Mt. 2570.00 471.00
commercial in single leaf 30 mm thick without
ventilator commercial type of exterior grade as per
detailed drawings with wrought iron hold fast,
stainless steel Hinges and cromium plated fixtures
and fastenings and handles on both sides and
finishing with oil painting 3 coats complete.
Spec. No.: Bd-T-36, Page No. 505
28 Providing and fixing solid core flush door Sq.Mt. 2250.00 310.00
commercial type on single leaf 16 mm thick Bison
Panel cement bonded particle Board including
Teak wood lipping beading on all four edges
without ventilator commercial type of exterior grade
as per detailed drawings with wrought iron hold
fast,stainless steel Hinges and cromium plated
fixtures and fastenings and handles on both sides
and finishing with oil painting three coats complete.
Spec. No.: As directed by Engineer in charge.
97
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
Engineer in charge and manufacturers specification
and drawing etc. complete.
Spec. No.: As directed by Engineer in charge.
32 Providing & Fixing 32 mm thick One piece single Sq.Mt. 2682.00 571.00
moulded puff ABSTRONE BUTADYNE STYRINE
(ABS) Door shutter for internal use including
toilets made up of outer ABS sheet of 1.2 mm thick
having puff insulation of 35 to 40 Kg/Cum.density
and 10 mm dia.for steel bars 2 Nos., wooden block
to receive fixtures, having M.S. hinges 100 mm
length, M.S. handles 150 mm length and 10 mm
dia sliding door bolt etc. complete.
Spec. No.: As directed by Engineer Incharge
98
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
33 Providing and fixing in position, Double shuttered Sq.Mt. 15460.00 4087.00
aluminium extruded powder coated openable door
of specified size with aluminium door frame of
powder coated section 101.60 x 44.75mm , 3.18
mm thick and shutter comprising of powder coated
section having bottom and lock rail of size 150 mm
x 44.5 mm , 2.90 mm thick top rails 47.62 x 44.45
mm , 3.18 mm thick , vertical style 47.62 x 44.45
mm, 3.00 mm thick and for shutter plain glass
panes 5 mm thick for top panels and 12mm thick
both side laminated phenol bonded particle board
panels for bottom panels etc. , I.S.I. mark , heavy
duty, Hydraulic floor spring of 150 kg capacity ,
having heavy duty concealed lock, necessary
beading, glazing clips, PVC gaskets, 250mm length
tower bolts, 150mm diam. pad handle, etc. as per
detailed design and drawing or as directed by
engineer in charge including all materials , labours,
and equipment etc.
Spec. No.: As directed by Engineer in charge.
99
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
150mm diam. pad handle, etc. as per detailed
design and drawing or as directed by engineer in
charge including all materials , labours, and
equipment etc
Spec. No.: As directed by Engineer in charge.
35 Providing and fixing 29 mm thick factory made Sq.Mt. 3957.00 436.00
PVC rigid foam paneled door shutters by approved
manufacturer and brand by from MS tube of 19
gauge thickness size 19 mm x 19mm for styles and
15 mm x 15 mm for top and bottom rails, covered
with heat moulded PVC C channel of 5 mm thick
and 75 mm wide PVC sheet for top rail, lock rail
and bottom rail on either side and 5 mm thick, 20
mm wide cross PVC sheet as gap insert for top rail
and bottom rail paneling of 5 mm thick PVC sheet
fitted in the M.S frame welded/sealed to the styles
and rails with 5mm x 30 mm PVC sheet beading on
either side and joined together with solvent cement
adhesive etc. complete as per manufacturers
specification and direction of Engineer in charge
fixed to the frames with stainless steel hinges of
125 mm size, and cromium plated fixtures including
all material, labour, machinery etc. complete ( for
WC, bath shutter) ( The item is exclusive of door
frame)
Spec. No.: As directed by Engineer in charge.
100
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
“Rajshri” PVC ‘C’ channel of size 30 x 100mm
forming stiles, and 5mm thick, 125mm wide PVC
sheets for top rail, lock rail & bottom rail on either
side, and 15mm (5mm x 3) thick, 20mm wide cross
PVC sheet as gap insert for top rail & bottom rail.
Paneling of 10 mm thick prelam PVC sheet to be
fitted in the M.S. frame welded / sealed to the stiles
& rails with 30mm wide x 5mm thick PVC sheet
beading on either side, and joined together with
solvent cement adhesive etc. An additional 5mm
thick PVC strip of 20mm width is to be stuck on the
interior side of the ‘C’ Channel using PVC solvent
cement adhesive. including stainless steel fixtures
and fastening Complete as per direction of
Engineer-in-charge, manufacturer’s specification &
drawing.
Spec. No.: As Directed By Engineer Incharge
101
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
38 Providing and fixing fiber glass reinforced polyster Sq.Mt. 3111.00 351.00
door shutter 30 mm thick as per IS 14856 (2000)
(Reaffirmed 2006) without ventilator including
chromium plated fixtures and fastening with
chromium plated handles on both sides, etc
complete.
Spec. No.: As directed by engineer-in-charge.
39 Providing and fixing fiber glass reinforced polyster Sq.Mt. 4114.00 454.00
door shutter 35 mm thick as per IS 14856 (2000)
(Reaffirmed 2006) without ventilator including
chromium plated fixtures and fastening with
chromium plated handles on both sides, etc
complete.
Spec. No.: As directed by engineer-in-charge.
40 Providing and fixing rolling shutter fabricated from
steel laths of minimum thickness 0.9 mm with lock
plate of 3.15 mm thickness reinforced with 35 x 35
x 5 mm angle section fitted with sliding bolts and
handles for both sides, deep M.S. channel section
of depth and thickness not less than 65 mm and
3.15 mm respectively with hold fast arrangements,
M.S. Bracket plate 300 x 300 x 3.15 mm minimum
size and shape with square bar, suspension shaft
of minimum 32 mm diameter, hood cover of M.S.
sheet not less than 0.9 mm thickness and of any
size at top and safety devices including mechanical
gear operation arrangement consisting of worm
gear wheels and worms of high grade cast iron or
mild steel and one coat of red lead primer etc.
complete. (I.S. 6248-1979)
Spec. No.: Bd.T.55, Page No. 514
102
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
41 Providing and fixing collapsible steel gate in one / Sq.Mt. 2923.00 1108.00
two leaves with hot rolled vertical channels of 18 x
9 x 3 mm minimum size, crossings of M.S. flats of
size 18 x 5 mm T or E section for runner of
minimum 40 x 6 mm size for flange, M.S. flat for top
runner of minimum size 40 x 12 mm with roller
wheels confirming to grade F.G. 150 fitted with
snap headed rivets of minimum size 6 mm max.
spacing of vertical channels be 100 mm enclosed
gate position and clear space of 150 mm between
two sets of crossings with hold fasts, stoppers,
spaces, handles, locking arrangement and one coat
of red lead primer & oil painting etc. complete. (I.S.
10521-1983).
Spec. No.: Bd.T.57, Page No. 515
42 Providing and fixing steel frame door of angle 50 x Sq.Mt. 971.00 383.00
50 x 6 mm mild steel bars with 16 mm dia.
horizontally at 10mm c/c for ventilator portion
including iron hold fast boxes for fixing shutters
including welding, finishing, painting etc. complete.
Spec. No.: As directed by Engineer in charge.
43 Providing and fixing steel frame door of angle 40 x Sq.Mt. 881.00 348.00
40 x 5 mm with 16 mm dia. mild steel bars
horizontally at 10cm c/c for ventilator portion
including iron hold fast for the fixing shutters
including welding, painting, finishing etc. complete.
Spec. No.: As directed by Engineer in charge.
103
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
45 Providing and fixing M.S. grill door 24 kg/sqm of Sq.Mt. 2212.00 975.00
various size as per detailed drawings without hot
dip coating, iron fixtures and fastenings and 3 coats
of oil painting etc.
Spec. No.: As directed by Engineer in charge.
46 Providing and fixing the Ghana teak wood second Sq.Mt. 2015.00 712.00
class fully glazed openable fanlight rectangular in
shape as per detailed drawing including the
frame,stainless steel Hinges and cromium plated
fixtures and fastenings and finishing the wood work
with 3 coats of oil painting.
Spec. No.: Bd-T-4 Page No. 492
47 Providing and fixing steel ventilator fully glazed Sq.Mt. 2216.00 447.00
partly fixed as per detailed drawing without hot dip
zinc coating including fabricating glazing with plain /
obscured glass panes and approved type and
quality and iron oxidized fixtures and fastening oil
paint 2 coats etc. complete.
Spec. No.: Bd. T. 53, Page No. 509 & As directed
by Engineer in charge.
48 Providing and fixing steel ventilator fully glazed Sq.Mt. 3050.00 841.00
partly fixed as per detailed drawing with hot dip
zinc coating including fabricating glazing with plain /
obscured glass pans and approved type quality and
iron oxidized fixtures and fastening with guard bars
12 mm square 10 cm c/c and oil painting 2 coats
etc. complete.
Spec. No.: Bd. T. 53, Page No. 509 and As directed
by Engineer in charge.
104
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
49 Providing and fixing in position powder coated Sq.Mt. 2757.00 342.00
aluminium louvered windows / ventilator of
various sizes with powder coating as per detailed
drawing and specifications including aluminium
frames 80 x 38 mm x 1.22 mm box type, 5 mm thick
sheet glass louvers, of approved quality etc.
complete.
Spec. No.: As directed by Engineer in charge.
50 Providing and fixing in position Mild steel fixed Sq.Mt. 1925.00 934.00
staggered ( Z Type )Ventilator as per detailed
drawing with hot deep zink coating including
fabricating with Mild steel 'Z 'Section of size 20mm
x 25 mm and 3 mm thick at weight 1.42
Kg/Rmt,with stainless steel mosquito net of 304
Grade,4 mm thick float glass as directed by
Engineer In charge including necessary welding
,grinding, two coats of oil paint etc.complete.
Spec. No.: As directed by Engineer Incharge
51 Providing and fixing in position anodised (as per IS Sq.Mt. 2992.00 680.00
1868/1982) Aluminium fixed staggered ( Z Type
)Ventilator with aluminium rectangular pipe 63 mm
x 38.10 mm x 1.22 mm at weight 0.650 Kg/Rmt,
Aluminium angle of size 15 mm x 15 mm x 1
mm,aluminium channel of 9 mm sizes,
S.S.mosquito net of 304 Grade,4 mm thick float
glass per detailed drawing & as directed by
Engineer in charge etc.complete.
Spec. No.: As directed by Engineer Incharge
105
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
53 Providing and fixing fully glazed double leaf Sq.Mt. 2390.00 503.00
window shutter with openable fanlight including
Ghana teak wood 25 mm thick style and rails with
plain / obscured glass panels as per drawing or as
directed by the Engineer in charge with stainless
steel hinges and cromium plated fixtures and
fastening and finishing the wood work with oil
painting three coats etc. complete.
Spec. No.: Bd-T-42, Page No. 507
54 Providing and fixing Ghana Teak Wood window Sq.Mt. 2771.00 617.00
with double leaf half glazed and half paneled
shutter with ventilator including wrought iron hold
fast, stainless steel hinges and cromium plated
fixtures and fastenings and finishing the wood work
with oil painting 3 coats etc. complete.
Spec. No.: Bd-T-42, Page No. 507
55 Providing and fixing Ghana teak wood windows Sq.Mt. 3441.00 457.00
with double leaf 25 mm thick planked shutters
without ventilators as per detailed drawings
including stainless steel hinges and cromium
plated fixtures and fastenings and finishing the
wood work with oil painting 3 coats etc. complete.
Spec. No.: Bd-T-43, Page No. 507
56 Providing and fixing ghana teak wood windows / Sq.Mt. 3945.00 502.00
ventilators with double leaf paneled shutters 25
mm thick without ventilators as per detailed
drawing including stainless steel hinges and
cromium plated fixtures and fastenings and
finishing the wood work with oil painting 3 coats etc.
complete.
Spec. No.: Bd-T-43, Page No. 507
106
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
57 Providing and fixing steel window of various sizes Sq.Mt. 2912.00 706.00
as per detailed drawing without hot dip zinc coating,
without ventilators, including fabricating / glazing
with plain / obscured glass panels of approved type
and quality, iron oxidised fixtures and fastenings, oil
painting two coats complete.
Spec. No.: Bd-T-53, Page No. 512
58 Providing and fixing steel window of various sizes Sq.Mt. 3263.00 547.00
as per detailed drawing without hot dip zinc coating,
without ventilators, including fabricating / glazing
with plain / obscured glass panels of approved type
and quality, iron oxidised fixtures and fastenings,
finishing with oil painting two coats complete (with
guard bars 12 mm square at 10 cm c/c.)
Spec. No.: Bd-T-53, Page No. 512
59 Providing and fixing steel window C.R.C. sheet as Sq.Mt. 2520.00 790.00
per I.S. 1513 : 1986. gauge sect. 65 x 40 x 25 mm
shutter single sheet of 24 gauge single leaf joined
by fusion welding at appropriate points with vertical
grooves of 15 mm wide and 15 mm deep at a
distance of 45 mm. The first and last rib should be
60 mm away from vertical edge of the shutter. the
shutter shall be welded, with angle to from the
periphery of the shutter. At the center of the frame
there shall be angle welded to bifurcate the frame
into segments with two leaf shutter square 12 mm
square guard bars at 120 mm center with all
accessories
Spec. No.: As directed by Engineer in charge.
107
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
60 Providing and fixing in position alluminium
openable window of any size as per detailed
drawing and as directed by Engineer-in-charge with
all necessary alluminium sections including
necessary fixtures and fastening with 5 mm thick
clear float glass etc. complete.
Spec. No.: As directed by Engineer in charge.
108
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
63 Providing and fixing 50 mm x 50 mm Mild Steel Sq.Mt. 2470.00 675.00
square pipe framed steel windows of various sizes
as per details with welded square bars 12 mm at 10
cm center to center without hot dip zinc coating
without / with ventilator including fabrication,
glazing with plain / obscured glass panes of
approved type and quality, all fixtures and
fastenings and finishing with one coat of primer
complete.
Spec. No.: As directed by Engineer in charge.
109
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
ii) without box frame. Sq.Mt. 3523.00 836.00
110
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
66 Supplying and fixing in position anodized intruded
modular aluminium section of
JINDAL/HINDALCO/OEL OR ANY OTHER
approved manufacturer confirming to IS
specification four track sliding windows moulded
on rectangular frameof size 127 x 45 x 3.18 mm
thick (2.834kg per rmt.) made up of four track
bottom section of size 122 x 45 x 1.3 mm thick
(1.829 kg/rmt) and top side section up size 122 x 31
x 1.1 mm thick (1.205 kg /rmt) The shutter should
be of bearing bottom of size 40 x 18 x 1.2 mm thick
(0.417 kg per / rmt) top member of size 40 x 18 x
1.2 mm thick (0.475 kg / rmt). Inter locking section
size 43 x 27 x 1.3 mm thick (0.558 kg /rmt) and
handle section of size 43 x 18 x 1.3 mm thick
(0.424 kg / rmt ) selected Quantity 5.5 mm thick
clear glass to be fixed shutter with neoprene gasket
with approved quality PVC rolers necessary locks
handle PVC liner and wooden encasement
wherever necessary etc. complete.
Spec. No.: As directed by Engineer-in-charge
111
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
68 Providing and fixing 16 mm dia. mild steel round Sq.Mt. 1256.00 304.00
bars at 100 mm c/c to windows / ventilators /
fanlights, fixing mild steel flats 40 x 6 mm in frame,
cutting a recess to fit the flat exactly, including
drilling the holes to flats to pass the bars through it
25 mm inside in wooden frame including providing
two central flats of 40 x 6 mm by drilling holes.
etc. complete.
Spec. No.: As directed by Engineer-in-charge
69 Providing and fixing 16 mm dia. mild steel round Sq.Mt. 1455.00 418.00
bars at 100 mm c/c to windows / ventilators /
fanlights, fixing mild steel flats 40 x 6 mm in frame,
cutting a recess to fit the flat exactly, including
drilling the holes to flats to pass the bars through it
25 mm inside in wooden frame including providing
one central flats of 40 x 6 mm by drilling holes
including one coat of primer etc. complete. (when
bar length exceeds 45 cm and upto 75 cm)
Spec. No.: As directed by Engineer-in-charge
70 Providing and fixing 16 mm dia. mild steel round Sq.Mt. 1651.00 517.00
bars at 100 mm c/c to windows/ventilators/fanlights,
fixing mild steel flats 40 x 6 mm in frame, cutting a
recess to fit the flat exactly, including drilling the
holes to flats to pass the bars through it 25 mm
inside in wooden frame without central mild steel
flats including providing one coat of primer etc.
complete. (No central flat to be provided upto 45 cm
bar length)
Spec. No.: As directed by Engineer-in-charge
71 Providing and fixing 16 mm dia.. mild steel bars to Sq.Mt. 912.00 348.00
window at 100 mm center to center, including one
coat of primer etc. complete. (without M.S. flats)
Spec. No.: As directed by Engineer-in-charge
112
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
72 Providing and fixing partition of welded mesh of 3 Sq.Mt. 1521.00 515.00
mm dia. wires 50 mm x 25 mm size mesh including
integrated non teak seasoned wood frame 80 x 50
mm of vertical and horizontal scantling and finishing
with oil painting 3 coats etc. complete.
Spec. No.: Bd-T-62, Page No. 517
113
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
76 Providing and fixing in position . extruded Sq.Mt. 2990.00 795.00
aluminium partitions having frame made out of
extruded tubular section of size 65 mm x 40 mm
with 12 mm thick three layered flat pressed teak
wood particle board bonded with BWP type
exterior grade phenol formaldehyde synthetic resin
conforming to IS 12923-1990, laminated on both
sides, Novateak or equivalent with aluminium
glazing clips of size 12 mm x 12 mm (conical) as
per drawing etc. complete.
Spec. No.: As directed by Engineer in charge.
77 Providing and fixing partitions using 1.84 m height Sq.Mt. 1344.00 248.00
and 12 mm thick teakwood particle board bonded
with phenol formal dehyde synthetic resin including
C.C.T.W. vertical 70 x 70 mm and top and bottom
rail of 70 x 35 mm and covering batten of 30 x 10
mm at 1.22 metre apart on both ways or as directed
including finishing with one coat of primer etc.
complete.
Spec. No.: As directed by Engineer-in-charge
78 Providing and fixing partitions using 1.84 m height Sq.Mt. 1488.00 148.00
and 12 mm thick teakwood one face particle and
other teak veneer bonded with phenol
formaldehyde synthetic resin including CTW vertical
70 x 70 mm and top and bottom rail of 70 x 35 mm
and covering batten of 30 x 10 mm at 1.22 metre
apart on both ways or as directed including
finishing with one coat of primer etc. complete.
Spec. No.: BdT- 63 Page No. 518
114
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
79 Providing and fixing partition using 1.84 metre Sq.Mt. 1584.00 351.00
height and 12mm thick teak wood with both faces
teak veneer bonded with phenol formaldehyde
synthetic resin including C.C.T.W. vertical 70 x 70
mm and top and bottom rail of 70 x 35 mm and
covering batten of 30 x 10 mm at 1.22 metre apart
on both ways or as directed including finishing with
one coat of primer etc. complete.
Spec. No.: As directed by Engineer-in-charge
80 Providing and fixing partition using 1.84m height Sq.Mt. 1280.00 109.00
and 12mm thick Plain particle board bonded with
phenol formaldehyde synthetic resin confirmed to
IS 3087-1985, including CTW vertical 70 x 70 mm
and top and bottom rail of 70 x 35 mm and covering
batten of 30 x 10 mm at 1.2m apart on both ways
or as directed including finishing with one coat of
prime coat etc.complete. (Excluding fixtures &
fastening)
Spec. No.: As directed by Engineer-in-charge
81 Providing and fixing partition using 1.84m height Sq.Mt. 1684.00 124.00
and 12mm thick Prelaminated particle board (IS
12823-1990)(OSL)one side decor lamination and
other side balancing white paper bonded with
phenol formaldehyde synthetic resin confirmed to
IS 3087-1985, including C.C.T.W vertical 70 x 70
mm and top and bottom rail of 70 x 35 mm and
covering batten of 30 x 10 mm at 1.2m apart on
both ways or as directed including finishing with
one coat of prime coat etc. complete. (Excluding
fixtures & fastening)
Spec. No.: As directed by Engineer-in-charge
115
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
82 Providing and fixing partition using 1.84m height Sq.Mt. 1830.00 135.00
and 12mm thick Prelaminated particle board (IS
12823-1990)(BSL) both side decor lamination
and bonded with phenol formaldehyde synthetic
resin confirmed to IS 3087-1985 including CTW
vertical 70 x 70 mm and top and bottom rail of 70 x
35 mm and covering batten of 30 x 10 mm at 1.2m
apart on both ways or as directed including
finishing with one coat of prime coat etc. complete.
(Excluding fixtures & fastening)
Spec. No.: As directed by Engineer-in-charge
83 Providing and fixing sheet glass of 24 oz. for all Sq.Mt. 583.00 175.00
size including putty etc. complete.
Spec. No.: Bd.S . Page No. 465 to 467
Spec. No.: As directed by Engineer-in-charge
85 Providing and fixing fly proof mesh shutter to Sq.Mt. 2230.00 342.00
ventilator/window using CCTW members of size 45
x 22 mm for frame work and 35 x 22 mm for middle
support and fixing fly proof mesh on it and covering
CCTW battens of size 20 x 10 mm including
priming and two coats of oil painting to the new
wood and steel work and all labour charges
including all fixture and fastenings etc. complete.
Spec. No.: As directed by Engineer in charge.
116
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
86 Providing and fixing aluminium grill diamond mesh Sq.Mt. 3764.00 682.00
type DG-202 of 7.5 mm thick including fixing in
position anodised aluminium frame section of 80 x
38 mm x 1.22 mm size box, cutting to the required
size with all wastage , labour, lead lift etc. complete.
Spec. No.: As directed by Engineer in charge.
117
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
91 Providing and fixing 4 mm thick plain A.C.. sheets Sq.Mt. 326.00 105.00
(of IS std.) on top of the weather shed including
scaffolding, fixing by means of nuts and bolts or as
directed etc. complete as per detailed drawing
(Brackets of 70 x 45 mm to be paid separately).
Spec. No.: As directed by Engineer-in-charge
118
Bd - T : Doors and Windows
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
98 Providing and fixing Acrylic plastic sheet (of IS
std.) panels of approved quality in required
thickness ...... mm plain, clear or any colour or
obscured linings in lieu of glass panels to
doors/windows including providing and fixing clips,
putty etc. complete. (with the prior permission of
S.E.) Spec. No.: As directed by Engineer-in-charge
119
Bd - U : Iron Work
Final Rate (2015-16)
ITEM
Description Unit Completed Labour
NO.
1 2 3 4 5
1 Providing and fixing mild steel grill work for
windows, ventilators etc. ----------- as per drawing
including fixtures, necessary welding & painting with
one coats of anticorrosive paint & two coats of oil
painting complete.
Spec. No.: Bd.U.1 Page No. 537
a 15 kg/sq.m Sq.Mt. 1129.00 181.00
b 20 kg./sq.m. Sq.Mt. 1414.00 184.00
2 Add for extra weight or deduct for less weight per Sq.Mt. 58.00 5.00
kg. for fabricating such as cutting, shaping, rivetting
etc. mild steel for grill works including welding etc.
complete.
120
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
1 Providing and laying cast iron pipes of B class
of ------ diameter with sockets and spigot ends/
flanges and cast centrifugally/ vertically including
specials, laying pipes and back filling the trench
complete including excavation.
Spec. No.: Bd.V.1 Page No. 593
a 80mm R.Mt. 852.00 37.00
b 100mm R.Mt. 1118.00 49.00
c 150mm R.Mt. 1528.00 46.00
2 Providing and making lead joints for ----------
diameter cast iron pipe line including lead and
testing.
Spec. No.: Bd.V.2 Page No. 595
a 80mm R.Mt. 345.00 114.00
b 100mm R.Mt. 429.00 133.00
c 150mm R.Mt. 489.00 134.00
3 Providing and making flanged connection for
the ------ diameter cast iron pipe line including
painting rubber insertion, nuts and bolts etc.
complete.
Spec. No.: Bd.V.3 Page No. 596
a 80mm R.Mt. 91.00 49.00
b 100mm R.Mt. 96.00 55.00
c 150mm R.Mt. 133.00 73.00
4 Providing and making ISI Mark ferrule
connection of ------------- dia. To water main
including ferrule coupling cast iron bell mouth
cover, built in non return valve and fixing
including excavation and reinstatement complete.
Spec. No.: Bd.V. 4 page 597
a 15 mm No. 745.00 267.00
b 20 mm No. 892.00 293.00
c 25 mm No. 1492.00 393.00
d 32 mm No. 1995.00 295.00
e 40 mm No. 3207.00 295.00
f 50 mm No. 4504.00 295.00
121
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
5 Providing and laying in trenches ----------
dia........... grade Galvanised iron pipes having
embossed I.S.I. mark on it, of jindal/Tata/Zenith
or equivalant make of .......... kg/metre necessary
fitting remaking good the demolished portion with
filling trenches and with primer of anti-corrosive
oil paint , 2 coats complete.
Spec. No.: Bd.V.5 Page No. 596
A HEAVY (Class 'C' )
a 15 mm, (1.504 kg per RMT) R.Mt. 257.00 75.00
b 20 mm, (1.953 kg per RMT) R.Mt. 355.00 75.00
c 25 mm, (3.058 kg per RMT) R.Mt. 399.00 80.00
d 32 mm, (3.927 kg per RMT) R.Mt. 488.00 80.00
e 40 mm, (4.545 kg per RMT) R.Mt. 568.00 85.00
f 50 mm, (6.329 kg per RMT) R.Mt. 735.00 85.00
g 80 mm, (10.309 kg per RMT) R.Mt. 1128.00 105.00
h 100 mm, (15.152 kg per RMT) R.Mt. 1524.00 110.00
B MEDIUM (Class 'B' )
a 15 mm Dia., (1.27 kg per RMT) R.Mt. 236.00 70.00
b 20 mm Dia., (1.64 kg per RMT) R.Mt. 302.00 70.00
c 25 mm Dia., (2.52 kg per RMT) R.Mt. 361.00 76.00
d 32 mm Dia., (3.24 kg per RMT) R.Mt. 437.00 76.00
e 40 mm Dia., (3.73kg per RMT) R.Mt. 500.00 81.00
f 50 mm Dia., (5.23 kg per RMT) R.Mt. 630.00 81.00
g 80 mm Dia., (8.27 kg per RMT) R.Mt. 984.00 99.00
h 100 mm Dia., (17.21 kg per RMT) R.Mt. 1411.00 109.00
6 Providing & fixing on walls/ ceiling/ floors,
...........mm dia.Galvanised heavy grade iron
pipes having embossed I.S.I. mark on it, of
jindal/Tata/Zenith or equivalant make of required
diameter and weight .......kg/rmt with screwed
socket joints necessary galvanised iron fitting
such socked back nuts albows bends tees
reducer enlagers plugs clamps etc. including
removing good to the demolished portion primer
of anticorrossive paint in two coats complete.
Spec. No.: Bd.V.5 Page No. 596
122
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
A HEAVY (Class 'C' )
a 15 mm, (1.504 kg per RMT) R.Mt. 264.00 74.00
b 20 mm, (1.953 kg per RMT) R.Mt. 370.00 85.00
c 25 mm, (3.058 kg per RMT) R.Mt. 417.00 92.00
d 32 mm, (3.927 kg per RMT) R.Mt. 521.00 106.00
e 40 mm, (4.545 kg per RMT) R.Mt. 630.00 135.00
f 50 mm, (6.329 kg per RMT) R.Mt. 829.00 164.00
g 80 mm, (10.309 kg per RMT) R.Mt. 1218.00 178.00
h 100 mm, (15.152 kg per RMT) R.Mt. 1689.00 205.00
B MEDIUM (Class 'B' )
a 15 mm Dia., (1.27 kg per RMT) R.Mt. 244.00 77.00
b 20 mm Dia., (1.64 kg per RMT) R.Mt. 317.00 84.00
c 25 mm Dia., (2.52 kg per RMT) R.Mt. 379.00 92.00
d 32 mm Dia., (3.24 kg per RMT) R.Mt. 471.00 105.00
e 40 mm Dia., (3.73kg per RMT) R.Mt. 561.00 135.00
f 50 mm Dia., (5.23 kg per RMT) R.Mt. 724.00 164.00
g 80 mm Dia., (8.27 kg per RMT) R.Mt. 1074.00 179.00
h 100 mm Dia., (17.21 kg per RMT) R.Mt. 1520.00 205.00
7 Providing and laying in trenches …... mm dia.
CPVC pipe of Prince / Sudhakar / Kishan /
Supreme or equivalent make including necessary
excavation, fittings. Refilling trenches etc.
complete.
Spec. No.: BD.V 5 page 596and as directed by
Engineer in charge
a 15 mm R.Mt. 167.00 69.00
b 20 mm R.Mt. 196.00 69.00
c 25 mm R.Mt. 247.00 75.00
d 32 mm R.Mt. 342.00 75.00
e 40 mm R.Mt. 392.00 79.00
f 50 mm R.Mt. 577.00 80.00
8 Providing and fixing on walls/ ceiling/ floor -------
dia. CPVC pipe of Prince / Sudhakar / Kishan /
Supreme or equivalent make with necessary
fittings, remaking good the demolished portion
etc. complete.
Spec. No.: BD.V 5 page 596 and as directed by
Engineer in charge
123
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
a 15 mm R.Mt. 174.00 75.00
b 20 mm R.Mt. 212.00 83.00
c 25 mm R.Mt. 264.00 90.00
d 32 mm R.Mt. 376.00 104.00
e 40 mm R.Mt. 453.00 133.00
f 50 mm R.Mt. 671.00 162.00
9 Providing & laying in walls ----- mm dia R.Mt.
heavy/medium having embosed as ISI mark of
jindal/Tata/Zenith or equivalant make galvanise
iron pipe ----- kg/Rmt necessary fitting for
concealed pipe work including cutting chase &
making good the wall etc complete (GI pipe
Heavy) Spec. No.: As directed by Engineer-in-
charge
A HEAVY (Class 'C' )
i 15 mm, (1.504 kg per RMT) R.Mt. 361.00 143.00
ii 20 mm, (1.953 kg per RMT) R.Mt. 459.00 143.00
iii 25 mm, (3.058 kg per RMT) R.Mt. 497.00 143.00
iv 32 mm, (3.927 kg per RMT) R.Mt. 586.00 143.00
v 40 mm, (4.545 kg per RMT) R.Mt. 661.00 143.00
B MEDIUM (Class 'B' )
i 15 mm Dia., (1.27 kg per RMT) R.Mt. 341.00 143.00
ii 20 mm Dia., (1.64 kg per RMT) R.Mt. 406.00 143.00
iii 25 mm Dia., (2.52 kg per RMT) R.Mt. 459.00 143.00
iv 32 mm Dia., (3.24 kg per RMT) R.Mt. 535.00 143.00
v 40 mm Dia., (3.73kg per RMT) R.Mt. 592.00 143.00
124
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
10 Providing and fixing chlorinated Polyvinyl chloride
(CPVC) pipes of Prince / Sudhakar / Kishan /
Supreme or equivalent make having thermal
stability for hot & cold water supply, including all
CPVC plain & brass threaded fitting I/C fixing the
pipe with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings, with one step
CPVC solvent cement and the cost of cutting
chases and making good the same including
testing of joints complete as per direction of
engineer in charge. Concealed work, including
chases and making good the wall etc. ---------
nominal outer dia pipes.
Spec. No.: As directed by Engineer in charge.
125
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
c 25 mm No. 382.00 39.00
13 Providing and fixing screw down -----------
diameter wheeled stop tap of brass including
necessary sockets/union nut complete.
Spec. No.: Bd.V.9 Page No. 601
a 15 mm No. 254.00 39.00
b 20 mm No. 321.00 43.00
c 25 mm No. 398.00 43.00
d 32 mm No. 619.00 54.00
e 40 mm No. 694.00 49.00
f 50 mm No. 749.00 50.00
g 65 mm No. 840.00 75.00
h 80 mm No. 895.00 65.00
14 Providing and fixing 100 mm dia. chromium No. 305.00 36.00
plated brass showers rose to 15mm dia. supply
pipe including necessary bend and socket
complete.
Spec. No.: Bd.V. 12 Page No. 603
15 Providing and fixing ----------- diameter
concussion push button type brass/gun metal
self-closing tap including necessary socket
complete.
Spec. No.: Bd.V.14 Page No. 604
a 15 mm No. 230.00 6.00
b 25 mm No. 256.00 52.00
16 Providing and fixing H.D.P container Sintex or Ltr. 10.00 0.00
equivalent make conforming to 15 spce. one
piece moulded water tank made out of high
density polythyler and built corrugated inclusive
of delivery up to destination hoisting and fixing of
accessories such as inlet,outlet overflow pipe
inclusive of all tanks capacity between 200 to
1000 liters
Spec. No.: As directed by engineer-in-charge.
126
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
17 Providing and fixing H.D.P container Sintex or Ltr. 9.00 0.00
equivalent make conforming to 15. one piece
moulded water tank made out of high density
polythyler and built corrugation including of
delivery up to destination hoisting and fixing of
accessories such as inlet, outlet overflow of all
tanks capacity above 1000 to 20,000 litres
Spec. No.: As directed by engineer-in-charge.
18 Providing and fixing 45 cm wide steel ladder of R.Mt. 791.00 443.00
40mm x 6 mm mild steel flat stringers and steps
of 18 mm dia. mild steel bar for water tank
including fixing it in (1:2:4) M-15 cement concrete
block 60cm x 30cm x 30cm & painting the ladder
complete.
Spec. No.: Bd. V. 19 Page No. 608
19 Providing and fixing Orissa type white glazed No. 2582.00 1261.00
earthenware 575 mm water closet pan of
Hindustan / Perryware / Neycer / Cera or
equivalant make including S trap with
earthenware foot rests, cast iron soil and vent
pipe upto outside face of the wall 1:2:4 brick bat
lime concrete bedding without flushing tank
and its accessories etc. complete.
Spec. No.: As directed by Engineer in charge.
20 Providing and fixing 1st class white glazed No. 6510.00 848.00
earthenware Orissa Type W.C. Pan of
Hindustan / Perryware / Neycer / Cera or
equivalant make 575 mm including P or S trap
cast iron soil and vent pipe upto the outside face
of the wall (1:5:1 0) cement concrete bedding 15
mm thick, 10 liter P.V.C. low level flushing
cistern with all necessary pipe connection etc.
complete.
Spec. No.: As directed by Engineer in charge.
127
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
21 Providing & fixing orissa type colour glazed No. 7874.00 1230.00
earthenware 625 x 450 mm. w.c. pan of
Hindustan / Perryware / Neycer / Cera or
equivalant make including trap, C.I. soil & vent
pipe upto the out side face of wall including 100
mm. dia. C.I. plug, bend, 15mm. thick 10 litre
PVC low level flushing cistern with all necessary
pipe connection etc. complete.
Spec. No.: As directed by Engineer in charge.
22 Providing and fixing European type white glazed No. 4996.00 1259.00
earthenware coupled closet of Hindustan /
Perryware / Neycer / Cera or equivalant
makesymphonic trap with symphonic low level
white glazed 10 litres cistern with black backlite
seat with all necessary pipe connection etc.
complete.
Spec. No.: As directed by Engineer in charge.
23 Providing and fixing European type wall-hung No. 7460.00 1253.00
white water closet of Hindustan / Perryware /
Neycer / Cera or equivalant make with push
valve concealed type with cover plate 32mm size
of JAQUAR MAKE SERIES FLV-1095 including
soil pipe ,vent pipe up to outside face of wall
,100mm dia. G.I. plug bend inlet pipe all fittings,
cutting& making good walls, floors etc. complete.
Spec. No.: As directed by Engineer Incharge
128
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
24 Providing and fixing European type -------
earthenware water closet pan of Hindustan /
Perryware / Neycer / Cera or equivalant make
with UPVC seat and lid with chromiumplated
brass hinges and rubber buffers including UPVC
and vent pipe up to the outside face of wall 10
literenameled low level flushing cistern with
fittings pipe stop tap brackets for fixing cistern 32
mm dia. UPVC flush pipe with fittings and clamps
,20 mm dia.UPVC overflow pipe ,mosquito proof
couplings G.I. chain and pulley,with water Jet
and fitting including cutting and making good to
the walls and floors testing etc. complete.( prior
approval of sample and brand by Ex. Engineer is
necessary before use)
Spec. No.: Specfications Bd v 21 page 610
a white glazed No. 4576.00 1200.00
b coloured glazed No. 4768.00 1145.00
25 Providing and fixing European type ------
earthenware water closet pan of Hindustan /
Perryware / Neycer / Cera or equivalant make
with UPVC seat and lid with chromium plated
brass hinges and rubber buffers including UPVC
and vent pipe up to the outside face of wall
without flushing cistern with flush cock and
with water Jet and necessary fittings including
cutting and making good to the walls and floors
testing etc. complete.( prior approval of sample
and brand by Ex. Engineer is necessary before
use)
Spec. No.: Specfications Bd v 21 page 611
a white glazed No. 3853.00 1198.00
b coloured glazed No. 4045.00 1182.00
129
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
26 Providing and fixing Anglo Indian type white No. 6385.00 1611.00
glazed earthenware water closet pan of
Hindustan / Perryware / Neycer / Cera or
equivalant make with trap with UPVC seat and lid
with chromium plated brass hinges and rubber
buffers including UPVC and vent pipe up to the
outside face of wall with flushing cistern and
necessary fittings including cutting and making
good to the walls and floors testing etc.
complete.( prior approval of sample and brand by
Ex. Engineer is necessary before use)
Spec. No.: Specfications Bd v 21 page 608
27 Providing and fixing high level 10 liter capacity No. 1306.00 184.00
with fittings inlet PVC pipe with stop tap ,brackets
for fixing the cistern,32 mm dia. PVC flush pipe
with fitting and clamps 20 mm dia. PVC overflow
pipe with mosquito proof couplings, galvanised
iron chain and pulley painting if ordered to cistern
pipe etc. and cutting and making good the
damaged wall and testing etc. complete ( Prior
approval of sample and brand by Ex. Engr. is
necessary before use)
Spec. No.: Specfications
130
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
29 Providing and fixing ------------ earthenware
lipped flat back/corner type Urinal of Hindustan /
Perryware / Neycer / Cera or equivalant make
with PVC 5 liters flushing system of 5 liters with
fittings, inlet pipe with stop tap, brackets for fixing
the cistern, 32 mm diameter P.V.C. flush pipe
with fitting including lead soil pipe, lead trap &
soil pipe connection up to the outside face of
wall.
Spec. No.: Bd.V.26 Page No. 564
a White Glazed No. 3087.00 503.00
b Coloured Glazed No. 3243.00 503.00
30 Providing and fixing White glazed earthenware No. 4370.00 1139.00
semi stall type urinals of Hindustan / Perryware
/ Neycer / Cera or equivalant make (of IS Std.)
without cistern, with inlet pipes stop tap,uUPVC
flush pipe with fittings and flushing arrangement
including uPVC soil pipe,uPVC trap and soil pipe
connection upto outside face of wall, making
good the damaged surface, testing etc. complete.
(Prior approval of sample and brand by
Ex.Engineer is necessary before use.)
Spec. No.: As directed by Engineer-in-charge
131
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
32 Providing and fixing Oval Type Under Counter R.Mt. 1303.00 168.00
Wash Hand Basin of 400 mm x 560 mm size
and of special colour shade having Telephonic
Black / Colour Granite of 180 mm thick fixed on
Black Kadappa Framework, including Chromium
Plated Coupling Bottle-Trap using Cera Company
or equivalent Oval Type Wash basin Model No
3448 as per detailed drawing or as directed by
Engineer-In- Charge etc. Complete
Spec. No.: As directed by Engineer Incharge
132
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
35 Providing and fixing --------- pedestal for Wash
Hand Basin of Hindustan / Perryware / Neycer /
Cera or equivalant make of approved size and
quality testing etc. complete. (Prior approval of
sample and brand by Ex. Engineer is necessary
before use.)( with permission of S.E.)
Spec. No.: As directed by Engineer-in-charge
133
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
39 Providing and fixing ------ rigid PVC Nahani trap
including PVC grating ,bend, connecting piece of
UPVC pipe up to the outside face of wall ,making
the good damaged surface and testing etc.
complete ( Prior approval of sample and brand by
Ex. Engr. is necessary before use)
Spec.
No.: Specfications Bd V 32 Page No. 615
a 8 cm No. 299.00 146.00
b 10 cm No. 316.00 185.00
c 15 cm No. 355.00 112.00
40 Providing and fixing P.V.C. Rain meter pipes of No. 511.00 116.00
110mm outer diameter and having wall thickness
of 2.2 to 2.7 mm confirming to I.S. 13592-1992
including proper rainwater receiving recess with
P.V.C. plug, bend, necessary fittings, such as,
offsets, shoes, inluding fixing the pipe on wall
using approved wooden cleats projecting 25mm
to 40mm from face of wall a fixing with clips of
approved quality and number ,filing the joint
using rubber gasket with solvent cement and
properly resting the shoe of pipes on C.C. or
masonry blocks, including necessary scaffolding
and maintenance for 3 yrs for any leakages or
dislocations of pipes. All the P.V.C. fittings and
additional 2 piece socket clips shall be got
approved from engineer in charge etc. complete.
(The contractor shall give 3 yrs guarantee bond
for payment)
Spec. No.: As directed by Engineer in charge
134
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
41 Providing and fixing ---------------- dia stabiliser
pipe / U.P.V.C. SWR soil vent/waste pipe of
Prince / Sudhakar / Kishan / Supreme or
equivalent make (conforring to 15 spal) and with
necessary fixtures and fitting such as bends,
tees, single junctions, slotted vent, clamps etc.
com-plete.
Spec. No.: As directed by Engineer in charge.
a 75 mm R.Mt. 371.00 101.00
b 110 mm R.Mt. 555.00 101.00
c 160 mm R.Mt. 1204.00 101.00
42 Providing , laying & fixing ,jointing Supreme Eco-
drain -------- SN 8 Nu- Drain Upvc pipes or of
equivalent make, manufacture as per EN 13476
or equivalent as per I.S.15328 with fittings such a
bends, tees, coupler, etc, jointing with rubber
lubricant including necessary excavation, trench
refilling with selective excavated material etc.
complete.
Spec. No.: As Directected By Engineer Incharge
135
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
b Providing and laying 100mm diameter half R.Mt. 243.00 7.00
round salt glazed stoneware pipes in brick
masonry including fittings such as bends, tees,
single junction, necessary excavation and jointing
complete.
Spec. No.: Bd.V.37, Page No. 622
45 Providing and laying -------- dia salt glazed
stoneware pipe including fittings such as bends,
tees, single junction, double junctions laying,
jointing (including excavation and refilling the
trenches) complete.
Spec. No.: Bd.V.39, Page No. 623
a 100 mm R.Mt. 190.00 47.00
b 150 mm R.Mt. 280.00 58.00
c 225 mm R.Mt. 352.00 62.00
46 Providing and laying concrete pipes of I.S.NP.
class of --------- diameter in proper line, level and
slope including necessary collars, excavation,
laying, fixing with collars in cement mortar 1:1
and refilling the trench complete.
Spec. No.: Bd.V.41, Page No. 625
a 100 mm R.Mt. 472.00 147.00
b 150 mm R.Mt. 482.00 138.00
c 225 mm R.Mt. 531.00 140.00
c 300 mm R.Mt. 760.00 148.00
47 Providing & constructing Brick Masonry
Inspection Chamber ....................... size
including 1:4:8 cement concrete foundation 1:2:4
cement concrete channels half round G.S.W.
pipes, Brick Masonry, plastering from inside and
airtight .............. cover with frame fixed in cement
concrete etc. complete.
Spec. No.: Bd.V.43, Page No. 626
A 60cm x 45cm x 90cm
i) C. I. lid No. 6003.00 935.00
ii) with R.C.C. Cover. No. 4505.00 707.00
B 90cm x 45cm x 90cm
136
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
i) C.I. lid cover No. 6821.00 1067.00
ii) with R.C.C. Cover. No. 5162.00 816.00
48 Providing and constructing Brick Masonry
Interseptic Chamber 90cm x 45cm including
1:4:8 C.C foundation, 1:2:4 C.C.channels/half
round glazed stoneware pipe channel, salt
glazed stone-ware intercepting trap with rodding
pipe set in 1:4:8 cement concrete block, brick
masonry plastering inside and Outside, with
............ cover with frame fixed in cement
concrete.
Spec. No.: Bd.V.44, Page No. 626
a C.I. lead No. 7422.00 1067.00
b with R.C.C. Cover. No. 6203.00 900.00
49 Providing , constructing & fixing Supreme make No. 2992.00 372.00
or equivalent make Ultra 250 mm dia.
Inspection chamber made up of uPVC material
of thickness 3.5 mm & height of 259 mm with
inlet & outlet of 110 mm dia. with 75 mm dia. U
Trap, Ultra shaft pipe of Upvc material having
height of 470 mm and fixing Ultra 250 mm dia.
uPVC cover & frame in 150 mm thick in
c.c.1:2:4, having crushed sand bed of 100 mm
thick of size 550 mm dia. Including excavation &
refilling the sides of chamber by crushed sand
cushioning 150 mm thickness, connecting all
required uPVC fittings with rubber lubricant etc.
complete.
Spec. No.: As Directected By Engineer Incharge
137
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
50 Providing , constructing & fixing Supreme make No. 8254.00 413.00
or equivalent make Ultra 450 mm dia.
Inspection chamber made up of
Polypropylene/polyethylene material of
thickness 3.5 mm & height of 388 mm with 160 or
200 mm main inlet (s) outlet & 110 & / or 160 mm
branch inlets, with 450 mm dia. Ultra shaft pipe of
HDPE material having height of 460 mm, having
R.C.C. cover & frame fixing in 150 mm thick in
c.c.1:2:4, having crushed sand bed of 150 mm
thick of size 750 mm dia. Including excavation &
refilling the sides of chamber by sand crushed
cushioning 150 mm thickness, connecting all
required uPVC fittings with rubber lubricant etc.
complete.
Spec. No.: As Directected By Engineer Incharge
138
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
52 Providing soak pit of size 120cm x 120cm x No. 895.00 288.00
120cm including excavating and filling with brick-
bats.
Spec. No.: Bd.V.46, Page No. 627
53 Providing and fixing reinforced cement
concrete cover of size 90 cm x 45 cm with frame
over inspection chamber etc. complete. Heavy
duty (225 kg)
Spec. No.: As directed by Engineer in charge.
A 90 cm x 45 cm
i) Heavy duty (225 kg) No. 2513.00 194.00
b Medium duty (140 kg) No. 1722.00 309.00
B 60 cm x 45 cm
i) Heavy duty (160 kg) No. 2318.00 299.00
ii) Medium duty (100 kg) No. 1332.00 286.00
54 Providing and fixing hume pipe septic tank No. 11205.00 1194.00
900mm diameter with vent pipe and cap
including necessary (including excavation and
laying)
Spec. No.: Bd.V.45, Page No. 627
55 Cleaning the Septic Tank upto 1.50 Cubic Meter Ltr. 2.00 2.00
capacity or equivalent etc. complete
Spec. No.: As directed by Engineer-in-charge
56 Providing and Fixing half turn 25 mm dia gun No. 352.00 46.00
metal flushing cock including all accessories
etc. complete.
Spec. No.: As directed by Engineer in charge.
57 Providing and fixing C.P. Angular stop cock No. 879.00 124.00
with wall flange jaquar make continental
(CAT.NO. CON-059) including necessary
sockets/union nut etc. complete.
Spec. No.: As directed by Engineer in charge
139
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
58 Providing and fixing C.P.Two way BIB cock No. 1070.00 113.00
jaquar make continental (CAT.NO. CON-041)
including necessary sockets/union nut etc.
complete.
Spec. No.: As directed by Engineer in charge
59 Providing and fixing C.P. wall mixer with No. 3696.00 257.00
provision for overhead shower with 115mm long
bend pipe & wall flange jaquar make continental
(CAT.NO. CON-273 UPR) including necessary
sockets/union nut etc. complete.
Spec. No.: As directed by Engineer in charge
60 Providing and fixing C.P. pillar cock long neck No. 1122.00 95.00
with aerator jaquar make continental (CAT.NO.
CON -021) including necessary sockets/union
nut etc. complete.
Spec. No.: As directed by Engineer in charge
61 Providing and fixing C.P. BIB cock with wall No. 866.00 133.00
flange jaquar make continental (CAT.NO. CON-
047) including necessary sockets/ union nut etc.
complete
Spec. No.: As directed by Engineer in charge
62 Providing and fixing C.P. sink cock with raised No. 1598.00 129.00
J shaped swinging casted spout jaquar make
continental (CAT.NO. CON -359) including
necessary sockets/ union nut etc. complete.
Spec. No.: As directed by Engineer in charge
63 Providing and fixing in position UPVC ultra violet No. 111.00 6.00
stabilized 110 mm outer diameter cowl dome
confirming to I.S.-4985 including making joints
with solvent cement etc. complete
Spec. No.: As directed by Engineer in charge
140
Bd - V : Water Supply and Sanitary Fittings
ITEM Final Rate (2015-16)
Description Unit Completed Labour
NO.
1 2 3 4 5
64 Providing and fixing fittings and accessories No. 2590.00 1477.00
such as ball cock, overflow pipe with mosquito
proof coupling, scour, pipe with plug, manhole
with cover and locking arrangement, connecting
pipes and embedding intake and outflow pipes
into the R.C.C water reservior etc. complete.
Spec. No.: BdV-18 Page No. -607
65 Providing and fixing --------- dia Ball cock
medium type with PVC float including sockets &
necessary fittings and tested as per municipal
requirements etc. complete.
Spec. No.: As directed by Engineer in charge.
a 15 mm. No. 201.00 32.00
b 40 mm. No. 587.00 13.00
66 Providing and fixing 450mm x 550mm size No. 637.00 59.00
superior type Belgium mirror with 16mm dia.
nickel plated towel rod etc. complete
Spec. No.: As directed by Engineer in charge.
67 Providing and fixing chromium plated towal rod No. 158.00 16.00
16 mm dia and 75 cm. in length including all
accessories complete.
Spec. No.: As directed by Engineer in charge.
68 Providing and fixing 5 to 6mm thick Glass for No. 551.00 64.00
shelf of size 125 mm x 600 mm with necessary
chromium plated brackets providingT.W.gutties
etc. complete
Spec. No.: As directed by Engineer in charge
141
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
1 Removing double country tiled roof with ridge and Sq.Mt. 49.00 48.00
battens and stacking the materials as directed with
all etc. and leads and lifts, complete including
removing wood work below.
Spec. No.: Bd.W.8 Page No. 716
2 Removing planking from roof or ceiling and stacking Sq.Mt. 22.00 21.00
them as directed with all leads and lifts completed.
Spec. No.: Bd.W.8 Page No. 716
3 Removing Queen Post truss from roof and stacking No. 731.00 717.00
the materials as directed with all leads and lifts
complete.
Spec. No.: Bd.W.8 Page No. 716
4 Removing King Post truss from roof and stacking No. 496.00 486.00
the materials as directed with all leads and lifts
complete.
Spec. No.: Bd.W.8 Page No. 716
5 Removing Other type below 5 metres span from roof No. 361.00 354.00
and stacking the materials as directed with all leads
and lifts complete.
Spec. No.: Bd.W.8 Page No. 716
6 Dismantling flat wooden or A.C. sheet ceiling with Sq.Mt. 24.00 24.00
frame work including stacking the materials as
directed with all leads, lifts, complete.
Spec. No.: Bd.W.8 Page No. 716
7 Removing cloth ceiling including frame work and Sq.Mt. 10.00 10.00
stacking the materials as directed with all leads, lifts,
complete.
Spec. No.: As directed by Engineer in charge.
8 Dismantling brick masonry in Mud and stacking the Cu.Mt. 111.00 109.00
materials as directed with all leads lifts, complete.
Spec. No.: As directed by Engineer in charge.
142
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
10 Dismantling stone masonry in mud including Cu.Mt. 114.00 112.00
stacking the materials as directed with all leads, lifts,
complete.
Spec. No.: As directed by Engineer in charge.
11 Dismantling stone masonry in lime or cement Cu.Mt. 162.00 159.00
including stacking the materials as directed with all
leads, lifts, complete.
Spec. No.: As directed by Engineer in charge.
12 Removing lime or lean cement concrete including Cu.Mt. 237.00 232.00
stacking the spoils as directed with all leads, lifts,
complete.
Spec. No.: As directed by Engineer in charge.
13 Removing rich mix cement concrete including Cu.Mt. 399.00 389.00
stacking the spoils as directed with all leads, lifts,
complete.
Spec. No.: As directed by Engineer in charge
14 Removing brick bat coba including stacking the Cu.Mt. 259.00 254.00
spoils as directed with all leads, lifts, complete.
Spec. No.: As directed by Engineer in charge.
15 Removing doors and windows with frames and No. 70.00 68.00
stacking the materials as directed with all leads, lifts,
complete.
Spec. No.: As directed by Engineer in charge.
16 Removing ventilators and small windows with frame No. 66.00 65.00
and stacking the materials with all leads lifts,
complete.
Spec. No.: As directed by Engineer in charge.
17 Removing wooden or A.C. partition including frame Sq.Mt. 36.00 35.00
work and stack-ing the materials as with all leads,
lifts, complete.
Spec. No.: As directed by Engineer in charge.
18 Removing teak wood trellies work with frame Sq.Mt. 19.00 19.00
including stacking the materials as directed with
frame including stacking the materials as directed
with all leads, lifts, complete.
Spec. No.: As directed by Engineer in charge.
143
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
19 Dismantling G.I. and A.C. sheet roof covering and Sq.Mt. 10.00 10.00
stacking them as and where directed in the
compound, including scaffolding etc. complete.
Spec. No.: BdW- 8 Page No. 716
20 Dismantling doors and windows shutters without No. 27.00 26.00
frame and stacking the materials as directed with all
leads, lifts etc. complete.
Spec. No.: BdW- 8 Page No. 716
21 Dismantling ventilators and small window shutters No. 72.00 70.00
without frame and stacking the materials with all
leads, lifts etc. complete.
Spec. No.: BdW- 8 Page No. 716
22 Dismantling trap stone from floor without bed Sq.Mt. 42.00 41.00
concrete including stacking the materials as directed
with all leads, lifts etc. complete.
Spec. No.: BdW- 8 Page No. 716
23 Removing cement tiles, or marble or polished Sq.Mt. 20.00 20.00
shahabad floor or dado without bed concrete
including stacking the materials as directed with all
leads, lifts, complete.
Spec. No.: As directed by Engineer in charge
24 Removing Shahabad or Tabdur stones from floor Sq.Mt. 19.00 19.00
without bed concrete including stacking the
materials as directed with all leads, lifts, complete.
Spec. No.: As directed by Engineer in charge.
144
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
28 Removing wire fencing with iron/C.C. fencing posts R.Mt. 28.00 28.00
and stacking the materials as directed with all leads,
lifts complete.
Spec. No.: As directed by Engineer in charge.
29 Removing iron pipe railing having wooden R.C.C. or R.Mt. 29.00 29.00
C.C. or iron posts and stacking the materials as
directed.
Spec. No.: As directed by Engineer in charge.
30 Removing earthen, stoneware pipes and stacking No. 10.00 10.00
them as directed with all leads, lifts, complete.
Spec. No.: As directed by Engineer in charge.
31 Removing cast iron or wrought iron or A.C. pipe and R.Mt. 10.00 10.00
stack-ing them as directed with all leads, lifts,
complete.
Spec. No.: As directed by Engineer in charge.
32 Dismantling the R.C.C. work 1:2:4 and sorting out Cu.Mt. 614.00 602.00
the materials such as steel etc. as directed and
stacking them within the specified lead as directed.
Spec. No.: As directed by Engineer in charge.
145
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
37 Removing purlins from roof including stacking as R.Mt. 9.00 9.00
directed with all leads, lifts, etc. complete.
Spec. No.: As directed by Engineer in charge.
38 Removing rafters from roof including the materials R.Mt. 9.00 9.00
as directed with all leads, lifts, etc. complete.
Spec. No.: As directed by Engineer in charge.
39 Removing cloth partition with frame work and Sq.Mt. 8.00 8.00
stacking the materials as directed with all leads, lifts
etc. complete.
Spec. No.: As directed by Engineer in charge.
40 Providing and fixing Jute Kanthan (Tarat) screen to Sq.Mt. 42.00 10.00
the scaffold-ing for external guniting as directed
including removing the same after the work is over
etc complete.
Spec. No.: As directed by Engineer in charge
41 Removing Urinal Pans or W.H.B. with frame No. 53.00 51.00
including disconnecting the sanitary and water
supply connections. removing the same carefully
and stacking the serviceable materials as and where
directed including throwing the unserviceable
materials out side.
Spec. No.: As directed by Engineer in charge.
42 Removing W.C. Pan including disconnecting the No. 88.00 85.00
sanitary and water supply connections, removing
and breaking flooring and bed con-crete around pan
removing the same carefully and stacking the
service-able materials as and where directed
including of throwing the unserviceable materials out
side.
Spec. No.: As directed by En-gineer in charge.
43 Dismantling existing brick bat coba in the W/C and No. 895.00 877.00
toilets including removing the dismantelled stuff
outside the rooms, including stacking and cleaning
surface etc. complete.
Spec. No.: As directed by Engineer in charge.
146
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
44 Scraping old paint from steel and other metal Sq.Mt. 35.00 34.00
surface with flame, cleaning and making the surface
even and scaffolding etc. complete.
Spec. No.: BdW- 8 Page No. 716
45 Cleaning steel and concrete surface of columns,
beams, ceilings etc. ------------ including washing
with pressured water including machinery, all lead,
labour, scaffolding etc. complete.
Spec. No.: As directed by Engineer-in-charge
a by compressed sand blasting Sq.Mt. 124.00 29.00
b by manually Sq.Mt. 66.00 64.00
46 Scraping the old surfae with sand paper and coating Sq.Mt. 8.00 8.00
it with mixture of whiting or glue and linseed oil
including scaffolding etc. complete.
Spec. No.: BdW-8 Page No. 716
47 Removing grass gazer grass and disposing off out Sq.Mt. 4.00 4.00
of build-ing premises including making clean the
ground by showel and phavaras etc. complete.
Spec. No.: As directed by Engineer in charge.
48 Labour charges for applying two coats of alluminium No. 289.00 283.00
paint for flag-post including preparing the surface
and primer coat etc. complete.
Spec. No.: As directed by Engineer in charge.
147
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
50 Providing and applying one coat polymer based Sq.Mt. 125.00 18.00
polysafe-plastone bonding chemical to concrete
surface including cleaning the existing surface by
grinding / wire brushing etc. complete as directed.
Spec. No.: As directed by Engineer-in-charge
148
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
54 Guniting by dry mix process as per I.S. 9012 (1978)
to the vertical surface (other than column) in C.M.
1:3, 20 mm. thick under pressure of 2.1 Kg. to 2.8
Kg per sq.cm. including forms, scaffolding, floating,
the surface curing for 14 days etc. complete.
(excluding reinforcement).
Spec. No.: Bd.W.2 Page No. 710
a 20 mm Sq.Mt. 350.00 113.00
b 25 mm Sq.Mt. 370.00 111.00
55 Providing preconstructional antitermite treatment Sq.Mt. 50.00 3.00
as per I.S. 6313 (Part-II) by treating the bottom
surface and sides of excavation
clorophyriphoas/lendene at the rate of 5 litres of
emulsion concentrates of 0.5 percent of Aldrin per
square meter of surface area covering 10 years
guarantee.
Spec. No.: As directed by Engineer in charge.
56 Providing preconstructional antitermite treatment Sq.Mt. 75.00 7.00
as per I.S. 6313 (Part-II) treatment by treating the
backfill in immediate contact with foundation at the
rate of 7.5 litres off emulsion concentrate of 0.5
percent of Clorophyriphas/ Hephoclore per square
metre of vertical surface are covering 10 years
guarantee.
Spec. No.: As directed by Engineer in charge.
57 Providing preconstructional antitermite treatment Sq.Mt. 50.00 4.00
as per I.S. 6313 (Part-II) by treating the top surface
of plinth filling at the rate of 5 litres of emulsion
concentrate at 0.5 percent of Hephoclore per square
metre of surface area covering ten years guaran-
tee.
Spec. No.: As directed by Engineer in charge.
149
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
58 Providing preconstructional antitermite treatment Sq.Mt. 98.00 14.00
as per I.S. 6313 (Part-I) to the soil along the external
face of building by punching holes of 1.2 of 1.5
C.M. diametre about 30 percent of Clorophysiphas/
20 E.C. Heptaclor at the rate of 7.5 litres emulsion
concentrate per hole and sealing the same with
proper filling & covering 10 years guarantee.
Spec. No.: As directed by Engineer in charge.
150
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
62 Providing antitermite treatment around the R.Mt. 30.00 16.00
periphery of the existing building as per I.S. 6313
(Part-III) by excavating trenches of 20cm width and
exposing the sides of columns and plinth beams
upto a depth of 300mm and injecting one percent of
chlorodane emulsion concentrate at the rate of 2.25
litres per Rmt and refilling the trenches etc.
complete covering 2 years guarantee.
Spec. No.: As directed by Engineer in charge.
151
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
66 Providing and erecting 1.5 metre high wire fencing R.Mt. 537.00 113.00
with seven rows of barbed wire supported on
M.S.Angles (50 mm x 50 mm x 6mm) at 2.5 Metres,
center to center including excavating pits for
foundation, fixing post in cement concrete 1:4:8 of
size 45 x 45 x 45 cm . fastening the wire and
painting the M.S.Angles with one coat of red lead
primer and two coats of painting etc. complete.
Spec. No.: Bd.W.3 Page No. 712
67 Providing and erecting chain link fencing 1.6 M. R.Mt. 1629.00 0.00
height with G.I. chain link of size 50 x 50 mm 8
guage thick and fixed 75 mm above Ground level
vertical M.S Angle of 40 x 40 x 6 mm size
embedded in C.C. block of 1:4:8 mix of size 450 x
450 x 670 mm. at 1.75 M.c/c with iron bar 16 mm
dia as hold fast including welding link with angle
frame at 30 cm c/c nuts and bolts and horizontal
M.S. Angles at top and bottom of 25 x 25 x 5 mm
size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm
horizontal including cross support of 40 x 40 x 6 mm
Angles both sides at every corner or bends
embedded in concrete blocks of 1:4:8 of size 450 x
450 x 670 mm including 3 coats of oil painting etc.
complete.
Spec. No.: As directed by Engineer in charge.
68 Providing and erecting 1.2 meter high wire fencing R.Mt. 437.00 98.00
with five rows of barbed Wire supported on mild
steel angle post including excavation of pits of
foundation concrete fixing the posts in (1:4:8)
cement concrete block and fastening the Wires.
Spec. No.: Bd. W. 3, Page No. 712
152
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
69 Providing and erecting concertina coil 'Y' type R.Mt. 745.00 83.00
barbed wire fencing 1.5 meter high with seven
rows of wire with 2.45 mm dia ( Rezan/
concentina ire 0.60 mm dia ) with hot dip and G.I.
coated hooks as per drawing supported on M.S.
angle 50 x 50 x 6 mm at 2.5 mtr. c/c including fixing
and fastening with wire, painting M.S. angles with
one coat of red lead primer and two coat of oil paint
etc. complete. (Excluding C.C. Block)
Spec. No.: As directed by Engineer in charge.
70 Providing and fixing rain tattis with bamboos and Sq.Mt. 56.00 11.00
karve grass with 75 mm thick grass and removing
the same after rain is over (size of bamboos 50mm
to 75mm. dia and 3 M to 3.5 M. long.
Spec. No.: As directed by Engineer in charge.
71 Providing and fixing grass chhapper (roof) with Sq.Mt. 74.00 12.00
necessary bamboos and karve frame with 75 mm.
thick grass etc, removing the same after rain is over
(size of bamboos 50 mm to 75 mm dia and 3 M to
3.5 M. long.)
Spec. No.: As directed by Engineer in charge.
72 Providing and fixing grass chhapper (roof) with Sq.Mt. 66.00 9.00
necessary bamboos and karve frame with 75 mm.
thick grass etc, removing the same after rain is over
(size of bamboos 25 mm dia and 3 M. to 3.5 M. long
Spec. No.: As directed by Engineer in charge.
73 Providing and fixing Bamboo Matting screen for Sq.Mt. 112.00 71.00
partition with bamboo sticks.
Spec. No.: As directed by Engineer in charge.
153
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
74 Providing and fixing lightening conductor system No. 15141.00 2335.00
comprising of errecting Air-Termination consisting of
tubular copper rod of 25mm dia. 1.2mm thick with
multiple points head 1.2mt. long (Heavy Duty)
welded or clamped to G.I. pipe pole B Grade 50mm
dia. of reqd. length with M.S. round base plate
25cm. diam. and 10cm thick at bottom embeded in
cement concrete 1:3:6 foundation of size 45cm
diam. x 45cm Height and providing earthing with
copper earth plate of size 60 x 60 x 0.3cms with
cadmium plated nut bolts to fix earthing strip burried
in specially prepared earth pit 1.5 metre below
ground level with 40 Kg charcoal and salt with
alternate layers of charcoal and salt and G.I. pipe
40mm dia. 2mt. length burried in earth upto earthing
plate remaining portion above ground level for
watering and refilling complete.
Spec. No.: BDW 1 Page 709
75 Providing and fixing copper strip 25 mm wide and R.Mt. 112.00 41.00
3 mm thick for lightening conductor including fixing
with screws required scaffolding etc. complete.
Spec. No.: BDW 1 Page 709 as directed Enginner in
charge
76 Providing and fixing in position alluminium strips of R.Mt. 568.00 124.00
size 50 mm. x 3 mm. for nosing of steps including
fixing with screws and raval plugs, bending and
cutting to the required shape and size, finishing etc.
complete.
Spec. No.: As directed by Engineer in charge.
77 Providing and fixing crimped wire G.I. mesh of size Sq.Mt. 680.00 312.00
20mm x 20mm 10 guage to iron angle frame
including welding crimp mesh to angle frame and
steel flat, fixing the frame in its original position and
oil painting etc. complete. (excluding cost of
structural steel)
Spec. No.: As directed by Engineer in charge.
154
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
78 Providing and fixing 90 cm. x 60 cm. Marble plate No. 7302.00 6293.00
engraving 10cm. height letter, figures including
painting the letters/figures with approved colour and
shade complete.
Spec. No.: Bd.W.7 Page No. 715
79 Providing and fixing 90 cm. x 60 cm. Granite plate No. 8095.00 6468.00
engraving 10cm. height letter, figures including
painting the lefters/figures with approved colour and
shade complete.
Spec. No.: Bd.W.7 Page No. 715
80 Lowering debris of the existing water proofing Cu.Mt. 148.00 143.00
treatment from the terrace by any means without
causing dust nuisance and damages to structure,
stacking the same as and where directed including
cleaning the site etc. complete.
Spec. No.: BdW- 8 Page No. 715
81 Providing & Fixing PVC sheet wall Paneling pf Sq.Mt. 1393.00 427.00
thickness 5mm consisting of paneis having size
1220mm X 2440mm stuck
Spec. No.: As directed by Engineer-in-charge
82 Providing and fixing 40mm diameter and 1.5mm R.Mt. 650.00 320.00
thick Stainless steel railing in S.S.304 Grade
including fabricating ,fixtures, errecting , necessary
welding , griding , finishing, buffing to stainless steel
pipe etc. complete.
Spec. No.: As directed by Engineer Incharge
155
Bd - W : Miscellaneous
ITEM Final Rate (2015-16)
Description Unit
NO.
Completed Labour
1 2 3 4 5
83 Providing, fabricating and supplying and fixing Sq.Mt. 4473.00 756.00
panels of aluminium composite panel (ACP)
cladding in pan shape in metalic colour of approved
shades made out of 4mm thick aluminium
composite panel material consisting of 3mm thick
FR grade mineral core sandwiched between two
aluminium sheets (each 0.50mm thick). The
aluminium composite panel cladding sheet shall be
coil coated with kynar 500 base PVDF / Lumiflon
based fluoropolymer resin coating of approved
colour and shade on face 1 and polymer (service)
coating on face 2 as specified using steinless steel
screws, nuts, bolts, washers, cleats, weather silicon,
sealent, backer rods etc. The supporting frame
structurre shall be made of aluminium rectangular
section 38 x 38 mm. The fastening brackets of
aluminium alloy 6005 T5/ MS with hot deep
galvinised
84 Carring out the Structural Audit of buildings with Sq.Mt. 42.00 0.00
a)Visually inspecting the Building for structural
inconsistancy . Overloading abnormal exposure
safety consideration .
b) Non destractive testing
c) Preparing final report
d) Preparing BOQ for the structural repairs
suggested
e) submtting all drawings report in 10 copies
156
ROAD WORKS
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
1 Picking the road surface including sectioning etc.
complete.
Spec. No.: Rd. 30 Page No. 381/2012
a on W.B.M. surface Sq.Mt. 10.00 9.00
b on B.T.surface Sq.Mt. 13.00 11.00
c on murum surface Sq.Mt. 5.00 4.00
2 Cutting Down trees With girths of ……………….. cm
including trunck and branches and stacking the
materials neatly within a lead of 50m. as directed
etc.complete.
Spec. No.: RD-1 Page No. 349/2012
a 30 to 60 cm. No. 423.00 307.00
b 60 to 90 cm No. 559.00 405.00
c 90 to 180 cm. No. 716.00 577.00
d 180 to 270 cm. No. 781.00 573.00
e 270 to 450 cm No. 857.00 638.00
f above 450 cm. No. 939.00 695.00
3 Excavation for roadways by...... such as ...... including
dressing section to the required camber and side slopes
and conveying the excavated materials with all lifts upto
a lead of 50 m and spreading for embankment,
disposing as directed etc. complete.
Spec. No.: Rd. 2 Page No. 351/2012
A By manual means
i) earth soil of all sorts sand, gravel or soft murum Cu.Mt. 113.00 100.00
ii) hard murum Cu.Mt. 122.00 108.00
iii) hard murum and boulders Cu.Mt. 136.00 120.00
iv) soft rock Cu.Mt. 282.00 249.00
B By Mechanical means
i) earth soil of all sorts sand, gravel or soft murum Cu.Mt. 60.00 26.00
ii) hard murum Cu.Mt. 66.00 28.00
iii) hard murum and boulders Cu.Mt. 72.00 34.00
iv) soft rock Cu.Mt. 140.00 110.00
157
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
4 Excavation for roadways in hard rock ......including
dressing section to the required camber and side slopes
and conveying the excavated materials with all lifts upto
a lead of 50 m and spreading for embankment or
stacking disposing as directed. Spec.
No.: Rd. 6 Page No. 356/2012
a by blasting No. 492.00 337.00
b by weding chislling or line drilling No. 800.00 578.00
5 Preparing embankment with approved materials Cu.Mt. 40.00 26.00
obtained from the cutting within a lead of 50m including
all lifts,laying layer of 20 to 30 cm. thickness, breaking
clods, dressing to the required lines, curves, grade &
section with normal watering and compaction
etc.complete.
Spec. No.: Rd.14 Page No. 367
6 Providing earth work in embankment with approved Cu.Mt. 90.00 72.00
materials obtained from private land / departmental
land including all lifts and 50.m lead laying in layers of
15cm to 20cm. thickness breaking clods and dressing to
the required lines, curves, grade & section with normal
watering and compaction etc. complete.
Spec. No.: Rd.16 Page No. 368
7 Providing earth work in embankment with approves
materials obtained from departmental land or other
sources specifaied by Engineer-in-chnge, upto lead of
50 m. including all lifts, laying in layers of 20 to 30 cm
thickness, breaking clods, dressing to the required lines,
curves, grade & section, watering and compacting
by.....to 95% of standard proctor density etc.complete.
Spec. No.: Rd.12 Page No. 361/2012
158
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
8 Providing earth work in embankment with approves
materials obtained from departmental land or other
sources specifaied by Engineer-in-chnge, upto lead of
50 m. including all lifts, laying in layers of 20 to 30 cm
thickness, breaking clods, dressing to the required lines,
curves, grade & section, watering and compacting by......
to 100% standard proctor density etc.complete.
Spec. No.: Rd.12 Page No. 361/2012
159
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
12 Watering and compacting of embankment formed of
materials obtained from the road cutting, within a lead of
50m to 100% of standard proctor density after laying
them in layers of 20 to 30 cm with etc. complete.
Spec. No.: Rd.10 Page No. 359/2012
160
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
17 Supplying stone dust of trap stone aggregate at the Cu.Mt. 190.00 4.00
road side, including conveying and stacking etc.
complete for use in bituminous road surface.
As directed by Engineer-in-charge.
18 Supplying hard murum/kankar at the road side, Cu.Mt. 91.00 2.00
including and stacking etc. complete.
Spec. No.: Rd. 23 Page No. 375/2012
19 Supplying gravel at the road side, including conveying Cu.Mt. 160.00 7.00
and stacking etc. complete.
Spec. No.: Rd. 26 Page No. 377
20 Laying 15 to 23 cm. trap stone/ laterial stone rubble Cu.Mt. 125.00 111.00
soiling including hand packing with rubble chips etc.
complete.
Spec. No.: Rd. 27 Page No. 378/2012
21 Spreading oversize and size 40mm / 50mm / 60mm / Cu.Mt. 48.00 42.00
80mm metal including sectioning etc. complete.
Spec. No.: Rd. 29 Page No. 379
22 Spreading gravel / hard murum / soft murun & stone Cu.Mt. 29.00 26.00
dust over the rubble soiling,oversize and size metal layer
/ blandage on W.B.M. surface etc.complete. Spec.
No.: Rd.28 Page No. 379
23 Spreading gravel / hard murum / kankar on the road Cu.Mt. 27.00 24.00
formation / side width.
Spec. No.: Rd.28 Page No. 379
24 Compacting sub grade / gravel / oversize metal
(200mm loose) layer 2 to 7 m wide with ……... including
necessary, labour, materials and artificial watering etc.
complete.
Spec. No.: Rd. 30 Page No. 380
a static roller Sq.Mt. 14.00 4.00
b By Vibratory Roller. Sq.Mt. 20.00 5.00
25 Compacting the size metal (150 mm loose) layer upto Sq.Mt.
2.00m width with static roller, including necessary labour,
meterials and artificial watering etc.complete.
Spec. No.: RD 30 Page 380
161
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
26 Compacting the hard murum / kankar 2.00m to 7.00
width (200mm loose) with static roller including artificial
watering etc.complete.
a static roller Sq.Mt. 6.00 1.00
b Vibratory roller Sq.Mt. 8.00 2.00
27 Compacting the hard murum side width, layer wise on Sq.Mt. 8.00 3.00
each side with Vibratory Roller. roller including artificial
watering etc. complete.
As directed by Engineer-in-charge.
Providing, laying, spreading and compacting of granular
sub-base by providing close graded Material, mixing in a
mechanical mix plant at OMC, carriage of mixed Material
to work site, spreading in uniform layers with motor
grader on prepared surface and ompacting with
vibratory power roller to achieve the desired density,
complete as per MoRT&H specification clause - 401
including all material, labour,machinery, lighting,
guarding and maintenance of diversion.
Spec. No.: MORT&H-401
162
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
29 Providing, laying, spreading and compacting stone
aggregates of specific sizes to water bound macadam
for...... specification including spreading in uniform
thickness, hand packing rolling with 3 wheeled
steel/vibratory roller 8-10 tonnes in stages to proper
grade and camber, applying and brooming requisite type
of screening/ binding Materials to fill up the interstices of
coarse aggregate, watering and compacting to the
required density to protect edges, lighting, guarding,
barricading and maintenance of diversion etc. complete.
..... as per techenical specification Cl. No. 405A
....................
A Grading 1
i By Manual means. Cu.Mt. 1338.00 286.00
ii By Mechanical means. Cu.Mt. 1204.00 257.00
B Grading II
i By Manual means. Cu.Mt. 1405.00 299.00
ii By Mechanical means. Cu.Mt. 1265.00 269.00
30 Providing and laying......... milimeter thick modified
penetration macadam over prepaied based by spreading
size metal layers of 40 mm nominal size of 30% crusher
broken and 70% Hand broken with compaction with
power roller heating and spraying bitumen with sprayer
@ of 200 kg per 100 Sq.mtr. spraying key aggregate (12
mm size chips) and final compaction with power roller
(Spec. No. IRC-SP-20/2002 appendix 8.4 Page No. 215)
163
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
i) over W.B.M. surface. Sq.Mt. 149.00 21.00
ii) Over B.T. surface Sq.Mt. 173.00 24.00
b 75 mm thick
i) over W.B.M. surface. Sq.Mt. 183.00 25.00
ii) Over B.T. surface Sq.Mt. 193.00 27.00
31 Providing 50 mm. thick semi grout bituminous road
surface including supplying all materials, preparing the
existing road surface, laying the required thickness of
metal layer, heating & spraying bitumen spreading chips
laying seal coat & compacting complete. 2) Using Bulk
Bitumen grade (30/40) VG-40
Spec. No.: Rd.48 Page No. 398
164
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
a 50 Kg/100 sqmtr over B.T. surface Sq.Mt. 37.00 11.00
b 75 Kg/100 sqmtr over W.B.M. surface Sq.Mt. 52.00 13.00
35 Providing and applying primer coat with bitumen
emulsion on prepared surface of granular Base including
clearing of road surface and spraying primer using
mechanical means (Reference to MORT&H's
specification clause 502).
165
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
38 Providing and laying 50-75 mm compacted thick design Cu.Mt. 7298.00 49.00
mix (approved by Engineer) Dense Bituminous
Macadam on prepared surface with specified graded
crushed aggregates as per Table 500- 9, 500-10 with
bitumen binder set (including cost of anti-stripping
compound wherever required) for base/ binder course
including loading of material with F.E. loader, heating
and mixing of stone aggregate, filler and bitumen in
computerised hot mix plant, transporting the mixed
material by tippers to paver and laying with paver finisher
fitted with electronic sensor control as per clause 504.3.5
to the required level and grade, compacting by power
rollers and vibratory rollers or 150 to 250 KN pneumatic
tyred roller with TP 0.7 Mpa to achieve the desired
density (approximately 2.3
tonne/cum) complete as per clause 505 of MoRT&H
specification but excluding primer/tack coat, including all
material, labour, machinery, lighting, guarding and
maintenance of diversion. Grade-II with Bitumen VG-
grade 30 @ 4.50 %, lime filler @ 2%
(percent by weight of total mix)
166
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
40 Providing and laying 30-45 mm compacted thickness Cu.Mt. 8473.00 50.00
Bituminous Concrete as per design mix (approved by
Engineer) on prepared surface with specified grade
stone aggregate as per Table - 500-18 with bitumen for
wearing course including loading of aggregate with F.E.
loader and hot mixing of stone aggregate and bitumen
(including cost of anti-stripping compound wherever
required) in computerised hot mix plant, transporting the
mixed material by tippers to paver and laying with paver
finisher fitted (as per clause 504-3.5) to the required
level and grade and compacting by power rollers and
vibratory rollers or 150 to 250 KN pneumatic tyred roller
with TP = 0.7 Mpa, to achieve the desired density
complete as per clause 509 of MoRT&H specification
including all material, labour, machinery, lighting,
guarding and maintenance of diversion but excluding
primer/tack coat Grade-II with Bitumen VG-grade 30 @
5.40 % (percent by weight of total
mix)
167
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
of 14 days,fixing dowels,tie-bars,cutting joints,joint-
fillers,sealants and all types of joints and finishing to the
desired surface texture including all
material,labour,machinery with all leads and lifts etc
complete.With Scada (Prior permission of S.E. is
essential )
Spec. No.: MORT&H Clause 602
a Without flyash Cu.Mt. 6408.00 1130.00
b With flyash Cu.Mt. 6034.00 1130.00
42 Providing and laying in situ cement concrete road
pavement of Using Concrete Mixer ....... grade,including
supplying all materials, providing steel form work,
compaction by plate vibrator, providing joints at every
thirty meters internal and filling the joints with
bitumen,curing etc.complete. (Excluding cost of
reinforcement) (Newly laid concrete shall be covered by
gunny bag/plastic sheet/tarpaulin etc. for curing period
complete.)
Spec. No.: As directed by Engineer-in-charge
a PCC M20 Cu.Mt. 5366.00 1080.00
b PCC M25 Cu.Mt. 5565.00 1007.00
c PCC M30 Cu.Mt. 5737.00 1021.00
d PCC M35 Cu.Mt. 5830.00 1046.00
43 Providing and laying in situ cement concrete road
pavement of Using Batching plant,transit mixer and
concrete pump.(RMC) .......... grade,including supplying
all materials, providing steel form work, compaction by
plate vibrator, providing joints at every thirty meters
internal and filling the joints with bitumen,curing
etc.complete. With SCADA with fully automatic micro
processor based PLC attachment (Excluding cost of
reinforcement) (Newly laid concrete shall be covered by
gunny bag/plastic sheet/tarpaulin etc. for curing period
complete.) Prior Approval of S.E.'s essential
Spec. No.: As directed by Engineer-in-charge
168
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
c PCC M30 Cu.Mt. 5276.00 831.00
d PCC M35 Cu.Mt. 5363.00 823.00
44 Providing R.C.C.(M-15) 5th kilometer stone of standerd No. 3890.00 743.00
design as per IRC:8-1980,fixing in c.c.M15,including
painting and printing etc.complete. Spec. No.: IRC:8-
1980
45 Providing R.C.C.(M-15) Ordinary kilometer stone of No. 2459.00 455.00
standerd design as per IRC:8-1980,fixing in
c.c.M15,including painting and printing etc.complete.
Spec. No.: IRC:8-1980
46 Providing R.C.C.(M-15) 200 meter stone of standerd No. 641.00 160.00
design as per IRC:8-1980,fixing in c.c.M15,including
painting and printing etc.complete.
Spec. No.: IRC:8-1980
47 Providing R.C.C.(M-15) Boundary stone of standerd No. 400.00 131.00
design as per IRC:8-1980,fixing in c.c.M15,including
painting and printing etc.complete.
Spec. No.: IRC:8-1980
48 Providing and fixing M-15 R.C.C. Guard stone of 20 x No. 425.00 98.00
20 x 75 cms including fixing in ground and white washing
etc.Complete. Spec. No.:
IRC:8-1980
49 Providing and Fixing of Retro Reflectorised 900 mm No. 6420.00 110.00
Octagon Stop Sign boards made out of retro reflective
sheeting of High Intensity prismatic grade conforming to
IRC-67: 2012 & Type IV standards of ASTM D4956-09
specifications, fixed over 2 mm thick Al / 4mm thick
ACP sheet supported with Back support frame of
25x25x3mm mild steel angle as approved , supported on
a mild steel angle iron post 75 mm X 75 mm X 6 mm -
2.7 mtr height, firmly fixed to the ground by means of
properly designed foundation with M20 grade cement
concrete 45 cm X 45 cm X 60 cm , 60 cm below ground
level as per approved drawing. 7 years Warranty for
Retro Reflective Sheeting from the original sheeting
manufacturer & a certified copy of three years outdoor
exposure report
169
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
from an independent test lab for the product offered shall
be submitted by the contractor Stop boards of 90 cm
Octagon.
Spec. No.: IRC-67 of 2012
50 Providing and Fixing of Retro Reflectorised 300 X 900 No. 3512.00 110.00
mm Hazard Marker boards made out of retro reflective
sheeting of High Intensity prismatic grade conforming to
IRC-67: 2012 & Type IV standards of ASTM D4956-09
specifications, fixed over 2 mm thick Al / 4mm thick
ACP sheet supported with Back support frame of
25x25x3mm mild steel angle as approved , supported on
a mild steel angle iron post 75 mm X 75 mm X 6 mm -
2.7 mtr height, firmly fixed to the ground by means of
properly designed foundation with M20 grade cement
concrete 45 cm X 45 cm X 60 cm , 60 cm below ground
level as per approved drawing. 7 years Warranty for
Retro Reflective Sheeting from the original sheeting
manufacturer & a certified copy of three years outdoor
exposure report from an independent test lab for the
product offered shall be submitted by the contractor
Hazard Marker boards of 30 x 90 cm Rectangle.
Spec. No.: IRC-67 of 2012
51 Providing and Fixing of Retro Reflectorised 600 X 800 No. 5114.00 110.00
mm Facility sign boards made out of retro reflective
sheeting of High Intensity prismatic grade conforming to
IRC-67: 2012 & Type IV standards of ASTM D4956-09
specifications, fixed over 2 mm thick Al / 4mm thick
ACP sheet supported with Back support frame of
25x25x3mm mild steel angle as approved , supported on
a mild steel angle iron post 75 mm X 75 mm X 6 mm -
3.5 mtr height, firmly fixed to the ground by means of
properly designed foundation with M20 grade cement
concrete 45 cm X 45 cm X 60 cm , 60 cm below ground
level as per approved drawing. 7 years Warranty for
Retro
170
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
Reflective Sheeting from the original sheeting
manufacturer & a certified copy of three years outdoor
exposure report from an independent test lab for the
product offered shall be submitted by the contractor
Facility Sign boards of 60 x 80 cm Rectangle. Size 60 x
80 cms. Rectangle
Spec. No.: IRC - 67 of 2012
171
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
grade cement concrete 45 cm X 45 cm X 60 cm , 60 cm
below ground level as per approved drawing. 7 years
Warranty for Retro Reflective Sheeting from the original
sheeting manufacturer & a certified copy of three years
outdoor exposure report from an independent test lab for
the product offered shall be submitted by the contractor
Regulatory sign boards of 90 cm Diameter.
Spec. No.: IRC-67 of 2012
54 Providing and Fixing of Retro Reflectorised direction & place Sq.Mt. 9139.00 110.00
identification sign boards made out of retro reflective
sheeting of High Intensity prismatic grade conforming to IRC-
67: 2012 & Type IV standards of ASTM D4956-09
specifications, fixed over 2mm thick Al / 4 mm thick ACP
sheet supported with Back support frame of 35x35x5mm mild
steel angle with areas not exceeding 0.9 sqm. Supported in
mild steel angle iron post 75x75x6mm - 3.5 mtr height ,firmly
fixed to the grounf by means of properly designed foundation
of M20 grade cement concrete 45 cm X 45 cm X 60 cm , 60
cm below ground level complete (as per MoRT&H
specification No.801) (for area Less than 0.9 sqm). 7 years
Warranty for Retro Reflective Sheeting from the original
sheeting manufacturer & a certified copy of three years
outdoor exposure report from an independent test lab for the
product offered shall be submitted by the contractor. Direction
Sign boards below 0.9 Sq.Mtr
Spec. No.: IRC-67 of 2012
55 Providing and Fixing of Retro Reflectorised direction & place Sq.Mt. 10980.00 145.00
identification sign boards made out of retro reflective sheeting
of High Intensity prismatic grade conforming to IRC-67: 2012
& Type IV standards of ASTM D4956-09 specifications, fixed
over 2mm thick Al / 4 mm thick ACP sheet supported with
Back support frame of 35x35x5mm mild steel angle with
areas not exceeding 0.9 sqm. Supported in mild steel angle
iron post 75x75x6mm - 3.5 mtr height & with MS angle of
50x50x5mm bracing,firmly
172
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
fixed to the grounf by means of properly designed
foundation of M20 grade cement concrete 45 cm X 45
cm X 60 cm , 60 cm below ground level complete (as
per MoRT&H specification No.801) (for area more than
0.9 sqm). 7 years Warranty for Retro Reflective
Sheeting from the original sheeting manufacturer & a
certified copy of three years outdoor exposure report
from an independent test lab for the product offered shall
be submitted by the contractor. Direction Sign boards
Spec. No.: IRC-67 of 2012
56 Providing & Fixing informatory sign boards in square or Sq.Mt. 4356.00 556.00
rectragular shape of any size made out 16 quage (1.6
mm) thick mild steel sheet painted with one coat of zinc
chromate stoving primer and two coats green back
ground white boarder/messages,symbols etc. and back
side in grey stove enamel paint in cluding M.S.angle
frame of 35 mm x 35 mm x 3 mm and two M.S.angle
iron post of size 50 mm x 50 mm x 5 mm. 3.65 m long
properly cross braced with angle iron of size 50 mm x 50
mm x 5 mm duly painted with alternate black and white
bands of 25 cm width including G.I.fixtures etc. and
fixing the board in 1:4:8 concrete block of size 60 cm x
60 cm x 75 cm including transportation etc.complete
57 Providing Vertical Delineator having wide angle cube No. 1350.00 0.00
corner micro prismatic non metallic reflective sheeting
confirming to Type XI of ASTM D4956 -09 with White
Color and Red Color combination and having minimum
of retro reflective exposed area of 125 Sq CM on top
slots & 35 Sq CM on bottom slots and no edges shall be
exposed for tampering. This tubular delineator shall have
a core and shell construction, shell shall be made of
tough, high impact resistant, injection-molded,
thermoplastic outer body & the inner core shall consist of
powder coated or painted Mild steel of
173
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
minimum thickness 1.0mm.& core-shell structure shall
be of height not less than 800 mm above the ground and
width not less than 80 mm. The metallic core of the
delineator shall extend 300mm beyond the shell length
from bottom for installing in the ground. The extended
portion shall have slots to insert anchoring rods for
enhancing the concrete grip. The logo of the
manufacturer shall be embossed on either side of the
The engineering thermoplastic used for making the
delineator body shall have minimum initial mechanical
properties of 600J/m tested in accordance with ASTM
D256 and shall retain at least 70% of these minimum
initial values when subjected to accelerated weathering
for 1000hrs as per ASTM G155 or UL 746C and as per
IRC 79 specifications and including fixing the unit in M20
Grade Cement Concrete of Size 30x30x40 cm including
excavation for pit. Vertical Delineators
174
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
The Median Marker shall have rectangular-shaped,
fluorescent yellow color retro-reflective sheeting of size
not less than 8.5cm*8.5cm and with fully reflective micro
prismatic cube corners as its retro-reflective elements as
per IRC 67 2010 and ASTM D4956 type XI
specifications reflectivity values. The retro-reflective
sheeting shall be one or both sides of the Median Marker
and shall be edge protected with no exposed edges
which will prevent edge lifting, vandalism, sheeting
damage, etc. The Median Marker shall be fixed by a
combination of epoxy adhesive and grouting. Median
Marker
Spec. No.: As directed by Engineer-in-charge
59 Supplying & Fixing of Molded Shank Raised Pavement No. 638.00 13.00
Markers made of polycarbonate and ABS moulded body
and reflective panels with micro prismatic lens capable
of providing total internal reflection of the light entering
the lens face and shall support a load of 16000 kg tested
in accordance to ASTM D 4280 Type H and complying
to Specifications of Category A of MORTH Circular No
RW/NH/33023/10-97 – DO III Dt 11.06. 1997. The
height, width and length shall not exceed 50 mm, 100
mm and 102 +/- 2 mm and with minimum reflective area
of 13 Sqcm on each side and the slope to the base shall
be 35 +/- 5 degree. The strength of detachment of the
integrated cylindrical shanks, (of diameter not less than
19 +/- 2 mm and height not less than 30+/- 2 mm) from
the body is to be a minimum value of 500 Kgf. Fixing will
be by drilling holes on the road for the shanks to go
inside, without nails and using epoxy resin based
adhesive as per manufacturer’s recommendation and
complete as directed by the engineer. Twin Shank RPM
(Cat Eye)
Spec. No.: As directed by Engineer-in-charge
175
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
60 Providing and lyaing of hot applied themoplastic
compound 2.5mm thick Yellow / White including
reflectorising glass beads @250 gms.per sqm
area,thickness of 2.5mm is exclusive of surface applied
glass bead as per IRC 35. The finished surface to be
level, uniform and free from streaks and holes
etc.complete with 3 years gruantee Spec. No.:
MORTH CI.803 Page 388/2012
a White Sq.Mt. 1100.00 0.00
b Yellow Sq.Mt. 1155.00 0.00
61 Providing and painting center line,dashes,arrows etc.in
two coats on new / old work with ready mix road marking
paint conforming to IS:164 on bituminous
surface,including cleaning the surface of all dirt,dust and
other forein matter demarcation at site and traffic control
involved etc.complete.(10 cm.in width)
Spec. No.: MORTH 803
176
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
65 Painting Two Hundred Meter stone with approved No. 88.00 53.00
enamel paint in two coats and lettering including
cleaning surface etc.complete.
Spec. No.: As directed by Engineer-in-Charge.
66 Painting Boundry stone with approved enamel paint in No. 44.00 25.00
two coats and lettering including cleaning surface
etc.complete.
Spec. No.: As directed by Engineer-in-Charge.
67 Providing oil painting to the plain surface of cement
plaster, wooden planks, steel sheets etc. complete in
two coats with superior grade oil paints.Rate for Painting
the letters as under
Spec. No.: As directed by Engineer-in-Charge.
i For lettering upto 5 cm.hegight No. 7.00 3.00
ii For lettering 5 t0 7.5 cm.hegight No. 9.00 3.00
iii For lettering 7.5 to 10 cm.hegight No. 12.00 3.00
iv For lettering 10 to 12.50 cm.hegight No. 13.00 3.00
68 Providing and colour washing to road side in 2 coats in Sq.Mt. 18.00 10.00
2 bands of white and one red band at center of 30cm
height each including preparing the surface, cost of
material, conveying etc.complete.
Spec. No.: As directed by Engineer-in-Charge.
69 Providing white washing the parapets of bridges, Sq.Mt. 17.00 4.00
culverts and parapet in two coats of approved colour
washing etc.complete.
Spec. No.: As directed by Engineer-in-Charge.
70 Providing dry Trap rubble stone pitching 23 cm thick as Sq.Mt. 142.00 41.00
directed etc.complete. Spec.
No.: Rd. 60 Page No. 413
71 Providing dry Trap rubble stone mansonry with headers Sq.Mt. 560.00 86.00
etc.complete. Spec. No.:
Rd. 61 Page No. 141
72 Providing rain cuts over side shoulder and making R.Mt. 5.00 5.00
arrangement for surface drainage.
Spec. No.: As directed by Engineer-in-charge
177
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
73 Reflexing the distribed guard stone in position and in R.Mt. 12.00 11.00
line with necessary excavation, back filling, ramming
etc.complete. Spec.
No.: As directed by Engineer-in-charge
74 Providing and laying shoulder drain of trap rubble of R.Mt. 110.00 43.00
0.45 x 0.45 metre section at 450 angle including hand
packing, filling voiids with sand and shingle of approved
quality and ramming etc. complete as directed.
Spec. No.: As directed by Engineer-in-charge
75 Breaking and removing the existing cement concrete Cu.Mt. 480.00 312.00
pavement to full width, depth including lean concrete,
cutting dowel bars, breaking the removed cement
concrete slab pieces into 50 to 80 mm size, spreading
the layer, watering and consolidation with power roller
etc. complete. (IInd layer not to be more than 75mm)
Spec. No.: As directed by Engineer-in-charge
178
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
78 Providing and laying CE Marked Woven Polypropylene
Geotextile of Techfab India indigenously manufactured
from black UV stabilized polypropylene tape yarn on the
prepared subgrade for Reinforcement cum separation
cum drainage & filtration application with necessary
overlaps as per drawing etc. complete. (Specification:
IRC:SP:59-2002 & MORTH Section-700)
179
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
material with LDPE, Latex, Bitumen and any other
coating will not be allowed and will not be accepted). For
reinforcement application to subgrade, unbound sub
base / base courses & soil stabilization, etc. complete
(Specification: IRC:SP:59-2002 & MORTH Section-700).
a) TFI TechGrid GeoGrid TGB-40 Sqmt 177.00 33.75
b) TFI TechGrid GeoGrid TGB-60 Sqmt 219.00 33.75
81 Providing and laying TFI TECHGRID GEOGRID TGU-40
CE Marked knitted and PVC coated Polyester Uniaxial
Geogrid (Techgrid) of Techfab India indigenously
manufactured from selected high tenacity polyester yarn
with high molecular weight (> 25000 g/mol), and low
carboxyl end group (<30 mm mol /Kg) (extruded PP
geogrid & Polyester strip & Geostrip, steel strips not
allowed & not accepted ) with granular fill as per design
prepared by technical provider of reinforced earth wall
and slope. The reinforced earth wall and slope should
have 100% coverage of 5m width knitted and PVC
coated Polyester geogrid. (Coating of
Geogrid/Reinforcing geosynthetic material with LDPE,
Latex, Bitumen and any other coating will not be allowed
and will not be accepted) for reinforced soil wall and
reinforced slope application, etc. complete
(Specification: MORTH Section-700).
180
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
a) a) TFI TGC-60 Sqmt 185.00 33.75
b) b) TFI TGC-90 Sqmt 230.00 33.75
83 Providing and inserting CE Marked Prefabricated
Vertical Drain / Band Drain (TechDrain) of Techfab
India indigenously manufactured with Polypropylene
Core and wrapped with Non-Woven Geotextile in the
very soft clay to a design depth for quick consolidation
etc. complete. (Specification: MORTH Section-700).
181
BRIDGE WORK
BR
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
1 Dismentling carefully the old structure ------------- -
------ including cutting reinforcement steel bars,
sorting out serviceable materials and stacking,
disposing off unserviceable material, upto lead of
50m etc. Complete.
182
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
ii Hard murum 118.00 51.00
iii hard murum and boulders 132.00 66.00
iv Soft rock 274.00 80.00
v Marshy soil, depth upto 3.00m 149.00 32.00
183
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
A With Concrete Mixer
i M-15 Cu.Mt. 4273.00 693.00
ii M-20 Cu.Mt. 4515.00 693.00
iii M-25 Cu.Mt. 4640.00 693.00
iv M-30 Cu.Mt. 4765.00 693.00
184
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
iii M-30 Cu.Mt. 4942.00 744.00
iv M-35 Cu.Mt. 5009.00 744.00
B with fully automatic micro processor based PLC
with SCADA enabled with reversible Drum Type
mixer.With natural sand .
i M-20 Cu.Mt. 5345.00 967.00
ii M-25 Cu.Mt. 5477.00 967.00
iii M-30 Cu.Mt. 5609.00 967.00
iv M-35 Cu.Mt. 5972.00 967.00
185
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
iv M-25 Cu.Mt. 4733.00 830.00
v M-30 Cu.Mt. 4898.00 830.00
B with fully automatic micro processor based PLC
with SCADA enabled with reversible Drum Type
mixer.With natural sand .
i M-10 Cu.Mt. 4454.00 1079.00
ii M-15 Cu.Mt. 5180.00 1079.00
iii M-20 Cu.Mt. 5510.00 1079.00
iv M-25 Cu.Mt. 5642.00 1079.00
v M-30 Cu.Mt. 5774.00 1079.00
11 Providing, fabricating & setting out Mild Steel M.T. 65424.00 6883.00
cutting edges for R.C.C well curbs as shown on
the detailed drawings. etc. complete.
Spec. No.: BR.10 Page No. 121 MoRT&H,
cl.1205
186
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
12 Providing steel anchor dowels at the base of No. 6043.00 854.00
the well including drilling holes of 60 mm dia.
with cement mortar 1:1 up to 2.5 m depth in rock,
placing the dowels in position and effectively
grouting the holes. (32mm dia. steel Rod of 4.0
m length grouted up to 2.5 m depth.).
Spec. No.: BR.15 Page No. 129
13 Providing and fixing 25mm dia. Steel anchor No. 1303.00 597.00
dowel in hard rock including drilling hole of 32
mm dia. up to 0.75 mtrs depth,. placing the
dowel in position and effectively grouting the hole
with C.M. 1:1 proportion etc. complete.
Spec. No.: BR.15 Page No. 129
As directed by Engineer in charge.
187
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
B With Fully Automatic Micro Processor based
PLC with SCADA enabled concrete Batch Mix
Plant (PAN Mixer).With crushed sand.
i M-10 Cu.Mt. 3603.00 568.00
ii M-15 Cu.Mt. 4083.00 568.00
188
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
17 Providing & laying in situ RCC including form
work Using ............ Mixer of ........Grade,. of trap/
granite/ quartzite/ gneiss metal in well steining
including, compacting by vibrating, finishing and
curing complete. (Excluding reinforcement and
including shuttering.)
Spec. No.: BR.13 Page No. 123 MoRT&H 1200,
1500 & 1700
189
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
A with fully automatic micro processor based PLC
with SCADA enabled with reversible Drum Type
mixer. With natural sand.
I In Dry Condition
19 Providing and filling in well with sand /rubble Cu.Mt. 690.00 268.00
and sand/shingle and sand including compaction
between the top and bottom plugs.
Spec. No.: BR.17 Page No. 131 MoRT&H 1210
190
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
20 Providing & laying in situ RCC including form
work Using ............ Mixer of ........Grade, of trap
/granite/ quartzite/ gneiss metal for top plug of
wells including compaction by vibration and
curing etc. complete
Spec. No.: BR.18 Page No.132 MoRT&H 1200,
1500 & 1700
A with fully automatic micro processor based PLC
with SCADA enabled with reversible Drum Type
mixer. With natural sand.
a M-15 Cu.Mt. 4506.00 984.00
b M-20 Cu.Mt. 4836.00 984.00
c M-25 Cu.Mt. 5034.00 984.00
191
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
B With Fully Automatic Micro Processor based
PLC with SCADA enabled concrete Batch Mix
Plant (PAN Mixer). With crushed sand. (RMC)
i M-20 Cu.Mt. 5373.00 585.00
ii M-25 Cu.Mt. 5506.00 585.00
iii M-30 Cu.Mt. 5638.00 585.00
iv M-35 Cu.Mt. 5902.00 585.00
192
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
Spec. No.: BR.14 Page No. 124
Well Dia. up to 5 metres R.Mt. 49665.00 24424.00
i Well Dia. above 5 metres & upto 6 metres R.Mt. 71228.00 47175.00
ii Well Dia. above 6 metres & upto 7 metres R.Mt. 97077.00 47366.00
iii Well Dia. above 7 metres & upto 8 metres R.Mt. 126472.00 61709.00
iv Well Dia. above 8 metres & upto 9 metres R.Mt. 133316.00 76052.00
v Well Dia. above 9 metres & upto 10 metres R.Mt. 140160.00 110395.00
23 Extra charges for sinking of various dia. well Cu.Mt. 1185.00 784.00
foundation in hard rock encountered during
sinking by chiselling in water.
Spec. No.: BR. 14A Page No. 124 MoRT&H
1200
193
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
25 Providing & laying in situ RCC M30 including
form work Using ............ Mixer of ........mm dia,
for bored piles with hydraulic power rig each of
load capacity as per design and of specified
diameter of as directed, placed through steel
shell sunk to the required depth through all strata
except rock, excluding provision of reinforcement
including placing concrete by tremie
arrangement compaction of concrete and
withdrawal of steel shell etc. complete. (upto
15m depth ) A/B.
Spec. No.: BR-19 Page 132, MORTH - 1100 and
1700
Note :-
1 For 15 m to 25m depth 5% extra over Basic rate
194
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
iv 1000mm dia. R.Mt. 7122.00 1419.00
v 1050mm dia. R.Mt. 7704.00 1549.00
vi 1200mm dia. R.Mt. 9714.00 2616.00
vii 1500mm dia. R.Mt. 14650.00 3151.00
Note :-
1. For 15 m to 25m depth 5% extra over Basic
rate
2. For 25 m to 35m depth 10% extra over Basic
rate
3. For 35 m to 45m depth 15% extra over Basic
rate
195
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
B With Fully Automatic Micro Processor based
PLC with SCADA enabled concrete Batch Mix
Plant (PAN Mixer). With crushed sand. (RMC)
i 600 mm dia. R.Mt. 3058.00 513.00
ii 750mm dia. R.Mt. 4387.00 798.00
iii 900mmdia. R.Mt. 5863.00 1119.00
iv 1000mm dia. R.Mt. 7185.00 1419.00
v 1050mm dia. R.Mt. 7700.00 1549.00
vi 1200mm dia. R.Mt. 9790.00 2016.00
vii 1500mm dia. R.Mt. 14745.00 3151.00
196
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
iv 1000mm dia. Rmt 8497.00 2085.00
v 1050mm dia. Rmt 9197.00 2278.00
vi 1200mm dia. Rmt 11613.00 2962.00
vii 1500mm dia. Rmt 17537.00 4633.00
Note:-
1 For 15 m to 25m depth 5% extra over Basic rate
197
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
A with fully automatic micro processor based PLC
with SCADA enabled with reversible Drum Type
mixer. With natural sand.
i 600 mm dia. Rmt 3469.00 754.70
ii 750mm dia. Rmt 4987.00 1173.10
iii 900mmdia. Rmt 6684.00 1645.30
iv 1000mm dia. Rmt 8197.00 2085.70
v 1050mm dia. Rmt 8870.00 2278.40
vi 1200mm dia. Rmt 11192.00 2962.90
vii 1500mm dia. Rmt 16879.00 4633.10
198
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
30 Providing, cutting, bending, hooking, tieing in M.T. 69451.00 6802.00
position and laying TMT / Fe 500 steel bar for
reinforcement as per detailed drawings for all
R.C.C. works.
Spec. No.: BR.28, 37 Page No. 141, 149
MORTH - 1600
31 Providing & laying in situ PCC including form
work Using ............ Mixer of ........Grade, Span
length upto 30mtr of trap/granite/quartzite/ gneiss
metal for cast in citu piers, abutment, returns,
wings etc. including provision of "V" shaped
false joints to form suitable panels on the faces
to approve design with compacting by vibrating
and curing complete, including form work
(plywood/steel) centering (excluding dewatering
by means of pump) and including bailling out
water and curing etc. complete. (upto 5.00 mt.
height) Note : add 2% for over 5.00 mt.height
increase upto 10.00 mt. and 6% height above
10.00 mt.(height for that particular structure)
Spec. No.: BR-24, Page No.-137 MoRT& H,cl.
1500, 1700 & 2200
199
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
C With Fully Automatic Micro Processor based
PLC with SCADA enabled concrete Batch Mix
Plant (PAN Mixer). With crushed sand. (RMC)
i M-20 Cu.Mt. 5135.00 740.00
ii M-25 Cu.Mt. 5267.00 740.00
iii M-30 Cu.Mt. 5399.00 740.00
200
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
A With Concrete Mixer
i M-20 Cu.Mt 5060.00 861.00
ii M-25 Cu.Mt 5225.00 861.00
iii M-30 Cu.Mt 5390.00 861.00
iv M-35 Cu.Mt 5555.00 861.00
201
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
B with fully automatic micro processor based PLC
with SCADA enabled with reversible Drum Type
mixer. With natural sand.
i M-20 Cu.Mt. 5792.00 1161.00
ii M-25 Cu.Mt. 5924.00 1161.00
iii M-30 Cu.Mt. 6056.00 1161.00
iv M-35 Cu.Mt. 6254.00 1161.00
202
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
C With Fully Automatic Micro Processor based
PLC with SCADA enabled concrete Batch Mix
Plant (PAN Mixer). With crushed sand. (RMC)
i M-20 Cu.Mt. 5584.00 975.00
ii M-25 Cu.Mt. 5716.00 975.00
iii M-30 Cu.Mt. 5848.00 975.00
iv M-35 Cu.Mt. 6046.00 975.00
36 Providing & laying in situ RCC including form
work Using ............ Mixer of ........Grade, Span
length less than 30.00mtr of trap/granite
/quartzite / gniess metal for reinforced cement
concrete block below the bearing including
necessary scaffolding, formwork, compaction by
vibrating, finishing and curing etc. complete
(excluding reinforcement)
Spec. No.: BR-27 Page No. 140
203
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
37 Providing tar paper bearing pad including fixing Sq.Mt. 131.00 63.00
etc. complete.
Spec. No.: As directed by Engineer in charge
38 Supplying, fitting and fixing in position true to line Cu.Cm. 1.85 0.35
and level neoprene elastomeric bearing
conforming to IRC:83 (Pt.-II) section IX and
clause 2005 of MORTH specifications complete
including all accessories as per drawing and
technical specifications.
Spec. No.: MORT & H – 2000 & 2005
39 Supplying, fitting and fixing in position true to line M.T. 291.00 54.00
and level cast steel rocker bearing conforming
to IRC:83 (Pt-1) section IX and clause 2003 of
MORTH specifications complete including all
accessories as per drawing and technical
specifications.
Spec. No.: MORT & H -2000,1000,2200 &f IRC
83-1982
40 Supplying, fitting and fixing in position true to line M.T. 583.00 54.00
and level forged steel roller bearing
conforming to IRC:83 (Pt-1) section IX and
clause 2003 of MORTH specifications complete
including all accessories as per drawing and
technical specifications.
Spec. No.: MORT & H – 2000 & 2200
41 Supplying, fitting and fixing in position true to line M.T. 234.00 27.00
and level sliding plate bearing with PTFE
surface sliding on stainless steel complete
including all accessories as per drawing and
technical specifications and BS:5400, section 9.1
& 9.2 (for PTFE) and clause 2004 of MORTH
specifications.
Spec. No.: MORT & H – 2000 & 2200
204
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
42 Supplying, fitting and fixing in position true to line M.T. 232.00 11.00
and level sliding plate bearing with stainless
steel plate sliding on stainless steel plate with
mild steel matrix complete including all
accessories as per drawing and technical
specifications.
Spec. No.: MORT & H – 2000 & 2200
43 Supplying, fitting and fixing in position true to line M.T. 218.00 11.00
and level POT- PTFE bearing consisting of a
metal piston supported by a disc or unreinforced
elastomer confined within a metal cylinder,
sealing rings, dust seals, PTFE surface sliding
against stainless steel mating surface, complete
assembly to be of cast steel / fabricated
structural steel, metal and elastomer elements to
be as per IRC: 83 part I & II respectively and
other parts conforming to BS:5400, section 9.1 &
9.2 and clause 2006 of MORTH Specifications
complete as per drawing and approved technical
specifications.
Spec. No.: MORT & H – 2000 & 2200
205
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
46 Back filling with A/B/ behind abutment, wing
wall and return wall complete as per drawing dn
Technical Specifications.--
Spec. No.: BR-34 Page-146, BR-43 Page-157
MORT & H 2200 &-710.1.4 of iRC 78
A Granular material Cu.Mt. 502.00 248.00
B Sandy material Cu.Mt. 857.00 248.00
47 Providing and laying of Filter media with Cu.Mt. 778.00 215.00
granular materials/ stone crushed aggregates
satisfying the - requirements laid down in clause
2504.2.2 of MORTH specifications to a thickness
of not less than 600 mm with smaller size
towards the soil and bigger size towards the wall
and provided over teh entire surface behind
abutment, wing wall and return wafl to the full
height compacted to a firm condition complete as
per drawing and technical specifications.
Spec. No.: MORT & H 2200 &-710.1.4 of iRC 78
Note:
a) Solid slab
i) 5% for height above 5.00 mtr. to 10.00 mtr.
ii) 10 % for height above 10.00 mtr.,
206
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
ii) 10% for height 5.00mtr. to 10.00mtr
iii) 15% for height above 10.00mtr.and
207
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
i M-20 Cu.Mt. 5726.00 1005.00
ii M-25 Cu.Mt. 6591.00 1005.00
iii M-30 Cu.Mt. 6901.00 1005.00
iv M35 Cu.Mt. 7006.00 1005.00
v M-40 Cu.Mt. 8327.00 1005.00
vi M-45 Cu.Mt. 8705.00 1005.00
vii M-50 Cu.Mt. 8810.00 1005.00
208
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
i M-20 Cu.Mt. 6200.00 1112.00
ii M-25 Cu.Mt. 6365.00 1112.00
iii M-30 Cu.Mt. 6621.00 1112.00
iv M-35 Cu.Mt. 6786.00 1112.00
209
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
51 Providing and fixing in position to exact profile M.T. 177072.00 7594.00
and prestressing high tensile strands of
specified ultimate strength, standard end
anchorages, cable ducts, grouting ducts after
pres-tressing and bearing plates with wedges as
per detailed drawings including necessary plant
and machinery for prestressing etc. complete. a)
For Strand
Spec. No.: As directed by Engineer in charge.
Spec. No.: BR.40 Page 155 MoRT&H-1800
210
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
56 Providing and laying of an elastomeric slab R.Mt. 23816.00 1032.00
seal expansion joint, catering to right or skew
(less then 20 deg., moderately curved with
maximum horizontal movement upto 50 mm,
complete as per approved drawing and standard
specifications to be installed by the manufacture
/ supplier or their authorized representative
ensuring compliance to the manufactures
instructions for road & bridge works)
Spec. No.: MORT & H – 2606
211
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
59 Providing & laying in situ Cement Concrete
including form work Using ............ Mixer of
........Grade, of trap /granite/ quartzite/ gneiss
metal including compacting. finishing, curing and
filling in joints with bitumen complete for wearing
course 8cm thick.
Spec. No.: BR.35 Page No. 146 and B.7, Page
No.38
A With Concrete Mixer
i M-20 Sq.Mt. 375.00 48.00
ii M-25 Sq.Mt. 387.00 48.00
iii M-30 Sq.Mt. 400.00 48.00
212
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
60 Providing and laying 12mm thick mastic Sq.Mt. 353.00 54.00
asphalt. wearing course on top of deck slab
excluding prime coat with paving grade bitumen
meeting the requirements given in table 500-29,
prepared by using mastic cooker and laid to
required level and slope after cleaning the
surface, including providing antiskid surface with
bitumen precoated fine grained hard stone
chipping of 9.5 mm nominal size at the rate of
0.005 cum per 10 Sqm and at an approximate
spacing of 10 cm center to center in both
directions, pressed into surface when the
temperature of surfaces not less than 100 deg.
C, protruding 1 mm- to 4mm over mastic surface,
all complete as per clause 516.
Spec. No.: MORT & H – 500, 2700
61 Providing vent holes 100mm dia. UPVC pipe in No. 380.00 28.00
the slab and wearing course with iron grill at the
top and galvanised iron pipe at bottom as per
drawing.
Spec. No.: BR.36 Page No. 149
62 Providing galvanised iron 100mm diameter No. 682.00 165.00
water spouts as per drawings. (length of water
spout 600mm )
Spec. No.: BR.41 Page No. 156
63 Providing & laying in situ PCC including form
work Using ............ Mixer of ........Grade, of trap
/granite /quartzite /gneiss metal for haunch
filling including compacting, curing complete.
Spec. No.: B R.33 Page No. 145
213
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
i C.C. 1: 4: 8 Cu.Mt. 3396.00 633.00
ii C.C. 1: 3: 6 Cu.Mt. 3726.00 633.00
iii C.C. 1: 2: 4 Cu.Mt. 4452.00 633.00
214
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
67 Providing and laying of Reinforced cement Cu.Mt. 8737.00 483.00
concrete in M-30 grade approach slab including
reinforcement and formwork complete with fully
automatic micro processor PLC with SCADA
enabled reversible Drum Type mixer. as per
drawing and Technical specifications.
Spec. No.: MORT & H – 1500, 1600, 1700 &
2700
215
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
69 Providing railing of mild steel angle post 2M R.Mt. 2564.00 387.00
center to center of section 75mm x 75mm x
10mm or equivalent I/ channel section of height
1.05 above bridge surface with minimum anchor
length of 30cm including hold fast of 25mm dia.
M.S. bar welded at the bottom and concreting of
1:3:6 of size 30cm x 30cm x 30cm with three
rows of 40mm B class G.I. pipe provided at 30
on center to center including scaffolding and with
one coat of anticorrosive paint and over it two
coats of oil painting, curing of concrete etc.
complete.
Spec. No.: B.R.39(b) Page No. 150
70 Providing R.C.C. railing of cast in situ R.C.C.
posts including form work Using ............ Mixer
of ........Grade,of trap/granite / gneiss metal, for
horizontal and vertical members as per detailed
drawings including reinforcement, scaffolding,
centering, formwork, compaction, finishing and
curing with watering chemical compound etc.
complete. with fully automatic micro processor
based PLC with SCADA enabled with reversible
Drum Type mixer.
Spec. No.: BR.39 Page No. 152
A With Concrete (c) Mixer
i M-20 R.Mt. 2120.00 578.00
ii M-25 R.Mt. 2225.00 578.00
B With fully automatic micro processor based PLC
with SCADA enabled with reversible Drum Type
mixer. With natural sand.
i M-20 R.Mt. 2360.00 632.00
ii M-25 R.Mt. 2465.00 632.00
C With Fully Automatic Micro Processor based
PLC with SCADA enabled concrete Batch Mix
Plant (PAN Mixer). With crushed sand. (RMC)
i M-20 R.Mt. 2240.00 632.00
ii M-25 R.Mt. 2345.00 632.00
216
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
71 Providing and fixing 25 mm thick marble tablet Sq.Mt. 9020.00 2550.00
of size and description as per detailed drawings
inclduing engraving the description,filling the
lead, moulded marble 1:2 cement mortar border
etc.complete.
Spec. No.: BR-42 Page No. 157
72 Providing and applying anticorrisive treatment M.T. 8920.00 3165.00
for MS & TOR steel reinforcement as per cement
polymer composite coating (CPCC) method
developed by CECRI including cleaning the bar
by means of any established mechanical or
manual method for removing the rust and
deletious matter, applying rapid setting primer
and cement polymer sealing coat of approved
and licensed by CECRI including redoing the
process if damaged occur during handling,
stacking etc. complete as directed by the
Engineer in charge. (with prior approval of S.E. is
essential.)
Spec. No.: As directed by Engineer-in-charge
217
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
75 Providing and applying approved quality coal tar Sq.Mt. 325.00 70.00
epoxy paint in three coats for surface of well,
pier abutment between L.T.L. to 0.90 metre
above H.F.L. including cleaning surface,
scaffolding etc. complete
Spec. No.: MORT&H 1600
76 Painting on concrete surface :-Providing and Sq.Mt. 124.00 16.00
applying 2 coat of water based cement paint to
un plastered concrete surface after cleaning the
surface of dirt, dust, oil, grease, efflorescence
and applying plaint of 1 litre for 2 Sq.m.)
Spec. No.: MORT & H 2800,
218
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
79 Providing and applying Polymer synthetic Sq.Mt. 660.00 165.00
elastomeric coating cum paint, ready to use for
bridge structure in saline as to avoid salt
penitration from marine environmet & U.V effects
of sunrays, fungus developments and to protect
the reinforcement from marine atmoshpere
effects in three coats including scaffolding, sand
blasting, cleaing the surface of concrete,
brushing steel reinforcement and applying
polymer coating with Primer, First coat and
Second coat at an interval of 24 hours of
approved shade and colour.( But not to applied
on oil, Grease, Tar & Moisture of surface Note:-
Prior approval of S.E. is required.)
Spec. No.: As directed by Engineer-in-charge
219
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
82 Providing and injecting epoxy grout including No. 1288.00 167.00
structuring of cracks in the body of slab girder,
fixing it inlet to be arrange-ment including cost of
materials, machinery required for the work labour
charges etc. Note : 2Kg. of grout is consider per
hole.
Spec. No.: As directed by Engineer in charge.
83 Repairing of honey combed area, spilling area Sq.Mt. 395.00 31.00
by chipping out the damaged spalled or honey
combed portion of concrete up to behind rebars
with rusting, cleaning of all rust, scale and loose
materials scaffolding compressed air, machinery
etc. complete. (Note.: Item includes use of air
compressor, chipping machine and scaffolding
for height of 8 to 10 meters.)
Spec. No.: As directed by Engineer in charge.
86 Providing and laying M-35 grade c.c. for R.C.C. Cu.Mt. 5724.00 1325.00
jacketing around the piers etc. complete.
220
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
(Note : This item includes jacketing to piers of
existing bridge. This item includes scaffolding for
height of 8 to 10 meters.)
Spec. No.: As directed by Engineer in charge.
87 Providing and laying boulders apron laid Cu.Mt. 847.00 212.00
without wire crates on river bed for protection
against scour with stone boulders weighing not
less than 40 kg each complete as per drawing
and Technical specifications.
Spec. No.: MORT & H-2500
88 (Providing and laying of boulder apron laid in Cu.Mt. 1579.00 269.00
wire crates made with 4 mm dia GL wire
conforming to IS:2801 & IS:4828 in 100 mm X
100 mm mesh(weaved diagonally ) including
10% extra for laps and joints laid with stone
boulder weighting not less than 40 kg each.)
Spec. No.: MORT & H-2500
89 Providing and laying of apron with cement Cu.Mt. 4526.00 591.00
concrete blocks of size 0.5 X 0.5 X 0.5 m cast
in-situ and made with nominal mix of M-15 grade
cement concrete with a minimum cement content
of 250kg/ cum . as per IRC:21-2000.)
Spec. No.: MORT & H-2500
221
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
92 Providing and laying Filter material underneath Cu.Mt. 1030.00 430.00
pitching in slopes complete as per drawing and
Technical specifications.
Spec. No.: MORT & H-2500
93 Laying of a geotextile filter between pitching and Sq.Mt. 856.00 109.00
embankment slopes on with pitching is laid to
prevent escape of the embankment material
through the voids of the stone pitching / cement
concrete blocks as well as to allow free
movement of water without creating any uplift
head on the pitching.)
Spec. No.: MORT & H – 700
94 Providing and laying Flooring of Rubble stone Cu.Mt. 4045.00 1021.00
laid in cement mortar 1:3 complete as per
drawing and Technical specifications laid over
cement concrete bedding.
Spec. No.: MORT & H –2500
95 Providing and laying Flooring of Cement Cu.Mt. 5637.00 773.00
Concrete blocks Grade M-15 complete as per
drawing and Technical specifications laid over
cement concrete bedding.--
Spec. No.: MORT & H –2500
96 Construction of dry rubble Flooring at cross Cu.Mt. 1558.00 856.00
drainage works.
Spec. No.: MORT & H – 2500
97 Providing and construction of a gabion Cu.Mt. 1582.00 91.00
structures of retaining earth with segments of
wire crates of size 7 m X3 mX 0.6 m each
divided into 1.5 m compartments by cross
netting, made form 4 mm galvansed steel wire @
32kg per 10 sqm having minimum tensile
strength of 300 Mpa conforming to IS :280 and
222
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
galvanizing coating conforming to IS:4826 woven
into mesh with double twist, mesh size not
exceeding 100X 100 mm, filled with boulders
with least dimension of 200 mm, all loose ends to
be tied with 4 mm galvanized steel wire )
Spec. No.: MORT & H-2503.3
223
ITEM Final Rate (2015-16)
NO. Description Unit Completed Labour
1 2 3 4 5
101 RE WALL (Reinforced Earth Wall) Providing and
Laying CE marked Knitted and PVC coated
Polyester Uniaxial Geogrid (Techgrid) of Techfab
India indegeniously manufactured from selected
high tenacity polyester yarn with high molecular
weight (> 25000 g/mol), and low carboxyl end
group (<30mmol/kg) for Reinforced soil wall of
height .........mtr (extruded PP geogrids &
Polyester strips & Geostrips, Steel Strips not
allowed & not accepted) with granular fill of PHi-
32 degree (design is to be carried out in
accordance with BS-8006 / FHWA) with concrete
block by M-35 as facia, casting & erection of
blocks with Techgrid, providing & laying levelling
pad by M-15, providing and laying coping beam
by M-35, providing and laying 300mm thick
filtermedia etc. completed as per necessary
drawing and instruction of Engineer-in-charge.
224
C. D. WORKS
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
1 Providing & laying in situ cement concrete of.........
.grade proportion with trap/ granite/ quartzite/
gneiss metal in foundation including necessary
form work compacting and curing etc. complete.
with reversible Drum Type mixer with SCADA.
With natural sand .
Spec.No.CD-1,P-317 / 2012
a C.C. 1:4:8 Cu.Mt. 3490.00 583.00
b C.C. 1:3:6 Cu.Mt. 3629.00 544.00
2 Providing uncoursed rubble trap/ quartzite/ Cu.Mt. 3307.00 1109.00
gneiss stone masonary in cement mortar 1:5 for
piers, abutments, wings, returns, headwalls,
parapet etc. including striking joints of the non
exposed faces and pointing the exposed faces
with cement mortar 1:3 including scaffolding and
watering masonary complete including bailing out
of water.
Spec.No.CD-4,P-319 / 2012
3 Providing & laying in situ cement concrete of
...........grade of trap /granite /quartzite /gneiss
metal for cast in citu head walls for causeway &
C. D. Works with compaction by vibrating & curing
complete including form work centering
(excluding dewatering by means of pump and
including bailling out water).
Spec. No. BR-24 Page No.137 / 2012
A With SCADA with fully automatic micro processor
based PLC with SCADA enabled reversible Drum
Type mixer
i PCC M-15 Wihth SCADA Cu.Mt. 4319.00 523.00
ii PCC M-20 with SCADA Cu.Mt. 4515.00 551.00
B Without SCADA with concrete mixer with hopper
225
C. D. WORKS
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
4 Providing and laying in situ M.15 cement concrete Cu.Mt. 4082.00 743.00
of trap /granite /quartzite /gneiss metal including
compacting, finishing, curing and completewith
fully automatic micro processor based PLC with
SCADA enabled reversible Drum Type mixer for
approach slab (excluding reinforcement.)
226
C. D. WORKS
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
8 Providing approved quality of trap/ granite/ Sq.Mt. 1526.00 584.00
quartzite/ gneiss khandki stone paving
20.50cm.thick in 1:3 cement mortar over a
bedding of 15cm.thick cement concrete of 1:4:8
proportion with trap/ granite/ quartzite/ gneiss
metal including pointing with cement motar 1:3
and watering etc. complete.
Spec.No.CD-3,P-318 / 2012
9 Providing selected hard murum filling including Cu.Mt. 294.00 74.00
laying in layers of 15cm.to 20cm. watering and
compacting complete.
Spec.No.CD-8,P-321 / 2012
10 Providing Precast M-25 R.C.C.slabs over the Cu.Mt. 8908.00 2520.00
spans of cross drainge work as per drawings
including TMT bar reinforcement, conveyance,
fixing in cement mortar 1:3 and curing, finishing
etc. complete.
Spec.No.CD-12,P-166 Edition 1981
11 Providing & laying in situ cement concrete of Cu.Mt. 3490.00 640.00
1:4:8 of trap metal for haunch filling including
formworks compacting curing & scaffolding etc.
complete
Spec.No.CD-7,P-321 / 2012
12 Providing & fixing stream lined R.C.C. guard No. 333.00 66.00
stone including (1:2:4) c.c and mild steel bar
reinforcement complete.
Spec.No.CD-12,P-322 / 2012
13 Providing and fixing M-15 R.C.C.Guard stone of No. 401.00 90.00
20 x 20 x 75 cms including fixing in ground and
white washing etc. Complete.
Spec.No.CD-12,P-322 / 2012
14 Laying cement concrete pipe of IS 458-1988 Np-2
for V.R.&O.D.R.Class in proper line level & slope
including providing fixing collars in cement motar
1:2 etc.complete.
Spec.No.CD-5,P319 / 2012
227
C. D. WORKS
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
a) 450mm diameter (for irrigation purpose only) R.Mt. 330.00 237.00
b) 600mm diameter (for irrigation purpose only) R.Mt. 409.00 292.00
c) 750mm diameter R.Mt. 524.00 368.00
d) 900mm diameter R.Mt. 586.00 416.00
e) 1000mm diameter R.Mt. 684.00 489.00
f) 1200mm diameter R.Mt. 727.00 530.00
15 Laying cement concrete pipe of IS 458-1988 Np-
3 for M.D.R.&S.H Class in proper line level &
slope including providing fixing collars in cement
motar 1:2 etc.complete. Diameter 900 mm
Spec.No.CD-5,P319 / 2012
a 900mm diameter R.Mt. 697.00 515.00
b 1000mm diameter R.Mt. 814.00 604.00
c 1200mm diameter R.Mt. 865.00 644.00
16 Laying cement concrete pipe of IS 458-1988 Np-
4 for MSH&NH. Class in proper line level & slope
including providing fixing collars in cement motar
1:2 etc.complete. Diameter 900 mm
Spec.No.CD-5,P319 / 2012
a 900mm diameter R.Mt. 697.00 515.00
b 1000mm diameter R.Mt. 814.00 604.00
c 1200mm diameter R.Mt. 865.00 644.00
17 Providing and fixing in cement mortar 1:2, marble No. 456.00 365.00
plate 30cm. x 20cm. showing the No. of Cross
Drainage work and the direction of flow by arrow
including cutting border line, figures, letters, signs
and painting etc. complete.
Spec.No.CD-10,P-322 / 2012
228
BORING
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
1 Taking trial bores for detailed investigations with
75mm/100mm/150 diameter boring in overburden,
hard murum, boulders including all materials such as
temporary casing pipes & accessories, grease,steel
balls,drill rods,core lifter, reaming shells,core bar
229
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
3 Taking trial bores for detailed investigations in
following catagory strat including all materials such as
temporary casing pipes & accessories, grease,steel
balls,diamonds bits HX/NX/BX/AX type as per
requirements,drill rods, core lifter,reaming shells, core
barrels impregnated daimond bits,air houses,water
swivels etc.& other such materials as required
including conveying such materials and machinery to
site works,collecting & preserving the loose samples in
a glass or plastic jar collection of water samples wash
samples core samples as directed , preserving
samples in plastic /glass jars,serially numering cores
samples, preseserving core samples properly in core
boxes at site of work, preparation and submission of
bore logs with soils & rocks classification, conveying
samples to headquarter of concerned office as
directed etc complete.
In Other rock
a) With rotary diamond drilling machine by using HX bit R.M. 3908.00 116.00
(Core size 86 mm)
b) With rotary diamond drilling machine by using NX bit R.M. 2454.00 116.00
(Core size 54 mm)
4 Taking trial bores by hand augar through over burden R.M. 511.00 488.00
such as soil and soft murum upto hard strata.
Spec.
5 Providing Tuntappa core boxes of jungle wood of size No. 2780.00 547.00
1.25 x 0.55 x 0.15 metre for preserving core samples
with all fixtures and fastening handles locking
arrangements etc. complete.
Spec.
6 Providing and maintaining a Temporary platform as
required 100 Sq.ft. size for erecting the boring
machine for taking trial bore in the nalla / small river
bed in standing water -a/b/c- including all materials
etc.complete.
Spec.
a) For depth up to 1.00 Meter. No. 12763.00 3073.00
b) For depth of 1.00 to 2.00 Meter. No. 22940.00 6147.00
c) For depth 2.00 Meter. And above No. 29990.00 5735.00
230
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
7 Providing and maintaining temporary floating
platform as required 10 Sq.mtr. size with country
crafts and teak wood platform and/anchor's for
erecting boring plant in standing and flowing water -
a/b/c-including all material, labours etc. complete.
Spec.
a) For depth above 2.00 Meter. No. 92257.00 5309.00
b) For depth of 5.00 to 10.00 Meter. No. 96768.00 5309.00
c) For depth above 10.00 Meter. No. 133670.00 5309.00
Note: The rate of Boaring item No.6&7( as given
above ) is proposed for total working of platform for 10
days, if more work, the rate of this item should be
worked out on the basis of rates abstract for item
No.7(a).
8 Shifting boring platform as required (100 Sq.Ft. size)
with all components and reinstalling at directed
places,including all charges of shifting etc.complete.
Spec. No. 3555.00 3465.00
9 Conducting standard pentration test on soil, sand by
split spoon sample for--a/b/c--diameter bore hole
including labour & material etc. complete.(Equipment
and materials is to be supplied by Department free of
cost).
Spec.
a) 75mm No. 300.00 233.00
b) 100mm No. 396.00 312.00
c) 150mm No. 596.00 466.00
10 Carrying out various tests on sub soil & rock samples
as directed etc. complete.
Spec.
1) Natural Moisture content per test 244.00
2) Wet and Dry Density per test 244.00
3) Lab Vane Shear Test per test 484.00
4) Tor Vane per test 484.00
5) Pocket Soil Penetrometer per test 363.00
6) Sieve Analysis per test 484.00
7) Hydrometer per test 484.00
231
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
8) Liquid and Plastic Limit per test 363.00
9) Shrinkaage Limit per test 363.00
10) Specific Gravity per test 484.00
11) Relative Density per test 484.00
12) Unconfined Compressive Strength per test 1089.00
TRIAXIAL
i) Unconsilated Undrained per test 1452.00
ii) Consolited Undrained per test 1562.00
iii) Consolited Drained per test 1694.00
iv) Consilidation per test 1562.00
v) Direct Shear Test per test 1391.50
Proctor Compaction Test
i) Standard Proctor Compaction Test per test 1331.00
ii) Modified Proctor Compaction Test per test 1210.00
iii) California Bearing Ratio (Lab CBR) per test 1562.00
Permeability
i) Constant Head Method per test 1089.00
ii) Falling Head Method per test 1089.00
iii) Free Swell Index per test 484.00
iv) Swelling Pressure per test 1562.00
11 Chemical Analysis of Soil
i) pH Value per test 484.00
ii) Chloride (cl) per test
iii) Sulphate (SO3) per test
12 Chemical Analysis of Water
i) pH Value per test 484.00
ii) Chloride (cl) per test 605.00
iii) Sulphate (SO3) per test 605.00
13 Test on Rock Samples
i) Unconfined Compressive Strength per test 1562.00
ii) Dry Density per test 484.00
iii) Porosity per test 484.00
iv) Water Absorption per test 484.00
v) Specific Gravity per test 484.00
vi) Modulus of Elasticity per test 4840.00
vii) Point Load Index per test 1452.00
viii) Brazilian Index per test 1452.00
232
Survey Work (Dept. Agencies) Survey-D
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
1 Ground reconnaissance survey of road alignment in Km. 721.00
plain area including fixing reference pegs wherever
necessary and with th help of simple survey instruments .
233
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
6 Detailed/final location survey of road alignment with Km. 3044.00
chain and compass, ghat tracer, levels, theodolite and
other essential instrument including staking of final centre
line, locating curves, establishing Bench marks and taking
longitudinal section, cross section, fly levelling
etc.complete (in hilly and inaccessible area)
Spec. - As directed by Engineer-In-Charge.
7 Detailed survey along existing earth work including taking Km. 2790.00
longitudinal section, cross section, fixing, Bench Marks,
chaining, fixing pegs and closing the survey with fly levels
etc.complete.
Spec. - As directed by Engineer-In-Charge.
8 Fixing chainage, appex stones and mark stones of trap No. 3217.00 1108.00
stone in cement concrete 1:3:6 of size 45 x 45 x 60
cm.along the alignment, 5 chainage stones and 6 appex stones
etc. complete.
Spec. - As directed by Engineer-In-Charge.
9 Taking trial pit 1.0 x 1.0 x 1.5 mtr.at 200 metre interval No. 263.00 263.00
and minimum 3 numbers for small stream in earth soil of
all types, sand, gravel, soft murum etc. complete.
Spec. - As directed by Engineer-In-Charge.
10 Taking trial pit 1.0 x 1.0 x 1.5 mtr.at 200 metre interval No. 263.00 263.00
and minimum 3 numbers for small stream in hard murum
and boulders etc.complete.
Spec. - As directed by Engineer-In-Charge.
11 Providing and fixing wooden pegs for road alignment Km. 1049.00 224.00
survey including using chunam and coir string etc.
complete.
Spec. - As directed by Engineer-In-Charge.
12 Taking purely fly level to carry out kilometre Bench Mark, Km. 196.00 134.00
etc.complete
Spec. - As directed by Engineer-In-Charge.
234
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
13 Providing and fixing chaniage, appexes, Bench Mark No. 603.00 96.00
stone of size 17 x 22 x 60 cm.in cement concrete 1:4:8
block of size 45 x 45 x 60 cm. including excavation,
conveyance etc.complete.
Spec. - As directed by Engineer-In-Charge.
14 Painting and lettering charges on appex on Bench mark No. 248.00 46.00
stone. (Labour charges only)
Spec. - As directed by Engineer-In-Charge.
15 Survey of catchment area of stream upto 100 Acres by No. 457.00 438.00
visual inspection with using of chain and compass
etc.complete. (Approximate 100 Acres as per village map)
(average three streams per kilometer)
Spec. - As directed by Engineer-In-Charge.
16 Traverse survey of stream having catchment area above No. 1350.00 1125.00
100 Acres to 1 square mile with chain and compass
etc.complete.
Spec. - As directed by Engineer-In-Charge.
18 Reconnaissance survey for fixing major bridge site No. 1522.00 1480.00
including chain and compass and other instruments as
necessary, fixing reference pegs etc.complete.
Spec. - As directed by Engineer-In-Charge.
235
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
20 Complete survey of major stream for additional site No. 12098.00 11080.00
including taking necessary chainage, Longitudinal section,
cross section, closing survey at the ends of days work and
contouring work for the same bridge site etc.complete
21 Carrying out the contour survey of the stream for 1 Sq.Km. 29041.00 26591.00
square kilometre area.
Spec. - As directed by Engineer-In-Charge.
236
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
27 Detailed survey in creek including its approaches w ith Km. 5213.00 3102.00
chain and compass survey along the bridge
alignment and levelling (without cross section)
including rent of country crafts etc.complete.
Spec. - As directed by Engineer-In-Charge.
28 Measuring velocity of creek at 3 section (1 centre and No. 4197.00 1995.00
others on both banks) at an interval of two hours (four times in
day) by sink floats etc. including rent of country crafts
etc.complete.
Spec. - As directed by Engineer-In-Charge.
237
Survey Work (Private Agencies) SURVEY-P
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
1 Reconnaissance survey including study of survey
sheets, maps etc. for alignment including three
dimensional of apexes,chain and compass or cross
staff survey,fixing pegs, fixing apex stones of size 0.15
x 0.15 x 0.60 cm in 1:2:4 cement concrete at every
apex point and 200 m. and preparation of alignment
plan with all types of compliance, if required from
department etc. complete.
a) excluding fixing of apex stone. Km 8382.00
b) including fixing of apex stone. Km 9842.00
2 Procurement of Village map/Forest map/Land plan No. 150.00
from Forest/Revenue authority for prepartation of land
plan record,including necessary payment for the plans
and other documents as required for this
survey,plotting and demarcation works etc.complete.
As directed by Engineer-In-Charge.
3 Prepartion of land plans of road ( New alignment) Km 7418.00
with fixing boundaries on both sides of centre line of
Road / Existing road up to road boundary, including
carrying out detailed plain table survey along the
centre line of the road, showing details of permanent /
semi-permanent structures, trees, telefone-lines, pipe-
lines, field-bunds, cross-roads upto 100m or as
directed,plotting work of surveyed area etc. complete.
As directed by Engineer-In-Charge.
4 Preparation of land plans (Tracing) on polyester Job 360.00
tracing film of approved make 60/65 micron on one
side matt,including taking out prints and binding the
same in Road wise etc.complete.
As directed by Engineer-In-Charge.
5 Scanning and digitizing the surveyed plane table on Km 2700.00
Autocad14 & preparing computor disk.
As directed By Engineer-In-Charge.
6 Providing '7' copies of computor printouts of plans duly Km 4708.00
bound in the form of booklet.
As directed By Engineer-In-Charge.
238
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
7 Preparation of villagewise Land acquisition Km 5533.00
proposals in five sets as required by Revenue
Authorities (SLAO) including procurement of
necessary 7/12 extracts, preparation of Land
schedule, tracing out of village maps (at the same
scale of revenue map), and taking out ammonia prints
(5copies), colouring the same, showing the alignment
on village map, taking out 5xerox copies of
questionnaries schedule of land to be aquired
respective 7/12 extracts & binding in booklets (5Nos.)
etc. complete.
As directed By Engineer-In-Charge.
8 Providing and fixing boundary stone (R.C.C.M-15)of No. 400.00
standard size 15cm.dia.on top, 25cm dia. @ bottom
and 90 cm in length with 4 bars of 6 mm dia.&5
stirrups as per IRC:25-1967,including oil painting with
two coats in white colour to visible portion on all faces
and lettering “R.B.” with black oil paint etc. complete.
239
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
11 Carrying out survey for Minor Bridge including taking
L-section of existing road, two define cross sections
for, one at U/S, second at D/S, one vergin cross
section at alternate proposed site, taking L-section of
stream upto sufficient length with chain and compass,
taking three trial pits of size 2.00 x 2.00 x 3.00 M. and
collecting samples of bed materials from trial pit for
ascertaining the silt factor unit test etc.complete.
As directed by Engineer-In-Charge.
a) excluding taking trial pit. Job 24219.00
b) including taking trial pit. job 29054.00
12 Carrying out Contour survey of stream on U/S and
D/S of proposed bridge site,including chain and
compass survey, taking levels at every 30 x 30 metre,
preparing contour map and supplying ammonia prints
in 5 sets etc.complete
As directed by Engineer-In-Charge.
a) excluding chain and compass survey. Sq.Km 25016.00
b) including chain and compass survey. Sq.Km 29334.00
13 Preparing plans and estimates of minor bridge with Job 6137.00
the help of approved detailed survey data given by the
competent authority, including typing in 5 copies,
ammonia prints, site plan, other drawings with
colouring of plans, proper filling, indexing and and
paging,with all types of compliacne, if required from
department etc.complete.
As directed by Engineer-In-Charge.
14 Carrying out detailed survey of major bridge
including taking out L-section of existing road, two
define cross sections for,one at U/S and second at
D/S, one vergin cross section at alternate proposed
site, L-section of stream upto sufficient lengths with
chain and compass, taking five trial pits, three in bed
and two on banks of size 2.00 x 2.00 x 3.00
m,collecting samples from trial pit, sending samples to
Government approved laboratories (testing charges to
he borne by agency) for ascertaining the silt factor,
carrying out unit test & specific gravity,
240
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
preparation of detailed survey data and submission of
the project fully typed colouring of the ammonia prints,
site plan and other drawings,with all types of
compliance if required from department etc.complete.
As directed by Engineer-In-Charge.
a) excluding taking trial pit. Job 35945.00
b) including taking trial pit. Job 47252.00
15 Preparing detailed plans and estimate of major Job 6661.00
bridge in 5 copies typed,on the basis of the approved
line diagram and technical note from the competent
authority including ammonia prints of site plan,other
drawings with colouring of plans,proper filling, indexing
and paging,with all types of compliance if required
from department etc.complete
As directed by Engineer-In-Charge.
16 Carrying out detailed survey of Raised cause way
including taking L-section of existing road, taking two
define cross sections for, one at vergin, one at
alternate proposed site,taking L-section of stream upto
sufficient length with chain and compass, taking two
trial pits of size 2.00 x 2.00 x 3.00 m.,collecting sample
from trial pits sending samples to Government
approved laboratory (testing charges to he borne by
agency) for ascertaining the silt factor,carrying out unit
test & specific gravity, preparation of detailed survey
data and submission of the project fully typed
copies,colouring of the ammonia prints, site plan and
other drawings with all types of compliance if required
from department etc.complete.
As directed by Engineer-In-Charge.
a) excluding taking trial pit. Job 13750.00
b) including taking trial pit. Job 16854.00
241
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
17 Preparing detailed plans and estimate of Raised Job 5521.00
causeway in 5 copies duly typed,on the basis of the
approved detailed survey data given by competent
authority including ammonia prints of site plan and
other drawings, colouring of plans, proper filling,
indexing and paging with all types of compliance if
required from department etc. complete.
As directed by Engineer-In-Charge.
18 Conversion of Taluka map and cutting in to standard Tal. 8190.00
A size sheet for scanning,scanning of A size sheets of
maps by sending to Advanced Scanning center at
Mumbai with courier,editing of scanned images
including Scaling,Positioning and Speckling,raster to
Vector conversion of images using RTOV legal
softwares,stitching of converted images by way of
GCP into single Vector drawing AUTOCAD vcr.12
legal software, Layering of drawing for colour
separation purpose organizing data by way to logical
grouping, assigning different colours of National
Highway, State Highway, Major district road
etc.,assigning different line types for existing and
proposed works,assigning different line types for
existing and proposed works,assigning different line
widths for villages, boundaries, forest areas
etc.,blocking the different roads with the symbols for
National Highway, State Highway, Main District Road
etc.,instating symbols for villages etc.,inserting text in
English at proper locations for villages names, roads
and important places etc.,Trial plot for making
corrections on A1/A2 size, multiple colours plotter in
foot scale on white papers making appropriate
corrections in vector drawing and updating all
imformation,plotting of drawing with high quality colour
plotter as a final out put etc complete.
As directed by Engineer-In-Charge.
242
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
19 Preparing District map including stitching of all Job 3026.00
village maps by way of CCP in to single sector
drawing using AUTOCAD vcr.12 legal software, Trial
plot for making corrections on A1/A2 size multi colour
plotter in foot scale on white paper,ploting drawing
drawing by high quality colour plotter as a final output
etc.complete
As directed by Engineer-In-Charge.
20 For text of villages in deonagari font extra work would Dist. 4036.00
be follows including inserting text in deonagari font at
proper locations for village names, roads and
important place etc.,Trial plot for making corrections
on A1/A2 size multi colour plotter in foot scale on white
paper,ploting of drawing on high quality colour plotter
as final output etc.complete
As directed by Engineer-In-Charge.
As directed by Engineer-In-Charge.
243
ITEM Final Rate (2015-16)
NO. Description Unit
Completed Labour
1 2 3 4 5
22 Total station survey of existing compound area Sqm. 6.00 -
showing existing plot boundry, structure, electric poll,
manhole, chamber, trees location details adjoining
roads etc.
244
VIDEOGRAPHY
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
Cassette 2152.00
Providing & carrying out video cassettee hour
hour.
shooting of roads,bridges,buildings,other structures
and programmes, including preliminary survey, still
shots moving shooting, transportation of all
1
equipments, persons required for shooting, lighting
arrangement as may be necessary, editing, mixing,
titling, lettering, sounding including cost of two coloured
cassette (C.D) of approved quality etc. complete
As Directed by the Engineer-In-Charge
2 Preparing and carrying out video shooting of roads,
bridges, buildings, other structures and progremmes,
including hiring of vehicles, equipment for video
shooting, titling, lighting, mixing, lettering, editing,
including cost of two colour cassettes(C.D)of approved
make and quality etc. complete.
245
ITEM Final Rate (2015-16)
Description Unit
NO. Completed Labour
1 2 3 4 5
i) AO ( 1165 X 817mm ) 1 each 768.00
ii) A1 ( 817 X 570mm ) 1 each 615.00
iii) A2 ( 570 X 396mm ) 1 each 537.00
iv) A3 ( 396 X 275mm ) 1 each 461.00
v) A4 ( 285 X 196mm ) 1 each 307.00
246
Transportation charges over distance 0.05 to 200.00 kms. Including loading & unloading charges.
STATEMENT 'C' FOR THE YEAR 2015-2016
Lead Avrg Factor No.of Kms Qty. Cost Qty. Cost Cost of Hire Total 10% Gross Cost Lead
in Speed trips N= Done of of of of 6 charges Cost overhead Total per trip in
kms km/Hr. (8/(F* Diesel Diesel Oil Oil Mazdoor of Truck chrges (14/4) kms
L S F (L/S))+1)) FNL+6 in Ltrs Rs. in Ltrs Rs. Rs . Rs. Rs. Rs. Rs. Rs. L
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
0.50 15 2 7.5 13.5 3.38 192.1 0.1 26.8 2538.00 3200 5956.85 595.69 6552.54 873.67 0.50
1.00 16 2 7.11 20.22 5.06 287.5 0.14 37.52 2538.00 3200 6063.03 606.3 6669.33 938.02 1.00
1.50 16.5 2 6.77 26.31 6.58 373.9 0.19 50.92 2538.00 3200 6162.80 616.28 6779.08 1001.34 1.50
2.00 17 2 6.48 31.92 7.98 453.4 0.23 61.64 2538.00 3200 6253.06 625.31 6878.37 1061.48 2.00
2.50 17.5 2 6.22 37.1 9.28 527.3 0.26 69.68 2538.00 3200 6334.97 633.5 6968.47 1120.33 2.50
3.00 17.5 2 5.96 41.76 10.44 593.2 0.3 80.4 2538.00 3200 6411.60 641.16 7052.76 1183.35 3.00
3.50 18 2 5.76 46.32 11.58 658 0.33 88.44 2538.00 3200 6484.42 648.44 7132.86 1238.34 3.50
4.00 18 2 5.54 50.32 12.58 714.8 0.36 96.48 2538.00 3200 6549.28 654.93 7204.21 1300.40 4.00
4.50 18.5 2 5.38 54.42 13.61 773.3 0.39 104.5 2538.00 3200 6615.84 661.58 7277.42 1352.68 4.50
5.00 18.5 2 5.19 57.9 14.48 822.8 0.41 109.9 2538.00 3200 6670.63 667.06 7337.69 1413.81 5.00
6.00 19 2 4.9 64.8 16.2 920.5 0.46 123.3 2538.00 3200 6781.76 678.18 7459.94 1522.44 6.00
247
7.00 19 2 4.61 70.54 17.64 1002 0.5 134 2538.00 3200 6874.30 687.43 7561.73 1640.29 7.00
8.00 19.5 2 4.39 76.24 19.06 1083 0.54 144.7 2538.00 3200 6965.71 696.57 7662.28 1745.39 8.00
9.00 19.5 2 4.16 80.88 20.22 1149 0.58 155.4 2538.00 3200 7042.34 704.23 7746.57 1862.16 9.00
10.00 20 2 4 86 21.5 1222 0.61 163.5 2538.00 3200 7123.11 712.31 7835.42 1958.86 10.00
15.00 20 2 3.2 102 25.5 1449 0.82 219.8 2538.00 3200 7406.67 740.67 8147.34 2546.04 15.00
20.00 25 2 3.08 129.2 32.3 1835 0.92 246.6 2538.00 3200 7819.85 781.98 8601.83 2792.80 20.00
25.00 25 2 2.67 139.5 34.88 1982 1 268 2538.00 3200 7987.88 798.79 8786.67 3290.89 25.00
30.00 30 2 2.67 166.2 41.55 2361 1.05 281.4 2538.00 3200 8380.27 838.03 9218.30 3452.55 30.00
35.00 30 2 2.4 174 43.5 2472 1.24 332.3 2538.00 3200 8541.99 854.2 9396.19 3915.08 35.00
40.00 35 2 2.43 200.4 50.1 2847 1.29 345.7 2538.00 3200 8930.40 893.04 9823.44 4042.57 40.00
45.00 35 2 2.24 207.6 51.9 2949 1.33 356.4 2538.00 3200 9043.40 904.34 9947.74 4440.95 45.00
50.00 35 2 2.07 213 53.25 3026 1.36 364.5 2538.00 3200 9128.15 912.81 10040.96 4850.70 50.00
60.00 35 2 1.81 223.2 55.8 3171 1.41 377.9 2538.00 3200 9286.44 928.64 10215.08 5643.69 60.00
70.00 40 2 1.78 255.2 63.8 3625 1.45 388.6 2538.00 3200 9751.72 975.17 10726.89 6026.34 70.00
80.00 40 2 1.6 262 65.5 3722 1.49 399.3 2538.00 3200 9859.03 985.9 10844.93 6778.08 80.00
Lead Avrg Factor No.of Kms Qty. Cost Qty. Cost Cost of Hire Total 10% Gross Cost Lead
in Speed trips N= Done of of of of 6 charges Cost overhead Total per trip in
kms km/Hr. (8/(F* Diesel Diesel Oil Oil Mazdoor of Truck chrges (14/4) kms
L S F (L/S))+1)) FNL+6 in Ltrs Rs. in Ltrs Rs. Rs . Rs. Rs. Rs. Rs. Rs. L
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
90.00 40 2 1.45 267 66.75 3793 1.51 404.7 2538.00 3200 9935.42 993.54 10928.96 7537.21 90.00
100.00 40 2 1.33 272 68 3864 1.53 410 2538.00 3200 10011.80 1001.18 11012.98 8280.44 100.00
125.00 40 2 1.1 281 70.25 3992 2.01 538.7 2538.00 3200 10268.29 1026.83 11295.12 10268.29 125.00
150.00 40 2 0.94 288 72 4091 2.06 552.1 2538.00 3200 10381.12 1038.11 11419.23 12148.12 150.00
175.00 40 2 0.82 293 73.25 4162 2.09 560.1 2538.00 3200 10460.19 1046.02 11506.21 14031.96 175.00
200.00 40 2 0.73 298 74.5 4233 2.12 568.2 2538.00 3200 10539.25 1053.93 11593.18 15881.07 200.00
248
Statement 'C1' ,Transportation Charges for Different Material
FOR THE YEAR 2015-2016
Lead in Cost per Earth, Sand, Hand Rubble Steel, Bulk Asphalt in Bricks Concrete Roofing All Types R.C.C.Hume pipe for Hot Mix
KMS Trip Murum, crushed brokan Excavated Cement, Bituman Drum block & Tiles of Flooring C.D.work Bituminou
Building Metal, metal Rock R.C.C. Laterite s Material
Rubish Stone aggre. soiling Blocks, Stone.
below 40mm stone G.I. Sheet
40mm, normal
normal size &
brick above
Task / 6.00 5.75 (Cum) 5.50 4.70 (Cum) 9.00 M.T. 7.50M.T. 45.00 (No) 3500 6.0 cumt 5000 No. 110 Sqm 30 Rmt. 15 Rmt. 5 Rmt. L.F. 5.50
Trip (Cum) (Cum) (No) (Unit
Cum)
Unit Cumt Cumt Cumt Cumt per M.T. per M.T. per no. per Cumt per 1000 per sqm Rmt. Rmt. Rmt. Cumt
1000no. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
0.50 873.67 145.61 151.94 158.85 185.89 97.07 116.49 19.41 249.62 145.61 174.73 7.94 29.12 58.24 174.73 158.85
1.00 938.02 156.34 163.13 170.55 199.58 104.22 125.07 20.84 268.01 156.34 187.60 8.53 31.27 62.53 187.60 170.55
1.50 1001.34 166.89 174.15 182.06 213.05 111.26 133.51 22.25 286.10 166.89 200.27 9.10 33.38 66.76 200.27 182.06
2.00 1061.48 176.91 184.60 193.00 225.85 117.94 141.53 23.59 303.28 176.91 212.30 9.65 35.38 70.77 212.30 193.00
2.50 1120.33 186.72 194.84 203.70 238.37 124.48 149.38 24.90 320.10 186.72 224.07 10.18 37.34 74.69 224.07 203.70
3.00 1183.35 197.22 205.80 215.15 251.78 131.48 157.78 26.30 338.10 197.22 236.67 10.76 39.44 78.89 236.67 215.15
249
3.50 1238.34 206.39 215.36 225.15 263.48 137.59 165.11 27.52 353.81 206.39 247.67 11.26 41.28 82.56 247.67 225.15
4.00 1300.40 216.73 226.16 236.44 276.68 144.49 173.39 28.90 371.54 216.73 260.08 11.82 43.35 86.69 260.08 236.44
4.50 1352.68 225.45 235.25 245.94 287.80 150.30 180.36 30.06 386.48 225.45 270.54 12.30 45.09 90.18 270.54 245.94
5.00 1413.81 235.64 245.88 257.06 300.81 157.09 188.51 31.42 403.95 235.64 282.76 12.85 47.13 94.25 282.76 257.06
6.00 1522.44 253.74 264.77 276.81 323.92 169.16 202.99 33.83 434.98 253.74 304.49 13.84 50.75 101.50 304.49 276.81
7.00 1640.29 273.38 285.27 298.23 349.00 182.25 218.71 36.45 468.65 273.38 328.06 14.91 54.68 109.35 328.06 298.23
8.00 1745.39 290.90 303.55 317.34 371.36 193.93 232.72 38.79 498.68 290.90 349.08 15.87 58.18 116.36 349.08 317.34
9.00 1862.16 310.36 323.85 338.57 396.20 206.91 248.29 41.38 532.04 310.36 372.43 16.93 62.07 124.14 372.43 338.57
10.00 1958.86 326.48 340.67 356.16 416.78 217.65 261.18 43.53 559.67 326.48 391.77 17.81 65.30 130.59 391.77 356.16
15.00 2546.04 424.34 442.79 462.92 541.71 282.89 339.47 56.58 727.44 424.34 509.21 23.15 84.87 169.74 509.21 462.92
20.00 2792.80 465.47 485.70 507.78 594.21 310.31 372.37 62.06 797.94 465.47 558.56 25.39 93.09 186.19 558.56 507.78
25.00 3290.89 548.48 572.33 598.34 700.19 365.65 438.79 73.13 940.25 548.48 658.18 29.92 109.70 219.39 658.18 598.34
30.00 3452.55 575.42 600.44 627.74 734.58 383.62 460.34 76.72 986.44 575.42 690.51 31.39 115.08 230.17 690.51 627.74
35.00 3915.08 652.51 680.88 711.83 833.00 435.01 522.01 87.00 1118.59 652.51 783.02 35.59 130.50 261.01 783.02 711.83
40.00 4042.57 673.76 703.06 735.01 860.12 449.17 539.01 89.83 1155.02 673.76 808.51 36.75 134.75 269.50 808.51 735.01
45.00 4440.95 740.16 772.34 807.45 944.88 493.44 592.13 98.69 1268.84 740.16 888.19 40.37 148.03 296.06 888.19 807.45
50.00 4850.70 808.45 843.60 881.95 1032.06 538.97 646.76 107.79 1385.92 808.45 970.14 44.10 161.69 323.38 970.14 881.95
Lead in Cost per Earth, Sand, Hand Rubble Steel, Bulk Asphalt in Bricks Concrete Roofing All Types R.C.C.Hume pipe for Hot Mix
KMS Trip Murum, crushed brokan Excavated Cement, Bituman Drum block & Tiles of Flooring C.D.work Bituminou
Building Metal, metal Rock R.C.C. Laterite s Material
Rubish Stone aggre. soiling Blocks, Stone.
below 40mm stone G.I. Sheet
40mm, normal
normal size &
brick above
Task / 6.00 5.75 (Cum) 5.50 4.70 (Cum) 9.00 M.T. 7.50M.T. 45.00 (No) 3500 6.0 cumt 5000 No. 110 Sqm 30 Rmt. 15 Rmt. 5 Rmt. L.F. 5.50
Trip (Cum) (Cum) (No) (Unit
Cum)
Unit Cumt Cumt Cumt Cumt per M.T. per M.T. per no. per Cumt per 1000 per sqm Rmt. Rmt. Rmt. Cumt
1000no. No.
60.00 5643.69 940.61 981.51 1026.13 1200.78 627.08 752.49 125.42 1612.48 940.61 1128.74 51.31 188.12 376.25 1128.74 1026.13
70.00 6026.34 1004.39 1048.06 1095.70 1282.20 669.59 803.51 133.92 1721.81 1004.39 1205.27 54.78 200.88 401.76 1205.27 1095.70
80.00 6778.08 1129.68 1178.80 1232.38 1442.14 753.12 903.74 150.62 1936.59 1129.68 1355.62 61.62 225.94 451.87 1355.62 1232.38
90.00 7537.21 1256.20 1310.82 1370.40 1603.66 837.47 1004.96 167.49 2153.49 1256.20 1507.44 68.52 251.24 502.48 1507.44 1370.40
100.00 8280.44 1380.07 1440.08 1505.53 1761.79 920.05 1104.06 184.01 2365.84 1380.07 1656.09 75.28 276.01 552.03 1656.09 1505.53
125.00 10268.29 1711.38 1785.79 1866.96 2184.74 1140.92 1369.10 228.18 2933.80 1711.38 2053.66 93.35 342.28 684.55 2053.66 1866.96
150.00 12148.12 2024.69 2112.72 2208.75 2584.71 1349.79 1619.75 269.96 3470.89 2024.69 2429.62 110.44 404.94 809.87 2429.62 2208.75
175.00 14031.96 2338.66 2440.34 2551.26 2985.52 1559.11 1870.93 311.82 4009.13 2338.66 2806.39 127.56 467.73 935.46 2806.39 2551.26
200.00 15881.07 2646.84 2761.92 2887.47 3378.95 1764.56 2117.48 352.91 4537.45 2646.84 3176.21 144.37 529.37 1058.74 3176.21 2887.47
250
Statement 'C2'
LOADING, UNLOADING & STACKING
Rates for 2015-16
Loading Unloading Stacking
Sr.
Materials Unit carriage carriage carriageupto
No.
upto 50 m upto 50 m 50 m lead
lead lead
Boulders, Rubble stones and metal of all
1 the sizes Cu.m. 27.47 17.17 17.17
251
MATERIAL RATES
Sr No Description Unit Rate `
Building-Bd-A : Excavation
1 Blasting Powder Kilogram 223.00
2 Detonator Number 70.50
3 Fuse Number 29.50
4 Nipple For Fastening Detenator Number 34.60
5 Noble Dynamite Kilogram 160.00
6 Red Tape Safety Fuse Running Meter 54.00
7 Soft Murum Cu.Mt. 92.00
8 Quarry Spoul Cu.Mt. 235.00
9 Rubble Stone (Blasted) Cu.Mt. 328.00
252
Sr No Description Unit Rate `
4 Aggregate 12 mm Cu.Mt. 714.00
5 Jungle wood (non teak) normal Cubic Meter 32899.00
253
Sr No Description Unit Rate `
Building-Bd-I : Cement Concrete Stone Masonry
254
Sr No Description Unit Rate `
3 Polydee-TP42 Primer Litre 160.00
4 Polydee-LM Kilogram 448.00
5 Polydee-LM. Kilogram 448.00
6 Polydee-LM 150mm width Running Meter 482.00
7 Bituflex Cloesdcell foam 30x30 mm Running Meter 48.00
8 AG 10 Granules Kilogram 14.00
9 Polydee-41 sealant and polyseal Kilogram 375.00
10 Polydee-MC Kilogram 306.00
11 Polydee-11 Kilogram 1068.00
12 Bitumen pad 12 mm thick Square Meter 870.00
13 Hold fast Iron 300*40*5mm Number 51.00
14 Aluminium Section Kilogram 381.00
15 Stainless Steel Plate 202 grade Kilogram 210.00
255
Sr No Description Unit Rate `
14 Black Kadappa (both side polish) (Machine cut) Square Meter 440.00
25mm thick
15 Black Kadappa (both side polish) (Machine cut) 25 Square Meter 460.00
mm to 40mm thick
16 Both Sides Polished Kadappa stone 25mm thick Square Meter 440.00
17 Kota stone (Machine cut) upto 25-30mm thick one Square Meter 560.00
side polished
18 Kota stone (Hand cut) upto 25-30mm thick one side Square Meter 530.00
polished
19 Kota stone for step polished) upto 25mm thick Square Meter 610.00
(1.2*0.3M)
20 White glazed tiles 20 * 10cm Number 39.00
21 Colour glazed tiles 20 * 10cm Number 48.00
22 Ceramic tiles 20*20cm Square Meter 368.00
23 Ceramic tiles 30*30cm Square Meter 405.00
24 Ceramil tiles first quality 45 x 45 cm Square Meter 468.00
25 Ceramic Antiskid first quality Flooring Tiles 30 x 30 Square Meter 475.00
cm
26 Ceramic Tiles first quality for dado 200 mm x Square Meter 352.00
300mm
27 Ceramic Tiles first quality for dado 30 x 45 cm Square Meter 506.00
28 Ceramic Tiles first quality for dado 30 x 60 cm Square Meter 660.00
29 Ceramic matt finish tiles first quality 60 x 60 cm Square Meter 825.00
30 Ceramic Tiles for dado 20 x 30 cm Square Meter 320.00
31 Heavy duty interlocking concrete block 60mm thick Square Meter 666.00
gray 300 kg/sq.cm.
32 Heavy duty interlocking concrete block 60mm thick Square Meter 666.00
coloured 300kg/sq.cm
33 Heavy duty interlocking concrete block 80mm thick Square Meter 787.50
gray 300kg/sq.cm
34 Heavy duty interlocking concrete block 80mm thick Square Meter 787.50
coloured 300kg/sq.cm
35 Heavy duty interlocking concrete block 80mm thick Square Meter 787.50
rubber mould glossy 400kg/sq.cm
36 Heavy duty interlocking concrete block 40mm thick Square Meter 544.50
gray 200kg/sq.cm
37 Heavy duty interlocking concrete block 40mm thick Square Meter 544.50
colour 200 kg/sq.cm
38 Black Granite Premium Quality Square Meter 2800.00
39 Green marble Square Meter 2000.00
40 Vitrified tiles Glossy first quality Size 590 to Square Meter 850.00
605mm* 590 to 605mm
256
Sr No Description Unit Rate `
41 Vitrified first quality matt finish - size 590 to 605mm* Square Meter 910.00
590 to 605mm
42 Vitrified first quality matt finish tiles - size 800mm x Square Meter 1170.00
800 mm.
43 Vitrified first quality glossy finish - size 800mm x Square Meter 935.00
800 mm.
44 Vitrified rustic matt stone finish size 590 to 605mm Square Meter 1029.00
*590 to 605mm*8 to 10mm
45 Vertified stone effect finish size 590 to 605mm* 590 Square Meter 1149.75
to 605mm * 8 to 10mm
46 Calcet Powder Kilogram 42.00
47 Black Oxide powder Kilogram 104.00
48 Fevi Matt Chemical 10 Kg Bag bags 1750.00
49 Marble chips Kilogram 42.00
50 Heavy duty interlocking concrete block 60mm thick Square Meter 605.00
rubber mould glossy 400kg/sq.cm
51 Tremix Treatment 100 mm thick Square Meter 92.00
52 Colour glazed tiles 20 * 10 cm Dozon 300.00
53 Ceramic tiles marble finish 45 * 45 Square Meter 756.00
54 Makrana marble slab 20 mm white Square Meter 2200.00
55 Plain cement tiles Square Meter 165.00
56 Chequrred cement tile Square Meter 497.00
57 Adhesive Mortar 5 Kg. / Sqmt. Cubic Meter 25.00
58 Tandoor Polished 40 mm thick Square Meter 519.00
59 Red Granite Premium Quality Square Meter 3000.00
60 Both side polished kadappa stone 25mm thick Square Meter 675.00
(1.5*0.45)
61 Marble Mosaic tiles (gray) (0.25*0.25m) Square Meter 445.00
62 Marble Mosaic tiles (white / coloured) Square Meter 460.00
63 Marble mosaic chequered tiles (gray) Square Meter 510.00
64 Marble Powder Kilogram 23.20
65 Pigments for tiles Kilogram 50.00
66 White glazed tiles 15*15cm Dozon 255.00
67 Colour glazed tiles 15*15cm Dozon 273.00
68 Jointless ceramic tiles 600*600 Square Meter 828.00
69 Sand - Crushed Cubic Meter 1000.00
70 Metalic floor hardner Kilogram 17.00
71 Black Granite Premium Quality Square Meter 2800.00
72 Heavy duty interlocking concrete block 60mm thick Square Meter 605.00
rubber mould glossy 400kg/sq.cm
257
Sr No Description Unit Rate `
Building-Bd-N : Wood finish
1 Bees wax Kilogram 97.00
2 Coal Tar Kilogram 71.00
3 French Polish Litre 179.00
4 Varnish Litre 351.00
5 Malemaine Polish Litre 665.00
6 C.C.T.W. Ballies 125 mm Diameter Running Meter 162.00
Building-Bd-P : Colour,white
washing,distempering
1 Neel Kilogram 237.00
2 Oil bound distemper Kilogram 182.00
3 Red powder / Geru Kilogram 35.00
4 Saras Kilogram 137.00
5 Scrapping sand paper size (30x20cm) Number 84.00
6 Dry distemper Kilogram 83.00
7 Plastic emulsion paint Litre 265.00
8 Chunam / White lime Powder Kilogram 30.50
9 Catonic emulsion paint Kilogram 425.00
258
Sr No Description Unit Rate `
Building-Bd-Q : Wood work
1 Ghana teak wood (Planks) Cubic Meter 88200.00
2 Ghana teak wood (Joist / Scantlings / Battens etc) Cubic Meter 74526.00
259
Sr No Description Unit Rate `
40 G.I.Screw 50mm Dozon 10.00
41 G.I. Nut Bolt Number 10.00
42 Nut Bolts 16mm dia. Kilogram 27.50
43 French Polish Litre 179.00
44 Handle 125mm M.S. Chromium Plated Number 77.00
45 Tower bolt M.S. Chromium plated 10mm dia,length Number 150.00
150mm
46 Stainless Steel Hinges - 75mm 14 gauge (Heavy Number 200.00
Duty)
47 Handle 125mm M.S. Chromium Plated Number 77.00
260
Sr No Description Unit Rate `
26 Accostic Board 12 mm thick Square Meter 470.00
27 Gypsum Board 12.5 mm thick Square Meter 205.00
28 UPVC 3 layer trapezoidal 2.00 mm sheet Square Meter 702.00
29 Bitumen Washer Number 2.00
30 Partical board B.W.P.Phinol bond 12mm thick Square Meter 649.00
31 G.I.Clamps 100mm to 150mm Number 71.00
32 Teak wood battens 50*25mm Running Meter 114.00
33 Teak wood batten 25 mm * 12 mm Running Meter 105.00
34 Tarat 36" width (Gunny cloth) Running Meter 55.00
35 Jali chicken mesh Square Meter 370.00
36 Wire glass 6 mm thick Square Meter 1235.00
37 Nut Bolts washers 12mm dia. 25mm long Number 10.00
38 G.I.Washers Kilogram 60.00
39 Tower bolt M.S. Chromium plated 10mm dia,length Number 220.00
250mm
261
Sr No Description Unit Rate `
21 Handle Ornamental Brass Number 340.00
22 Hinges Iron Oxidised 125mm Number 89.00
23 Hinges Iron Oxidised 100mm Number 42.00
24 Hinges Iron Oxidised 75mm Number 15.00
25 But Hinges Alluminium 125mm Number 87.00
26 But Hinges Alluminium 100mm Number 69.00
27 But Hinges Alluminium 90mm Number 59.00
28 Brass Double Acting Spring Hinges 100 mm 14 Number 716.00
guage
29 G.I.Screw 125mm Dozon 650.00
30 G.I.Screw 100mm Dozon 381.00
31 G.I.Screw 75mm Dozon 129.00
32 G.I.Screw 50mm Dozon 10.00
33 G.I.Screw 25mm Dozon 25.00
34 Stainless Steel Hinges - 100mm 14 gauge (Heavy Number 260.00
Duty)
35 Stainless Steel Hinges - 125mm 14 gauge (Heavy Number 350.00
Duty)
36 Stainless Steel Hinges - 75mm 14 gauge (Heavy Number 200.00
Duty)
37 Tower bolt brass oxidised 10mm dia.length 300mm Number 107.00
262
Sr No Description Unit Rate `
51 Tower bolt Iron oxidised 10mm dia.length 250mm Number 107.00
263
Sr No Description Unit Rate `
83 Glass plain 5mm Square Meter 495.00
84 Acrylic Plain Sheet 3 mm Square Meter 1080.00
85 Glass obscured (bajara) 3mm Square Meter 396.00
86 Glass obscured (bajara) 5mm Square Meter 640.00
87 Brass oxidised hooks and eyes 200mm Number 94.00
88 Brass oxidised hooks and eyes 225mm Number 101.00
89 Iron oxidised hooks and eyes 100 mm Number 26.00
90 Iron oxidised hooks and eyes 200 mm Number 40.00
91 Aluminium hooks and eyes 200 mm Number 40.00
92 Chromium plated hooks and eyes 200 mm Number 73.00
93 Bearing roller glazed window shutter Number 101.00
94 Stopper for steel window Number 73.00
95 G.I. Nut Bolt Number 10.00
96 Housing box to rolling shutter Square Meter 2457.00
97 Mechanical Gear For Rolling Shutter Number 855.00
98 Mortise lock superior Number 742.00
99 Solid Core commercial shutter 30mm thick phenol Square Meter 1156.00
bonded with face veneer 3 mm thick both side
264
Sr No Description Unit Rate `
118 Lock for Sliding Shutter Number 84.00
119 All Bearing Roller Number 101.00
120 All Frame Rail Angle Kilogram 287.00
121 Welding Electrodes Number 8.00
122 M.S. Angle / Flat Kilogram 74.00
123 C.R.C. Sheet Square Meter 528.00
124 Abstrone Butadyne Styrine (ABS) Door Shutter Number 620.00
including Transportation
125 Puff Insulation 35-40 Kg/Cumt. Density Kilogram 265.00
126 G.I.Precoated trapezoidal zinc coated sheets Square Meter 282.00
0.50mm thick
127 PVC Door Shutter 29 mm thick Factory Made Square Meter 3140.00
Shutter
128 PVC Door Shutter 34 mm thick Factory Made Square Meter 3961.00
Shutter
129 FRP Door Shutter 30 mm thick Factory Made Square Meter 2542.00
Shutter
130 FRP Door Shutter 35 mm thick Factory Made Square Meter 2655.00
Shutter
131 P.V.C. Gasket for Glass Running Meter 39.00
132 Bison Pannel 8 mm Square Meter 365.00
133 Bison Pannel 6 mm Square Meter 290.00
134 Bison Pannel 12 mm Square Meter 545.00
135 G.I.Hook 25mm Number 26.00
136 P.V.C. Sheet 5 mm Running Meter 914.00
137 PVC factory made solid panel door shutter 35 mm Square Meter 3810.00
with stainless steel fixutres & fastening
138 PVC facory made flush door 30 mm with stainless Square Meter 3750.00
steel fixtures & fastening
139 Hyddrulic door closer heavy duty Number 1200.00
140 Stainless Steel pipes 50 mm Running Meter 400.00
141 Stainless Steel pipes 40 mm Running Meter 330.00
142 40 mm flush door Square Meter 1614.00
143 ACP sheet 4 mm Square Meter 1200.00
144 Meta colour sheet Square Meter 2500.00
145 Polycarbonate sheet 6 mm hollow Square Meter 452.00
146 Polycarbonate sheet 3 mm Solid Square Meter 1022.00
147 M.S. Ventilator Shutter & frame 50 Kg/sq.mtr/ Square Meter 1231.00
148 Decorative Ply -veneer 4 mm thick Square Meter 589.00
149 Ply wood 9mm thick Square Meter 605.00
150 Face Vener Board 4mm thick Square Meter 609.00
151 Laminated board double 12mm thick Square Meter 410.00
152 Mosquito proof Nylone net Square Meter 157.00
265
Sr No Description Unit Rate `
153 Solid core shutter 30mm thick with commercial Square Meter 1156.00
veneer facing and phenol bonded 3 mm thick both
side
266
Sr No Description Unit Rate `
35 C.I.Bend 100mm dia. Number 315.00
36 C.I.Grating 150mm dia. Number 95.00
37 C.I.Grating 100mm dia. Number 94.00
38 C.I.Grating 75mm dia. Number 87.00
39 C.I.Brackets Pair 100.00
40 C.I.Collers 100mm dia. Number 285.00
41 C.I.Copllers 75mm dia. Number 265.00
42 C.I.Cowl / Vent 100mm dia. Number 642.00
43 C.I.Cowl / Vent 150mm dia. Number 242.00
44 C.I.Cowl / Vent 75mm dia. Number 166.00
45 C.I.Man hole cover 75 kg. Number 1245.00
46 C.I.Nahani trap 100mm dia.(375mm long) Number 414.00
47 C.I.Nahani trap 75 to 80mm dia.(375mm long) Number 382.00
48 C.I.Soil pipe 100mm dia. Running Meter 703.00
49 C.I.Soil pipe 150mm dia. Running Meter 1257.00
50 C.I,Soil pipe 75 to 80mm dia. Running Meter 700.00
51 C.I.Shoe 75 mm dia. Number 410.00
52 C.I. Shoe 100 mm dia. Number 410.00
53 Ball cock 15mm dia.P.V.C.FLOAT Number 231.00
54 Ball cock 25mm dia.P.V.C.FLOAT Number 444.00
55 Ball cock 40mm dia.P.V.C.FLOAT Number 1975.00
56 Ball cock 50mm dia.P.V.C.FLOAT Number 3200.00
57 Bid cock stop tap brass heavy 15mm Number 245.00
58 Bid stop cock tap brass heavy 15mm Number 395.00
59 Bid cock stop tap brass heavy 20mm Number 336.00
60 Bid cock stop tap brass heavy 25mm Number 405.00
61 Bid tap 12mm brass medium Number 157.00
62 Colour wash hand basin 55*40cm Number 1000.00
63 Colour wash hand basin 63*45cm Number 1200.00
64 White glazed wash basin 45*30cm Number 600.00
65 White glazed wash hand basin 55*50cm Number 900.00
66 P.V.C. flexible Waste Pipe 32 mm dia Number 25.00
67 White Glazed Wash Hand Basin 63 x 45 cm Number 950.00
68 Colour glazed wash hand basin 450 x 203 Number 700.00
69 Sink white glazed 45*20*30cm Number 1462.00
70 Pedestal for wash basin (standard size) Number 1550.00
71 C.C.Septic tank 0.9m dia.(2.5m long) Number 13997.00
72 C.C.Septic tank 1.20m dia.(2.5m long) Number 15009.00
73 C.I.Cover with frame (Gully trap) Number 336.00
74 C.I.Plug Bend 150MM dia. Number 885.00
75 Clamp for G.I.pipe 25mm Number 29.00
76 Colour European type W.C.Pan Number 1678.00
267
Sr No Description Unit Rate `
77 European type glazed W.C.pan Number 1249.00
78 W.C.PAN 64 CM.1st class with tap Number 2000.00
79 Colour European type glazed W.C.pan Number 1678.00
80 Colour European type glazed W.C.pan Number 1500.00
81 W.C.PAN 68 CM.1st class with tap (Orissa) Number 2100.00
82 W.C.PAN Coloured glazed 64CM.(Orissa) Number 2077.00
83 W.C.PAN White glazed 58 CM.Indian and Number 1155.00
AngloIndian.
84 W.C.PAN White glazed 64 CM (Orissa) Number 2275.00
85 W.C.PAN White glazed 57.50 CM (Orissa) Number 810.00
86 W.C.PAN Colour glazed 57.50 CM (Orissa) Number 1320.00
87 W.C.PAN with P trap 685mm Number 1007.00
88 Fibre flushing tank for W.C. Number 975.00
89 Flushing tank automatic Urinal 10ltr. C.I. Number 1706.00
90 Flushing tank P.V.C 10ltr. Number 1300.00
91 Flushing tank automatic Urinal 5ltr. (P.V.C.) Number 823.00
92 Low level flush pr. St. 10ltr. Number 1300.00
93 Low level flushing cistern Number 975.00
94 Flat back Urinal Number 1034.00
95 Urinal semi stall Number 2200.00
96 Lipped type Urinal Number 886.00
97 Coloured glazed full stall Urinal Number 3500.00
98 White glazed full stall Urinal Number 3134.00
99 Squatting plate type Urinal Number 1500.00
100 Wheel stop tap brass 15mm Number 239.00
101 Wheel stop tap brass 20mm Number 289.00
102 Wheel stop tap brass 25mm Number 370.00
103 Socket brass for 32mm tap Number 63.00
104 Socket brass for 40mm tap Number 75.00
105 Socket brass for 50mm tap Number 99.00
106 Socket brass for 65mm tap Number 116.00
107 Socket for 100mm tap Number 157.00
108 Socket for 15mm tap Number 52.00
109 Socket for 20mm tap Number 60.00
110 Socket for 25mm tap Number 70.50
111 Socket for 32mm tap Number 72.00
112 Socket for 40mm tap Number 89.00
113 Socket for 50mm tap Number 115.00
114 Socket for 65mm tap Number 135.00
115 Socket for 80mm tap Number 161.00
116 Socket for G.I.PIPE 150mm tap Number 167.00
117 Span Yarn Number 151.00
268
Sr No Description Unit Rate `
118 Strainer for 100mm Number 1975.00
119 Strainer for 40mm Number 589.00
120 Strainer for 50mm Number 680.00
121 Strainer for 80mm Number 978.00
122 Strainer for 15mm Number 91.00
123 Strainer for 20mm Number 173.00
124 Strainer for 25mm Number 279.00
125 Stone ware pipe 100mm dia. Running Meter 165.00
126 Stone ware pipe 150mm dia. Running Meter 220.00
127 Stone ware pipe 225mm dia. Running Meter 334.00
128 Stop tap brass with crunch wheel 15mm dia. Number 263.00
129 Towel rod with clamps 16mm dia. Number 157.00
130 Mirror 40*50cm. With plastic frame Number 765.00
131 Brass T Thimble Socket 32mm dia. Pair 110.00
132 Brass Thimble Socket 32mm dia. Number 350.00
133 Brass wheel stop tap 32mm dia. Number 553.00
134 Brass wheel stop tap 40mm dia. Number 706.00
135 Brass wheel stop tap 50mm dia. Number 892.00
136 Brass wheel stop tap 65mm dia. Number 620.00
137 Brass wheel stop tap 80mm dia. Number 775.00
138 Half turn flush cock 25mm dia. Number 239.00
139 12mm flexble inlet pipe connection Number 75.00
140 Bell mouth cover 100mm dia. Number 92.00
141 Box chamber with lock 0.6*0.45m Number 422.00
142 Brass nozzle pillar tap 12mm Number 318.00
143 Black bakelite seat to european closer Number 108.00
144 Concussion push button type gun metal tap 15 to Number 172.00
25mm dia.
145 Coupling cast Iron 100mm dia. Number 223.00
146 Coupling cast Iron 80mm dia. Number 204.00
147 Chromium plated 12mm dia.bib cock Number 325.00
148 Chromium plated brass fountain jet Number 177.00
149 C.I.Tee Number 572.00
150 C.I.Trap grating 15*10 cm Number 299.00
151 C.I.Y junction 100mm dia. Number 624.00
152 C.I.Y junction 150mm dia. Number 2034.00
153 C.I.Y junction 75mm dia. Number 597.00
154 Ferrul for C.I.pipr 100mm Number 522.00
155 Half round earthware pipe 100mm(60cm long) Number 657.00
156 Hump rope Kilogram 65.00
157 Half round china ware pipe 100mm(60cm long) Number 40.00
158 Half round china ware pipe 75mm(60cm long) Number 52.00
269
Sr No Description Unit Rate `
159 Lead pipe 12mm dia. Running Meter 100.00
160 Lead pipe 32mm dia. Running Meter 311.00
161 Lead pipe 40mm dia. Running Meter 395.00
162 Lead plate Kilogram 190.00
163 Mohagani seat with lid Number 389.00
164 Mosquito proof coupling Number 70.50
165 Mosquito proof coupling --Select-- 270.00
166 Non-return valve 15mm for water meter Number 316.00
167 Non-return valve 25mm for water meter Number 900.00
168 Non-return valve 20mm for water meter Number 570.00
169 Piller tap 12mm dia.chromium plated heavy Number 348.00
170 P.Trap and lead pipe upto 40mm dia. Number 275.00
171 Rubber Incertion Kilogram 98.00
172 Rubberised adhesive Litre 423.00
173 Salt glazed stone ware gully trap (150*150mm) Number 128.00
174 Sewer trap Number 385.00
175 Shower rose chromium plated brass 10cm Number 272.00
176 P.V.C. pipe 15mm dia.10kg pressure(class IV) Running Meter 67.00
177 P.V.C. pipe 20mm dia.10kg pressure(class IV) Running Meter 80.00
178 P.V.C. pipe 25mm dia.10kg pressure(class IV) Running Meter 115.00
179 P.V.C. pipe 32mm dia.10kg pressure(class IV) Running Meter 140.00
180 P.V.C. pipe 40mm dia.10kg pressure(class IV) Running Meter 148.00
181 Piller tap 12mm dia.chromium plated light Number 348.00
182 Bleaching Powder Kilogram 68.00
183 Potassium Permanganate Kilogram 414.00
184 Nylon Brush Number 125.00
185 Duster Number 20.00
186 Plastic Bucket Number 150.00
187 Coir Kilogram 85.00
188 Gunny Cloth Running Meter 30.00
189 Kharata Number 50.00
190 P.V.C. pipe 50mm dia.10kg pressure(class IV) Running Meter 155.00
191 P.V.C. pipe 60mm dia.10kg pressure(class IV) Running Meter 161.00
192 P.V.C. pipe 75mm dia.4 kg pressure(class II) Running Meter 170.00
193 P.V.C. 75 mm Soil Pipe 6 Kg Pressure Running Meter 78.75
194 P.V.C. pipe 90mm dia.4 kg pressure(class II) Running Meter 119.75
195 P.V.C.pipe 110mm dia.4kg.pressure (class II) Running Meter 140.00
196 P.V.C. 110 mm Rain Water Pipe 6Kg Pressure Running Meter 245.00
197 P.V.C. 110 mm Soil Pipe 6 Kg Pressure Running Meter 245.00
198 P.V.C.pipe 140mm dia.4kg.pressure (class II) Running Meter 310.00
199 P.V.C.pipe 160mm dia.4kg.pressure (class II) Number 425.00
200 P.V.C.pipe 160mm dia.Soil Pipe Running Meter 370.00
270
Sr No Description Unit Rate `
201 P.V.C.pipe 160mm dia. Rain Water Pipe Running Meter 370.00
202 P.V.C.Socket 15mm dia. Number 8.00
203 P.V.C.Socket 20mm dia. Number 8.00
204 P.V.C.Socket 25mm dia. Number 15.00
205 P.V.C.Socket 32mm dia. Number 18.00
206 P.V.C.Socket 40mm dia. Number 25.00
207 P.V.C.Socket 50mm dia. Number 30.00
208 P.V.C.Socket 60mm dia. Number 35.00
209 Bottle trap chromium plated 32mm dia. Number 750.00
210 Stainless Steel sink of size 600*510*200mm of Number 3150.00
nirali or equivalent make
211 Stainless Steel sink of size 610 x 460 x 200 mm of Number 2845.00
nirali or equivalent make
212 Stainless Steel sink of size 470 x 420 x 178 mm of Number 2120.00
nirali or equivalent make
213 C.P.pillar cock long neck with aerator jaquar make Number 1300.00
continental (Cat.No. CON-021)
214 C.P.Bib Cock long thread jaquar make continental Number 750.00
(Cat.No. CON-039)
215 C.P.2-way bib cock jaquar make continental Number 1000.00
(Cat.No. CON-041)
216 C.P.Angular stop cock long thread jaquar make Number 700.00
continental (Cat.No. CON-055)
217 C.P.wall mixer with provision for overhead shower Number 3300.00
with 115mm long bend pipe and wall flange jaquar
make continental (Cat.No. CON-273UPR)
218 C.P.sink cock with raised 'J' shaped swinging casted Number 1350.00
spout (table mounted) jaquar make continental
(Cat.No. CON-359)
219 CPCV pipe 15mm dia. Running Meter 55.00
220 CPCV pipe 20mm dia. Running Meter 73.00
221 CPCV pipe 25mm dia. Running Meter 110.00
222 CPCV pipe 32mm dia. Running Meter 175.00
223 CPCV pipe 40mm dia. Running Meter 257.50
224 CPCV pipe 50mm dia. Running Meter 430.50
225 Ball cock for 15mm dia. Number 231.00
226 Ball cock for 12mm dia. Number 206.00
227 Ball cock for 25mm dia. Number 444.00
228 R.C.C.Chamber cover with frame 90cm*45cm Number 1982.00
Heavy Duty 225kg
229 R.C.C.Chamber cover with frame 90cm*45cm Number 1226.00
Medium Duty 140kg
271
Sr No Description Unit Rate `
230 R.C.C.Chamber cover with frame 60cm*45cm Number 1796.00
Heavy Duty 160kg
231 R.C.C.Chamber cover with frame 60cm*45cm Number 894.00
Medium Duty 100kg
232 I.S.I.Ferrul Connection15mm dia. Number 375.00
233 I.S.I.Ferrul Connection 20mm dia. Number 425.00
234 I.S.I.Ferrul Connection 25mm dia. Number 895.00
235 I.S.I.Ferrul Connection 32mm dia. Number 1275.00
236 I.S.I.Ferrul Connection 40mm dia. Number 2200.00
237 I.S.I.Ferrul Connection 50mm dia. Number 3200.00
238 Water meter 15 mm diameter Number 1228.00
239 Water meter 20 mm diameter Number 1677.00
240 Water meter 25 mm diameter Number 2074.00
241 Water meter 40 mm diameter Number 7754.00
242 Water meter 50 mm diameter Number 7826.00
243 Water meter 80 mm diameter Number 7861.00
244 Water meter 100 mm diameter Number 9064.00
245 Non return Valve 40 mm diameter Number 1425.00
246 Non return Valve 50 mm diameter Number 1745.00
247 Non return Valve 80 mm diameter Number 4785.00
248 Non return Valve 100 mm diameter Number 8150.00
249 Colour Wash Hand Basin 0.45 x 0.30 Number 961.00
250 White Glaze Earth Sink 0.6 x 0.2 x 0.45 Number 2350.00
251 Clamp for G.I.pipe 200mm Number 64.00
252 Earopean type glazed W.C.pan 68cm Number 1597.00
253 Earopean white glazed earthen ware closet pan Number 1096.00
254 P.V.C. Nahni Trap Running Meter 95.00
255 P.V.C. Connector. 15 mm dia Number 75.00
256 G.I.Chain 12mm dia. Running Meter 164.00
257 G.I.Chain 28mm dia. Running Meter 492.00
258 G.I.Screws 25mm dia. Number 7.00
259 PVC Nahani Trap 75 mm Number 95.00
260 PVC Nahani Trap 150 mm Number 275.00
261 Anglo Indian W.C. Pan White Number 3481.00
262 Anglo Indian W.C. Pan Colour Number 5400.00
263 P.V.C. Cowl 100 mm Number 100.00
264 Ultra 250 mm. dia. uPVC 90 degree junction Number 1210.00
chamber base with U trap
265 Ultra 250 mm.dia. uPVC Cover & Frame Number 456.00
266 Ultra 450 mm dia. Polypropylene multiple inlet Number 1944.00
Inspection chamber base
272
Sr No Description Unit Rate `
267 Shaft pipe 450 mm dia, 460 mm height of HDPE Number 2680.00
material
268 R.C.C. Cover & Frame 175 KG. Number 2750.00
269 Ultra 600 mm dia.polypropylene 315 mm St. Number 8540.00
through,600 mm inbuilt shaft chamber
270 Shaft pipe 250 mm dia, 470 mm height of uPVC Number 456.00
material
271 Ultra 600 mm.dia. SFRC Cover & Frame Number 8893.00
272 uPVC Eccentric reducer 250 x 200 mm Number 762.00
273 uPVC Eccentric reducer 200 x 160 mm Number 527.00
274 uPVC Eccentric reducer 250 x 160 mm Number 799.00
275 uPVC Eccentric reducer 315 x 200 mm Number 2820.00
276 uPVC Blanking Plug 110 mm Number 83.50
277 uPVC Blanking Plug 160 mm Number 223.00
278 uPVC Coupler 110 mm click ring type Number 87.60
279 uPVC Coupler 160 mm click ring type Number 255.00
280 uPVC Coupler 200 mm click ring type Number 542.00
281 uPVC 90 degree bend Number 95.00
282 uPVC Insitu Adapter 110 mm (F) Number 179.20
283 uPVC Insitu Adapter 160 mm (F) Number 401.25
284 uPVC Bend 87.5 degree 110 mm CR Number 95.00
285 Rubber lubricant Litre 325.00
286 Eco- drain 110 mm SN 8 Nu- Drain Upvc pipes Running Meter 308.00
287 Eco- drain 160 mm SN 4 Nu- Drain Upvc pipes Running Meter 529.00
288 Eco- drain 200 mm SN 4 Nu- Drain Upvc pipes Running Meter 815.00
289 Bracket D type C. P. Number 48.00
290 Water jet with accessories Number 525.00
291 Ultra Shaft 250x470mm Number 452.00
292 Upvc sanitary pipes all 15 mm dia. Running Meter 47.50
293 Upvc sanitary pipes all 20 mm dia. Running Meter 64.00
294 Upvc sanitary pipes all 25 mm dia. Running Meter 96.75
295 Upvc sanitary pipes all 32 mm dia. Running Meter 113.25
296 Upvc sanitary pipes all 40 mm dia. Running Meter 159.00
297 Upvc sanitary pipes all 50 mm dia. Running Meter 223.65
298 Upvc sanitary pipes all 63 mm dia. Running Meter 312.00
299 Upvc sanitary pipes all 75 mm dia. Running Meter 475.00
300 Piller cock mixer & Algle cock Number 375.00
301 Bib cock Long Arm Number 618.75
302 Bottletrap wash basin 32 mm Cromium Plated Number 750.00
303 W. C. flush valve Number 2450.00
304 Solution for G.I. Pipe Kilogram 400.00
273
Sr No Description Unit Rate `
305 Stainless Steel sink of size 470 x 420 x 178 mm of Number 2120.00
nirali or equivalent make
306 C.I.Soil pipe 100mm dia. Running Meter 1267.00
307 C.I.Soil pipe 150mm dia. Running Meter 1263.00
308 C.I,Soil pipe 75 to 80mm dia. Running Meter 1263.00
309 Fire wood Quintal 586.00
310 Solvent Litre 195.00
311 12mm flexible inlet pipe connection No. 75.00
312 M.S. Locking Arrangement for gate Number 270.00
313 Screw bolt G. I. Number 16.80
314 Pedestal for wash basin (standard size) Number 1550.00
Building-Bd-W : Miscellaneous
1 P.V.C. Sheet Square Meter 914.00
2 Barbed Wire Kilogram 118.00
3 Chunam / White lime Powder Kilogram 30.50
4 Copper Tape width 25mm*3mm thick Kilogram 358.00
5 Cripped wire 3' - 0" , 4' - 0" and 5' - 0" wide Square Meter 164.00
6 Mosquito proof Nylone net Square Meter 157.00
7 Nylone Rope Kilogram 268.00
8 Tarat 36" width (Gunny cloth) Running Meter 55.00
9 Tatti Square Meter 16.00
10 Aluminium Strips 50 mm x 3 mm Running Meter 358.00
11 Clorophyriphoas Litre 220.00
12 D.D.V.P. Litre 222.00
13 Malathion Litre 160.00
14 Pine Oil Litre 68.00
15 Concentina Coil Wire Running Meter 305.00
16 Lightening Conductor Number 8032.00
17 Chain link 3' - 0" , 4' - 0" and 5' - 0" wide Square Meter 164.00
18 Salt Kilogram 11.00
19 Rustonil - Rust Removal cum phosphatic Agout Litre 671.00
20 Polysafe - plastone (Patent No. 57) Litre 760.00
21 Green marble Square Meter 2000.00
22 Hold fast for steel gate No. 138.00
23 Bamboo 50mm dia. Number 164.00
24 Karva (for roof and sides 10kg bundle) Bundle 20.00
25 Bamboo Matting 1.2*1.8m Square Meter 46.00
26 Weather sealant – Non staining (600 ml) No. 460.00
27 Weather sealant – Normal (300 ml) No. 145.00
28 M.S.Brackets / Aluminium Alloy Brackets Kilogram 100.00
29 Anchor Fastner M-10 No. 110.00
274
Sr No Description Unit Rate `
30 S.S. Bolt with washer of sizes of structural No. 35.00
31 S.S. screws of sizes for structural glazing No. 5.00
32 Protective Tape Kilogram 25.00
33 Baker rod Mtr. 5.00
34 G.I. flashing Sq.Mtr. 66.00
35 4 mm thick ACP Kilogram 887.00
36 Aluminium Section Kilogram 381.00
37 Aluminium coating Kilogram 125.00
275
Sr No Description Unit Rate `
30 Pad lock No 99.00
31 Empty asphalt drums No 666.00
32 T.W bullies 100 mm dia. Rmt 151.25
General-General
1 Cement Coloured Kilogram 95.00
2 Empity Cement Bag Number 2.00
3 Tor Steel (H.Y.S.D.) Metric Tonne 47300.00
4 Tubular Steel Metric Tonne 56000.00
5 Sand - Natural Cubic Meter 1500.00
6 Sand - Crushed Cubic Meter 1000.00
7 Sand - Course Cubic Meter 1500.00
8 Sand (Screened) Cubic Meter 1710.00
9 Fly Ash Brick size 230*100*80 mm 1000 Nos. 6450.00
10 Fly Ash Brick size 230*150*80 mm 1000 Nos. 7350.00
11 Rubble stone Blasted Cubic Meter 328.00
12 Aggregate 60 mm Blasted (Hand Broken) Cubic Meter 496.00
13 Aggregate 80 mm Blasted (Hand Broken) Cubic Meter 496.00
14 Aggregate 50 mm Blasted (Hand Broken) Cubic Meter 496.00
15 Aggregate 40 mm (Hand Broken) Blasted. Cubic Meter 584.00
16 Aggregate above 25 mm and upto 40mm Crushed Cubic Meter 654.00
276
Sr No Description Unit Rate `
20 Aggregate 10 mm Cubic Meter 721.00
21 Aggregate 6 mm Cubic Meter 727.00
22 Stone Dust Cubic Meter 413.00
23 Soft Murum Cubic Meter 92.00
24 Hard Murum Cubic Meter 118.00
25 Unstaked lime Metric Tonne 30.50
26 Water 1000 Litre 134.00
27 White Cement Kilogram 29.12
28 Plastizer Litre 115.00
29 Stainless Steel Plate 202 grade Kilogram 210.00
30 Stainless Steel Plate 304 grade Kilogram 357.00
31 Kerosen Litre 45.00
32 Admixture for concrete Kilogram 100.00
33 Expanded Polythene Sheet Square Meter 267.00
34 Bitumen pad 12 mm thick Square Meter 870.00
General-MORTH: Roads
1 Granular Material or hard murrum for GSB works at Cubic Meter 186.00
Site
2 Filter media/Filter Material as per Table 300-3 Cubic Meter 415.00
(MoRT&H Specification)
3 Close graded Granular sub-base Material 53 mm to Cubic Meter 674.00
9.5 mm
4 Close graded Granular sub-base Material 37.5 mm Cubic Meter 681.00
to 9.5 mm
5 Close graded Granular sub-base Material 26.5 mm Cubic Meter 673.00
to 9.5 mm
6 Close graded Granular sub-base Material 9.5 mm Cubic Meter 659.00
to 4.75 mm
7 Close graded Granular sub-base Material 9.5 mm Cubic Meter 635.00
to 2.36 mm
8 Close graded Granular sub-base Material 4.75mm Cubic Meter 643.00
to 2.36 mm
9 Close graded Granular sub-base Material 4.75mm Cubic Meter 639.00
to 75 micron mm
10 Coarse graded Granular sub-base Material 2.36 Cubic Meter 631.00
mm & below
11 Coarse graded Granular sub-base Material 4.75mm Cubic Meter 639.00
to 75 micron mm
12 Coarse graded Granular sub-base Material 4.75 Cubic Meter 643.00
mm to 2.36 mm
13 Coarse graded Granular sub-base Material 9.5 mm Cubic Meter 659.00
to 4.75 mm
277
Sr No Description Unit Rate `
14 Coarse graded Granular sub-base Material 26.5 Cubic Meter 655.00
mm to 4.75 mm
15 Coarse graded Granular sub-base Material 26.5 Cubic Meter 673.00
mm to 9.5 mm
16 Coarse graded Granular sub-base Material 37.5 Cubic Meter 681.00
mm to 9.5 mm
17 Coarse graded Granular sub-base Material 53 mm Cubic Meter 679.00
to 26 .5mm
18 Aggregates below 5.6 mm Cubic Meter 413.00
19 Aggregates 22.4 mm to 2.36 mm Cubic Meter 705.00
20 Aggregates 22.4 mm to 5.6 mm Cubic Meter 688.00
21 Aggregates 45 mm to 2.8 mm Cubic Meter 684.00
22 Aggregates 45 mm to 22.4 mm Cubic Meter 678.00
23 Aggregates 53 mm to 2.8 mm Cubic Meter 680.00
24 Aggregates 53 mm to 22.4 mm Cubic Meter 679.00
25 Aggregates 63 mm to 2.8 mm Cubic Meter 676.00
26 Aggregates 63 mm to 45 mm Cubic Meter 684.00
27 Aggregates 90 mm to 45 mm Cubic Meter 690.00
28 Aggregates 10 mm to 5 mm Cubic Meter 712.00
29 Aggregates 11.2 mm to 0.09 mm Cubic Meter 648.00
30 Aggregates 13.2 mm to 0.09 mm Cubic Meter 746.00
31 Aggregates 13.2 mm to 5.6 mm Cubic Meter 693.00
32 Aggregates 13.2 mm to 10 mm Cubic Meter 747.00
33 Aggregates 20 mm to 10 mm Cubic Meter 699.00
34 Aggregates 25 mm to 10 mm Cubic Meter 701.00
35 Aggregates 19 mm to 6 mm Cubic Meter 706.00
36 Aggregates 37.5 mm to 19 mm Cubic Meter 708.00
37 Aggregates 37.5 mm to 25 mm Cubic Meter 706.00
38 Aggregates 6 mm nominal size Cubic Meter 727.00
39 Aggregates 10 mm nominal size Cubic Meter 721.00
40 Aggregates 13.2/12.5 mm nominal size Cubic Meter 714.00
41 Aggregates 20 mm nominal size Cubic Meter 717.00
42 Aggregates 25 mm nominal size Cubic Meter 704.00
43 Aggregates 40 mm nominal size Cubic Meter 687.00
44 AC pipe 100 mm dia Running Meter 105.00
45 Acrylic polymer bonding coat Litre 330.00
46 Barbed wire Kilogram 118.00
47 Bearing (Cast steel rocker bearing assembly of 250 Number 110439.00
tonne )
48 Bearing (Elastomeric bearing assembly consisting of Number 23114.00
7 internal layers of elastomer bonded to 6 nos.
internal reinforcing steel laminates by the process of
vulcanisation,)
278
Sr No Description Unit Rate `
49 Bearing (Forged steel roller bearing of 250 tonne Number 110439.00
279
Sr No Description Unit Rate `
72 Preformed continuous chloroprene elastomer or Running Meter 633.00
closed cell foam sealing element with high tear
strength, vulcanised in a single operation for the full
length of a joint to ensure water tightness.
280
LABOUR RATES
Sr No Description Unit Rate
281
Sr No Description Unit Rate
282
RATE SCHEDULE
ANNEXURE "A"
RATE SCHEDULE FOR SUPPLY OF RCC PIPES ISI MARK ON THE RATE
CONTRACT FOR THE YEAR 2014-15.
2 MTR. LENGTH
80 487.60 510.92 536.36
100 510.92 535.30 561.80
150 551.20 576.64 605.26
200 602.08 630.70 662.50
225 629.64 659.32 716.56
250 677.34 710.20 746.24
300 997.46 1044.10 1096.04
2.5MTR.LENGTH
300 1394.96 1845.46 2274.76
350 1626.04 2573.68 2235.54
400 1768.08 3217.10 3022.06
450 2045.80 4020.58 4083.12
500 2585.34 4811.34 5172.80
600 3199.08 6102.42 6818.98
700 4538.92 8117.48 9423.40
800 5412.36 10503.54 12218.62
900 6504.16 11706.64 14108.60
1000 7501.62 13132.34 18053.92
1100 9966.12 17371.28 19859.10
1200 10844.86 17942.62 21200.00
1400 12797.38 21172.44 24670.44
1600 15100.76 24983.14 27138.12
1800 17819.66 29479.66 29851.72
a) Collars 10% of the accepted rate of full length of R.C.C. Pipes of 2 and 2.5
Mtr. Length of R.C.C. Pipes of the corresponding dia and Class.
b) Half Round Pipes At the half price of full round pipe of corresponding dia meter + 5% extra
for NP-2, NP-3, NP-4 Class Pipes.
c) Non-standard At the rate of full round R.C.C. Pipes of corresponding diameter for
Length Pipes corresponding length + 10 % Extra
283
ANNEXURE - B
OFFICE STATIONARY ITEMS FOR THE YEAR 2015-16
Approved
Sr. rates for
Particulars Unit
No. D.S.R. 2015-
16
1 2 3 4
1 Writing Paper (Full Size) Super Brand 7 kg Ream 500.00
2 Writing Paper (Half Size) Super Brand 7 kg Ream 500.00
3 Box 350.00
Carbon Paper Sliver black & Blue 503 full sheet 100 kores brand
4 Box 180.00
Carbon Paper Sliver black & Blue 503 Half sheet 100 kores brand
5 Rulled Register (Vertical & Horizontal) 1 to 12 quire 1 Quire 28.00
6 Rulled paper full sheet Ream 250.00
7 correcting ink fluid/pen Bottle/No. 25.00
8 Tag bundle (Red) 9" length (144 Nos. per bundle Bundle 40.00
9 Pin Box 250 gm each box Box 90.00
10 Candle Box 40.00
11 Dungri cloth in good quality Mtr.
12 Tocha (Pokhar) No. 25.00
13 Cello tape 1" wonder No. 20.00
14 No. 25.00
File Board (Thick) Printing of office Name with lace (asper sample)
15 No. 20.00
File Board (Thin) Printing of office Name with lace (asper sample)
16 Rapper (Two flap) thick Dozen 190.00
17 Stamp Pad Size 110 x 70 mm No. 35.00
18 Stamp Pad Size 157 x 96 mm No. 70.00
19 Stamp Pad ink 60 ml. No. 20.00
20 Gum Bottle 150 ml. No. 35.00
21 Stappler Machine HD-45 No. 90.00
22 Stappler pin 24/6 Box 250.00
23 Stappler no. 10 No. 125.00
24 Stappler no. 10 pin No. 40.00
25 Envelop 11" x 5" (1 set of 100 Nos. of envelop) Set 90.00
26 Envelop 9" x 4" (1 set of 100 Nos. of envelop) Set 65.00
27 Envelop 7" x 4" (1 set of 100 Nos. of envelop) Set 50.00
28 Natraj Pencile Box 40.00
29 Plastic folder (A4 size) No. 15.00
30 Box file No. 75.00
284
Approved
Sr. rates for
Particulars Unit
No. D.S.R. 2015-
16
1 2 3 4
31 Colour flag No. 25.00
32 Brown Envelop 18" x 12" jumbo size (1 bundle 50 Nos.) Bundle 200.00
33 Plastic folder (legal size) No. 15.00
34 Highlight pen (1 Box 5No.) Box 100.00
35 Ball pen Lexi (10 Nos./Box) Box 50.00
36 Folding Tapal Pad Dozen 300.00
37 Envelop 15" x 11" ledger Cloth (1 set of 5 Nos. of envelope) Set 150.00
38 White lace Bundle 70.00
39 Earser natraj Box 20.00
40 Envelop 18" x 11" ledger Cloth (1 set of 50 Nos. of envelope) No. 350.00
41 Plastic Tapal tray No. 250.00
42 Paper waight No. 25.00
43 Pin Container No. 30.00
44 White Board marker pen No. 25.00
Rulled Register Rounded leather (Ledger Lond Book) Make
45 quire 60.00
"Asman"
46 Computer paper legal size (Jk Brand) No. 220.00
47 Computer paper A4 size (Jk Brand) Pkt. 180.00
48 Fax Roll 30 mtr. Roll 70.00
Laser printer catrtridge toner No. ML-1010/1020/ML 1520/ML-
49 No. 4200.00
1710D/PMO 12 - H
50 Computer Disc (C.D.) No. 10.00
51 Re-writable C.D. No. 40.00
52 AntiVirus No. 1500.00
53 Cartridge Tonner Refil No. 400.00
285
ANNEXURE - C
Rates For Laundry Item
Sr. Approved rates for
Particulars Unit
No. D.S.R. 2015-16
1 2 3 4
1 Curtain - 5 x7 (Washing & Press) No. 80.00
2 Blancket - 4.5 x 6 (Washing) No. 100.00
3 Bed Sheet (Single) (Washing & Press) No. 40.00
4 Bed Sheet (Double) (Washing & Press) No. 70.00
5 Towel (Washing) No. 30.00
6 Napkeen (Washing) No. 15.00
7 Carpet - 10 x 10 (Washing) No. 200.00
8 Chadder (Washing) No. 50.00
286
THEORITICAL REQUIREMENT OF MATERIALS BUILDING
EXCAVATION
Sr. Item Unit Rubble in M3 Over size Sand in Quarry in
No. metal in M3 M3 spaul in
M3
1 Providing trap rubble M3 1.00 - - 0.20
soiling 15 to 20cm thick
2 Providing soiling using M3 1.00 0.15 -
80mm over size trap metal
PILE FOUNDATION
Sr. Item Unit Cement Sand in M3
No.
1 M-20 RCC cast in situ bored piles M3 8.00 bags 0.425
287
BRICK MASONARY
Sr. Item Unit Cement in Screened Bricks M.S. bars
No. bags sand in M3 in Nos in Kg.
288
Stone masonary
Sr. Item Unit Cement in Screened Trap Corner/ Remark
No. bags sand in M3 Rubble Quins in
in M3 Nos
1 UCR masonary in CM 1:6 in foundations 3 1.70 0.35 1.16 2
M
and plinth of inner walls/external walls
2 UCR masonary in CM 1:3 in basement M3 2.05 0.35 1.16 2
3 UCR masonary in CM 1:6 in Super 3 1.70 0.35 1.16 2
M
structure
4 Random rubble masonary in CM 1:6 in M3 1.70 0.35 1.16 2
foundation
5 Random rubble masonary in CM 1:6 in M3 1.70 0.35 1.16 2
Superstructure
6 Random rubble masonary 1st sort in CM M3 1.70 0.35 1.16 2
1:6 in external walls of plinth
7 Random rubble masonary 1st sort in CM M3 0.70 0.35 1.16 2
1:6 in Supersturcture
8 CR masonary 3rd sort in CM 1:6 in Plinth M2 1.70 0.35 1.16 2
289
WATER PROOFING TREATEMENT
Sr. Item Unit Cement Screened Course Aggreagate
No. in bags sand in M3
20mm in M3 12/10mm in M3
290
PAVING AND FLOORING
Sr. Item Unit Cement in bags Screened Sand in
No. M3
1 Rough shahabad flooring 25 to 30mm thick on bed of M2 0.135 0.022
1:6 CM with CP 1:3
2 Rough shahabad flooring 40 to 50mm thick on bed of M2 0.14 0.022
1:6 CM with CP 1:3
3 Rough shahabad flooring 50 to 60mm thick on bed of M2 0.15 0.022
1:6 CM with CP 1:3
4 Rough shahabad flooring 12 to 20mm thick on bed of M2 0.135 0.022
1:6 CM with CP 1:3
5 Polished shahabad/tandur/kotah stone flooring 25 to M2 0.135 0.022
30mm thick on bed of 1:6 CM
6 Polished shahabad/tandur/kotah stone flooring 25 to M2 0.135 0.022
30mm thick on bed of 1:6 CM with kadappa border
9 IPS flooring in 1:2:3 proportion 50mm thick M2 0.406 0.025 0.028 0.010
10 IPS flooring in 1:2:4 proportion 40mm thick M2 0.300 0.018 0.027 0.080
11 IPS flooring in 1:2:4 proportion 50mm thick M2 0.365 0.022 0.033 0.011
291
Sr. Item Unit Cement in bags Screened Sand in
No. M3
18 Coloured glazed tiles 150 x 150 mm for flooring on M2 0.20 0.02
bed of 1:4 CM
19 Coloured glazed tiles of 150 x 150 mm for dado on 1:4 M2 0.20 0.02
cement mortar plaster
20 Gray / White cement based marble mosaic tiles for M2 0.135 0.02
dado and skirting on 1:4 cement plaster
21 Gray / White cement base marble mosaic tiles for M2 0.185 0.02
dado and skirting on 1:4 cement plaster bed
27 P & L polished shahabad/ tandur kotah stone slab for M2 0.185 0.02
treads and risers on bed of 1:4 CM
28 Polished shahabad stone 40 to 50 mm for treads and M2 0.185 0.02
risers in CM 1:4
29 Plain cement tiles/plain coloured cement tiles for M2 0.185 0.02
treads and risers on bed of 1:4 CM
30 Marble mosaic tiles for treads and risers on bed of 1:4 M2 0.185 0.02
cement mortar
31 Marble slabs 20mm thick for treads and risers M2 0.185 0.02
32 Rough shahabad stone 40 to 50 mm for sills on bed of 2 0.185 0.02
M
1:4 CM
33 Polished shahabad tandur/kotah/kadappa stone 40 to M2 0.185 0.02
50 mm thick sill on bed of 1:4 CM
34 Providing sills of precast marble mosaic tiles on bed of M2 0.185 0.02
1:4 CM
35 White marble slabs dado and skirting M2 0.185 0.02
292
36 35mm thick precast polished chequered tiles / M2 0.16 0.02
coloured cement tiles and treads and plain cement
tiles for risers
37 Polished chequered marble mosaic tiles 20 x 32 cm M2 0.16 0.02
size for flooring / treads
38 Marble/Kadappa/tandur stone partition for urinals M2 0.05 0.005
39 White glazed tiles / colour glazed tiles of 200 x 100mm 2 0.22 0.02
M
for flooring on 1: 4 CM
40 White glazed / colour glazed tiles of 200 x 100mm for M2 0.21 0.02
dado and skirting
Bd - W. Miscellaneous
Sr. Item Unit Cement in Screened Crushed metal
No. bags sand in 12/10mm in M3
M3
1 Guiniting by dry mix process in 1:3 1/2 CM for ceiling
(A) and soffit
a) 20mm thick M2 0.23 0.028 -
b) 25mm thick M2 0.29 0.035 -
c) 40mm thick M2 0.46 0.056 -
d) 50mm thick M2 0.576 0.070 -
a) 20mm thick M2 - - -
b) 25mm thick M2 0.256 0.034 -
c) 40mm thick M2 0.444 0.054 -
d) 50mm thick M2 0.550 0.067 -
293
2 P & E 1.50m high wire fencing wire fencing with 7 M 0.132 0.018 0.036
rows of bar bed wire fencing with MS angles at 2.50 M
c/c in cc 1:4:8 blocks of 45 x 45 x 45cm
3 P & E 1.50m high wire fencing wire fencing with 7 M 0.132 0.018 0.036
rows of bar bed wire fencing with wooden round
bullies
4 P & E chain line fencing with CC 1:4:8 blocks of 45 x M 0.310 0.042 0.085
45 x 45cm at 1.75m c/c
1 Water meter chamber in brick masonary with cement No. 0.52 0.103 134 0.025
plaster 15mm dia to 100mm dia
2 45cm wide steel ladder with CC 1:2:4 block of 60 x 30 No. 0.35 0.024 - 0.048
x 30 cm
294
Sr. Item Unit Cement in bags
No.
19 Cast iron rain water pipe 75/100/150mm dia M 0.003
20 Asbestos cement rain water pipe 100/150mm dia M 0.005
21 Cast iron soil/waste water/vent pipe of 80/100/150mm dia M 0.007
22 Asbestos cement soil/waste water/vent pipe of 75/100/150 mm dia M 0.007
295
THEORITICAL REQUIREMENT OF MATERIALS OF BLACK TOP ROAD ITEMS
(AS PER STANDARD SPECIFICATIONS)
Sr. Item Unit Asphalt in Kg Coarse Aggregate
No 40mm in 25mm 20mm 12mm 10mm 6mm
m3 in m3 in m3 in m3 in m3 in m3
1 Providing 50mm thick full grout 100 M2 Dose 500.00 6.00 - - 1.50 1.20 -
with seal coat Seal coat 125.00
Total 625.00
2 Providing 50mm thick semi frout 100 M2 Dose 275.00 6.00 - - 1.50 1.20 -
with seal coat Seal coat 125.00
Total 400.00
3 Providing 40mm thick premix 100 M2 304 - 2.45 - 2.73 - 0.60
carpet
4 Providing 25mm thick premix 100 M2 205 - - 1.85 - 1.20 0.60
carpet
5 Providing 20mm thick premix 100 M2 156 - - - 1.83 0.90 0.15
carpet
6 Single coat surface dressing on 100 M2 200 - - - 1.50 - -
WBM surface
7 Single coat surface dressing on 100 M2 125 - - - 1.05 - -
BT surface
8 Two coat surface dressing 100 M2 Dose 225.00 - - - 1.80 1.00 -
Seal coat 125.00
Total 350.00
9 Bituminious liquid seal coat 2 98 - - - - - 0.90
100 M
10 50mm thick special grout 100 M2 Tack coat 73.50 - - - 1.80 0.90 -
bituminious surface including Dose 40.00
tack coat and seal coat Seal coat 97.50
Total 611.00
11 Tack coat on WBM surface 100 M2 100 - - - - - -
12 Tack coat on BT surface 2 50 - - - - - -
100 M
13 Emulsion tack coat on WBM 100 M2 35 - - - - - -
surface
14 Emulsion tack coat on BT 100 M2 25 - - - - - -
surface
15 25mm thick hot mix hot laid 100 M2 209 - - 1.85 - 1.20 0.60
carpet
16 20mm thick hot mix laid 100 M2 146 - - 1.83 - 0.90 0.15
carpet(open graded premix
carpet)
HB Metal
40mm in
M3
17 a) 75mm thick bituminious bound 100 M2 250 9.00 - 1.5 1.80 - -
macadam surface on BT surface
296
THEORITICAL MATERIAL REQUIREMENT
AS PER STANDARD SPECIFICATIONS
(REQUIREMENT OF MATERIALS SHALL BE AS PER ACTUAL JOB MIX
BRIDGE AND C.D. WORKS
Sr. Item Unit Cement Screened Course Aggreagate
No. in bags sand in
M3 40mm in 20mm in 12/10m
M3 M3 m in M3
1 Plain cement concrete 1:5:10 M3 2.60 0.47 0.94 - -
2 Plain cement concrete 1:4:8 3 3.40 0.47 0.94 - -
M
3 Plain cement concrete 1:3:6 3 4.40 0.47 0.70 0.24 -
M
4 Plain cement concrete 1:2:4 3 6.40 0.445 - 0.67 0.22
M
5 M-10 grade concrete 3 4.40 0.47 0.70 0.24 -
M
6 M-15 grade concrete 3 6.00 0.445 - 0.67 0.22
M
7 M-20 grade concrete 3 7.00 0.445 - 0.67 0.22
M
8 M-25 grade concrete 3 7.50 0.445 - 0.67 0.22
M
9 M-30 grade concrete 3 8.00 0.425 - 0.57 0.28
M
10 M-35 grade concrete 3 8.25 0.47 - 0.57 0.28
M
11 Cast in situ abutment and piers in 3 4.40 0.47 0.70 0.57 -
M
M-10
12 Cast in situ abutment and piers in 3 6.00 0.47 0.70 0.24 -
M
M-15
13 Cast in situ abutment and piers in 3 7.00 0.47 0.70 0.24 -
M
M-20
14 Cast in situ abutment and piers in 3 3.90 0.40 0.55 0.24 0.15
M
M-10 with 15% plum
15 Cast in situ abutment and piers in 3 5.80 0.40 0.55 0.24 0.15
M
M-15 with 15% plum
297
RCC PIPES
Sr. Item Unit Cement Sand in Weight of pipe in
No. in bags M3 kg./m.
NP-2 NP-3
pipes pipes
1 P & L cc pipes of NP-2
class/ IRC pipes of NP-3
class
i) 80mm ∅ M - - 20 -
ii) 100mm ∅ M - - 24 -
iii) 150mm ∅ M - - 33 -
iv) 250mm ∅ M - - 52 -
v) 300mm ∅ M - - 75 -
vi) 350mm ∅ M - - 92 240
vii) 400mm ∅ M - - 104 269
viii) 450mm ∅ M 0.12 0.009 128 297
ix) 500mm ∅ M - - 141 325
x) 600mm ∅ M 0.16 0.011 193 410
xi) 700mm ∅ M - - 223 470
xii) 800mm ∅ M 0.188 0.012 287 604
xiii) 900mm ∅ M 0.22 0.0154 358 754
xiv) 1000mm ∅ M 0.25 0.017 438 829
xv) 1100mm ∅ M - - 525 1054
298
THEORITICAL MATERIAL REQUIREMENT
M.O.S.T. 2013 EDITION AND DATA BOOK
(Grading Mateial shall be as per actual job mix formula wherever applicable)
299
3C) Bituminous macadam with 3% bitumen by weight
of total mix
A) (E l di
Bitumen i /t k t)
66 Kg/M3
B) Coarse aggregate 11.20 to 0.835 M3
26.40mm
C) Chipping 2.80 to 11.20mm 3
0.209 M
D) Fine aggregate Below 2.80mm 0.366 M3
Total 1.380 M3
2 3 2 2
75mm ---- 20.00Kg/10M 0.90 M /10 m 0.18 M3 /10 m
300
7 A) Surface dressing (Table 500.13 page 170)
Bitumen Stone chipping
i) Single coat surface dressing or 1st coat
of two coat surface dressing
10 mm size
2
i) Over B.T. Surface 27.50 kg/10m 0.105 m3 / 10 m2
12 mm size
ii) Over B.T. W.B.M. 20.00 kg/10m2 0.15 m3/102
i) Single coat surface dressing or 1st coat 12 to 14 Kg/10M2 0.10 to 0.12 M3/10M2
of two coat surface dressing
10 mm size
2
i) Ist Coat 22.50 kg/10 m 0.18 m3 /10m2
12 mm size
ii) IInd Coat 12.50 kg/10 m2 0.10 m3 / 10m2
8) Open graded premix carpet 20mm thick (Table 500.16 Page 178) Clause no. 509
i) 13.20mm Nominal size 3 2
0.18 M /10M
ii) 11.20mm Nominal size 0.09 M /10M2
3
9) Mix seal surfacing (Excluding tack coat) Data book clauseno. 510
301
10) Bituminous Concrete (Excluding primer /tack coat with cement filler)
Density 2.40 Data Book bitumen content at 6.50 %
12) P & L semidense bituminous concrete with 5.50% Bitumen Clause No. 511
(Excluding primer/tack coat)
13) Providing and applying premixed seal coat type ''B'' Clause no. 513
302
THEORITICAL MATERIAL REQUIREMENT
M.O.S.T. 2013 EDITION AND DATA BOOK
(REQUIREMENT OF MATERIALS SHALL BE AS PER ACTUAL JOB MIX
BRIDGES AND CULVERTS
Sr. Item Unit Cement Coarse Course Aggreagate
No. of in MT Sand in
Data M3 40mm 20mm 10mm
book in M3 in M3 in M3
2.3 (i) PCC / RCC in open
foundation
a) PCC M-25 grade 3 0.40 0.365 0.382 0.304 0.294
M
b) PCC M-30 grade 3 0.42 0.365 0.382 0.299 0.304
M
c) RCC M-35 grade 3 0.475 0.40 - 0.57 0.28
M
d) RCC M-40 grade 3 0.50 0.40 - 0.57 0.28
M
2.3 (ii) a) PCC M-15 3 0.33 0.45 0.52 0.22 0.11
M
b) i) PCC M-20 3 0.38 0.45 0.57 0.22 0.11
M
c) ii) RCC M-20 3 0.40 0.425 - 0.57 0.28
M
c) RCC M-25 3 0.41 0.45 - 0.63 0.27
M
2.5 (i) a) PCC/RCC Well Curb
i) RCC M-35 grade M3 0.475 0.40 - 0.57 0.28
ii) RCC M-40 grade 3 0.50 0.40 - 0.57 0.28
M
b) Well Steining
i) PCC M-25 grade M3 0.40 0.365 0.382 0.304 0.294
ii) PCC M-30 grade 3 0.42 0.365 0.382 0.304 0.299
M
iii) RCC M-35 grade 3 0.475 0.40 - 0.57 0.28
M
iv) RCC M-40 grade 3 0.50 0.40 - 0.57 0.28
M
c) Bottom Plug M-25 3 0.44 0.365 0.382 0.304 0.299
M
(includin
g 10%
extra)
d) Top & Intermidiate plug in M3 0.40 0.365 0.382 0.304 0.294
. PCC M-25
e) Well cap in RCC M-35 3 0.46 0.365 0.382 0.304 0.299
M
2.5 (ii) a) Well curb
i) RCC M-20 3 0.40 0.425 - 0.57 0.28
M
ii) RCC M-25 3 0.41 0.45 - 0.63 0.27
M
303
b) Well Steining
b) i) PCC M-15 M3 0.33 0.45 0.52 0.22 0.11
c) ii) a) PCC M-20 3 0.38 0.45 0.57 0.22 0.11
M
c) iii) b) RCC M-20 3 0.40 0.425 - 0.57 0.28
M
b) iii) RCC M-25 3 0.41 0.45 - 0.63 0.27
M
c) Bottom Plug
PCC M-20 gfrade M3 0.418 0.45 0.57 0.22 0.11
(includin
g 10%
extra)
d) Top & Intermediate plug
PCC M-15 M3 0.33 0.45 0.52 0.22 0.11
e) Well cap
i) RCC M-20 grade M3 0.38 0.45 0.57 0.22 0.11
ii) RCC M-25 grade 3 0.40 0.365 0.382 0.304 0.299
M
iii) RCC M-30 grade 3 0.42 0.365 0.382 0.304 0.299
M
3.3 a) PCC/RCC for sub
structure
i) PCC M-25 grade 3 0.40 0.365 0.382 0.304 0.299
M
ii) PCC M-30 grade 3 0.42 0.365 0.382 0.299 0.304
M
iii) RCC M-35 grade 3 0.46 0.365 0.382 0.304 0.299
M
iv) RCC M-40 grade 3 0.50 0.40 - 0.57 0.28
M
b) PCC/RCC for sub
i) PCC M-15 grade M3 0.33 0.45 0.52 0.22 0.11
ii) PCC M-20 grade 3 0.38 0.45 0.57 0.22 0.11
M
iii) RCC M-20 grade 3 0.40 0.425 - 0.57 0.28
M
iv) RCC M-30 grade 3 0.41 0.45 - 0.63 0.27
M
v) RCC M-30 grade 3 0.45 0.43 - 0.58 0.28
M
4.1 i) RCC Superstructure
a) RCC M-35 grade M3 0.475 0.40 - 0.57 0.28
b) RCC M-40 grade 3 0.50 0.40 - 0.57 0.28
M
ii) a) RCC M-25 grade 3 0.41 0.45 - 0.63 0.27
M
b) RCC M-30 grade 3 0.45 0.43 - 0.58 0.28
M
304
4.2 Prestressed concrete
a) M-35 grade M3 0.475 0.40 - 0.57 0.28
b) M-40 grade 3 0.50 0.40 - 0.57 0.28
M
c) M-45 grade 3 0.52 0.40 - 0.57 0.28
M
d) M-50 grade 3 0.54 0.40 - 0.57 0.28
M
4.13 PCC Leveling coarse of M-15 3 0.33 0.45 0.52 0.22 0.11
M
below approach slab
Culverts
PCC 1:4:8 M3 0.17 0.47 0.89 - -
PCC 1:3:6 3 0.22 0.47 0.89 - -
M
PCC M-15 grade 3 0.33 0.45 - 0.85 -
M
PCC M-20 grade 3 0.40 0.425 - 0.95 -
M
305
ABBREVIATIONS
1 Square Kilometre Sq.Km.
2 Kilogram Kg.
3 Metric tonne M.T.
4 Number No.
5 Runing metre R.M.
6 Cubic centimeter Cu.Cm.
7 Milimetre mm.
8 Centimeter Cm.
9 Metre M.
10 Kilometre Km.
11 Square Metre Sq.M.
12 Cubic Metre Cu.M.
13 Ministry of Road Transport & Highway MORT&H
14 Indian Standard IS
15 Indian Road Congress IRC
16 Tools and Plants T&P
17 Galvanised Iron GI
18 Cast Iron CI
19 Reinforced Cement Concrete RCC
20 Plain Cement Concrete PCC
21 Pre-Stressed Concrete PSC
22 Ready Mixed Concrete RMC
23 Ground Level GL
24 Rupees Rs.
25 Diametre Dia
26 Minimum Min
27 Maximum Max
28 Hour Hr
29 That is i.e.
30 For Example e.g.
31 Water Bound Macadam W.B.M.
32 Bituminous Macadam BM
33 Lead in Kilometre L
34 Optimum Moisture content O.M.C.
35 Hot mix, hot laid H.M.H.L.
306
36 Building Works Bd.
37 Bridge Works Br.
38 Cross Drainage Cd
39 Road Works Rd.
40 Taluka Tal.
41 District Dist.
42 Country Cut Teak Wood C.C.T.W.
43 Centre to Centre c/c
44 Mild Steel M.S.
45 High Yield Strength Deformed Bar H.Y.S.D.
46 Unplasticized Poly Venyl Chloride UPVC
47 Poly Venly Chloride P.V.C.
48 Asbestos Cement A.C.
49 Cement Mortar C.M.
50 Expanded Mesh XPM
51 Boiling Water Proof BWP
52 Boring B'NG
53 Survey Works (Departmental Agency) Survey-D
54 Survey Works (Private Agency) Survey-P
307
GOVERNMENT OF MAHARASTARA
Vigilance & Quality Control Circle
Schedule of Testing charges for construction material used for Government
Works for the Year 2015-16
Effective from 1/ 08/2015
308
GLAZED TILES
17 Water Absorption(Set of 6 Tiles), Modulus of Rupture ( 1 Test 1300.00
Set of 6 Tiles)
18 Determination of Impact Resistance. 1 Test 600.00
CERAMIC TILES / VITRIFIED TILES
19 Water Absorption, Moduls of Rapture (Set of 6 Tiles) 1 Test 1300.00
MANGLORE TILES
23 Water Absorption (Set of 6 Tiles), Flexural test (Set of 6 1 Test 1200.00
Tiles).
24 Permeability. 1 Test 800.00
CONCRETE
25 Compressive Strength OF C.C. Cube(Set of 3 cubes). 1 Test 550.00
26 Concrete Mix Design (With all Tests on basic materials)* 1 Test 11000.00
SOIL / MURUM
35 Sieve Analysis. 1 Test 550.00
36 Field moisture Content. 1 Test 350.00
37 Liquid limit & plastic Limit. 1 Test 900.00
38 Compaction Test ( Proctor Density ). 1 Test 1500.00
39 C.B.R. Test ( Lab ) Excluding compaction test. 1 Test 5500.00
40 C.B.R. Test ( Field Determination Test) Excluding 1 Test 2100.00
Transportations per IS 2720 Part XXXI
41 Dead Journey Charges,inspection Vehical per km. 15.00
42 Dead Journey Charges,Truck/Tipper per km. 54.00
309
43 Field Density by Sand replacement method. 1 Test 900.00
44 Sulphate & Chloride Contents. 1 Test 650.00
45 Mechanical Analysis. 1 Test 1800.00
46 Plate Load Bearing Test. (Excluding Transportation) 1 Test 25000.00
47 Free Swell Test for Soil 1 Test 750.00
BITUMEN
48 Penetration, Softening Point, Flash & Fire Point, Specific 1 Test 2500.00
Gravity
49 Viscosity. 1 Test 1550.00
50 Ducility / Elastic Recovery 1 Test 750.00
51 Extraction Test. 1 Test 1300.00
52 Sieve Analysis of Bituminous mix(2 samples of extraction 1 Test 3150.00
for one sieve analysis excluding extraction)
53 Marshall Stability & Flow measurement. (Set of 3 moulds) 1 Test 800.00
55 Job Mix Design with all Tests on basic material for 1 mix 13000.00
DBM/SDBC/AC. design
56 B. M. Job Mix Design ( Preparation of Marshall Mould & 1 Test 6000.00
Density ).
57 Mastic Hardness No. 1 mix 550.00
design
58 Thin film oven test & test on residue of modified bitumen. 1 Test 2500.00
310
PLYWOOD
72 Determination of Resistance to dry heat, Determination of 1 Test 2700.00
Moisture Content, Determination of Density, Thickness of
Plywood,
73 Test for Glue Adhesion 1 Test 450.00
PARTICAL BOARD
74 Determination of Moisture Content, Determination of 1 Test 1300.00
Density
ALUMINIUM SECTION
75 Thickness, Mass Per Running meter 1 Test 550.00
Test on Powder Coating 1 Test 650.00
POLYMER MATERIAL
76 PH Value, Solid Content 1 Test 750.00
A.C. PIPES
77 Water Absorption 1 Test 550.00
78 Bursting Strength 1 Test 400.00
A.C. SHEETS
79 Water Absorption, 1 Test 550.00
80 Load Bearing 1 Test 300.00
G.I. PIPES
81 Weight per running meter, Diameter of pipe & wall 1 Test 200.00
thickness of pipe,
82 Weight of Zinc coating per sq. m. 1 Test 250.00
P.V.C. PIPES (NONPLASTISIZED)
83 Weight per running meter, Diameter of pipe & wall 1 Test 200.00
thickness of pipe
STEEL ANTI CORROSIVE TEST
84 Resistance to applied Voltage. ( 1 Hr. Test ) (Set of 2 1 Test 900.00
Bars)
85 Resistance to applied Voltage.( 30 Days Test ) (Set of 2 1 Test 2500.00
Bars )
86 Thickness of Coating. (Set of 2 Bars) 1 Test 450.00
87 Chemical Resistance Test.( Set of 8 Bars ) 1 Test 1900.00
88 Hardness of Coating Test . 1 Test 250.00
89 Salt Spray Test ( 4 Cycles ) ( Set of 2 Bars ) 1 Test 1200.00
STEEL BAR TESTING
90 Upto 16 mm (Set of 3 Bars) 1 Test 1000.00
91 Above 16 mm (Set of 3 Bars) (Tensile strength, %, 1 Test 1300.00
Elongation, Yield Stress, Weight-Per Meter, Bend /
Rebend Test, Proof Stress.)
92 Nitrol Solution Test. (Set of 3 Bars) 1 Test 3100.00
311
PAINT / THERMO-PLASTIC PAINT
93 Glass bead contents & grading analysis. 1 Test 3100.00
94 Reflectance & yellowness index. 1 Test 900.00
95 Flowability.(Percentage residue). 1 Test 800.00
96 Softening Point. (Ring & ball method). 1 Test 800.00
97 Drying Time. 1 Test 650.00
COAL TAR EPOXY PAINT
98 Drying Time. 1 Test 650.00
99 Dry Film Thickness. 1 Test 600.00
100 Flexibility. 1 Test 250.00
101 Gel Time. 1 Test 400.00
102 Pot Life. 1 Test 400.00
103 Volume of Solid. 1 Test 850.00
ROAD SIGN BOARD
104 Retro Reflective Test. 1 Test 3200.00
ROUGHNESS INDEX / ROAD UN-EVENNESS TEST
105 Road Surface Single Lane.(3.70 to 5.50 m) per km. 600.00
106 Road Surface 1.5 Lane to Two Lane.(5.50 to 7.00 m) per km. 1200.00
107 Each Additional Lane. per km. 600.00
108 Dead Journey Charges. per km. 15.00
OVERLAY DESIGN
109 Benkelman Beam Test (Excluding Dead Journey per km 11300.00
Charges)
NON -DESTRUCTIVE TEST
110 Rebound Hammer Test. 1 point 150.00
111 Ultrasonic Pulse Velocity 1 point 250.00
Important Note : The above rates are applicable for all Division & Subdivision under P.W.D. &
Z.P. in Maharashtra and for other Govertment / Private Organization the rates shall be twice as
mentioned in DSR.
Suprintending Engineer
Vigilance & Quality Control Circle,
Pune
312
Assistant Research Officer
Regional Laboratory
P.W.Compound, Turbhe,
New Mumbai (ISO 9002 Certified)
Tel. 022/7682541 / Ext. 33
Control Tests & their frequency & specified limits for various construction materials
2 SAND
1) Particle size. 100% passing through 4.75 mm
I.S. sieve
2) Silt content. Not more than 4%
3) Fineness modulus. 1) For concrete 2.6 to 3.6 Tests should be carried out in
2)For masonry and 1st coat of the beginning and if there is a
plaster. Not more than 3. change in source
3) For pointing & IInd coat of
plaster shall Not exceed 1.6
4) Bulkage. Bulkage will have to be
determined for applying
correction to the qty. of sand as
and when necessary.
313
5) Moisture content. Will have to be determined to find
quantity of free water in sand.
3 COARSE AGGREGATE
1) Gradation.
Size of metal. 100 % 100% Retained on
Passing sieve size
through
sieve size
80 mm. 100mm 50 mm One test for per 100 Cubic
metre
60mm 80mm 50 mm
50mm 60mm 40 mm
40mm 63mm 63 mm (0%)
40mm 35 40mm (30 to 65%)
to 70%
12.5mm 0 12.5mm (95 to 100%)
to 5 %
40mm to50mm. 63 mm 25 mm
314
7) Specific Gravity Not Not specified
specified
4 BRICKS I class II class
1 )Water absorption shall not 20% 22%
exceed
2)Compressive Strength (wet 32.8 29.52 kg/cm2 A set of 15 bricks for 50000
condition ) kg/cm2 minimum consignment or part there of.
minimum
3)Efflorescence NIL - when there is no
perceptible deposit of
efflorescence
Slight – when not more than
10% area is covered with
deposit
Serious – when there is heavy
deposit of salt accompanied by
powdering or flaking of surface
315
110 90(420x250)
(420x250)
110 90(425x260)
(425x260)
Individual Individual
90 68(410x235)
(410x235)
9 SOIL / MURUM
1. Proctor Density Shall not 1.52 gm/cc for Embankment upto One test per 1000 m3 or soil.
be less than 3 mtr. Height
1.6 gm/cc for subgrade and
earthen shoulders/verges/backfill.
10 HARD MURUM
1)Gradation 95% passing through 80 mm One test for compaction of 1
seive size 2% passing through 25 layer in one km. and every
mm seive size change in source or type of
2) Plasticity Index Below 4 murum.
11 SOFT MURUM
1) Plasticity Index Below 8 One test for compaction of 1
layer in one km. and every
change in source or type of
murum.
12 STONE
Water Absorption Maximum 5%
316
Compressive Strength 1530 kg/cm2
Specific Gravity Not less than 3
13 GLAZED TILES
1) Water Absorption Not more than 18% One set of 5 tiles for every
5000 tiles or part thereof.
14 BITUMEN
1) Penetration To ascertaion the Two samples per lot to be
correct grade of subjected to all some tests as
bitumen directed by the Engineer.
15 BITUMINOUS MIX
1) Extraction To check correct binder content 2 test for each 100 tonnes of
as per the tender mix subject to a minimum of
two tests per day per plant.
Minimum stability 820 kg for
SDBC
2) Marshall Stability & Flow SDBCMinimum stability 900 kg For each 100 tonnes of mix
measurments for DBM/BC produced , a set of 3 marshall
moulds to be prepared and
tested as per MOST
Flow 2-4 mm
317
ADDITIONAL TESTS CONDUCTED AT REGIONAL LABORATORY AT TURBHE NEW MUMBAI AND DISTRICT
LABORATORIES AT MANGAON AND RATNAGIRI
CONTROL TESTS AND THEIR FEQUENCY AND SPECIFIED LIMITS FOR VARIOUS CONSTRUCTION MATERIALS
Sr. Material & Tests Specified Limit Frequency
No.
1 COARSE AGGREGATE
1 Soundness Loss with Before approving the aggregates
Sodium – 12% Max. and every month subsequently
Magnesium Sulphate 18% Max.
2 Bulk Density - -
FINE AGGREGATE
3 CL2 & Sulphate Content Sulphate content – 500 mg/Lt
4 Moisture Content Cl 2 content –
2000 mg/Lt. – For P.C.C.
5 Bulkage of sand 1000 mg/Lt. – For R.C.C.
BITUMEN GRADE
9 Softening point 30/40 60/70 80/100 2 sample /lot to be subjected to all
50-65 40-55 35-50 or some tests as directed by the
Engineers.
10 Viscosity
11 Flash & fire point (Minimum ) min 175 min 175 min 175
318
14 Mastic Hardness No. 0
60 to 80 at 25 C without coarse
aggregate
10 to 20 at 250C after adding coarse
aggregate
WATER
15 PH value Not less than 6 Once for approval of source of
supply subsequently in case of
doubt
16 Sulphate & Chloride content Sulphate content – 500 mg/Lt
Chloride content –
2000 mg/Lt. for P.C.C.
1000 mg/Lt. for R.C.C.
WOOD
17 Density At least 3 samples from lots
containing upto 200 pieces
18 Moisture content Roof and floors/weather
Boards 20%
Joinery beams/staircase 16% floors
12%
STEEL ANTICORROSIVE
TEST
19 Resistance to applied There was no sign of any coating -
voltage (1 Hr.test) failure at cathode, due to evaluation
of hydrogen gas of any lasting at
anode
20 Resistance to applied No under cutting of coating shall -
voltage (30 days.test) occur at any holiday that develops
during testing. If no holiday
developed during 30 days single
intentional hole of 6 mm. shall be
made in both cathod in anode then
test shall be continued for additional
24 hours in which no under cutting
shall occur
21 Thickness of coating Minimum thickness Coating thickness shall be tested at
CECRI – 200 – 400 Mic. a frequency of not less than one full
FBEC – 100 – 300 Mic. length bar every twenty bars for
CPCC – 125 Mic. Min each size.
22 Chemical resistance Test The coating shall not blister, soften, -
lose bond, nor development holiday
during 45 days. The intentionally
made holes shall exhibit no under
cutting during the 45 days period.
23 Hardness of coating Test Hardness of coating when measured -
using a pencil hardness tester shall
be around 54 to 74.
319
320