1
853 new.qxd 3/15/2004 12:44 PM Page 2
EMERGENCY OVERRIDE
If the optional starter defeat is installed and
your remote is lost or fails to operate, you
can manually override the starter defeat.
2
853 new.qxd 3/15/2004 12:44 PM Page 3
INSTALLATION INSTRUCTIONS
Before you begin the installation: required. For vehicle’s with independent left
• This product must be installed by qualified and right parking light circuits, the parking
personnel according to these instructions. light wires must be connected using diodes
• Verify with the customer the desired to keep the circuits separate.
location for the program switch and LED. • WIRE - Unlock #87 normally open input
• Always use a multimeter when verifying 10A fuse. (see Door Lock Wiring Diagrams)
vehicle wiring. • BLUE/BLACK WIRE - Unlock #30
common output. (see Door Lock Wiring
Installation Notes: Diagrams)
• Do not install the main unit in the engine • BROWN/BLACK WIRE - Unlock #87A
compartment. normally closed input. (see Door Lock Wiring
• Make all wiring connections to the vehicle Diagrams)
before connecting the main 15-pin • VIOLET/BLACK WIRE - Lock #87
connector harness to the main unit. normally open input 10A fuse. (see Door Lock
• Mount the main unit in a secure area, away Wiring Diagrams)
from vehicle computers and heating/air • GREEN/BLACK WIRE - Lock #30
conditioning ducts. Mount the unit as far common output. (see Door Lock Wiring
away from metal objects as possible to Diagrams)
increase the range of the remote • WHITE/BLACK WIRE - Lock #87A
transmitters. normally closed input. (see Door Lock Wiring
• When running the harness wires through Diagrams)
the vehicle, be careful to run them where • ORANGE WIRE - Armed Output (-)
they cannot be damaged or shorted. Keep 500Ma. The ORANGE wire provides ground
them away from any moving parts or areas of when the unit is armed to activate a starter
high heat. Use rubber or plastic grommets to disable relay. Connect to a relay for starter
protect the harness wires where they pass defeat.. (See Relay Wiring Diagrams)
through holes in metal panels.
• BLACK/YELLOW - Dome light output (-)
Main Harness: 500mA. Connect to a relay to activate the
dome light when the system is unlocked. (See
• BLACK WIRE - Ground input (-). Connect to Relay Wiring Diagrams)
a solid chassis ground that is clean and free
of paint or dirt. • GRAY WIRE - Auxiliary output (-) 500mA.
Connect to a relay for optional trunk release
• RED WIRE - +12V battery input. etc. (See Relay Wiring Diagrams)
• WHITE WIRE - Parking light output (+). • BROWN WIRE - Horn honk output (-)
Connect to the wire that shows +12V when 500mA. Connect to a relay to honk the
the parking lights are on. If the vehicle’s vehicle’s horn. (See Relay Wiring Diagrams)
parking light circuit exceeds 10A, a relay is
3
853 new.qxd 3/15/2004 12:44 PM Page 4
• BLUE/WHITE WIRE - Passenger unlock 3. Press the valet switch the number times
output (-) 500mA. The BLUE/WHITE wire equal to the desired feature.
provides a ground to unlock the passenger • The horn will chirp and lights/LED will
doors when the unlock button on the flash, each time the valet switch is
transmitter is pressed two times. To install pressed.
the two-step unlock feature, the 4. Within 5 seconds, press the transmitter
BLUE/BLACK and BROWN/BLACK wires button corresponding to the desired
must be run directly to the driver’s door operating mode for that feature.
actuator unlock wire and the BLUE/WHITE • The horn will chirp and lights will flash
wire must be connected to a relay to unlock to indicate the setting.
the passenger doors. (see Optional Two-Step
Unlock Diagrams) One chirp/flash = Button 1
• YELLOW WIRE - Ignition input (+). Two chirps/flashes = Button 2
Connect to the main ignition wire that 5. Turn off ignition to save changes.
switches +12V and does not drop out during
cranking. FEATURE DESCRIPTION
1. Ignition Lock/Unlock. Automatically
2-Pin Red Connector: Plug-in connector locks the doors when the ignition is turned
port for LED. Mount LED in an area where on and unlocks when the ignition is turned
it may be easily seen from either side of the off.
vehicle. 2. Door Unlock Pulse. Selects between a
2-Pin Blue Connector: Plug-in connector single or double unlock pulse.
port for program/service switch. Mount 3. Chirp Mode. Selects or bypasses the
program switch in an area that is easily system’s lock’unlock confirmation chirps.
accessible from the driver’s position. 4. Door Lock PulseLength. Selects
between a .75-second or 3-second
PROGRAMMABLE FEATURES
lock/unlock pulse.
To enter program mode: 5. Passive Starter Defeat. Enables the
1. Turn on ignition. starter defeat to automatically activate 45
2. Within 5 seconds, press valet switch 5 seconds after turning off the ignition.
times. 6. Ignition Trigger. Enables the ignition
• The horn will provide a long chirp, to trigger feature when the system is remotely
indicate entering program mode. locked.
4
853 new.qxd 3/15/2004 12:44 PM Page 5
5
853 new.qxd 3/15/2004 12:44 PM Page 6
VIOLET VIOLET
BLUE/BLACK BLUE/BLACK
HARNESS
HARNESS
BROWN/BLACK BROWN/BLACK
VIOLET/BLACK VIOLET/BLACK
GREEN/BLACK GREEN/BLACK
NOT USED NOT USED
WHITE/BLACK WHITE/BLACK
NOT USED NOT USED
CONNECT
TO +12V
VIOLET VIOLET
BLUE/BLACK BLUE/BLACK
HARNESS
HARNESS
BROWN/BLACK BROWN/BLACK
VIOLET/BLACK
GREEN/BLACK
VIOLET/BLACK
GREEN/BLACK XCUT
WHITE/BLACK WHITE/BLACK
L
CONNECT AFTER-MARKET
TO +12V ACTUATORS UL
LOCK/UNLOCK
SWITCH
CONNECT
TO +12V L
UL
VIOLET
BLUE/BLACK
X CUT LOCK/UNLOCK
SWITCH
HARNESS
BROWN/BLACK
VIOLET/BLACK
GREEN/BLACK
WHITE/BLACK
CUT
X FACTORY DOOR
MOTOR
6
853 new.qxd 3/15/2004 12:44 PM Page 7
CONNECT
(-) DOOR LOCK
L TO +12V
(+) DOOR LOCK
(-) DOOR UNLOCK 87 L
UL (+) DOOR UNLOCK
BLUE/WHITE BLUE/WHITE 87a UL
86 85
LOCK/UNLOCK 30
CONNECT SWITCH
TO +12V LOCK/UNLOCK
CONNECT SWITCH
FACTORY DOOR TO +12V
VIOLET
BLUE/BLACK LOCK MODULE VIOLET FACTORY DOOR
LOCK MODULE
HARNESS
BROWN/BLACK BLUE/BLACK
HARNESS
VIOLET/BLACK BROWN/BLACK
GREEN/BLACK CUT
X VIOLET/BLACK
WHITE/BLACK GREEN/BLACK CUT
X
WHITE/BLACK
30 30
X
CUT PASSENGER DOOR
MOTORS
VIOLET
BLUE/BLACK
HARNESS
BROWN/BLACK
CONNECT VIOLET/BLACK
TO +12V GREEN/BLACK
WHITE/BLACK
VIOLET
BLUE/BLACK DRIVER'S DOOR
HARNESS
BROWN/BLACK ACTUATOR
VIOLET/BLACK
X
CONNECT
CUT
GREEN/BLACK TO +12V
WHITE/BLACK DRIVER'S DOOR
MOTOR
7
853 new.qxd 3/15/2004 12:44 PM Page 8
LED
87 87
HORN OR DOME CONNECT HORN OR DOME
LIGHT OUTPUT 87a LIGHT OUTPUT
TO +12V 87a
FROM ALARM 86 85 FROM ALARM 86 85
30 30
CONNECT
TO +12V