The licensing MO instance name is csfbTo1xRtt. The CS fallback for emergency call
is also supported. The existing license EcsCsfb to control the emergency call
support shall be enabled to control the CSFB for emergency call.
Table 16
Type of change
MOC name
Description
New
ExternalCdma20001xRttCell
New
Cdma20001xRttBandRelation
New
Cdma20001xRttFreqRelation
New
Cdma20001xRttCellRelation
Modified
ExternalCdma2000Cell
Table 17
Type of change
Attribute name
MOC name
Description
Range
Resolution
Unit
Default value
New
bandClassPrioListCDMA1xRtt
RATFreqPrio
N/A
N/A
N/A
N/A
New
cdma2000FreqBandRef
Cdma20001xRttBandRelation
N/A
N/A
N/A
New
Cdma20001xRttBandRelationId
Cdma20001xRttBandRelation
N/A
N/A
N/A
New
cellReselectionPriority
Cdma20001xRttBandRelation
0..7
N/A
New
threshXHigh1xRtt
Cdma20001xRttBandRelation
Threshold used in reselection towards a high priority CDMA2000 1xRTT band class,
expressed as an unsigned binary number equal to FLOOR ([-2 x 10 x log10 Ec/Io]) in
units of 0.5 dB If sNonServingCell > threshXHigh1xRtt, reselection is considered
towards the band class with higher priority. The condition must be valid during the
period defined by attribute tReselectionCdma1xRtt. sNonServingCell is the RX-level
value of a neighboring cell.
0..63
N/A
63
New
threshXLow1xRtt
Cdma20001xRttBandRelation
Threshold used in reselection towards a low priority CDMA2000 1xRTT band class
expressed as an unsigned binary number equal to FLOOR ([-2 x 10 x log10 Ec/Io]) in
units of 0.5 db. If sServingCell < threshServingLow and sNeighbor > threshXLow (see
corresponding attribute), reselection towards this lower prioritized band class is
considered. The condition must be valid during the period defined by attribute
tReselectionCdma1xRtt. sServingCell is the RX level value of the serving cell and
sNeighborCell is the RX level value of a neighbor frequency.
0..63
N/A
63
New
userLabel
Cdma20001xRttBandRelation
0..128
N/A
N/A
""
New
cdma2000FreqRef
Cdma20001xRttFreqRelation
N/A
N/A
N/A
New
Cdma20001xRttFreqRelationId
Cdma20001xRttFreqRelation
N/A
N/A
N/A
New
csFallbackPrio
Cdma20001xRttFreqRelation
CDMA2000 1xRTT CSFB frequency priority This attribute prioritizes CDMA2000 1xRTT
frequencies among all frequencies related to the cell for UEs in connected mode.
Sets the priority to which frequency/frequency group to make CS Falback. The value
0 means the lowest priority. The value 7 means the highest priority.
0..7
N/A
New
csFallbackPrioEC
Cdma20001xRttFreqRelation
CDMA2000 1xRTT frequency priority for emergency calls This attribute prioritizes
CDMA2000 1xRTT frequencies for emergency calls among all frequencies/frequency
groups related to the cell for UEs in connected mode. Sets the priority to which
frequency to make emergency call CS Fallback. The value 0 means the lowest
priority. The value 7 means the highest priority.
0..7
N/A
New
userLabel
Cdma20001xRttFreqRelation
0..128
N/A
N/A
""
New
externalCdma20001xRttCellRef
Cdma20001xRttCellRelation
Reference to a ExternalCdma20001xRttCell
N/A
N/A
N/A
New
Cdma20001xRttCellRelationId
Cdma20001xRttCellRelation
N/A
N/A
N/A
New
includeInSystemInformation
Cdma20001xRttCellRelation
CDMA2000 cell inclusion in system information This attribute Indicates whether the
CDMA2000 cell is included in System Information. When the value is set to false,
the CDMA2000 cell is not included in SIB8. A maximum of 16 CDMA2000 cells can be
included per frequency. A maximum of 32 CDMA2000 cells can be included in SIB8.
N/A
N/A
N/A
true
New
includeInSystemInformationRel9
Cdma20001xRttCellRelation
N/A
N/A
N/A
false
New
userLabel
Cdma20001xRttCellRelation
0..128
N/A
N/A
""
New
ExternalCdma20001xRttCellId
ExternalCdma20001xRttCell
N/A
N/A
N/A
New
pnOffset
ExternalCdma20001xRttCell
N/A
N/A
N/A
New
reservedBy
ExternalCdma20001xRttCell
N/A
N/A
N/A
New
acBarring1xRttForMoDataPresent
ExternalCdma20001xRttCell
N/A
N/A
N/A
false
New
mscIdentifier
ExternalCdma20001xRttCell
MSC identity in CDMA 1xRTT network If this 1xRTT cell is referred by EUtranCell
this identifier will be used by eNodeB for tunnelling of CDMA200 1xRTT signaling
messages towards this MSC. It has to be configured for LTE CSFB to 1xRTT features
since it is used to fill a field in S1AP message sent to MME.
N/A
N/A
N/A
N/A
New
sid
ExternalCdma20001xRttCell
System unique identifier (15bits) This attribute is used along with the NID as a
pair to control when the UE should register or reregister with the CDMA2000 1xRTT
network. SID=0 is reserved. It is broadcast on SIB8. It is also used with CellId,
SectorNumber and NID for the 1xRTT cell global identity.
0..32768
N/A
N/A
N/A
New
nid
ExternalCdma20001xRttCell
Network unique identifier (16 bits) within a system used along with the sid as a
pair to control when the UE should register or reregister with the CDMA2000 1xRTT
network NID=0 and NID=65535 are reserved.
0..65535
N/A
N/A
N/A
New
cellIdentifier
ExternalCdma20001xRttCell
Cell identifier This attribute includes parameters that helps uniquely identify
1xRTT cells. If this 1xRTT cell is referred by EUtranCell marketId, switchNumber,
cellId, and sectorNumber must be used to set the IE CDMA2000 Sector ID in S1AP
message, Uplink S1 CDMA2000 tunneling. For the 1xRTT cell Global Identity, CellId,
SectorNumber, SID and NID are used. SID and NID will be sent on SIB8 for
preregistration to 1xRTT system.
N/A
N/A
N/A
N/A
New
acBarring1xRttMoData
ExternalCdma20001xRttCell
Access Barring parameters for CDMA2000 1xRTT capable UE originating signaling The
information is broadcast in SIB8. This is controlled by the licensing MO
CsfbTo1xRtt and acBarring1xRttForMoDataPresent
N/A
N/A
N/A
N/A
New
csfbRegParams1xRttMoData
ExternalCdma20001xRttCell
N/A
N/A
N/A
N/A
New
mobilityParams1xRttMoData
ExternalCdma20001xRttCell
N/A
N/A
N/A
N/A
New
userLabel
ExternalCdma20001xRttCell
0..128
N/A
N/A
""
New
externalCdma20001xRttCellRef
EUtranCellFDD
Reference to a ExternalCdma20001xRttCell
N/A
N/A
N/A
N/A
Removed
hrpdBandClass
Cdma2000FreqBand
N/A
N/A
N/A
New
cdmaBandClass
Cdma2000FreqBand
The CDMA frequency band in which the HRPD or 1xRTT carrier is located
N/A
N/A
N/A
New
minRandc
ENodeBFunction
Rand range datatype is the eight most significant bit (MSB) of the Rand used for
authentication The RandcRange attribute controls the minimum and maximum random
number values that can be generated. Typically a range of random numbers is
allocated to each system using this attribute.
1..254
N/A
N/A
New
maxRandc
ENodeBFunction
Rand range datatype is the eight most significant bit (MSB) of the Rand used for
authentication The RandcRange attribute controls the minimum and maximum random
number values that can be generated. Typically a range of random numbers is
allocated to each system using this attribute.
2..255
N/A
N/A
255
New
randUpdateInterval
ENodeBFunction
Random number update interval This attribute specifies the time interval in minutes
between random number generation. When this interval expires, the eNodeB generates
a new random number between MinRandc and MaxRandc.
15..1440
N/A
minutes
200
Table 18
Type of change
Enum name
Value
Literal
Description
New
CdmaMsIdType
EMSIS_ESN
The type of MS identity is IMSI_S and ESN. This value is applicable only when TMSI
is not supported
New
CdmaMsIdType
IMSI_or_TMSI
The type of MS identity is TMSI if the TMSI is supported and a TMSI is assigned to
the MS, or the type of MS identity will be IMSI
New
CdmaMsIdType
IMSI_ESN_or_TMSI
The type of MS identity is TMSI if the TMSI is supported and a TMSI is assigned to
the MS, or the type of MS identity is IMSI and ESN
Table 19
Type of change
Struct name
Description
Range
Unit
Default value
New
BandClassPrioCdma1xRtt
freqCdma
Carrier frequency within a CDMA2000 1xRTT band When the value is configured to
-1000, the parameter is ignored and the csFallbackPrio and csFallbackPrioEC apply
to all frequencies within one band.
-1000, 0..2047
N/A
-1000
New
BandClassPrioCdma1xRtt
cdma1xRttBandClass
N/A
N/A
BAND_CLASS_0
New
BandClassPrioCdma1xRtt
cellReselectionPriority
-1000, 0..7
N/A
-1000
New
BandClassPrioCdma1xRtt
csFallbackPrio
CDMA2000 1xRTT CSFB frequency priority This parameter prioritizes CDMA2000 1xRTT
frequencies among all frequencies related to the cell for UE in connected mode (0
means the lowest priority). When the value is configured to -1000, the parameter is
ignored. Sets the priority to which frequency to make CS Fallback to (0 means the
lowest priority). This parameter is only valid for normal CS Fallback calls. When
value is configured to -1000, the parameter is ignored.
-1000, 0..7
N/A
-1000
New
BandClassPrioCdma1xRtt
csFallbackPrioEC
CDMA2000 1xRTT CSFB frequency priority This parameter prioritizes CDMA2000 1xRTT
frequencies among all frequencies related to the cell for UE in connected mode. It
also sets the priority to which frequency to make CS Fallback to (0 means the
lowest priority). This parameter is only valid for emergency CS Fallback calls.
When value is configured to -1000, the parameter is ignored.
-1000, 0..7
N/A
-1000
New
AcBarringConfig1xRtt
acBarring0to9R9
Access class barring factor configuration This parameter used for calculating the
access class barring factor for access overload classes 0 through 9. It is the
parameter “PSIST” in C.S0004-A v6.0 for access overload classes 0 through 9.
0..63
N/A
New
AcBarringConfig1xRtt
acBarring10R9
Access class barring factor configuration This parameter used for calculating the
access class barring factor for access overload class N (N = 10 to 15). It is the
parameter “PSIST” in C.S0004-A v6.0 for access overload class 10.
0..7
N/A
New
AcBarringConfig1xRtt
acBarring11R9
Access class barring factor configuration This parameter used for calculating the
access class barring factor for access overload class N (N = 10 to 15). It is the
parameter “PSIST” in C.S0004-A v6.0 for access overload class 11.
0..7
N/A
New
AcBarringConfig1xRtt
acBarring12R9
Access class barring factor configuration This parameter used for calculating the
access class barring factor for access overload class N (N = 10 to 15). It is the
parameter “PSIST” in C.S0004-A v6.0 for access overload class 12.
0..7
N/A
New
AcBarringConfig1xRtt
acBarring13R9
Access class barring factor configuration Thisparameter used for calculating the
access class barring factor for access overload class N (N = 10 to 15). It is the
parameter “PSIST” in C.S0004-A v6.0 for access overload class 13.
0..7
N/A
New
AcBarringConfig1xRtt
acBarring14R9
Access class barring factor configuration This parameter used for calculating the
access class barring factor for access overload class N (N = 10 to 15). It is the
parameter “PSIST” in C.S0004-A v6.0 for access overload class 14.
0..7
N/A
New
AcBarringConfig1xRtt
acBarring15R9
Access class barring factor configuration This parameter used for calculating the
access class barring factor for access overload class N (N = 10 to 15). It is the
parameter “PSIST” in C.S0004-A v6.0 for access overload class 15.
0..7
N/A
New
AcBarringConfig1xRtt
acBarringMsgR9
Access class barring factor configuration This parameter used for modifying the
access class barring factor for message transmissions. It is the parameter
“MSG_PSIST” in C.S0004-A v6.0.
0..7
N/A
New
AcBarringConfig1xRtt
acBarringRegR9
Access class barring factor configuration This parameter used for modifying the
access class barring factor for autonomous registrations. It is the parameter
“REG_PSIST” in C.S0004-A v6.0
0..7
N/A
New
AcBarringConfig1xRtt
acBarringEmgR9
Access class barring factor configuration This parameter used for calculating the
access class barring factor for emergency calls and emergency message transmissions
for access overload classes 0 through 9. It is the parameter “PSIST_EMG” in
C.S0004-A v6.0
0..7
N/A
New
CsfbRegParams1xRtt
multipleSid
N/A
N/A
false
New
CsfbRegParams1xRtt
multipleNid
N/A
N/A
false
New
CsfbRegParams1xRtt
homeReg
N/A
N/A
true
New
CsfbRegParams1xRtt
foreignSidReg
N/A
N/A
true
New
CsfbRegParams1xRtt
foreignNidReg
N/A
true
New
CsfbRegParams1xRtt
parameterReg
N/A
N/A
true
New
CsfbRegParams1xRtt
powerUpReg
N/A
N/A
true
New
CsfbRegParams1xRtt
registrationPeriod
0, 29..85
80
New
CsfbRegParams1xRtt
registrationZone
CDMA2000 1xRTT Registration zone The range for zones is only 0-255. Unique zones
are identified by REG_ZONE, plus the SID/NID of the zone. When a mobile moves into
a new registration zone (uniquely identified by REG_ZONE + SID + NID with its own
timer) not on its internally stored list (up to TOTAL_ZONES entries) of visited
registration zones, zone registration causes the mobile to register. Zones in the
mobile are deleted upon expiration of a timer stored on mobile. After system
access, timers (ZONE_TIMER value) are enabled for every zone except the one where
the registration attempt was successful.
0..4095
N/A
New
CsfbRegParams1xRtt
totalZone
0..7
N/A
New
CsfbRegParams1xRtt
zoneTimer
CDMA2000 1xRTT zone timer length Range 0 – 7 (equates to 1, 2, 5, 10, 20, 30, 45,
60 minutes respectively). The higher the value, the less frequent the
registrations.
min
New
CsfbRegParams1xRtt
powerDownRegR9
CDMA2000 1xRTT Power-down registration indicator If set to TRUE, the UE that has a
valid / current CDMA2000 1xRTT pre-registration performs a CDMA2000 1xRTT power
down registration when it is switched off.
N/A
N/A
true
New
MobilityParams1xRtt
protocolRev
0..7
N/A
New
MobilityParams1xRtt
minProtocolRev
0..7
N/A
New
MobilityParams1xRtt
authenticationEnabled
N/A
N/A
false
New
MobilityParams1xRtt
maxNumAltServiceOption
MAX_NUM_ALT_SO in C.S0097 Use 0 for PREV 7 operation (to support 10-digit emergency
call numbers). Set the value to 1 Per CAB 128 only if not using PREV 7 BTS. Value 0
is also a flag to IVSN to query if mobile capability is not stored in VLR, even for
P_REV > 5 mobiles (Ensure a QueryOpt for IVSN is selected in MTX Table NOISBSC).
EnableORCM set TRUE will address CAB-128 concern and effectively negates reason for
CAB-128
0..7
N/A
New
MobilityParams1xRtt
preferredMsidType
N/A
N/A
IMSI_ESN_or_TMSI
New
MobilityParams1xRtt
mcc
Part of country code MCC of USA = 310 MCC of Canada = 302 MCC of Australia = 505
0..1023
N/A
New
MobilityParams1xRtt
imsiBit11and12
0..127
N/A
0
New
MobilityParams1xRtt
imsiTSupported
N/A
N/A
false
New
MobilityParams1xRtt
fchFchInitSetupRc3
8..255
0.125dB
56
New
MobilityParams1xRtt
fchFchInitSetupRc4
8..255
0.125dB
64
New
MobilityParams1xRtt
fchFchInitSetupRc5
0.125dB
56
New
MobilityParams1xRtt
fchFchInitSetupRc11
8..255
0.125dB
64
New
MobilityParams1xRtt
fchFchInitSetupRc12
8..255
0.125dB
64
New
MobilityParams1xRtt
pilotIncluded
PILOT_INC in C.S0097 This parameter indicates whether the pilot list is included.
N/A
N/A
false
New
MobilityParams1xRtt
localTimeOffset
LTM_OFF in C.S0097 This parameter indicates the offset of local time in units of
0.5hr from system time (GPS).
-24..23
0.5hr
New
MobilityParams1xRtt
dayLightSaving
N/A
N/A
false
New
MobilityParams1xRtt
gcsnaL2AckTimer
Length of time the mobile station or IWS waits after it sends GCSNA1xCircuitService
message, in units of 80ms
1..255
80ms
New
MobilityParams1xRtt
gcsnaSequenceContextTimer
1..255
100ms
New
SIB8
tReselectionCdma1xRtt
Cell reselection timer value applicable when evaluating cell reselection towards
CDMA2000 1xRTT The value corresponds to TreselectionCDMA_1xRTT in TS 36.304.
0..7
second
New
SIB8
tReselectionCdma1xRttSfHigh
25..100
100
New
SIB8
tReselectionCdma1xRttSfMedium
25..100
100
New
MSCid
marketId
0..65535
N/A
New
MSCid
switchNumber
0..255
N/A
New
Cdma1xRttCellId
cellId
Cell identity, 12 bit Refer to 3GPP2, A.S0014-C, table 4.2.17-4. It is used along
with sectorNumber, SID, and NID for the 1xRTT cell global identity. It is used with
marketId, switchNumber and sectorNumber to set the sectorId field on S1AP UL CDMA
Tunneling message.
1..4095
N/A
New
Cdma1xRttCellId
sectorNumber
Sector number, 4bit Refer to 3GPP2, A.S0014-C, table 4.2.17-4. It is used along
with CellId, SID, and NID for the 1xRTT cell global identity. It is used with
marketId, switchNumber and CellId to set the sectorId field on S1AP UL CDMA
Tunneling message.
0..15
N/A
Two new PM Events are introduced for the features CSFB CDMA2000 1xRX with blind RwR
and Enhanced CSFB CDMA2000 1xRTT:
◾RRC_CSFB_PARAMETERS_REQUEST_CDMA2000: Triggered at reception of the
CSFBParametersRequestCDMA2000 message by the eNodeB
◾RRC_CSFB_PARAMETERS_RESPONSE_CDMA2000: Triggered at transmission of the
CSFBParametersResponseCDMA2000 message by the eNodeB.
◾S1_DOWNLINK_S1_CDMA2000_TUNNELING: Triggered at reception of the DOWNLINK S1
CDMA2000 TUNNELING message by the eNodeB.
◾S1_UPLINK_S1_CDMA2000_TUNNELING: Triggered at transmission of the UPLINK S1
CDMA2000 TUNNELING message by the eNodeB.