Anda di halaman 1dari 80

ORDER NO.

CRT3555
DEH-2800MP/XN/EW

HIGH POWER CD/MP3/WMA PLAYER WITH RDS TUNER

DEH-2800MP /XN/EW
DEH-2800MPB/XN/EW
DEH-2820MP /XN/EW
HIGH POWER CD/MP3/WMA PLAYER WITH FM/MW/LW TUNER

DEH-281MP/XN/EW
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks

CX-3164 CRT3583 S10.5COMP1 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

For details, refer to "Important Check Points for Good Servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan


PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
K-ZZA. NOV. 2005 Printed in Japan
1 2 3 4

SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
A Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

- Safety Precautions for those who Service this Unit.


• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.

Caution:
B
1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.

- CD Section Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
C described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.

DEH-2800MP/XN/EW
2
1 2 3 4
5 6 7 8

[Important Check Points for Good Servicing]


In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.

3 Make sure the soldering of repaired locations is properly performed. B


When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C
7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.

0 Safe environment should be secured during servicing. D


When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts


Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws


To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DEH-2800MP/XN/EW
5 6 7 8
3
1 2 3 4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
A
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 8
2.1 PACKING ................................................................................................................................................... 8
2.2 EXTERIOR............................................................................................................................................... 10
2.3 CD MECHANISM MODULE..................................................................................................................... 12
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 14
3.1 BLOCK DIAGRAM ................................................................................................................................... 14
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)(DEH-2800MP/XN/EW, DEH-2800MPB/XN/EW, DEH-2820MP/
XN/EW) ................................................................................................................................................................... 16
3.3 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)(DEH-281MP/XN/EW) .......................................... 22
3.4 KEYBOARD UNIT.................................................................................................................................... 28
3.5 CD MECHANISM MODULE(GUIDE PAGE) ............................................................................................ 30
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 40
B 4.1 TUNER AMP UNIT................................................................................................................................... 40
4.2 KEYBOARD UNIT.................................................................................................................................... 44
4.3 CD CORE UNIT(S10.5COMP1)............................................................................................................... 46
5. ELECTRICAL PARTS LIST ............................................................................................................................ 48
6. ADJUSTMENT ............................................................................................................................................... 54
6.1 CD ADJUSTMENT................................................................................................................................... 54
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 56
6.3 ERROR MODE ........................................................................................................................................ 58
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM(DEH-281MP/XN/EW)................................................ 59
7. GENERAL INFORMATION ............................................................................................................................. 60
7.1 DIAGNOSIS ............................................................................................................................................. 60
7.1.1 DISASSEMBLY ..................................................................................................................................... 60
C 7.1.2 CONNECTOR FUNCTION DESCRIPTION .......................................................................................... 63
7.2 PARTS...................................................................................................................................................... 64
7.2.1 IC .......................................................................................................................................................... 64
7.2.2 DISPLAY ............................................................................................................................................... 73
7.3 OPERATIONAL FLOW CHART ............................................................................................................... 76
8. OPERATIONS ................................................................................................................................................ 77

DEH-2800MP/XN/EW
4
1 2 3 4
5 6 7 8

1. SPECIFICATIONS

DEH-2800MP/XN/EW
5 6 7 8
5
1 2 3 4

DEH-2800MP/XN/EW
6
1 2 3 4
5 6 7 8

DEH-2800MP/XN/EW
5 6 7 8
7
1 2 3 4

2. EXPLODED VIEWS AND PARTS LIST


NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
• Screw adjacent to mark on the product are used for disassembly.
"
• For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
2.1 PACKING

2
B 13
6

5 7

DEH-2800MP/XN/EW
8
1 2 3 4
5 6 7 8
(1)PACKING SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.

1 Cord Assy CDE7704


2 Accessory Assy CEA3865 11 Protector CHP2664
A
3 Fixing Screw(M2 x 4) CBA1994 12 Protector CHP2868
4 Screw CBA1650 13-1 Owner's Manual See Contrast table(2)
* 5 Polyethylene Bag CEG1160 13-2 Owner's Manual See Contrast table(2)
13-3 Installation Manual CRD4025
6 Handle CNC5395
7 Bush CNV3930 * 13-4 Passport CRY1013
8 Polyethylene Bag CEG-162 * 13-5 Warranty Card CRY1157
9 Carton See Contrast table(2) 14 Case Assy CXB3520
10 Contain Box See Contrast table(2)

(2) CONTRAST TABLE B


DEH-2800MP/XN/EW, DEH-2800MPB/XN/EW, DEH-2820MP/XN/EW and DEH-281MP/XN/EW are constructed
the same except for the following:
DEH-2800MP/XN/ DEH-2800MPB/XN/ DEH-2820MP/XN/
Mark No. Description DEH-281MP/XN/EW
EW EW EW
9 Carton CHG5632 CHG5627 CHG5628 CHG5681
10 Contain Box CHL5632 CHL5627 CHL5628 CHL5629
13-1 Owner's Manual CRD4023 CRD4023 CRD4023 CRD4026
13-2 Owner's Manual CRD4024 CRD4024 CRD4024 Not used
Owner's Manual,Installation Manual
Part No. Language C
CRD4023 English, Spanish, German

CRD4024 French, Italian, Dutch, Russian

CRD4026 English, Spanish, German, French, Italian, Dutch, Russian

CRD4025 English, Spanish, German, French, Italian, Dutch, Russian

DEH-2800MP/XN/EW
5 6 7 8
9
1 2 3 4

2.2 EXTERIOR

DEH-2800MP/XN/EW
10
1 2 3 4
5 6 7 8
(1)EXTERIOR SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.

1 Screw BSZ26P060FTC 31 Cover CNM6276


2 Screw BSZ26P100FTC 32 Panel CNS8403
A
3 Cord Assy CDE7704 33 Arm CNV4692
4 Cap CKX-003 34 Arm CNV4728
5 Cable CDE7985 35 Arm CNV5576

6 Case CNB2793 36 Screw IMS20P030FTB


7 Holder CNC8659 37 Detach Grille Assy See Contrast table(2)
8 Insulator CNM9145 38 Screw BPZ20P100FTB
9 Tuner Amp Unit See Contrast table(2) 39 Button(DETACH) CAC9382
10 Screw ASZ26P060FTC 40 Button(VOLUME(+ / -)) CAC9384

11 Screw BMZ26P160FTC 41 Button(TA,1-6,LOCAL/BSM,AUDIO) CAC9385 B


12 Screw BPZ26P080FTC 42 Button(↑,→,EJECT) CAC9386
> 13 Fuse(10 A) CEK1208 43 Button(↓,←) CAC9387
14 Pin Jack(CN352) CKB1059 44 Button(EQ,DISPLAY) CAC9388
15 Plug(CN901) CKM1376 45 Button(SOURCE,BAND) See Contrast table(2)

16 Connector(CN831) CKS3581 46 Spring CBH2210


17 Connector(CN651) CKS3834 47 Cover CNS8367
18 Connector(CN652) See Contrast table(2) 48 LCD See Contrast table(2)
19 Antenna Jack(CN401) CKX1056 49 Connector(CN1801) CKS3580
20 Holder CND2414 50 Holder CND2949
C
21 Holder See Contrast table(2) 51 Sheet See Contrast table(2)
22 Heat Sink CNR1762 52 Sheet See Contrast table(2)
23 FM/AM Tuner Unit See Contrast table(2) 53 Lighting Conductor CNV8712
24 Holder CND1054 54 Rubber CNV8713
25 Button(DETACH) CAC4836 55 Connector CNV8714

26 Spring CBH1835 56 Grille Unit See Contrast table(2)


27 Spring CBH2208 57 Chassis Unit See Contrast table(2)
28 Spring CBH2367 58 CD Mechanism Module(S10.5) CXK5752
29 Bracket CNC6791 59 Transistor(Q911,921,991) 2SD2396
60 IC(IC302) See Contrast table(2) D
30 Holder CNC8042

(2) CONTRAST TABLE


DEH-2800MP/XN/EW, DEH-2800MPB/XN/EW, DEH-2820MP/XN/EW and DEH-281MP/XN/EW are constructed
the same except for the following:
DEH-2800MP/XN/ DEH-2800MPB/XN/ DEH-2820MP/XN/
Mark No. Description DEH-281MP/XN/EW
EW EW EW
9 Tuner Amp Unit CWN1273 CWN1273 CWN1273 CWN1274
18 Connector(CN652) CKS4124 CKS4124 CKS4124 Not used
21 Holder CND2984 CND2984 CND2984 CND2413 E
23 FM/AM Tuner Unit CWE1951 CWE1951 CWE1951 CWE1954
37 Detach Grille Assy CXC5240 CXC5242 CXC5241 CXC5243

45 Button(SOURCE,BAND) CAC9516 CAC9516 CAC9516 CAC9383


48 LCD CAW1900 CAW1903 CAW1900 CAW1901
51 Sheet Not used CNM9766 Not used Not used
52 Sheet Not used CNM9767 Not used Not used
56 Grille Unit CXC5271 CXC5273 CXC5272 CXC5274

57 Chassis Unit CXC5265 CXC5267 CXC5266 CXC5268


60 IC(IC302) PAL007B PAL007B PAL007B TDA7386

DEH-2800MP/XN/EW
5 6 7 8
11
1 2 3 4

2.3 CD MECHANISM MODULE

DEH-2800MP/XN/EW
12
1 2 3 4
5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.

1 CD Core Unit(S10.5COMP1) CWX3176 50 Rack CNV8342


2 Connector(CN101) CKS4182 A
3 Connector(CN901) CKS5284 51 Roller CNV8343
4 Screw BMZ20P025FTC 52 Holder CNV8344
5 Screw BSZ20P040FTC 53 Arm CNV8345
54 Guide CNV8347
6 Screw(M2 x 3) CBA1511 55 Arm CNV8348
7 Screw(M2 x 4) CBA1835
8 Washer CBF1038 56 Arm CNV8349
9 ••••• 57 Arm CNV8350
10 Spring CBH2609 58 Clamper CNV8365
59 Arm CNV8386
11 Spring CBH2612 60 Guide CNV8396 B
12 Spring CBH2614
13 Spring CBH2616 61 Arm CNV8413
14 Spring CBH2617 62 Collar CNV8938
15 Spring CBH2620 63 Motor Unit(M2) CXC4026
64 Arm Unit CXC4027
16 Spring CBH2855 65 Chassis Unit CXC4028
17 Spring CBH2937
18 Spring CBH2735 66 Gear Unit CXC4029
19 Spring CBH2854 67 Frame Unit CXC4031
20 Spring CBH2642 68 Motor Unit(M1) CXC6742
69 Screw Unit CXC6359 C
21 Spring CBH2856 70 Screw JFZ20P020FTC
22 Spring CBH2857
23 Spring CBH2860 71 Screw JGZ17P022FTC
24 Spring CBH2861 72 Washer YE20FTC
25 Spring CBL1686 73 Pickup Unit(P10.5)(Service) CXX1942
74 Screw IMS26P030FTC
26 Arm CND1909
27 Frame CND2582
28 Bracket CND2583
29 Arm CND2584
D
30 Lever CND2585

31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201

36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211

41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV7218
45 Gear CNV7219

46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV7799
49 Arm CNV7805

DEH-2800MP/XN/EW
5 6 7 8
13
1 2 3 4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM


3.1 BLOCK DIAGRAM
A
A TUNER AMP UNIT
VDD
A,B,C

TUNPDO
TUNPCK
TUNPDI
7 6 13 5 10 9 8 11 14 18 19 20 21
FM/AM TUNER UNIT

NC

CE2

ROM_VDD

SL

DI
CK
CE1

LDET

DO

RDS_CK

RDS_DATA

RDS_LOCK

RDS_HSLK
IC 3 EEPROM IC 5

5.0V 5V 3.3V

OSC LPF
B CN401
ANTENNA 1
AM ANT FMRF
1 ATT
Rch
2 24
RDS_LO
IC 2
2.5V
FM ANT IC 1
3.3V RDS_HS
3 ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
RDS DECODER
RF adj
ANT adj RDS_CK

RDS_DA

T51 CF52 A,B,C

E
AUDIOGND

IC 4
OSCGND

TUN_Lch 1
VDD_3.3


RFGND

3.3V 3.3V 2.5V 2.5V


DGND

C
VCC
NC

CD_Lch 2
2 12 15 22 16 4 17

TUN 3.3V
VCC(SYS 8V)

PICKUP UNIT
(P10.5)(SERVICE) C
D CD CORE UNIT(S10.5COMP1)
CN101 V3R3D
LASER CN901 CN651
DIODE LD- 142
15 15 LOUT LOUT
D Q101
LD
IC201 LOUT
31 16 5
MD 143 UPD63763CGJ
5 5
REFO
PD SYSTEM
VREF 8 133
8 REFOUT RF-AMP,CD DECODER, 34 IC6
AC,BD MP3 , WMA, DECODER, XTAL PE551
HOLOGRAM
UNIT
F,E
DIGITAL SERVO / DATA PROCESSOR X201 PE551
16.93MHz
FOM
3 3
FOM /XTAL 35
FOP FOP LOCK/RFOK
FOCUS ACT. 2 2
MONITOR TOP 56
DIODE TRACKING ACT. 1 1 TOP
TOM TOM TD,FD SD,MD
4 4 XRST,XASTB,ADO,XCK,
LD+ XSO,XSI,WAIT,XINT
14 14
12
FOM
CD VDD
11
FOP
DRIVER Q701
14 VDD
TOP SWVDD 11 10 VDD
13
TOM
63
SPINDLE IC301
MOTOR M BA5835FP LOCK /CD3VON
43
16 14 /RESET RESET 36
SOP CLCONT 21 41 RESET 10 11 NC
15 CLCONT 39 CDMUTE
SOM CDMUTE 8 13
18 22 40
LCOP LOEJ LOEJ
LOAD/ CARRIAGE
MOTOR M 17
LCOM CONT
9 47 IC701 BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ
CONT PE5505A
BDATA,BSCK BDATA,BSCK
CD CONTROLLER Q991 CD VD
VD VD
E 32
X1 12
VD 1 20
Q992
B.UP
12EJ X701 2 19
31 4.00MHz
8EJ
30 X2 13
DSCSNS
42 49 VDCONT VDCONT
HOME VDCONT 9 12
S904 S905 S901
12EJ 8EJ HOME
CD3VON
46
S903
DSCSNS

1
V3R3D
4 IC203
NJM2886DL3-33 3
VD

+3.3V REGULATOR

A:DEH-2800MP/XN/EW
F
B:DEH-2800MPB/XN/EW
C:DEH-2820MP/XN/EW
D:DEH-281MP/XN/EW

DEH-2800MP/XN/EW
14
1 2 3 4
5 6 7 8

3 CN652
2
RESET 1
WIRED REMOTE
1 IC963 2
VDD
BD4834G A,B,C

60

RESET
47 CN352
KEYD
80
STRKEY1
TUNPDO 11
RLch 2
TUNPDI
LDET 61 LDET MUTE
TUNPDI 12 Q352
TUNPDO
SL 76 SL
TUNPCK 13 TUNPCK
VDD REGULATOR
CE1 56 Q911
TUNPCE1
CE2 55 TUNPCE2 VDD
Q912 B
SYSTEM CONTROLLER
IC601(1/2)
Q401 PE5517A:A,B,C 32
58
PE5518A:D DALMON
RDS_LOCK
RDSLK

RDS_HSLK 59
RDS57K BACKUP SENSE B.UP CN901
64 BSENS FUSE
BSENS 1 1
Q402 10A BACK UP
62 Q931
RDS_CK 63 ASENS ACC
RCK ASENS 3 3
ACC
RDS_DATA 57
RDT ACC SENSE

2 2
A,B,C GND

B.UP
POWER AMP 6,20
ELECTRONIC VOLUME/
SOURCE SELECTOR VCC
TUN_Lch 1 6 14 23
IN1-L Front_ L FLIn FL-
FL- 10 10

IC151 FL+
21
12 12
FL+ C
CD_Lch 2 7 12 3 RL-
IN2-L PML014A Rear_ L RLIn RL- 9 9
IC302 RL+
PAL007B(50W):A,B,C RL+ 5
11 11
TDA7386(45W):D A,B,C
22 25 BREM
MUTE STBY BREM 6 6
B.REM
4
VCK, VDT, VST

MUTE VCC
Q452(2/2) (SYS 8V)

TUN 3V REG. SYS 8V REG.


Q921
1 IC901 3
MUTE TUN3V
NJM2885DL1-33
B.UP
Q452(1/2) Q923
48
MUTE

43 SYSPW RR RR
SYSPW - +
BACK FR FR
UP - + D
B. FL FL
SYSTEM CONTROLLER REM +
-
IC601(2/2) GND ACC RL RL
PE5517A:A,B,C B.REMOTE - +
PE5518A:D 49 6 IC551 1
ANTPW
TPD1018F
D

70
X1
X601
69 12.58291MHz
X2
36
NC B KEYBOARD UNIT
SWVDD CN831 CN1801
Q801
SWVDD SW5V KEY MATRIX
VDD 5 5 5.1V
S1803

SWVDD
21 SWVDD S1801
VOL+
S1802
5ch/RPT
S1825
BTB
S1804
3ch
S1806
2ch
E
S1805
66 SOURCE SOURCE S1809
SRC 6 6 S1807 S1808 S1810 S1811
S1839
SOURCE VOL- 1ch CLOCK LOC 6ch/PAUSE
65 DSENS DSENS
DSENS 8 8
S1813 S1814 S1815 S1816
ILMPW S1812 S1821 S1822 S1823 S1824
Q821 4ch/RDM LEFT DOWN UP RIGHT
ILM ILL
B.UP 7 7
S1818 S1819 S1826
S1838 S1829 S1820 S1827
Q822
AUDIO EJECT BAND DISP/LOUD
22
ILMPW

KEY DATA 22
X0
X1801
9 DPDT DPDT 18 23 5MHz
DPDT 4 4 DPDT X1
8
LCD DRIVER/ F
KYDT
KYDT
3 3
KYDT 20
KYDT KEY CONTROLLER
IC1801
PD6340A LCD

DEH-2800MP/XN/EW
5 6 7 8
15
1 2 3 4

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)(DEH-2800MP/XN/EW,


DEH-2800MPB/XN/EW, DEH-2820MP/XN/EW)
A Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".

Large size
SCH diagram
A-a
A-a A-b

A-a A-b Guide page

C CN901

A-a A-b Detailed page

C
FM/AM TUNER UNIT

SOURCE
PE5518A

D
STR

CDRESET

B CN1801

NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor.
2.2 ← 2R2
No differentiation is made between chip capacitors and
0.022 ← R022
discrete capacitors.

The > mark found on some component parts indicates


F the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.

A
DEH-2800MP/XN/EW
16
1 2 3 4
5 6 7 8

A-b
A TUNER AMP UNIT

>

TDA7386 45W
SOURCE

CEK1208 10A

> BACKUP

600µH GND

ACC

B.REM

D
RL—

FL—
STRKEY2
RL+

FL+
RR—

FR—
RR+

FR+
CDRESET

RR RR
- +
BACK FR FR
UP - +
B. FL FL
REM - +
RL RL
GND ACC
- + E

A
DEH-2800MP/XN/EW
5 6 7 8
17
1 2 3 4

A-b 1 2 3

CN901

SOURCE

B
C

C
A-a A-b

FM/AM TUNER UNIT


F

A-a
DEH-2800MP/XN/EW
18
1 2 3 4
FM/AM T
STRKEY2
5

5
CDRESET

6
6

B CN1801
4

DEH-2800MP/XN/EW
7
7

NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor.
2.2 ← 2R2
No differentiation is made between chip capacitors and
0.022 ← R022
discrete capacitors.

The > mark found on some component parts indicates


the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
8

8
A-a A-b

A-a
A-b

19
E
A

D
C

F
B
F
E
B
A

D
C

20
A-a A-b

A-b
A TUNER AMP UNIT

1
1

2
2

2
>

DEH-2800MP/XN/EW
3

3
3

4
4

CEK1208 10A

> BACKUP

600µH GND

ACC

B.REM
CEK1208 10A

> BACKUP

600µH GND

ACC

B.REM

RL—

FL—
RL+
5

5
FL+
RR—

FR—
RR+

FR+

RR RR
- +

6
6

BACK FR FR
UP - +
B. FL FL
REM - +
GND ACC RL RL
- +

DEH-2800MP/XN/EW
7
7
8

8
A-a A-b

A-b
21
E
A

D
C

F
B
1 2 3 4

3.3 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)(DEH-281MP/XN/EW)


Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
A
Large size
SCH diagram
A-a
A-a A-b

A-a A-b Guide page

C CN901
A-a A-b Detailed page

C
FM/AM TUNER UNIT

SOURCE
PE5518A

CDRESET

B CN1801

NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor.
2.2 ← 2R2
No differentiation is made between chip capacitors and
0.022 ← R022
discrete capacitors.

The > mark found on some component parts indicates


the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
F identical designation.

A
DEH-2800MP/XN/EW
22
1 2 3 4
5 6 7 8

A
A-b
A TUNER AMP UNIT

901

>

TDA7386 45W
C
SOURCE

CEK1208 10A

> BACKUP

600µH GND

ACC

B.REM

RL—

FL—
STRKEY2
RL+ D
FL+
RR—

FR—
RR+

FR+
CDRESET

RR RR
- +
BACK FR FR
UP - +
B. FL FL
REM - +
GND ACC RL RL
- +

A
DEH-2800MP/XN/EW
5 6 7 8
23
1 2 3 4

A-b 1 2 3

CN901

SOURCE

PE5518A
C

C
A-a A-b

FM/AM TUNER UNIT


F

A-a
DEH-2800MP/XN/EW
24
1 2 3 4
FM/AM T
PE5518A

STRKEY2
5

5
CDRESET

6
6

B CN1801
4

DEH-2800MP/XN/EW
7
7

NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor.
2.2 ← 2R2
No differentiation is made between chip capacitors and
0.022 ← R022
discrete capacitors.

The > mark found on some component parts indicates


the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
8

8
A-a A-b

A-a
A-b

25
E
A

D
C

F
B
F
E
B
A

D
C

26
A-a A-b

A-b
A TUNER AMP UNIT

1
1

2
2

2
>

DEH-2800MP/XN/EW
3

3
3

TDA7386 45W

4
4

CEK1208 10A

> BACKUP

600µH GND

ACC

B.REM
CEK1208 10A

> BACKUP

600µH GND

ACC

B.REM

RL—

FL—
RL+
5

5
FL+
RR—

FR—
RR+

FR+

RR RR
- +

6
6

BACK FR FR
UP - +
B. FL FL
REM - +
GND ACC RL RL
- +

DEH-2800MP/XN/EW
7
7
8

8
A-a A-b

A-b
27
E
A

D
C

F
B
1 2 3 4

3.4 KEYBOARD UNIT

B KEYBOARD UNIT

LCD DRIVER

B
DEH-2800MP/XN/EW
28
1 2 3 4
5 6 7 8

TA

A CN831

SML-310VT(DEH-2800MP/XN/EW, DEH-2800MPB/XN/EW, DEH-281MP/XN/EW)


D

D1803-1809, D1812-1821,D1823-1825 :
SML-310PT(DEH-2820MP/XN/EW)

LCD :
CAW1900(DEH-2800MP/XN/EW, DEH-2820MP/XN/EW)
CAW1903(DEH-2800MPB/XN/EW)
CAW1901(DEH-281MP/XN/EW)

B
DEH-2800MP/XN/EW
5 6 7 8
29
1 2 3 4

3.5 CD MECHANISM MODULE(GUIDE PAGE)

A
C-a

C
S

F
C
S

F
B
PICKUP UNIT(P10.5)(SERVICE)
$

F
F
T
T

T
F
@
T
F !
F
C T

SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.

NC
NC
NC
NC
NC
M1 CXC6742 CD DRIVER NC
NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC
C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6
NC
F C NC

7
9

4
E NC
NC
F
F
3 T
T

2
C
C
S
S

C
DEH-2800MP/XN/EW
30
1 2 3 4
5 6 7 8

A
C-b

B
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE

C CD CORE UNIT(S10.5COMP1)
0

+ 3.3 V REGULATOR
C

D
NC
NC
NC
NC
NC

NC
NC
NC
NC
NC

NC
NC

NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC
NC
NC
NC
NC
NC
NC SRAMLEVEL1
SRAMLEVEL0
5

(S904)
CD CONTROLLER
NC
(S905)
E
NC
NC

A CN651

C
DEH-2800MP/XN/EW
5 6 7 8
31
F
E
B
A

D
C

32
C-a
A-a C-b

C-a
C-b

1
1

T
F

S
C
1

T
F

S
C

2
2

PICKUP UNIT(P10.5)(SERVICE)
$

DEH-2800MP/XN/EW
F
F
T
T

3
3

T
F
@
T
F !
F
T

4
4

SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF

The underlined indicates the switch position.


SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
5

5
2
NC
NC
NC
NC

NC
M1 CXC6742 CD DRIVER NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC

6
6

C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6
NC
F C NC

7
9

4
NC
NC
F
F
3 T

DEH-2800MP/XN/EW
T

7
7

S
S
C
C

1
3
8

8
C-a
A-a C-b

C-a
C-b

33
E
A

D
C

F
B
F
E
B
A

D
C

34
C-a C-b

C-b
1
1

2
2

SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE

C CD CORE UNIT(S10.5COMP1)

DEH-2800MP/XN/EW
0

3
3

+ 3.3 V REGULATOR

4
4
5

5
2
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC

6
6

NC
NC
NC
NC
NC
NC SRAMLEVEL1
SRAMLEVEL0
5

(S904)
CD CONTROLLER (S905)
NC
NC

DEH-2800MP/XN/EW
NC

7
7

A CN651

3
8

8
C-a C-b

C-b
35
E
A

D
C

F
B
1 2 3 4

- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div
2 8SNS 5 V/div 4 CLCONT 5 V/div 2 8SNS 5 V/div
3 12SNS 5 V/div 5 VD 10 V/div 3 12SNS 5 V/div

12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation

Ref.: Ref.: Ref.:


GND GND GND

Mode: Mode: Mode:


B Normal Normal Normal

6 SIN 1 V/div 1 s/div 6 SIN 1 V/div 1 s/div 6 SIN 1 V/div 1 s/div


7 CIN 500 mV/div 7 CIN 500 mV/div 7 CIN 500 mV/div
8 TIN 500 mV/div 8 TIN 500 mV/div 8 TIN 500 mV/div

12 cm CD-DA setup operation after loading 12 cm CD-ROM(1 session) setup operation 12 cm CD-ROM(3 sessions) setup operation
after loading after loading

C Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


Normal Normal Normal

9 FIN 200 mV/div 500 ms/div ! TE 500 mV/div 200 ms/div @ FE 500 mV/div 20 ms/div
0 RFOK 2 V/div @ FE 500 mV/div 9 FIN 500 mV/div
6 SIN 2 V/div ! TE 500 mV/div
8 TIN 500 mV/div
12 cm CD-DA Source On setup operation Source On setup operation CD-DA Play operation
D

Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


Normal Normal Normal

@ FE 500 mV/div 20 ms/div # MDX 2 V/div 50 ms/div # MDX 2 V/div 5 µs/div


9 FIN 500 mV/div 6 SIN 200 mV/div 6 SIN 500 mV/div
E
! TE 500 mV/div
8 TIN 500 mV/div
CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


Normal Normal Normal

DEH-2800MP/XN/EW
36
1 2 3 4
5 6 7 8

9 FIN 500 mV/div 200 ms/div ! TE 500 mV/div 2 ms/div $ RFAGC 1 V/div 500 µs/div
@ FE 500 mV/div $ RFAGC 500 mV/div ! TE 500 mV/div A
8 TIN 500 mV/div

Focus Search waveform Track Open waveform 1 Track Jump waveform

Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


TEST TEST TEST

$ RFAGC 1 V/div 500 µs/div $ RFAGC 1 V/div 1 ms/div $ RFAGC 1 V/div 2 ms/div
! TE 500 mV/div ! TE 500 mV/div ! TE 500 mV/div
8 TIN 500 mV/div 8 TIN 500 mV/div 8 TIN 500 mV/div

4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform

Ref.: Ref.: Ref.:


REFO REFO REFO
C
Mode: Mode: Mode:
TEST TEST TEST

$ RFAGC 1 V/div 200 ms/div % LOUT 1 V/div 200 µs/div 1 DSCSNS 5 V/div 500 ms/div
! TE 1 V/div ^ ROUT 1 V/div 2 8SNS 5 V/div
7 CIN 500 mV/div 3 12SNS 5 V/div
6 SIN 2 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation

D
Ref.: Ref.: Ref.:
REFO AGND GND

Mode: Mode: Mode:


Normal Normal Normal

1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 6 SIN 1 V/div 500 ms/div
5 CLCONT 5 V/div 2 8SNS 5 V/div 7 CIN 500 mV/div
4 LOEJ 5 V/div 3 12SNS 5 V/div 8 TIN 500 mV/div
E
12 cm CD Eject operation 8 cm CD Eject operation CD-DA → CD-ROM mode change(Band key)

Ref.: Ref.: Ref.:


GND GND REFO

Mode: Mode: Mode:


Normal Normal Normal

DEH-2800MP/XN/EW
5 6 7 8
37
1 2 3 4

6 SIN 1 V/div 500 ms/div $ RFAGC 1 V/div 500 µs/div


A 7 CIN 500 mV/div 8 TIN 1 V/div
8 TIN 500 mV/div ! TE 1 V/div
9 FIN 1 V/div
CD-ROM → CD-DA mode change(Band key) Black dot(800 µm) during play

Ref.: Ref.:
REFO REFO

Mode: Mode:
Normal Normal

DEH-2800MP/XN/EW
38
1 2 3 4
5 6 7 8

DEH-2800MP/XN/EW
5 6 7 8
39
1 2 3 4

4. PCB CONNECTION DIAGRAM


4.1 TUNER AMP UNIT
A
A TUNER AMP UNIT
NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB WIRED REMOTE CONTROL ADAPTORS
include all necessary parts for
several destination.
For further information for

1
respective destinations, be sure CORD ASSY
to check with the schematic dia-

2
gram.
2.Viewpoint of PCB diagrams

3
Connector Capacitor

B SIDE A

SIDE B
P.C.Board Chip Part

CN651
E

C CN901

F B CN1801

A
DEH-2800MP/XN/EW
40
1 2 3 4
5 6 7 8

A
SIDE A

REAR OUTPUT ANTENNA JACK

1 2 3 4 B

FM/AM TUNER UNIT


D

FRONT A
DEH-2800MP/XN/EW
5 6 7 8
41
1 2 3 4

A
A TUNER AMP UNIT

IC151

E
PCL TEST

A
DEH-2800MP/XN/EW
42
1 2 3 4
5 6 7 8

A
SIDE B

IC963

E
TEST

A
DEH-2800MP/XN/EW
5 6 7 8
43
1 2 3 4

4.2 KEYBOARD UNIT

B KEYBOARD UNIT SIDE A


B KEYBOARD UNIT SIDE B
A SOURCE

BAND
EJECT

RIGHT

DOWN
UP

AUDIO
R1815
LEFT

R1814

R1813

R1812
LOC
6ch/PAUSE

C
5ch/RPT
4ch/RDM

D
3ch

A CN831
2ch
1ch

D1810

E R1808 R1809
DISP

TA

R1807
EQ

R1811
VOL+

VOL-

B
DEH-2800MP/XN/EW
44
1 2 3 4
5 6 7 8

DEH-2800MP/XN/EW
5 6 7 8
45
1 2 3 4

4.3 CD CORE UNIT(S10.5COMP1)

C CD CORE UNIT(S10.5COMP1) SIDE A


A
PICKUP UNIT(P10.5)(SERVICE)

A
CN651

REFO1

E
20

HOME

CN901
D

M2
LOADING
/CARRIAGE
MOTOR

M1
E
SPINDLE
MOTOR

IC203 IC301

C
DEH-2800MP/XN/EW
46
1 2 3 4
5 6 7 8

C CD CORE UNIT(S10.5COMP1) SIDE B


A

8EJ
12EJ
B

DSCSNS

C
DEH-2800MP/XN/EW
5 6 7 8
47
1 2 3 4

5. ELECTRICAL PARTS LIST


NOTE:
A • Parts whose parts numbers are omitted are subject to being not supplied.
• The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
• The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 401 (B,151,43) Transistor UMH1N
Unit Number : CWN1273(DEH-2800MP/ Q 402 (B,151,54) Transistor UMH1N
XN/EW, DEH-2800MPB/XN/EW, DEH- Q 452 (B,139,128) Transistor UMD2N
Q 801 (B,80,29) Transistor 2SA1036K
2820MP/XN/EW)
Q 821 (B,43,15) Transistor 2SA1036K
C
Unit Name : Tuner Amp Unit Q 822 (B,31,17) Transistor DTC114EU
Q 911 (A,8,116) Transistor 2SD2396
Unit Number : CWN1274(DEH-281MP/XN/ Q 912 (B,9,128) Transistor UMD2N
Q 921 (A,8,103) Transistor 2SD2396
EW)
Unit Name : Tuner Amp Unit Q 923 (B,24,79) Transistor UMD2N
Q 931 (B,61,107) Transistor UMX1N
Unit Number : (DEH-2800MP/XN/EW, Q 991 (A,8,69) Transistor 2SD2396
Q 992 (B,21,58) Transistor UMD2N
DEH-2800MPB/XN/EW, DEH-281MP/XN/ D 551 (A,62,124) Diode MPG06G-6415G3

EW) D 552 (A,59,124) Diode MPG06G-6415G3


D 901 (A,35,131) Diode MPG06G-6415G3
Unit Name : Keyboard Unit D 902 (A,35,128) Diode MPG06G-6415G3
D
Unit Number : (DEH-2820MP/XN/EW) D 911 (A,21,106) Diode MPG06G-6415G3
D 912 (A,18,120) Diode HZS6L(B2)
Unit Name : Keyboard Unit
D 921 (A,24,87) Diode HZS9L(B3)
Unit Number : CWX3176 D 931 (A,69,115) Diode HZS7L(C3)
D 932 (A,54,108) Diode HZS7L(A1)
Unit Name : CD Core D 961 (A,56,74) Diode 1SS133
D 991 (A,20,66) Diode HZS7L(C3)
Unit(S10.5COMP1)
L 151 (A,146,93) Inductor LAU2R2K
L 401 (A,157,58) Inductor LAU2R2K

E A
Unit Number : CWN1273(DEH-2800MP/
L
L
L
402
404
601
(A,148,88) Inductor
(B,160,101) Inductor
(A,93,85) Ferri-Inductor
LAU2R2K
LCTAW220J2520
LAU100K

XN/EW, DEH-2800MPB/XN/EW, DEH- L 602 (A,103,67) Inductor LAU2R2K


L 651 (A,41,38) Ferri-Inductor LAU100K
2820MP/XN/EW) L 801 (A,88,25) Inductor LAU2R2K
Unit Name : Tuner Amp Unit L 901 (A,36,108) Choke Coil 600µH CTH1280
X 601 (A,103,71) Radiator 12.58291MHz CSS1402
MISCELLANEOUS >FU352 (B,143,135) Fuse 3A CEK1286
> Fuse 10A CEK1208
IC 151 (B,133,80) IC PML014A
AR401 (A,161,110) Arrester DSP-201M-S00B
IC 302 (A,94,135) IC PAL007B
FM/AM Tuner Unit CWE1951
F IC 601 (B,87,62) IC PE5517A
IC 901 (B,143,29) IC NJM2885DL1-33
IC 963 (B,62,83) IC BD4834G
RESISTORS

Q 352 (B,160,129) Transistor UMH3N R 301 (B,93,104) RS1/16S153J

DEH-2800MP/XN/EW
48
1 2 3 4
5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 353 (B,144,128) RS1/16S821J R 934 (B,61,110) RS1/16S473J
R 354 (B,164,128) RS1/16S821J R 935 (B,55,106) RS1/16S473J
R 357 (B,145,133) RS1/16S223J R 936 (B,57,110) RS1/16S223J
R 358 (B,164,135) RS1/16S223J R 940 (B,86,81) RS1/16S104J A

R 401 (B,144,52) RAB4C223J R 941 (B,89,81) RS1/16S104J


R 405 (B,155,62) RS1/16S681J R 961 (B,67,78) RS1/16S102J
R 406 (B,160,81) RS1/16S681J R 962 (B,62,78) RS1/16S183J
R 407 (B,159,87) RAB4C681J R 991 (A,20,61) RD1/4PU271J
R 408 (A,153,49) RD1/4PU331J R 992 (A,15,68) RD1/4PU221J

R 409 (B,123,44) RS1/16S331J CAPACITORS


R 414 (B,159,91) RS1/16S681J
R 420 (B,99,48) RS1/16S681J C 151 (B,160,73) CKSRYB224K10
R 454 (B,135,127) RS1/16S103J C 152 (B,160,75) CKSRYB224K10
R 455 (B,140,130) RS1/16S153J C 153 (B,130,69) CKSRYB105K6R3
B
C 154 (B,142,74) CKSRYB105K6R3
R 456 (B,140,133) RS1/16S221J C 165 (B,136,91) CKSRYB104K16
R 457 (B,99,50) RS1/16S681J
R 602 (B,109,58) RS1/16S473J C 166 (A,134,92) CEJQ470M10
R 606 (B,111,61) RS1/16S104J C 167 (A,128,92) CEJQ100M16
R 607 (B,107,61) RS1/16S222J C 301 (B,119,108) CKSQYB474K16
C 302 (B,128,111) CKSQYB474K16
R 608 (B,106,74) RS1/16S0R0J C 303 (B,131,122) CKSQYB474K16
R 609 (B,102,43) RS1/16S473J
R 610 (B,99,52) RS1/16S681J C 304 (B,123,107) CKSQYB474K16
R 612 (B,106,57) RS1/16S103J C 305 (B,119,113) CKSRYB474K10
R 613 (B,72,54) RS1/16S104J C 306 (B,131,114) CKSRYB474K10
C 307 (B,134,124) CKSRYB474K10
R 633 (B,53,73) RS1/16S104J C
C 308 (B,126,109) CKSRYB474K10
R 650 (B,50,50) RS1/16S102J
R 651 (B,58,36) RS1/16S104J C 309 (B,136,132) CKSQYB225K10
R 652 (B,60,38) RS1/16S102J C 310 (B,137,136) CKSQYB225K10
R 655 (A,76,51) RD1/4PU102J C 312 (A,104,125) CEJQ100M16
C 313 (B,100,142) CKSRYB104K16
R 659 (B,84,43) RS1/16S221J C 353 (A,134,120) CEJQ2R2M50
R 660 (B,93,46) RS1/16S681J
R 662 (B,102,40) RS1/16S682J C 354 (A,134,110) CEJQ2R2M50
R 663 (B,81,43) RS1/16S682J C 401 (B,160,69) CKSRYB103K50
R 670 (B,76,54) RS1/16S104J C 403 (A,151,58) CEJQ470M6R3
C 404 (A,151,95) CEJQ101M10
R 671 (B,79,43) RS1/16S104J C 405 (B,167,97) CKSRYB103K50
R 674 (B,18,143) RS1/16S102J D
R 675 (B,18,145) RS1/16S102J C 407 (B,159,60) CKSQYB475K6R3
R 801 (B,77,29) RS1/16S153J C 409 (B,147,56) CCSRCH470J50
R 802 (B,95,25) RS1/16S153J C 420 (B,108,43) CCSRCH470J50
C 451 (A,132,132) CEJQ330M10
R 803 (B,104,23) RS1/16S222J C 601 (B,69,83) CKSRYB103K50
R 821 (B,34,18) RS1/16S562J
R 822 (B,74,29) RS1/16S102J C 604 (B,98,75) CCSRCH200J50
R 823 (B,38,15) RS1/16S103J C 605 (B,102,75) CCSRCH200J50
R 833 (A,80,17) RD1/4PU222J C 608 (B,91,48) CCSRCH101J50
C 610 (A,101,82) CEJQ4R7M35
R 834 (A,82,17) RD1/4PU222J C 612 (B,89,75) CCSRCH470J50
R 835 (A,68,20) RD1/4PU102J
E
R 836 (A,72,26) RD1/4PU104J C 613 (B,100,78) CKSRYB105K6R3
R 837 (A,78,25) RD1/4PU103J C 651 (B,42,40) CKSRYB105K10
R 838 (B,89,89) RS1/16S102J C 670 (B,44,42) CCSRCH221J50
C 801 (B,104,25) CKSRYB105K6R3
R 841 (B,52,15) RS1/16S1R0J C 832 (B,49,13) CKSRYB104K16
R 848 (A,105,46) RD1/4PU102J
R 851 (A,103,46) RD1/4PU102J C 901 (A,36,140) CEAT332M16(P45)
R 852 (B,91,89) RS1/16S102J C 911 (A,16,96) CEJQ470M10
R 911 (B,11,124) RS1/16S183J C 912 (B,12,133) CKSRYB103K50
C 913 (A,19,137) CEAT331M16
R 912 (A,8,131) RD1/4PU152J C 921 (A,25,66) 330µF/16V CCH1326
R 913 (B,18,110) RS1/16S0R0J
R 923 (A,19,90) RD1/4PU821J C 922 (A,24,82) CEJQ101M16 F
R 931 (B,65,112) RS1/16S473J C 923 (B,23,85) CKSRYB103K50
R 932 (B,65,110) RS1/16S104J C 961 (B,56,85) CKSRYB473K50
C 962 (B,60,75) CKSRYB105K6R3
R 933 (A,55,116) RD1/4PU102J
DEH-2800MP/XN/EW
5 6 7 8
49
1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 981 (B,135,25) CKSRYB334K10 R 354 (B,164,128) RS1/16S821J
R 357 (B,145,133) RS1/16S223J
C 983 (A,144,38) CEJQ470M10 R 358 (B,164,135) RS1/16S223J
A C 991 (B,17,63) CKSRYB473K50
C 992 (A,17,54) CEJQ101M10 R 405 (B,155,62) RS1/16S681J
R 407 (B,159,87) RAB4C681J

A
Unit Number : CWN1274(DEH-281MP/XN/
R
R
R
414
420
421
(B,159,91)
(B,99,48)
(B,160,79)
RS1/16S681J
RS1/16S681J
RS1/16S473J

EW) R 454 (B,135,127) RS1/16S103J


Unit Name : Tuner Amp Unit R 455 (B,140,130) RS1/16S153J
R 456 (B,140,133) RS1/16S221J
R 457 (B,99,50) RS1/16S681J
MISCELLANEOUS R 601 (B,100,58) RS1/16S103J

B IC 151 (B,133,80) IC PML014A R 602 (B,109,58) RS1/16S473J


IC 302 (A,94,135) IC TDA7386 R 606 (B,111,61) RS1/16S104J
IC 551 (B,61,118) IC TPD1018F R 607 (B,107,61) RS1/16S222J
IC 601 (B,87,62) IC PE5518A R 608 (B,106,74) RS1/16S0R0J
IC 901 (B,143,29) IC NJM2885DL1-33 R 609 (B,102,43) RS1/16S473J

IC 963 (B,62,83) IC BD4834G R 610 (B,99,52) RS1/16S681J


Q 352 (B,160,129) Transistor UMH3N R 612 (B,106,57) RS1/16S103J
Q 452 (B,139,128) Transistor UMD2N R 613 (B,72,54) RS1/16S104J
Q 801 (B,80,29) Transistor 2SA1036K R 633 (B,53,73) RS1/16S104J
Q 821 (B,43,15) Transistor 2SA1036K R 650 (B,50,50) RS1/16S102J

Q 822 (B,31,17) Transistor DTC114EU R 651 (B,58,36) RS1/16S104J


C Q 911 (A,8,116) Transistor 2SD2396 R 652 (B,60,38) RS1/16S102J
Q 912 (B,9,128) Transistor UMD2N R 655 (A,76,51) RD1/4PU102J
Q 921 (A,8,103) Transistor 2SD2396 R 659 (B,84,43) RS1/16S221J
Q 923 (B,24,79) Transistor UMD2N R 660 (B,93,46) RS1/16S681J

Q 931 (B,61,107) Transistor UMX1N R 662 (B,102,40) RS1/16S682J


Q 991 (A,8,69) Transistor 2SD2396 R 663 (B,81,43) RS1/16S682J
Q 992 (B,21,58) Transistor UMD2N R 670 (B,76,54) RS1/16S104J
D 551 (A,62,124) Diode MPG06G-6415G3 R 671 (B,79,43) RS1/16S104J
D 552 (A,59,124) Diode MPG06G-6415G3 R 801 (B,77,29) RS1/16S153J

D 901 (A,35,131) Diode MPG06G-6415G3 R 802 (B,95,25) RS1/16S153J


D 902 (A,35,128) Diode MPG06G-6415G3 R 803 (B,104,23) RS1/16S222J
D D 911 (A,21,106) Diode MPG06G-6415G3 R 821 (B,34,18) RS1/16S562J
D 912 (A,18,120) Diode HZS6L(B2) R 822 (B,74,29) RS1/16S102J
D 921 (A,24,87) Diode HZS9L(B3) R 823 (B,38,15) RS1/16S103J

D 931 (A,69,115) Diode HZS7L(C3) R 833 (A,80,17) RD1/4PU222J


D 932 (A,54,108) Diode HZS7L(A1) R 834 (A,82,17) RD1/4PU222J
D 961 (A,56,74) Diode 1SS133 R 835 (A,68,20) RD1/4PU102J
D 991 (A,20,66) Diode HZS7L(C3) R 836 (A,72,26) RD1/4PU104J
L 151 (A,146,93) Inductor LAU2R2K R 837 (A,78,25) RD1/4PU103J

L 401 (A,157,58) Inductor LAU2R2K R 838 (B,89,89) RS1/16S102J


L 402 (A,148,88) Inductor LAU2R2K R 841 (B,52,15) RS1/16S1R0J
L 404 (B,160,101) Inductor LCTAW220J2520 R 848 (A,105,46) RD1/4PU102J
E L 601 (A,93,85) Ferri-Inductor LAU100K R 851 (A,103,46) RD1/4PU102J
L 602 (A,103,67) Inductor LAU2R2K R 852 (B,91,89) RS1/16S102J

L 651 (A,41,38) Ferri-Inductor LAU100K R 911 (B,11,124) RS1/16S183J


L 801 (A,88,25) Inductor LAU2R2K R 912 (A,8,131) RD1/4PU152J
L 901 (A,36,108) Choke Coil 600µH CTH1280 R 913 (B,18,110) RS1/16S0R0J
X 601 (A,103,71) Radiator 12.58291MHz CSS1402 R 923 (A,19,90) RD1/4PU821J
>FU352 (B,143,135) Fuse 3A CEK1286 R 931 (B,65,112) RS1/16S473J

> Fuse 10A CEK1208 R 932 (B,65,110) RS1/16S104J


AR401 (A,161,110) Arrester DSP-201M-S00B R 933 (A,55,116) RD1/4PU102J
FM/AM Tuner Unit CWE1954 R 934 (B,61,110) RS1/16S473J
F R 935 (B,55,106) RS1/16S473J
RESISTORS R 936 (B,57,110) RS1/16S223J

R 301 (B,93,104) RS1/16S153J R 940 (B,86,81) RS1/16S104J


R 353 (B,144,128) RS1/16S821J R 941 (B,89,81) RS1/16S104J
DEH-2800MP/XN/EW
50
1 2 3 4
5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 961 (B,67,78) RS1/16S102J C 991 (B,17,63) CKSRYB473K50
R 962 (B,62,78) RS1/16S183J C 992 (A,17,54) CEJQ101M10
R 991 (A,20,61) RD1/4PU271J

R 992 (A,15,68) RD1/4PU221J B


Unit Number : (DEH-2800MP/XN/EW,
A

CAPACITORS
DEH-2800MPB/XN/EW, DEH-281MP/XN/
C 151 (B,160,73) CKSRYB224K10
C 152 (B,160,75) CKSRYB224K10
EW)
C 153 (B,130,69) CKSRYB105K6R3 Unit Name : Keyboard Unit
C 154 (B,142,74) CKSRYB105K6R3
C 165 (B,136,91) CKSRYB104K16 MISCELLANEOUS
C 166 (A,134,92) CEJQ470M10 IC 1801 (B,32,100) IC PD6340A
C 167 (A,128,92) CEJQ100M16 D 1803 (A,43,67) LED SML-310VT B
C 301 (B,119,108) CKSQYB474K16 D 1804 (A,43,79) LED SML-310VT
C 302 (B,128,111) CKSQYB474K16 D 1805 (A,43,91) LED SML-310VT
C 303 (B,131,122) CKSQYB474K16 D 1806 (A,28,29) LED SML-310VT

C 304 (B,123,107) CKSQYB474K16 D 1807 (A,43,39) LED SML-310VT


C 305 (B,119,113) CKSRYB474K10 D 1808 (A,43,55) LED SML-310VT
C 306 (B,131,114) CKSRYB474K10 D 1809 (A,28,42) LED SML-310VT
C 307 (B,134,124) CKSRYB474K10 D 1810 (A,29,50) LED NESW505C-5273
C 308 (B,126,109) CKSRYB474K10 D 1812 (A,17,12) LED SML-310VT

C 309 (B,136,132) CKSQYB225K10 D 1813 (A,31,12) LED SML-310VT


C 310 (B,137,136) CKSQYB225K10 D 1814 (A,12,154) LED SML-310VT
C 311 (A,97,122) CEJQ2R2M50 D 1815 (A,17,168) LED SML-310VT C
C 312 (A,104,125) CEJQ100M16 D 1816 (A,31,168) LED SML-310VT
C 313 (B,100,142) CKSRYB104K16 D 1817 (A,43,127) LED SML-310VT

C 353 (A,134,120) CEJQ2R2M50 D 1818 (A,43,115) LED SML-310VT


C 354 (A,134,110) CEJQ2R2M50 D 1819 (A,43,103) LED SML-310VT
C 401 (B,160,69) CKSRYB103K50 D 1820 (A,28,136) LED SML-310VT
C 403 (A,151,58) CEJQ470M6R3 D 1821 (A,22,144) LED SML-310VT
C 404 (A,151,95) CEJQ101M10 D 1823 (A,42,140) LED SML-310VT

C 405 (B,167,97) CKSRYB103K50 D 1824 (A,33,144) LED SML-310VT


C 407 (B,159,60) CKSQYB475K6R3 D 1825 (A,28,152) LED SML-310VT
C 409 (B,147,56) CCSRCH470J50 X 1801 (B,39,90) Ceramic Resonator 5.00MHz CSS1547
C 420 (B,108,43) CCSRCH470J50 LCD(DEH-2800MP/XN/EW) CAW1900 D
C 451 (A,132,132) CEJQ330M10 LCD(DEH-2800MPB/XN/EW) CAW1903

C 551 (B,68,120) CKSRYB103K50 LCD(DEH-281MP/XN/EW) CAW1901


C 552 (B,65,123) CKSRYB103K50
C 601 (B,69,83) CKSRYB103K50 RESISTORS
C 604 (B,98,75) CCSRCH200J50
C 605 (B,102,75) CCSRCH200J50
R 1801 (B,28,66) RS1/16S222J
R 1802 (B,30,66) RS1/16S222J
C 608 (B,91,48) CCSRCH101J50
R 1807 (B,27,29) RS1/4SA471J
C 610 (A,101,82) CEJQ4R7M35
R 1808 (B,31,42) RS1/4SA471J
C 613 (B,100,78) CKSRYB105K6R3
R 1809 (B,24,42) RS1/4SA681J
C 651 (B,42,40) CKSRYB105K10
C 670 (B,44,42) CCSRCH221J50 E
R 1810 (B,42,98) RS1/16S104J
R 1811 (B,21,29) RS1/4SA681J
C 801 (B,104,25) CKSRYB105K6R3
R 1812 (B,30,123) RS1/4SA471J
C 832 (B,49,13) CKSRYB104K16
R 1813 (B,35,128) RS1/4SA471J
C 901 (A,36,140) CEAT332M16(P45)
R 1814 (B,32,133) RS1/4SA681J
C 911 (A,16,96) CEJQ470M10
C 912 (B,12,133) CKSRYB103K50
R 1815 (B,40,136) RS1/4SA471J
C 913 (A,19,137) CEAT331M16
C 921 (A,25,66) 330µF/16V CCH1326
CAPACITORS
C 922 (A,24,82) CEJQ101M16
C 923 (B,23,85) CKSRYB103K50 C 1801 (B,42,102) CKSRYB103K50
C 961 (B,56,85) CKSRYB473K50 C 1802 (A,28,45) CKSRYF104Z25
F
C 962
C 981
C 983
(B,60,75)
(B,135,25)
(A,144,38)
CKSRYB105K6R3
CKSRYB334K10
CEJQ470M10
B
Unit Number : (DEH-2820MP/XN/EW)

DEH-2800MP/XN/EW
5 6 7 8
51
1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Unit Name : Keyboard Unit X 201 (B,28,57) Ceramic Resonator 16.934MHz CSS1603
X 701 (A,24,37) Ceramic Resonator 4.000MHz CSS1652
S 901 (A,57,57) Switch(HOME) CSN1067
A
MISCELLANEOUS S 903 (B,23,78) Switch(DSCSNS) CSN1067

IC 1801 (B,32,100) IC PD6340A S 904 (B,42,87) Switch(12EJ) CSN1068


D 1803 (A,43,67) LED SML-310PT S 905 (B,28,88) Switch(8EJ) CSN1068
D 1804 (A,43,79) LED SML-310PT
D 1805 (A,43,91) LED SML-310PT
D 1806 (A,28,29) LED SML-310PT
RESISTORS

R 101 (B,61,92) RS1/10SR2R4J


D 1807 (A,43,39) LED SML-310PT
R 102 (B,63,92) RS1/10SR2R4J
D 1808 (A,43,55) LED SML-310PT
R 103 (B,63,89) RS1/10SR2R7J
D 1809 (A,28,42) LED SML-310PT
R 104 (A,52,73) RS1/16SS102J
D 1810 (A,29,50) LED NESW505C-5273
R 201 (B,44,57) RS1/16SS102J
D 1812 (A,17,12) LED SML-310PT
B
R 202 (A,38,62) RS1/16SS473J
D 1813 (A,31,12) LED SML-310PT
R 203 (A,37,62) RS1/16SS473J
D 1814 (A,12,154) LED SML-310PT
R 214 (A,46,79) RS1/16SS472J
D 1815 (A,17,168) LED SML-310PT
R 216 (A,46,81) RS1/16SS472J
D 1816 (A,31,168) LED SML-310PT
R 221 (A,44,81) RS1/16SS103J
D 1817 (A,43,127) LED SML-310PT

R 222 (A,45,81) RS1/16SS103J


D 1818 (A,43,115) LED SML-310PT
R 225 (B,52,78) RS1/16SS103J
D 1819 (A,43,103) LED SML-310PT
R 226 (B,52,77) RS1/16SS393J
D 1820 (A,28,136) LED SML-310PT
R 227 (A,44,75) RS1/16SS562J
D 1821 (A,22,144) LED SML-310PT
R 228 (A,46,72) RS1/16SS122J
D 1823 (A,42,140) LED SML-310PT

R 229 (A,44,72) RS1/16SS472J


C D 1824 (A,33,144) LED SML-310PT
R 232 (A,46,75) RS1/16SS122J
D 1825 (A,28,152) LED SML-310PT
R 241 (B,26,63) RS1/16SS333J
X 1801 (B,39,90) Ceramic Resonator 5.00MHz CSS1547
R 243 (B,26,62) RS1/16SS333J
LCD CAW1900
R 245 (B,26,69) RS1/16SS333J
RESISTORS R 248 (B,55,74) RS1/16SS105J
R 307 (A,19,20) RS1/16SS183J
R 1801 (B,28,66) RS1/16S222J
R 308 (A,17,20) RS1/16SS183J
R 1802 (B,30,66) RS1/16S222J
R 309 (A,18,18) RS1/16SS183J
R 1807 (B,27,29) RS1/4SA471J
R 310 (A,17,16) RS1/16SS183J
R 1808 (B,31,42) RS1/4SA471J
R 1809 (B,24,42) RS1/4SA681J
R 601 (B,30,47) RS1/16S101J
R 602 (B,28,50) RS1/16S101J
D R 1810 (B,42,98) RS1/16S104J
R 606 (B,20,54) RS1/16S0R0J
R 1811 (B,21,29) RS1/4SA681J
R 701 (B,26,44) RS1/16SS221J
R 1812 (B,30,123) RS1/4SA471J
R 707 (B,32,45) RS1/16SS473J
R 1813 (B,35,128) RS1/4SA471J
R 1814 (B,32,133) RS1/4SA681J
R 709 (A,36,35) RS1/16SS222J
R 710 (B,41,46) RS1/16SS102J
R 1815 (B,40,136) RS1/4SA471J
R 712 (A,45,57) RS1/16SS222J
R 713 (B,40,57) RS1/16SS222J
CAPACITORS R 716 (B,29,37) RS1/16SS472J

C 1801 (B,42,102) CKSRYB103K50 R 724 (B,31,36) RS1/16S473J


C 1802 (A,28,45) CKSRYF104Z25 R 726 (B,23,47) RS1/16SS103J
E R 727 (B,31,42) RS1/16SS473J

C
Unit Number : CWX3176
R
R
729
730
(B,20,48)
(B,20,46)
RS1/16SS223J
RS1/16SS473J

Unit Name : CD Core R 740 (A,38,59) RS1/16SS222J


R 746 (A,13,38) RS1/16SS104J
Unit(S10.5COMP1) R 750 (A,40,66) RS1/16SS473J
R 902 (A,20,36) RS1/16SS221J
MISCELLANEOUS R 905 (A,21,36) RS1/16SS221J

R 906 (B,20,36) RS1/16SS221J


IC 201 (B,39,70) IC UPD63763CGJ
R 907 (B,16,62) RS1/16SS0R0J
IC 203 (A,12,16) IC NJM2886DL3-33
R 908 (B,16,64) RS1/16SS0R0J
IC 301 (A,28,18) IC BA5835FP
F R 911 (B,20,32) RS1/16SS0R0J
IC 701 (A,32,48) IC PE5505A
Q 101 (B,60,89) Transistor 2SA1577
CAPACITORS
Q 701 (B,24,41) Transistor UN2111

DEH-2800MP/XN/EW
52
1 2 3 4
5 6 7 8

Circuit Symbol and No. Part No.


C 103 (B,57,83) CEVW101M16
C 108 (A,47,66) CKSSYB104K10
C 201 (B,46,56) CKSSYB102K50
C 202 (B,47,58) CKSSYB104K10 A
C 204 (B,35,48) CEVW220M6R3

C 205 (A,34,63) CKSSYB104K10


C 208 (B,34,54) CKSSYB104K10
C 209 (B,31,57) CKSSYB104K10
C 210 (A,31,66) CKSRYB105K10
C 216 (B,53,77) CKSSYB332K50

C 217 (B,52,79) CKSSYB104K10


C 218 (B,52,76) CKSSYB473K10
C 219 (B,52,74) CKSSYB104K10
C 220 (A,46,77) CKSSYB182K50
C 221 (B,51,74) CKSSYB104K10 B

C 222 (A,46,73) CCSSCH560J50


C 223 (A,44,74) CCSSCH4R0C50
C 224 (B,52,68) CKSSYB104K10
C 225 (A,47,67) CKSSYB103K16
C 226 (A,49,67) CCSSCH680J50

C 227 (A,48,65) CCSSCH470J50


C 228 (A,46,62) CKSSYB103K16
C 232 (A,12,31) CKSRYB105K10
C 237 (A,31,67) CKSSYB104K10
C 239 (A,46,74) CCSSCH220J50
C
C 246 (A,42,80) CKSSYB104K10
C 250 (A,42,81) CKSRYB102K50
C 251 (A,41,83) CKSRYB102K50
C 303 (A,18,20) CKSSYB472K25
C 304 (A,17,17) CKSSYB103K16

C 307 (A,34,15) CKSSYB104K10


C 308 (A,17,30) CKSRYB105K10
C 601 (B,25,50) CCSRCH102J50
C 602 (B,26,51) CCSRCH102J50
C 701 (B,25,47) CKSSYB104K10

C 703 (B,28,42) CKSSYB103K16 D


C 706 (B,34,43) CKSSYB104K10
C 707 (A,36,57) CKSSYB104K10
C 714 (A,24,41) CKSSYB104K10
C 722 (B,29,45) CKSQYB475K6R3

C 903 (B,14,54) CKSSYB471K50


C 907 (B,14,62) CKSSYB103K16

Miscellaneous Parts List


Pickup Unit(P10.5)(Service) CXX1942
M 1 Motor Unit(SPINDLE) CXC6742 E
M 2 Motor Unit(LOADING/CARRIAGE) CXC4026

DEH-2800MP/XN/EW
5 6 7 8
53
1 2 3 4

6. ADJUSTMENT
6.1 CD ADJUSTMENT
A

1) Cautions on adjustments 2) Test mode


• In this product the single voltage (3.3V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65V) • To enter the test mode.
instead of the GND. While pressing the 4 and 6 keys at the same time, reset.
If you should mistakenly short the REFO1 with the GND • To exit from the test mode.
during adjustment, accurate voltage will not be obtained, Turn off the ACC and back up.
and the servo’s misoperation will apply excessive shock
to the pickup. To avoid such problems: Notes:
a. Do not mix up the REFO1 with the GND when a. During ejection, do not press any other keys than the
connecting the (-) probe of measuring instruments. EJECT key until the loaded disc is ejected.
B Especially on an oscilloscope, avoid connecting the (-) b. If you have pressed the (→) key or (←) key during focus
probe for CH1 to the GND. search, turn off the power immediately to protect the
b. In many cases, measuring instruments have the same actuator from damage caused by the lens stuck.
potential as that for the (-) probe. Be sure to set the c. For the TR jump modes except 100TR, the track jump
measuring instruments to the floating state. operation will continue even if the key is released.
c. If you have mistakenly connected the REFO1 to the GND, d. For the CRG move and 100TR jump modes, the tracking
turn off the regulator or the power immediately. loop will be closed at the same time when the key is
released.
• Before mounting and removing filters or leads for e. When the power is turned off and on, the jump mode
adjustment, be sure to turn off the regulator. is reset to the single TR (91), the RF amp gain is set to 0dB,
and the auto-adjustment values are reset to the default
• For stable circuit operation, keep the mechanism settings.
C operating for about one minute or more after the
regulator is turned on.

• In the test mode, any software protections will not


work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.

• The RFI and RFO signals with a wide frequency range


are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.

• The load and eject operation is not guarantied with the


D
mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.

DEH-2800MP/XN/EW
54
1 2 3 4
5 6 7 8

- Flow Chart
[Key] [4] + [6] + Reset or
[4] + [6] + BU + ACC
Contents Test Mode In

Display A

[CD] or [SOURCE]
Source On

TRK MIN SEC

[BAND] [3] [2] [4]


Power On Power On RF AMP *1 SPINDLE *9
(T.Offset is adjusted) (T.Offset is not adjusted) Gain switching Speed switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99 GG GG GG SP SP SP

[BAND] [3] [6] [1] [>] [<] [2]


[5]
Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
S curve check *2 Close *8 *8 switching *3 Gop Mode *10 B
Gop Mode switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??
OL OL OL

[BAND] [1] [6] [3] [>] [<] [2]


Power Off T.Close & AGC T.Close RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??

[BAND] [1] [3] [6] *5 [>] [<] [2]


Power Off F,T,RF AGC*7 F,T AGC / F.Bias CRG/TR jump CRG/TR Jump + CRG/TR Jump - Tracking Open
F.Bias display switching RF AGC value switching *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X

*6 C

[BAND] [2]
Power Off Tracking Open

TRK MIN SEC 8X 8X 8X


or 9X 9X 9X

*1) TYP → + 6 dB → + 12 dB Operation


TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [Key] Test Mode
[BAND] Power On/Off
[>] CRG + / TR Jump +
*2) Focus Close → S Curve check setting → F EQ measurement setting (Direction of the external surface)
TRK
00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 [<] CRG - / TR Jump -
(TRK99MIN99SEC99) (Direction of the internal surface) D
[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the [2] RF Gain switching / Offset adjustment display /
order of the original display
T.Balance adjustment / T. Open
[3] F. Close,S Curve / Rough Servo and RF AGC /
*4) 1TR/4TR/10TR/32TR/100TR F,T,RF AGC
*5) Single → 4TR → 10TR → 32TR → 100TR → CRG Move [4] SPDL 1X/2X switching
9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86) As for the double speed(2x), audio output cannot be
supported.
*6) Only at the time of CRG move, 100TR jump [5] Error Rate measurement
ON : ERR 30Counts Start
BER display data[%]
*7) TRK/MIN/SEC → F.AGC → T.AGC Gain → F.Bias → RF AGC
[6] F. Mode switching / Tracking Close / CRG•TR E
Jump Switching
*8) CRG motor voltage = 2 [V]

*9) TYP (1X) → 2X → 1X *10) OFF(TYP) → FORCUS → TRACKING


TRK MIN SEC TRK
22MIN22SEC22 TRK
11MIN11SEC11 TRK MIN SEC TRK
70MIN70SEC70 TRK
71MIN71SEC71

• As for the double speed (2x), audio output cannot be supported

*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for F
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.

DEH-2800MP/XN/EW
5 6 7 8
55
1 2 3 4

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

B • Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO1
• Disc • TCD-782
• Mode • TEST MODE

CD CORE UNIT(S10.5COMP1)
C

L.P.F.
REFO1
E Xch Ych
E 100kΩ
F
Oscilloscope
VREF 390pF

F 100kΩ

VREF 390pF

D L.P.F.

• Checking Procedure
1. In test mode, load the disc and switch the 3V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

DEH-2800MP/XN/EW
56
1 2 3 4
5 6 7 8

Grating waveform Ech → Xch 20mV/div, AC


Fch → Ych 20mV/div, AC
A

0° 30°

45° 60°

75° 90°

DEH-2800MP/XN/EW
5 6 7 8
57
1 2 3 4

6.3 ERROR MODE


- Error Messages
A If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method


1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.

2) Head unit display examples


B
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display


ERROR–xx ERR–xx E–xx

(2) Error Code List


Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
C munication Error → Failure on home switch or CRG move mechanism.
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
→ Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG → Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
D → Damages or stains on disc, or excessive vibrations on REWRITABLE.
30 Electricity Search Time Out Failed to reach target address.
→ CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
→ Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
→ Failure on SW transistor or power supply (failure on connector).
E Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.

DEH-2800MP/XN/EW
58
1 2 3 4
5 6 7 8

6.4 SYSTEM MICROCOMPUTER TEST PROGRAM(DEH-281MP/XN/EW)

A
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled),
shift the TESTIN IC601(Pin 15) terminal to H. The clock signal is output from the PCL terminal IC601(Pin 14).
The frequency of the clock signal is 786.432 kHz that is one 16th of the fundamental frequency. The clock signal should
be 786.432 kHz ± 31.5 Hz. If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.

DEH-2800MP/XN/EW
5 6 7 8
59
1 2 3 4

7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
A

- Removing the Case (not shown)

1. Remove the Case.

CD Mechanism Module
- Removing the CD Mechanism Module (Fig.1)

1 Remove the four screws.


B
Disconnect the connector and then remove the 1
CD Mechanism Module.
1

- Removing the Grille Assy (Fig.1)

2 Release the two latchs and then remove


the Grille Assy.
1
C
2 1 2

Grille Assy Fig.1

- Removing the Tuner Amp Unit (Fig.2)

1 Remove the screw.


2
D 2
2
2 Remove the three screws.

3 Straighten the tabs at three locations


indicated and then remove
the Tuner Amp Unit.

3 3 3

Tuner Amp Unit Fig.2


F

DEH-2800MP/XN/EW
60
1 2 3 4
5 6 7 8

- How to hold the Mechanism Unit


1. Hold the Upper and Lower Frames.
2. Do not hold the front portion of the Upper
Frame, because it is not very solid. A

Do not squeeze this area.

- Removing the Upper and Lower Frames


1. With a disc inserted and clamped in the a
B
mechanism, remove the two Springs (A), Upper Frame
the six Springs (B), and the four Screws. B
2. Turn the Upper Frame using the part "a" as
a pivot, and remove the Upper Frame. C
3. While lifting the Carriage Mechanism,
B
remove it from the three Dampers.
Caution: When assembling, be sure to apply
some alcohol to the Dampers and assemble B
the mechanism in a clamped state.

B
B

A
Damper
Damper D
A
Carriage Mechanism Lower Frame

DEH-2800MP/XN/EW
5 6 7 8
61
1 2 3 4

- How to remove the CD Core Unit


1. Apply Shorting Solder to the flexible cable of Shorting Solder
the Pickup, and disconnect it from the
A connector.
2. Unsolder the four leads, and loosen the
Screw.
3. Remove the CD Core Unit.
Caution: When assembling the CD Core Unit,
assemble it with the SW in a clamped state
so as not to damage it.

Screw

B
CD Core Unit

Solder

- How to remove the Pickup Unit


1. Make the system in the carriage mechanism mode, and have it clamped.
2. Remove the CD Core Unit and remove the leads from the Inner Holder.
3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm.
C 4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw.
Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner
Holder.
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load
Carriage Motor Assy, do not make them loose over the Feed Screw.

Poly Washer Change Arm

Pickup Lock Arm


Inner Holder
Feed Screw

Planet Gear
Pickup Rack

Chassis

Pickup

DEH-2800MP/XN/EW
62
1 2 3 4
5 6 7 8
7.1.2 CONNECTOR FUNCTION DESCRIPTION

16 14 12 10 8 6 4 2
15 13 11 9 7 5 3 1

ANTENNA JACK REAR OUTPUT WIRED REMOTE CONTROL ADAPTORS


(DEH-2800MP/XN/EW,
DEH-2800MPB/XN/EW,
DEH-2820MP/XN/EW)

C
Pin No. Pin No.
1 B.UP 9 RL-
2 GND 10 FL-
3 ACC 11 RL+
4 NC 12 FL+
5 NC 13 RR-
6 B.REMOTE 14 FR-
7 NC 15 RR+ D

8 NC 16 FR+

DEH-2800MP/XN/EW
5 6 7 8
63
1 2 3 4

7.2 PARTS
7.2.1 IC
- Pin Functions (PE5517A, PE5518A)
A
Pin No. Pin Name I/O Function and Operation
1 MODEL1 I Model select input
2,3 NC Not used
4 AVSS GND
5,6 NC Not used
7 AREF1 VDD
8 KYDT I Display microcomputer data input
9 DPDT O Display microcomputer communication data output
10 NC Not used
11 TUNPDI I PLL data input
12 TUNPDO O PLL data output
B 13 TUNPCK O PLL clock output
14 PCL O Clock adjustment output
15 TESTIN I Test program input
16 BSI I Bus serial data input
17 BDATA O Bus serial output data
18 BSCK O Bus serial clock output
19 DORAON Not used
20 NC Not used
21 swvdd O Display microcomputer chip select output
22 ILMPW O Illumination power output
23-31 NC Not used
32 DALMON O Output for dark current reduction circuit / Stand-by mode : L output
C 33 VSS GND
34 BRST O Bus reset output
35 BRXEN I/O Bus RX enable input/output
36 CDRESET O CD microcomputer reset signal output
37 ROMDATA O ROM collection data output
38 ROMCLK O ROM collection clock output
39 ROMCS O ROM collection chip select output
40 RECEIVE O RDS decoder receiving output
41,42 NC Not used
43 SYSPW O System power output
44-46 NC Not used
47 STRKEY2 I Wired remote control input 2
D
48 MUTE O System mute output
49 ANTPW O Auto antenna control output
50 NC Not used
51 VST O E.VOL strobe output
52 VDT O E.VOL data output
53 VCK O E.VOL clock output
54 NC Not used
55 TUNPCE2 O PLL chip enable output 2
56 TUNPCE O PLL chip enable output
57 RDT I RDS LK input
58 RDSLK I RDS clock input
E 59 RDS57K I RDS 57K input
60 RESET Reset
61 LDET I PLL lock detection input
62 RCK I RDS clock input
63 asens I ACC sense input
64 bsens I Back up sense input
65 dsens I Grille detach sense input
66 source I Source sense input
67 VSS GND
68 VDD VDD

DEH-2800MP/XN/EW
64
1 2 3 4
5 6 7 8

Pin No. Pin Name I/O Function and Operation


69,70 X2,1 Crystal oscillator connection pin
71 IC(VPP) GND
72 NC Not used A
73 VSS VSS
74 AVDD VDD
75 AVREF1 VDD
76 SL I Signal level input
77,78 NC Not used
79 BSRQ I Bus slave service request
80 STRKEY1 I Wired remote control input 1

*PE5517A, *PE5518A
61
80

IC's marked by * are MOS type. B


1 60
Be careful in handling them because they are very
liable to be damaged by electrostatic induction.

20 41
21

40

PAL007B
Reference

Protector;
Thermal

sw_vcc

amp_vcc
D
amp_vcc

+- -+ +- -+ +- -+ +- -+ sw_vcc
Detection

Detection

Detection
Detection
Offset

Offset

Offset
Offset

stby
Stand-by
Over voltage

Circuit
Protector;

Over current limit


Short circuit
Protector;

Mute circuit
Protector;

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
TAB

OUT1+

OUT3+
OUT2+

VCC

OUT1-

P-GND1

S-GND

IN4

IN3

AC-GND

OUT4+

MUTE

OUT4-

P-GND4
STBY

IN2

SWITCH
VCC
P-GND2

OUT2-

SVR

IN1

P-GND3

OUT3-

DEH-2800MP/XN/EW
5 6 7 8
65
F
E
B
A

D
C

66
DATA
STB
Vcc
GND

CLK
Vref
PML014A

1
1

IN1_L Digital Supply


IN2_L &
IN3_L Block Reference

IN4+_L
- Block Diagram

Isolator
IN4-_L Gain Auto Primary
Adjuster Zero
IN4-_R Volume
Isolator

Input Selector
IN4+_R
Secondary
IN3_R Front_L
IN2_R Volume
IN1_R Anti-Alias
Filter

Secondary
Rear_L

2
2

Volume

Anti-Radiation
TRE MID BASS LOUDNESS
Filter
Secondary
Front_R
Volume

Secondary

DEH-2800MP/XN/EW
Rear_R
Volume

3
3

Vcc
Rear_L
IN4-_L

GND
IN4+_L
IN3_L
IN2_L
IN1_L

Vref
Front_L

9
8
7
6
5
4
3
2
1

10
- Pin Layout

4
4

11
12
13
14
15
16
17
18
19
20

CLK
STB

DATA
IN3_R
IN2_R
IN1_R

IN4-_R
IN4+_R

Rear_R
Front_R
5 6 7 8

NJM2885DL1-33
A

Thermal
Protection

-+
Bandgap
Reference

1 2 3

IN GND OUT

- Pin Functions(PD6340A)
Pin No. Pin Name I/O Function and Operation
1-5 SEG4-0 O LCD segment output C
6-9 COM3-0 O LCD common output
10 VLCD LCD drive power supply
11-14 KST3-0 O Key strobe output
15,16 KDT0,1 I Key data input (analogue input)
17 REW I Remote control reception input
18 DPDT I Display data input
19 NC Not used
20 KYDT O Key data output
21 MODA GND
22 X0 Crystal oscillator connection pin
23 X1 Crystal oscillator connection pin
24 VSS GND D
25,26 KDT2,3 I Key data input
27 NC Not used
28 KST4 O Key strobe output
29-32 NC Not used
33-55 SEG35-13 O LCD segment output
56 VDD Power supply
57-64 SEG12-5 O LCD segment output

* PD6340A
1

16

E
64 17

49 32
48

33

DEH-2800MP/XN/EW
5 6 7 8
67
1 2 3 4

- Pin Functions (UPD63763CGJ)


Pin No. Pin Name I/O Function and Operation
1 D.VDD Power supply for digital circuits
A 2 D1.GND Ground for 1.6 V digital circuits
3 reset I Input of reset
4-8 AB12-8 I Address bus 12-8 from the microcomputer
9-16 AD7-0 I/O Address/data bus 7-0 to the microcomputer
17 cs I Chip selection
18 ASTB I Address strobe
19 read I Control signals(read)
20 write I Control signals(write)
21 wait O Control signals(wait)
22 INTQ O Interruption signals to the external microcomputer
23,24 IFMODE0,1 I Switching the microcomputer I/F 0, 1
25 D1.VDD Power supply for 1.6 V digital circuits
B
26 DA.VDD Power supply for DAC
27 ROUT O Output of audio for the right channel
28 DA.GND Ground for DAC
29 REGC Connected to the capacitor for band gap
30 DA.GND Ground for DAC
31 LOUT O Output of audio for the left channel
32 DA.VDD Power supply for DAC
33 X.VDD Power supply for the crystal oscillator
34 XTAL I Connected to the crystal oscillator(16.9344 MHz)
35 xtal O Connected to the crystal oscillator(16.9344 MHz)
36 X.GND Ground for the crystal oscillator
C 37 VDDREG15 Control of 1.6 V regulator
38 PWMSW0 I Setup 0 for PWM output(SD, MD)
39-41 TEST3-1 I Connected to Ground
42 PWMSW1 I Setup 1 for PWM output(FD, TD)
43 TESTEN I Connected to Ground
44 D1.GND Ground for 1.6 V digital circuits
45 DIN I Input of audio data
46 DOUT O Output of audio data
47 SCKIN I Clock input for audio data
48 SCKO O Clock output for audio data
49 LRCKIN I Input of LRCK for audio data
50 LRCK O Output LRCK for audio data
D 51 xtalen I Permission to oscillate 16.9344 MHz
52 D1.VDD Power supply for 1.6 V digital circuits
53 RFCK/HOLD O Output of RFCK/HOLD signal
54 WFCK/MIRR O Output of WFCK/MIRR signal
55 PLCK/RFOK O Output of PLCK/Output of RFOK
56 LOCK/RFOK O Output of LRCK/Output of RFOK
57 C1D1/C8M/(RA13) O Information on error correction/C8M : 8 MHz
58 C1D2/C16M/(RA12) O Information on error correction/C16M : 16 MHz
59 C2D1/RMUTE O Information on error correction/Mute for Rch
60 C2D2/LMUTE O Information on error correction/Mute for Lch
61 C2D3/SHOCK O Information on error correction/Detection of vibration
62 D1.GND Ground for 1.6 V digital circuits
E 63 C33M O Output of 33.8688 MHz(CLK for SDRAM)
64 (rcs) O DRAM cs
65 RA11 O Output of DRAM address 11
66 (CKE) O Output of DRAM CKE
67 ras O Output of DRAM ras
68 cas)(LDQM) O Output of DRAM lower cas(LDQM)
69 cas!(UDQM) O Output of DRAM upper cas(UDQM)

DEH-2800MP/XN/EW
68
1 2 3 4
5 6 7 8

Pin No. Pin Name I/O Function and Operation


70 we O Output of DRAM we
71 oe(cas) O Output of DRAM oe(cas)
72 D.GND Ground for digital circuits A
73-88 RDB0-15 I/O Input/output of DRAM data0-15
89-99 RA0-10 O Output of DRAM address0-10
100 D.VDD Power supply for digital circuits
101 FD+ O Output of focus drive PWM +
102 FD- O Output of focus drive PWM -
103 TD+ O Output of tracking drive PWM +
104 TD- O Output of tracking drive PWM -
105 SD+ O Output of thread drive PWM +
106 SD- O Output of thread drive PWM -
107 MD+ O Output of spindle drive PWM +
108 MD- O Output of spindle drive PWM -
B
109 REFOUTSV O REFOUT for servo
110 AD.VDD Power supply for ADC
111 EFM O Output of EFM signals
112 ASY I Input of asymmetry
113 ATEST O Analog tests
114 RFI I Input of RF
115 AD.GND Ground for the analog system
116 AGCO O Output of RF
117 C3T O Connection to the capacitor for detecting 3T
118 AGCI I Input of AGC
119 RFO O Output of RF(AGC)
120,121 EQ2,1 I Equalizer 2, 1 C
122 RF2- I Reversal input of RF2
123 RF- I Reversal input of RF
124 A.GND Ground for the analog system
125 A I Input of A
126 C I Input of C
127 B I Input of B
128 D I Input of D
129 F I Input of F
130 E I Input of E
131 VREFIN I Input of reference voltage
132 A.VDD Power supply for the analog system
133 REFOUT O Output of reference voltage D
134 REFC I Connected to the capacitor for output of REFOUT
135 FE- I Reversal input of FE
136 FEO O Output of FE
137 ADIN I Input of FE, TE A/D converter
138 TE- I Reversal input of TE
139 TEO O Output of TE
140 TE2 O TE2
141 TEC I TEC
142 LD O Output of LD
143 PD I Input of PD
144 D.GND Ground for digital circuits
E

* UPD63763CGJ
109
144

1 108

36 73
F
37

72

DEH-2800MP/XN/EW
5 6 7 8
69
1 2 3 4

- Pin Functions (PE5505A)


Pin No. Pin Name I/O Format Function and Operation
1 AVREF A power supply / Positive power supply(5V)
A 2 AVSS A power supply GND
3 testin I Chip check test program starting input
4 CLAMP Not used
5 EVDD E power supply / Positive power supply
6 FMODE For flash rewriting / L : flash rewriting mode
7 FLRQ For flash rewriting / Reset voltage control
8 IC/FLMD0 IC : VSS direct connection/FLMOD0 : Pull-down
9 VDD Positive power supply(5V)
10 REGC Connected to the capacity stabilizing output of the regulator
11 VSS GND
12 X1 I Oscillator connection for mainclock
13 X2 Oscillator connection for mainclock
B
14 reset I System reset input
15 XT1 I Connected to the oscillator for subclock(connected to VSS via the resistor)
16 XT2 Connected to the oscillator for subclock(Open)
17 PULLDOWN I Connected to EVDD or EVSS via the resistor
18 ejsw Not used
19 xint I C CD LSI interruption signal input
20 NC Not used
21 brst I Bus reset input
22 BSI I Bus serial data input
23 BSO O C Bus serial data output
24 bsck I/O /C Bus serial clock input/output
C 25 FTxD O C For flash rewriting(transmitted signal)
26 FRxD I For flash rewriting(received signal)
27 BRXEN I/O /C Bus RX enable input/output
28 bsrq I/O /C Bus serial clock input/output
29 dspok Not used
30 DSCSNS I C Disc state sense input
31 8EJ(S905) I C input of detection of 8 cm disc ejection
32 12EJ(S904) I C input of detection of 12 cm disc ejection
33 EVSS E power supply GND
34 EVDD E power supply / Positive power supply
35,36 SRAMLEVEL0,1 O SRAM level meter output
37 EMPH O C Emphasis information output
D 38 emph Not used
39 CDMUTE Not used
40 LOEJ Not used
41 CLCONT O Driver input switching output
42 HOME I Home SW sense input
43 adena O C A/D reference voltage supply control output
44 LRCKOK O C (DOUT mute output)
45 SRAMLEVEL2 O C SRAM level meter output
46 CD3VON(MCKRQ) O C CD + 3.3 V power supply control output(Digital output : MCKRQ)
47 CONT O C Servo driver power supply control output
48 xrst O C CD LSI reset control output
49 VDCONT O C VD power supply control output
E
50 xsi I CD LSI serial data input
51 xso O C CD LSI serial data output
52 xck O C CD LSI serial clock output
53 xwait I C CD LSI wait control signal input
54 XASTB O C CD LSI address strobe output
55 AD0 O C Address/data Bus 0
56 INT Not used

DEH-2800MP/XN/EW
70
1 2 3 4
5 6 7 8

Pin No. Pin Name I/O Format Function and Operation


57 ROMDATA I/O E2PROM data input/output
58 ROMCK O E2PROM clock output
59 ROMCS O C E2PROM chip selection output A
60,61 NC Not used
62 CLKOUT Not used
63 LOCK I Spindle lock input
64-68 NC Not used
69 BVSS B power supply GND
70 BVDD B power supply / Positive power supply
71-75 NC Not used
76 FLMD1 I/O /C Address/Data Bus 5
77-90 NC Not used
91-93 A/D Not used
94 csens Not used
B
95 TYPE_A/D Not used
96,97 NC Not used
98 TEMP Not used
99 VDSENS I VD power supply short sense input
100 DSCSNS Not used

* PE5505A
Format meaning
100

76

C C MOS
1 75

25 51
26

50

NJM2886DL3-33 D

Thermal
Protection

Bandgap
Reference
-+

1 2 3 4 5

CONTROL VIN GND VO NC

DEH-2800MP/XN/EW
5 6 7 8
71
1 2 3 4

- FM/AM Tuner Unit


7 6 13 5 10 9 8 11 14 18 19 20 21

CE2

ROM_VDD

SL

DI
CK
CE1

LDET

DO

RDS_CK

RDS_DATA

RDS_LOCK

RDS_HSLK
NC
A

IC 3 EEPROM IC 5

5.0V 5V 3.3V

OSC LPF

AM ANT FMRF
1 ATT
Rch
24
IC 2
IC 1 2.5V
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
B RDS DECODER
RF adj
ANT adj

T51 CF52
AUDIOGND

IC 4
OSCGND

VDD_3.3


RFGND

3.3V 3.3V 2.5V 2.5V


DGND

VCC
NC

2 12 15 22 16 4 17

No. Symbol I/O Explain


C 1 AMANT I AM antenna input AM antenna input high impedance AMANT pin is connected with
an all antenna by way of 4.7µH. (LAU type inductor) A series circuit
including an inductor and a resistor is connected with RF ground for
the countermeasure against the hum of power transmission line.
2 RFGND RF ground Ground of antenna block
3 FMANT I FM antenna input Input of FM antenna 75Ω Surge absorber(DSP-201M-S00B) is necessary.
4 VCC power supply The power supply for analog block. D.C 8.4V ± 0.3V
5 SL O signal level Output of FM/AM signals level
6 CE2 I chip enable-2 Chip enable for EEPROM ”Low” active
7 NC non connection Not used
8 CE1 I chip enable-1 Chip enable for AF•RF ”High” active
D
9 CK I clock Clock
10 DI I data in Data input
11 LDET O lock detector “Low” active
12 OSCGND osc ground Ground of oscillator block
13 ROM_VDD power supply Power supply for EEPROM pin 13 is connected with a power supply of
micro computer.
14 DO O data out Data output
15 DGND digital ground Ground of digital block
16 NC non connection Not used
17 VDD_3.3 power supply The power supply for digital block. 3.3V ± 0.2V
18 RDS_CK O RDS clock Output of RDS clock(2.5V)
19 RDS_DATA O RDS data Output of RDS data(2.5V)
E 20 RDS_LOCK O RDS lock Output unit “High” active(2.5V) (RDS_LOCK turns over by the
external transistor. “Low” active)
21 RDS_HSLK O RDS high speed Output unit “High” active(2.5V)(RDS_HSLK turns over by the
lock external transistor. “Low” active)
22 AUDIOGND audio ground Ground of audio block
23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output
24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output

DEH-2800MP/XN/EW
72
1 2 3 4
5 6 7 8
7.2.2 DISPLAY

- LCD(CAW1900)(DEH-2800MP/XN/EW, DEH-2820MP/XN/EW) A

E
SEGMENT

COMMON

DEH-2800MP/XN/EW
5 6 7 8
73
1 2 3 4

- LCD(CAW1903)(DEH-2800MPB/XN/EW)
A

E
SEGMENT

COMMON

DEH-2800MP/XN/EW
74
1 2 3 4
5 6 7 8

- LCD(CAW1901)(DEH-281MP/XN/EW)
A

E
SEGMENT

COMMON

DEH-2800MP/XN/EW
5 6 7 8
75
1 2 3 4

7.3 OPERATIONAL FLOW CHART

Power ON

AREF1, VDD, AVDD, AVREF1=5 V


Pin 7, 68, 74, 75

B bsens
Pin 64

bsens=L

asens
Pin 63

asens=L

C
Starts communication with Grille microcomputer.
300 ms

swvdd←L
Pin 21
300 ms
In case of the above signal, the communication
Source keys with Grille microcomputer may fail.
operative If the time interval is not 300 msec, the oscillator
D may be defective.

Source ON

SYSPW←H
Pin 43

Completes power-on operation.(After that, proceed to each source operation.)

DEH-2800MP/XN/EW
76
1 2 3 4
5 6 7 8

8. OPERATIONS

DEH-2800MP/XN/EW
5 6 7 8
77
1 2 3 4

About the fixing screws for the front panel


A If you do not operate the Detaching and Replacing
the Front Panel Function, use the supplied fixing
screws and fix the front panel to this unit.

Fixing screw
(CBA1994)

Fixing screw
(CBA1994)
B

DEH-2800MP/XN/EW
78
1 2 3 4
5 6 7 8

DEH-2800MP/XN/EW
5 6 7 8
79
1 2 3 4

- Jigs List
Name Jig No. Remarks
A Test Disc TCD-782 Checking
g the g
grating
g
L.P.F. Checking
g the g
grating
g ((Two pieces))

- Grease List
Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
B Grease GEM1045 CD Mechanism Module

Before shipping out the product, be sure to clean the


following portions by using the prescribed cleaning
tools:
C
Portions to be cleaned Cleaning
g tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning
g paper
p p : GED-008

DEH-2800MP/XN/EW
80
1 2 3 4

Anda mungkin juga menyukai