Miscellaneous
T.V. Stand - Cabinet Mount
Design Reg. No:162020/90
Special Features
! Pull out and swivel will now be available in plate widths
of 356 mm, 406 mm, 457 mm, and 508 mm.
! Ribbed for strength with elegant looks.
! Ball cage construction for safety and strength.
! Extension : 360 mm.
! Rotation angle 360 °.
Specifications
Code Nos.
Plate Size Extension Rotation Circle of
Finish
With Without (mm) mm Angle Rotation
Sliding Sliding
356X305
TVS 35 TVR 35 (14”X12”) 469
406X305
TVS 40 TVR 40 (16”X12”) 508
Powder
360 360º coated-
brown
457X305
TVS 45 TVR 45 (18”X12”) 550
508X305
TVS 50 TVR 50 (20”X12”) 593
Caution
Do not install on a light cabinet or trolley which may topple forward.
202
Fitting Instructions
1. The depth of cabinet should be based on the depth of the T.V. and no 4. In case the top plate has to be opened, kindly study the centre
less than 16"(400 mm). The minimum width between side walls of Pivot-Bush assembly. (Refer fig. 2).
cabinet should be more than circle of rotation (Refer fig. 1). 5. Fix side supports using M6 Screws and Nuts provided. Tighten all
2. Ebco TV Stand is supplied in assembled condition and can be installed Nuts and Screws firmly to prevent damage of over turning while
in assembled condition. operating T.V Stand (Refer fig.3).
3. The maximum permissable load is 48 kgs.
Ø6.4
Heavy duty slide
400mm
50
Ø2
8 Nos. M6
mounting screws.
Fig. 3 ASSEMBLY
203
Wall Mount T.V. Stand
Special Features
! Ideal for living rooms, kitchens, offices, hotels, hospitals, airports and restaurants.
Available in three plate sizes (406,457 and 508mm)
4
10
!
! Has up to 20 º angle adjustment and 240º rotation.
68
! Nylon safety belts to strap T.V.
! Easy to install.
! Load capacity of 60 Kgs
62.5 62.5
Specifications
TVWSA 40 406
TVWSA 45 457
TVWSA 50 508
546
Fitting Instructions
20º
165
20º
Special Features
! Aesthetically designed.
! Ideal to store away.
! All steel construction for strength.
! 180° rotation is possible for left and right arrangement.
Specifications Fig.1
Fitting Instructions
1. Fix the assembly on the wall by using screws and wall plugs provided.
Use only Ø9.5mm (3/8") masonary drill. (Ref. Fig.1)
2. Rotate the board to required position and tighten the knob properly. (Ref. Fig.2)
3. Before unfolding the Ironing board pull the support leg out and lock with the pin
as given in diagrams. While storing remove the pin and push the leg to inside. Fig.2 Knob
Support leg
Lock Pin
3 Pullout the Support leg & and insert 5 Loosen the Knob & turn the board
the Lock pin into the hole to lock it. to required position & tighten the
2 Pull board to horizontal position knob properly
Caution
The wall which the Ironing Board is attached must be of solid wood, brick work or concrete only.
205
Presto-Deluxe Ironing Board
206
PRESTO - Dual Ironing Board + Ladder
Special Features
As Ironing Board
! Metallic cotton cover with 7 mm foam underlay.
! Large mesh ironing surface of 330 mm wide and 1000 mm length.
! Anti rust iron rest tray conveniently positioned at the side of the
ironing board to keep the hot iron safely.
! Fixed height of 850 mm.
! Heat resistant silicone pads to keep iron on.
! Sturdy frames to sustain tolerable weight.
! Can be folded after use and stored away conveniently. As Ironing Board
As Ladder
! The unit is easily convertible to a three step ladder.
! The three step has the height of 710 mm.
! Highly efficient anti-skid mat on the each step.
Specifications :
Item Code No.
Mini
207
Pro - Lift
Special Features 4
! Easy to open
15
! Safety in use
Damped Closing Ø20 .
17
!
.D
! Easy to fit P.C
Long Life
27
!
17
Ø4
Specifications
PLC 06 60 N
PLC 08 80 N
PLC 10 100 N
PLC 12 120 N
PLC 15 150 N
Caution
PLC 20 200 N 1. High pressure.
2. Do not dismantle or damage.
PLC 25 250 N 3. Do not expose to heat or fire.
ASSEMBLE ROUND BALL OF BRACKETS BY PUSHING INTO PLASTIC SOCKETS AT EACH END
DISASSEMBLE BRACKETS FROM PLASTIC SOCKET BY USING SCREW DRIVER TO LIFT STEEL CLAMPS
250±2EXTENDED LENGTH.
LIFT STEEL CLAMP FOR DISASSEMBLY 80±2STROKE LENGTH.
LIFT STEEL CLAMP FOR DISASSEMBLY
BALL BALL
PLASTIC SOCKET PLASTIC SOCKET
208
FOR OVERLAY SHUTTERS
22+T
80
80
º
TO BE USED WITH EBCO SLIP ON
OVERLAY HINGE (HS-1)
27
10 10
25 25
FRONT VIEW OF CABINET
IN CLOSED CONDITION SIDE VIEW OF CABINET WITH
WITH DRILLING DIMENSIONS SHUTTER IN OPEN CONDITION SIDE VIEW OF CABINET
FOR SHUTTER TO DETERMINE HEIGHTS TO FIT CLOSED CONDITION
TO FIT OVAL MOUNTING BRACKET ROUND MOUNTING BRACKET WITH DRILLING DIMENSIONS
ADDING THICKNESS OF SIDE WALL AFTER DETERMINING OPENING FOR CABINET TO FIT
OF CABINET (T) TO DIMENSION 22 ANGLE OF SHUTTER ROUND MOUNTING BRACKET
22 80
80
º
TO BE USED WITH EBCO SLIP ON
T
10+T
10+T 25+T
25+T
SIDE VIEW OF CABINET WITH
FRONT VIEW OF CABINET SHUTTER IN OPEN CONDITION SIDE VIEW OF CABINET
IN CLOSED CONDITION TO DETERMINE HEIGHTS TO FIT IN CLOSED CONDITION
WITH DRILLING DIMENSIONS ROUND MOUNTING BRACKET WITH DRILLING DIMENSIONS
FOR SHUTTER ADDING THICKNESS OF SHUTTER (T) FOR CABINET TO FIT
TO FIT OVAL MOUNTING BRACKET TO DIMENSION 10 & 25 ROUND MOUNTING BRACKET
209
Pro - Lift Bed Fittings
Special Features
! Ideal for storage under bed .
! Special gas spring available in two loads.
! 30° opening angle allows easy access.
! Easy to fit and operate.
Specifications
Max. Weight Recommended
Code No. Type Bed Size (feet)
(Kgs.) Width Length
3 to 4
PLBF 75 Medium 75.0 6 to
Feet
61/2
4 to 5 Feet
PLBF 120 Heavy 120.0
Feet
Fitting Instructions
1. Fit the Fix Brackets on bed frame as per given dimensions. (Ref. Fig.1).
without the gas spring fitted
2. Now fix the bed platform to the top brackets. (Ref. Fig.2).
50.0
100.0
3. Lastly fit the gas spring as shown in the diagram (Ref. Fig.3). Ø5.
2
20.0
98.0 400.0
Special Note :
Installation dimensions are only recommendation and will vary depending on Side View
type of construction design.
Fig.1
Fig.2 Fig.3
210
Table Bracket
Design Reg. No Pending
Special Features
! Ideal fitting for a fold away table.
! Special release latch helps fold the table
400
! Built for strength and durability.
! Available in silver and black powder coated.
400
Specifications
TB 40 100 kgs.
Pull the
Fitting Instructions latch to
fold the
1. Screw the Side Bracket to the wall with wall plugs and Bracket
screws. (Ref. Fig. 1). The wall must be of solid wood, brick
wood or concrete only. Do not use plywood, blockboard etc.
2. It can be folded and kept while not in use. Pull the slider as Fig. 2 Fig. 2A
given in the diagram to fold the bracket. (Ref Fig. 2 & 2A)
Special Features
! Ideal for storing appliances like microwave ovens 340.0
in kitchen. Can also be used for DVD players etc.
! Built for strength and durability.
500.0
Specifications
Fig. 2
Fitting Instructions
1. Fix the brackets on the wall by using wall plugs and screws provided (Ref. Fig. 1). The wall onto which the fix bracket is
attached must be of solid wood, brick work or concrete only. Do not use on plywood, blockboard, etc
2. Length adjustment is possible of 160mm (Ref. Fig. 2.)
3. If it is not in use, can be folded to avoid the inconvenience (Ref. Fig. 3)
Fig. 3
211
Cupboard Pull-out
Cabinet Roof
Special Features
±3.0
! For tall unit storage cupboards.
! Consists of base unit having special plastic
WOOD SCREWS
25.4
coated bearings for silient running.
8 NOS.
! Top guide has lateral adjustments.
! Base unit has angle adjustments. TOP ASSEMBLY
FRONT VIEW
! Used where narrow spaces are available and
gives easy access from both sides.
! Ideal for kitchen larders, office storage units and Pull out Cupboard
all types of tall unit pull cupboards. M6x40 CSK. BOLT
4 NOS.
! Load capacity: 170 Kgs.
Specifications
84.0
Fitting Instructions
Caution
1. Avoid the disassembly of the unit. PULLOUT CUPBOARD FLOOR
(Fig. 4)
BASE UNIT
FRONT
96.0
96.0
FRONT
35.0 432.0 441.0
45.0 16.5
40.0
FRONT
80.0
FRONT
TOP TRACK
27.5 34.0
TOP GUIDE
Tongue Handle
Special Features
! Easy to fit.
! System-32 compatible.
! Designed for inset drawers.
! Available in 2 Sizes. .0
32
Specifications
‘A’ ‘B’
Code No. Finish Fig. 1
in mm in mm
Fitting Instructions
1. Make slots in front facia of drawer as shown in diagram.
(Ref. Fig. 1). For overlay drawers make extra slot vertically
inside face of front facia for avoid the gap while closing.
2. Screw the Tongue handle to the front facia. (Ref. Fig. 2) Fig.2
213
Sofa cum Bed Fittings (click)
Design Reg. 194231
Special Features
! This latest design new model is sturdy and easy to operate with a
simple clicking mechanism for positive locking in sitting position.
Fitting Instructions
SEAT BRACKET BACK REST
1. Bring Sofa cum Bed fittings into Bed Position (Ref. Fig. 2) BRACKET
Fig. 2
BED POSITION
1830 CENTRE OF
mm (6
f t.) BOTTOM FRAME
SEAT
BACK REST
BOTTOM
FRAME 60
600.0
450.0 450.0
214
PUSH SEAT FURTHER TILL
CLICKING SOUND IS HEARD
BACK REST
DROPS BACK TO DROP THE SEAT BACK TO
HORIZONTAL POSITION HORIZONTAL POSITION
LIFT SEAT
1 2 3 4
1 2 3
Glass Handle
Caution
Do not use packings on inside of glass. Use only on outside.
215
Cabinet Shelf Support
Specifications 10.0
Ø5.0
Code Nos. Model Used for Size Finish Min.
6.0mm
CSS 1 1 lug Glass Shelves Small Ø5.0 Deep Ø5.0
Chrome Min. Min.
CSS 2 2 lugs Wooden Shelves Regular Plated 9.0mm 9.0mm
Deep Deep
Drilling diagram Drilling diagram
Special Features
! Simple, cost effective and easy to fit. Forged steel core for strength.
! Available with a soft clear sleeve for glass and a white sleeve for wood board shelves.
Specifications
Ø5.0
Code Nos. Suitable for Min. 9.0 mm
Deep
PSS 1 Glass Shelf
Special Features
! Die cast with elegant, attractive design with soft pad for glass.
! Fits in a Ø5 mm hole.
! Nickel plated for good looks.
Ø5.0
(Min. deep
Specifications 9.0mm)
Furn Felt
Special Features
! Manufactured out of compressed felt.
! Protects floors from scratches.
! Acts as an easy glide
! Reduces noise.
! Can be used with chairs, sofas, tables, etc.
With
Specifications Pin
217
Bumpers
Special Features
! Non-Staining & Non-Marring
! Easy ‘Peel Off’ Application
! Superior Abrasion Resistance BS-1
! Superb Resistance to Skidding &
High Coefficient of Friction
! Crack-Resistance & Resilient
! Vibration & Shock Dampening
! UL Recognized Component
BS-5
Specifications
Code Nos. Type Diameter Height Width Per Pad Per Carton
Physical Properties
Standard Product Softer Durometre
BS-20
Durometre, Shore A 60 to 70 50 to 55
Tensile Strength, psi (g/cm2 ) 627 (44, 082) 750 (52, 730)
Tear Strength, pli (g/cm) 214 (38, 216) 127 (22, 680)
Bashore Rebound, % 27 35
BS-33
Abrasion Resistance, g/1000 0.016 0.010
cycles Tabor H18, 1kg
BS-32
218
Lined and Dimpled sheet
Special Features
! Made from the finest quality E.V.A. Plastic sheets.
! Easy to clean.
! Can be used in cupboards, drawers and baskets.
! Available in dimpled or lined.
! Reduces metal to metal contact.
! Eliminates noise.
219
Sliding Folding Fittings
23.0
! Shutter number can be increased in multiples of two
i.e. 2, 4, 6, etc for larger areas.
! Weight of each shutter should not exceed 25 kgs.
Max. 6.0
Min. 3.0
Specifications
Fitting Instructions
1. One set is for two folding shutters.
2. Set of two sliding fittings with four wheels each are fitted on
top track.(Refer fig.1).
Max. 12.0
3. Set of two sliding fittings with one wheel each are fitted on
Min. 4.0
bottom track.(Refer fig.2).
12.0
75.0
50.0 to ble
Prefera
13
.0
15.0
33.0
3.0
35.0
30.0
35.0
Fig.3 CAVITY FOR SLIDING FITTINGS Fig.4 FOLDING HINGE Fig.5 END STRAPS
220
Shutter Lift
Special Features
! Ideal for overhead storage.
! Convenient to remove stored articles.
! Easy to fit and adjust for different width.
! Max. shutter load - 15 Kgs.
Specifications
Code No. SL 24 32
128.0 74.0
Fitting Instructions
1. Screw the Lifting Mechanism to the side of the
10.0
(Ref. Fig.4)
5. Internal Cabinet dimensions:
Width - Min. 564, Max. 764
Height - Min. 320, Max. 450
9.5
Shutter Adj.
Screws
Fig.4 Fig.3
221
Plinth Screws
Plinth Fittings
Code Nos.
Minimum With Without Range
shut height Screw Screw Skirting (mm) Skirting clip & Bracket
(mm) clip
37.5
222
Sliding Cabinet Shutter Fittings
! Ideal for sliding cabinet shutters. ! Eccentric arrangement for gap setting.
! Special rollers for smooth silent running. ! PVC rail also available.
! Anodised Aluminium rails for long life.
Specifications
BOTTOM HOUSING
Shutter Distance 'A'
Thickness ‘mm'
10
13.0
0 .0
16 mm 21.0 Min. 75.
0 . 0 to rable
5 efe
19 mm 24.0 Min. Pr
Fitting Instructions
30.5
7.5
1. Use Ø35mm cutter to make cavities on the inside 5.0
Ø3 8.0
of shutter. (Refer Fig.1)
13.0
CABINET
2. Cavity should be 10mm deep.
3. Fit top housing and bottom housing in top and
6.0
10
4. Rail is fitted in a slot at top and bottom of cabinet. .0
Groove should be 8mm wide and 6mm deep.
5.0
(Refer Fig.2) Ø3
Fig.1
5. Wheel of bottom housing should sit in bottom rail. SHUTTER
6. Spring loaded guide in top housing is pulled down
so as to engage in top rail there by retaining the
shutter. (Refer Fig.3) SPRING LOADED
GUIDE
6.0
CABINET
8.0
223
Cupboard Latch
Design Reg. Nos: 56st: 166020/93;
56cr: 166803/94;
150st: 166933/94
Special Features
! Spring loaded for safety and smooth operations.
! Cranked bolt with plate for internal fitting with external shutter.
! Straight bolt with clip for external fitting with flush shutter.
Also, straight bolt with plate for internal fitting with recessed shutter.
11.5
3.0 12.0
Model A B C
B C
BC
Straight Bolt 56 mm 3.0 8.0
56.0
Cranked Bolt 56 mm 13.0 8.0
Cranked Bolt 96 mm 96.0 13.0 10.0
A
224
Gallery Fittings
Special Features
! To be used for filing cabinets with 'ebco' full panel drawer slides.
! Supplied in standard size of 500mm rods for depth and 400mm
rods for width of drawer.
! Rods must be cut to size to adjust for final depth and width of
required drawer.
Specifications
Fig.1
Code No. GF 1
GALLERY FITTINGS
Fitting Instructions
1. Use 'ebco' Full Panel drawer slides for best results (Refer fig.1 & 2)
2. Fit end brackets onto front facia and rear panel to fit rods (Refer fig.3)
3. Cut the 500 mm rods to required size after measuring gap between front CABINET
and back screws.
4. Put the 400mm cross rods into plastic -Connector after measuring the Fixed slide
required width and cutting to size. (Refer fig. 4). 2 mm
Full Panel
5. Slide the cross rods with T-Connectors to adjust for size of file pockets. Slide
Fig.2
T-CONNECTOR
15.5mm
225
Modular Gallery Fittings
For Kitchen
For Office
Specifications
Partition Bracket
Assembly
Top Connector
Top Connector
Rail
(without perforation)
Base
226
Cabinet Stay
Design Reg. No: 191525/03
! This new Cabinet Stay has a built-in braking arm. Cabinet Stay
! To be used in cabinets having upward opening shutters.
! Recommended to use with Slip on/ Click on Hinges (overlay) .
! Fittings can be varied for different opening angles.
! System 32 compatible.
! Manufactured out of die-cast zinc and chrome plated.
Specifications
Code No. CS 1*
Fitting Instructions
70.0 32.0
DING
N PEN
DESIG
REG.
REG. DESI
GN PENDING
32.0
37.0
Fig. 1 OPEN CONDITION Fig. 2 CLOSED CONDITION
Caution
Max. opening angle do not exceed more than 105°
227
Flap Stay
Design Reg. No: 164046/92
Special Features
Specifications
Internal B
Code Model Cabinet Height at which
A Finish
Nos. (length) Height the stay
(mm) has to be used
Fitting Instructions
1. Flap Stays for wall units, bar cabinets etc., with FLAP OPEN FLAP CLOSED
horizontal opening flaps. SIDE PANEL 35 UPPER SHELF
2. Flap Stays keep flaps open in the horizontal position so
that they can be used as a shelf with a load bearing Adjustable brake
capacity of 12 kgs.
3. Flap Stays come in pairs and are left and right handed.
4. The Stays have an adjustable brake, used for
compensating the weight of different sizes of flaps to
prevent banging. A
X
5. Flap Stays come in 3 sizes of different lengths, Regular,
Large and Extra Large for cabinets with different Length
internal heights as shown in the table. Max. Load 12kg.
6. Flap Stays are easy to fit. To ensure smooth working
they must be used along with Plano hinges. Can also B
be used with regular hinges.
LOWER SHELF
10 C
228
Spring Clip
Design Reg. No: 164045/92
Special Features
! Easy to install with self adjustment.
16.0
20.0
! Special austempering heat treatment to ensure long life.
Model Cabinet Cupboard
22.0
Hole size 2.5 mm 3.0 mm
25.0
Load 1.75 kgs 3.5 kgs
Finish White, Zinc Plated, Powder Coated - Brown Spring Clip Big (SC2)
Hanger
HGR 6 60
HGR 8 80
HGR 10 100
Hanger Plate
229
Wall Plug
Fitting Instructions
1. Drill a hole of 55mm deep in the wall. Use Ø9.5mm (3/8") masonry drill only.
2. Insert the wall plug into the hole. Wall plug should enter fully into the hole.
Shelf Support
Design Reg. No: 158990/87
Special Features
10.0
! Manufactured out of plastic. 12.0mm Deep
! This stiffner gives an Min.
additional support to the
6mm bottom of a drawer at
the centre of the facia.
! It requires a Ø10mm hole.
Specifications
230
Adjustable Corner Bracket
Fitting Instructions
1. Cabinet can be fitted directly on to an Anchor Bolt or on a Wall
Plate as shown in fig. 1 Fitted with Anchor Bolt
Caution
1. Strictly follow the fitting instructions and ensure that all screws
are fully tightened. Fig.1
12 mm stment
ju
8.0
on tal Ad
Horiz
18.0
41.0
33.5
29.0
Vertical Adjustment
11 mm
16.0
12.5
Fig.2 Fig.3
231
Corner Bracket / Bottom Corner Bracket
Special Features
! All steel construction.
! Ribs provided for increased strength.
! Screws provided for angle and height adjustment.
! Maximum Load capacity: 120Kgs
Specifications
CONNECTOR (L & R)
Fitted behind wall cabinet
Item Code Nos. Fig.1 in the top corners.
Fitting Instructions
22.0
Top Corner Bracket
1. Fit Left & Right connectors behind wall cabinet in the top
corners (Refer fig. 1)
BRACKETS (4 nos.)
2. Fit Brackets on the wall as per desired height (Refer fig.2) Fig.2
Fitted onto wall.
3. Hook cabinet onto the bracket (Refer fig.3)
4. Cabinet can be adjusted if crooked with height adjustment.
(Refer fig.4)
Fig.3
HEIGHT
ADJUSTMENT
Fig.4 Fig.5
232
Bed Clamp
Special Features
! Manufactured out of steel for strength
! Clips easily in to each other forming a strong joint
! Require four joints to form a bed frame
Specifications
Code No. BC 4
Corner Clamp
Special Features
! Ideal for joining three sides of cabinet giving right angle joints
Specifications
CC 38 38 x 38 x 38
PVC Sealer
! Ergonomically designed for good grip. Code Nos. Distance ‘A’ Finish
! Available in different finishes.
! Required routing. SH 1819-5 160
End Cap
SH 1819-7 224
19.0 44.0
SH 1819-9 288 Silver
&
SH 1819-14 448 Champagne
Fitting Instructions
EC 1819 End Cap 1819
‘A’
1. Use 19mm board.
SH 1819 2 mtrs
2. Routing required (Ref. Fig1)
Fig.1
Special Features
! Designed especially for Ebco prolift.
To be used with Aluminium Profile
Glass Shutter Fittings.
! Strong design helps upward opening
shutter.
Fig.1
Specifications
Code No. GSP-BP Fig.2
Fitting Instructions
1. Refer diagrams in Aluminium Profile Glass Shutter & Pro-Lift pages to
get the fitting diagrams and dimensions.
2. Insert the bracket in to the aluminium track and tighten the grub screws
properly (Ref. Fig. 1.)
3. Clip the bracket to the Pro-lift and tighten the hinge screws which are
fitted on the top of the cabinet. (Ref. Fig. 2.)
234
Shutter Handle Square - Aluminium 3012
End Cap
'B'
'A'
( Ref. Fig. 1 ) SH 3012-14 SQ 448 458
2. End Brackets have M4 tapping with
center to center distances compatible EC 3012 S End Cap 3012 Square
with system-32
SH 3012 Shutter Handle Profile 2 mtrs
Fig.1
SH 3012-3 96 104
End Cap
SH 3012-5 160 168
30.0 12.0
SH 3012-7 224 232
Silver
SH 3012-9 288 296 &
Champagne
SH 3012-14 448 456
‘B’ ‘A’
EC 3012 R End Cap 3012 Round
Shutter Handle
SH 3012 2 mtrs
Profile Fig.1
235
Shutter Handle Profile - Aluminium 1935
Special Features
! Ergonomically designed for good grip.
! Available in different finishes.
! Available in different lengths.
! Compatible for 18 mm board.
Specifications
19.0
35.0
9.0
From front face
12 mm
2.5
Special Features
! Ergonomically designed for a good
37.0
Specifications
2.5
Code No. SH 1937
236
Aluminum Edge Profile
Special Features
! Ergonomically designed to protect the
edges of the shutter.
! Ultra modern looks and finish
Specifications
1.5
18.5
1.0
18.5
9.0
Special Features
! Ideal to be used where ventilation is required
like kitchen shutters (cabinets and drawers)
especially for gas cylinders, wardrobes, etc.
Specifications
Size in mm Slot size in
Code No.
(W x L) shutter (W x L)
237
Aluminium Handles
Handle - “S”
Special Features
! Variety of designs to select from.
! Ergonomically designed for good grip..
! Available in different lengths as per system - 32.
! Surface finish - Silver Sand.
Handle - “I”
Specifications
JAH - 160
IAH - 32
IAH - 64 Model Code No.
IAH - 96 KAH - 32 Handle - “K”
Aluminium Handle -I
IAH - 96 SF KAH - 64
IAH - 160 Aluminium Handle K KAH - 96
IAH - 224 KAH - 160
KAH - 224
GAH - 32
Handle - Rail
GAH - 64
Model Code No.
GAH - 96
Aluminium Handle -G SAH - 160
GAH - 160 Aluminium Handle -S
SAH - 256
GAH - 224
GAH - 288
Handle - "J"
238
Aluminium Profile Glass Shutter
Special Features
! Designed for Aluminium profile (Code: GSP-A) overlay glass shutters.
! Max. opening angle 105°
! Max. Shutter size is 34"x22"(850mmx550mm)
! Max. glass thickness is 5 mm.
! Also available in half overlay (10mm crank) hinge.
Specifications
Item Code No.
Shutter Type Distance 'A'
Aluminium Profile for Shutter Frame GSP-A
With Overlay Hinge 34.0
P.V.C. Profile for Shutter Frame GSP-P1
With Half Overlay Hinge 39.0
P.V.C Profile for 4mm / 5mm Glass GSP-P2
Fitting Instructions
1. Cut the Aluminium profile to suitable length and the both
ends should be cut in 45° to form a Mitre joint.(Ref. Fig.1)
2. Fit the Mounting plate of Hinge to the cabinet as per given Fig. 1
dimensions. (Ref.Fig.2)
3. Insert the Hinges in the track and tight the grub screws
properly. (Ref. Fig.3)
4. Insert the P.V.C profiles on the edges of the glass and
slide it into the track as shown in diagram (Ref. Fig.4)
5. Insert the glass shutter in the track and join the Aluminium
profiles with Comer Brackets. (Ref. Fig.5) and place the
cover on it and tighten the screw properly.(Ref. Fig.6) 'A'
6. Engage the P.V.C. profile for shutter frame in the groove
provided in the aluminium profile as shown and press the
side to lock in the other groove. (Ref. fig. 7A & 7B) Cut the
P.V.C. profile to required length except the space where
32.0
239
Fig. 3 Fig. 4
Fig. 5 Fig. 6
Groove
Press to Lock
Overlay Hinge
Shutter
Shutter
Cabinet Cabinet
Closed Condition Open Condition
Shutter
Cabinet Cabinet
Closed Condition Open Condition
240
Aluminum Profile Glass Shutter (I)
Special Features
! Designed for Aluminium profile overlay glass shutters.
! Max. opening angle 105°
! Max. Shutter size is 34"x22"(850mmx550mm)
! Max. glass thickness is 5 mm.
! Also available in half overlay (10mm crank) hinge.
Specifications
Hinge with Lock Bracket for Alu. Shutter-Half Overlay GSPI - HI2
Fitting Instructions
1. Cut the Aluminium profile to suitable length and the both ends should be
cut in 45° to form a Mitre joint. (Ref. Fig 1)
2. Fit the Mounting plate of Hinge to the cabinet as per given dimensions.
(Ref.Fig.2)
3. Insert the Hinges in the track and tight the screws properly. (Ref. Fig.3)
4. Insert the P.V.C. profiles on the edges of the glass and slide it into the
track as shown in diagram. (Ref. Fig.4) 45
°
5. Insert the glass shutter in the track and join the Aluminium profiles with
Corner Brackets. (Ref. Fig.5)
6. Place the cover on the Aluminium profile and press to lock as shown
diagram. (Ref. Fig. 6) Cut the cover to suit the length aluminium profile
and make the slots where hinges are fitted.
7. Screw the hinge to the Mounting plate. By loosening the bracket screws,
the shutter can slide horizontally and also be pivoted for varying pressure.
Fig.1
241
36.0
32.0
Fig.3
Fig.2 CABINET
Fig.4 Fig.5
PRESS
Fig.6 Fig.7
Overlay Hinge
Shutter
Shutter
Cabinet Cabinet
Closed Condition Open Condition
Half Overlay Hinge
Shutter
Shutter
Cabinet Cabinet
Closed Condition Open Condition
242
Display shelving system
Design Reg. 190913/Jan 03; 190914/Jan 03;
190996/Jan 03;
Special Features
• Elegantly designed to suit different needs.
! Available in a variety of models and sizes.
! It is ideal if you have different items to display from time to time.
! Specially designed to impart maximum strength and to eliminate play.
! A unique stabilizer screw and nut holds the shelf in place.
! Available with an elegant Aluminium Track for light loads and a Steel
Track for high loads.
! Available for glass, wood shelves and hanger systems.
Fitting Instructions
1. Screw the Track on the wall as shown in
diagram. (Ref. Fig.1)
2. Hook the Brackets and Holders in to the slots
provided on the Track as given in diagram. (Ref.
Fig.2)
3. Refer the diagram for assembly of stabilizer nut.
(Ref. Fig.3)
243
Specifications
Item Code No. Size mm Finish
244
Adjustable Glass Shelf Support
Special Features
! Elegantly designed to suit Modern & Traditional decor.
! Adjustable for glass shelves of thickness
! Screw locking with plastic pad for protection.
! Finish - Gold & Satin Nickel Plating, as well as Powder Coating.
Specifications
Code No. Finish
Fitting Instructions
1. Only suitable for solid walls.
2. Span between supports should not exceed 400 mm. (Ref. Fig.1)
3. Shelf should not overhang by more than 100 mm. (Ref. Fig.1)
4. Uniform distributed load not to exceed 15 Kgs. (Ref. Fig.1)
5. Loosen the scew below the shelf support. (Ref. Fig.2)
6. Fix it on the wall with screws and wall plugs provided. (Ref. Fig.3)
7. Place the glass and tighten the screws properly. (Ref. Fig.4)
15 kgs.Max.
U.D. Load
245
Wall Shelf Rod
Special Features
! Special wall mounting shelf rods .
! Rods are completely concealed after fitting.
! Rods are made of steel & hardened for strength.
! Easy to fit.
Specifications
Support Thread Max. Cantilever
Load (2 Pieces)
Code No. Length Length over hang of shelf
Kgs. U.D.L.
A A mm
Fitting Instructions
1. Fit special wall plug provided in the dry wall using Ø9.5 (3/8")
masonary drill. (Ref. Fig. 1).
2. Maintain center to center pitch between rods and drill Ø9.0 mm holes
in the shelf (Ref. Fig. 2)
3. Insert shelf onto rods.
4. Two rods can take a load of 15 kgs. including weight of shelf.
5 For heavier loads increase the no. of rods proportionately.
Ø9.5 (3/8")
55 mm deep min.
Dry Wall
B
Shelf
A ter d
c en tane
o in
r t ma
e nte be
C to
ch
pit
Fig. 1 Fig. 2
246
Euro Quick - Manual / Pneumatic
Special Features
! These drilling machines can be used to drill all kinds of hinge holes in cabinets and doors.
! It is simple & safe to operate & very efficient.
Specifications
Model EQM 1 EQP 1
Drilling Procedure
Manual
1) Placing and positioning of board is done manually on the bed.
2) The motor drives the drills through a gear box directly, and the drill block moves up and
down manually by the plunger handle.
Pneumatic
1) Placing and positioning of board is done manually on the bed.
2) The “Clamp” switch is turned on and the pneumatic camps, camp the board in position.
3) When the “Start” button is pressed, the motor drives the drills directly through a gear box,
and the drill block moves down by a pneumatic cylinder automatically. When start button is
released the drill block will automatically move up.
Model EQP 1- Pneumatic Machine
4) Release the “Clamp” switch to deactivate the pneumatic clamps.
.0
Ø8
.0
Ø8
Ø35.0
45.0
32.0
Leading
Edge of
Cabinet Edge of
Cabinet 9.5 Shutter
Shutter
247
Hinge Multi Boring Jig (System 32)
Special Features
! Manufactured to very high tolerances for use on
CNC multi boring machines .
! Highly accurate, fast and cost effective for fitting ebco hinges.
! Bores three holes at a time using left hand & right hand carbide
cutters.
! Has a built in dummy rotating spindle at 64 mm to prevent jig
from rotating.
! Two or more jigs can be used in a CNC machine to drill holes 64.0
for two or more hinges in shutter, wardrobe doors etc at a time.
Ø10
Specifications
Code No. JH35 M32
45.0
9.5
Ø35.0
12.0 deep
Drilling Diagram
248
Jig for Hinge
Special Features
6MM SOCKET
WITH SPRING LOADED
! Can be used with any drilling machine having 3- jaw chuck.
PLUNGERS
! Three carbide cutters provided to bore Ø35 and Ø8 mm holes. TO DRIVE CUTTER
! Carbide cutters provide long life. AND BORE HOLES
! Depth of cutters can be adjusted and locked.
! Clamp can be adjusted to lock different thickness of board.
SCREW ADJUSTMENT THREADING
! Special allen key provided to drive 6mm sockets with drilling m/c. FOR THICKNESS FOR SETTING DEPTH
! Center of holes to aligned with slot before clamping. OF THE BOARD FOR CUTTER
Specifications
Code No. JH 35
250