FRAMING
HALFEN FRAMING SYSTEMS
Product range - Overview
Framing Channels, Bolts
data force Compr. member data force Compr. member data force Compr. member
y z y z y z
3 F F F
y FQ y y
x z x z x z
FZ FZ FQ FZ FQ
4
page 64 - 65 pages 66 - 69 pages 70 - 73
Cantilevers
pages 74 - 77
Pipe Clamps, Pipe Supports
Company:
Name: Tel.:
Fax:
channels
Notes, Work aid
and Washer
hex head bolt
Channel nut and HALFEN-DEHA Vertriebsgesellschaft mbH
Fixing parts Liebigstr. 14
and
40764 Langenfeld
KON Tel. 02173/970-0
cantilever arm Fax. Tel. 02173/970-123
HCS - AS HCS - R
7
reinforcement
Construction account:
VA composite
anchor (pin)
2
HALFEN FRAMING SYSTEMS
Index
Accessories
Clamps, beam clamps 47 - 49 2
Ductwork supports and accessories 50 - 51
Design Properties
Materials, design types / finishes of HALFEN Channels and T-head bolts 52 - 53
Section properties of HALFEN Framing channels (plain back and slotted); other data 54 - 59 3
Loading capacity of HALFEN Channels as compression members 59
Loading capacity data for HALFEN T-head bolts 60 - 61
Support Structures
HALFEN POWERCLICK Framing System 63; System 52 (heavy duty) 62 - 65
System 41 and 22 (medium duty), Standard systems 66 - 69 4
System 36 (light duty) 70 - 71
System 28 (light duty) 72 - 73
Cantilevers
5
Pipe Clamps, Pipe Supports
3
HALFEN FRAMING SYSTEMS
Channel Fixing (Introduction)
1
• Non-slip bolting at any point with Halfen T-head bolts.
• Corrosion protection remains intact after bolting.
• Can be adjusted or extended on site without any need for machining (it is
therefore not restricted by different hole settings when changes are made to
components).
Accessories
all in one.
3
Support Structures
e.g. M 12
7 e = 30 mm
4
HALFEN FRAMING SYSTEMS
Steel Support Structures (Introduction)
1
• Efficient and economical production of mo-
dular system support structures, made-to-
measure and supplied with all the necessary
bolts and fittings.
Accessories
(reducing time needed for planning and ob-
serving production tolerances). 2
• Low-cost fully adjustable standard products
height adjustable
which can replace a whole range of expensi-
ve structural parts. Special designs are possi-
ble for all structural parts depending on the
quantities involved.
Design Properties
Any component can be
laterally replaced at any time without
adjustable any fuss
3
Support Structures
4
Cantilevers
Using HALFEN Support structures 5
uneconomic procedures are avoided such
as:
Requ. position
Actual position
- complex design work on constructions
Pipe Clamps, Pipe Supports
components.
5
HALFEN FRAMING CHANNELS AND ACCESSORIES
Heavy Duty Framing Channels
FL
3 up to 7,5 kN
FQ
High load distribution, shear force FQ
Support Structures
up to 9 kN
up to 9 kN, tensile force FZ up to 31 kN
and force in longitudinal direction FL up
4 to 7,5 kN.
Material/construction:
/48
72
HM
/34
52
Notes, Work aid
HM
/30 HM
50 Co
HM 2 nc
7 40/2 HTA ret
HM e
/23
® pages 8 - 16 38
M
HZ /20
29 HM = surface
M
HZ mounted,
HTA = cast in
6
HALFEN FRAMING CHANNELS AND ACCESSORIES
Heavy Duty Framing Channels
Accessories
2
High degree of safety:
HSR - HALFEN T-head bolts are nibbed
and and therefore non-slip. Up to 7,5 kN
(with safety factor n = 3) per bolt when
Design Properties
used in mild steel channels (material
quality fv = hot-dip galvanised and wb =
mill finish). 3
Corrosion protection provided by galva-
nising remains fully intact even after
assembly.
Support Structures
There is a large selection of Stainless steel
HS HALFEN T-head bolts and GWP lo-
cking plates (from M 8 up to M 20, de- 4
pending on section) for all Stainless steel
channels.
Cantilevers
5
Twist protection
Selection of HALFEN T-head bolts and locking plates due to the hook-head shape of the
profile lips in conjunction with the
Pipe Clamps, Pipe Supports
7
® pages 9 - 19 ® pages 9 - 19
HALFEN locking plates allow the use of
any kind of bolts.
7
HALFEN FRAMING CHANNELS
Channel 72/48
HM 72/48
Framing Channels, Bolts
hot rolled
72
1
4,5
48,5
Accessories
2
15,5
33
Design Properties
3
bolt length l [mm]
Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
rial, dard weight section inertia modulus point at span L
finish = loading
y z y z F
max F
Support Structures
Nominal HM 72/48
y
Back-to-back x z FQ
channels FZ
to order pages 54 - 55 page 58 page 59
6
Bolt-accessories
VUS 72/49
Washers for direct assembly
Notes, Work aid
7 VUS 72/49
page 45
Subject to alterations
8
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channel 72/48
M 20 M 24 M 27 M 30 M 24
HS 72/48
Accessories
Order example: HS 72/48 - M 24 x 100 - fv
l
lrequ. Calculation of 2
bolt length l requ.
Material/finish Halfen T-head bolts (® S. 53): i t mv
for Halfen T-head bolts:
fv = h.d. galvanised, strength grade 4.6
gv = electroplated, strength grade 4.6 Halfen
t-head bolt lrequ. = required bolt length
gv 8.8 = electroplated, strength grade 8.8 i = profile lip
fv 8.8 = h.d. galvanised, strength grade 8.8 m = nut ldeduct.
Design Properties
A4-50 = Stainless steel grade A4-50 v = spare ~5 mm
t = clamping thickness
(t £ lrequired - ldeduction) 3
M 20 GWP 72/48 gv A4
HSR 72/48 Length l a b d
Length l Mat.
Locking plates
Halfen T-head bolt [mm] Thread Thread [mm] [mm] [mm]
with nibs
75 75 fv 8.8 M 12 M 12 62 31 22
incl. nut b
Support Structures
Order example: a M 16 M 16 62 31 22
HSR 72/48 - M 20x75 - fv 8.8 M 20 M 20
d
62 31 22
58
Order example:
GWP 72/48 - M 20 - gv
4
M 12 9,3
M 16 17,3
l
M 20 22,0
Cantilevers
FS
5
Pipe Clamps, Pipe Supports
9
HALFEN FRAMING CHANNELS
Channel 52/34
HM 52/34 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
hot rolled rial, dard weight section inertia modulus point at span L
finish = loading
y z y z F
max F
52,5
1 for Stock To y y
L L [m]
explan. no. order x z x z
see p. = max F
G A Iy Iz Wy Wz À 0,50 1,00 1,50
52 0280. . .
3,5
fv 190-00003 4,96 6,32 9,42 24,13 5,49 9,19 17,0 21,0 8,7 4,4 2,2
Accessories
A4 190-00001
2
11,5
22
Nominal dimensions
[mm]
Design Properties
load member
HM
y z
F
4 Back-to-back
y FQ
channels D x z
4 FZ
to order
52/3
HM pages 54 - 55 page 58 page 59
Channel-accessories
Cantilevers
10
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channel 52/34
Accessories
l
50 fv
55 55 gv 55 A4-50 2
55 fv
60 60 gv 60 gv 60 gv8.8 60 A4-50
60 gv8.8 60 gv8.8
65 65 gv
75 75 gv 75 A4-50
Design Properties
80 80 gv 80 gv 80 gv8.8 80 A4-50
80 gv8.8 80 gv8.8 80Li A4-50
100 100 gv 100 gv 100 gv 100 A4-50 100 A4-50 3
100 gv8.8 100 gv8.8
100 fv 100 fv
125 125 gv 125 gv 125 gv 125 A4-50
150 150 gv 150 gv 150 gv 150 A4-50 150 A4-50
150 fv 150 gv8.8
Support Structures
200 200 gv 200 gv 200 gv
300 300 gv 300 gv
Order example: HS 50/30 - M 16 × 50 - gv Calculation of bolt length l requ. ® p. 9
4
M16 M20 gv A4
HSR 50/30 Length l GWP 50/30 a b d
Halfen T-head bolt [mm] Length l Mat. Length l Mat. Locking plates Thread Thread [mm] [mm] [mm]
with nibs
40 40 fv 8.8 b M 8 M 8 43,5 21 12
incl. nut a
41 45 45 gv 8.8 M 10 M 10 43,5 21 12
d
Cantilevers
75 75 gv 8.8 M 16 M 16 43,5 21 12
Order example:GWP 50/30 - M 12 - gv
perm. load Thread loading capacity [kN]
5
Material / finish Halfen T-head bolts (® p. 53):
l
FS M 16 9,3
A4-50 = Stainless steel grade A4-50
Halfen for mild steel channels for stainless steel channels
T-head Max. pull out Max. longitudinal load per Halfen T-head bolt Max. pull out Max. longitudinal load
per T-head bolt per T-head bolt per Halfen T-head bolt
bolts - 6
load
capa-
cities À
FL FL
FS FS FL
Type HS, grade 4.6 Type HSR, grade 8.8
Grade Grade tightening tightening Grade Grade tightening
Notes, Work aid
11
HALFEN FRAMING CHANNELS
Channels 50/30 and 49/30
HM 50/30 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
hot rolled rial, dard weight section inertia modulus point at span L
finish = loading
y z y z F
max F
49
1 for Stock To y y L [m]
x z x z L
explan. no. order
see p. = max F
G A Iy Iz Wy Wz À 0,50 1,00 1,50
52 0280. . . [kg/m] [cm²] [cm4] [cm4] [cm³] [cm³] [kN] £ L [cm] F [kN]
2,75 HM 50/30
30
wb 200-00002
fv 200-00003 3,23 4,11 5,23 14,15 3,35 5,78 11,0 19,0 5,4 2,7 1,2
Accessories
A4 200-00001
8
2 HM 49/30
22 wb 220-00001
fv 220-00002 3,07 3,91 4,32 13,92 2,44 5,57 4,9 46 4,5 2,3 1,0
Nominal dimensions A2 220-00003
[mm]
A4 220-00004
Length: 6070 mm Order example: HM 50/30 - fv - 6070 or Stock no. 0280.200-00003
Design Properties
load member
HM
y z
F
4 Back-to-back
y FQ
channels
/30D x z
FZ
to order 50
HM pages 54 - 55 page 58 page 59
HM 49/30 Á
cold rolled Channel-accessories
Cantilevers
5 50 SDM 41/8 PA - 41
Sound attenuator Channel closer strip
3,25
Pipe Clamps, Pipe Supports
30
page 50 page 46
6
7,5
22
Bolt-accessories
VUS 52/34 SIC 50/30
Nominal dimensions Washer for direct assembly Lock washers
[mm]
Notes, Work aid
page 45 page 45
Subject to alterations
12
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channels 50/30 (hot rolled) and 49/30 (cold rolled)
Accessories
l
50 fv
55 55 gv 55 A4-50 2
55 fv
60 60 gv 60 gv 60 gv8.8 60 A4-50
60 gv8.8 60 gv8.8
65 65 gv
75 75 gv 75 A4-50
Design Properties
80 80 gv 80 gv 80 gv8.8 80 A4-50
80 gv8.8 80 gv8.8 80Li A4-50
100 100 gv 100 gv 100 gv 100 A4-50 100 A4-50 3
100 gv8.8 100 gv8.8
100 fv 100 fv
125 125 gv 125 gv 125 gv 125 A4-50
150 150 gv 150 gv 150 gv 150 A4-50 150 A4-50
150 fv 150 gv8.8
Support Structures
200 200 gv 200 gv 200 gv
300 300 gv 300 gv
High corrosion resistant Stainless steel T-head bolts Order example: HS 50/30 - M 16 × 50 - gv
Á HS 50/30, material order code HCR, on request. Calculation of bolt length l requ.® p. 9 4
M16 M20 gv A4
HSR 50/30 Length l GWP 50/30 a b d
Halfen T-head bolt Length l Mat. Length l Mat. Locking plates Thread Thread [mm] [mm] [mm]
[mm]
with nibs
incl. nut 40 40 fv 8.8 b M 8 M 8 43,5 21 12
a
45 45 gv 8.8 M 10 M 10 43,5 21 12
d
Cantilevers
75 75 gv 8.8 M 16 M 16 43,5 21 12
Order example:GWP 50/30 - M 12 - gv
perm. load Thread loading capacity [kN]
5
Material / finish Halfen T-head bolts (® p. 53):
fv = h.d. galvanised, strength grade 4.6 M 8 4,0
gv = electroplated, strength grade 4.6 M 10 6,4
l
FS M 16 9,3
A4-50 = Stainless steel grade A4-50
Halfen for mild steel channels for stainless steel channels
T-head Max. pull out Max. longitudinal load per Halfen T-head bolt Max. pull out Max. longitudinal load
per T-head bolt per T-head bolt per Halfen T-head bolt
bolts - 6
load
capa-
cities À
FL FL
FS FS FL
Type HS, grade 4.6 Type HSR, grade 8.8
Grade Grade tightening tightening Grade Grade tightening
Notes, Work aid
13
HALFEN FRAMING CHANNELS
Channels 40/22, 40/25 and 422
HM 40/22 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
hot rolled rial, dard weight section inertia modulus point at span L
finish = loading
39,5 F
y z y z
max F
1 for Stock To y y
L L [m]
explan. no. order x z x z
2,25 18 see p. = max F
G A Iy Iz Wy Wz À 0,50 1,00 1,50
52
23
wb 210-00002
fv 210-00003 2,12 2,70 2,02 5,85 1,65 2,96 5,7 21,0 2,7 1,1 0,5
Accessories
Nominal dimensions
[mm] A4 210-00001
2 HM 40/25
wb 230-00001
fv 230-00002 2,08 2,66 2,01 6,06 1,36 3,03 3,8 33,0 2,5 1,0 0,4
A2 230-00003
/22 A4 230-00004
40
HM Length: 6070 mm Order example: HM 40/22 - fv - 6070 or Stock no. 0280.210-00003
Design Properties
À see note  on p. 55
/2 2D
Back-to-back Channel-accessories
channels
40 Other channel data, design properties
3 HM Max. tensile / Max. load Sound attenuator
to order Channel
transverse compression
data SDM 36/6
load member
HM 40/25 y z
cold rolled F
40
y FQ
x z
FZ
Support Structures
VUS 40/25
Cantilevers
SIC 40/22
5
5 40/2
HM page 45 page 45
HM 422 (C 40) The cold rolled profile HM 422 is intended to be used for pre-dominantly static loads. For
dynamic load the profile HM 40/22 is to be used.
Pipe Clamps, Pipe Supports
cold rolled
39,5
Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
rial, dard weight section inertia modulus point at span L
6 finish = loading
y z y z F
21,5
2 18 max F
Nominal dimensions
[mm] HM 422
wb 110-00001 1,55 1,98 1,27 4,29 1,04 2,17 2,5 36,0 1,8 0,8 0,3
7 fv 110-00002
Length: 6000 mm Order example: HM 422 - fv - 6000 or Stock no. 0280.110-00002
2
42 À see note  on p. 55
HM
Subject to alterations Further design properties: pages 54 - 59; Channel accessories: same as HM 40/22 (see above)
14
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channels 40/22 and 422
HS 40/22 Length l M 10 M 12 M 16 M 10 M 12 M 16
Accessories
l
Design Properties
300 300 gv
Order code: HS 40/22 - M 12 x 50 - gv
Calculation of 3
bolt length lrequ.
® p. 9
Support Structures
with nibs 40 40 gv 8.8 M 6 35 17 10
incl. nut b a
60 60 gv 8.8 M 8 M 8 35 17 10
4
d
Order code: M 10 M 10 35 17 10
32,
5 HSR 40/22 - M 16 x 60 - gv 8.8 M 12 M 12 35 17 11,5
Order code: GWP 40/22 - M 10 - gv
Material/finish Halfen T-head bolts (® p. 53): perm. load Thread loading capacity [kN]
fv = h.d. galvanised, strength grade 4.6 M 6 2,2
gv = electroplated, strength grade 4.6 M 8 4,0
l
Cantilevers
M 10 6,4
A4-50 = Stainless steel grade A4-50 FS M 12 9,3 5
Pipe Clamps, Pipe Supports
À Note: Do not exceed channel load capacity! See also p. 54 - 59 (design properties). = Standard = To order
15
HALFEN FRAMING CHANNELS
Channels HZM 38/23 and 29/20
HZM 38/23 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
toothed, hot rolled rial, dard weight section inertia modulus point at span L
finish = loading
! F
NEW 38
y z y z
max F
1 for Stock To y y
L L [m]
explan. no. order x z x z
see p. = max F
G A Iy Iz Wy Wz À 0,50 1,00 1,50
52 0284. . . 4 4
[kg/m] [cm²] [cm ] [cm ] [cm³] [cm³] [kN] £L[cm] F [kN]
23
HZM 38/23
wb 060-00001
2,42 3,09 2,11 6,17 1,59 3,25 12,0 20 4,1 1,4 0,6
5
fv 060-00003
Accessories
A4 060-00002
18
2 Length: 6070 mm Order example: HZM 38/23 - fv - 6070 or Stock no. 0284.060-00003
À see note  on p. 55
Nominal dimensions
Other channel data, design properties Channel-accessories
[mm] Max. tensile /
Channel
transverse
Max. longitud. Toothing SDM 36/6
data tensile load Sound attenuator
load
Design Properties
y z 3 mm
3
3 38/2 y FL
M x FQ
HZ z
FZ
pages 54 - 55 page 58 page 58 page 50
Support Structures
HZM 29/20 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
toothed, hot rolled rial, dard weight section inertia modulus point at span L
finish = loading
! F
NEW 29 y z y z
max F
Cantilevers
wb 050-00001
1,51 1,98 1,02 2,42 0,91 1,67 8,0 15 2,3 0,6 0,3
Pipe Clamps, Pipe Supports
14 fv 050-00003
Length: 6070 mm Order example: HZM 29/20 - fv - 6070 or Stock no. 0284.050-00003
À see note  on p. 55
Nominal dimensions
[mm] Other channel data, design properties
6
Max. tensile /
Channel Max. longitud. Toothing
transverse
data tensile load
load
y z 3 mm
y FL
/20 x z
FQ
29
Notes, Work aid
FZ
HZM
pages 54 - 55 page 58 page 58
7
Subject to alterations
16
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channels HZM 38/23 and 29/20
Toothed bolts incl. nut Hammer-head bolts incl. nut position marking
1 notch
l
l
l
l
= Typ HS,
smooth
HZS 38/23 HZS 29/20 HS 38/17 À HS 38/23 HS 28/15 HS 29/20
M 12 M 16 M 12 M 10 M 12 M 16 M6 M8 M 10 M 12
FYQ Fx FQ
Y Fx FYQ Fx FYQ FYQ FYQ FYQ FYQ FYQ FYQ FYQ Fx FQ
Y
Length l
Accessories
Fz Fz Fz Fz Fz Fz Fz Fz Fz Fz Fz Fz
[mm] Material Material Material Material Material Material Material Material Material Material
load ranges
30 gv8.8 gv8.8 gv8.8 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 2
40 gv8.8 gv8.8 gv8.8 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6
approved for
50 gv8.8 gv8.8 gv8.8 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6
dynamic loads
60 gv8.8 gv8.8 / A4 H gv8.8 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6
80 gv8.8 gv8.8 / A4 H gv8.8 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6
100 gv8.8 gv8.8 gv8.8 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6
Design Properties
125 gv8.8 gv8.8 gv8.8 gv4.6 gv4.6 gv4.6 gv4.6
150 gv8.8 gv8.8 gv8.8 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6 gv4.6
200 gv8.8 gv8.8 gv4.6 gv4.6 3
250 gv8.8
300 gv8.8 gv8.8
Note: gv8.8 resp. gv4.6 = galvanic special coating for particularly long-lasting corrosion protection, allowed to Calculation of
make up for hot-dip galvanised (cp. approval. DIBt Z-21.4-1691 Halfen Channels, Att. 7 Tab. 11); grade 8.8 resp. bolt length l requ.
4.6. H: also available in stainless steel A4-70 ® p. 9
Support Structures
Locking plates GWP
for Channel 38/23 GWP 38/17 for Channel 29/20 GWP 28/15 4
b a b a
® page 35 o. 37 ® page 39 o. 41
d
d
Perm. load capacities for Halfen T-head bolts, requ. tightening torque, perm. bending moment
À fits to Channel 38/23
Halfen T-head bolts: HZS, grade 8.8 HS, grade 4.6 Ã
Á fits to Channel 29/20
tighte- Perm. F Perm. bending tighte- Perm. tensile/ Perm. bending requ.
Cantilevers
 Refered to leading edge of channel resp. concrete. In
ning in all moment ning transverse moment hole
case of bending with additional tensile load, calculate
torque directions per bolt
Â
torque load per bolt
Â
adjacent
element with superposition:
5
F Q
Y Fx F Q
Y
Fz Fz perm. F = perm. tensile force
Thread [Nm] [kN] [Nm] [Nm] [kN] [Nm] [mm] perm. M = perm. bending moment
F £ perm.F · (1 - M/perm.M) F = existing tensile force
M6 3 2,2 2,0 7 M = existing bending moment
M8 8 4,0 5,0 9
Pipe Clamps, Pipe Supports
7
VUS 40/25 SIC 38/23 US DIN 9021 SIC 29/20
17
HALFEN FRAMING CHANNELS
Channels 50/40 and 486
HM bzw. HL 50/40 Cold rolled profiles are intended to be used for pre-dominantly static loads. For
Framing Channels, Bolts
cold rolled dynamic load hot-rolled profiles (pages 8 - 16) are to be used.
49
1 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
rial, dard weight section inertia modulus point at span L
finish = loading
y z y z F
max F
see p. =
52 G A Iy Iz Wy Wz À 0,50 1,00 1,50
Accessories
fv 090-00003
22 A4 090-00001
HL 50/40 0281. . .
Nominal dimensions wb 100-00001
3,15 3,73 7,14 15,36 3,65 6,27 5,4 53,0 5,8 2,9 1,7
[mm] fv 100-00002
Design Properties
A4 100-00003
Length: 6000 mm Order example: HM 50/40 - A4 - 6000 or Stock no. 0281.090-00001
3 À see note  on p. 55
18
/4 0 Other channel data, design properties Channel-accessories
50
HM Max. tensile / Max. load SDM 41/8 PA 41 HPE 50/40
Channel transverse compression Sound Channel Channel
Support Structures
Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
5 HM 486 rial, dard weight section inertia modulus point at span L
cold rolled finish = loading
48 y z y z F
max F
see p. = max F
52 G A Iy Iz Wy Wz À 0,50 1,00 1,50
2,5 4 4
[kg/m] [cm²] [cm ] [cm ] [cm³] [cm³] [kN] £L[cm] F [kN]
27
HM 468 0280. . .
6 wb 100-00001 2,31 2,95 2,97 9,62 1,92 4,01 3,5 47,0 3,3 1,6 0,7
6
fv 100-00002
18
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channels 50/40 and 486
M 10 M 12 M 16 M 20 M 12 M 16 M 20
HS 50/30
Accessories
l
55 fv
60 60 gv 60 gv 60 A4-50 2
65 65 gv
Li = left hand thread 75 75 gv 75 A4-50
80 80 gv 80 gv 80 A4-50
80Li A4-50
100 100 gv 100 gv 100 gv 100 A4-50 100 A4-50
Design Properties
100 fv 100 fv
125 125 gv 125 gv 125 fv 125 A4-50
150 150 gv 150 gv 150 gv 150 A4-50 150 A4-50 3
150 fv
200 200 gv 200 gv 200 gv
300 300 gv 300 gv
Order code: HS 50/30 - M 16 x 50 - gv Calculation of
Material / finish Halfen T-head bolts (® p. 53)
bolt length l requ.
Support Structures
gv = electroplated, str. gr. 4.6 ® p. 9
fv = h.d. galvanised, str. gr. 4.6
A4-50 = Stainless steel A4-50
GWP 50/40
gv A4 loading capacity 4
Locking plates Thread Thread
Bolt-accessories
Thread [kN]
VUS 52/34 SIC 50/30
20 42 M 6 M 6 2,2 Washer for direct assembly Lock washers
M 8 M 8 M 8 4,0
8
M 10 M 10 M 10 6,4
M 12 M 12 FS M 12 6,4
M 16 M 16 M 16 6,4
Cantilevers
GWP 50/30 Thread Thread a x b x d [mm] Thread [kN] VUS
Locking plates 52/34 SIC 50/30 5
M 8 M 8 43,5 x 21 x 12 M 8 4,0
b a M 10 M 10 43,5 x 21 x 12 M 10 6,4
d
M 12 M 12 43,5 x 21 x 12 M 12 9,3
page 45 page 45
M 16 M 16 43,5 x 21 x 12 M 16 9,3
Order code: GWP 50/40 - M 12 - gv
Pipe Clamps, Pipe Supports
19
HALFEN FRAMING CHANNELS
Channel 63/63
28
Accessories
63
2 0
25
3
63/6
HZL
2,5 toothing
Design Properties
3 9,5 22 9,5
Product data
Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
rial, dard weight section inertia modulus point at span L Other channel data, design properties
finish = loading
y y F Max. load
z z
Cantilevers
- toothed, slotted
6,35 7,09 33,07 42,95 10,06 13,63 5,6 134 16,2 8,3 5,5 pages 56 - 57 page 59
fv Á 030-00001
fv  030-00003
6
À see note  on p.
55 Channel accessories Locking plates, Halfen T-head bolts
Á Length: 3000 mm SDM 41/8 PA 41 HPE 63/63 HZS 41/22
 Length: 6000 mm GWP 41/22
Sound attenuator Channel closer strip Channel end cap
Order example:
HZL 63/63 - fv - 3000 FS
Notes, Work aid
or Stock no.
0283.030-00001
7
FL
HA
LF
EN
page 50 page 46 page 46 page 31
Subject to alterations
20
HALFEN FRAMING SYSTEM ACCESSORIES
for Channel 63/63
1
N
5k
Channel
41/41
N
5k
N
5k
Locking plate
with "bite" Channel
41/22
Accessories
2
POWERCLICK HALFEN POWERCLICK
bolt set ONE COMBINED SYSTEM for economical supports
pre-assembled
in all fittings - Heavy duty support system 63/63
- Medium duty support system 41/41 ® pages 66 - 69
Design Properties
- Light duty support system 41/22
3
Support Structures
4
All locking
plates and bolts
of System 41 fit
to System 63 as
well
® page 31
Cantilevers
N
5k 5
Pipe Clamps, Pipe Supports
GWP 41/41
6
GWP 41/41SN
HZS 41/41
Notes, Work aid
21
HALFEN FRAMING CHANNELS AND ACCESSORIES
Medium Duty Framing Systems
(Selection)
With its numerous connecting parts
and identical-format channels this
1 system is especially suitable for
• complete assemblies
(® HALFEN POWERCLICK Framing
System)
• low cost in-house stock-keeping
/22
41
Accessories
D
/22
41
Design Properties
Locking plate
GWP 41/41
3
1
1/4 • Locking plate with 'bite'. The
Support Structures
l4
ne
h an flamehardened teeth bite into the
c
se
Ba channel lips.
4 • High longitudinal loading capacity.
• Corrosion protection remains intact
even after assembly.
• Suitable for all bolts with metric
standard thread.
Cantilevers
,
/62
41 3
/ 8
41
Pipe Clamps, Pipe Supports
ms
ste
Sy
ng
7 /63 Fra
mi
L 63 ty Locking plates with springs or
HZ y Du
av HALFEN Bolts are best suited for all
He
® 20
p. fixing situations, especially for larger
structures.
22
HALFEN FRAMING CHANNELS AND ACCESSORIES
Medium Duty Framing Systems
sv = pre-galvanised
zinc coating > 20 μm,
A4 = A4 stainless steel
Accessories
(Material data ® p. 52)
2
Associated framing systems:
- HALFEN Fittings ® p. 67
- HALFEN POWERCLICK
Framing System 41
(Techn. catalogue
Design Properties
HALFEN POWERCLICK
Framing System, ® Notes p. 66) 3
To make fitting easier the
locking plates and HALFEN - HALFEN Cantilevers ® p. 76
T-head bolts should be
pre-mounted
on the fittings to be attached.
Support Structures
Locking plate
Type GWP 41/41 4
® p. 31
Cantilevers
5
Hexagon head screw
HSK - M 12
® p. 44
Pipe Clamps, Pipe Supports
6
Toothed channels provide
shock-resistant fixing for
non-slip connections and
higher safety requirements.
Notes, Work aid
23
HALFEN FRAMING CHANNELS
Channel 41/41
HM resp. HL 41/41 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
HM 41/41 0280. . .
wb 080-00001
sv 080-00002 2,61 3,33 7,16 9,22 3,06 4,46 5,6 49,0 5,4 2,7 1,7
Accessories
fv 080-00003
2 A4 080-00004
7
HL 41/41 0281. . .
22 wb 010-00001
sv 010-00003 2,46 2,98 6,07 9,16 2,84 4,43 5,6 42,0 4,7 2,3 1,5
Nominal dimensions
fv 010-00002
[mm]
A4 010-00004
Design Properties
HM41/41D 0280. . .
wb 150-00001
5,33 6,67 35,81 18,44 8,67 8,93 5,6 132,0 14,9 7,4 4,9
3 fv 150-00003
14 A4 150-00002
4
1
4 1/4
HL
5 1D Channel
Max. tensile / Max. load
/4 transverse compression
41 data
load member
HM
y z
F
y
Pipe Clamps, Pipe Supports
x z
FZ FQ
Base channel for System 41 Series pages 54 - 57 page 58 page 59
6 HALFEN 41 Series
Cantilevers:
® page 76 Locking plates, Halfen T-head bolts Channel-accessories
GWP 41/41 SDM 41/8 PA 41 HPE 41/41
HZS 41/41 Sound Channel Channel
attenuator closer end cap
strip
Notes, Work aid
FS
7
HALFEN System HALFEN 41 Series FL
41 Series: Fittings: page 31 page 50 page 46 page 46
® page 66 - 69 ® page 67
24
HALFEN FRAMING CHANNELS
Channel 41/22
HM resp. HL 41/22 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
for Stock To y y
1
L L [m]
2,5 explan. no. order x z x z
21
see p. = max F
52 G A Iy Iz Wy Wz À 0,50 1,00 1,50
[kg/m] [cm²] [cm4] [cm4] [cm³] [cm³] [kN] £L[cm] F [kN]
7
HM 41/22 0280. . .
22 wb 120-00001
sv 120-00002 1,80 2,30 1,19 5,32 0,97 2,58 5,6 15,0 1,8 0,6 0,2
Nominal dimensions
Accessories
[mm] fv 120-00003
A4 120-00004 2
HL 41/22 0281. . .
wb 020-00001
sv 020-00003 1,57 1,95 0,99 5,27 0,89 2,55 5,6 12,0 1,5 0,5 0,2
fv 020-00002
A4 020-00004
14
Design Properties
HM41/22D 0280. . .
/22 wb 160-00001
41 3,60 4,59 5,55 10,64 2,69 5,15 5,6 42,0 4,7 2,3 1,3
HM fv 160-00002 3
A4 160-00003
28
Length: 6000 mm Order example: HL 41/22 - fv - 6000 or Stock no. 0281.020-00002
50 À see note  on p. 55
2
4 1/2
HL Note:
Support Structures
Toothed profile 41/22
® page 27
D
/22
41
HM
Cantilevers
Channel
Max. tensile /
transverse
5
data load
y z
y
Pipe Clamps, Pipe Supports
x z
FZ FQ
pages 54 - 57 page 58
6
Locking plates, Halfen T-head bolts Channel-accessories
GWP 41/41 and 41/22 SDM 41/8 PA 41 HPE 41/22
HZS 41/41 and 41/22 Sound Channel Channel
attenuator closer end cap
strip
Notes, Work aid
FS
7
FL
page 31 page 50 page 46 page 46
Subject to alterations
25
HALFEN FRAMING CHANNELS
Channel 41/41, toothed
HZM resp. HZL 41/41 toothed Due to positive locking the profile is especially suited when increased loading capacities in
Framing Channels, Bolts
Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
rial, dard weight section inertia modulus point at span L
1 finish = loading
y z y z F
max F
see p. = max F
G A Iy Iz Wy Wz À 0,50 1,00 1,50
52
4 4
[kg/m] [cm²] [cm ] [cm ] [cm³] [cm³] [kN] £L[cm] F [kN]
HZM 41/41 0284. . .
Accessories
wb 010-00001
2 2,63 3,25 6,91 9,10 2,91 4,41 5,6 47,0 5,3 2,6 1,6
7
fv 010-00002
A4 010-00003
22
HZL 41/41 0283-. .
Nominal dimensions wb 010-00001
[mm] fv 010-00002 2,46 2,90 5,87 9,04 2,69 4,38 5,6 41,0 4,6 2,3 1,4
A4 010-00003
Design Properties
HZM41/41D 0284. . .
wb 030-00001
3 fv 030-00002
5,11 6,51 33,74 18,38 8,16 8,90 5,6 126,0 13,8 7,0 4,7
A4 030-00003
14
/41
Length: 6000 mm Order example: HZM 41/41 - A4 - 6000 or Stock no. 0284.010-00003
41 À see note  on p. 55
HZM
28
Support Structures
50
4
1
4 1/4
HZL
x z
Base channel for System 41 Series, FZ FQ
toothed pages 54 - 57 page 58 page 59
HALFEN POWERCLICK
6 Framing System 41:
® page 66 - 69
Locking plates, Halfen T-head bolts Channel-accessories
GWP 41/41 and 41/22 SDM 41/8 PA 41 HPE 41/41
HZS 41/41 and 41/22 Sound Channel Channel
attenuator closer end cap
strip
Notes, Work aid
FS
7
HALFEN 41 Series FL
Fittings: page 31 page 50 page 46 page 46
® page 67
26
HALFEN FRAMING CHANNELS
Channel 41/22, toothed
HZM resp. HZL 41/22, toothed Due to positive locking the profile is especially suited when increased loading capacities in
for Stock To y y
L L [m]
x x
7
Accessories
Nominal dimensions wb 020-00001
[mm] fv 020-00002
1,79 2,22 1,16 5,21 0,92 2,52 5,6 14,0 1,7 0,6 0,2 2
A4 020-00003
HZL 41/22 0283. . .
wb 020-00001
fv 020-00002 1,57 1,87 0,97 5,15 0,86 2,49 5,6 12,0 1,5 0,5 0,2
14
A4 020-00003
Design Properties
2
41/2 HZM41/22D 0284. . .
M wb 040-00001
HZ
fv 040-00002
3,58 4,66 5,64 11,00 2,68 5,33 5,6 42,0 4,6 2,3 1,3 3
28 A4 040-00003
50 Length: Order example: HZM 41/22 - A4 - 6070 or Stock no. 0284.020-00003
2
1/2 • HZM 41/22: 6070 mm À see note  on p. 55
L4 • HZL 41/22: 6000 mm
HZ • HZM 41/22D: 6070 mm
Support Structures
4
/22D
41
HZM
Cantilevers
Channel Max. tensile /
transverse
5
data
load
y z
y
Pipe Clamps, Pipe Supports
x z
FZ FQ
pages 54 - 57 page 58
6
Locking plates, Halfen T-head bolts Channel-accessories
GWP 41/41 and 41/22 SDM 41/8 PA 41 HPE 41/22
HZS 41/41 and 41/22 Sound Channel Channel
attenuator closer end cap
strip
Notes, Work aid
FS
7
FL
page 31 page 50 page 46 page 46
Subject to alterations
27
HALFEN FRAMING CHANNELS
Channel 41/62
HM resp. HL 41/62 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
62
fv 140-00003
2 HL 41/62 0281. . .
wb 040-00001
3,14 3,99 17,27 13,03 5,47 6,31 5,6 81,0 4,5 2,2 1,0
sv 040-00003
fv 040-00002
HM 41/62 D 0280. . .
wb 170-00001 6,84 8,72 108,11 26,21 17,45 12,69 5,6 269,0 15,1 7,5 5,0
7
Design Properties
fv 170-00002
22 Length: 6000 mm Order example: HM 41/62 - fv - 6000 or Stock no. 0280.140-00003
3
Nominal dimensions
À see note  on p. 55
[mm] Á Possible bulging, tilting and buckling must be prevented by appropriate measurements.
Support Structures
4
14
/62
41
HM
28 Locking plates, Halfen T-head bolts
Cantilevers
50
GWP 41/41
5 HZS 41/41
2 FS
4 1/6
HL
Pipe Clamps, Pipe Supports
FL
page 31
6
Other channel data, design properties Channel-accessories
SDM 41/8 PA 41
Channel Sound Channel closer strip
data attenuator
D
/62
Notes, Work aid
41 y z
HM
7 x
y
z
pages 54 - 57
page 50 page 46
Subject to alterations
28
HALFEN FRAMING CHANNELS
Channel 41/83
HM resp. HL 41/83 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Accessories
fv 130-00003
HL 41/83 0281. . . 2
83
wb 030-00001
sv 030-00003 3,93 5,02 37,07 16,93 8,85 8,20 5,6 133,0 7,5 3,7 2,2
fv 030-00002
Length: 6000 mm Order example: HM 41/83 - fv - 6000 or Stock no. 0280.130-00003
Design Properties
À see note  on p. 55
Á Possible bulging, tilting and buckling must be prevented by appropriate measure.
3
7
22
Support Structures
Nominal dimensions
[mm]
4
Cantilevers
GWP 41/41
HZS 41/41 5
14
/83 FS
41
HM
Pipe Clamps, Pipe Supports
28
50 FL
page 31
6
Other channel data, design properties Channel-accessories
SDM 41/8 PA 41
1 /83 Channel Sound Channel
HL4 data attenuator closer
strip
Notes, Work aid
y z
x
y 7
z
pages 54 - 57
page 50 page 46
Subject to alterations
29
HALFEN FRAMING CHANNELS
Channels HLL 41/41 and 41/22
HLL 41/41 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
Length: 6000 mm Order example: HLL 41/41 - sv - 6000 or Stock no. 0282.010-00002
À see note  on p. 55
2
7
22
Locking plates, Halfen T-head bolts Channel-accessories
Nominal dimensions
[mm] GWP 41/41 SDM 41/8 PA 41 HPE 41/41
14 HZS 41/41 Sound Channel Channel
Design Properties
4
HLL 41/22
Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
rial, dard weight section inertia modulus point at span L
41 finish = loading
y z y z F
max F
for Stock To y y
Cantilevers
L L [m]
explan. no. order x z x z
1,5
5 max F
21
see p. =
52 G A Iy Iz Wy Wz À 0,50 1,00 1,50
4 4
[kg/m] [cm²] [cm ] [cm ] [cm³] [cm³] [kN] £L[cm] F [kN]
7
Nominal dimensions Length: 6000 mm Order example: HLL 41/22 - sv - 6000 or Stock no. 0282.010-00003
[mm] À see note  on p. 55
14
6
2
41/2
H LL Locking plates, Halfen T-head bolts Channel-accessories
28
GWP 41/41 SDM 41/8 PA 41 HPE 41/22
50
HZS 41/41 Sound Channel Channel
attenuator closer end cap
strip
Notes, Work aid
FS
7
FL
page 31 page 50 page 46 page 46
Subject to alterations
30
HALFEN T-HEAD BOLTS AND LOCKING PLATES
for Channels 41/22 to 41/83
3 4,
7,5
(Note: l
Type HS 41/41 Type HS 41/41
d d d l
without toothing without toothing
34, 34, ® p. 47)
5 5 b ® S. 47)
b
gv A4 gv gv Zinc flake plated d/b gv A4 fv 8.8 A4
Thread Thread Thread Thread Thr. × l [mm] Thr. × l [mm] [mm] Thread Thread Thr. × l [mm] Thr. × l [mm]
Accessories
M 6 M 6 M 6 M 6 M 6 × 30 6 / 20 M 6 M 12 x 35 M 12 x 35
M 8 M 8Ã M 8 M 8 M 8 × 30 M 8 × 50 8 / 20 M 8 M 8 M 12 x 50 M 12 x 50
M10×50/M10x75 9 / 20 M 10
2
M 10 M 10 M 10 M 10 M10 × 30 M 10 M 12 x 80
F M 12 * F M 12 F M 12 M12 × 30 M12 × 50 9 / 20 M 12 M 12 M 16 x 35
M12 × 75 M12 × 100 * 9 / 20 M 16 x 50 M 16 x 50
M 12 À M 12 11 / 20 M16 x100
M 16 ÀÁ M 16 ÀÁ M16 × 63 ÀÁ 12 / 30 M 16 M 16
Calculation of
Design perperties
bolt length lrequ.
Perm. load capacities of Locking plates and Halfen T-head bolts System 41 Series ® p. 9
for mild steel channels Max. pull out Max. longitudinal load per Halfen T-head bolt resp. locking plate 3
per Halfen T-head bolt Types GWP 41/41 (not for thread M16) and HZS 41/41
Material: gv, fv Note:
Do not
exceed
HZS HZS channel
41/41 41/22 load capa- FL
GWP GWP FS city!
Support Structures
41/41 41/22
for all channels 41 a. 63 Series for Channels for Channels for Channels
at at
Locking plates Halfen T-head bolts HM/HL HZM / HZL HLL
tightening tightening
GWP GWP HZS HZS 41/22, 41/41, 41/22, 41/41, torque 41/22, 41/41 torque 4
41/41 41/22 41/41 41/22 41/62, 41/83 63/63
Thread -SH, -SN [kN] Æ [kN] Å [kN] [Nm] Â [kN] Å [Nm] Â
M 6 – 5,0 1,0 2,2 12 1,0 12
M 8 – 6,0 2,4 4,0 28 2,4 28
M 10 – 7,0 3,5 5,0 55 3,5 55
M 12 À 9,0 À 5,0 À 5,0 À 75 3,6 À 55
F M 12 7,0 4,0 5,0 60 (50) 3,6 55 (50)
Cantilevers
M 16 Á À Æ 12,0 (7,0) À 7,5 À 7,5 À 125 (80) 4,5 À 95 (80)
5
for Stainless Steel Channels Max. pull out Max. longitudinal load per Halfen T-head bolt
per Halfen T-head bolt
Material: Stainless Steel A4
Pipe Clamps, Pipe Supports
HZS
FL FL
41/22
GWP GWP FS
41/41 41/22
Note:
Do not exceed channel
for Channels 41 at tightening for Channels 41 at tightening 6
Locking plates Halfen T-head bolts torque torque
load capacity!
GWP GWP HZS HM/HL HZM/HZL
Thread 41/41 41/22 41/22 [kN] Æ [kN] [Nm] Â [kN] [Nm] Â
M 6 – 5,0 0,3 6,5 2,2 6,5
M 8 – 6,0 0,6 16,0 4,0 16,0
M 10 – 7,0 1,2 31,5 5,0 31,5
Notes, Work aid
31
HALFEN FRAMING CHANNELS AND ACCESSORIES
Light Duty Framing Systems
3 FQ
up to 2,5 kN
Support Structures
® pages 54 - 59
5
36
p.
® Welded or bolted-on HALFEN
34
Pipe Clamps, Pipe Supports
5
/28 38 31
28 p. HM
HM ®
/26 40
26 p.
HM ®
Notes, Work aid
/15 42
28 p.
7 HM ®
/12
Note: If high load alternation
20 (dynamic loads) occurs, hot rolled
HM
channels, e.g. HM 40/22, are to be
used.
32
HALFEN FRAMING CHANNELS AND ACCESSORIES
Light Duty Framing Systems
Accessories
28 26
28 2
28
26
15
12 12 12
Design Properties
3
A number of light duty HALFEN
Framing channels are also available as
HTA Channels for casting into
concrete.
Support Structures
® page 94
Con
cre
HM te
or
HL
Cantilevers
HTA
5
Selection of HALFEN T-head bolts and locking plates Pipe Clamps, Pipe Supports
7
pages 35 - 43 pages 35 - 43
33
HALFEN FRAMING CHANNELS
Channel 36/36
HM 36/36 = plain back Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
HL 36/36 = slotted back rial, dard weight section inertia modulus point at span L
finish = loading
36 y z y z F
max F
1 for Stock To y y
L L [m]
explan. no. order x z x z
see p. = max F
52 G A Iy Iz Wy Wz À 0,50 1,00 1,50
[kg/m] [cm²] [cm4] [cm4] [cm³] [cm³] [kN] £L[cm] F [kN]
2,5 HM 36/36 0280-. .
36
wb 070-00001
2,19 2,79 4,51 5,85 2,18 3,25 4,4 44,0 3,9 1,9 1,0
fv 070-00002
Accessories
A4 070-00003
2 HL 36/36 0281-. .
wb 050-00001
18 fv 2,00 2,42 3,65 5,78 1,97 3,21 4,4 36,0 3,3 1,6 0,8
050-00003
A4 050-00002
Nominal dimensions Length: 6000 mm Order example: HM 36/36 - fv - 6000 or Stock no. 0280.070-00002
[mm]
À see note  on p. 55
Design Properties
15
Support Structures
6
36/3
HM 40
4
60
/36
36
HL
Cantilevers
5
Base channel for System 36 Series
Pipe Clamps, Pipe Supports
HALFEN 36 Series
Cantilevers:
® page 77
6
Other channel data, design properties Channel-accessories
SDM 36/6 PA 18 H HPE 36/36
Max. tensile / Max. load
Channel
data transverse compression Sound Channel Channel
load member attenuator closer end cap
strip
Notes, Work aid
y z
F
HALFEN System HALFEN 36 Series
7 36 Series: Fittings: x
y
z FZ FQ
® page 70 - 71 ® page 71
34
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channel 36/36
HS 38/17 M 10 M 12 M 16 M 10 M 12 M 16
Accessories
60 60 gv 60 gv 60 gv 60 A4-70 60 A4-70 60 A4-50
60 fv 8.8 2
70 70 fv 8.8
80 80 gv 80 gv 80 gv 80 A4-70 80 A4-50
80 Li 80Li A4-50 80Li A4-50
100 100 gv 100 gv 100 gv 100 A4-50 100 A4-50
Li = Left hand thread 100 fv
Design Properties
125 125 gv 125 gv
Support Structures
gv A4 Material/finish T-head bolts (® S. 53)
GWP 38/17 a b d
Bolt-accessories
Locking plates Thread Thread [mm] [mm] [mm] SIC
fv = h.d. galvanised, strength grade 4.6 4
M6 M6 33,5 17,5 6 Lock washers gv = electroplated, strength grade 4.6
b a for bolt HS 38/17 fv 8.8 = h.d. galvanised, strength grade 8.8
M8 M8 33,5 17,5 6
d
Cantilevers
A2-70 = Stainless steel grade A2-70
M 6 2,2
M 8 4,0
SIC 5
M 10 5,7 ® page 45
FS M 12 5,7
Pipe Clamps, Pipe Supports
À Note: Do not exceed channel load capacity! See also p. 54 - 59 (design properties). = Standard = to order
35
HALFEN FRAMING CHANNELS
Channel 38/17
HM 38/17 Á Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
[mm]
A2 020-00003
2 A4 020-00004
Length: 6070 mm Order example: HM 38/17 - fv - 6070 or Stock no. 0280.020-00002
Á Material: Stainless steel W 1.4547, À see note  on p. 55
Material order code HCR, on request.
Design Properties
3
/17
38 Other channel data, design properties Channel-accessories
HM
SDM 36/6 PA 18 H
Channel Max. tensile /
transverse Sound Channel closer
data
load attenuator strip
y z
Support Structures
y
x z FZ FQ
4
5
Pipe Clamps, Pipe Supports
6
Notes, Work aid
36
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channel 38/17
HS 38/17 M 10 M 12 M 16 M 10 M 12 M 16
Accessories
60 60 gv 60 gv 60 gv 60 A4-70 60 A4-70 60 A4-50
60 fv 8.8
2
70 70 fv 8.8
80 80 gv 80 gv 80 gv 80 A4-70 80 A4-50
80 Li 80Li A4-50 80Li A4-50
100 100 gv 100 gv 100 gv 100 A4-50 100 A4-50
Li = Left hand thread 100 fv
Design Properties
125 125 gv 125 gv
Support Structures
gv A4 Material/finish T-head bolts (® S. 53)
GWP 38/17 a b d
Bolt-accessories
Locking plates Thread Thread [mm] [mm] [mm]
SIC fv = h.d. galvanised, strength grade 4.6 4
M6 M6 33,5 17,5 6 Lock washers gv = electroplated, strength grade 4.6
b a M8 M8
for bolt HS 38/17
33,5 17,5 6 fv 8.8 = h.d. galvanised, strength grade 8.8
d
perm. load Thread loading capacity [kN] A2-50 = Stainless steel grade A2-50
Cantilevers
SIC
M 6 2,2 A2-70 = Stainless steel grade A2-70
À Note: Do not exceed channel load capacity! See also p. 54 - 59 (design properties). = Standard = to order
37
HALFEN FRAMING CHANNELS
Channels 28/28 and 26/26
HM 28/28 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
52
4 4
[kg/m] [cm²] [cm ] [cm ] [cm³] [cm³] [kN] £L[cm] F [kN]
HM 28/28 0280. . .
wb 050-00001
sv 050-00003 1,36 1,73 1,70 2,01 1,08 1,49 3,0 31,0 1,9 0,9 0,4
Accessories
12
fv 050-00002
2 Nominal dimensions A4 050-00004
[mm] HL 28/28 0281. . .
12, wb 060-00001
5
sv 060-00003 1,22 1,48 1,33 1,98 0,95 1,47 3,0 25,5 1,5 0,7 0,3
fv 060-00002
/28 A4 060-00004
8 28
Design Properties
HALFEN 28 Series y
x z
Fittings:
4 ® page 73
pages 54 - 57 page 59 page 50 page 46
HM 26/26 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
rial, dard weight section inertia modulus point at span L
HL 26/26 26
Cantilevers
finish = loading
y z y z F
5 max F
HM 26/26 0280. . .
0,82 1,05 0,94 1,18 0,64 0,91 1,10 50,0 1,10 0,51 0,23
sv 040-00001
12 HL 26/26 0281 . . .
0,72 0,89 0,73 1,16 0,56 0,89 1,10 40,0 0,90 0,40 0,18
6 sv 070-00001
Nominal dimensions Length: 6000 mm Order example: HM 26/26 - sv - 6000 or Stock no. 0280-040-00001
[mm] À see note  on p. 55
Other channel data, design properties Channel-accessories
12, Max. tensile / SDM 28/6 HPE 26/26
5 Channel transverse Sound Channel
data load attenuator end cap
Notes, Work aid
6 y z
6 2 6/2 F
/2
7 26 HL 25
HM y
40 x z
38
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channels 28/28 and 26/26
HS 28/15 Length l M 6 M 8 M 10 M 12 M 8 M 10
40 fv 8.8 40 A4-70
Accessories
50 50 gv 50 gv 50 gv 50 gv 50 A2-70
50 fv 50 A4-70 2
50 Li 50 Li A4-50
60 60 gv 60 gv 60 gv 60 A4-70
80 80 gv 80 gv 80 gv 80 A4-70
Li = left hand thread 100 100 gv 100 gv 100 A4-50
Design Properties
125 125 gv 125 A4-50
150 150 gv 150 gv 150 A4-50
200 200 gv 200 A4-50 3
Oder example: HS 28/15 - M 10 x 50 - gv
Calculation of
bolt length l requ.
® p. 9
Support Structures
GWP 28/15 Bolt-accessories
Locking plate Thread Thread [mm] [mm] [mm] fv = h.d. galvanised, strength grade 4.6
SIC
M 6 M 6 24,5 3 13,0 4 Lock washers gv = electroplated, strength grade 4.6
b a
M 8 M 8 24,5 3 13,0 4 for bolt HS 28/15 fv 8.8 = h.d. galvanised, strength grade 8.8 4
d
Cantilevers
FS ® page 45
5
T-head Max. pull out Max. longitudinal load Max. pull out Max. longitudinal load
bolts - per T-head bolt per Halfen T-head bolt per T-head bolt per Halfen T-head bolt
load
capa- 6
cities À
FS FL FS FL
grade grade grade tightening grade tightening grade grade grade tightening
4.6 8.8 4.6 torque 8.8 torque A2/A4 - 50 A2/A4 - 70 A2/A4 - 50/70 torque
[kN] [kN] [kN] [Nm] [kN] [Nm] [kN] [kN] [kN] [Nm]
Notes, Work aid
À Note: Do not exceed channel load capacity! See also p. 54 - 59 (design properties). = Standard = to order
Á Assembly note: First insert locking plate to channel, then screw in thread bar. Â Assembly note: Insert locking plate inclined through channel chase.
39
HALFEN FRAMING CHANNELS
Channels 28/15 and HM 315
HM 28/15 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
Nominal dimensions
[mm] A2 010-00004
2 A4 010-00003
HL 28/15 0281. . .
wb 080-00001
fv 080-00004 0,86 1,16 0,32 1,35 0,40 0,98 3,9 7,0 0,69 0,17 0,08
A2 080-00002
A4 080-00003
Design Properties
y FQ
x z FZ
4
pages 54 - 57 page 58 page 59 page 50
HM 315 (C 30)
Cantilevers
Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
30 rial, dard weight section inertia modulus point at span L
5 finish = loading
y z y z F
max F
7 5
31
HM
Subject to alterations
40
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channels 28/15 and 315
HS 28/15 Length l M 6 M 8 M 10 M 12 M 8 M 10
40 fv 8.8 40 A4-70
Accessories
50 50 gv 50 gv 50 gv 50 gv 50 A2-70
50 fv 50 A4-70 2
50 Li 50Li A4-50
60 60 gv 60 gv 60 gv 60 A4-70
80 80 gv 80 gv 80 gv 80 A4-70
Li = left hand thread 100 100 gv 100 gv 100 A4-50
Design Properties
125 125 gv 125 A4-50
150 150 gv 150 gv 150 A4-50
200 200 gv 200 A4-50 3
Order example: HS 28/15 - M 10 x 50 - gv
Calculation of
Á High corrosion resistant Halfen T-head bolts bolt length l requ.
HS 28/15, order code HCR, on request.
® p. 9
Support Structures
GWP 28/15 Bolt-accessories
Locking plates Thread Thread [mm] [mm] [mm] fv = h.d. galvanised, strength grade 4.6
SIC
for Chs. 28/15 M 6 M 6 24,5 3 13,0 4 gv = electroplated, strength grade 4.6
Lock washers
and 315 (C 30)
M 8 M 8 24,5 3 13,0 4 for bolt HS 28/15 fv 8.8 = h.d. galvanised, strength grade 8.8 4
b a M 10 M 10 33,5 2 17,5 5 gv 8.8 = electroplated, strength grade 8.8
d
Cantilevers
FS ® page 45
5
T-head Max. pull out Max. longitudinal load Max. pull out Max. longitudinal load
bolts - per T-head bolt per Halfen T-head bolt per T-head bolt per Halfen T-head bolt
load
capa- 6
cities À
FS FL FS FL
grade grade grade tightening grade tightening grade grade grade tightening
4.6 8.8 4.6 torque 8.8 torque A2/A4 - 50 A2/A4 - 70 A2/A4 - 50/70 torque
[kN] [kN] [kN] [Nm] [kN] [Nm] [kN] [kN] [kN] [Nm]
Notes, Work aid
À Note: Do not exceed channel load capacity! See also p. 54 - 59 (design properties). = Standard = to order
Á Assembly note: First insert locking plate to channel, then screw in thread bar. Â Assembly note: Insert locking plate inclined through channel chase.
41
HALFEN FRAMING CHANNELS
Channel 20/12
HM 20/12 Mate- Stan- Channel Cross Moment of Section Max. perm. Bending capacity
Framing Channels, Bolts
see p. = max F
52 G A Iy Iz Wy Wz À 0,50 1,00 1,50
[kg/m] [cm²] [cm4] [cm4] [cm³] [cm³] [kN] £L[cm] F [kN]
10
HM 20/12 0280 . .
A2 030-00002
2 HL 20/12 0281 . .
wb 090-00001
fv 090-00002 0,45 0,53 0,09 0,35 0,14 0,36 2,24 4,6 0,19 0,05 0,02
A2 090-00003
Length: 6000 mm Order example: HM 20/12 - fv - 6000 or Stock no. 0280.030-00003
À see note  on p. 55
Design Properties
pages 54 - 57
4
Cantilevers
5
Pipe Clamps, Pipe Supports
6
Notes, Work aid
Subject to alterations
42
HALFEN T-HEAD BOLTS AND ACCESSORIES
for Channel 20/12
M 6 M 8 M 8
HS 20/12 Material / finish Halfen T-head bolts (® p. 53)
Accessories
Oder example: HS 20/12 - M 8 x 40 - gv
2
gv A4
GWP 20/12 a b d
Design Properties
Thread Thread
Bolt-accessories
Locking plates [mm] [mm] [mm]
for Channel 20/12 SIC 20/12
M 5 M 5 16 9 4 Lock washers
M 6 M 6 16 9 4
3
b a
d
Support Structures
M 6 1,9
® page 45
FS 4
Cantilevers
5
Halfen for mild steel channels for stainless steel channels
T-head Max. pull out Max. longitudinal load Max. pull out Max. longitudinal load
bolts - per T-head bolt per Halfen T-head bolt per T-head bolt per Halfen T-head bolt
Pipe Clamps, Pipe Supports
load = Standard
capa- = to order
cities À
FS FL FS FL 6
grade grade tightening grade grade tightening
4.6 4.6 torque A2 - 70 A2 - 70 torque
Thread Ø [kN] [kN] [Nm] [kN] [kN] [Nm]
À Note: Do not exceed channel load capacity! See also p. 54 - 59 (design properties).
Subject to alterations
43
HALFEN FRAMING SYSTEMS ACCESSORIES
Threaded Rods, Hexagon Head Bolts, Nuts, Washers
GWS gv A4 gv A4
US
Framing Channels, Bolts
Length Load D d s
Threaded rod electroplated Washers
DIN 975 strength grade 4.6 Stainless steel A4-70 cap. DIN 440, electroplated Stainless steel A4
Thread Thread [mm] [kN] 9021 DIN for bolt for bolt [mm] [mm] [mm]
S
M 8 M 8 1000 4,0 9021 M 8 M 8 24 8,4 2
M 10 M 10 1000 6,4 9021 M 10 M 10 30 10,5 2,5
M 12 M 12 1000 9,3 d 440 M 12 45 13,5 4
M 16 M 16 1000 17,3 D 9021 M 12 M 12 37 13 3
M 20 M 20 1000 27,0 9021 M 16 M 16 50 17 3
M 24 1000 38,8 440 M 20 72 22 6
Accessories
HSK gv 8.8 A4 US gv A4
S S D d s
Hex head bolt Washers
electroplated, s.gr. 8.8 Stainless steel A4 DIN EN electroplated Stainless steel A4
DIN 933 or DIN 125
Dimension Dimension [mm] [mm] for bolt for bolt [mm] [mm] [mm]
ISO 4017
S
(without nut)
Design Properties
M 6 x 12 M 6 M 6 12 6,4 1,6
10 10
M 6 x 25 M 8 M 8 16 8,4 1,6
M 8 x 25 M 8 x 25 d M 10 M 10 21 10,5 2
3 M 8 x 40
13 13
M 12 M 12 24 13 2,5
D
M 10 x 20 M 16 M 16 30 17 3
M 10 x 30 M 10 x 30 M 20 M 20 37 21 3
M 10 x 45 M 10 x 45 M 24 44 25 4
17 16
M 10 x 60 M 27 50 28 4
M 10 x 70 M 30 56 31 4
Support Structures
M 12 x 22 fv A2 D d s
M 12 x 25 M 12 x 25 h.d. galvanised Stainless steel A2
4 M 12 x 30 M 12 x 30 for bolt for bolt [mm] [mm] [mm]
M 12 x 40 M 12 x 40 — M 8 17 8,4 1,6
19 18
M 12 x 50 M 10 M 10 21 10,5 2
M 12 x 60 M 12 x 60 M 12 M 12 24 13 2,5
Hex head bolts are
M 12 x 80 M 12 x 80 M 16 M 16 30 17 3
used in combina-
tion with HALFEN M 12 x 90 Order example:
locking plates M 16 x 40 M 16 x 40 US - gv - M 12 - DIN 125
Cantilevers
24 24
(® pages 9 - 43) M 16 x 60 M 16 x 60
5 M 16 x 90 M 16 x 90
electroplated s.gr. 8 Stainless steel A4 DIN ISO DIN Adjustment h.d. galvanised À
Hexagon nut Stainless steel A4
[mm] [mm] [mm]
coupler d
[mm] [mm] [mm] [kN]
DIN 934 or Thread Thread Type Type
ISO 4032 M 6 M 6 10/ 5 10/ 6 11,5 1 1 6 40 13 1,5
(= DIN EN 24032)
6 M 8 M 8 13/6,5 13/7,5 15,0 2 2 8 50 17 3,3
M 10 M 10 17/ 8 16/ 9,5 19,6 3 3 10 50 17 5,0
M 12 M 12 19/10 18/12 21,9 À Max. recomm. load Typical installation: fixing of
d
M 16 M 16 24/13 24/15,5 27,7 a suspended load under a
M 20 M 20 30/16 30/19 34,6 reinforced concrete bridge.
e
M 24 36/19 36/22 41,5
fv A2 S/m S/m e F
Notes, Work aid
44
HALFEN FRAMING SYSTEMS ACCESSORIES
Coupler Sleeves, Ring Nuts, Square washers
L
L
Accessories
- gv Load
- fv d
SKM -A4 S L Load RM cap. 2
Hexagonal rod cap. Ring nut C 15, electropl. Â
h.d. galvanised Stainless steel A4
coupler with À DIN 582 M Thread [mm] [kN]
view hole Thread Thread [mm] [mm] [kN]
M 8 20 1,4
M 10 M 10 13 40 6,4
M 10 25 2,3
M 12 M 12 17 40 9,3
M 12 30 3,4
L
M 16 M 16 22 50 17,3
M 16 35 7,0
Design Properties
Order example: SKM - fv - M 12 d
M 20 40 12,0
s Order example: RM - gv - M 12
3
À Recomm. maximum working load
with centre pull out
SPH -A4 -A4 D D
Turnbuckle Á Dimension D for finish - gv/-A4
Stainless steel A4 Stainless steel A4 für für
with right- M12 M16
 Recomm. maximum centre pull out
hand / left- Thread M 12 Thread M 16 in accordance with DIN 582
hand × Length L [mm] × Length L [mm] [mm] [mm]
Support Structures
thread VUS - fv -A4
L
VUS 49/30 M 10 M 10 37 x 37 x 5
- gv -A4
Cantilevers
SIC Fits to for channel M 12 M 12 37 x 37 x 5
electropl. Stainless Halfen bolt 54/33, d
steel A4 49/30 a b
M 16 M 16 37 x 37 x 5 5
M 20 M 20 37 x 37 x 5
38/17 52/34, d
SIC - 40/22 - gv SIC - 40/22 -A4 M16 50/30
40/22 a b
SIC - 38/23 - gv 38/23 M16
SIC - 29/20 - gv 29/20 M12 VUS 72/49 M 20 M 20 54 x 54 x 6
for channel M 24 M 24 54 x 54 x 6
6
38/17
SIC - 38/17 - gv SIC - 38/17 -A4 M12, M10 72/48, d
40/22 M 27 M 27 54 x 54 x 6
72/49 M 30 M 30 54 x 54 x 6
SIC - 28/15 - gv SIC - 28/15 -A4 28/15 M8, M10 a b
SIC - 20/12 - gv SIC - 20/12 -A4 20/12 M8
Order example:SIC - 38/17- gv VUS 41/41 M 6 M 6 40 x 40 x 6
for all d M 10 M 10 40 x 40 x 6
Notes, Work aid
45
HALFEN FRAMING SYSTEMS ACCESSORIES
Channel End Cap, Channel Closer Strip
HA
LFE
N
HPE 41/41 000-00003 41/41
HPE 41/22 000-00004 41/22
Type HPE
Colour: black
Accessories
3
Support Structures
PA
Channel closer strip
Cantilevers
PA 41 PA 22 PA 18 H
Order example: PA - 41 - KS - 3000
41 27,5 27,5 or Stock no. 0321.000-00002
Qual. / finish: 21 22 16,5
PVC, hard
6 (Plastic)
5
15
9
(KS)
Assembly diagram:
white grey grey
PA 22
41
Qual. / finish:
15
21
steel,
HALFEN
Notes, Work aid
pre-
Framing channel
9
galvanised
e.g. HM 52/34
7 (sv) fits to channel: fits to channel: fits to channel:
50/40, 50/30 52/34 36/36, Section slit to prevent
486, 38/17 dirt getting into interior
all Chs. 41 Series of channel.
46
HALFEN FRAMING SYSTEMS ACCESSORIES
HALFEN Beam Clamps HVT, U-clamp Plate, Halfen T-head bolt HS 41/41
Accessories
Clamp thickness: 22 mm Clamp thickness: 22 mm Clamp thickness: 22 mm
2
Designation Stock no. Designation Stock no. Designation Stock no.
Design Properties
= packing unit [pieces]
KUS 3
U-clamp plate, Assembly diagram U-clamp plate
fv
fits to all HALFEN
h.d. galv., str.gr.
Channels 41 Series
4 Type Stock no. e.g.
Chs. GWS-M12
KUS 0314.000-00001
Ø 13 41/83 or
A4 41/62
Support Structures
stainless steel GWP 41/41-M12
15
Cantilevers
35 35 fv 35 fv 35 A4-50 35 A4-50 A4-50 = electropl., str.gr. 4.6
50 50 fv = Stainless steel A4-50
5
Note:
L
Thread Ø
4.6
[kN]
4.6
[kN]
torque
[Nm]
A4 - 50
[kN]
A4 - 50
[kN]
torque
[Nm]
7
M 10 6,4 0,3 15 6,4 0,3 15 = Standard
M 12 8,0 0,5 25 9,3 0,5 25 = to order
À Note: Do not exceed channel load capacity! See also pages 54 - 59 (design properties).
47
HALFEN FRAMING SYSTEMS ACCESSORIES
Beam Clamps
49
81
44
Accessories
2 HCS TK - L HCS TK - 63
HCS TK
70 mm 70 mm
7 L
48
HALFEN FRAMING SYSTEMS ACCESSORIES
Beam Clamps
KLP - S fv Heel- for T-head Dimensions Perm. load recommended use with
No. 26 00002 without M 16 x 60 62,5 64 21 18 9 16,5 34,5 3,5 160 - 240 7-9 S 24
heel A 45, A 55
Accessories
No.40 1 00005 22 M 27 x 75 62,5 64 21 29 9 16,5 32,5 10,0
without A - 65
No.50 1 00006 M 27 x 75 62,5 64 21 29 9 16,5 32,5 10,0
heel 2
Order example: KLP - S - Nr. 26 - fv or Stock no. 0325.010-00002
Assembly diagram 1:
F1 Type KLP - S
m
c
Design Properties
k
Heel HALFEN Framing
channel 3
Load scheme KLP - S
À To be discontinued
The heel preventes twisting
Á T-head bolt M 16 x 80 is required
of the beam clamp by slotting
(bolt length depending from clamping heigth and channel type)
Support Structures
into the channel slit.
 Do not exceed channel load capacity!
à Check flange thickness first!
KLP - 60 fv
h.d. galvanised
Clamping Perm. load recommended use with 4
Beam clamps heigth h  Standard channel Standard channel crane / running
Stock no.
(formerly DIN 3568) Type 0325.020- [kN] I IPB rails Ã
[mm]
60/10 00001 10 F1 = 7,0 120 - 160 100 A65, S 33, S 41
LL 24 x 18 60/12 00002 12 T-head bolt 220 - 240 140 A100, S 49, A75
60 60/14 00003 14 M 16 x 60, grade 4.6 240 - 280 160 - 180 A120, S 54
60/16 00004 16 F2 = 11,25 300 - 340 200 - 220 S 64
18
Cantilevers
60/18 00005 18 Á T-head bolt 360 - 380 240 - 260 —
60/20 00006 20 Á M 16 x 60, grade 8.8 400 - 450 280 - 300 —
5
Order example: KLP - 60/10 - fv or Stock no. 0325.020-00001
75
F1 F2
tg
Ã
Pipe Clamps, Pipe Supports
Ã
h
35
HALFEN Framing
Load scheme KLP - 60
channel 6
HALFEN T-head bolt
e.g. HS 50/30 Assembly diagram 2:
Washer Type KLP - 60
e.g. US DIN 125
HALFEN Beam
clamp e.g. KLP
e.g. HL 50/40
Notes, Work aid
HALFEN Framing
channel e.g. HL 50/40
HALFEN Locking plate
7
e.g. GWP 50/40
Threaded rod with
lock nut and square
washer VUS
49
HALFEN FRAMING SYSTEMS ACCESSORIES
Sound Attenuator, Ductwork Suspensions
SDM
Framing Channels, Bolts
Material: À Please indicate length [m] when ordering. The product is kept in stock length of 30m.
2 Elastomer - technical quality (EPDM) Order example meter length: SDM 36/ 6 - roll, 16 m or Stock no. 0319.000-00003, 16m
45 ± 5 Shore Order example 4cm - piece: SDM 36/ 6 - 4cm - piece or Stock no. 0319.000-00004
SDM
Design Properties
3
Support Structures
5 Fixing point
• to concrete constructions:
HALFEN cast-in channel (® p. 94 - 96)
• to steel beam: beam clamp
Threaded rod
Pipe Clamps, Pipe Supports
electroplated ® page 44
Sound attenuator
6 Material: EPDM (see above)
Washers, nuts
7 electroplated
® p. 44
Channel end cap
HPE ® p. 46
50
HALFEN FRAMING SYSTEMS
Ductwork Suspensions
HALFEN cast-in
1
channel
e.g. HTA 38/17
(® p. 94)
see
B Using dowels observe
detail Locking plate
construction regulations
GWP 38/17
for concrete tension zone!
F (total) (® p. 37)
Accessories
Observe fire regulations! 2
Acc. to DIN 4102 reduced
F/2 F/2 load capacities! Washer US
(® p. 44)
Threaded rod
HPE (® p. 46) GWS with lock nut
(® p. 44)
Design Properties
£ 100 mm £ 100 mm
Support Structures
Weigth per metre 120 kg/m
Suspension distance 1,25 m
F(total) 120,0 x 1,25 4
150,0 kg ~ 1,5 kN
q = 120 kg/m F(total) = weight per metre x selected:
suspension distance Ch. HL 28/28 (perm. F(total) = 3,0 KN)
[kg/m x m]
Cantilevers
1,25 1,25
41
28
28 26
50 36
41
51
HALFEN FRAMING SYSTEMS
Materials, Finishs
Heavy Duty Framing Systems Medium Duty Framing Systems Light Duty Framing Systems
Framing Channels, Bolts
HALFEN Channels
hot
rolled
Accessories
cold
rolled
2
Material / finish: pages 6 - 21 pages 22 - 31 pages 32 - 43
Order code
wb Hot rolled: Material S235JR (St 37-2), Material S235JR (St 37-2),
Material S235JRG2 (RSt 37-2), DIN EN 10025 DIN EN 10025
Design Properties
Hot rolled: Material S235JR (St 37-2), Material S235JR (St 37-2),
fv
Material S235JRG2 (RSt 37-2), DIN EN 10025 DIN EN 10025
4 DIN EN 10025; resp. equivalent steel grade
Cold rolled: acc. to British Standard BS 1449, hot-dip galvanised,
Material S235JR (St 37-2), Sect. 1.4, 1991 zinc coating min. 50mm
DIN EN 10025
hot-dip galvanised,
hot-dip galvanised, zinc coating min. 50mm
hot-dip galvanised zinc coating min. 50mm
DIN EN ISO 1461
Cantilevers
pre-galvanised, pre-galvanised,
zinc coating min. 20mm zinc coating min. 20mm
Pipe Clamps, Pipe Supports
pre-galvanised
6 EN 10142
suitable for inddor applic.
A2 Material 1.4301
DIN 17440
52
HALFEN FRAMING SYSTEMS
HALFEN T-head Bolts, Assembly Accessories
Accessories
change to the new bolt shape, pages
both bolts are supplied. Patents À
9 - 19, 31,
pending. 35 - 43
2
pages 9 - 19, 31, page 44 page 44
35 - 43
Material / finish:
Order code
Design Properties
zinc coating min. 45 mm, zinc coating
strength grade 4.6 min. 45 mm,
according to DIN ISO strength grade 8
acc. to DIN ISO 3
Support Structures
Hot-dip galvanised
DIN 50976, according to DIN ISO
for threaded parts
DIN 267 Part 10 4
Cantilevers
5
gv 8.8 zinc electroplating, zinc electroplating,
zinc coating min. 12 mm, zinc coating approx.
Zinc electroplating strength grade 8.8 5 mm,
DIN 50961, according to DIN ISO strength grade 8.8
according to DIN ISO
Pipe Clamps, Pipe Supports
DIN EN 1403,
DIN EN ISO 4042
A2 Stainless steel A2
6
Grade A2-50,
A2-50
DIN 267, Part 11
Grade A4-50,
A4-50 DIN 267, Part 11
Stainless steel Grade A4-70 7
A4-70
DIN EN 10088 DIN 267, Part 11
resp. DIBt approval
HCR Material No. 1.4529, grade HCR-50
certificate Z-30.3-6
acc. to DIN EN ISO 3506-1 (on req.)
53
HALFEN FRAMING SYSTEMS
HALFEN Framing Channels, plain back
Framing Channels, Bolts
1
y
x e2 L
z max F
G A e1 e2 Iy Iz Wy Wz W pl,y
Type
e1 Â
A2
A4
[kg/m] [cm²] [cm] [cm] [cm4] [cm4] [cm³] [cm³] [cm³] [kN] £ L [cm]
HM 72/48 – – 8,82 11,23 2,41 2,44 34,99 83,07 14,33 23,08 18,28 31,0 32
HM 52/34 – – 4,96 6,32 1,68 1,72 9,42 24,13 5,49 9,19 7,09 17,0 21
Accessories
HM 50/30 – – 3,23 4,11 1,56 1,44 5,23 14,15 3,35 5,78 4,34 11,0 19
2 HM 40/22 – – 2,12 2,70 1,23 1,07 2,02 5,85 1,65 2,96 2,19 5,7 21
hot rolled
Heavy Duty Framing Systems
HM 72/48 D – – 17,63 22,46 4,85 4,85 204,04 166,14 42,51 46,15 54,88 31,0 109
HM 52/34 D – – 9,93 12,65 3,40 3,40 56,19 48,26 16,53 18,56 21,73 17,0 76
HM 50/30 D – – 6,45 8,22 3,00 3,00 27,52 28,31 9,17 11,32 11,85 11,0 61
HM 40/22 D – – 4,23 5,39 2,30 2,30 10,25 11,69 4,66 5,85 5,79 5,7 62
Design Properties
HZM 38/23 NEW! – – – 2,42 3,09 1,33 0,97 2,11 6,17 1,59 3,25 2,31 12,0 20
3 HZM 29/20 NEW! – – – 1,51 1,98 1,12 0,88 1,02 2,42 0,91 1,67 1,31 8,0 15
HM 49/30 – 3,07 3,91 1,77 1,23 4,32 13,92 2,44 5,57 3,74 4,9 46
HM 40/25 – 2,08 2,66 1,47 1,02 2,01 6,06 1,36 3,03 2,10 3,8 33
HM 422 (C40) – – – 1,55 1,98 1,22 0,93 1,27 4,29 1,04 2,17 1,46 2,5 36
4 HM 41/41 – 2,62 3,33 2,34 1,79 7,16 9,22 3,06 4,46 4,41 5,6 49
HZM 41/41 – – 2,62 3,25 2,38 1,75 6,91 9,10 2,91 4,41 4,26 5,6 47
Medium Duty Framing Systems
HM 41/22 – 1,80 2,30 1,24 0,83 1,19 5,32 0,97 2,58 1,50 5,6 15
HZM 41/22 – – 1,79 2,22 1,26 0,81 1,16 5,21 0,92 2,52 1,43 5,6 14
HM 41/83 – – 4,28 5,39 4,46 3,80 42,50 17,00 9,52 8,23 13,41 5,6 148
cold rolled
HM 41/62 – – 3,49 4,36 3,41 2,79 20,18 13,10 5,92 6,35 8,38 5,6 92
Cantilevers
HM 41/41 D – – 5,23 6,67 4,13 4,13 35,81 18,44 8,67 8,93 11,97 5,6 132
5
HZM 41/41 D – – 5,11 6,51 4,13 4,13 33,74 18,38 8,16 8,90 11,36 5,6 126
HM 41/22 D – – 3,60 4,59 2,07 2,07 5,55 10,64 2,69 5,15 3,81 5,6 42
HZM 41/22 D – – 3,58 4,66 2,05 2,05 5,64 11,0 2,68 5,33 3,78 5,6 42
HM 41/62 D – – 6,85 8,72 6,20 6,20 108,11 26,21 17,45 12,69 24,31 5,6 269
Pipe Clamps, Pipe Supports
HM 36/36 – – 2,19 2,79 2,07 1,53 4,51 5,85 2,18 3,25 3,17 4,4 44
HM 38/17 – 1,77 2,26 1,01 0,69 0,79 4,05 0,78 2,16 1,17 4,8 11
HM 315 (C30) – – – 0,77 0,97 0,92 0,58 0,30 1,26 0,32 0,84 0,47 1,6 17
6 HM 28/28 – 1,36 1,73 1,58 1,22 1,70 2,01 1,08 1,49 1,54 3,0 31
HM 26/26 – – – – 0,82 1,05 1,48 1,12 0,94 1,18 0,64 0,91 0,89 1,1 50
HM 28/15 – 1,07 1,37 0,88 0,62 0,38 1,42 0,43 1,02 0,65 3,9 8
HM 20/12 – – 0,52 0,66 0,72 0,48 0,12 0,36 0,16 0,36 0,25 2,2 5
Heavy Duty Framing Systems Medium Duty Framing Systems Light Duty Framing Systems
7 toothing
.. .. /.. ..
../ .. ../ 3 41 ../
../ 3/6 HM HM
HM ZM HM
H Z L6
H ® p. 20
hot rolled cold rolled cold rolled cold rolled
54
HALFEN FRAMING SYSTEMS
HALFEN Framing Channels, plain back
Accessories
HM 50/30 5,4 2,7 1,2 3,9 1,6 0,7 9,0 4,5 1,3 HS / HSR 50/30 M10-M20 GWP 50/30 M 8-M16 12 - 13
HM 40/22 2,7 1,1 0,49 2,0 0,65 0,29 3,4 1,7 0,52 HS / HSR 40/22 M10-M16 GWP 40/22 M 6-M12 14 - 15
2
L = 1,00m 2,00m 3,00m 1,00m 2,00m 3,00m 1,00m 2,00m 3,00m
Heavy Duty Framing Systems
HM 72/48 D * 34,2 17,1 11,4 25,4 12,9 7,29 34,2 17,1 6,5 HS / HSR 72/48 M20-M30 GWP 72/48 M12-M20 8-9
HM 52/34 D * 13,5 6,7 3,4 10,2 4,5 2,0 12,2 6,1 1,8 HS / HSR 50/30 M10-M20 GWP 50/30 M 8-M16 10 - 11
HM 50/30 D * 7,3 3,6 1,6 5,5 2,2 0,9 5,8 2,9 0,8 HS / HSR 50/30 M10-M20 GWP 50/30 M 8-M16 12 - 13
HM 40/22 D * 3,6 1,3 0,6 2,7 0,8 0,3 2,2 1,1 0,3 HS / HSR 40/22 M10-M16 GWP 40/22 M 6-M12 14 - 15
Design Properties
L = 0,50m 1,00m 1,50m 0,50m 1,00m 1,50m 0,50m 1,00m 1,50m
HZM 38/23 4,1 1,4 0,6 3,0 0,8 0,3 4,4 2,2 0,6 HZS / HS 38/23 M12-M16 GWP 38/17 M12-M20 16 - 17
HZM 29/20 2,3 0,6 0,3 1,6 0,4 0,1 2,0 1,0 0,3 HZS / HS 29/20 M12 GWP 28/15 M 8-M16 16 - 17 3
HM 49/30 4,5 2,3 1,0 3,3 1,3 0,6 7,4 3,7 1,1 HS 50/30 M10-M20 GWP 50/30 M 8-M16 12 - 13
HM 40/25 2,5 1,0 0,4 1,9 0,6 0,2 3,4 1,7 0,5 HS 40/22 M10-M16 GWP 40/22 M 6-M12 14 - 15
HM 50/40 6,9 3,4 2,0 5,2 2,6 1,2 13,8 6,9 2,2 HS 50/30 M10-M20 GWP 50/3(4)0 M 6-M16 18 - 19
HM 486 3,3 1,6 0,7 2,5 0,9 0,4 6,7 2,5 0,7 HS 50/30 M10-M20 GWP 50/3(4)0 M 6-M16 18 - 19
Support Structures
HM 422 (C40) 1,8 0,69 0,41 0,18 3,6 1,1 0,33 HS 40/22 M10-M16 GWP 40/22 M 6-M12 14
0,31 1,3
L = 0,50m 1,00m 1,50m 0,50m 1,00m 1,50m 0,50m 1,00m 1,50m
HM 41/41 5,4 2,7 1,7 4,0 2,0 1,0 11,0 5,5 1,8 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 24 4
HZM 41/41 5,3 2,6 1,6 4,0 2,0 0,9 10,6 5,3 1,7 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 26
Medium Duty Framing Systems
HM 41/22 1,8 0,6 0,2 1,4 0,3 0,1 2,0 1,0 0,3 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 25
HZM 41/22 1,7 0,6 0,2 1,3 0,3 0,1 2,0 1,0 0,3 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 27
L = 1,00m 2,00m 3,00m 1,00m 2,00m 3,00m 1,00m 2,00m 3,00m
HM 41/83 * 8,3 4,1 2,5 6,3 3,1 1,5 8,2 4,1 1,3 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 29
HM 41/62 * 5,2 2,6 1,2 3,9 1,6 0,7 4,4 2,2 0,6 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 28
Cantilevers
L = 1,00m 1,50m 2,00m 1,00m 1,50m 2,00m 1,00m 1,50m 2,00m
HM 41/41 D * 7,4 4,9 3,7 5,6 3,7 2,8 14,9 6,6 3,7 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 24
5
HZM 41/41 D * 7,0 4,7 3,5 5,2 3,5 2,6 14,1 6,2 3,5 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 26
HM 41/22 D * 2,3 1,3 0,7 1,7 0,7 0,4 2,8 1,4 0,6 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 25
HZM 41/22 D * 2,3 1,3 0,7 1,7 0,7 0,4 2,8 1,4 0,6 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 27
HM 41/62 D * 15,1 10,1 7,5 11,4 7,6 5,7 26,8 13,4 7,5 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 28
Pipe Clamps, Pipe Supports
HM 36/36 3,9 1,9 1,0 3,0 1,4 0,6 7,8 3,9 1,1 HS 38/17 M10-M16 GWP 38/17 M 6-M12 34 - 35
HM 38/17 1,4 0,4 0,19 1,0 0,25 0,11 2,7 0,69 0,20 HS 38/17 M10-M16 GWP 38/17 M 6-M10 36 - 37
HM 315 (C30) 0,59 0,16 0,07 0,38 0,09 0,04 1,03 0,26 0,08 – – GWP 28/15 M 6-M10 40 - 41
HM 28/28 1,9 0,93 0,41 1,45 0,55 0,24 3,8 1,4 0,44 HS 28/15 M 6-M12 GWP 28/15 M 6-M10 38 - 39
6
HM 26/26 1,1 0,51 0,23 0,84 0,30 0,17 2,2 0,82 0,24 HS 28/15 M 6-M12 GWP 28/15 M 6-M10 38 - 39
HM 28/15 0,81 0,21 0,09 0,49 0,12 0,05 1,33 0,33 0,10 HS 28/15 M 6-M12 GWP 28/15 M 6-M10 40 - 41
HM 20/12 0,25 0,06 0,03 0,15 0,04 0,02 0,4 0,10 0,03 HS 20/12 M 6-M 8 GWP 20/12 M 5-M 6 42 - 43
55
HALFEN FRAMING SYSTEMS
HALFEN Framing Channels, slotted
Framing Channels, Bolts
1
y
x e2 L
z max F
e1 G A e1 e2 Iy Iz Wy Wz Wpl, y
Type
Â
A2
A4
[kg/m] [cm²] [cm] [cm] [cm4] [cm4] [cm³] [cm³] [cm³] [kN] £ L [cm]
H.D. Fr. Sys.
HL 50/ 40 – – 3,15 3,73 1,95 1,95 7,14 15,36 3,65 6,27 4,68 5,4 53,5
Accessories
2 HZL 63/63 – – – – 6,35 7,09 3,01 3,29 33,07 42,95 10,06 13,63 13,51 5,6 134,0
Medium Duty Fr. Systems
HZL 41/22 – – 1,57 1,87 1,13 0,94 0,97 5,15 0,86 2,49 1,23 5,6 12,0
Design Properties
HL 41/83 – – 3,93 5,02 4,19 4,07 37,07 16,93 8,85 8,20 12,03 5,6 133,0
3 HL 41/62 – – 3,14 3,99 3,16 3,04 17,27 13,03 5,47 6,31 7,35 5,6 81,0
Light D. Fr. Sys.
HL 36/36 – – 2,00 2,42 1,85 1,75 3,65 5,78 1,97 3,21 2,64 4,4 36
HL 28/28 – 1,22 1,48 1,39 1,41 1,33 1,98 0,95 1,47 1,25 3,0 25
HL 26/26 – – – – 0,72 0,89 1,29 1,31 0,73 1,16 0,56 0,89 0,72 1,1 40
HL 28/15 – 0,86 1,16 0,79 0,71 0,32 1,35 0,40 0,98 0,55 3,9 7
Support Structures
HL 20/12 – – 0,45 0,53 0,61 0,59 0,09 0,35 0,14 0,36 0,19 2,2 4
All load bearing values are calculated elastic-plastic À Observe minimum distance ae between Channel end and
4 according to DIN 18 800. load point (T-head bolt, locking plate):
Part safety coefficient gF = 1,4. Deflexion £ l/ 150. • Heavy and medium duty framing systems: ae ³ 30 mm
• light duty framing systems: ae ³ 20 mm
5 25
0
.
3 1/. ..
0 /4
0
3/6 ZL4 ./
L5 L6 L/H .
H HZ H HL
Pipe Clamps, Pipe Supports
D Heavy Duty Framing Systems Medium Duty Framing Systems Light Duty Framing Systems
6 Channel D L A a Channel D L A a Channel D L A a
HL [mm] [mm] [mm] [mm] HL / HZL [mm] [mm] [mm] [mm] HL [mm] [mm] [mm] [mm]
a 50/40 18 40 60 20 41/41 14 28 50 22 36/36 15 40 60 20
L 63/63 14 28 250 - 41/22 14 28 50 22 28/28 12,5 25 40 15
41/83 14 28 50 22 26/26 12,5 25 40 15
A
41/62 14 28 50 22 28/15 9 25 40 15
Notes, Work aid
20/12 9 25 40 15
7
Other hole sizes and spacings on request;
e.g. Channel 28/28 also with RL Ø 11 or
LL 11 x 40 every 60 mm.
56
HALFEN FRAMING SYSTEMS
HALFEN Framing Channels, slotted
HL 50/ 40 5,8 2,9 1,7 4,4 2,2 1,0 11,6 5,8 1,8 HS 50/30 M10-M20 GWP 50/40 M 6-M16 18 - 19
Accessories
GWP 41/41
M 6-FM12
HZL 63/63 16,2 8,3 5,5 11,7 6,1 4,1 33,6 16,8 7,4 HZS 41/41, 41/22 M 8-M16 GWP 41/22
M 6-M16
20 - 21 2
Medium Duty Fr. Systems
HL 41/41 4,7 2,3 1,4 3,6 1,8 0,87 9,4 4,7 1,5 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 24
HZL 41/41 4,6 2,3 1,4 3,4 1,7 0,84 9,2 4,6 1,5 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 26
HL 41/22 1,5 0,54 0,24 1,2 0,32 0,14 1,7 0,86 0,25 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 25
HZL 41/22 1,5 0,53 0,23 1,1 0,31 0,14 1,6 0,84 0,25 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 27
Design Properties
L = 1,00m 2,00m 3,00m 1,00m 2,00m 3,00m 1,00m 2,00m
3,00m
HL 41/83 7,5 3,7 2,2 5,6 2,8 1,3 7,4 3,7 1,1 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 29
HL 41/62 4,5 2,2 1,0 3,4 1,3 0,6 3,6 1,8 0,5 HZS 41/41, 41/22 M 8-M16 GWP 41/41 M 6-M16 28 3
L = 0,50m 1,00m 1,50m 0,50m 1,00m 1,50m 0,50m 1,00m 1,50m
Light D. Fr. Sys.
HL 36/36 3,3 1,6 0,88 2,5 1,1 0,52 6,2 3,1 0,94 HS 38/17 M10-M16 GWP 38/17 M 6-M12 34 - 35
HL 28/28 1,5 0,73 0,32 1,1 0,43 0,19 2,2 1,1 0,34 HS 28/15 M 6-M12 GWP 28/15 M 6-M10 38 - 39
HL 26/26 0,90 0,40 0,18 0,68 0,24 0,10 1,5 0,64 0,19 HS 28/15 M 6-M12 GWP 28/15 M 6-M10 38 - 39
HL 28/15 0,69 0,17 0,08 0,4 0,10 0,05 0,5 0,28 0,08 HS 28/15 M 6-M12 GWP 28/15 M 6-M10 40 - 41
Support Structures
HL 20/12 0,19 0,05 0,02 0,1 0,03 0,01 0,2 0,08 0,02 HS 20/12 M 6-M 8 GWP 20/12 M 5-M 6 42 - 43
Cantilevers
*) Possible bulging, tilting and buckling must be prevented by
appropriate measure.
5
Pipe Clamps, Pipe Supports
6
Notes, Work aid
57
HALFEN FRAMING SYSTEMS
Load Capacity Values for HALFEN Framing Channels
FL FL
Pipe Clamps, Pipe Supports
g
Transverse pull loads in the
transverse pull area
Q least effective position Q
aw
g < 60°
Load spacing ew
6 Q
58
HALFEN FRAMING SYSTEMS
Load Capacity Values for HALFEN Framing Channels
Example: e.g.
Accessories
M 6 2,0 5,1 1,8 3,8 72/48 498 41/41 81 actual Q = 36,1 x (1 - 60/111) (page 60 ® FS)
M 8 5,0 12,5 4,4 9,4 52/34 231 36/36 39
= 16,58 kN > 1,00 kN 2
M 10 10,0 24,9 8,7 18,7 50/30 99 38/17 30
M 12 17,5 43,7 15,3 32,8 40/22 52 315 7
M 16 44,4 111,0 38,8 83,3 38/23 28/28 For bolt bending with additional pull, diago-
87 20
nal pull or transverse pull, the loads should
M 20 86,5 216,4 75,7 162,3 29/20 52 26/26 7
be overlaid:
M 24 149,7 374,2 131,1 – 50/40 109 28/15 15
Design Properties
M 27 221,9 554,8 – – 486 53 20/12 5
299,9 749,7 – – 422
Z, Q £ perm. Z, Q (1 - M/ perm. M)
M 30 28
3
perm. Z, Q = perm. pull resp. diagonal pull
Note: resp. transverse load
The bending moment of T-head bolt MT perm. M = perm. bending moment T-head
must not exceed the perm. elbow support bolt
moment MS of HALFEN Channel.
Z, Q = existing pull resp. diagonal pull
Support Structures
resp. transverse load
M = existing bending moment T-head
bolt
4
Load capacity values for HALFEN Framing channels as compression members
Buckling detection acc.
to DIN 18 800
F À F = permitted working load
Part safety factor for forces g f = 1,4, E = 170 000 N/mm²
- load applied to Á F = permitted working load
Part safety factor for forces g f = 1,4, E = 210 000 N/mm²
Cantilevers
point P
F Channel data
HALFEN Channel Perm. working load F [kN] À 5
at member length L [mm]:
A e Iy Wy Wpl iy min 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Type [cm²] [cm] [cm4 ] [cm³] [cm³] [cm] F [kN] F [kN] F [kN] F [kN] F [kN] F [kN] F [kN] F [kN] F [kN] F [kN]
l = sk
HM 72/48 11,23 2,41 34,99 14,33 18,28 1,77 60,3 54,5 46,1 36,9 29,2 23,2 18,7 15,3 12,7 10,7
Pipe Clamps, Pipe Supports
HM 52/34 6,32 1,68 9,42 5,49 7,09 1,22 32,1 26,1 19,0 13,6 10,0 7,5 5,9 4,7 3,8 3,1
HM 52/34 D 12,65 3,40 56,19 16,53 21,73 2,11 54,7 53,2 47,4 41,3 35,6 30,4 25,9 21,9 18,4 15,6
HM 50/30 4,11 1,56 5,23 3,35 4,34 1,13 21,9 16,9 11,7 8,1 5,8 4,4 3,3 2,6 – –
z
HM 40/22 2,70 1,23 2,02 1,65 2,19 0,87 13,6 8,9 5,5 3,6 2,5 1,8 – – – –
6
S HM 50/40 4,27 2,18 8,66 3,97 5,55 1,42 22,9 19,6 15,2 11,3 8,5 6,5 5,1 4,1 3,4 2,8
y y
HL 50/40 3,73 1,95 7,14 3,65 4,68 1,38 19,1 16,3 12,5 9,3 7,0 5,4 4,2 3,4 2,8 2,3
e
P HZL 63/63 Á 7,09 3,01 33,07 10,06 13,51 2,16 26,8 26,4 23,3 21,3 19,2 17,1 15,2 13,4 11,9 10,5
z HM/HZM 41/41 3,25 2,38 6,91 2,91 4,26 1,46 16,9 14,6 11,5 8,7 6,6 5,1 4,0 3,2 – –
HM/HZM 41/41D 6,51 4,13 33,74 8,16 11,36 1,68 27,5 25,5 23,2 20,7 17,4 13,8 11,1 9,1 7,5 6,3
Note:
HZL/HL 41/41 2,90 2,18 5,87 2,69 3,70 1,42 14,4 12,5 9,8 7,4 5,6 4,3 3,4 2,7 – –
At higher excentricity,
Notes, Work aid
the max. load should HM 36/36 2,79 2,07 4,51 2,18 3,17 1,27 14,3 11,8 8,7 6,3 4,6 3,5 2,7 – – –
be calculated in terms HL 36/36 2,42 1,85 3,65 1,97 2,64 1,23 11,7 9,6 7,1 5,1 3,8 2,8 2,2 – – –
of buckling in HM 28/28 1,73 1,58 1,70 1,08 1,54 0,99 8,5 6,2 4,1 2,8 2,0 – – – – –
7
accordance to 1,48 1,39 1,33 0,95 1,25 0,95 6,7 4,9 3,2 2,2 1,5 – – – – –
HL 28/28
DIN 18 800.
HM 26/26 1,05 1,48 0,94 0,64 0,89 0,95 5,2 3,7 2,3 1,6 – – – – – –
HL 26/26 0,89 1,29 0,73 0,56 0,72 0,91 4,1 2,9 1,8 1,2 – – – – – –
59
HALFEN FRAMING SYSTEMS
Heavy and Light Duty Framing Systems
HALFEN
Framing Channels, Bolts
lower than those of number of other factors. Type Fits to chan- Perm. transverse loads de-
2 T-head bolts HSR: Because of T-head bolt nels HZM pend on the construction.
(® pages 54 - 59). nibs a friction-type connection is 38/23 resp. See also transverse load on
assured. 29/20 welded channels on p. 58.
Important: Do not exceed NEW!
tightening torque of T-head bolt. ® page 17
Design Properties
Max. pull out Max. longitudinal load per Halfen T-head bolt
for mild steel channels per T-head bolt
Halfen T-head bolts,
3 Material: fv, gv
FL FL
FS
À Type HS, grade 4.6 Type HS, grade 8.8 Type HSR, grade 8.8
grade grade at tightening at tightening at tightening
4.6 8.8 torque torque (n = 3) torque
Support Structures
Max. pull out Max. longitudinal load À Hafen T-head bolt with nibs.
for stainless steel channels per T-head bolt per Halfen T-head bolt Permitted load as per official
report FMPA Baden-
Pipe Clamps, Pipe Supports
60
HALFEN FRAMING SYSTEMS
System 41 Series for Medium Loading
Generally the max. loads In mild steel channels, the permissi- Generally the open C channels
of HALFEN Channels are ble load in longitudinal direction is determine the values. Perm.
lower than those of higher than in stainless steel chan- transverse loads depend on
T-head bolts nels - due to the increased grip of fla- the construction. See also
Accessories
(® pages 54 - 59). me-hardened locking-plate-teeth transverse load on welded
into the channel lips. channels on p. 58.
For stainless steel, we recommend 2
toothed channels.
Important: Do not exceed tighte-
ning torque of T-head bolt.
Design Properties
Perm. load capacities of locking plates and Halfen T-head bolts System 41 Series
Support Structures
41/41 41/22 for all channels 41 a. 63 Series for Channels for Channels for Channels
at at
Locking plates Halfen T-head bolts HM/HL HZM / HZL HLL
tightening tightening
GWP GWP HZS HZS d/b 41/22, 41/41, 41/22, 41/41, torque 41/22, 41/41 torque 4
41/41 41/22 41/41 41/22 [mm] 41/62, 41/83 63/63
Thread -SH,-SN [kN] Æ [kN] Å [kN] [Nm] Â [kN] Å [Nm] Â
M 6 – 6/ 20 5,0 1,0 2,2 12 1,0 12
M 8 – 8/ 20 6,0 2,4 4,0 28 2,4 28
M 10 – 9/ 20 7,0 3,5 5,0 55 3,5 55
M 12 À 11/ 20 9,0 À 5,0 À 5,0 À 75 3,6 À 55
F M 12 9/ 20 7,0 4,0 5,0 60 (50) 3,6 55 (50)
Cantilevers
M 16 Á À Æ 12/ 30 12,0 (7,0) À 7,5 À 7,5 À 125 (80) 4,5 À 95 (80)
5
for Stainless Steel Channels 5 Max. pull out Max. longitudinal load per Halfen T-head bolt
34,
Material: Stainless Steel A4
per Halfen T-head bolt
5 b
34, 34,5
20
Pipe Clamps, Pipe Supports
HZS
7,5
d 41/22 FL FL
GWP GWP FS
41/41 41/22
Note:
Do not exceed channel
for Channels 41 at tightening for Channels 41 at tightening 6
Locking plates Halfen torque torque
load capacity!
GWP GWP T-head bolts d/ b HM/HL HZM/HZL
Thread 41/41 41/22 HZS 41/22 [mm] [kN] Æ [kN] [Nm] Â [kN] [Nm] Â
M 6 – 6/ 20 5,0 0,3 6,5 2,2 6,5
M 8 – 8/ 20 6,0 0,6 16,0 4,0 16,0
M 10 – 9/ 20 7,0 1,2 31,5 5,0 31,5
Notes, Work aid
61
HALFEN FRAMING SYSTEMS
HALFEN POWERCLICK Framing System
Framing Channels, Bolts
1 kg
POWERCLICK SYSTEM 63
POWERCLICK SYSTEM 41
3
Suitable for pipes with nominal
kg
diameters up to 80 mm or 150 mm
with short spans or agreed applica-
tions
Support Structures
Catalogue PC 41 kg
kg
POWERCLICK SYSTEM 22
Cantilevers
Catalogue PC 41
Pipe Clamps, Pipe Supports
6 kg
POWERCLICK ACCESSORIES
Catalogue PC Z
7
kg
62
HALFEN FRAMING SYSTEMS
HALFEN POWERCLICK Framing System 63 for Heavy Duty
Channel
kg
Bolt set
Powerclick
Accessories
pre-assembled
in all 2
fittings
Design Properties
3
Also suitable:
locking plates
and T-head
Support Structures
bolts fitting kg
with channels
41/22
® page 31
kg 4
GWP 41/41
kg
kg
GWP 41/41SN
Cantilevers
5
HZS 41/41 kg
63
Base channel: Channel data:
HZL 63/63 Bending capacity Max. load Max. longitudinal load per T-head bolt: 6
at span L compression
63
member
F
N 2,5
5k F
7
L [m] FS FL
9,5 22 9,5
Locking plate GWP 41/41
3
Notes, Work aid
63
HALFEN FRAMING SYSTEMS
HALFEN System 52 Series for Heavy Duty, Overview
HVT 52 - 8
Accessories
2
Components to assembly, System 52 Series
HM 52/34 HVT 52-2
Examples
Beam with angle fittings HM 52/34
Design Properties
HM 52/34D
HVT 52/7
Beam with shoe
Support Structures
fittings, increased
load
capacity
4 External radius
• Assembly channel rings: as measure specification
Articulated
Manufacturing of channel rings cantilever
and lateral channel slotting
also to your measurements
Channel slot
inside
Cantilevers
5 Articulated beam
Channel ring
Articulated brace
Pipe Clamps, Pipe Supports
member
F
15 22 15 FL FL
F
L [m]
Type HS, grade A4-50
Notes, Work aid
64
HALFEN FRAMING SYSTEMS
HALFEN Fittings System 52 Series
HVT - 52
5 25
190
All T-head 50 135 60
190 5
bolts and
locking plates 60
Accessories
of Type 50/30 120
are suitable. 2
180 180
147
HVT - 52 - 1 HVT - 52 - 2 HVT - 52 - 3 HVT - 52 - 4 HVT - 52 - 5
75
Design Properties
HSR 50/30
135
M16, M20 125 200
180
with
nibs 5
3
75
5 230
2× HVT 52-8 5
200
combined to 1
HVT - 52 - 6 HVT - 52 - 7 HVT - 52 - 8 HVT - 52 - 9
binder
Support Structures
Designation Stock no. Designation Stock no.
Unless otherwise stated, the follo-
HS 50/30 0312.040- 0312.040-
M10-M20
wing dimesions apply for all fittings.
FV = hot dip galvanised A4 = Stainless steel W 1.4571/1.4401
4
HVT - 52 - 1 - FV 00001 HVT - 52 - 1 - A4 À 00011
HVT - 52 - 2 - FV 00002 HVT - 52 - 2 - A4 À 00012
HVT - 52 - 3 - FV 00003 HVT - 52 - 3 - A4 À 00013
HVT - 52 - 4 - FV 00004 HVT - 52 - 4 - A4 À 00014
GWP 50/30 25 HVT - 52 - 5 - FV 00005 HVT - 52 - 5 - A4 À 00015
M8-M16 HVT - 52 - 6 - FV 00006 HVT - 52 - 6 - A4 À 00016
RL Ø 18 HVT - 52 - 7 - FV 00007 HVT - 52 - 7 - A4 À 00017
Cantilevers
8 50 HVT - 52 - 8 - FV 00008 HVT - 52 - 8 - A4 À 00018
HVT - 52 - 9 - FV 00009 HVT - 52 - 9 - A4 À 00019 5
Curved chan- Application examples: À to order
nels and
channel rings All part sketches show only one of
on request many possible applications.
Pipe Clamps, Pipe Supports
6
Notes, Work aid
65
HALFEN FRAMING SYSTEMS
Systems 41 and 22 Series, Standard Systems for Medium Duty, Overview
Framing Channels, Bolts
1 2 3
Accessories
2 HALFEN POWERCLICK is a standard POWERCLICK copes with every situa- ponents, for all channels only one and
support system for pipe assembly. All tion with standard system solutions.. the same HALFEN T-head bolt is
fittings are pre-converted with HAL- The catalogue HALFEN POWERCLICK necessary. The bolt is pre-assembled
FEN T-head bolts. Framing System 41 Series offers furt- within the fittings, is to be fixed in no
Using POWERCLICK, assembly times her information. With clearly arran- time at all and is partially load bearing
are reduced about 60%, and because ged data it is an important planning even before tightening.
of free system adjustment costly wor- aid for users. Every accessory part is Because of the easy weight of the
Design Properties
karounds become redundant. The introduced separately with all techni- components no lifting devices are
3 efficient dimensioning of POWER- cal data. Above all, the HALFEN Plan- required. Due to the flexible adjusting
CLICK System assures the same ning Service will support your project. site tolerances can be easiliy compen-
strength like conventional construc- POWERCLICK makes it easy. For all sated.
tions, but is more flexible. HALFEN applications only a few different com-
kg
Cantilevers
5
Pipe Clamps, Pipe Supports
® pages 68 - 69
HALFEN POWERCLICK
6 Framing System 22 Series
Notes, Work aid
66
HALFEN FRAMING SYSTEMS
HALFEN Fittings Systems 41 and 22 Series
Accessories
48 164
20 2
232
RL Ø 14
40
6
HVT 41 - 19 HVT 41 - 22
Application examples:
All part sketches show only one of many possible
applications. 47 138
98
90
Design Properties
À ® p. 47 90
89
Stock no. Stock no. 90 47 47
96
fv = h.d. galvanised A4 = Stl. steel A4 137
Designation
0312. .. 0312. ..
138 96 3
HVT 41 - 08 030-00001 51
42 51 51
HVT 41 - 10 030-00002 030-00049 HVT 41 - 27 HVT 41 - 31 HVT 41 - 33 HVT 41 - 34 HVT 41 - 35 HVT 41 - 36
HVT 41 - 11 030-00003
HVT 41 - 13 030-00004 030-00051
HVT 41 - 15 030-00005 030-00052
Support Structures
HVT 41 - 19 030-00006 43 47 178
HVT 41 - 22 030-00008 030-00054 48 50
47
HVT 41 - 23 030-00009 41
42 42
HVT 41 - 25 030-00010
83
55
47
96 4
HVT 41 - 26 030-00011 030-00057 21
41 96
HVT 41 - 27 030-00012 030-00058
HVT 41 - 31 030-00013 HVT 41 - 37 HVT 41 - 40 HVT 41 - 41R HVT 41 - 41L HVT 41 - 43 HVT 41 - 44
HVT 41 - 33 030-00014
38
137
120
47
47 40 60
41
Cantilevers
HVT 41 - 37 030-00018 98 138 Ø 14
8
HVT 41 - 40 030-00019 54 5
HVT 41 - 41L 030-00020 21 100 100
41
HVT 41 - 41R 030-00021 41 41 140
HVT 41 - 43 030-00022
HVT 41 - 45 HVT 41 - 46 HVT 41 - 47 HVT 41 - 49 HVT 41-57
HVT 41 - 44 030-00023
HVT 41 - 45 030-00024
Pipe Clamps, Pipe Supports
67
HALFEN FRAMING SYSTEMS
HALFEN Channel Ring System 41 Series
Channel ring
Framing Channels, Bolts
HCS - 41 - SRI
1 HCS - 41
- SRI
- GST
s)
a
iu
R
ad
Accessories
lr
- GET - STR
na
2
er
xt
(E
- GET - GST
Design Properties
3 Channel slot
Order example:
SRI - Channel ring
External radius Ra = 1000 mm
Channel:
HCS - 41 - SRI - P - fv - 1000
Support Structures
Assembly set 1 x Threaded rod M 12 x 120 HZM 41/22 toothed, for material A4
5 1 x Hex. head bolt HSK - M12 x 25
3 x Hexagonal nut M 12 41
/2
0304. . . 41 22
Pipe Clamps, Pipe Supports
68
HALFEN FRAMING SYSTEMS
HALFEN Channel Ring System 41 Series
Type selection
50
ea len
Accessories
su
re th
0304. . . - GST 2
m
- GET
en
Design Properties
Order example:
GET - Articulated beam
- GET Articulated beam HCS - 41 - GET - P Delivery includes (dashed line): Order length LB = 800 mm 3
Channel HL 41/41, order length LB [mm]
with holes Channel:
HCS - 41 - GET - P - fv - 800
8 HCS - 41 - GET - M Delivery includes:
or Stock no. 0304.050-00002, LB = 800mm
Assembly set 1 x U-Fitting HVT 41 - 78
1 x HVT 41 - 58 Assembly set:
50 HCS - 41 - GET - M - fv
1 x Bolt fixing set HCS-41-B3
Support Structures
1 x Bolt fixing set HCS-41-B4 or Stock no. 0304.040-00002
Type selection
Designation Stock no.
4
20 Sys. measurement L S 0304. . . À Always specify order length LB [mm]
Material: fv = h.d. galvanised when ordering.
HCS - 41 - GET - P - fv - Length LB 050-00002 À
Order length L B 33
HCS - 41 - GET - M - fv 040-00002
Base Channel for System 41:
Material: A4 = Stainl. steel A4 HL 41/41 slotted, for mat. fv und A4
HCS - 41 - GET - P - A4 - Length LB 050-00001 À HZL 41/41 slotted, toothed, for mat. A4
HCS - 41 - GET - M - A4 040-00001
Cantilevers
14
5
41
- STR Articulated cantilever HCS - 41 - STR - P Delivery includes (dashed line): 28
Channel HL 41/41, Bestell-Length LB [mm] 50
with holes
/41 2,5
41
41
Pipe Clamps, Pipe Supports
L
HCS - 41 - STR - M Delivery includes:
/ HZ
7
Type selection
6
Locking plates
Designation Stock no. GWP 41/41F,
0304. . . M12
Sys. measurement L S Material: fv = h.d. galvanised
20
HCS - 41 - STR - P - fv - Length LB 080-00002 À Bending capacity Max. load
Order length L B HCS - 41 - STR - M - fv 090-00002 at span L compression
member
F
Notes, Work aid
69
HALFEN FRAMING SYSTEMS
HALFEN System 36 Series for Light Duty, Overview
1
HVT 36-2
+T-head bolts
HL 36/36 Advantage: With channel
HL 36/36 assembly through
slotted channel back.
Accessories
2
HVT 36-7
+T-head
bolts
HVT 36-7
Design Properties
+T-head HL 36/36
bolts
3
Support structures
for light duty Articulated
cantilever
4 Example:
Channel slot
inside
Articulated beam
Channel ring
Cantilevers
5
Articulated brace
• Assembly channel rings:
Manufacturing of channel rings Base channel for channel ring
HM 38/17 ® p. 36
and lateral channel slotting
Pipe Clamps, Pipe Supports
to your measurements.
Base channels: 36
Channel data:
6 HM / HL 36/36 Max. longitudinal load per T-head bolt
Bending capacity Max. load
2,5 at span L compression
36
member
F
9 18 9 F
L [m] FL
/3 6
36 15
Notes, Work aid
70
HALFEN FRAMING SYSTEMS
HALFEN System 36 Series for Light Duty, Fittings
Accessories
dimensions apply for all fittings. 110
LL 11 x 20
2
11 110
LL 11 x 20
LL 11 x 25 36
LL 11 x 30 36
r=3 LL 11 x 25 36
36 LL 11 x 25
LL 11 x 50
5 80
Design Properties
33 HVT 36 - 1 HVT 36 - 2 HVT 36 - 3
All part sketches show only one of many
possible applications. 3
Support Structures
and washer U. 35 37 130
45 35 36
4
= Standard = to order Ø 11 Ø 11 4
80 4
Material Ø 11
fv = h.d. galvanised Stock no.
gv = electroplated HVT 36 - 4 HVT 36 - 5 HVT 36 - 6
HVT 36 - 1 -gv 0312.020-00001
HVT 36 - 2 -gv 0312.020-00002
HVT 36 - 3 -gv 0312.020-00003
Cantilevers
HVT 36 - 4 -gv 0312.020-00004
HVT 36 - 5 -gv 0312.020-00005 5
HVT 36 - 6 -gv 0312.020-00006
HVT 36 - 7 -fv 0312.020-00007 2 x LL 11 x 30
LL 13 x 26 HM 28/28
HVT 36 - 8 -gv 0312.020-00008
HVT 36 - 9 -fv 0312.020-00009 150
25
100
40 Ø 11
Pipe Clamps, Pipe Supports
150 20
6 60
Designation 60
Ø 13 60
A4 = Stainless steel Stock no. 135 65 20
4 220
A4
HVT 36 - 2 -A4 0312.020-00010
LL 13 x 26
6
HVT 36 - 7 HVT 36 - 8 HVT 36 - 9 À
HVT 36 - 7 -A4 0312.020-00011
À The fitting is fixed to channels by using T-head bolts Type HS 28/15 - M 10 x 25 and washer U, M10
DIN 9021
Notes, Work aid
71
HALFEN FRAMING SYSTEMS
HALFEN System 28 Series for Light Duty, Overview
1
Accessories
Support structures
for light duty
3 Example:
HL 28/28
HVT 28 - 2
+ T-head bolts
HL 28/28
Support Structures
HVT 28 - 7
+ T-head
bolts HL 28/28
4
HVT 28 - 7
+ T-head bolts
Cantilevers
• Frame constructions:
5 will be manufactured to your
measurements.
Delivery times on request.
Base channels:
Pipe Clamps, Pipe Supports
HM 28/28
HL 28/28 (slotted)
Channel data:
6 27
Bending capacity Max. load Max. longitudinal load per T-head bolt:
at span L compression
2 member
28
F
/28
28 12, 8 12 8
F
HM 5 L [m] FL
Notes, Work aid
72
HALFEN FRAMING SYSTEMS
HALFEN System 28 Series for Light Duty, Fittings
8 1
/28 8/2
28 2
HL
HM
Accessories
90
dimensions apply for all fittings.
90
LL 9 x 26
LL 9 x 22 LL 9 x 14
2
9
LL 9 x 14
70
28
LL 9 x 30
28 28
LL 9 x 26 35 LL 9 x 26
LL 9 x 30
4
Design Properties
HVT 28 - 1 HVT 28 - 2 HVT 28 - 3
25
Support Structures
103 Ø9
Ø9
= Standard = to order Ø9
63 4
28 27 33
Material
fv = h.d. galvanised Stock no.
gv = electroplated HVT 28 - 4 HVT 28 - 5 HVT 28 - 6
HVT 28 - 1 - gv 0312.010-00001
HVT 28 - 2 - gv 0312.010-00002
HVT 28 - 3 - gv 0312.010-00003
Cantilevers
HVT 28 - 4 - gv 0312.010-00004
HVT 28 - 5 - gv 0312.010-00005 5
HVT 28 - 6 - gv 0312.010-00006
HVT 28 - 7 - fv 0312.010-00007 5 LL 9 x 18 LL 9 x 18 Ø9
HM 36/36
HVT 28 - 8 - gv 0312.010-00008 80 100
HVT 28 - 9 - fv 0312.010-00009
100 100 20 40
40
Pipe Clamps, Pipe Supports
40
160 20
2 x LL 9 x 26 Ø9 3
LL 9 x 18
73
HALFEN FRAMING SYSTEMS
Cantilevers
Application
Framing Channels, Bolts
1
Fixing with dowel or with T-head bolts to
cast-in HALFEN Channel
2
Cantilever of standard HALFEN Channel, to be
combined with T-head bolts,
HALFEN Fittings and System accessories.
Design Properties
available.
Type selection
Due to continuous covering of the different
cantilever lengths, the most cost-efficient
Cantilevers
6
Notes, Work aid
74
HALFEN FRAMING SYSTEMS
Cantilevers
50
100
1.4401 (A4)
135
L/2 L/2 LS L/3 L/3 L/3
LL 22 x 31
H1
[mm] 0310.080- [mm] 0310.080- F1 [kN] F1 [kN] F2 [kN] [mm] [mm]
500 00001 500 00008 9,00 15,00 7,50 450 330
600 00002 600 00009 8,00 15,00 7,50 475 380
700 00003 700 00010 7,00 15,00 6,50 500 430
Accessories
35 50
RL Ø 22
800 00004 800 00011 6,00 15,00 6,00 550 480
30°
900 00005 900 00012 5,50 15,00 5,50 600 530 2
1000 00006 1000 00013 5,00 15,00 5,00 650 630
1100 00007 1100 00014 4,50 14,00 4,50 700 730
Design Properties
(4x) 52/4
with matching FZ 600 16,89 15,00
T-head bolt FZ
34 HS 50/30 700 16,83 15,00
3
® page 10 - 11 800 15,86 15,00
KON
900 15,47 15,00
LS FQ 52/3
1000 15,00 15,00
1100 14,72 14,00
Order example Designation: KON 52/2 - fv - 800 [mm]
or Stock no.: 0310.080-00004 KON 52/3 + KON 52/4
Support Structures
for lateral bracing
4
Fittings fv A4 Assembly diagram
fits to
for Cantilevers 52/2 Oder bolts etc. separately.
h.d. galvanised Stainl. steel cantilevers
W 1.4571/ 52/2
1.4401 (A4)
Cantilevers
Ø 13 532 00001 532 00012 500 100 400
602 00002 602 00013 600 150 450 KON 52/3 5
673 00003 673 00014 700 200 500
KON 52/3 744 00004 744 00015 800 250 550
Lst
815 00005 815 00016 900 300 600
961 00006 961 00017 1000 300 700
Pipe Clamps, Pipe Supports
FY
KON 52/4 - fv
45° or Stock no. 7
0310.100-00002 À Stainless steel cantilevers are fixed with
St
RL Ø13
L
Note: The max. load bearable of lateral locking plate GWP 50/30 - M 12
brace depends on permissible load FZ = Standard and T-head bolt HSK - M12 x 60,
r
75
HALFEN FRAMING SYSTEMS
Cantilevers
LL 13 x 26
h.d. galvanised Stainl. steel F1 F1 F2 F2 F3 F3 F3
51 W 1.4571/
1.4401 (A4)
70
25
L
1 length Stock no. length Stock no.
L/2 L/2 L L/3 L/3 L/3 L/4 L/4 L/4 L/4
180
21
[mm] 0310.010- [mm] 0310.010- F1 [kN] F1 [kN] F2 [kN] F3 [kN]
175 00001 175 00004 5,35 2,65 2,65 1,75
325 00002 325 00005 2,65 1,30 1,30 0,85
LL 13 x 26
475 00003 475 00006 1,75 0,85 0,85 0,55
fv A4 load capacity
KON 41/D LL 13 x 26
Cantilevers h.d. galvanised Stainl. steel F1 F1 F2 F2 F3 F3 F3
Design Properties
W 1.4571/
49
1.4401 (A4)
25
3 L length Stock no. length Stock no.
L/2 L/2 L L/3 L/3 L/3 L/4 L/4 L/4 L/4
180
21
[mm] 0310.030- [mm] 0310.030- F1 [kN] F1 [kN] F2 [kN] F3 [kN]
325 00001 325 00004 5,60 2,80 2,80 1,85
475 00002 475 00005 3,70 1,85 1,85 1,20
LL 13 x 26
625 00003 625 00006 2,80 1,40 1,40 0,90
Support Structures
fv A4 load capacity LL 13 x 26
KON 41/2 F1 F1 F2 F2 F3 F3 F3
Cantilevers h.d. galvanised Stainl. steel
W 1.4571/
50
1.4401 (A4)
25
Cantilevers
5 L length Stock no. length Stock no. L/2 L/2 LS L/3 L/3 L/3 L/4 L/4 L/4 L/4 H
[mm] 0310.020- [mm] 0310.020- F1 [kN] F1 [kN] F2 [kN] F3 [kN]
325 00001 325 00005 7,50 4,90 4,80 3,40
21
KON Z1 fv A4 = Standard
16 (® page 44)
Bracing for 350 5 h.d. galvanised Stainl. steel = to order
7 cantilevers 55 (Order T-head bolts, nuts
and cantilevers
Stock no. Stock no. 2 T-head bolts
5 separately)
HS 41/41
0310.110- 0310.110-
M 12 x 35
45 00002 00001 Possible assembly underneath cantilever
RL Ø 13 (® page 47)
(2 holes need to be made on site)
76
HALFEN FRAMING SYSTEMS
Cantilevers
25
L/2 L/2 L L/3 L/3 L/3 L/4 L/4 L/4 L/4 1
46
length Stock no. length Stock no.
L
120
[mm] 0310.050- [mm] 0310.050- F1 [kN] F1 [kN] F2 [kN] F3 [kN]
100 00001 100 00005 2,70 1,35 1,35 0,90
00002 00006
21
200 200 1,35 0,68 0,68 0,45
300 00003 300 00007 0,90 0,45 0,45 0,30 LL 13 x 20
6 400 00004 400 00008 0,70 0,35 0,35 0,20
Accessories
Connection length FZ FQ KON - Z1
FZ F1/2/3
forces [mm] [kN] [kN] 2
Channel HM 28/28
100 1,82 2,70
with matching
T-head bolt HS 28/15 200 1,82 1,36
( ® p. 38 - 39) 300 1,82 0,90 2 holes need to be made
FQ on site in channel back
400 1,89 0,70
Design Properties
fv A4 load capacity
KON 36/1
Cantilevers h.d. galvanised Stainl. steel F1 F1 F2 F2 F3 F3 F3
LL 13 x 26
3
25
W 1.4571/
1.4401 (A4)
46
75,5
L/2 L/2 L L/3 L/3 L/3 L/4 L/4 L/4 L/4
length Stock no. length Stock no.
180
L [mm] 0310.060- [mm] 0310.060- F1 [kN] F1 [kN] F2 [kN] F3 [kN]
300 00001 300 00005 2,00 1,00 1,00 0,70
Support Structures
400 00002 400 00006 1,50 0,75 0,75 0,50
21
500 00003 500 00007 1,20 0,60 0,60 0,40
LL 13 x 26
600 00004 600 00008 1,00 0,50 0,50 0,33 4
Connection length FZ FQ KON - Z1
25 F1/2/3
forces FZ [mm] [kN] [kN]
Channel HM 36/36 300 2,07 2,10
with matching 400 2,07 1,50
T-head bolt HS 38/17 500 2,07 1,20 2 holes need to be made
( ® p. 34 - 35) FQ
600 2,07 1,00 on site in channel back
Cantilevers
5
fv A4 load capacity
KON 36/2 F1 F1 F2 F2 F3 F3 F3 LL 13 x 26
Cantilevers h.d. galvanised Stainl. steel
W 1.4571/
46 1.4401 (A4)
50
25
length Stock no. length Stock no. L/2 L/2 LS L/3 L/3 L/3 L/4 L/4 L/4 L/4
L
[mm] 0310.070- [mm] 0310.070- F1 [kN] F1 [kN] F2 [kN] F3 [kN]
H
Order example: KON 36/2 - fv - L = 500 mm or Stock no. 0310.070-00003 Subject to alterations
77
HALFEN FRAMING SYSTEMS
Pipe Clamps
HALFEN Pipe clamps are well suited for fittings in combination with HALFEN
Framing Channels, Bolts
Framing Systems. Due to the material thickness of HALFEN Pipe clamps which
are dimensioned by relating requirements, an optimum of material efficiency is
guaranteed.
1
HALFEN Pipe clamps are Using HALFEN Pipe fittings, spatial adjustment
available in a whole range of in all directions at any time is assured.
versions for pipe - Ø from 15
Accessories
to 530 mm.
2 For Alpha pipe fittings,
HALFEN also offers pipe
clamp, sound attenuation In case of loads in
insulation and pipe rest as a longitudinal di-
complete assembly set (Type rection of pipe
HCS - RAD) ® page 81 use cantilevers
with lateral bra-
Design Properties
cing,
e.g. b KON-Z1,
3 ® page 76
Support Structures
Assembly diagram:
5 Example: HALFEN Pipe clamp HRS - A on
HALFEN Cantilever KON - 52/2 (® Assembly set HCS - RAD, page 81).
Pipe clamp
Pipe Clamps, Pipe Supports
6 Pipe rest
e.g. RUK - 323
® page 79
7 T-head bolts
(to order separately) HALFEN Cantilever
e.g. HS 50/30 - M 16 x 50 - fv e.g. KON - 52/2 - fv - 700
® page 11 or 13 ® page 75
78
HALFEN FRAMING SYSTEMS
Pipe Rest RUK
Accessories
RUK - 159 00009 159
Channel slot
RUK - 168 00010 168
width > d2 2
RUK - 193 00011 193
Assembly example: RUK - 216 00012 216 75 25
140
RUK - 219 00013 219
- Pipe rest RUK
- Pipe clamp HRS - A RUK - 267 00014 267
- Cantilever KON 41/2 RUK - 273 00015 273
RUK - 318 00016 318
Design Properties
RUK - 323 00017 323
RUK - 355 00018 355
RUK - 368 00019 368
Channel slot 3
220 75 30 width < d2
RUK - 406 00020 406
Edit knobs
RUK - 419 00021 419 on-site
RUK - 508 00022 508
RUK - 521 00023 521
Support Structures
4
RUV
Pipe rest for various pipe - Ø. Designation Stock no. for Ø D L B N H
Cost efficient alternative as RUV is suitable 0317.000- [mm] [mm] [mm] [mm] [mm]
for a number of pipe sizes. Pipe rest made
RUV - K 00001 25 - 79 30 50 11 11
of plastic (Two-point-rest).
Cantilevers
RUV - M 00002 80 - 269 80 70 17 15
Material: polypropylene, restistant to RUV - G 00003 270 - 420 120 70 17 16 5
temperatures from -30 to +90°
Colour: black Pipe Clamps, Pipe Supports
B L
6
N e.g. DN 200
RUV - M
Type RUV - K for HALFEN Channels: min. 12 mm slot width
max. 52 mm channel width
Notes, Work aid
Standard to order
79
HALFEN FRAMING SYSTEMS
Pipe Clamps Type Alpha
T-head bolts, then apply to HALFEN 141 00070 141 00023 139 - 143 175 201
Channel resp. cantilever and tighten 150 00071 150 00024 148 - 152 184 210
r 17
420 00091 420 00043 418 - 422 470 520
for 50/5 50 25 28 5
hole-Ø 429 00092 429 00044 427 - 431 479 529
M 16
508 00093 508 00045 506 - 510 558 608
525 00094 525 00046 523 - 527 575 625
532 00095 532 00047 530 - 534 582 635
Notes, Work aid
7 Type
Ø D [mm]
grade
or
Stock no.: 0311.010-00074
80
HALFEN FRAMING SYSTEMS
Pipe Clamps Type Alpha, Assembly Set
Type
length
[mm] 0303.010- [mm] 0303.010- [mm] [mm]
1
Note:
When DGM (Rubber
insulation) is used, pipe rest
RUK resp. RUV is also
33,5 00042 33,5 00001 16,5 - 21,5 1 × 75
necessary.
42,5 00043 42,5 00002 25,5 - 30,5 1 × 75
48,5 00044 48,5 00003 31,5 - 36,5 1 × 120
D 00045 00004
Accessories
50 50 33 - 38 1 × 120
56 00046 56 00005
DGM 25/8
39 - 44 1 × 120
Delivery includes: 60 00047 60 00006 43 - 48 1 × 150
2
1 x Pipe clamp Alpha 64 00048 64 00007 47 - 52 1 × 150
1 x Rubber insulation DGM
77 00049 77 00008 60 - 65 1 × 180
(enclosed as cut goods)
1 x Pipe rest RUV 80 00050 80 00009 63 - 68 1 × 180
84 00051 84 00010 67 - 72 1 × 180
89 00052 89 00011 72 - 77 1 × 210
Design Properties
96 00053 96 00012 79 - 84 1 × 210
100 00054 100 00013 83 - 88 1 × 250
105 00055 105 00014 88 - 93 1 × 250 3
110 00056 110 00015 93 - 98 1 × 250
116 00057 116 00016 99 - 104 1 × 250
DGM 30/8
125 00058 125 00017 108 - 113 1 × 305
Assembly diagram 131 00059 131 00018 114 - 119 1 × 305
137 00060 137 00019 120 - 125 1 × 305
Support Structures
HCS - RAD (e.g. on HALFEN cantilever KON 52/2)
141 00061 141 00020 124 - 129 1 × 305
consisting of:
150 00062 150 00021 133 - 138 1 × 355
Rubber insul. DGM 157 00063 157 00022 140 - 145 1 × 355 4
Pipe clamp HRS - A 160 00064 160 00023 143 - 148 1 × 395
Pipe rest RUV 168 00065 168 00024 151 - 156 1 × 395
176 00066 176 00025 159 - 164 1 × 395
DGM 40/8
185 00067 185 00026 168 - 173 1 × 450
200 00068 200 00027 183 - 188 1 × 450
212 00069 212 00028 195 - 200 1 × 500
Cantilevers
218 00070 218 00029 201 - 206 1 × 500
225 00071 225 00030 208 - 213 1 × 560 5
235 00072 235 00031 218 - 223 1 × 560
267 00073 267 00032 250 - 255 1 × 650
DGM 50/8
81
HALFEN FRAMING SYSTEMS
Pipe Clamps Type Beta
Delivery includes: 105 00064 105 00017 103 - 107 149 175
3 1 x Pipe clamp 110 00065 110 00018 108 - 112 154 180
2 x Hx. head bolts 116 00066 116 00019 114 - 118 160 186
2 x Nuts 125 00067 125 00020 123 - 127 11 169 195
for 30/4 35 4 4,1
131 00068 131 00021 129 - 133 175 201
Note: M 10
Pipe clamp HRS - B 137 00069 137 00022 135 - 139 181 207
with rubber insulation DGM: 141 00070 141 00023 139 - 143 185 211
Support Structures
13
00030 248 280 4,9
D
7 Type
Ø D [mm]
Material
or
Stock no.: 0311.030-00067
82
HALFEN FRAMING SYSTEMS
Pipe Clamps Type Delta
M 10 x 40 w. v.h.
64 00030 64 00001 63 - 66 92 114 65
77 00031 77 00002 76 - 79 8,5 105 127 70
80 00032 80 00003 79 - 82 for 25/2,5 108 130 25 70 2,75 1,9
89 00033 89 00004 88 - 91 M 8 118 140 75
96 00034 96 00005 95 - 98 125 147 80
100 00035 100 00006 98 - 102 144 170 85
105 00036 105 00007 103 - 107 149 175 90
Accessories
M 12 x 40 with view hole
110 00037 110 00008 108 - 112 154 180 90
116 00038 116 00009 114 - 118 160 186 95 2
11
125 00039 125 00010 123 - 127 169 195 100
D for 30/4 35 4 4,1
131 00040 131 00011 129 - 133 M 10 175 201 100
137 00041 137 00012 135 - 139 181 207 105
141 00042 141 00013 139 - 143 185 211 105
150 00043 150 00014 148 - 152 194 220 110
Design Properties
157 00044 157 00015 155 - 159 201 227 115
160 00045 160 00016 158 - 162 208 240 125
Support Structures
Note: 225 00052 225 00023 223 - 227 273 305 160
Pipe clamp HRS-D with rubber 235 00053 235 00024 233 - 237 283 315 170
insulation DGM: ® page 85
M 16 x 50 w. v.h.
267 00054 267 00025 265 - 269
17
317 367 175 4
M 273 00055 273 00026 271 - 275 323 373 180
for 50/5 50 5 7,8
285 00056 285 00027 283 - 287 M 16 335 385 190
326 00057 326 00028 324 - 328 376 426 210
340 00058 340 00029 338 - 342 390 440 215
H
Standard to order
v
Cantilevers
D
5
Assembly diagram e.g.
a
Pipe clamp Delta
K HALFEN Channel HM 36/36
® page 34
Pipe Clamps, Pipe Supports
L
Possible
height adjustment T-head bolt HS 38/17
even after ® page 35
b
assembly
U - Washer US ..., DIN 9021 6
hole-Ø
® page 44
Type
Ø D [mm] 7
Material
or
Stock no.: 0311.050-00039
83
HALFEN FRAMING SYSTEMS
Pipe Clamps Type Gamma
Delivery includes: 137 00041 137 00012 135 - 139 181 207
1 x Pipe clamp 141 00042 141 00013 139 - 143 185 211
2 x Hex. head bolts 150 00043 150 00014 148 - 152 194 220
Design Properties
Ø2 200 00049 200 00020 198 - 202 for 40/4 248 280 40 14 17 4 4,9
212 00050 212 00021 210 - 214 M 12 260 292
218 00051 218 00022 216 - 220 266 298
h
Support Structures
Type
hole-Ø Ø D [mm]
Material
or
Stock no.: 0311.060-00039
Pipe Clamps, Pipe Supports
6
Notes, Work aid
84
HALFEN FRAMING SYSTEMS
DGM - Rubber Insulation
HALFEN Pipe clamps HRS with rubber insulation DGM Span width Rubber insulation DGM
Accessories
2 x 85
64 47 - 52
77 60 - 65 2
2 x 110
80 63 - 68
84 67 - 72
89 72 - 77 2 x 130
Assembly diagram
96 79 - 84
Pipe clamp Gamma
100 83 - 88
HRS - G (® page 84)
Design Properties
105 88 - 93
with DGM 2 x 155
110 93 - 98
(order separately)
D 116 99 - 104 3
125 108 - 113
2 x 175 DGM 30/8
131 114 - 119
137 120 - 125
2 x 190
141 124 - 129
150 133 - 138
2 x 220
Support Structures
157 140 - 145
160 143 - 148
Assembly diagram 2 x 240
168 151 - 156
Pipe clamp Delta 4
176 159 - 164
HRS - D (® page 83) 2 x 270
185 168 - 173
with DGM
200 183 - 188 2 x 295 DGM 40/8
(order separately)
212 195 - 200
2 x 310
218 201 - 206
225 208 - 213
D 2 x 345
235 218 - 223
Cantilevers
267 250 - 255
273 256 - 261
2 x 405 5
285 268 - 273 2 x 435 DGM 50/8
326 309 - 314 2 x 490
340 323 - 328 2 x 530
Pipe Clamps, Pipe Supports
Rubber insulation DGM (cut goods) [m] when ordering. [mm] 0320.000- [mm] [mm]
for HALFEN Pipe clamps
DGM 25/ 8 00001 17 - 96 17 - 96
Material:
d DGM 30/ 8 00002 100 - 157 100 - 157
7
EPDM, resistant to temp.
from - 40°C to +110° C Order example: DGM 40/ 8 00003 160 - 235 160 - 235
DGM 40/ 8, 12 m
b DGM 50/ 8 00004 267 - 532 267 - 340
or Stock no.
Standard to order 0320.000-00003, 12m DGM 60/ 8 00005 355 - 532
85
HALFEN FRAMING SYSTEMS
Sliding Pipe Supports, Spacer Clip
Framing Channels, Bolts
Material / finish:
t
200 - 235
À Pipe - Ø D [mm]
Pipe clamp Type Beta 200 200 200 100 17 8
Available diameters of Pipe clamps see
267 - 273 250 250 200 100 17 8
3 HRS-B, ® p. 82. Note: When using
285 250 250 225 125 17 8 rubber insulation DGM , larger diameters
326 250 300 250 150 17 10 are required.
H
D
340 - 355 300 300 250 150 17 10
t
5
b L
D
5 267 - 285 250 250 150 8
Material / finish:
326 250 300 150 8
L fv = Steel St 37 - 2, h.d. galvanised
b 340 - 355 300 300 200 10
A4 = Stainl. steel W1.4571/ 1.4401 (A4)
400 - 429 350 300 200 10
t 508 - 532 400 400 250 10
Pipe Clamps, Pipe Supports
(used in pairs)
Standard to order
h
25 25
Other dimensions on request. 85
86
HALFEN FRAMING SYSTEMS
Sliding Supports, Spacer Clips, Application Example
H
106,5 Da
±2 Ø 14
100
Example 1:
100 Pipe fittings on HALFEN POWERCLICK
Accessories
Framing Systems
100
200
- one range of accessories for all three 2
Fixing with 2 Spacer clips channel sizes!
HCS AHS 5/1 - fv
Stock no.
Da DN H Designation 0291. .. POWERCLICK Framing System 63
21,3 15 116 HCS HRG 4-21 - fv 040-00001 1
Design Properties
33,7 25 122
POWERCLICK Framing System 41
HCS HRG 4-33 - fv 040-00002 1
48,3 40 129 HCS HRG 4-48 - fv 040-00003 1
POWERCLICK Framing System 22
60,3 50 136 HCS HRG 4-60 - fv 040-00004 1 3
76,1 65 144 HCS HRG 4-76 - fv 040-00009 1
88,9 80 150 HCS HRG 4-89 - fv 040-00005 1
114,3 100 166 HCS HRG 4-116 - fv 040-00006 1
139,7 125 178 HCS HRG 4-141 - fv 040-00007 1
168,3 150 192 HCS HRG 4-168 - fv 040-00008 1
Support Structures
219,1 200 217,5 HCS HRG 4-219 - fv 040-00010 1 page 81
fv = h.d. galvanised
page 76 - 77
4
page 82
Cantilevers
HCS AHS see 5
above
Spacer clip, used in pairs, pre-assembled M 12 see
with 55 below
a
1 x HZS 41/22 - fv 8.8 - M12 x 50 per clip
15
Pipe Clamps, Pipe Supports
b
suitable for all channels System 41 Series 2
30 c
Max. 60 Nm
Standard to order
packing unit [pcs.]
87
HALFEN FRAMING SYSTEMS
Application Examples
Example 2:
Framing Channels, Bolts
2
Design Properties
3
Support Structures
4
ing
tspac
por
Sup
Cantilevers
Example 3:
Pipe suspension
Pipe Clamps, Pipe Supports
6
ing
tspac
por
Sup
Notes, Work aid
88
HALFEN FRAMING SYSTEMS
Pipe Weights and Support Spacing
External Pipe weigth Pipe weigth Support External Pipe weigth Pipe weigth Support External Pipe weigth Pipe weigth Support
Accessories
60,3 5,33 7,55 3,00 35 1,420 2,214
76,1 6,80 10,52 3,20 42 1,700 2,894
88,9 8,85 13,98 3,50 Drain pipe cast iron (SML, ML) 54 2,910 4,873
2
114,3 12,60 21,30 4,20 58 4,300 6,400 ca.1,50 64 3,470 6,296
139,7 16,90 30,17 4,60 78 5,900 9,900 according 70 3,800 7,219
to the £ 2,00
165,1 20,10 39,06 5,30 110 8,400 17,700 manufac- 74 4,030 7,877
135 11,800 24,500 turer´s 80 4,360 8,894
instructions
160 14,100 32,300 104 5,700 13,550
Design Properties
each length
£
Steel pipe (heating pipe) according to DIN 2448 210 23,100 54,600 of pipe 125 10,200 21,316
must 2,00 - 3,00
17,2 0,69 0,83 1,40 274 33,300 87,700 be 131 10,700 22,966
21,3 0,96 1,20 1,60 326 43,200 120,800 supported 3
at least
26,9 1,41 1,80 1,85 429 75,500 208,800 Á for pipes with normal wall thickness
twice;
33,7 2,01 2,65 2,15 532 104,300 311,800 applies
44,5 2,70 3,91 2,50 635 137,100 434,200 additionally
for each
48,3 2,95 4,41 2,60 moulded
51,0 3,12 4,77 2,70 part
Support Structures
57,0 3,90 5,96 2,80 Drain pipe PE (Geberit)
60,3 4,14 6,47 3,00 32 0,273 0,804 0,32
63,5 4,36 6,97 3,00 40 0,348 1,255 0,40 4
according manufacturer 10 x Ø
Cantilevers
127,0 12,20 23,32 4,35 125 1,817 12,271 1,25
133,0 12,80 25,07 4,40 140 2,287 15,391 1,40 5
139,7 13,50 27,12 4,50 160 3,004 20,106 1,60
152,4 16,40 32,54 4,75 200 3,830 31,457 2,00
159,0 17,10 34,76 4,80 250 6,019 49,150 2,50
168,3 18,10 36,93 4,90
Pipe Clamps, Pipe Supports
7
À Observe load capacities of pipe clamps
and reduce eventually support width.
89
HALFEN FRAMING SYSTEMS
Pipe Dimensions
Threaded pipe Seamless Insulated bright Steel Cast iron Eternit pipe PVC DIN 19 531
Framing Channels, Bolts
DIN 2440 Steel pipe Copper pipe Copper pipe Drain pipe Drain pipe DIN 19 830 PP DIN 19 560
(medium duty) DIN 2448 Wicu pipe DIN 17 440 DIN 19 530 GA DIN 19 500 ABS DIN 19 561
DIN 2441 DIN E 2460 Standard with Loro. Steel and SML Rotstrich HT
(heavy duty) heating pipe web coat plastic coated
1 Copper Insu-
pipe lation
DN Zoll Da DN Da Da Da DN DN Da DN Da DN Da DN Da
12
15
10 3/8 17,2 10 17,2 12 16
15 1/2 21,3 15 21,3 15 19 18/22
Accessories
57 63,5 64/65 50 64
65 2 1/2 76,1 65 76,1 76 70 73 70 78 70 75
3 80
76 82,5 85 70 84
80 3 88,9 80 88,9 89
94 101,6 100 100 102
100 108 100 110 100 110
100 4 114,3 100 114,3 100 116
Support Structures
113 121
127 125 125 125
4 125 133 133 125 133 125 133
137
125 5 139,7 125 139,7 125 141
150 159 159 150 159 150 160 150 160
150 6 165,1 150 168,3 150 168
177,8
175 193,7
Cantilevers
200 200
5 200 210
200 219,1 219 200 219 200 220
267
250 273 250 274 250 274
Pipe Clamps, Pipe Supports
298,5
318
300 323,9 300 326 300 326
6 350 355,6 350 355
400 406,4
400 429
500 508
500 532
Notes, Work aid
90
HALFEN FRAMING SYSTEMS
Pipe Dimensions, Selection of Pipe Clamps
10 16 17
15 20 21,5 21,5
Accessories
27 42,5 27 42,5
32 25 32 25 32 20 32 33,5 48,5 33,5 48,5 2
40 32 40 32 40 25 40 42,5 56 42,5 56
42,5 56 42,5 56
48,5 64 48,5 64 64
40 50 50 50 40 50 32 50 50 64 50 64 64
50 56 56 64 56 64 64
60 77 60 77 77
Design Properties
60 63 60 63 50 63 40 63 64 80 64 80 64 80
70 75 70 75 65 75 50 75 77 89 77 89 77 89
80 96 80 96 80 96
3
84 100 84 100 84 100
80 90 90 80 90 90 89 105 89 105 89 105
100 116 100 116 100 116
100 110 100 110 100 110 65 110 110 125 110 125 110 125
116 131 116 131 116 131
Support Structures
125 141 125 141 125 141
125 125 125 125 125 125 80 125 125 141 125 141 125 141
131 150 131 150 131 150 4
137 150 137 150 137 150
140 140 140 141 157 141 157 141 157
150 160 150 160 150 160 160 176 160 176 160 176
168 185 168 185 168 185
176 185 176 185 176 185
200 212 200 212 200 212
Cantilevers
200 200 200 200 200 200 200 212 200 212 200 212
212 225 212 225 212 225 5
218 235 218 235 218 235
250 250 267 267 267
267 285 267 285 267 285
273 285 273 285 273 285
Pipe Clamps, Pipe Supports
DN = Nominal diameter; Da = External diameter Ø D = Nominal diameter pipe clamps (® tables pages 80 - 85)
91
HALFEN FRAMING SYSTEMS
Pipe Fixing under Bridges
Regulation sketches WAS 5, 6, 13 and 15 (14, 16, 21, 25 "Fixings of conduits must consist of stainless steel material
and 26 former version): grades 1.4401 or 1.4571 acc. DIN 17 440 resp. DIN 267,
part 11."
Accessories
2
"Fixing parts and connections made of stainless steel, steel Standard catalogue of works specifications (STLK), scope of
group A4, material - no. 1.4401 or 1.4571". works LB 111, issue 5/89, generally stipulates for pipe
fixings:
"Fixing elements in stainless steel acc. to DIN 17440,
material grade 1.4571, connection components in stainless
steel acc. to DIN 267, part 11, material grade 1.4571".
Design Properties
3
Support Structures
Support structures under bridges which are not covered by WAS - regulations
Cantilevers
5
Due to the large range of HALFEN channels, T-bolts and
accessories made of stainless steel grade A4 the support
structures can be dimensioned to meet the requirements,
Pipe Clamps, Pipe Supports
92
HALFEN FRAMING SYSTEMS
Pipe Fixing under Bridges
300
Accessories
2
Section
B:B
400
HALFEN Pipe fastener according to WAS 6 HALFEN Pipe fastener according to WAS 15
Design Properties
Supply and fit _____ pieces HALFEN Pipe fastener Supply and fit _____ pieces HALFEN Pipe fastener
according to WAS 6, material Stainless steel W according to WAS 15, material Stainless steel
1.4571/ 1.4401 (A4) for DN ___. W 1.4571/ 1.4401 (A4) for DN ___. 3
Support Structures
Note: Since October
300 1997, this drawing is
no longer part of WAS
4
regulation!
The application must
as
fixed be reconsiled with
point bridge operator.
HALFEN Pipe fastener according to WAS 13 HALFEN Pipe fastener similar to WAS 16 (old)
without articulation
Cantilevers
Supply and fit _____ pieces HALFEN Pipe Supply and fit _____ pieces HALFEN Pipe 5
fastener according to WAS 13 without fastener similar to WAS 16 , material Stainless
articulation, material Stainless steel W 1.4571/ steel W 1.4571/ 1.4401 (A4) for DN ___.
1.4401 (A4) for DN ___ with/without fixed point
(WAS 14 old)
Determine dim. H on site !
as
fixed
Notes, Work aid
point
HALFEN Pipe fastener according to WAS 14 HALFEN Pipe fastener according to WAS 26 7
Supply and fit _____ pieces HALFEN Pipe Supply and fit _____ pieces HALFEN Pipe
fastener according to WAS 14 , material Stainless fastener according to WAS 26, material Stainless
steel W 1.4571/ 1.4401 (A4). for DN ___. steel W 1.4571/ 1.4401 (A4), for DN ___
with/without fixed point.
93
HALFEN FRAMING SYSTEMS
Fixing to Concrete
cut lengths
2 HALFEN cast-in channels Type HTA
and HZA are officially approved (DIBt
Berlin):
Z-21.4-34 (HTA), HALFEN Channel Typ HTA
short lengths
Z-21.4-145 (HZA toothed) and L£
Z-21.4-1691 (HZA 38/23 and 29/20 30
Design Properties
0
Dynagrip).
52 50
40 38 29 41
4
42
48
34
30
23
22
20
21
33 26,5 22 22 rolled-in 18 18 14 22
groove
cold rolled
Load range: Perm. loads acc. to German
HTA 72/49 HTA 54/33 HTA 49/30 HTA 40/25 HTA 38/17 HTA 28/15 official approval certificates, distance
Pipe Clamps, Pipe Supports
30
25
15
longitudinal direction.
HS 72/48 HS 50/30 HS 40/22 HS 38/17 HS 28/15
Order example:
7 HTA 38/17 - fv - 550
GWP 72/48 GWP 50/30 GWP 40/22 GWP 38/17 GWP 28/15 Type
Material
Length [mm] (see Catalogue B)
94
HALFEN FRAMING SYSTEMS
Fixing to Cast-In HALFEN Channels
FZ FQ F Note: HALFEN Channels are also approved for fire resistance class
Fy F90 resp. F60. Permissible loads: see official approvals.
1
a g g Fx
FZ FQ concrete strength class B 25 resp. À : B 35
Fz
ar
FZ ® a £ 150° FQ ® g £ 15° F = pull out in
ar aa
Centric or Transverse or all directions af
angled angled shear for Type HZA Ã ae
pull out
Accessories
Individual lengths Load pairs Individual channels
2
short lengths cut lengths cut lengths
Channel matching T-head bolt
FV = h.d.galvan. GV =electroplated
F1
load bearing
Type Á
Design Properties
Type with thread: F1 [kN] F1 [kN] F1 [kN] F2 [kN]
FZ 3,5 3,0 3,0 2,0
HTA 28/15 HS 28/15 M 8 - 10 FQ 3,5 3,5 3,5 3,0
5 10 4 8 3
FZ 7,0 4,5 4,5 3,0
HTA 38/17 HS 38/17 M 10 - 12 7,5 15 5 10
FQ 8,0 8,0 8,0 4,5
Support Structures
HTA 40/22 W FQ 10,0 10,0 10,0 6,0
Cantilevers
HTA 49/30 FZ 12,0 10,0 10,0 5,0
HS 50/30 M 12 - 16 - 20 15 30 13 25
HTA 50/30 W
FQ 12,0 12,0 12,0 7,0 5
FZ 22,0 (25,0) 22,0 (25,0) 22,0 (25,0) 11,0 (12,5)
HTA 52/34 W HS 50/30 M 16 - 20 À À À À 20 40 17,5 35
FQ 22,0 (25,0) 22,0 (25,0) 22,0 (25,0) 11,0 (12,5)
HTA 55/42 FZ 27,0 (32,0) 27,0 (32,0) 27,0 (32,0) 13,5 (16,0)
Pipe Clamps, Pipe Supports
W
HS 50/30 M 20 À À À À 25 50 22,5 45
HTA 54/33 FQ 27,0 (32,0) 27,0 (32,0) 27,0 (32,0) 13,5 (16,0)
HTA 72/48 W FZ 27,0 (32,0) 27,0 (32,0) 27,0 (32,0) 13,5 (16,0)
HS 72/48 M 20 - 30 À À À À 25 50 22,5 45
HTA 72/49 FQ 27,0 (32,0) 27,0 (32,0) 27,0 (32,0) 13,5 (16,0) 6
Notes, Work aid
7
À Values in brackets for using concrete strength class B 35 W = hot rolled channels, also suitable for dynamic loads.
Á HTA 55/42, HZA 38/23 and HZA 29/20 only available in h.d. galvanised. For further informations see catalogue B or official approval.
 For simultaneously loadings in multiple directions applies: FX2 + FY2 + FZ2 £ perm. F
95
HALFEN FRAMING SYSTEMS
Assembly Examples
Fig. 1 Fig. 2
Framing Channels, Bolts
1
HALFEN Channel
HALFEN Channel e.g. HTA 40/22
e.g. HTA 38/17
HALFEN Locking plate
e.g. GWP 38/17
Washer Square washer
Accessories
3
Fig. 3
Washer US
e.g.
Channel 41/83
or 41/62
Support Structures
Fig. 4 Fig. 5
96
HALFEN FRAMING SYSTEMS
Specification Texts, Parts Lists
Example 1:
Parts list:
Item pcs. Type-Finish-Length/Size 1
[mm]
1
1 HCS - 41 - RS - P - fv - LB 1200
HCS - 41 - RS - M - fv
1
(® catalogue PC41 POWERCLICK)
2
1 HCS - 41 - AS2 - P - fv - LB 1300
HCS - 41 - AS2 - M - fv
Accessories
1
(® catalogue PC41 POWERCLICK)
2
3
Design Properties
washers 10 11 Fittings:
Locking plates and
hexagon head bolts 5
3
3 KON 1 HCS - RAD - 137 - fv
Cantilevers
2
6 HCS - RAD 6
Lateral Pipe clamp
bracing fixing 1 HCS - RAD - 218 - fv
Support Structures
7
4 GWP 41/41 - gv - M 12
4
12 13 Fittings: 8
Locking plates and 4 HSK - gv - M 12 x 30
hexagon head bolts
4 KON
9
Cantilevers
1
4 US - DIN 125 - gv - M 12
7 8 9 Fittings:
Cantilevers
Column Locking plates and
hexagon head bolts 10 5
14 VA 2 GWP 41/41 - gv - M 10
Composite anchor
(dowel) incl. nut
11
and washer
2 HSK - gv - M 10 x 30
Pipe Clamps, Pipe Supports
12
2 GWP 41/41 - gv - M 12
6
13
2 HSK - gv - M 12 x 30
14
(Example,
4 dowel on-site)
Notes, Work aid
97
HALFEN FRAMING SYSTEMS
Specification Texts, Parts Lists
Example 2:
Framing Channels, Bolts
2
13 HS
T-head bolts
Accessories
4 HCS - GST 5
14 15 Fittings: Articulated brace
3 T-head bolts and 1 HCS - 41 - STR - P - fv - LB 300
washers 12 HCS - RAD 1 HCS - 41 - STR - P - fv - LB 500
Pipe clamp fixing 6 2
8 KON HCS - 41 - STR - M - fv
Cantilevers
14 HS
T-head bolts 7
Support Structures
12
14
12 HZS 41/22 - fv - M 12 x 35
Notes, Work aid
7 15
8 US - DIN 125 - gv - M 12
98
HALFEN FRAMING SYSTEMS
Specification Texts HALFEN Framing Channels and Accessories
Accessories
2
Design Properties
cut to size and fit as per specifications.
Support Structures
cut to size and fit as per specifications.
HALFEN Cantilevers
Supply and fit _____ pieces HALFEN Cantilevers
KON 36/ 2 - fv - 400 0310.070-00002
KON ___ / ___, for fixing pipes and other
construction parts.
Cantilevers
5
HALFEN Fittings
Supply and fit _____ pieces HALFEN Fittings
HVT ___ - ___, finish ___, to create different connections. HVT 36 - 7 - fv 0312.020-00007
Notes, Work aid
99
HALFEN FRAMING SYSTEMS
Specification Texts Pipe Clamp Fixing Sets, Pipe Supports
Framing Channels, Bolts
L hexagonal rod coupler SKM M 12, with T-head bolts SKM - fv - M 10 0390.000-00004
2 for existing HALFEN Channel ___/ ___ or with dowel.
Supply and fit _____ pieces HALFEN Pipe support HRG HRG - 2 - 168 - fv
_____, finish ___, as fixed support for assembly using T-
head bolts or as loose support using spacer clips and T-
head bolts, appropriate to the forces to be applied.
6
Supply and fit _____ pieces HALFEN Spacer clip Type AHS - 1 - fv 0324.000-00001
AHS _____, finish ___, as guides for pipe supports Type
7 HRG _____.
100
HALFEN FRAMING SYSTEMS
Order Form HALFEN Framing Systems
Company:
1
Accessories
2
Construction account:
Mat. / FinishÀ
Design Properties
No. Pieces Stock no. Type / Channel Length Comments Price [EUR/ piece]
Support Structures
4
Cantilevers
5
Pipe Clamps, Pipe Supports
Comments:
gv = zinc electroplated
gv 8.8 = zinc electroplated, strength grade 8.8 (bolts)
sv = pre-galvanised
fv = hot dip galvanised
7
fv 8.8 = hot dip galvanised, strength grade 8.8 (bolts)
A2 = Stainless Steel A 2 = W 1.4301
A4 = Stainless Steel A 4 = W 1.4571/ 1.4401
101
HALFEN FRAMING SYSTEMS
Index from A to Z
Bolts
2 - Hexagon head bolts 44 Lock washer SIC 45
- T-head bolts 9 - 43 Locking plates GWP 9 - 43
Bracing for cantilevers KON Z1 76
Nuts MU 44
Cantilevers KON 75 - 77
Design Properties
6
Gamma - Pipe clamps 84 WAS - Pipe fixings under bridges 93
Washer U 44
HALFEN Framing Channels Washers US 44
- Type HM, HL 8 - 42
- Type HZM und HZL, toothed 25 - 26
Notes, Work aid
102
For further information please contact: www.halfen.com
© 2009 Halfen GmbH, Germany
M - 010 - EE - 03/09 5.000 03/09
applies also to copying in extracts.