Anda di halaman 1dari 30

MT1194

SERVICE MANUAL
COLOR TELEVISION RECEIVER

ORIGINAL
MFR'S VERSION A

Design and specifications are subject to change without notice.


SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
2. AVOID AN ELECTRIC SHOCK ripheral circuit, use the designated parts and
There is a high voltage part inside. Avoid an make sure not modify the circuit.
electric shock while the electric current is Repairing except indicates causes rising of high
flowing. voltage, and it emits an X-ray from the cathode-
ray tube.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific 7. PERFORM A SAFETY CHECK AFTER
characters of incombustibility and withstand SERVICING
voltage for safety. Therefore, the part which is
replaced should be used the part which has Confirm that the screws, parts and wiring which
the same character. were removed in order to service are put in the
Especially as to the important parts for safety original positions, or whether there are the
which is indicated in the circuit diagram or the portions which are deteriorated around the
table of parts as a mark, the designated serviced places serviced or not. Check the
parts must be used. insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER (INSULATION CHECK PROCEDURE)
ASSEMBLING OR WIRING 1. Unplug the plug from the AC outlet.
There are parts which use the insulation 2. Remove the antenna terminal on TV and turn
material such as a tube or tape for safety, or on the TV.
which are assembled in the condition that 3. Insulation resistance between the cord plug
these do not contact with the printed board. terminals and the eternal exposure metal
The inside wiring is designed not to get closer [Note 2] should be more than 1M ohm by
to the pyrogenic parts and high voltage parts. using the 500V insulation resistance meter
Therefore, put these parts in the original [Note 1].
positions. 4. If the insulation resistance is less than 1M
ohm, the inspection repair should be
5. TAKE CARE TO DEAL WITH THE required.
CATHODE-RAY TUBE [Note 1]
In the condition that an explosion-proof cathode- If you have not the 500V insulation
ray tube is set in this equipment, safety is resistance meter, use a Tester.
secured against implosion. However, when
[Note 2]
removing it or serving from backward, it is
External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to
deal with it.

HOW TO ORDER PARTS


Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.

IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.

A1-1
CONTENTS

SERVICING NOTICES ON CHECKING .......................................................................................................... A1-1


HOW TO ORDER PARTS ............................................................................................................................... A1-1
IMPORTANT .................................................................................................................................................... A1-1
CONTENTS ..................................................................................................................................................... A2-1
GENERAL SPECIFICATIONS ........................................................................................................................ A3-1~A3-4
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP ................................................................................................................. B1-1
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................................... B2-1, B2-2
SERVICE MODE LIST ..................................................................................................................................... C-1
CONFIRMATION OF HOURS USED .............................................................................................................. C-1
WHEN REPLACING EEPROM (MEMORY) IC ............................................................................................... C-2
ELECTRICAL ADJUSTMENTS ....................................................................................................................... D-1~D-4
BLOCK DIAGRAM ........................................................................................................................................... E-1, E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT .................................................................................................................................................... F-1~F-4
SCHEMATIC DIAGRAMS
MICON/CHROMA/TUNER ........................................................................................................................... G-1, G-2
TV POWER .................................................................................................................................................. G-3, G-4
DEFLECTION/CRT ...................................................................................................................................... G-5, G-6
SOUND/AV .................................................................................................................................................. G-7, G-8
WAVEFORMS .................................................................................................................................................. H-1, H-2
MECHANICAL EXPLODED VIEW ................................................................................................................... I-1
MECHANICAL REPLACEMENT PARTS LIST ............................................................................................... J1-1
ELECTRICAL REPLACEMENT PARTS LIST ................................................................................................. J2-1, J2-2

A2-1
GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 19 inch / 480.0mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.45G/0.18G
Color System NTSC
Speaker 1Speaker
Position Bottom
Size 3 Inch
Impedance 8 ohm
Sound Output MAX 1.5 W
10%(Typical) 1.0 W
NTSC3.58+4.43 /PAL60Hz No
G-2 T u n in g Broadcasting System US System M
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage A - I, J - W, W+1 - W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.50MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
G-3 Power Power Source AC 120V AC 60Hz
DC
Power Consumption at AC
73 W at AC 120 V 60 Hz
Stand by (at AC) 5 W at AC 120 V 60 Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
Safety Circuit Yes
IC Protector(Micro Fuse) No
G-4 Regulation Safety UL
Radiation FCC
X-Radiation DHHS
G-5 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-6 Operating Humidity Less than 80% RH
G-7 On Screen Menu Yes
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
CH Set Up Yes
TV/CATV Yes
Auto CH Memory Yes
Add/ Delete Yes
Language Yes
V-chip Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Volume Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Back Light No
Stereo,Audio Output,SAP No
Video Yes

A3-1
GENERAL SPECIFICATIONS
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Sleep Timer Yes
Sound Mute Yes
V-chip Rating Yes
G-8 OSD Language English French Spanish

G-9 Clock and Sleep Timer Max Time 120 Min


Timer Step 10 Min
On/Off Timer Program(On Timer / Off Timer) No
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec
G-10 Remote Unit RC-DW
Control Glow in Dark Remocon No
Format NEC
Custom Code 86-05 h
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No
G-11 Features Auto Degauss Yes
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip Yes
Type USA,ORION Type
BBE No
Auto Search No
CH Allocation No
SAP No

A3-2
GENERAL SPECIFICATIONS
Channel Lock No
Just Clock Function No
Game Position No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Lines
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
Stable Sound No
Energy Star No
Power On Memory No
Favorite CH No
G-12 Accessories Owner's Manual Language English / Spanish
w/Guarantee Card Yes
Remote Control Unit Yes
Rod Antenna No
Poles
Terminal
Loop Antenna No
Terminal
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card No
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
Important Safeguard No
Dew/AHC Caution Sheet No
AC Plug Adapter No
Quick Set-up Sheet No
Battery No
UM size x pcs
OEM Brand No
AC Cord No
AV Cord (2Pin-1Pin) No
Registration Card No
PTB Sheet No
300 ohm to 75 ohm Antenna Adapter No
G-13 Interface Switch Front Power Yes
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
Rear AC/DC No
TV/CATV Selector No
Degauss No
Main Power SW No
Indicator Power No
Stand-by No
On Timer No
Terminals Front Video Input RCA
Audio Input RCA x 1
Other Terminal No
Rear Video Input(Rear1) No
Video Input(Rear2) No
Audio Input(Rear1) No
Audio Input(Rear2) No
Video Output No
Audio Output No
Euro Scart No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
AC Outlet No
G-14 Set Size Approx. W x D x H (mm) 488 x 465 x 416
G-15 Weight Net (Approx.) 17.5kg ( 38.6 lbs)

A3-3
GENERAL SPECIFICATIONS
Gross (Approx.) 20.0kg ( 44.1lbs)
G-16 Carton Master Carton No
Content ---- Sets
Material -- /--
Dimensions W x D x H(mm) -- x -- x --
Description of Origin No
Gift Box Yes
Material Double/Brown
Dimensions W x D x H(mm) 546 x 526 x 472
Design As per Buyer's
Description of Origin Yes
Drop Test Natural Dropping At 1 Corner / 3 Edges / 6
Surfaces
Height (cm) 46
Container Stuffing 436 Sets/40' container
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
Cabinet Rear PS 94V0 DECABROM
PCB Non-Halogen Demand No
Eyelet Demand No
G-18 Environment Pb Free Lead-free Solder No
Other No
Cd Free No

A3-4
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
After turning the power off there might still be a potential
* voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
Do not use pliers to loosen or tighten the Anode Cap
* terminal, this may cause the spring to be damaged.
amount of alcohol. (Refer to Fig. 1-3.)

REMOVAL
1. Follow the steps as follows to discharge the Anode Cap. Location of Anode Cap
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of
a flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated screwdriver,
touch the support of the Anode with the tip of the
screwdriver.
A cracking noise will be heard as the voltage is discharged.

Fig. 1-3
GND on the CRT
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver CRT
Support
Alligator Clip

GND on the CRT Fig. 1-4


Fig. 1-1

2. Flip up the sides of the Rubber Cap in the direction of the 4. Insert one end of the Anode Support into the anode button,
arrow and remove one side of the support. then the other as shown in Fig. 1-5.
(Refer to Fig. 1-2.)

Rubber Cap

CRT Support
CRT Support Fig. 1-5
Fig. 1-2
5. Confirm that the Support is securely connected.
6. Put on the Rubber Cap without moving any parts.

B1-1
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
REMOVAL
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Some ICs on the PCB are affixed with glue, so be
Package IC to protect other parts from any damage. careful not to break or damage the foil of each IC
(Refer to Fig. 2-1.) leads or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within Blower type IC
10 mm distance from IC leads. desoldering
machine

Masking Tape IC
(Cotton Tape)

Tweezers

Fig. 2-1
IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)
4. Peel off the Masking Tape.
NOTE
Do not add the rotating and the back and forth 5. Absorb the solder left on the pattern using the Braided
directions force on the IC, until IC can move back and Shield Wire. (Refer to Fig. 2-4.)
forth easily after desoldering the IC leads completely. NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine

Braided Shield Wire

Soldering Iron

IC
IC pattern Fig. 2-4
Fig. 2-2

B2-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-
1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 2-8.)
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)
Thin-tip Soldering Iron IC

Soldering Iron

Fig. 2-8

5. Finally, confirm the soldering status on four sides of the


Solder temporarily Solder temporarily
IC using a magnifying glass.
Confirm that no abnormality is found on the soldering
Fig. 2-5 position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.
2. Supply the solder from the upper position of IC leads NOTE
sliding to the lower position of the IC leads.
When the IC leads are bent during soldering and/or
(Refer to Fig. 2-6.)
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.

Solder Soldering Iron

IC Supply soldering
from upper position
to lower position

Fig. 2-6

3. Absorb the solder left on the lead using the Braided


Shield Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.

Soldering Iron
IC

Braided Shield Wire

Fig. 2-7

B2-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.

Set Key Remocon Key Operations


VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
Initialization of the factory.
VOL. (-) MIN 1 NOTE: Do not use this for the normal servicing.
If you set a factory initialization, the memories are reser such as the clock
setting, the cheannel setting, the POWER ON total hours, and PLAY/REC
total hours.

POWER ON total hours is displayed on the screen.


Refer to the "CONFIRMATION OF HOURS USED".
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".

Writing of EEPROM initial data.


VOL. (-) MIN 8
NOTE: Do not use this for the normal servicing.

Display of the Adjustment MENU on the screen.


VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

CONFIRMATION OF HOURS USED


POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".
1. Set the VOLUME to minimum. ADDRESS DATA

2. Press both VOL. DOWN button on the set and Channel


button (6) on the remote control for more than 2 second.
INIT 00 50 Initial setting content of MEMORY IC.
3. After the confirmation of using hours, turn off the power.
CRT ON 0010 POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
FIG. 1 + (16 x tens digit value)
+ (ones digit value)

C-1
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.

INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F

00 50 04 EB 47 07 B3 24 79 31 00 00 05 10 D5 00 07

Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. While holding down VOLUME button on front cabinet, press key 6 on remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 1.

ADDRESS DATA

INIT 00 50
CRT ON 0010

Fig. 1
3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.

After the data input, set to the initializing of shipping.


9. Turn POWER on.
10. While holding down VOLUME button on front cabinet, press key 1 on remote control for more than 2 seconds.
11. After the finishing of the initializing of shipping, the unit will turn off automatically.

The unit will now have the correct DATA for the new MEMORY IC.

C-2
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS
ADJUSTMENTS 2-1: CUT OFF
Read and perform these adjustments when repairing the 1. Adjust the unit to the following settings.
circuits or replacing electrical parts or PCB assemblies. R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
CAUTION B.BIAS=64, BRI.CENT=105, CONT.MAX=65.
2. Place the set with Aging Test for more than 15 minutes.
• Use an isolation transformer when performing any service 3. Activate the adjustment mode display of Fig. 1-1 and
on this chassis. press the channel button (01) on the remote control to
• Before removing the anode cap, discharge electricity select "CUT OFF".
because it contains high voltage. 4. Adjust the Screen Volume until a dim raster is obtained.
• When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire 2-2: FOCUS
back in its original position. 1. Receive the monoscope pattern.
• When you exchange IC and Transistor for a heat sink, 2. Turn the Focus Volume fully counterclockwise once.
apply the silicon grease (YG6260M) on the contract 3. Adjust the Focus Volume until picture is distinct.
section of the heat sink, Before applying new silicon
grease, remove all the old silicon grease. (Old grease 2-3: WHITE BALANCE
may cause damages to the IC and Transistor.)
NOTE: Adjust after performing CUT OFF adjustment.
Prepare the following measurement tools for electrical 1. Place the set with Aging Test for more than 10 minutes.
adjustments. 2. Receive the white 100% signal from the Pattern
1. Synchro Scope Generator.
2. Digital Voltmeter 3. Using the adjustment control, set the brightness and
3. Pattern Generator contrast to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
On-Screen Display Adjustment press the channel button (10) on the remote control to
1. In the condition of NO indication on the screen. select "R.BIAS".
Press the VOL. DOWN button on the set and the 5. Using the VOL. UP/DOWN button on the remote control,
Channel button (9) on the remote control for more than adjust the R.BIAS.
1 second to appear the adjustment mode on the screen 6. Press the CH. UP/DOWN button on the remote control to
as shown in Fig. 1-1. select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".
7. Using the VOL. UP/DOWN button on the remote control,
adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS.
TV 8. Perform the above adjustments 6 and 7 until the white
color is looked like a white.
2-4: SUB TINT/SUB COLOR
1. Receive the color bar pattern.
2. Connect the oscilloscope to TP023.
00 OSD H 28 3. Activate the adjustment mode display of Fig. 1-1 and
Fig. 1-1 press the channel button (22) on the remote control to
select "TINT".
2. Use the Channel UP/DOWN button or Channel button 4. Press the VOL. UP/DOWN button on the remote control
(0-9) on the remote control to select the options shown until the section "A" becomes as straight line
in Fig. 1-2. (Refer to Fig. 2-1)
3. Press the MENU button on the remote control to end 5. Connect the oscilloscope to TP022.
the adjustments. 6. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (19) on the remote control to
select "COL.CENT".
NO. FUNCTION NO. FUNCTION
7. Press the VOL. UP/DOWN button on the remote control
00 OSD H 16 CONTRAST CENT
01 CUT OFF 17 CONTRAST MAX until the red color level is adjusted to 110 ±10% of the
04 H.VCO 18 CONTRAST MIN white level. (Refer to Fig. 2-2)
05 H.PHASE 19 COLOR CENT 8. Receive the color bar pattern. (Audio Video Input)
06 V.SIZE 20 COLOR MAX 9. Press the TV/AV button on the remote control to set to
07 V.SHIFT 21 COLOR MIN the AV mode. Then perform the above adjustments 2~7
08 R.DRIVE 22 TINT
09 B.DRIVE 23 SHARPNESS
10 R.BIAS 24 FM LEVEL
11 G.BIAS 25 LEVEL
12 B.BIAS 26 SEPARATION 1
13 BRIGHT CENT 27 SEPARATION 2
14 BRIGHT MAX 28 TEST MONO
15 BRIGHT MIN 29 TEST STEREO
Fig. 1-2

D-1
ELECTRICAL ADJUSTMENTS
2-8: OSD HORIZONTAL
1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote
control until the difference of A and B becomes
minimum. (Refer to Fig. 2-3)

TV
"A"

Fig. 2-1

00 OSD H 28

A B
Fig. 2-3

2-9: SUB BRIGHTNESS


1. Receive an 70dB monoscope pattern.
2. Using the adjustment control, set the brightness and
contrast to normal position.
Red 110% 3. Activate the adjustment mode display of Fig. 1-1 and
Fig. 2-2 press the channel button (13) on the remote control to
select "BRI.CENT".
4. Press the VOL. UP/DOWN button on the remote control
2-5: HORIZONTAL PHASE
until the white 10% is starting to be visible.
1. Receive the monoscope pattern. 5. Press the TV/AV button on the remote to set to the
2. Using the adjustment control, set the brightness and AV mode. Then perform the above adjustment 2~4.
contrast to normal position.
2-10: SUB CONTRAST
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (05) on the remote control to 1. Receive an 70dB the color bar pattern.
select "H.PHAS". 2. Activate the adjustment mode display of Fig. 1-1
4. Press the VOL. UP/DOWN button on the remote press the channel button (17) on the remote control
control until the SHIFT quantity of the OVER SCAN on to select "CONT.MAX".
right and left becomes minimum. 3. Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "60".
2-6: VERTICAL SIZE 4. Press the TV/AV button on the remote to set to the
NOTE: Adjust after performing adjustments in section 2-5 AV mode. Then perform the above adjustment 2, 3.
1. Receive the crosshatch signal from the Pattern
2-11: Confirmation of Fixed Value (Step No.)
Generator.
2. Activate the adjustment mode display of Fig. 1-1 and Please check if the fixed values of the each adjustment
press the channel button (06) on the remote control to items are set correctly referring below.
select "V.SIZE". NO. FUNCTION RF AV
3. Press the VOL. UP/DOWN button on the remote control 04 H VCO 04 04
until the SHIFT quantity of the OVER SCAN on upside 14 BRIGHT MAX 150 150
and downside becomes 10 ± 2%. 15 BRIGHT MIN 45 45
4. Receive a broadcast and check if the picture is normal. 16 CONT CENT 45 45
18 CONT MIN 15 15
2-7: VERTICAL SHIFT 20 COLOR MAX 74 74
NOTE: Adjust after performing adjustments in section 2-6 21 COLOR MIN 00 00
23 SHARPNESS 45 45
1. Receive the crosshatch signal from the Pattern 24 FE LEVEL 00 00
Generator. 25 LEVEL 00 00
2. Activate the adjustment mode display of Fig. 1-1 26 SEPARATION 1 00 00
and press the channel button (07) on the remote 27 SEPARATION 2 00 00
28 TEST MONO 00 00
control to select "V.SFT".
29 TEST STEREO 00 00
3. Press the VOL. UP/DOWN button on the remote
control until the horizontal line becomes fit to the
notch of the shadow mask.

D-2
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE

NOTE Adjust after performing adjustments in section 3-2.


1. Receive the crosshatch pattern from the color bar
1. Turn the unit on and let it warm up for at least 30
generator.
minutes before performing the following adjustments.
2. Combine red and blue of the 3 color crosshatch pattern
2. Place the CRT surface facing east or west to reduce the
on the center of the screen by adjusting the pair of
terrestrial magnetism.
4 pole magnets.
3. Turn ON the unit and demagnetize with a Degauss Coil.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted 3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar 1. Adjust the differences around the screen by moving
generator. the deflection yoke upward/downward and right/left.
3. Slide the deflection yoke until it touches the funnel (Refer to Fig. 3-2-a)
side of the CRT. 2. Insert three wedges between the deflection yoke
4. Adjust center of screen to green, with red and blue on the and
sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 3-2-b)
pattern to the crosshatch pattern.
RGB RGB
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets. R
7. Combine red/blue (magenta) and green by adjusting the G
pair of 6 pole magnets. B
8. Adjust the crosshatch pattern to change to white R
by repeating steps 6 and 7. G
B
3-2: PURITY
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE
Fig. 3-2-a
Adjust after performing adjustments in section 3-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide. WEDGE WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the WEDGE
screen, then tighten the fixing screw.
DEFLECTION YOKE WEDGE POSITION
DEFLECTION YOKE SCREW
Fig. 3-2-b
MAGNET SCREW

PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1

D-3
ELECTRICAL ADJUSTMENTS

4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

CD803

CP
80
3B
CRT PCB

CP806

R8

R8
03
FB401 CP803A TU001

07
01
J8
1 TP022
40 TP023
CP

2B
80
CP801

CP
CD801
CR

CRT
T

CRT

CD802
L503

CP502

S501B
CP802A

CD501
AC IC

S501A

CD101A

SPEAKER

CD101B

MAIN PCB

D-4
BLOCK DIAGRAM

TU001

10 11 12 13 17
CH. DOWN
IC1001 AN7511
VOL. DOWN
2 6
21 20 34 SPEAKER
SOUND AMP
CH. UP SP1001
4 IC 8
66 ATT
VOL. UP RGB Proc.2
73 OSD SW Q801
67 CONTRAST BRIGHTNESS 50 RED OUT
RGB OUTPUT
Chroma Proc.
68 Stage DRIVE 51
ACC/C-BPF Q802
CUT OFF
OS101 I/O APC/KILLER 52
HV BLK GREEN OUT
IIC RGB Proc.1 MCU TINT/DEMO
70
1 TIM RGB MATRIX CLK Q607
INT COLOR CONT Q803
78 PWM H-CTL
BLUE OUT
AD Ver.Proc.
OSD Hor.Proc.
Ver SYNC SEP 46
SYNC SEPA/Hor. VCO
Ver.COUNT DOWN 45
ROM
Hor.COUNT DOWN
IIC BUS V RAMP
RAM
AFC-1/H COINCIDENT
DECODER Q402
AFC-2 H PHASE
J703 Video Proc. H. DRIVE
C-TRAP/Y DELAY
2 Q401
SHARPNESS
BLACK VCXO H. OUTPUT
J702
STRETCHY MUTE
2
56 58 57 27 26 37 38 16 3 9 7
MICON/CHROMA IC B G R
X601
Q505 IC101 OEC7091B CRT
3.579545MHz Heater
P. FAIL V801
V-OUT IC 4 F 8
IC501 IC401 LA78040N-E
T502 PS2561AL1-1-V(W) Q507 5 6
FEED BACK MEMORY IC PUMP UP
4 FEED BACK SDA SCL IC199
16 SW
S-24C02BFJ-TB -
AMP
8 Q502 +
L503
TH501

BUFFER DEGAUSS COIL VCC


13
7 1 2 6 5 DY
6
Q501
POWER AMP FB401
D501~D504 9
RECTIFIER 1 F
2 S
L501 10 HV
2 4
3
1 3

F501

AC IN
E-1 E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE
CRITIQUE , VOIR AU VERSO.

FOR SERVICE INFORMATION ABOUT CRITICAL


R429
W066 R403 INFORMATIONPOUR SERVICE DES PIECE

D404
C406 ATTENTION

COMPONENTS, SEE INSIDE BACK COVER.


C435
W003

HEATER
C442

W021

GND

AFC
D408

R404
W064

ABL

CAUTION
D411

180V
D405
C403
D410
CD803A

W008

8V
CP803A

TU001

12V

25V
T401

COL
C434 CP4

W847
01
D412

C440

C43

R421
C443 FB401

7
R408 W845
W801
Q402
W062 W001
R427

W848
W011

D509
HS402

R409
01 Q401 R542
R446 S4 HS501
H D409
R448 R503 D506
C410

R520
R506
Q501

D512
CP601
R449
R504

D001
W010

C511
Q502
D406 W004

R508
C514_1

W819
C446 C510_1

C509
R522
1

R417
40

D516
W007 IC R511_1

R424 C516 D508


W009

D513
W025

R447
C414 B501 C526_1
C417_1

R509
T502
W039
C521
C418

W038
C422_1 R514

R501
W016

B504
R410

R416
R415

R423

R407
W050
W070

R002

R422

IC501
D403

D502

C506_1
D501
C517
C515
W018

C502
C508_1
D510

C503
C427

D505
W015
W006

L001 C402
TP401
W048
W049

D503
Q602
R001 C518

D504
C617_1

W817
R445 CP502
R62

R515

D507
D511
W831 Q601 9_1
C606_1 Q603
R505

W046

D528
D517

R512
2
W067
17

40
W836

R608 D514 R5

R
R603

D515
W034

W019
R502

R518
W832

C103_1
L101

TH501_1
R528
D521
D606

Q606
C519
Q507 TCD460A

R513
W024
W073

W040

C601_1 CD803B
L801
W023

L501
R519 CP803B
C623_1
W020 J801

R804_1
X601
R119 R605
R604 R130
W058
W057

D602

D522 CP806 C505


R116 R8
03
R123 _2

C8
R601

R500
C632_1

19
W013 R105 R802
C621_1 IC1001 CP801_2 S501B
W056
R8

W816 R106
07

C610_1 C628_1 W017 R538


W055
_2

W805 TP022

C801
W803 R806
W053 TP023
W851

CD501
C630_1 C1005_1 S501A
W051
W052

W068
C624

R621
D604
CD802A

W061 R607 4A125VOR250V


CP802A

Q803_1
R1001

R805_2

Q801_1
R611

W069
R620

R614 W032 Q802_1


W045
W044
W043

D603

R613 W014
R617

CP802B
R615 W030
FH502 F501 FH501
CD802B
W028

C633_1
TP024

Q607
R616

W029

W807
R112
R113
R143

W027
W026
C123_1
R110

OS101
R109
W042

CD101A
TMD604A
W041

C118_1
J703 J702
SW101 SW102 SW103 SW104 SW105
W060

CD101B

F-1 F-2
F-3
TMD604A
C501
TCD460A

R813
C808_2
R809
R816
C810_2
R814

R507
R101

R811
R815
C809_2

C407_1 C513_2

R419 C1004
R420

R1008
R418
SOLDER SIDE

C1009 C1001
R1003

R1005

R1004

C620 R126
C001 C007_1 C004 R115
R405
R004 R003
PRINTED CIRCUIT BOARDS

R128

R108

R125
R127
MAIN/CRT (CHIP MOUNTED PARTS)

R618
C629_1
64

R129
R627

C639
1
R609

IC R107
R610

10 C626_1
1
41

C627_1
C102
R704

C101
25

C602 C622
C105 R606
IC199

R102
C107 C104 C603 R602
R120 C609_1
R701 R703 R702

C108 C641
R104
C113
C611 R103 C604_1 C616
C605
C615

C607
C608
F-4
A B C D E F G H

0 0 0 0 MICON/CHROMA/TUNER SCHEMATIC DIAGRAM


1 2 3 4
(MAIN PCB)

VSS
E1

E2
E0
S-24C02BFJ-TB
8 8

MEMORY IC

50V 10 YK
C633_1
IC199
H.CTL

0.001 B
Q607

MODE

C641
VCC

SDA
SCL
KTC3198

W805
R621 6.0 5.0

47K 1/4W
8 7 6 5
4.9 0 4.8 4.8

R617
220 1/4W

1/2W
5.6

R620
R618

1K

P.CON+5V
P.CON+5V
22K

H_OUT

H_CTL
3 FROM/TO DEFLECTION/CRT

H_SYNC
C118_1 R608

B.OUT
ABCL
H_CTL

G.OUT

R.OUT
7 CLAMP 7
C632_1 2 1K 1/4W
6.3V 470 YK R110 10K 1/4W

1K 1/4W 1N4002-PAN
C101
V_OUT

D606
R109 10K 1/4W 10V 470 YK
0.01 B

10V 470 YK
100 1/4W

100 1/4W

100 1/4W
GND

C630_1

12K
R610
V_FEEDBACK
AT+5V

B
ABCL

0.01 B
R105

C626_1
10K 1/4W
1/4W

1 TF
4.7K

C629_1

50V 1 KA

C627_1
0.01 B

C624
0.01
H_OUT

R611
R123

C628_1
P.CON+5V

R615

R614

R613
X-RAY

R609

120K
10K 1/4W

R616
1 CNVSS 41 NC SDA C623_1 R.OUT

R108

100
2 XIN 42 HVCO F/B R130

R107
SCL

100
G.OUT

R106

1/4W
4.7K

R627
6

10K
3 XOUT 43 AFC FILTER 5 7 50V 2.2 KA
10K 1/4W NC NC NC B.OUT
4 TEST1 44 DEF GND 4.8 0 4.8 0.7 2.3 2.2 2.3 8.0 0 8.0 2.0 1.0 0 3.4 3.7 0
0 0 0 0 0 0 4.8 0 H_SYNC
5 VSS 45 FBP IN 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
6 8.6 7.9 8V REG 6
R119 4.8 R607
6 MCU VCC 46 H OUT Q606

65

40
KTC3203_Y
7 TEST0 47 DEF VCC 22K 1/4W 4.7 100 1/4W 8.5
2.4
AFT MCU GND 4

66

39
8 FILT 48 NC R112 Ver.Proc. 11.3 UNREG+12V
9 HLT 49 HI VCC 4.9 3.6 FROM TV POWER
2.2K 1/4W KEY1 IIC BUS PGB OUTPUT Stage Hor.Proc. Ver SYNC SEP V_OUT

67

38
10 VHOLD 50 R OUT R113 DECODER DRIVE SYNC SEPA/Hor.VCO
Ver.COUNT DOWN 2.6 R606
4.9 CUT-OFF Hor.COUNT DOWN POWER_FAIL
11 CVIN 51 G OUT 2.2K 1/4W KEY2 SDA/SCL AFC-1/H COINCIDENT V RAMP V_FEEDBACK

68

37
ROM HV BLK
12 RESET IN 52 B OUT POWER_ON R116 OSD AFC-2 H PHASE 22K UNREG+12V
4.9 RAM 0
GND

69

36
13 MCU RESET OUT 53 ACL C621_1
R115
2.2K 1/4W 3.2 +B
14 Y SW OUT 54 NC 4.8 C622
REMOCON

70

35
22K 16V 47 YK
15 V/C GND 55 PROTECT
I/O 3.5 1 F
0
16 3.58 XTAL 56 SDA NC AUDIO_OUT C620

71

34
RGB Proc.2
17 C-APC 57 H_CTL OSD SW RGB Proc.1 0.7
5 4.9 1 0.01 B FROM/TO SOUND/AV 5
72 RGB MATRIX

33
18 MCU5.7V REG OUT 58 SCL NC CONTRAST NC
P-ON CONT Power Manage. BRIGHTNESS COLOR CONT 2.8
19 NC 59 NC 4.9 IIC D604 AUDIO_MUTE
AUDIO_MUTE D603
73

32
MCU RESET NC
20 CVBS IN3 60 NC VIDEO_IN2
2.8 TIM 8.7 1SS133 R605
21 AUDIO IN3 61 NC X-RAY MTZJ8.2B
CCD AUDIO_IN2
74

31
R125 INT Chroma Proc.
22 V/C VCC 62 DEGAUSS_H Vldeo Proc. P.CON+5V 220 1/2W
R127 4.8 ACC/C-BPF 1.9 AUDIO_OUT
47K IIC_OFF C-TRAP/YDELAY
75

30
23 MCU TEST 63 STANDBY_H PWM APC/KILLER NC TUNER+5V P.CON+5V
SHARPNESS
1K CLK CONT TINT/DEMO 2.2
24 CVBS IN2 64 VOLUME 0 AD MCU BLACK STRETCH GND
CPU core 5V REG
76

29
NC CLK Y MUTE NC 4.9
25 AUDIO IN2 65 NC Q602
0 5.5 R604
26 CVBS IN1 66 AFT KTC3203_Y
77

28
NC LPF
27 AUDIO IN1 67 KEY1 6bB AMP ATT 100 1/4W 5.5
4.8 2.2 C608 7.2 R629_1
POWER_FAIL AUDIO_IN2
78

27
28 5.7V REG OUT 68 KEY2
VCO 1.9 1 F
29 C(Y/C) IN 69 POWER_ON R129 0 XO 7.2 22 3W
C607
79

26
4 30 Y(Y/C) IN 70 REMOCON VIDEO_IN2 C617_1 5.5 4
47K 4.9 VCXO 0 C001
31 VREG VCC 71 AV2 1 F 5V REG
80

25

19

18
NC NC 10V 100 YK Q603 4.9
32 FSC OUT 72 AV1 1 NC 0.01 F
KTC3203_Y
33 MONITOR OUT 73 AUDIO_MUTE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
0 0 4.9 4.9 0 4.9 0 1.0 1.9 0.3 2.7 4.9 4.9 2.7 0 3.3 2.8 5.5 0 2.5 2.2 4.9 0 1.9 2 NC
34 AUDIO ATT OUT 74 X-RAY MICON/CHROMA IC

100BT3R537

0.022 B 22P CH 3.579545MHz


NC NC L001
0.001 B
NC
470P B 1K 0.01 B

IC101

0.1 F
TUNER+5V
C108

C602

X601
35 AUDIO ATT FILTER 75 IIC_OFF
C104

R602
OEC7091B

100
C102 3.3uH 0305
C611

36 NC 76 ON_TIMER AT+5V
4
1

37 V RAMP F/B 77 SYNC 0.01 B

C601_1

50V 1 KA
R102

C603
38 V RAMP OUT 78 POWER FAIL
R120

6.3V 100 YK
220P B

470

5 NC

C606_1
0305
6.3V 470 YK

39 V RAMP CAP 79 X-RAY_TEST C615


C103_1

TU_VIDEO
1K

C604_1
L101

40 8.7V REG OUT 80 EXT_MUTE 6


560P B

1 F NC
C616
R104

C113
3.3uH

1M

TU_AUDIO
C105
R103

C107

C609_1 1 F
3 3

C605

1 F
0.01 B 7 NC

MTZJ8.2B
D602
W816

C610_1
W836

8 NC

1/4W
R601
16V 47 YK
8.2K 9 NC
TEST POINT
R004
SCL
10
CP601
100
AT+5V

R003 173979-6
REMOCON

SDA
KEY1

11
KEY2

POWER_ON

100 NC 6
12 AFT NC 5
IIC_OFF
R143 IIC_OFF 4
F
C639

R128 13 TU_AUDIO SDA


SDA 3
50V 10 YK

0.01

10 1/4W

B
C007_1
SCL
C123_1

2 560 SCL 2 2
R126 R101 14

0.022
5.5 NC
GND 1
R002 R001
2.7K 560 R603 +B
4.9 8.8 15
15K 1/2W 15K 1/2W

F
POWER_ON

EVQ21505R

120 1/2W
VOL DOWN
EVQ21505R

EVQ21505R

EVQ21505R
EVQ21505R

SW105
CH DOWN

C004
16 NC

0.022
SW101

SW103

SW104

5V REG
VOL UP
SW102
CH UP
KSM-713SY
4.9
4.8

TU001
0

Q601
ENG36A01GY TU_VIDEO
KTC3203_Y 17
OS101
GND 3
B+ 2
1

W801 D001
Vout

20

21
MTZJ33B
PCB010
TMD604

R.SIGNAL
1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION:LES PIECES REPAREES PAR UN ETANT G.SIGNAL 1
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST DANGEREUSES AN POINT DE VUE SECURITE B.SIGNAL
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES DEFLECTION SIGNAL
TUNER VIDEO SIGNAL
A B C D E F G H
G-1 G-2
A B C D E F G H

TV POWER SCHEMATIC DIAGRAM


(MAIN PCB)
8 8

CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,


REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501)
FUSE.
4A 125V
ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES
D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 4A 125V (F501).

TO SOUND/AV

GND
R517
D505
SOUND+B
7 21DQ09N 1.5 1W 7

16V 1000 YK
C518

C519
500V470P B

SOUND_GND

TO DEFLECTION/CRT
D510

+-10%
+B

2.7M 1/2W
DEGAUSS COIL
PS106R

R500
L503 UNREG+12V
8R200031 CP502
A1561WV2-2P
C517

160V 100 MHE


1
1

2KV 820P RR
6 2
2

C521
TH501_1
R501

B59203-S1060-B14

1.2M 1/2W 1.2M 1/2W


3.3 5W

1N4005-EIC

R511_1
1N4005-EIC
D501

D502
GND

R522
ECQUL

MTZJ5.6B
1N4005-EIC
1.5M 1/2W

1/4W
500V 0.001 B

D521
1N4005-EIC
TO MICON/CHROMA/TUNER

500V 0.001

200V 220 YK
C503

D503
3 4

R528
C526_1
D504

T502
C505

C502
275V 0.33

R538

MTZJ18B
5 4A 125V 8129109S 5

6.8K
+B

D509
1 2 W832
AC120V_60Hz
S501A

F501 POWER_FAIL
CD501
4A125V
0R414903
BLACK R514 D516 R504 R505
COIL,LINE FILTER 1.7 10.0
4A125V 8 11
FH501 FH502 L501 1N4937-PAN 100 1/4W 1K 1/4W

50V 10 YK
0.22 1W
BLADE
WIDE

EYF-52BCY SS11V-10062-CH
S501B

WHITE EYF-52BCY 0

C516
NC 7 12

144.0 132.3 B504 D513


6 13 UNREG+12V
W5RH3.5X5X1.0

W5RH3.5X5X1.0

16V 1000 YK
21DQ09N

C515
0
B501

NC 5 14

10.3 0
4 15 GND
4 4

1/4W
6.6 11.3
W819

R502
2KV 820P RR

C506_1 3
C514_1

16
D517

1K
250V 0.0033 KY 144.0 10.3
2 17 NC
D MTZJ4.7B
R508 C509
G 4.8

1SS133
D512
220 1/2W 0.047 TF 18 NC
1SS133

S
D508

0.1 POWER AMP


Q501
12K 1/4W

100 1/4W

2SK3563(ORION_Q)
R520

R503
220 1/4W

C511
R509
2.7K 1/4W

3 50V 1 KA 3
R506

MTZJ3.6B
BUFFER

0.001 B
1SS133

C513_2
MTZJ18B

D515

D507
Q502
KTC3198 4.8
D506
0.47 1W
R542

0.1
B

HS501
C501

0
0.0082

763WSAA013

120K 1/2W
1/4W
1SS133
D511

R513

R515
2.2K
C508_1 9.5
6.0

1SS133

1SS133
D514

D522
250V 0.0022 KY FEED BACK FEED BACK
C510_1 IC501 5.5 SWITCHING
PS2561AL1-1-V(W) Q507
KTC3198
0.039 TF
2 11.5 10.5 2
R512 R519
4

680 1/4W 1K 1/4W


3

R507
0.1 9.5

27
CAUTION: DIGITAL TRANSISTOR
MTZJ5.6B
D528

5.6K +-1%
R518
PCB010
TMD604

1 1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES IS NON POLAR ONE.

A B C D E F G H
G-3 G-4
A B C D E F G H

FROM MICON/CHROMA/TUNER DEFLECTION/CRT SCHEMATIC DIAGRAM(MAIN PCB) CP802A B2013H02-5P


GND
GND 1
CD802

1
CP802B B2013H02-5P
GND
GND
CLAMP CLAMP
CLAMP CLAMP 2 2 CLAMP
G.OUT G.OUT
8 G.OUT G.OUT 3 3 G.OUT 8
R.OUT R.OUT
R.OUT R.OUT 4 4 R.OUT
B.OUT B.OUT
B.OUT B.OUT 5 5 B.OUT
V-OUT IC IC401 LA78040N-E CD803
CP803A B2013H02-3P CP803B B2013H02-3P
HEATER HEATER
THERMAL HEATER 1 1 HEATER
PROTECTION GND GND
GND 2 2 GND
PUMP 180V 180V
UP AMP 180V 3 3 180V

R811

R814
R809

4.7K
1 2 3 4 5 6 7

4.7K

4.7K
L801
CP801_2

100uH
3.5 25.0 2.0 0 12.0 25.0 3.5
003P-2100

YK
35V 100
C414
1
7 CD801 7
8
R423 CU012401 1
12
D403
100 1/4W 2
13 3.2 3.2 3.2
1N4002-PAN
V801
A48AKH13X04 2.7 2.7 2.7

100V 0.1 TF
128.0

390 1/2W
C422_1

R410
9
126.0 120.5 BLUE OUT
10 RED OUT GREEN OUT
R424 R418 R420 R Q803_1
8 Q801_1 Q802_1
G 2SC4217 2SC4217 2SC4217

25V 470 YK
15K 1/4W
6

680
R419
6.8K 1/4W 33K 4.7K R415
B

25V 10 KA

C418
11

R417
680 1/2W

1 1/2W
5 7 1

390P CH
C417_1

R816
R813

R815

330
390P CH

390P CH
C808_2

330

330
R416

C809_2

C810_2
50V 10 YK
TO DY

3.9 1/2W

C427
HS401

R422
1/2W
R407
6 763WSAA013 6

3.9
CP401
5 14 15 16
A1561WV2-A5P
4
3 TP022 TP024 TP023

100V 22 YK
C434
R429 NC 2
1
3.9 1W

10K +-1%

2.7K 1/4W

2.7K 1/4W
MTZJ5.1B

1/4W
D411
D412

R408

1N4937-PAN

2.7K
R803_2

12K 2W

12K 2W

12K 2W
R805_2

R807_2
FROM/TO MICON//CHROMA/TUNER

R806
R802

R804_1
R409
W831
5 X-RAY 5
56K +-1%

W847

PMS
C437

250V 0.33
T401
9 STP-03Q24

330P B
C801
3 4
NC 2
470 1/2W
R446

1 6
GND
H.DRIVE
V_FEEDBACK
Q402 10
4 V_OUT 2SC1627_Y 4
ABCL 27.0 11 FB401 BSC23-N0148
500V 680P B

H_OUT 130.0 COL


C410

0.3
W845

W848 1 HV
1.25KV 0.0072 PHE

H_SYNC 0 FOCUS
TF

50V 22 YK

130.0
C440

CP806
R405

C446

H.OUTPUT SCREEN
1K

C443
100V 0.1

FOCUS
100 1/4W

0 Q401 132.5 VIDEO F


FROM TV POWER 0 6
R427

TT2140LS-YBC11

B
SCREEN

C819
S

2KV 0.001
132.5 B+
GND 2
TP401 HS402 GND 0
48.0 11
763WSA0017 AFC
9
R402 HEA ABL 4.3 96.4
7.0 7
W817 10 TER
+B

9
0

8
3 1 1W GND 3
R403 8

7
E12 101.6
22K 1/4W NC 4 GND 0

F
6
8
C406 25.0 E25 0
3

1
NC

5
E8
500V 270P B 5 0 0

4
3
6.4 99.6 J801
C407_1

0.001 B

ISMS01S
1 1W
R404
MTZJ6.2B

1N4937-PAN
D404

D405

R447
D406
UNREG+12V PCB110
150 2W 1N4002-PAN
TCD460
1N4937-PAN

2 2
D410
1N4002-PAN
D409

160V 100 MHE


C402

ATTENTION:LES
250V 10 YK

PIECES REPAREES PAR UN ETANT NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
C442

R449 DANGEREUSES AN POINT DE VUE SECURITE OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
680 1/2W
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
R448
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
680 1/2W R445
IS NON POLAR ONE.
CAUTION:SINCE THESE PARTS MARKED BY ARE
TF

150K 1/4W
35V 470 YK

CRITICAL FOR SAFETY,USE ONES


1N4002-PAN
220K 1/4W

DESCRIBED IN PARTS LIST ONLY


C435

100V 0.1

D408
C403

1 R.SIGNAL 1
R421

PCB010
G.SIGNAL
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
TMD604 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST B.SIGNAL
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
DEFLECTION SIGNAL
A B C D E F G H
G-5 G-6
A B C D E F G H

SOUND/AV SCHEMATIC DIAGRAM


8
(MAIN PCB) 8

RCA JACK WHITE


J703
TO MICON/CHROMA/TUNER (FRONT)
AV1-09D-4 ACCESSORY
19
R703

E
7 AUDIO 2 7
AUDIO_IN2 A_IN

1
820
20
R704

E
VIDEO 2 V_IN
VIDEO_IN2

1
10

R701

R702

47K
68
RCA JACK YELLOW
TM101
J702
RC-DW110
AV1-09D-3
GND

6 6

5 5

W807
4 4

18
FROM TV POWER

CD101A SPEAKER
SOUND_GND
CH012002
1 1
SOUND+B 2 2
CD101B
CH012003 SP1001
GND S08F21
8.2 3.5 0 3.4
8 OHM
5 6 7 8

AN7511
SOUND AMP IC
+ -
3 3

IC1001
FROM MICON/CHROMA/TUNER
4 3 2 1
R1001 5.1 0 0.3 3.9
AUDIO_MUTE
47K 1/4W

R1003
P.CON+5V
68K

50V 10 YK
C1005_1
C1009
R1004

1 F
R1005
100K

270K
W803

2 2

0.0027 B
C1004
W851

17
C1001 R1008
AUDIO_OUT
0.1 B 39K PCB010
TMD604

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED


WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION:LES PIECES REPAREES PAR UN ETANT TUNER VIDEO SIGNAL
1 DANGEREUSES AN POINT DE VUE SECURITE 1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES AUDIO SIGNAL
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-7 G-8
WAVEFORMS
MICON/CHROMA/TUNER

1 0.5V 2ms/div 6 1V 20µs/div 11 200V 20µs/div

2 20V 20µs/div 7 1V 20µs/div 12 10V 5ms/div

DEFLECTION/CRT

3 200mV 20µs/div 8 0.5V 5ms/div 13 10V 5ms/div

4 0.5V 5ms/div 9 20V 20µs/div 14 50V 20µs/div

5 1V 20µs/div 10 2V 20µs/div 15 50V 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.

H-1
WAVEFORMS

16 50V 20µs/div

SOUND/AV

17 0.5V 1ms/div

18 1V 1ms/div

19 200mV 500µs/div

20 500mV 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.

H-2
MECHANICAL EXPLODED VIEW
104
201

201

201

206
J801
106
102

201
105 202
PCB110
(CRT PCB ASS'Y) 107
L503
206 FB401
TU001
205
V801
206
204

203

203 103
101D

101C

203 PCB010
(MAIN PCB ASS'Y)

203

103
203

101B
SP1001

101

101A

I-1
MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION
101 7A701A126A FRONT CABI ASS'Y
101A 701WPJC696 CABINET,FRONT
101B 713WPAA124 GUIDE,REMOCON
101C 735WPBB125 BUTTON,FRAME
101D 735WPAA610 BUTTON,BASE

102 A3R107Q740 CABINET,BACK ASS'Y or


702WPAA476 CABINET,BACK or
702WPAA504 CABINET,BACK or
702WPAA680 CABINET,BACK
103 735WPAA647 HOLDER,SPEAKER
104 722A08A148 SHEET,RATING
105 741WUA0019 SPRING,EARTH
106 8994201000 HOLDER,CRT WIRE
107 899HV3T000 HOLDER,ANODE WIRE
108 800WQ0A024 FELT,SHEET 5x80 T=0.5

201 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16


202 8109I30804 SCREW,TAP TITE(B) WH7 3x8
203 8110630A04 SCREW,TAP TITE(P) BRAZIER 3x10
204 8107630804 SCREW,TAP TITE(S) BRAZIER 3x8
205 8109I30604 SCREW,TAP TITE(B) WH7 3x6
206 8121F50B84 SCREW,TAP TITE(P) FAI20 FLAT 5x28

--- A3R006V975 INSTRUCTION BOOK KIT


--- 791WHAA017 LAMIFILM BAG
--- 792WHAA050 PACKAGE,TOP
--- 792WHAA051 PACKAGE,BOTTOM
--- 793WCDC312 GIFT,BOX
--- J3R00601A INSTRUCION BOOK
--- J3R00602A WARRANTY SHEET
--- JB5U0200 POLYBAG,INSTRUCTION

J1-1
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION
RESISTORS DIODES
R402 R3T181010J R,METAL OXIDE 1 OHM 1W or D511 D1VT001330 DIODE,SILICON 1SS133T-77
R3K581010J R,METAL OXIDE 1 OHM 1W ! D512 D1VT001330 DIODE,SILICON 1SS133T-77
R404 R63581010J R,FUSE 1 OHM 1W D513 D28T21DQN9 DIODE SCHOTTKY 21DQ09N-TA2B1
! R408 R4X5T6103F R,METAL 10K OHM 1/6W or D514 D1VT001330 DIODE,SILICON 1SS133T-77
R4T5T6103F R,METAL 10K OHM 1/6W D515 D1VT001330 DIODE,SILICON 1SS133T-77
! R409 R4X5T6563F R,METAL 56K OHM 1/6W or ! D516 D2MXN49370 DIODE,FAST RECOVERY 1N4937-PAN or
R4T5T6563F R,METAL 56K 0HM 1/6W D2WXN49370 DIODE SILICON 1N4937
! R429 R635813R9J R,FUSE 3.9 OHM 1W D517 D97U04R71B DIODE,ZENER MTZJ4.7B T-77
! R447 R3T28A151J R,METAL OXIDE 150 OHM 2W or D521 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
R3K58A151J R,METAL OXIDE 150 OHM 2W D522 D1VT001330 DIODE,SILICON 1SS133T-77
! R500 R0G3K2275K RC 2.7M OHM 1/2W D528 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
! R501 R5T2CD3R3J R,CEMENT 3.3 OHM 5W or D602 D97U08R21B DIODE,ZENER MTZJ8.2B T-77
R5X2CD3R3J R,CEMENT 3.3 OHM 5W D603 D1VT001330 DIODE,SILICON 1SS133T-77
! R508 R002T2221J RC 220 OHM 1/2W D604 D97U08R21B DIODE,ZENER MTZJ8.2B T-77
! R509 R002T4221J RC 220 OHM 1/4W D606 D2MXN40020 DIODE,FAST RECOVERY 1N4002-PAN or
! R514 R63581R22J R,FUSE 0.22 OHM 1W D2WT011E10 DIODE SILICON 11E1-EIC
! R515 R002T2124J RC 120K OHM 1/2W ICS
! R517 R3T1811R5J R,METAL OXIDE 1.5 OHM 1W IC101 I56F07091B IC OEC7091B
! R518 R4X5T6562F R,METAL 5.6K OHM 1/6W or IC199 A3R101Q015 INIT DATA
R4T5T6562F R,METAL 5.6K OHM 1/6W ! IC401 I03TD804N0 IC LA78040N-E
! R519 R002T4102J RC 1K OHM 1/4W ! IC501 000220002W PHOTO COUPLER PS2561AL1-1-V(W)
! R538 R002T2155J RC 1.5M OHM 1/2W IC1001 I01DP75110 IC AN7511
! R542 R3T181R47J R,METAL OXIDE 0.47 OHM 1W or TRANSISTORS
R3K581R47J R,METAL OXIDE 0.47 OHM 1W ! Q401 TD3Q021400 TRANSISTOR SILICON TT2140LS-YBC11
! R629 R3T28B220J R,METAL OXIDE 22 OHM 3W or ! Q402 TC5T01627Y TRANSISTOR SILICON 2SC1627_Y(TPE2)
R3K58B220J R,METAL OXIDE 22 OHM 3W ! Q501 T25F035630 FET 2SK3563(ORION_Q)
! R803 R3T28A123J R,METAL OXIDE 12K OHM 2W ! Q502 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! R805 R3T28A123J R,METAL OXIDE 12K OHM 2W Q507 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! R807 R3T28A123J R,METAL OXIDE 12K OHM 2W Q601 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
CAPACITORS Q602 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
C402 E5EZFB101M CE 100 UF 160V Q603 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
! C403 E02LT4471M CE 470 UF 35V Q606 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
! C414 E02LU4101M CE 100 UF 35V Q607 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! C418 E02LT3471M CE 470 UF 25V ! Q801 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
! C434 E02LU8220M CE 22 UF 100V ! Q802 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
C437 P4J7F3334J CMPP 0.33 UF 250V PMS ! Q803 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
! C443 P4G8FJ722H CMPP 0.0072UF 1.25KV PHE COILS &TRANSFORMERS
! C446 E02LU5220M CE 22 UF 50V L001 02167F3R3J COIL 3.3 UH
! C503 C0JTB0513K CC 0.001 UF 500V B L101 02167F3R3J COIL 3.3 UH
! C505 P2122B334M CMP 0.33 UF 275V ECQUL ! L501 029X000417 COIL,LINE FILTER SS11V-10062-CH
! C506 CC3LE0ML3M CC 0.0033UF 250V ! L503 028R200031 COIL,DEGAUSS 8R200031
! C508 CC3LE0MH3M CC 0.0022UF 250V L801 021673101K COIL 100 UH
C514 C0PLRR7W2K CC 820 PF 2KV RR T401 045011001L TRANS,HORIZONTAL DRIVE STP-03Q24
C517 C0PLRR7W2K CC 820 PF 2KV RR ! T502 048129109S TRANSFORMER,SWITCHING 8129109S
! C519 E02LT2102M CE 1000 UF 16V JACKS
C521 E5EZFB101M CE 100 UF 160V J702 060Q401077 RCA JACK AV1-09D-3
! C526 E02LFC221M CE 220 UF 200V J703 060Q401076 RCA JACK AV1-09D-4
! C801 CHGTB04L2K CC 330 PF 50V B ! J801 066F120018 SOCKET,CATHODE RAY TUBE ISMS01S
C819 C0JBB0713K CC 0.001 UF 2KV B SWITCHES
D I O D ES SW101 0504101T34 SWITCH,TACT EVQ21505R
D001 D97U03301B DIODE,ZENER MTZJ33B T-77 SW102 0504101T34 SWITCH,TACT EVQ21505R
D403 D2MXN40020 DIODE,FAST RECOVERY 1N4002-PAN or SW103 0504101T34 SWITCH,TACT EVQ21505R
D2WT011E10 DIODE SILICON 11E1-EIC SW104 0504101T34 SWITCH,TACT EVQ21505R
D404 D97U06R21B DIODE,ZENER MTZJ6.2B T-77 SW105 0504101T34 SWITCH,TACT EVQ21505R
! D405 D2MXN49370 DIODE,FAST RECOVERY 1N4937-PAN or P.C.BOARD ASSEMBLIES
D2WTAU02A0 DIODE SILICON AU02A-EIC PCB010 A3R107Q010 PCB ASS'Y TMD604A
D406 D2MXN40020 DIODE,FAST RECOVERY 1N4002-PAN or PCB110 A3R101Q110 PCB ASS'Y TCD460A
D2WT011E10 DIODE SILICON 11E1-EIC MISCELLANEOUS
D408 D2MXN40020 DIODE,FAST RECOVERY 1N4002-PAN or B501 024HT03553 CORE,BEADS W5RH3.5X5X1.0
D2WT011E10 DIODE SILICON 11E1-EIC B504 024HT03553 CORE,BEADS W5RH3.5X5X1.0
D409 D2MXN40020 DIODE,FAST RECOVERY 1N4002-PAN or ! CD501 1209414909 CORD AC BUSH 9414909 or
D2WT011E10 DIODE SILICON 11E1-EIC 120R414903 CORD AC BUSH 0R414903
! D410 D2MXN49370 DIODE,FAST RECOVERY 1N4937-PAN or CD801 06CU012401 CORD CONNECTOR CU012401
D2WTAU02A0 DIODE SILICON AU02A-EIC CD802 WCL6848038 FLAT CABLE AWM2468 AWG26 5C GRAY 480MM
! D411 D2MXN49370 DIODE,FAST RECOVERY 1N4937-PAN or ! CP401 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
D2WTAU02A0 DIODE SILICON AU02A-EIC ! CP502 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
! D412 D97U05R11B DIODE,ZENER MTZJ5.1B T-77 CP601 0694260139 CONNECTOR PCB SIDE 173979-6
! D501 D2WXN40050 DIODE SILICON 1N4005-EIC CP801 069D01001A CONNECTOR PCB SIDE 003P-2100
! D502 D2WXN40050 DIODE SILICON 1N4005-EIC CD101A 06CH012002 CORD CONNECTOR CH012002
! D503 D2WXN40050 DIODE SILICON 1N4005-EIC CD101B 06CH012003 CORD CONNECTOR CH012003
! D504 D2WXN40050 DIODE SILICON 1N4005-EIC CP802A 067U005049 WIRE HOLDER B2013H02-5P
! D505 D28T21DQN9 DIODE SCHOTTKY 21DQ09N-TA2B1 CP802B 067U005049 WIRE HOLDER B2013H02-5P
D506 D97U01801B DIODE,ZENER MTZJ18B T-77 CP803A 067U003029 WIRE HOLDER B2013H02-3P
D507 D97U03R61B DIODE,ZENER MTZJ3.6B T-77 CP803B 067U003029 WIRE HOLDER B2013H02-3P
D508 D1VT001330 DIODE,SILICON 1SS133T-77 ! F501 081PC04005 FUSE 51MS040L
! D509 D97U01801B DIODE,ZENER MTZJ18B T-77 ! FB401 043219018Y TRANSFORMER,FLYBACK BSC23-N0148
! D510 D2WXRU2AM0 DIODE SILICON RU2AM-EIC FH501 06710T0009 HOLDER,FUSE EYF-52BCY

J2-1
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION
MISCELLANEOUS
FH502 06710T0009 HOLDER,FUSE EYF-52BCY
OS101 077Q000025 REMOTE RECEIVER KSM-713SY
SP1001 070Y132018 SPEAKER S08F21
! TH501 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14
TM101 076N0DW110 TRANSMITTER RC-DW110
TU001 0163100011 RF UNIT ENG36A01GY or
0163300005 RF UNIT 115-V-K015AR_B
! V801 098Q200490 CRT W/DY A48AKH13X04
X601 100BT3R537 CRYSTAL HC-49U

RESISTOR
RC................... CARBON RESISTOR

CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR

J2-2
SPEC.NO. M3R1-07Q
O/R NO. W443056

Anda mungkin juga menyukai