Catatan
Notes
Criteria 5.4A.1.1 Assessor guide: observe that – Assessor guide: confirm that –
Weld requirements are determined in accordance with All appropriate specifications and drawings are obtained The weld requirements can be identified. The weld specifications
job specifications. in accordance with work site procedures. can be identified. The location and size of welds can be identified.
Kriteria 5.4A.1.2 Pedoman penilai: amati bahwa – Pedoman penilai: pastikan bahwa –
Material dibersihkan dan disiapkan dengan menggunakan Material yang akan dilas dibersihkan dan disiapkan Penyiapan material yang dibutuhkan sebelum pengelasan dapat
perkakas dan teknik yang sesuai berdasarkan prosedur dengan menggunakan perkakas dan teknik yang sesuai diidentifikasi. Perkakas dan teknik yang tepat untuk penyiapan
operasi standar. berdasarkan prosedur operasi standar. material untuk pengelasan dapat diidentifikasi.
Criteria 5.4A.1.2 Assessor guide: observe that – Assessor guide: confirm that –
Material is cleaned and prepared using appropriate tools The materials to be welded are cleaned and prepared The materials preparation required prior to welding can be
and techniques in accordance with standard operating using appropriate tools and techniques in accordance identified. The tools and techniques appropriate to the
procedures. with standard operating procedures. preparation of materials to be welded can be identified.
Australian National Training Authority Issue date – October 2001 54149351.doc Page 1 of 5
Metal and Engineering Industry Competency Standards – Standar Kompetensi Industri Teknik dan Logam
Criteria 5.4A.2.1 Assessor guide: observe that – Assessor guide: confirm that –
Welding equipment including cylinders and regulators The welding equipment is correctly assembled and set up The procedures for assembling and setting up oxy acetylene/fuel
are assembled and set up safely and correctly in in accordance with standard operating procedures. gas welding equipment can be given. The safety precautions to
accordance with standard operating procedures. be taken when assembling and setting up oxy acetylene/fuel gas
welding equipment can be identified.
Elemen 5.4A.3 Menentukan peralatan las, pengesetan dan alat bantu yang digunakan
Elemen 5.4A.3 Select welding equipment, settings and consumables
Kriteria 5.4A.3.1 Pedoman penilai: amati bahwa – Pedoman penilai: pastikan bahwa –
Ujung-ujung las, pengesetan dan barang-barang yang Oksigen dan asetilen diset berdasarkan prosedur operasi Pengesetan yang tepat untuk suatu tugas yang diberikan dan
digunakan ditentukan sesuai persyaratan pekerjaan, standar. ujung las yang dipilih dan barang-barang yang digunakan dapat
prosedur pengelasan, berdasarkan prosedur operasi diidentifikasi. Penggunaan berbagai macam batang pengisi dan
standar. terak dapat ditunjukkan. Batang pengisi dan terak yang tepat
untuk suatu tugas yang diberikan dapat diidentifikasi. Alasan
untuk pemilihan ujung las, batang pengisi dan terak dapat
diberikan.
Criteria 5.4A.3.1 Assessor guide: observe that – Assessor guide: confirm that –
Welding tips, settings and consumables selected against The appropriate oxygen and acetylene (or appropriate The appropriate settings for the given task and the selected
job requirements, welding procedures, in accordance fuel gas) settings are set in accordance with standard welding tips and consumables can be identified. The application
with standard operating procedures. operating procedures. of a variety of filler rods and fluxes can be given. The
appropriate filler rod and flux for the given task can be
identified. The reasons for selecting the chosen welding tip, filler
rod and flux can be given.
Criteria 5.4A.4.1 Assessor guide: observe that – Assessor guide: confirm that –
Weld undertaken safely and to prescribed procedure. That all welds are performed safely and in accordance The hazards associated with welding processes can be identified.
with standard operating procedures. Appropriate personal protection equipment and its function can
be identified. The appropriate ventilation/extraction
Australian National Training Authority Issue date – October 2001 54149351.doc Page 2 of 5
Metal and Engineering Industry Competency Standards – Standar Kompetensi Industri Teknik dan Logam
requirements can be identified.
Kriteria 5.4A.4.2 Pedoman penilai: amati bahwa – Pedoman penilai: pastikan bahwa –
Hasil las dibersihkan sesuai dengan prosedur operasi Seluruh hasil las dibersihkan menurut spesifikasi dan Persyaratan pembersihan hasil las dapat diidentifikasi.
standar. sesuai dengan prosedur operasi standar. Perkakas/peralatan yang tepat untuk membersihkan mesin las
dapat diidentifikasi.
Criteria 5.4A.4.2 Assessor guide: observe that – Assessor guide: confirm that –
Welds cleaned in accordance with standard operating All welds are cleaned in accordance with specifications The weld cleaning requirements can be identified. The
procedure. and standard operating procedures. appropriate tools/equipment for cleaning welds can be identified.
Range statement
Routine welding in this unit is intended to apply in a manufacturing or maintenance environment where welding is not required to meet National Standard/ISO or equivalent codes
and/or licensing requirements. Welding to National Standard/ISO is covered by Unit 5.21A (Weld using oxyacetylene welding process (OAW) fuel gas welding). The person would work
autonomously or within a team environment using predetermined standards of quality, safety, work and welding procedures. Materials welded may include low carbon steel, cast
iron, etc. Preparation of materials would be minimal and include preheating, setting up jigs, fixtures, clamps etc. Setting up may include the correct connection of hoses, blowpipes,
regulators etc. and correct settings of gas mixtures. This unit should not be selected when Unit 5.21A (Weld using oxyacetylene welding process (OAW) fuel gas welding) has been chosen.
Pedoman bukti
Konteks penilaian Kondisi penilaian
Unit ini dimungkinkan untuk dinilai pada pekerjaan, tidak pada pekerjaan atau Peserta akan diperlengkapi dengan: – Semua peralatan, perlengkapan, material dan dokumentasi yang
kombinasi antara keduanya. Kompetensi-kompetensi yang meliputi unit ini akan diperlukan. Peserta akan diijinkan mengacu pada dokumen-dokumen berikut: – Prosedur yang relevan
diperagakan secara individual atau sebagai bagian dari suatu kelompok. dengan tempat kerja. – Spesifikasi yang relevan dengan produk dan pembuatan. – Codes, standar, buku
Lingkungan penilaian jangan sampai merugikan peserta. pedoman, dan referensi material yang relevan. Peserta akan diperlukan untuk: – Menjawab pertanyaan
yang diberikan oleh Assessor secara lisan atau menggunakan metode komunikasi lainnya. – Mengenal
rekan kerja yang dapat membantu mengumpulkan bukti yang kompeten. Memberikan bukti-bukti yang
dapat menunjukkan kemampuan seseorang pada off the job training yang berkaitan dengan unit ini.
Penilai harus yakin bahwa peserta dapat menguasai dan konsisten melakukan seluruh elemen dalam
unit ini sesuai spesifikasi kriteria, termasuk pengetahuan yang diperlukan.
Australian National Training Authority Issue date – October 2001 54149351.doc Page 3 of 5
Metal and Engineering Industry Competency Standards – Standar Kompetensi Industri Teknik dan Logam
Evidence guide
Assessment context Assessment conditions
This unit may be assessed on the job, off the job or a combination of both on and The candidate will be provided with: – All tools, equipment, materials and documentation required.
off the job. The competencies covered by this unit would be demonstrated by an The candidate will be permitted to refer to the following documents: – Any relevant workplace
individual working alone or as part of a team. The assessment environment procedures. – Any relevant product and manufacturing specifications. – Any relevant codes, standards,
should not disadvantage the candidate. manuals and reference materials. The candidate will be required to: – Orally, or by other methods of
communication, answer questions put by the assessor. – Identify colleagues who can be approached for
the collection of competency evidence where appropriate. – Present evidence of credit for any off-job
training related to this unit. Assessors must be satisfied that the candidate can competently and
consistently perform all elements of the unit as specified by the criteria, including required knowledge.
Australian National Training Authority Issue date – October 2001 54149351.doc Page 4 of 5
Metal and Engineering Industry Competency Standards – Standar Kompetensi Industri Teknik dan Logam
Australian National Training Authority Issue date – October 2001 54149351.doc Page 5 of 5