M
Q
1 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : SK1912OR,SK1912OR01
STEP 1 :
a . Place the Glass Panel A (or B) inside of the Cage as
Glass Panel A (or B)
shown .
b . Place Tabs onto the top edge of the Glass Panels and Lock Screw
match the holes on the Tabs onto Mounting Holes on
the top edge of the Cage .
Tab
c . Using screwdriver , thread Lock Screws into Mounting
Holes and hand tighten until snug to secure Glass
Panels .
Cage
Cage
STEP 2:
a . Install correct bulbs referring to fixture markings and / or labels for maximum wattage .
2 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : SK1912OR,SK1912OR01
STEP 3 :
a . Locate the Nipple on the bottom center of the Socket
Assembly through the center hole on the bottom of the
Cage with Glass Panels. Secure them with the Hex
Coupling and tighten until snug.
b . Screw the Short Nipple into the Hex Coupling. Pass the
Cap over the Short Nipple and secure with the Finial. Hand
tighten until snug.
Socket Assembly
Nipple
Cage with
Glass Panels
Hex Coupling
Short Nipple
Cap
Finial
STEP 4 :
a . Secure the Crossbar onto the Outlet Box with Outlet Box
Screws . Tighten until snug . Outlet Box
Crossbar
Outlet Box
Screw
3 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : SK1912OR,SK1912OR01
STEP 5:
* Pliers is required on this step .
a . Thread one Hex Nut onto top end of the Nipple .
b . Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of Lock Washer
the Crossbar . Crossbar
Hex Nut
c . Us ing pliers , thread the Hex Nut against the c rossbar
and hand tighten until snug .
d . Thread another Hex Nut onto the bottom end of the
Nipple . Nipple
Hex Nut
STEP 6 :
a . Adjust the Fixture Chain to your desired length by
removing the links if needed .
* Please note that depends on chain material thickness ,
you might be required to use chain pliers to spread links Nipple
open .
b . Pull the supply wires through the Fixture Chain alternating Hex Nut
links . And then pull the wires through the following
Lock Washer
components in turn :
Canopy Lock Ring , Ceiling Canopy , Canopy Chain Loop,
Lock Washer , and Nipple . Canopy Chain Loop
c . Place Lock Washer over the end of the Nipple and thread
the Canopy Chain Loop onto the end of the Nipple .
d . Using plier , thread the Hex Nut against the Canopy Chain
Ceiling
Loop and tighten until snug . Canopy
e . Attach one end of the Fixture Chain onto the Fixture Loop
and attach the another end of the chain onto the Canopy
Chain Loop .
f . Refer to Step 7 - Wire Connections to connect wires . Fixture Chain
g . Push the Ceiling Canopy upward over the Outlet Box .
h . Thread the Canopy Lock Ring onto the Canopy Chain Loop
and tighten until snug to secure the Ceiling Canopy .
Canopy Lock Ring
Fixture Loop
STEP 7 :
* Use Wire Connectors ( not supplied ) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires .
a . Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b . Connect the House White ( or Ribbed ) Wire to the
BLACK ( OR RED ) WIRE BLACK OR SMOOTH
Fixture Supply Wire ( White or Ribbed Side ) .
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE FROM FIXTURE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet GROUND WIRE GROUND WIRE
Box . FROM HOUSE FROM FIXTURE
Your installation is completed now . Restore electricity . Retain this sheet for future reference .
4 OF 4