6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445 STYLE NUMBER: FQ1914MK, FQ1914AW
www . quoizel . com
3 pcs C
C Hex Nut
Short Nipple 1 pc D
D
E Lock Washer 2 pcs E
I Ceiling Canopy 1 pc H
J Tab 4 pcs
I
K Lock Screw 4 pcs
L Cap 1 pc J
M Hex Coupling 1 pc Q
K
N Nipple 1 pc
L
O Finial 1 pc
M
P Socket Assembly 1 pc
N
Q Shade 1 pc
R Cage 1 pc
R
O
1 OF 5
PREPARATION STYLE NUMBER: FQ1914MK, FQ1914AW
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (4) 60W candelabra base bulbs .
● Helpful Tools (not included): Wire strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a. Place the Shade inside of the Cage as shown. Shade
b. Place Tabs onto the top edge of the Shade and line up Mounting Hole Tab
holes on them and Mounting Holes on the Cage.
c. Using screwdriver, thread Lock Screws into Mounting
Holes and hand-tighten until snug to make sure the Lock
Tabs engage the Shade. Screw
Shade
Cage
Cage
STEP 2 :
a. Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
STEP 3:
a. Remove the Hex Nuts from the Nipple on the bottom
center of the Junction Box.
b. Pass the center hole on the bottom of the Cage over the Fixture Hood
end of the Nipple and secure with one removed Hex
Nut. Tighten until snug.
c. Screw the another removed Hex Nut back to the Nipple
and adjust to proper location for the rest components.
d. Place the Cap over the end of the Nipple and secure Junction Box
with the Hex Coupling. Hand-tighten until snug with
Nipple
pliers.
Hex Nut
Hex Nut
Cap
Hex Coupling
2 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ1914MK, FQ1914AW
STEP 4:
a. Screw the Hex Nut onto the Nipple. Then thread the
Nipple into the Hex Coupling underside of the Cage. By Cage
using pliers, thread the Hex Nut against the Hex
Coupling. Hang-tighten until snug.
b. Thread the Finial onto the end of the Nipple. Hang- Hex Coupling
tighten until snug. Hex Nut
Nipple
Finial
STEP 5:
a. Secure the Crossbar onto the Outlet Box with Outlet
Box Screws. Tighten until snug. Outlet Box
Crossbar
Outlet Box
Screw
STEP 6:
a. Thread one Hex Nut onto top end of the Short Nipple.
b. Place one Lock Washer over the top end of the Short
Nipple and then thread the Short Nipple into the center
lock hole of the Crossbar. Lock Washer
c. Using pliers, thread the Hex Nut against the Crossbar Crossbar
and hand-tighten until snug. Hex Nut
Short Nipple
STEP 7:
a. Thread another Hex Nut onto the end of the Short
Nipple.
b. Place the Lock Washer over the end of the Short Nipple
and then thread the Canopy Chain Loop onto the end of
the Short Nipple. Short Nipple
c. Using pliers, thread the Hex Nut against the Canopy
Chain Loop and hand-tighten until snug.
Hex Nut
Lock Washer
3 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ1914MK, FQ1914AW
STEP 8:
a. Push the Ceiling Canopy upward over the Outlet Box. Outlet Box
Thread the Canopy Lock Ring onto the Canopy Chain
Loop and tighten until snug to secure the Ceiling
Canopy.
Ceiling Canopy
STEP 9:
a. Adjust the Fixture Chain to your desired length by
removing the links if needed. You may need to use
pliers to open the chain links. If so, put a cloth over the Canopy Chain Loop
chain to protect the finish from the pliers.
b. Attach one end of the Fixture Chain onto the Canopy
Chain Loop and then attach the other end of the Fixture
Chain onto the Fixture Loop on the top of the fixture.
Fixture Chain
Supply Wires
Fixture Loop
STEP 10:
a. Pull the Supply Wires up through the Fixture Chain
alternating links. Push the wires up through the Canopy
Chain Loop into the outlet box. Canopy Chain Loop
Fixture Chain
Supply Wires
4 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ1914MK, FQ1914AW
STEP 11:
Outlet Box
a. Un-thread the Canopy Lock Ring and slide Canopy
Lock Ring and Ceiling Canopy down the Fixture Chain.
b. Push all slack fixture wire through Canopy Chain Loop
into Outlet Box. Trim excess fixture wire leaving a
minimum of 6 in. Hanging out of the Outlet Box.
c. Refer to STEP 12 to connect the wires. Canopy Chain Loop
d. Re-attach the Ceiling Canopy as shown in STEP 8.
Fixture Chain
Ceiling Canopy
STEP 12:
Use Wire Connectors to connect the wires.
WHITE OR RIBBED WHITE OR RIBBED
a. Connect the House Ground Wire to the Fixture Ground
Wire. FROM HOUSE FROM FIXTURE
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture BLACK (OR RED) WIRE BLACK OR SMOOTH
Supply Wire (Black or Smooth Side).
FROM HOUSE FROM FIXTURE
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box. GROUND WIRE GROUND WIRE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5 OF 5