DESCRIPTION/ORDERING INFORMATION
The MC33078 is a bipolar dual operational amplifier with high-performance specifications for use in quality audio
and data-signal applications. This device operates over a wide range of single- and dual-supply voltages and
offers low noise, high-gain bandwidth, and high slew rate. Additional features include low total harmonic
distortion, excellent phase and gain margins, large output voltage swing with no deadband crossover distortion,
and symmetrical sink/source performance.
ORDERING INFORMATION
TA PACKAGE (1) ORDERABLE PART NUMBER TOP-SIDE MARKING (2)
PDIP – P Tube of 50 MC33078P MC33078P
Tube of 75 MC33078D
SOIC – D M33078
–40°C to 85°C Reel of 2500 MC33078DR
Reel of 2500 MC33078DGKR
VSSOP/MSOP – DGK MY_
Reel of 250 MC33078DGKT
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
(2) DGK: The actual top-side marking has one additional character that designates the assembly/test site.
IN+ +
OUT
IN − −
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Copyright © 2004–2006, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
MC33078
DUAL HIGH-SPEED LOW-NOISE OPERATIONAL AMPLIFIER www.ti.com
SLLS633C – OCTOBER 2004 – REVISED NOVEMBER 2006
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC–.
(3) The magnitude of the input voltage must never exceed the magnitude of the supply voltage.
(4) Excessive input current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs, unless
some limiting resistance is used.
(5) The output may be shorted to ground or either power supply. Temperature and/or supply voltages must be limited to ensure the
maximum dissipation rating is not exceeded.
(6) Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
(7) The package thermal impedance is calculated in accordance with JESD 51-7.
Electrical Characteristics
VCC– = –15 V, VCC+ = 15 V, TA = 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
TA = 25°C 0.15 2
VIO Input offset voltage VO = 0, RS = 10 Ω, VCM = 0 mV
TA = –40°C to 85°C 3
Input offset voltage
αVIO VO = 0, RS = 10 Ω, VCM = 0 TA = –40°C to 85°C 2 µV/°C
temperature coefficient
TA = 25°C 300 750
IIB Input bias current VO = 0, VCM = 0 nA
TA = –40°C to 85°C 800
TA = 25°C 25 150
IIO Input offset current VO = 0, VCM = 0 nA
TA = –40°C to 85°C 175
Common-mode input voltage
VICR ∆VIO = 5 mV, VO = 0 ±13 ±14 V
range
Large-signal differential TA = 25°C 90 110
AVD RL ≥ 2 kΩ, VO = ±10 V dB
voltage amplification TA = –40°C to 85°C 85
VOM+ 10.7
RL = 600 Ω
VOM– –11.9
VOM+ 13.2 13.8
VOM Maximum output voltage swing VID = ±1 V RL = 2k Ω V
VOM– –13.2 –13.7
VOM+ 13.5 14.1
RL = 10k Ω
VOM– –14 –14.6
CMMR Common-mode rejection ratio VIN = ±13 V 80 100 dB
kSVR (1) Supply-voltage rejection ratio VCC+ = 5 V to 15 V, VCC– = –5 V to –15 V 80 105 dB
Source current 15 29
IOS Output short-circuit current |VID| = 1 V, Output to GND mA
Sink current –20 –37
TA = 25°C 2.05 2.5
ICC Supply current (per channel) VO = 0 mA
TA = –40°C to 85°C 2.75
Operating Characteristics
VCC– = –15 V, VCC+ = 15 V, TA = 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate at unity gain AVD = 1, VIN = –10 V to 10 V, RL = 2 kΩ, CL = 100 pF 5 7 V/µs
GBW Gain bandwidth product f = 100 kHz 10 16 MHz
B1 Unity gain frequency Open loop 9 MHz
CL = 0 pF –11
Gm Gain margin RL = 2 kΩ dB
CL = 100 pF –6
CL = 0 pF 55
Φm Phase margin RL = 2 kΩ deg
CL = 100 pF 40
Amp-to-amp isolation f = 20 Hz to 20 kHz –120 dB
Power bandwidth VO = 27 V(PP), RL = 2 kΩ, THD ≤ 1% 120 kHz
THD Total harmonic distortion VO = 3 Vrms, AVD = 1, RL = 2 kΩ, f = 20 Hz to 20 kHz 0.002 %
zo Open-loop output impedance VO = 0, f = 9 MHz 37 Ω
rid Differential input resistance VCM = 0 175 kΩ
Cid Differential input capacitance VCM = 0 12 pF
Vn Equivalent input noise voltage f = 1 kHz, RS = 100 Ω 4.5 nV/√Hz
In Equivalent input noise current f = 1 kHz 0.5 pA/√Hz
0.1 µF
10 Ω 100 kΩ
2.0 kΩ
4.3 kΩ 22 µF
D.U.T. +
1/2 Scope
MC33078
− x1
4.7 µF RIN = 1.0 MΩ
100 kΩ
Voltage Gain = 50,000 2.2 µF
24.3 kΩ 110 kΩ
0.1 µF
TYPICAL CHARACTERISTICS
600 600
VCC+ = 15 V VCM = 0 V
VCC– = –15 V TA = 25°C
500 500
TA = 25°C
400 400
300
300
200
200
100
100
0
0
5 6 7 8 9 10 11 12 13 14 15 16 17 18
-15 -10 -5 0 5 10 15
VCC+/–VCC– – Supply Voltage – V
VCM – Common Mode Voltage – V
1000 2
VCC+ = 15 V VCC+ = 15 V
900 VCC– = –15 V 1.5 VCC– = –15 V
800 VCM = 0 V VCM = 0 V
VIO – Input Offset Voltage – mV
IIB – Input Bias Current – nA
1
700
600 0.5
500 0
400
-0.5
300
-1
200
100 -1.5
0 -2
-55 -35 -15 5 25 45 65 85 105 125 -55 -35 -15 5 25 45 65 85 105 125
TA – Temperature – °C TA – Temperature – °C
1.4 0
VCC+ = 3 V to 15 V
1.2 -0.2 VCC– = -3 V to -15 V
Input Common-Mode Voltage Low
-0.4
Proximity to V CC+ – V
0.8 -0.6
0.6
-0.8
VCC+ = 3 V to 15 V
0.4
VCC– = -3 V to -15 V -1
D
è VIO = 5 mV
0.2
VO = 0 V -1.2
0
-1.4
-55 -25 5 35 65 95 125
-55 -25 5 35 65 95 125
TA – Temperature – °C
TA – Temperature – °C
OUTPUT SATURATION VOLTAGE PROXIMITY TO VCC+ OUTPUT SATURATION VOLTAGE PROXIMITY TO VCC–
vs vs
LOAD RESISTANCE LOAD RESISTANCE
0 10
-1 9
TA = 125°C
-2 8
Output Saturation Voltage
TA = 25°C
Output Saturation Voltage
Proximity to V CC+ – V
Proximity to V CC– – V
-3 7
TA = –55°C
-4 6
-5 5
TA = 125°C
-6 4
TA = 25°C
-7 3
TA = –55°C
-8 2
-9 1
-10 0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
kW
RL – Load Resistance – kh kW
RL – Load Resistance – k@
70 10
VCC+ = 15 V
9 VCM = 0 V
IOS – Output Short-Circuit Current – mA
VCC– = –15 V
60 RL = High Impedance
VID = 1 V 8
VO = 0 V
6
VCC± = ±15 V
40 5
Source
Sink 4
30
3 VCC± = ±10 V
VCC± = ±5 V
20 2
1
10
0
-55 -35 -15 5 25 45 65 85 105 125
-55 -35 -15 5 25 45 65 85 105 125
TA – Temperature – °C
TA – Temperature – °C
CMRR PSSR
vs vs
FREQUENCY FREQUENCY
100 120
VCC+ = 15 V VCC+ = 15 V
90 VCC– = –15 V 110
VCC– = –15 V
VCM = 0 V 100 TA = 25°C
80 DVCM = ±1.5 V
TA = 25°C 90
70
80
60
CMMR – dB
PSRR – dB
70
T3P
50 60
40 50
T3N
40
30
30
20
20
10 10
0 0
100
1.0E+02 1k
1.0E+03 10k
1.0E+04 100k 1.0E+06
1.0E+05 1M 10M
1.0E+07 1.0E+02 1.0E+03 1.0E+04 1.0E+05
100 1k 10k 100k 1.0E+06
1M 1.0E+07
10M
f – Frequency – Hz f – Frequency – Hz
30 30
GBW – Gaind Bandwidth Product – MHz
20 20
15 15
10
10
5
5
0
0
-55 -35 -15 5 25 45 65 85 105 125
5 6 7 8 9 10 11 12 13 14 15 16 17 18
TA – Temperature – °C
VCC+/–VCC– – Supply Voltage – V
20 30
VCC+ = 15 V
VCC– = –15 V
15 RL = 2 k W
RL = 10 kW 25 AV = 1
10 THD < 1%
VO – Output Voltage – V
VO – Output Voltage – V
TA = 25°C
RL = 2 k W
20
5
0 15
-5
RL = 10 kW 10
-10
RL = 2 kW 5
-15
-20 0
5 6 7 8 9 10 11 12 13 14 15 16 17 18 10
1.E+01 100
1.E+02 1k
1.E+03 10k
1.E+04 100k 1.E+06
1.E+05 1M 10M
1.E+07
VCC+/–VCC– – Supply Voltage – V f – Frequency – Hz
110 120
RL = 2 k W
f < 10 Hz
115
105 DVO = 2/3(VCC+ – VCC–)
TA = 25°C
AV – Open-Loop Gain – dB
AV – Open-Loop Gain – dB
110
100
105
95 100
95
90
RL = 2 kW 90
85 f < 10 Hz
DVO = 2/3(VCC+ – VCC–) 85
TA = 25°C
80 80
5 6 7 8 9 10 11 12 13 14 15 16 17 18 -55 -35 -15 5 25 45 65 85 105 125
VCC+/–VCC– – Supply Voltage – V TA – Temperature – °C
50 200
Drive Channel
VCC+ = 15 V
190 VCC+ = 15 V
45 VCC– = –15 V VCC– = –15 V
40 VO = 1 Vrms 180 RL = 2 kW
VO = 20 VPP
ZO – Output Impedance – W
Crosstalk Rejection – dB
TA = 25°C
35 170 TA = 25°C
30 160
150
25
140
20
130
15
AV = 1000 120
10
AV = 100 AV = 10 AV = 1
110
5
100
0 1.E+01
10 1.E+02
100 1.E+03
1k 1.E+04
10k 1.E+05
100k
1.0E+03
1k 1.0E+04
10k 1.0E+05
100k 1.0E+06
1M 1.0E+07
10M
f – Frequency – Hz
f – Frequency – Hz
1 1
VCC+ = 15 V
VCC– = –15 V
VO = 1 Vrms AV = 1000
THD – Total Harmonic Distortion – %
0.01 0.01
AV = 10
0.001 0.001
VCC+ = 15 V
AV = 1
VCC– = –15 V
f = 2 kHz
RL = 2 kW
TA = 25°C
0.0001 0.0001
10
1.E+01 100
1.E+02 1k
1.E+03 10k
1.E+04 100k
1.E+05 0 1 2 3 4 5 6 7 8 9
f – Frequency – Hz VO – Output Voltage – Vrms
10 10
9 9
8 Falling Edge 8
Falling Edge
SR – Slew Rate – V/µs
7 7
Rising Edge Rising Edge
6 6
5
5
VCC+ = 15 V
4 DV = 2/3(V – V ) VCC– = –15 V
IN CC+ CC– 4
AV = 1 DVIN = 20 V
3 RL = 2 kW AV = 1
TA = 25°C 3 RL = 2 kW
2
5 6 7 8 9 10 11 12 13 14 15 16 17 18 2
-55 -35 -15 5 25 45 65 85 105 125
VCC+/–VCC– – Supply Voltage – V
TA – Temperature – °C
80 0 12 0
Phase Gain, TA = 125°C VCC+ = 15 V
VCC– = –15 V
70 VO = 0 V 10
Gain, TA = 25°C
60 -45 9 20
Gain Margin – dB
Phase Shift – deg
50 30
Gain – dB
40 -90 6 40
Phase, TA = 125°C
30 50
20 -135 3 60
VCC+ = 15 V Phase, TA = 25°C
VCC– = –15 V
10 RL = 2 k W 70
Phase, TA = –55°C
TA = 25°C
0 -180 0 80
1.E+03
1k 1.E+04
10k 1.E+05
100k 1.E+06
1M 1.E+07
10M 1 10 100 1000
100 100 10
VCC+ = 15 V VCC+ = 15 V
90
VCC– = –15 V VCC– = –15 V
80 VIN = 100 mVPP TA = 25°C
Input Voltage Noise – nV/rtHz
pA/ÖHz
70
Overshoot – %
60
50 10 1
1000 16 64
VCC+ = 15 V 60
VCC– = –15 V 14 56
Input Referred Noise Voltage – nV/rtHz
nV/ÖHz
f = 1 Hz 52
TA = 25°C 12 48
Phase Margin
100 44
VO = 0 V 12
2 TA = 25°C 8
4
1
0 0
1.E+01
10 1.E+02
100 1.E+03
1k 1.E+04
10k 1.E+05
100k 1.E+06
1M 00 1 10
10 100
10 0 101k
00 1010k
0 0 0 10100k
0000
RS – Source Resistance – W
è RSD – Differential Source Resistance – W
è
Input Input
55 10 55 10
45 0 45 0
VO – Output Voltage – V
VO – Output Voltage – V
VI – Input Voltage – V
VI – Input Voltage – V
35 -10 35 -10
VCC+ = 15 V
VCC+ = 15 V VCC– = –15 V
25 VCC– = –15 V -20 25 AV = –1 -20
AV = 1 RL = 2 k W
RL = 2 k W CL = 100 pF
15 CL = 100 pF -30 15 TA = 25°C -30
Output Output
TA = 25°C
5 -40 5 -40
-5 -50 -5 -50
200
0.4 0.0
VI – Input Voltage – V
Input 100
0.3 -0.1
VCC+ = 15 V
VCC– = –15 V
0
0.2 AV = 1 -0.2
RL = 2 k W -100
0.1 CL = 100 pF -0.3
TA = 25°C -200 T3
0 -0.4 VCC+ = 15 V
-300
Output VCC– = –15 V
-0.1 -0.5 -400 BW = 0.1 Hz to 10 Hz
TA = 25°C
-0.2 -0.6 -500
-0.5 0.0 0.5 1.0 1.5 -5 -4 -3 -2 -1 0 1 2 3 4 5
Time – µs Time – s
APPLICATION INFORMATION
Output Characteristics
All operating characteristics are specified with 100-pF load capacitance. The MC33078 can drive higher
capacitance loads. However, as the load capacitance increases, the resulting response pole occurs at lower
frequencies, causing ringing, peaking, or oscillation. The value of the load capacitance at which oscillation
occurs varies from lot to lot. If an application appears to be sensitive to oscillation due to load capacitance,
adding a small resistance in series with the load should alleviate the problem (see Figure 2).
15 V
RO
5V VO
–5 V
–15 V
CL RL = 2 k Ω
PACKAGING INFORMATION
Orderable Device Status (1) Package Package Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Type Drawing Qty
MC33078D ACTIVE SOIC D 8 75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DE4 ACTIVE SOIC D 8 75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DG4 ACTIVE SOIC D 8 75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DGKR ACTIVE MSOP DGK 8 2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DGKRG4 ACTIVE MSOP DGK 8 2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DGKT ACTIVE MSOP DGK 8 250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DGKTG4 ACTIVE MSOP DGK 8 250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DR ACTIVE SOIC D 8 2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DRE4 ACTIVE SOIC D 8 2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MC33078P ACTIVE PDIP P 8 50 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
MC33078PE4 ACTIVE PDIP P 8 50 Pb-Free CU NIPDAU N / A for Pkg Type
(RoHS)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com 18-Sep-2008
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 2
MECHANICAL DATA
0.400 (10,60)
0.355 (9,02)
8 5
0.260 (6,60)
0.240 (6,10)
1 4
0.070 (1,78) MAX
0.325 (8,26)
0.020 (0,51) MIN
0.300 (7,62)
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
4040082/D 05/98