ACCESS POINT
USER
MANUAL
MODELS:
524704
524728
524735
INT-524704/524728/524735-UM-0809-03
Federal Communications Commission
Interference Statement
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference;
and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate the equipment.
This equipment complies with FCC radiation exposure set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20 cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacturer must therefore be allowed
at all times to ensure the safe use of the equipment.
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden and the United
Kingdom.
The ETSI version of this device is also authorized for use in EFTA member
states Iceland, Liechtenstein, Norway and Switzerland.
None.
Table of Contents
1
1-2 Safety Information
6. The access point will become hot when in use for long time.
This is normal and is not a malfunction. DO NOT put this
access point on paper, cloth or other flammable materials.
8. If the access point falls into water when it’s powered, DO NOT
use your hands to pick it up. Switch the electrical power off
before you do anything, or contact an experienced electrical
technician for help.
2
1-3 System Requirements
3
1-4 Package Contents
Before you start to use this access point, check to see if there’s
anything missing in the package. If so, contact your dealer of
purchase.
4
1-5 Connections and Indicators
Front Panel
5
Back Panel
6
Chapter II: System and Network Setup
2. Connect the A/C power adapter to the wall socket, then connect
it to the Power jack of the access point.
3. Check all LEDs on the front panel. The PWR LED should be
steadily on; the LAN LED should be on if the access point is
correctly connected to the ADSL modem, router or switch/hub. If
the PWR LED is not on, or if any LED you expect to be on isn’t,
recheck the cabling or refer to 4-2 Troubleshooting for possible
causes and solutions.
7
2-2 Connecting to wireless access point by Web browser
After the network connection is made, the next step is to set up the
access point with proper network parameters so it can work
properly in your network environment.
Before you can connect to the access point and start configuration
procedures, your computer must be able to get an IP address
automatically (use a dynamic IP address). If it’s set to use a static
IP address, or if you’re unsure, follow the instructions below to
configure your computer to use a dynamic IP address:
8
2. Select “Specify an IP address,” then enter the following settings
in their respective fields:
IP address: 192.168.2.2
Subnet Mask: 255.255.255.0
9
2-2-2 Windows 2000 IP address setup
10
2. Select “Use the following IP address,” then enter the following
settings in their respective fields:
IP address: 192.168.2.2
Subnet Mask: 255.255.255.0
11
2-2-3 Windows XP IP address setup
12
2. Select “Use the following IP address,” then enter the following
settings in their respective fields:
IP address: 192.168.2.2
Subnet Mask: 255.255.255.0
13
2-2-4 Windows Vista IP address setup
14
2. Select “Use the following IP address,” then enter the following
settings in their respective fields:
IP address: 192.168.2.2
Subnet Mask: 255.255.255.0
15
16
2-2-5 Connecting to the Web Management Interface
17
NOTE: If you can’t see the Web management interface and you’re being
prompted to input a username and password again, it means you didn’t
input the username and password correctly. Re-enter the username
and password. If you’re certain the username and password you
entered are correct, go to 4-2 Troubleshooting to perform a factory
reset and set the password back to its default value.
18
2-3 View System Status and Information
You can click Home on the left while viewing other screens, as well,
and the system status and information will be displayed, as shown:
19
Hardware Displays hardware version. This information is
Version helpful when you need online help from the
dealer.
Runtime Code Displays current firmware version. If you want
Version to perform a firmware upgrade, this number
will help you to determine if you need such an
upgrade.
Mode Displays current wireless operating mode (see
next section).
ESSID Displays current ESSID (the name used to
identify this wireless access point.
Channel Displays current wireless channel number.
Number
Security Displays current wireless security setting.
BSSID Displays current BSSID (a unique
identification of this access point that can not
be modified by the user).
Associated Displays the number of connected wireless
Clients clients.
IP Address Displays the IP address of this wireless access
point.
Subnet Mask Displays the net mask of IP address.
Default Gateway Displays the IP address of default gateway.
MAC address Displays the MAC address of LAN interface.
20
2-4 Select an Operating Mode for the Wireless Access Point
This access point can be operated in different modes: You can click
Basic Settings on the left of the Web management interface to
select an operating mode you want to meet for different needs.
21
same mode, and links the wired network
that connects these two wireless access
points. Only one access point can be
connected in this mode.
AP Bridge-Point to Establishes a wireless connection with other
Multi-Point wireless access points using the same
mode, and links the wired network that
connects these two wireless access points.
Up to four access points can be connected
in this mode.
AP Bridge-WDS This mode is similar to AP Bridge to Multi-
Point. While the access point doesn’t work
in bridge-dedicated mode, it will be able to
accept wireless clients while the access
point is working as a wireless bridge.
Universal Repeater This product can act as a wireless range
extender that will help you extend the
network wirelessly. The access point can act
as Station and AP at the same time. It can
use the Station function to connect to a root
AP and use the AP function to service all
wireless clients within its coverage.
22
2-4-1 AP Mode
23
wireless access point) here. You can input up
to 32 alphanumerical characters. NOTE:
THE ESSID IS CASE SENSITIVE.
Multiple ESSID The access point supports multiple SSID
functions; up to four SSIDs can be set. If you
want to configure additional SSIDs, click this
button. For detailed descriptions of the
function, refer to Section 2-4-1-1.
Channel Select a channel number you wish to use. If
Number you know a certain channel number is being
used by other wireless access points nearby,
refrain from using the same channel number.
Associated Click the Show Active Clients button and a
Clients new popup window will appear which contains
the information about all wireless clients
connected to this access point. You can click
the Refresh button in the popup window to
keep information up to date.
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. You can click “Continue” to go back to the
previous page and continue with other settings, or click “Apply” to
restart the wireless access point. Changes will take effect after
about 30 seconds.
24
2-4-1-1 Multiple ESSIDs
This access point supports four SSIDs. Except for the main SSID
(configured on the Basic Settings page), you can configure another
three SSIDs here. With different SSIDs, you can separate the
wireless networks with different SSID names, wireless security,
WMM and VLAN settings.
25
Broadcast SSID Decide if the wireless access point will
broadcast its own ESSID or not. You can hide
the ESSID of your wireless access point (set
the option to “Disable”) so only those who
know the ESSID of your wireless access point
can get connected.
WMM WMM (Wi-Fi Multimedia) technology can
improve the performance of certain network
applications, like audio/video streaming,
network telephony (VoIP) and others. When
you enable the WMM function, the access
point will define the priority of different kinds of
data to give higher priority to applications that
require instant response. Therefore, you can
improve the performance of such network
applications.
VLAN ID If your network uses VLANs, you can assign
(0:Untagged) the SSID to a VLAN on your network. Client
devices that associate using the SSID are
grouped into this VLAN. The VLAN ID range is
from 1 to 4094. The VLAN ID is 0 by default,
meaning that it disables the VLAN function for
the ESSID.
2-4-2 Station-Infrastructure
26
Here are descriptions of every setup item:
After you finish with the settings, click “Apply” and the following
message will be displayed:
27
When you see this message, the settings you made are
successfully saved. You can click “Continue” to go back to the
previous page and continue with other settings or click “Apply” to
restart the wireless access point. Changes will take effect after
about 30 seconds.
The table will list the access points nearby as the access point is
set to Station mode. You can select one of the access points to
associate with.
28
Here are descriptions of every setup item:
NOTE: When you set your access point to this mode, it will not
accept regular wireless clients anymore.
29
Here are descriptions of every setup item:
30
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
31
2-4-4 AP Bridge-Point to Multi-Point Mode
NOTE: When you set your access point to this mode, it will not
accept regular wireless clients anymore.
32
If you select 2.4 GHz (B+G), then only wireless
clients using 802.11b and 802.11g bands will
be able to connect to this access point.
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other setting, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
33
2-4-5 AP Bridge-WDS Mode
When you use this mode, this access point is still able to accept
wireless clients.
34
Draft-N or 802.11g) will be able to connect to
this access point.
After you finish with setting, click “Apply” and the following
message will be displayed:
35
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
In this mode, the access point can act as a wireless repeater: It can
be Station and AP at the same time. It can use the Station function
to connect to a root AP and use the AP function to service all
wireless stations within its coverage.
36
Here are descriptions of every setup item:
37
act as a station to connect to a root AP. You
should assign the SSID of the root AP here or
click “Select Site Survey” to choose a root AP.
Select Site Click “Select Site Survey” and a “Wireless Site
Survey Survey Table” will pop up. It will list all
available access points nearby. You can select
one access point in the table and the access
point will join the wireless LAN through this
access point. Go to Section 2-4-2-1 for more
information about the Wireless Site Survey
Table.
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
38
2-5 WPS Setting
NOTE: The WPS function of this access point will not work
for wireless clients that do not support WPS.
39
Here are descriptions of every setup item:
40
Authentication Mode: The wireless security
authentication mode of this access point will
be displayed here. If you don’t enable a
security function of the access point before
WPS is activated, the access point will auto-
set the security to WPA (AES) and generate a
set of passphrase keys for WPS connection.
41
2-6 Advanced Wireless Settings
42
unless you know what it does.
DTIM Period Set the DTIM period of the wireless radio. Do
not modify the default value (3) unless you
know what it does.
Data Rate Set the wireless data transfer rate to a certain
value. Since most of wireless devices will
negotiate with each other and pick a proper
data transfer rate automatically, it’s not
necessary to change this value unless you
know what will happen after modification.
N Data Rate Set the data rate of 802.11 Draft-N clients:
MCS 0 to MCS 15: It’s safe to set this option to
“Auto” and it’s not necessary to change this
value unless you know what will happen
after modification.
Channel Width Select the wireless channel width (bandwidth
taken by wireless signals of this access point).
It’s suggested to select “Auto 20/40 MHz.” Do
not change to “20 MHz” unless you know what
it is.
Preamble Type Set the type of preamble of the wireless radio,
Do not modify the default (Short Preamble)
unless you know what will happen after
modification.
Broadcast Decide if the wireless access point will
ESSID broadcast its own ESSID or not. You can hide
the ESSID of your wireless access point (set
the option to ‘Disable’) so only those who know
the ESSID of your wireless access point can
get connected.
WMM WMM (Wi-Fi Multimedia) technology can
improve the performance of certain network
applications, like audio/video streaming,
network telephony (VoIP) and others. When
you enable the WMM function, the access
point will define the priority of different kinds of
data to give higher priority to applications that
require instant response. Therefore, you can
43
improve the performance of such network
applications.
CTS Protect Enabling this setting will reduce the chance of
radio signal collisions between 802.11b and
802.11g wireless access points. It’s
recommended to set this option to “Auto.”
TX Power You can set the output power of the wireless
radio. Unless you’re using this wireless access
point in a really big space, you may not have to
set output power to 100%. This will enhance
security (malicious/unknown users outside
the range will not be able to reach your
wireless access point).
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
44
2-7 Wireless Security
45
There are four types of security level you can select: Disable (no
security - data encryption disabled), WEP, WPA Pre-shared Key
and WPA RADIUS. Refer to the following sections for detailed
instructions.
46
2-7-1 Disable Security
Select the SSID you want to configure. When you select “Disable,”
wireless encryption for the network is disabled.
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
47
2-7-2 WEP
Key Length There are two types of WEP key length: 64-bit
and 128-bit. Using “128-bit” is safer than
“64-bit,” but will reduce some data transfer
performance.
Key Format There are two types of key format: ASCII and
Hex. When you select a key format, the
number of key characters will be displayed.
For example, if you select “64-bit” as the key
48
length and “Hex” as key format, you’ll see the
message at the right of “Key Format” is “Hex
(10 characters,” which means the length of the
WEP key is 10 characters.
Default Tx Key You can set up to four sets of WEP keys, and
you can decide which key is being used by
default here. If you don’t know which one
you should use, select “Key 1.”
Encryption Key 1 Input WEP key characters here. The number
to 4 of characters must be the same as the number
displayed in the “Key Format” field. You can
use any alphanumerical characters (0-9, a-z
and A-Z) if you select “ASCII” key format; if
you select “Hex” as the key format, you can
use characters 0-9, a-f and A-F. You must
enter at least one encryption key here; if you
enter multiple WEP keys, they should all be
different.
Enable 802.1x Check to enable 802.1x user authentication.
Authentication Refer to Section 2-7-5 for detailed instructions.
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
49
2-7-3 WPA Pre-shared Key
After you finish with the settings, click “Apply” and the following
message will be displayed:
50
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
51
2-7-4 WPA RADIUS
WPA Unicast You can select the WPA encryption type here.
Cipher Suite AES is safer than TKIP, but not every wireless
client supports it. Refer to the specifications of
your wireless client to decide which encryption
type you should use.
Use internal Uses the built-in RADIUS Server (refer to
MD5/PEAP Section 2-8) instead of an external RADIUS
RADIUS Server server. If you check this box, the values in the
following three fields will be ignored.
RADIUS Server Input the IP address of the RADIUS
IP address authentication server here.
RADIUS Server Input the port number of the RADIUS
Port authentication server here. Default value is
1812.
RADIUS Server Input the password of the RADIUS
Password authentication server here.
52
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
53
2-7-5 802.1x Authentication
After you finish with the settings, click “Apply” and the following
message will be displayed:
54
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
55
2-8 RADIUS Server
56
Here are descriptions of every setup item:
After you finish with the settings, click “Apply” and the following
message will be displayed:
57
When you see this message, the settings you made are
successfully save. Click “Continue” to go back to the previous page
and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
58
2-9 MAC Filtering
To set up MAC filtering, click MAC Filtering on the left side of the
Web management interface and the following messages will be
displayed:
Address
filtering
table (1)
Add
new entry
here (2)
This page contains two parts of MAC filtering information. All
allowed MAC addresses will be listed in the upper part (1), and you
can add new MAC addresses by components in the lower part (2).
59
Enable Wireless Check this box to enable MAC address
Access Control restriction. If unchecked, no restriction will be
enforced (any wireless client with the proper
encryption setting will be able to connect to
this wireless access point).
MAC address Input a MAC address allowed using this
wireless access point here. You don’t have to
add a colon (:) or hyphen (-) yourself: Just
input 0 to 9 and a to f here; e.g.,
112233445566 or aabbccddeeff.
Comment You can input any text here as a comment for
this MAC address; e.g., “Room 2 Computer.”
Input up to 16 alphanumerical characters. This
is optional and you can leave it blank; but it’s
recommended that you write a comment for
every MAC address as a memory aid.
Add When you finish inputting a MAC address and
(optional) comment, click to add the MAC
address to the list.
Clear Remove all characters in the “MAC address”
and “Comments” fields.
After you finish with the settings, click “Apply” and the following
message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other setting, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
60
2-10 System Utilities
You can change the password used to enter the Web configuration
menu of this wireless access point.
Click System Utility on the left, and the following will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
61
2-10-2 IP Address of the Wireless Access Point
To change the IP address, click System Utility on the left, and the
following message will be displayed:
62
Click “Apply” and the following message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
63
2-10-3 DHCP Server
This wireless access point is able to act as a DHCP server for your
network, and it’s disabled by default. If you want to activate this
function, click System Utility on the left side, and the following
message will be displayed:
64
Click “Apply” and the following message will be displayed:
When you see this message, the settings you made are
successfully saved. Click “Continue” to go back to the previous
page and continue with other settings, or click “Apply” to restart the
wireless access point. Changes will take effect after about 30
seconds.
65
Chapter III: Advanced Configuration
66
3-2 Firmware Upgrade
If there is new firmware available for this wireless access point, you
can upload it to the access point to incorporate added functions or
to effect solutions to problems.
67
3-3 System Reset
This function is useful when the access point isn’t within easy reach
physically. However, if the access point is not responding, you may
have to switch it off by unplugging the power cord and plugging it
back in after 10 seconds.
To reset your access point, click Reset on the left. The following
message will be displayed:
Click “Apply” and a pop-up message will ask you again to make
sure you really want to reset the access point:
68
Chapter IV: Troubleshooting
Scenario Solution
Access point is not a. Check the connection of the power cord
responding when I and network cable of this access point.
want to access it by All cords and cables should be correctly
Web browser and firmly inserted.
b. If all LEDs on this access point are out,
check the status of the A/C power
adapter and make sure it’s correctly
powered.
c. You must use the same IP address
section the access point uses.
d. Are you using a MAC or IP address
filter? Try to connect the access point by
another computer and see if it works; if
not, perform a hard reset (press the
Reset button).
e. Set your computer to obtain an IP
address automatically (DHCP) and see
if your computer can get an IP address.
f. If you did a firmware upgrade and this
happens, contact your dealer for help.
g. If all above solutions don’t work, contact
the dealer for help.
Can’t get connected a. If encryption is enabled, re-check the
to the wireless WEP or WPA passphrase settings on
access point your wireless client.
b. Try to move closer to the wireless
access point.
c. Unplug the power plug of the access
point and plug it back in after 10
seconds.
69
d. If all LEDs on this access point are out,
check the A/C power adapter and make
sure it’s correctly powered.
I can’t locate my a. Is “Broadcast ESSID” set to “Off”?
access point by my b. Is the antenna properly installed and
wireless client secured?
c. Are you too far from your access point?
Try to get closer.
d. Remember that you have to input the
ESSID on your wireless client manually if
ESSID broadcast is disabled.
File download is a. Try to reset the access point and see if
very slow or breaks it’s better after that.
frequently b. See what computers do on your local
network. If someone’s transferring large
files, others will think the Internet is
really slow.
c. Change the channel number and see if
this works.
I can’t log on to the a. Make sure you’re connecting to the
Web management correct IP address of the access point.
interface: password b. Password is case-sensitive. Make sure
is wrong the Caps Lock light is not illuminated.
c. If you forget the password, do a hard
reset.
Access point a. This is not a malfunction. If you can
becomes hot keep your hand on the access point’s
chassis, it’s okay.
b. If you smell something wrong or see
smoke coming from the access point or
A/C power adapter, disconnect from
utility power (make sure it’s safe before
you’re doing this!) and call your dealer
for help.
70
Chapter V: Glossary
DNS Server IP Address: DNS stands for Domain Name System, which
allows Internet servers to have a domain name (such as
www.Broadbandaccesspoint.com) and one or more IP addresses (such as
192.34.45.8). A DNS server keeps a database of Internet servers and their
respective domain names and IP addresses, so that when a domain name is
requested (as in typing "Broadbandaccesspoint.com" into your Internet
browser) the user is sent to the proper IP address. The DNS server IP address
used by the computers on your home network is the location of the DNS server
your ISP has assigned to you.
DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses
your existing phone lines to transmit data at high speeds.
Idle Timeout: Idle Timeout is designed so that after there is no traffic to the
Internet for a pre-configured amount of time the connection will automatically
be disconnected.
For example, if the IP address for a device is, in its binary form,
11011001.10110000.10010000.00000111, and if its network mask is,
11111111.11111111.11110000.00000000
It means the device’s network address is
11011001.10110000.10010000.00000000, and its host ID is,
00000000.00000000.00000000.00000111. This is a convenient and efficient
method for access points to route IP packets to their destination.
ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is
an IP address for the Internet access point located at the ISP's office.
MAC Address: MAC stands for Media Access Control. A MAC address is the
hardware address of a device connected to a network. The MAC address is a
unique identifier for a device with an Ethernet interface. It is composed of two
parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each
manufacturer), plus 3 bytes that are often used as the product’s serial number.
NAT: Network Address Translation. This process allows all of the computers
on your home network to use one IP address. Using the broadband access
point’s NAT capability, you can access the Internet from any computer on your
home network without having to purchase more IP addresses from your ISP.
72
Port: Network Clients (LAN PC) uses port numbers to distinguish one network
application/protocol over another. Below is a list of common applications and
protocol/port numbers:
Subnet Mask: A subnet mask, which may be a part of the TCP/IP information
provided by your ISP, is a set of four numbers (e.g., 255.255.255.0) configured
73
like an IP address. It is used to create IP address numbers used only within a
particular network (as opposed to valid IP address numbers recognized by the
Internet, which must be assigned by InterNIC).
74
Chapter VI: Specifications
Standards
• IEEE 802.1d (Spanning Tree Protocol)
• IEEE 802.11b (11 Mbps Wireless LAN)
• IEEE 802.11g (54 Mbps Wireless LAN)
• IEEE 802.11n Draft 2.0 (300 Mbps Wireless LAN)
• IEEE 802.1x (Network Access Control)
• IEEE 802.3 (10Base-T Ethernet)
• IEEE 802.3u (100Base-TX Fast Ethernet)
• IEEE 802.3af (Power over Ethernet) — Model 524735 only
General
• LAN port: RJ45 10/100 Mbps data port
• LAN port with Auto MDI/MDI-X
• Flash: 4 MB
• Memory: 16 MB SDRAM
• Certifications: FCC Class B, CE, RoHS
Wireless
• Chipset: Ralink
- Model 524704: RT3050
- Models 524728 and 524735: RT3052
• Wireless frequency range: 2.400 – 2.4835 GHz
• Modulation technologies:
- 802.11b: Direct Sequence Spread Spectrum (DSSS): DBPSK,
DQPSK, CCK
- 802.11g: Orthogonal Frequency Division Multiplexing (OFDM):
BPSK, QPSK, 16QAM, 64QAM
- 802.11n: Orthogonal Frequency Division Multiplexing (OFDM):
BPSK, QPSK, 16QAM, 64QAM
• Data rates:
- IEEE 802.11b (11 Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps)
- IEEE 802.11g (54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps,
12 Mbps, 9 Mbps, 6 Mbps)
- IEEE 802.11n (MCS0-15: up to 300 Mbps for Models 524728
and 524735); (MCS0-7: up to 150 Mbps for Model 524704)
75
• Output power:
- OFDM: 14 dBm +/- 1.5 dBm (300 Mbps, 40 mW max. for
Models 524728 and 524735; 150 Mbps, 40 mW max. for
Model 524704)
- OFDM: 15 dBm +/- 1.5 dBm (54 Mbps, 40 mW max.)
- CCK: 17 dBm +/- 1 dBm (11 Mbps, 63 mW max.)
• Receiver sensitivity:
- 11n (300 Mbps) MCS0-15 for Models 524728 and 524735:
20 MHz: -73 dBm; 40 MHz: -68 dBm
- 11n (150 Mbps) MCS0-7 for Model 524704:
20 MHz: -73 dBm; 40 MHz: -68 dBm
- 11g (54 Mbps) OFDM: -78 dBm
- 11b (11 Mbps) CCK: -91 dBm
• Wireless operation modes:
- Access Point
- Station Infrastructure (AP Client)
- Point-to-Point Bridge
- Point-to-Multi-Point Bridge
- WDS Bridge
- Universal Repeater
• Wireless security:
- WEP encryption (64/128 bit)
- WPA TKIP
- WPA2 AES
- WPA2 mixed
- WPA RADIUS
- 802.1x Authentication
- Internal MD5/PEAP RADIUS server
- Client access control through media access control (MAC) filter
• Antennas:
- Models 524728 and 524735: 2 detachable dipole antennas with
3 dBi gain each
- Model 524704: 1 detachable dipole antenna with 3 dBi gain
- 2T2R MIMO mode (2 transmitters, 2 receivers) – Models
524728 and 524735 only
LEDs
• Power
• WLAN Link/Act
76
• LAN Link/Act
Environmental
• Dimensions: 160 (W) x 127 (L) x 35 (H) mm (6.3 x 5.0 x 1.4 in.)
• Weight: 0.8 kg (1.7 lbs.)
• Operating temperature: 0 – 40°C (32 – 104°F)
• Operating humidity: 10 – 90% RH, non-condensing
• Storage temperature: -20 – 60°C (4 – 149°F)
Power
• External power adapter: 5 V DC, 1.0 A
• Power consumption: 4 Watts max.
• Via PoE PD port: 48 V, 0.2 A — Model 524735 only
77
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
Disposal of Electric and Electronic Equipment
(applicable in the European Union and other European countries with separate collection systems)
ENGLISH
This symbol on the product or its packaging indicates that this product shall not
be treated as household waste. Instead, it should be taken to an
applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences to
the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. If your equipment contains easily
removable batteries or accumulators, dispose of these separately according to
your local requirements. The recycling of materials will help to conserve
natural resources. For more detailed information about recycling of this
product, contact your local city office, your household waste disposal service
or the shop where you purchased this product. In countries outside of the EU:
If you wish to discard this product, contact your local authorities and ask for the
correct manner of disposal.
DEUTSCH
Dieses auf dem Produkt oder der Verpackung angebrachte Symbol zeigt an,
dass dieses Produkt nicht mit dem Hausmüll entsorgt werden darf. In
Übereinstimmung mit der Richtlinie 2002/96/EG des Europäischen Parlaments
und des Rates über Elektro- und Elektronik-Altgeräte (WEEE) darf dieses
Elektrogerät nicht im normalen Hausmüll oder dem Gelben Sack entsorgt
werden. Wenn Sie dieses Produkt entsorgen möchten, bringen Sie es bitte zur
Verkaufsstelle zurück oder zum Recycling-Sammelpunkt Ihrer Gemeinde.
ESPAÑOL
Este símbolo en el producto o su embalaje indica que el producto no debe
78
tratarse como residuo doméstico. De conformidad con la Directiva 2002/96/CE
de la UE sobre residuos de aparatos eléctricos y electrónicos (RAEEI), este
producto eléctrico no puede desecha se con el resto de residuos no
clasificados. Deshágase de este producto devolviéndolo al punta de venta o a
un punta de recogida municipal para su reciclaje.
FRANÇAIS
Ce symbole sur Ie produit ou son emballage signifie que ce produit ne doitpas
être traité comme un déchet ménager. Conformément à la Directive
2002/96/EC sur les déchets d’équipements électriques et électroniques
(DEEE), ce produit électrique ne doit en aucun cas être mis au rebut sous
forme de déchet municipal non trié. Veuillez vous débarrasser de ce produit en
Ie renvoyant à son point de vente ou au point de ramassage local dans votre
municipalité, à des fins de recyclage.
ITALIANO
Questo simbolo sui prodotto o sulla relativa confezione indica che il prodotto
non va trattato come un rifiuto domestico. In ottemperanza alla Direttiva UE
2002/96/EC sui rifiuti di apparecchiature elettriche ed elettroniche (RAEEI),
questa prodotto elettrico non deve essere smaltito come rifiuto municipale misto.
Si prega di smaltire il prodotto riportandolo al punto vendita o al punto di
raccolta municipale locale per un opportuno riciclaggio.
POLSKI
Jeśli na produkcie lub jego opakowaniu umieszczono ten symbol, wówczas w
czasie utylizacji nie wolno wyrzucać tego produktu wraz z odpadami komunalnymi.
Zgodnie z Dyrektywą Nr 2002/96/WE w sprawie użytego
z sprzętu elektrycznego i
elektronicznego (WEEE), niniejszego produktu elektrycznego nie wolno usuwać
jako nie posortowanego odpadu komunalnego. Prosimy o usuniecie niniejszego
produktu poprzez jego zwrot do punktu zakupu lub oddanie do miejscowego
komunalnego punktu zbiórki odpadów przeznaczonych do recyklingu.
79
WARRANTY INFORMATION
La presente garantía cubre este producto por 3 años contra cualquier defecto
de fabricación en sus materiales y mano de obra, bajo las siguientes
condiciones:
1. Todos los productos a que se refiere esta garantía, ampara su cambio físico,
sin ningún cargo para el consumidor.
2. El comercializador no tiene talleres de servicio, debido a que los productos
que se garantizan no cuentan con reparaciones, ni refacciones, ya que su
garantía es de cambio físico.
3. La garantía cubre exclusivamente aquellas partes, equipos o sub-ensambles
que hayan sido instaladas defábrica y no incluye en ningún caso el equipo
adicional o cualesquiera que hayan sido adicionados al mismo por el usuario
o distribuidor.
Para hacer efectiva esta garantía bastara con presentar el producto al
distribuidor en el domicilio donde fue adquirido o en el domicilio de IC Intracom
México, S.A. de C.V., junto con los accesorios contenidos en su empaque,
acompañado de su póliza debidamente llenada y sellada por la casa
80
vendedora (indispensable el sello y fecha de compra) donde lo adquirió, o
bien, la factura o ticket de compra original donde se mencione claramente el
modelo, numero de serie (cuando aplique) y fecha de adquisición. Esta
garantia no es valida en los siguientes casos: Si el producto se hubiese
utilizado en condiciones distintas a las normales; si el producto no ha sido
operado conforme a los instructivos de uso; ó si el producto ha sido alterado o
tratado de ser reparado por el consumidor ó terceras personas.
™
INTELLINET NETWORK SOLUTIONS offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com .
All products mentioned are trademarks or registered trademarks of their respective owners.
81