In order to facilitate capabilities of service personnel to replace certain parts or modules on PT-60 series, this chapter is providing assembly drawings of PT-60 series with related mechanical plus electrical connection details to serve this purpose.
For spare parts P/N and descriptions, please refer to Chapter 5 for more details.
Step-2> Pull out the top cover of PT-60 slowly to avoid damaging the Keypad FPC cable.
Step-3> Release the keypad FPC cable from J7 and LCD cable from J3 as shown in the picture at the left.
Doc. No.
1/7
Picture Step-4>
Step-5> Release CCD module FPC cable from SJ1 and vibrating motor cable from SCN1.
*Note: When Wifi antenna cable is plugged/unplugged from its connector, please take caution not to be overlapped with anything on Bluetooth antenna connector to avoid side effect on the antenna function.
Step-6: Pull out the PCBA from PT-60 bottom cover slowly and also remove the I/O pin board from J9.
*Note: Please be cautious on the orientation of I/O pin board when inserting, PCB side with 3-holes must be facing upward (PCBA top side) and the other side with 4-holes must be facing downward (PCBA bottom side) as shown in the picture below.
Doc. No.
2/7
Picture
Step Step-7: Remove 4 screws to release key lock and CCD module.
*Note: It is not necessary to remove the screw of the top side of vibrating motor cover.
SStep-8> Pull out vibrating motor and key lock from the case.
Step-9> Loose 3 screws on the back of scan module and scanning board can be taken out independently as shown in the picture.
Doc. No.
3/7
*Note: Be aware of the orientation of vibrating motor when pushing it back into its slot. You should be able to fit it in properly if matching the orientation of can match the direction of the motor rubber. Key lock assembly of PT-60 has a magnetic coil as shown in the picture whereas no magnetic coil is used in the key lock assembly of PT-20. PT-60 scan module has a speaker whereas there is no speaker in PT-20 scan module. PT-20 uses buzzer on main board to give audio messages.
Doc. No.
4/7
Item 1 2 3 4 5
Description PT-60 top cover module, including keypad module 2.4 color TFT LCD with T/P PT-60 /PT-6001Main Board PCBA Pogo module PT-60 CCD-1D scan module & Speaker PT-60 spring-STY PT-60 stylus-s
QTY 1 1 1 1 1
1 1 1
6 7
34-P6001-001 42-P6003-001
Doc. No.
5/7
Item 8 9 10 11 12 13 14 15
Part No. 90-P6001-001 47-P6001-001 35-P2001-001 90-P6003-001 23-21303-001 39-P2004-001 90-P2009-001 23-21201-002 PT-60 stylus PT-60 rubber-SD Shaft
Description
QTY 1 1 1 1 1 1 1 1
PT-60 base cover module Li-polymer battery PT-20 battery cover Pistol grip module Li-ion battery
Item 16 A B C D E
Description Pistol grip cover module SCREW T2 X 4 SCREW T1.7 X 5 SCREW M2.6 X 6 SCREW M2.6 X 10 SCREW M2.6 X 6
QTY 1 4 2 6 2 2
[Note]: The only difference among batch model, Bluetooh model and WiFi model is main board. Item Part No. 55-P6001-014 55-P6001-024 Description PT-6010 Main Board PCBA, w/BT PT-6020 Main Board PCBA, w/WiFi QTY
Item
QTY 1
Doc. No.
6/7
Item 1 2 3 4 5 6 A B
Part No. 39-P2006-001 40-P2004-001 55-P2003-001 40-P2005-001 39-P2005-001 34-21408-001 86-VG32K-4R0 86-VA524-100
Description PT-20 cradle top cover PT-20 Film-cradle F PT20/60 cradle main board OCBA PT-20 cradle File-B PT-20 cradle bottom Rubber-Foot Screw T2.6C4 Screw T3 x 10 NI 1 1 1 1 1 4 2 4
QTY
Doc. No.
7/7