GENERAL SPECIFICATIONS
Machine
Metric
English
15.7" x 15.7"
22"
25.2"
25.2"
3.1" - 28.3"
3.9" 29.1"
29.5 HP AC
106.3" x 160.7"
19,140 lbs.
24.8" x
Bed
Construction...............................................................................One Piece Meehanite Casting
Three (3) point support
Number of Guides X, Y & Z-axes.............................................2
Size of Guides X, Y & Z-axes.................................#55
Table (Z-Axis)
Time to full rapid.......................................................................
Distance to full rapid..................................................................60 mm
Rapid Traverse ........................................................................60 m/min.
Feedrate
........................................................................50 m/min.
Thrust Capacity (Duty).............................................................20 kN
Thrust Capacity (continuous).....................................................5.5 kN
Type of Drive ........................................................................AC Digital Servo Motor
Ball Screw Diameter..................................................................#45
Axis Motor
........................................................................5.5 kW (alpha series)
140 msec
2.4
2,360 ipm
1,968 ipm
4,496 lbs
1,236 lbs
7.4 HP
168 msec
3.54
2,360 ipm
1,968 ipm
2,698 / 3,372 lbs
202 / 899 lbs
6.0 HP
160 msec
3.1
2,360 ipm
1,968 ipm
4,496 lbs
1,236 lbs
6.0 HP
0.000100
0.000080"
0.000060"
0.000040"
Spindle Nose
........................................................................No. 40 Taper (HSK63A optional)
Tooling
........................................................................CAT V-flange (HSK63A optional)
Tool Clamp Force (mechanical)................................................9.8 kN (No. 40 taper)
2,200 lb.
Tool Clamp Force HSK63A...................................................18.0kN
4,050 lb.
Spindle Speed Range..................................................................Two Range, 50-14,000 RPM
Spindle Acceleration Time .......................................................(50 to 14,000 rpm)
1.7 sec / 1.6 sec
deceleration
(50 to 7,000 rpm)...........................0.5 sec / 0.5 sec deceleration
Spindle Orientation....................................................................Electric Servo Control
Drive Motor (4,000 ~ 10,000 rpm)
15 min ........................................................................26 kW AC
34.9 HP AC
Continuous...................................................................22.0 kW AC
29.5 HP AC
Torque Characteristics:
10% ED Rating (50 ~585 rpm).....................................302 N m
222 ft lb
25% ED Rating (50 ~865 rpm).....................................204 N m
150 ft lb
Continuous Rating (50-1,200 rpm)...............................119 N-m
87.7 ft lb
Obtain Full HP: ........................................................................4,000 rpm
Constant Torque Range...............................................................50 to 585 rpm
Spindle Bearing Design:
Front.............................................................................Two (2) Angular Contact Bearings with Ceramic Balls
Rear..............................................................................Two (2) Angular Contact Bearings Steel Balls and Rings
Bearing:
Inner Diameter.............................................................85 mm
3.35"
Outer Diameter............................................................130 mm
5.12"
Spindle Temperature Control.....................................................Oil Air Lubrication with Jacket Cooling,
Referenced to Bed
Rigid Tap...................................................................................2,800 RPM
Spindle Nose
........................................................................HSK63A only
Tooling
........................................................................HSK63A
Tool Clamp Force (mechanical)................................................18.0 kN (HSK63A)
4,050 lbs.
Spindle Speed Range..................................................................Two Range, 50-20,000 RPM
Spindle Orientation
.......................................................Electric Servo Control
Spindle Acceleration Time .......................................................(to 20,000 rpm)
2.8 sec / 2.4 sec
deceleration
Spindle Acceleration Time .......................................................(to 10,000 rpm)
0.6 sec / 0.5 sec
deceleration
Drive Motor
10 min ........................................................................18.5 kW AC
24.8 HP AC
Continuous...................................................................11 kW AC
14.8 HP AC
Torque Characteristics:
15% ED Rating (50 ~1,450 rpm)..................................98 N m
72 ft lbs
Obtain Full HP:...........................................................................6,000 rpm
Constant Torque Range...............................................................50 to 1,450 rpm
Spindle Bearing Design:
Front.............................................................................Two (2) Angular Contact Bearings with Ceramic Balls
Rear..............................................................................Two (2) Angular Contact Bearings Steel Balls and Rings
Bearing:
Inner Diameter.............................................................70 mm
2.76"
Outer Diameter............................................................110 mm
4.33"
Spindle Temperature Control.....................................................Core Cooled/Under race lubrication, Referenced to
Bed
Rigid Tap........................................................................4,000 RPM
Utility Requirements
Air:
Electrical Specification:
Volts
Phase
Cycle
kVA, Sum of All Equipment (std configuration)
Standard Transformer kit
Main Circuit Breaker
240V
480V
72 ~ 116 psi
14.4 cfm
23.3 cfm
240 or 480
3
60
50
65kVA
225 Amps
125 Amps
Tank Capacities
Hydraulic Tank ........................................................................22 Liters
Spindle Cooling Oil.....................................................................32 Liters
Spindle Lubrication Oil...............................................................1 Liter
Automatic Grease Supply Unit
Lube
........................................................................0.7 Liter
Home Positions
X-Axis
Y & Z-Axis
B-Axis
........................................................................Center of Stroke
........................................................................Stroke (+) End
........................................................................Edge Locator Parallel to X
5.8 gal.
8.4 gal.
0.26 gal
0.18 gal
Horsepower Curves:
Standard High Power Spindle:
Restrictions of Workpiece:
Limitation of Stroke:
Programming Method
Inch/metric selection (G20, G21) (5120A) (MM STD);
Custom Marco Common Variables: 82 (5282C) (MM STD);
Minimum increment: 0.0001 mm; 0.0001 in.
Maximum programmable dimension: 9 digits (99999.9999);
Absolute/Incremental programming (G90/G91);
Decimal point programming/Calculator type decimal point input;
Automatic recognition of EIA/ISO code;
Interpolation
Positioning (G00);
Linear interpolation (G01);
Circular interpolation (G02, G03);
Helical interpolation (Circular + 2 axis linear) (G02, G03);
Feeds
Cutting feedrate;
F-direct command;
Dwell (G04);
Rapid traverse override;
Cutting feedrate override (0-200%);
Feedrate override cancel (M49/M48);
I/O Devices
PCMCIA Card;
USB interface;
Data Center Internal Memory: 4MB
STM Functions
S-function direct command (direct spindle programming);
T-function;
M-function;
Tool Offsets
Tool length offsets (99 total) (G43, G44/G49);
Tool radius offset C (G41, G42/G40);
Tool offset memory Type A;
Coordinate Systems
Manual return to reference point;
Automatic return to reference point (G28);
Return to 2nd reference point (G30);
Reference point return check (G27);
Return from reference point (G29);
Coordinate system setting (G92);
Machine coordinate system setting (G53);
Work coordinate system selection (G54-G59);
Local coordinate system setting (G52);
Single block;
Program stop (M00);
Optional stop (M01);
Optional block skip 1 (/);
Dry run;
Machine lock;
Z-axis feed cancel;
Auxiliary function lock;
Mirror image (M21, M22/M23);
Manual absolute;
Tool length measurement (manual);
Help function;
Installation
Environmental conditions for machine run-off at Makino are controlled to the following level:
Temperature
Fluctuation
Humidity
Dust
Air Supply
Warm 40C
104F
Cool
10C
50F
1C/30 min.
1.8F/30 min.
35 ~ 70%
Not applicable
72-115 psi and 15.9 cfm (23.3 cfm with optional air blow) of DRY air supplied through a
minimum supply pipe of 3/4" diameter with no reducers or nozzles.
NOTE: The base machine configuration, specifications and pricing may be changed without prior notice to
incorporate improvements resulting from ongoing R&D programs
The quoted accuracies are attained through proper application of environmental conditions, and suitable
industrial floor for machine stability.
This document is the confidential intellectual property of Makino Inc and must be
surrendered upon demand.