Perform steps 1 5 for a Measure Match (Sweep) test. Perform steps 6 10 for a Fault Location (DTF) test. Perform steps 11, 12, and 13 to measure RF power. Refer to the instruction manual for details. System information to have ready before you begin...
4 Frequency Span 4 Cable Type 4 Approximate Cable Length
Freq.
TM
1 3
Set the scale for optimal viewing. Set up the limit line if desired.
Scale
est. match t for easure m rse side ncy for on reve art eque stem fr from ch Enter sy cy span equen Enter fr t. DTF tes Start
8 5 2
9 6 3 +/-
Or
4
1
&
Enter
Press Escape in save mode to remove a recalled trace from the display without deleting it.
, Or
238, 475, 949
Enter
7 4
1
8 5 2
9 6 3 +/-
5 soThe unique
&
Enter
regis me label applicatio tration nu for m n m ore d s. Enter a ber is en ough n alp etaile h d ide ntific anumeric for ation .
Delete
Auto Units
Enter
accurate 2 Calibration is the key touseful test measurements and results. Dont forget this step. And 7
Cali
at e br
Disp
7 8 5 2 9 6 3 +/-
,
4
1
Enter
And
Move column
10 8
Distance Scale
Or
&
Enter
Enter
Set the cable type and select units. Set the start and stop distance and set the scale for optimal viewing. Set up the smoothing and limit line if desired.
7 8 5 2 9 6 3 +/4
Attach each standard at the point the antenna will be tested, and press the corresponding key. There will be a beep to indicate the calibration is complete for that standard.
Short
Load
Enter
Save label
Utility
Print Setup
Start Stop
Or
&
Enter
, Save/Recall
Space
, Meters Feet , Or
238, 475, 949
Enter
7 4
1
Enter
8 5 2
9 6 3 +/-
&
Enter
, Auto
Units Disp
7 8 5 2 9 6 3 +/-
, ,
4
1
Enter
Escape
Enter
, Or ,
Enter
The escape key allows you to back up one menu level and to exit a setting
11
and units.
&
Enter
PwrUnit Watts/KWatts/dBm
Caution +22 dBm max input Do not apply RF power to the Antenna Test Port.
Mode
13
8 5 2
9 6 3 +/-
, Or
4
1
&
Enter
Mark On/Off/Active
System
(Time/Date)
Off/Active
8 5 2
9 6 3 +/-
Printer
Type
Off = Mark not displayed Active = Mark can be moved using cursor keys or numeric keypad.
&
Enter
Triangle/Line
FM Mod
On/Off Delta
Electronic Corporation
30303 Aurora Road Cleveland (Solon), Ohio 44139-2794 Phone: (440)248-1200 Fax: (440)248-5426 http://www.bird-electronic.com
Form No.: 920-SAT-REF Rev H Copyright 2005 Bird Electronic Corporation Printed in the U.S.A.
Rtn to Defaults
Single Mode / Dual Mode
Screen Description
Mode Indicator Recalled Trace Name Marker Cursor Battery Gauge Soft Key Description Trace
Save/ Recall
Component Description
Mode Keys Mode: Activate mode menu Config: Activate configure menu for selected mode Calibrate: Activate calibration menu Marker: Activate marker menu Soft Keys Activate the function described directly to the right of the key
Velocity Percent Freq Span (MHz) 25 50 75 100 200 300 400 500 600 700 800 900 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 5975
[238 Pts]
M1
VSWR (0.00/ )
Auto Scale
Numeric Keypad
DC Input
Limit Test On
M2
Run
1.00
825.00
Print Limit: 1.43 FAIL M1: 835.20 MHz 1.64 M2: 831.50 MHz 1.20
MHz
Calibration: Full
841.00
Marker Value
Limit Line
Status Indicator
Primary Measurement
Fwd
PwrUnit Watts MatchUnit Rtn Loss Mode APM
Refl Match 0.00 Watts 0.00 Loss(dB)
0.0 Watts
600.00
Primary Value Full Scale
Enter Select item Exit data entry and change the value Test Port Connect to antenna
Frequency Span (MHz) = Stop Frequency (MHz) - Start Frequency (MHz) Distance (ft) = Velocity of Propagation (Vp) x 117,000 / Frequency Span (MHz) Resolution (in) = Distance (ft) x 12 / (238 Data Points - 1) Distance (m) = Velocity of Propagation (Vp) x 35,500 / Frequency Span (MHz) Resolution (cm) = Distance (m) x 100 / (238 Data Points - 1) Note: Maximum Distance is 999.9
Escape Back up one menu level Exit date entry without changing the value
Power LEDs Green lit: Power on Yellow blinking: Battery pack is charging
Secondary Measurements
Secondary Values
Cursor Keys Navigate during data entry Move markers one point at a time (left & right) Move markers to the minimum or maximum (up & down)