Anda di halaman 1dari 3

SEND-DTSCONNECT-MESSAGE (0E HEX)

A Send-Disconnect-Message command may be termi-


The Send-Disconnect-Message commandis a Target- natedby Iffi assertedwhen HA=1,or when a Discon-
role commandwhich may be used to disconnectfrom
nector Resetcommandis issued.
the SCSI bus at any time during a SCSI command
sequence.This commandconsistsof sendinga Discon- The followingtablesummarizesthe possiblevaluesthat
nect messagebyte,followedby physicaldisconnection the COMMAND PHASE registercan take during the
from the bus (SCSI bus free). An interruptis generated Send-Disconnect-Message, andtheirmeaningsrelative
only after transitionto bus free occurs.As an option,a to commandtermination.See other @mmand descrip-
Save-Data-Pointer messagewill automaticallybe sent tions lor additional values that can occur when
beforethe Disconnectmessagewheneverthe lDl bit is commandchainingis used.
set priorto issuingthis command.
Command
The COMMAND PHASE register is updated during Phase Meanlng
executionol the Send-Disconnect-Message command
No operation occurred; typically, ATN was
to indicatebus phase status.Atter a Save-Data-Pointer
found to be asserted.
messageis sent,the COMMANDPHASEwill be set to
41 The Save-Data-Pointermessage was trans-
41H. Afterthe Disconnectmessagetransfer,this regis- ferred.
ter will be updatedto 42H, and after disconnectionthe 42 The Disconnectmessagewas transferred.
COMMANDPHASEregisterwill containa 43H. 43 The bus free state occurred after the Discon-
nect messagewas transferred.The 33C93A is
now in the disconnectedstate.

ELECTRICALCHARACTERISTICS
ABSOLUTEMAXIMUMRATINGS
Vohageon any pin with respectto GND -0.5 V to +7.0 V
Operatinglemperature 0 to 70 deg. C
Storagetemperature -55 to +125 deg. C
Power dissipation 500 mW
Input Static DischargeProtection 2000 V pin to pin

Sfrasses above those listed under ABSOLUTE MAXIMUM


RATINGSmay cause permanent device failure. Functionality
at or above these limitsis not implied. Expsure to absolutely
matrlmum ratings for extended periods may affect device
reliability.

DC OPERATING
CHARACTERISTICS
Ta - 0 to 70oC,VCC - +5 V t0.25 V, GND = 0 V

Symbol Characterlstlc Mln Max Unlts Condltlons

ilL Input Leakage pA VIN-. 4 to VCC


toLl pA VOUT- .5 to VCC
lo12 ['n VOUT= .4 to VCC
VIH V
VIL V
VIHYS V

VOH V lO - -400 ttA


VOLl Voltage 0.5 V lO = 48.0 mA
VOL2 Voltage (All Others) 0.4 V lO = 4.0 mA
tcc 20 mA Ta = +25oC

4-60 Am33G93A
SWITCHINGTESTCIRCUIT

From output
undertest

Pins of the Devlce

INTRO 1 0 0p F 4mA 400pA

lffiffituffiffiffiffiffiffi.
BSY,SEL,UO,CID
MSG,ATN,REQ,ACK
100pF 20 mA

' Actual
capacitancemay vary *2Oo/o.

SWITCHINGTESTWAVEFORM
All the Open Dralns

t-
.ru

All OtherPlns

Am33C93A 4€1
TIMING CHARACTERISTICS Where:
Timingcharacteristicsare validoverthe entireoperat-
ingtemperature (0to 70"C)andvoltage(4.75to 5.25V) Tcycis the internalclockcycletime;
ranges,andarereferenced to andlroma lowvoltageof Tckinis theperiodof theclockat the CLKinput;
0.8voltsanda highvoltageof 2.0Volts.All outputsare
assumedto havea loadcapacitance of 100picofarads. DIVISOR is theclockdivisorselectedin the OWNlD
register.
Manyol thetimingparameters thatfollowaredeiinedin
termsof an internalclockcycletimethat is determined Forexample, witha 16 MHzclockinputto the33C93A,
by the inputclockandthe clockdivisorselectedin the the clockdivisorselectedwouldbe 4. Therefore,the
OWN lD register.This cycle time is calculatedas valueof Tcycwouldbe:
follows:
62.5rls. 4
Tckin.DIVISOR Tcyc= =125ns
Tcyc= Z
2

lnterface
Processor/DMA

CLK
Symbol Charac{erlstlc Mln Max Unlts
tcp Clock Period 16MHz 62.5 125 ns
20 MHz 50.0 ns
t"t Clock High 16MHz 28.0 ns
20 MHz 20.0 ns

11853-014A

4-62 Am3ilCll3A

Anda mungkin juga menyukai