Anda di halaman 1dari 7

TSOP341.., TSOP343..

Vishay Semiconductors

IR Receiver Modules for Remote Control Systems


FEATURES
Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V
1 2 3
16672

Improved immunity against ambient light Insensitive to supply voltage ripple and noise Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC

MECHANICAL DATA
Pinning: 1 = OUT, 2 = GND, 3 = VS

DESCRIPTION
The TSOP341.., TSOP343.. series are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TSOP341.. is compatible with all common IR remote control data formats. The TSOP343.. is optimized to better suppress spurious pulses from energy saving fluorescent lamps but will also suppress some data signals. This component has not been qualified according to automotive specifications.

PARTS TABLE
CARRIER FREQUENCY SHORT BURSTS AND HIGH DATA RATES (AGC1) NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3) 30 kHz 33 kHz 36 kHz 38 kHz 40 kHz 56 kHz TSOP34130 TSOP34133 TSOP34136 TSOP34138 TSOP34140 TSOP34156 TSOP34330 TSOP34333 TSOP34336 TSOP34338 TSOP34340 TSOP34356

BLOCK DIAGRAM
16833

APPLICATION CIRCUIT
17170_5

3 30 k VS 1 Input AGC Band pass Demodulator OUT

R1 IR receiver VS + VS C1 OUT GND VO C GND

Transmitter with TSALxxxx

2 PIN Control circuit GND

R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 < R1 < 1 k, C1 > 0.1 F.

Document Number: 81737 Rev. 1.3, 29-Jan-09

Circuit

www.vishay.com 115

TSOP341.., TSOP343..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems

ABSOLUTE MAXIMUM RATINGS (1)


PARAMETER Supply voltage (pin 3) Supply current (pin 3) Output voltage (pin 1) Output current (pin 1) Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tamb 85 C t 10 s, 1 mm from case TEST CONDITION SYMBOL VS IS VO IO Tj Tstg Tamb Ptot Tsd VALUE - 0.3 to + 6.0 3 - 0.3 to (VS + 0.3) 5 100 - 25 to + 85 - 25 to + 85 10 260 UNIT V mA V mA C C C mW C

Note (1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating condtions for extended periods may affect the device reliability.

ELECTRICAL AND OPTICAL CHARACTERISTICS (1)


PARAMETER Supply current (pin 3) Supply voltage Transmission distance Output voltage low (pin 1) Minimum irradiance Maximum irradiance Directivity Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 250 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Angle of half transmission distance TEST CONDITION Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight SYMBOL ISD ISH VS d VOSL Ee min. Ee max. 1/2 30 45 0.1 2.5 45 100 0.25 MIN. 0.27 TYP. 0.35 0.45 5.5 MAX. 0.45 UNIT mA mA V m mV mW/m2 W/m2 deg

Note (1) T amb = 25 C, unless otherwise specified

TYPICAL CHARACTERISTICS
Tamb = 25 C, unless otherwise specified
Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms)
0.4

Ee

tpo - Output Pulse Width (ms)

0.35 0.3 0.25 0.2 0.15 Input Burst Length 0.1 0.05 0 0.1 = 950 nm, optical test signal, fig. 1 1 10 100 1000 10 000 Output Pulse Width

tpi *) T *) tpi 6/fo is recommended for optimal function

Output Signal VO VOH VOL td1 )


1) 2)

14337

3/f0 < td < 9/f0 tpi - 4/f 0 < tpo < tpi + 6/f0 t

tpo2 )

20760

Ee - Irradiance (mW/m)

Fig. 1 - Output Active Low www.vishay.com 116

Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Document Number: 81737 Rev. 1.3, 29-Jan-09

TSOP341.., TSOP343..
IR Receiver Modules for Remote Control Systems

Vishay Semiconductors

Ee

Ee min. - Threshold Irradiance (mW/m)

Optical Test Signal

4 Correlation with Ambient Light Sources: 3.5 10 W/m = 1.4 klx (Std. illum. A, T = 2855 K) 10 W/m = 8.2 klx (Daylight, T = 5900 K) 3 2.5 2 1.5 1 0.5 0 0.01 Wavelength of Ambient Illumination: = 950 nm

600 s t = 60 ms Output Signal, (see fig. 4)

600 s

94 8134

VO VOH VOL

t on

t off

t
20745

0.1

10

100

Ee - Ambient DC Irradiance (W/m)


Fig. 6 - Sensitivity in Bright Ambient

Fig. 3 - Output Function

Ton, Toff - Output Pulse Width (ms)

Ton 0.7 0.6 0.5 Toff 0.4 0.3 0.2 0.1 0 0.1 = 950 nm, Optical Test Signal, Fig. 3 1 10 100 1000 10 000

Ee min. - Threshold Irradiance (mW/m)

0.8

1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 1 10 100 1000 f = 30 kHz f = f0 f = 20 kHz f = 10 kHz f = 100 Hz

20744

Ee - Irradiance (mW/m)
Fig. 4 - Output Pulse Diagram

20746

VsRMS - AC Voltage on DC Supply Voltage (mV)


Fig. 7 - Sensitivity vs. Supply Voltage Disturbances

1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.7


16925

500

E e min./Ee - Rel. Responsivity

E - Max. Field Strength (V/m)

450 400 350 300 250 200 150 100 50 0

f = f0 5 % f(3 dB) = f0/10

0.9

1.1

1.3

0
20747

500

1000

1500

2000

2500

3000

f/f0 - Relative Frequency

f - EMI Frequency (MHz)

Fig. 5 - Frequency Dependence of Responsivity

Fig. 8 - Sensitivity vs. Electric Field Disturbances

Document Number: 81737 Rev. 1.3, 29-Jan-09

www.vishay.com 117

TSOP341.., TSOP343..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems

1 0.9

10

20 30

Max. Envelope Duty Cycle

0.8 0.7 0.6 0.5 0.4 0.8 0.3 0.2 0.1 0 0 f = 38 kHz, Ee = 2 mW/m 20 40 60 80 100 120 0.6
96 12223p2

40 1.0 TSOP341.. 0.9 50 60 70 0.7 80

TSOP343..

0.4

0.2

0.2

0.4

0.6

20761

Burst Length (number of cycles/burst)

drel - Relative Transmission Distance


Fig. 12 - Horizontal Directivity

Fig. 9 - Maximum Envelope Duty Cycle vs. Burst Length

Ee min. - Threshold Irradiance (mW/m)

0.2 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 - 30 - 10 10 30 50 70 90

0.2 0.18

Ee min. - Sensitivity (mW/m)

0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 2 2.5 3 3.5 4 4.5 5 5.5 6

20749

Tamb - Ambient Temperature (C)

20750

Vs - Supply Voltage (V)


Fig. 13 - Sensitivity vs. Supply Voltage

Fig. 10 - Sensitivity vs. Ambient Temperature

1.2

S ( ) rel - Relative Spectral Sensitivity

1.0 0.8 0.6 0.4 0.2 0.0 750 850 950 1050 1150

16919

- Wavelength (nm)

Fig. 11 - Relative Spectral Sensitivity vs. Wavelength

www.vishay.com 118

Document Number: 81737 Rev. 1.3, 29-Jan-09

TSOP341.., TSOP343..
IR Receiver Modules for Remote Control Systems
SUITABLE DATA FORMAT
The TSOP341.., TSOP343.. series are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP341.., TSOP343.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: DC light (e.g. from tungsten bulb or sunlight) Continuous signals at any frequency Modulated noise from fluorescent lamps with electronic ballasts (see figure 14 or figure 15)
16920

Vishay Semiconductors

IR Signal

IR Signal from Fluorescent Lamp with Low Modulation

10

15

20

Time (ms)
Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation

IR Signal from Fluorescent Lamp with High Modulation

IR Signal

0
16921

10

10

15

20

Time (ms)
Fig. 15 - IR Signal from Fluorescent Lamp with High Modulation

TSOP341.. Minimum burst length After each burst of length a minimum gap time is required of For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second Recommended for NEC code Recommended for RC5/RC6 code Recommended for Sony code Recommended for RCMM code Recommended for r-step code Recommended for XMP code Suppression of interference from fluorescent lamps 6 cycles/burst 6 to 70 cycles 10 cycles 70 cycles > 1.2 x burst length 2000 yes yes yes yes yes yes Common disturbance signals are supressed (example: signal pattern of fig. 14)

TSOP343.. 6 cycles/burst 6 to 35 cycles 10 cycles 35 cycles > 6 x burst length 2000 yes yes no yes yes yes Even critical disturbance signals are suppressed (examples: signal pattern of fig. 14 and fig. 15)

Note For data formats with long bursts (more than 10 carrier cycles) please see the data sheet for TSOP348.., TSOP344.

Document Number: 81737 Rev. 1.3, 29-Jan-09

www.vishay.com 119

TSOP341.., TSOP343..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems

PACKAGE DIMENSIONS in millimeters


6 3.9

8.25

30.5

0.5

(5.55)

6.95

5.3

0.85 max.

0.89

OUT

GND

VS 0.5 max. 2.54 nom.

1.3

0.7 max. 4.1

2.54 nom.

5.6

Marking area

Not indicated tolerances 0.2

technical drawings according to DIN specifications

Drawing-No.: 6.550-5169.11-4 Issue: 13; 17.12.08


16003

R 2.5

www.vishay.com 120

Document Number: 81737 Rev. 1.3, 29-Jan-09

Legal Disclaimer Notice


Vishay

Disclaimer
All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishays terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners.

Document Number: 91000 Revision: 18-Jul-08

www.vishay.com 1

Anda mungkin juga menyukai