Anda di halaman 1dari 15

DBS3900 Upgrade to V100R009C00SP88

1, Project: Only for LCLS Trial 2, Target: Upgrade DBS3900 to V100ROO9C00SP88 3, Requirement list: Laptop, UTP cable,DBS3900 hardware, software and upgrade guide from support or HUAWEI engineer. DBS3900 Hardware Software and Upgrade guide 4, Precondition: Installation finished; BBU and RRU power on; BBU and RRU connection is ready. Connetct GTMU and RRU from CPRI0 to CPRI5 one by one. For example : 2 RRU will connect CPRI0 and CPRI1; 3 RRU will connect CPRI0,CPRI1 and CPRI2;4 RRU will connect CPRI0,CPRI1,CPRI2,and CPRI3. 5, Upgrade Procedure 5.1 Extract BTS3900 V100R002C00SPC130 Version(GBTS V100R009C00SPC088).zip and BTS3900 V100R002C00SPC130 Version Documents-EN.zip until get the upgrade guide BTS3000V100R009C00SPC088 Upgrade Guide (SMT-Based).doc , upgrade tool btsm.exe and downloading file gtmudown.pck and mrrudown.pck. 5.2 Configure computer IP with 192.168.0.X excluded 192.168.0.72 because 192.168.0.72 is GTMU fix commissioning IP. 5.3 Connect computer and ETH port of GTMU. Open btsm.exe and put 192.168.0.72, click ok. 5.4 Get site management right. Select Get. BBU with GTMU; MRRU BTS3900 V100R002C00SPC130 Version(GBTS V100R009C00SPC088).zip BTS3900 V100R002C00SPC130 Version Documents-EN.zip

2011-9-22

1 , 15

Click board( left tree)--->board management, you can see GTMU. If you can not check, click refresh

2011-9-22

2 , 15

Right click GTMU, select Board information

Check the current software version and save it.

2011-9-22

3 , 15

Download GTMU FILE Click site0 on left tree, then click force software load

2011-9-22

4 , 15

File Name: Specify the path and name of the target software package required for the upgrade. Send Window Size: 200 Version: Type V100R009C00SP88 in the lower box. File ID: Select GTMU_MAIN from the drop-down list.

2011-9-22

5 , 15

Click start

When the progress bar displays "100%" in the lower corner and the status bar displays "Loading Software Successfully", click Close. If fail , please download again.

Download MRRU FILE ClickForce software download again

File Name: Specify the path and name of the target software package
6 , 15

2011-9-22

required for the upgrade.


Send Window Size: 200 Version: Type V100R009C00SP88 in the lower box. File ID: Select MRRU_MAIN from the drop-down list.

When the progress bar displays 100% and the status bar displays "Loading Software Successfully", click Close. If fail, please download again.

After 5 minutes, Active MRRU FILE

2011-9-22

7 , 15

On the SMT, click Site255 in the navigation tree, and then double-click Software Activation under Function. In the displayed dialog box, set the associated parameters as follows:

Version: V100R009C00SP88. In the File ID drop-down list, click MRRU_MAIN.

Click OK. The software activation starts. When the progress bar displays 100% and the status bar displays "Software Activation Confirmed", click Close.

Active GTMU FILE On the SMT, click Site255 in the navigation tree, and then double-click Software Activation under Function. In the displayed dialog box, set the associated parameters as follows:

Version: Type V100R009C00SP88 in the lower box. File ID: Select GTMU_MAIN from the drop-down list. Board No.: You are not required to set this parameter.

Click OK. The software activation starts. When the status bar displays "Activation is confirmed and the Site will be reset in a few minutes", click Close.

2011-9-22

8 , 15

After 10 minutes ,Select Board-->Board Management, right click GTMU, then click board reset

6,Configuration for MRRU downloading After GTMU board reset, you can connect computer to GTMU again.

6.1 Get site management right. 6.2 Click Board--->Board Configuration


2011-9-22 9 , 15

Double click GTMU, then can config RRU.

Click Add RRU

2011-9-22

10 , 15

Configure MRRU, for example, the site has 4 MRRU, please configure 4 MRRU one by one: MRRU0(which connect to CPRI0): Card Type:MRRU; Card No:0; Chain N0:0; Hop:1; Shelf No:60; Port:0 MRRU1(which connect to CPRI1): Card Type:MRRU; Card No:1; Chain N0:1; Hop:1; Shelf No:61; Port:1 MRRU2(which connect to CPRI2): Card Type:MRRU; Card No:2; Chain N0:2; Hop:1; Shelf No:62; Port:2
2011-9-22 11 , 15

MRRU3(which connect to CPRI3): Card Type:MRRU; Card No:3; Chain N0:3; Hop:1; Shelf No:63; Port:3 (Green is meaning the RRU software is same with GTMU.)

6.3 After configure MRRU, open software activation(site0--->software activation),just check, you can select file ID to MRRU_MAIN.Dont need to click. Show the process of downloading MRRU file. When downloading finish, you will see Board downloading complete

2011-9-22

12 , 15

Also you can check the light of MRRU,the light of RUN will flash per 0.125s. After downloading, MRRU will reset automatically. You can check the light of MRRU, if MRRU reset, all lights will power off and power on.

6.4 Check GTMU software version. And confirm the software version is V100R009C00SP88.

2011-9-22

13 , 15

6.5 After software verification, reset GTMU.

Importatnt: 1, Must confirm GTMU file and MRRU file already are downloaded in GTMU. If can not make sure, can do it again.
2011-9-22 14 , 15

2, Must be clear the connection from GTMU to each MRRU and tell it to support team. 3, Two option can show MRRU upgrade successfully. First, open software activation and get the picture like below:

Sencond: if you can see MRRU reset after MRRU configuration, the light of MRRU power off and power on, it is meaning upgrade ok. 4,after finish all the work, Must do the board rest in order to delete all the configuration of MRRU.

2011-9-22

15 , 15

Anda mungkin juga menyukai