, LTD LM339
QUAD DIFFERENTIAL COMPARATOR
SOP-14
DESCRIPTION
The UTC LM339 consists of four independent voltage comparators, designed specifically to operate from a single power supply over a wide voltage range.
TSSOP-14
FEATURES
*Signal or dual supply operation. *Wide operating supply range (Vcc=2V~36V). *Input common-mode voltage includes ground. *Low supply current drain IF=0.8mA (Typical). *Open collector outputs for wired and connection. *Low input bias current IBIAS=25nA (Typical). *Low output saturation voltage. *Output compatible with TTL, DTL, and CMOS logic system.
DIP-14
ORDERING INFORMATION
Normal LM339-S14-R LM339-P14-R LM339-D14-T Ordering Number Lead Free Plating LM339L-S14-R LM339L-P14-R LM339L-D14-T Halogen-Free LM339G-S14-R LM339G-P14-R LM339G-D14-T Package SOP-14 TSSOP-14 DIP-14 Packing Tape Reel Tape Reel Tube
1 of 7 QW-R104-001.H
LM339
PIN CONFIGURATION
2 of 7 QW-R104-001.H
LM339
BLOCK DIAGRAM
Vcc
IN (-)
OUT
IN (+)
GND
3 of 7 QW-R104-001.H
LM339
ABSOLUTE MAXIMUM RATINGS (Ta=25C)
PARAMETER Supply Voltage Differential input Voltage Input Voltage SYMBOL Vcc VI(DIFF) VIN
RATINGS UNIT +- 18 or 36 V 36 V -0.3~36 V DIP-14 760 mW Power Dissipation PD SOP-14 560 mW TSSOP-14 440 mW Junction Temperature TJ 125 C Operating Temperature TOPR -20 ~ +85 C Storage Temperature TSTG -40 ~ 150 C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied.
ELECTRICAL CHARACTERISTICS
(Vcc=5.0V, Ta=25C, All voltage referenced to GND unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS VCM=0 ~ Vcc-1.5 Input Offset Voltage VI(OFF) VOUT(p)=1.4V, Rs=0 Input Offset Current II(OFF) Input Bias Current IBIAS Input Common-Mode Voltage VIN(R) Range RL= Supply Current Icc Large Signal Voltage Gain GV Vcc=15V, RL>15k VIN=TTL logic wing Large Signal Response Time tres VREF=1.4V, VRL=5V, RL=5.1k Response Time tres VRL=5V, RL=5.1k Output Sink Current ISINK VIN (-)>1V, VIN (+)=0V, VOUT(p)<1.5V Output Saturation Voltage VSAT VIN (-)>1V, VIN (+)=0V, ISINK=4mA VIN (+)=1V,VIN (-)=0 VOUT(p)= 5V Output Leakage Current ILEAK VOUT (p)=30V Differential Input Voltage VIN(DIFF) MIN TYP. +-1.5 +-2.3 57 0 50 1.1 200 350 6 1400 18 140 0.1 1.0 36 MAX +-5.0 +-50 250 Vcc-1.5 2.0 UNIT mV nA nA V mA V/mV ns ns mA mV nA A V
400
4 of 7 QW-R104-001.H
LM339
TYPICAL CHARACTERISTICS
Fig.1 Supply Current
2.2 2.0 Ta=-40
Ta=-25 Ta=25
1.8
90 80 70 60 50 40 30 Ta=25 Ta=-25
Ta=70
Ta=70
RL=
20 10 30 35 40 0 5 10 15
Vcm=0VDC Rcm=1G 20 25 30 35 40
20
25
Supply Current (V) Fig.4 Reponse Time For Various Input Overdrive Negative Transition
Input Voltage (mV)
Ta=25 0 -100
Saturation Voltage(V)
-1 10
Input Overdrive
5.0mV
1.2
1.6
Time ( s)
Ta=25 100 0
Input Overdrive
50mV 20mV 5.0mV
Time ( s)
5 of 7 QW-R104-001.H
LM339
TYPICAL CHARACTERISTICS(cont.)
Fig.6
450
3 2 1 0
RL=2k Vcc=15V
400
350
3 2 1 0 0 10
300 275 50 0 1 2
20 30 Time ( s)
Time ( s)
100k 1k Vi +7V
+15V
Ta=25
6
Vcc
2k
5 4
Vcc/2
Vo Io
10
3
2
0
10
3
1 10
4
10
10
10
-3
10
-2
10
-1
10
10
Frequency (Hz)
Vcc=+5V
-1
Vcc=+15V Vcc=+30V
Vcc/2
10
Vcc Vo Io
40
20
10
-3
10
-2
10
-1
0 -50 -25
10
10
25
50
75
100
Temperature ()
6 of 7 QW-R104-001.H
LM339
UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
7 of 7 QW-R104-001.H