>
>1)Youngs modulus of mild steel
> 2.2* 10^6kg/cm2
>2)rod of dia(given)length(given)subjected to
>stress(given) and "E"(given).
> what is increase in length.
> 0.2cm
>3)centipose is unit of...........
> viscosity
>4)hardness is measured in
> brinell no.
>5)steady rest is used in.......
> i) milling ii)lathe (2 more option)
>ans- lathe
>
>6)rotating cutter and sliding w/p(process is)
> i)milling ii)shaping iii)swaging 7)maxm deflection of beam supported at
>two ends and
>loaded at centre
>8)cantilever beam failure occurs at ......
> support
>9)what type of fit is H9f9
> i)interference fit ii)shrink fit...etc.
>10)surface finish is represented by....
> i)square ii)circle iii)rectangle ....none of these
>11)broaching is done to produce....
> i)internal keyway ii)splines...(2 more options)
>12)twist drill is specified by
> i)lip angle,dia
> ii)lip angle , material,dia
> iii)dia ,shank, material
>13)in diesel engine.. injection occurs ..
> i)20degree btdc
> ii)20 degree atdc
> iii)12 degree atdc...
>14)in 4-stroke engine ratio of cam shaft and crank
>shaft rotation i)1:2 ii)2:1 ....etc
>15)two gears ...one(driving) at 100 rpm and other 300
>rpm....driven has m=4 and no. of teeth 60
> distance b/w centre is....
>16)reduction ratio ofspur gear
> i)1:4 ii) 1:20 iii)1:10.....
>17)cemented carbide tool is used at.....
> low , medium , high or all speed
>18)hardness signify....resistence to.
> scratching machining
> etc 19)coefficient of friction between cast iron and mild
>steel....
> i)0.2 ii) 0.3 iii) 0.001 etc.
>20)in SAW arc is struck under flux
> i)to prevent oxidation..(3 more options)
>21)which test is used for non ferrous material weld
>...
> magnetic particle test
>22)clutch is located between.....
> engine and gear box
>23)thermal efficiency of diesel engine is....
> i)less than 20% ii)less than 30%...etc
>24)in CI engine injection takes place ...
> at the end of compression stroke
>25)clearence volume(given)...suction volume(given)
> what is compression ratio.
>26)what type of sress is hertz stress.
> i)tensile ii) shear iii)contact....
>27)two helical spring is arranged in parallel ...the
>stiffness is ans- sum of stiffness
>28)99% tolerance is
> ans- < 3* (sigma)
>
>29)two cube ..one is half submerged and other is 2/3
>submerged ….
> Ratio of their densities….
>Ans -3:4
>
>30)for ammonia HP per tonn of refrigeration
>
>31) model of pump of 20 HP ….rotates at 400 rpm (head
>is 20m)
> find out speed when head is 60 m( given model dia
>is ¼ of original)
hi friends,
this mail is the continuation of the previous
mail OF TELCO.
aptitude section
be fast as questions really need time
#2 questions from series completion----- answer of
one of which is 60
one completion of series of alphabets answer was
bab
#1 question was that if x* is greatest integer less
then that number then to find the value of the
sequence answer was 6
#1 question in which relation between x an y are
given in form of series of numbers, guess the relation
between x and y and complete the series
#1 question in which two linear equation was given, in
terms of variables x,m,z,y then to find the coorect
choice--- choices comprise of other relation between
the parameters
#1 question in which a ratio of a mixture composition
made of cement and some other materials was
given....to find the amount of cement
needed.......answer was 45
#2 or 3 simple question based on percentage and profit
and loss
#1 question based on BODMAS rule...... answer was
.0012
#1 question in which a square was inscribed in a
circle to find the area of square answer was
2a^2
#1 question in which it was given that x<y then which
will be greater than x but less than y answer was
( x+y)/2
#1 question in which relation between g[x] and f[x]
was given then to find the relation between them is to
be found---------- confirm there is a correction in
this question so ask from them
#1 simple question based on time and distance
#2 question based on coding-decoding the trick of
first question was the two alphabets before the
alphabet of first word was the last alphabet of second
word the trick of second wasthe position of
alphabet in terms of no. (like A=1)from beginning and
from the end varies alternately
PASSAGE
a long passage was there based on principle of
induction that a shopkeeper offerd an apple to the
writer.....it was green and sour then he offers
another one which was also green and sour then when
the writer was offered the third one which was also
green he deducted that it is also sour so was then
discussed the nature of humanbeing to accept the
inference from induction.
then there was 5 to 6 question based on the passage
answer of 1 question was writer is from...... india
another one......... writer is a scientist
another one........apple has been used as ....... an
object of passage
question that what does "natural law" means........
answer is most probably...... induction
question that what does "extensive reference" means
question in which two statements was given and a
conclusion made on basis of them was given........it
represents syllogism
# quex. based on jigs and fixtures
# quex. based on carbon content in die steel
# return mechanism is not used in ....a . bore b.
planar ...
#what does 123+ .5 represents...
#angles r in the ratio 1:2:2... then the triangle
is.... isosceles
# distance between a &c is 60, a&b is 50 and b&c is
50.... find the shortest distance from pt. b on line
ac..... ans. 40 km.
ARRANGING QUESTIONS...
a question of arranging a series of mechanical
instruments on the side of a wall ...they were seven
in number........name of mechanical instruments was
given just to confuse you...... take the instruments
as lathe(l), polisher(p), air conditioner(a), H, B, D,
S
conditions... # lathe must always be at position 2
a&h must be together, s can stay with either b or
d.., lathe and polisher must not be adjacent...
# deduction... p can either be at 5 or 7(two questions
on this)
5 more questions on the above conditions
....... it is a simple question of arranging it.......
there were 5 to 6 question based on it
-----------------------------------------------------------------------
SOME MORE APTI QUESTIONS(SOME OF THEM MIGHT BE SAME)
APTITUDE:
1.0.0024/.012*.006=
2.A square is inscribed in a circle , radius of the
circle is 'a'.Area of the square=
Ans:2a^2
3.The angle of a triangle is 1:2:2 then the triangle
is
Ans:isosceles
4.X's salary is 150% of Y, and Z's salary is 75% of Y,
their total salary is
Ans:1000
5.g[x]=1+x/2, then value of g[2x] in terms of g[x] is
6.If X<Y ,which of the following is greater than X and
less than Y
Ans:sqrt(X*Y)
7. For the sequence 4,8,6,18,15,.....,the next number
is
8.to find the relationship between X & Y for the given
value
ans:4X+2=Y
9.(X*) is the largest integer but less than X.find the
value of (5.2*) + (4*)-(2*)=?
Ans:6
10. Series of An is given by (An-1)^3,if first value
of An is 1 find the series up to four steps
Ans:0,-1,-8,-729
11.Simple questions based time and distance
12.In a city 90% people has car, 15% has motorcycle,
100% has car or motorcycle then how many of them have
only car and motorcycle.
13.Two problems are based upon coding
14.There was a short passage giving clue of sequence
of different items eg. lathe , compressor...
Six problems are based upon their positions
(reasoning)
15.One reading comprehension was given of which
atleast 7 to 8 questions were asked.
===SENTHIL (EEE-NITC)
hi friends,
--
telco 2002
two sections
aptitude
technical
technical is different for mechanical,matelargical and
same for
electrical and electronics
technical is very easy and contains only elementary
concepts
in aptitude there were 40 questions in 30 minutes
there were different sets with question no. changed
last 10 questions were on material science
like what is the role of sulphur in rubber
what is mixed in steel like that
curie temperature of .............
ans of one ques was doping
photodiode is made of si,ge,gallium aresnide none
newton's law of viscosity
luemn is unit of what
motor used in traction
remaining 30 questions are
*there are cars two red which are adjecent to each
other
four yellow
two green which are not adjecent
three blue which are adjecent
red and green are on the ends
now there were six questions
like if green is on 8th position then which is on 6th
or which cannot
be
there was one reading comprehension
and five questions
first question was on main theme
one of the question was if u have to devide this
passage in two parts
then what would be the first line of second passage
this passage was on (reading and writing skills)
so first part was on writing and next part was on
reading
remaining 19 questions were on mathematical apti
like an equation was given 2x3+kx2+7x+8
for what value of k (x+2)is a facotor of given
equation
answer of one question was 444(two trains are coming
towards each
other and one covers 60km more than the other tell the
total distance
covered )
some questions were engineering question type
like a car is running at some speed and break of some
retardation
was applied then what distance it will cover before
stopping
v2=u2+2as
basically the paper was easy and u can easy make it
in our(electrical) technical paper lots of electronics
questions were
there
then there was gd which is an elimination round
topics were
an organization needs leader not managers
if something is broken let it remains so
your dress is index of ur character
will globalization kill indian industry
disinvestment is good or bad
indian youths are more inclined towards monitoring
comforts rather
than challenging jobs
prepare and do well in gd and try to speak as much as
possibe and try
to put good points
they are looking for people who are good leader
try to lead the group
then interview is
core and little bit of hr
technical paper of electrical and electronics
1.(s+a)(s+b)/(s+c)(s+d)
at what phase diff. freq tends to infinity
2. least power is consumed in
ttl,cmos etc
3.which of the following represents an integrater
there were four fig. having opamp and arrangement of
capacitors and
resistors
4.the resolution of adc depends on
add line,data line,clock,none of these
5.the speed of microprocessor depends on
add line data line clock none
6.the motor is started in star and run at delta to
ans reduce rush in current
7.best speed regulation in dc motor
series shunt universal none
8.ques on emitter follower
calculation and its input resistance
9.its output resistance
10.ques on feedback amplitude
11.input impedence of opamp is
high low
12.16 bit add line may address how many locations
13.two ques on simple resistance calculations
14.a ckt is given containing a battery resistance and
inductor
find steady state current
15.ques on ttl cmos rtl and dtl comparison
16.which is used for power factor improvement
and synchronus motor
17.induction motor running on no load has
and low power factor
18.speed of induction motor can be controlled by
voltage,freq,both,none
19.igbt is
ans power amplifier
20.one ques on bridge rectifier
21.the logic value 1 of ttl is
some voltage (1.7,.8 etc)
__________________________________________________
hi friends,
this mail is the continuation of the previous
mail OF TELCO.
aptitude section
be fast as questions really need time
#2 questions from series completion----- answer of
one of which is 60
one completion of series of alphabets answer was
bab
#1 question was that if x* is greatest integer less
then that number then to find the value of the
sequence answer was 6
#1 question in which relation between x an y are
given in form of series of numbers, guess the relation
between x and y and complete the series
#1 question in which two linear equation was given, in
terms of variables x,m,z,y then to find the coorect
choice--- choices comprise of other relation between
the parameters
#1 question in which a ratio of a mixture composition
made of cement and some other materials was
given....to find the amount of cement
needed.......answer was 45
#2 or 3 simple question based on percentage and profit
and loss
#1 question based on BODMAS rule...... answer was
.0012
#1 question in which a square was inscribed in a
circle to find the area of square answer was
2a^2
#1 question in which it was given that x<y then which
will be greater than x but less than y answer was
( x+y)/2
#1 question in which relation between g[x] and f[x]
was given then to find the relation between them is to
be found---------- confirm there is a correction in
this question so ask from them
#1 simple question based on time and distance
#2 question based on coding-decoding the trick of
first question was the two alphabets before the
alphabet of first word was the last alphabet of second
word the trick of second wasthe position of
alphabet in terms of no. (like A=1)from beginning and
from the end varies alternately
PASSAGE
a long passage was there based on principle of
induction that a shopkeeper offerd an apple to the
writer.....it was green and sour then he offers
another one which was also green and sour then when
the writer was offered the third one which was also
green he deducted that it is also sour so was then
discussed the nature of humanbeing to accept the
inference from induction.
then there was 5 to 6 question based on the passage
answer of 1 question was writer is from...... india
another one......... writer is a scientist
another one........apple has been used as ....... an
object of passage
question that what does "natural law" means........
answer is most probably...... induction
question that what does "extensive reference" means
question in which two statements was given and a
conclusion made on basis of them was given........it
represents syllogism
# quex. based on jigs and fixtures
# quex. based on carbon content in die steel
# return mechanism is not used in ....a . bore b.
planar ...
#what does 123+ .5 represents...
#angles r in the ratio 1:2:2... then the triangle
is.... isosceles
# distance between a &c is 60, a&b is 50 and b&c is
50.... find the shortest distance from pt. b on line
ac..... ans. 40 km.
ARRANGING QUESTIONS...
a question of arranging a series of mechanical
instruments on the side of a wall ...they were seven
in number........name of mechanical instruments was
given just to confuse you...... take the instruments
as lathe(l), polisher(p), air conditioner(a), H, B, D,
S
conditions... # lathe must always be at position 2
a&h must be together, s can stay with either b or
d.., lathe and polisher must not be adjacent...
# deduction... p can either be at 5 or 7(two questions
on this)
5 more questions on the above conditions
....... it is a simple question of arranging it.......
there were 5 to 6 question based on it
-----------------------------------------------------------------------
SOME MORE APTI QUESTIONS(SOME OF THEM MIGHT BE SAME)
APTITUDE:
1.0.0024/.012*.006=
2.A square is inscribed in a circle , radius of the
circle is 'a'.Area of the square=
Ans:2a^2
3.The angle of a triangle is 1:2:2 then the triangle
is
Ans:isosceles
4.X's salary is 150% of Y, and Z's salary is 75% of Y,
their total salary is
Ans:1000
5.g[x]=1+x/2, then value of g[2x] in terms of g[x] is
6.If X<Y ,which of the following is greater than X and
less than Y
Ans:sqrt(X*Y)
7. For the sequence 4,8,6,18,15,.....,the next number
is
8.to find the relationship between X & Y for the given
value
ans:4X+2=Y
9.(X*) is the largest integer but less than X.find the
value of (5.2*) + (4*)-(2*)=?
Ans:6
10. Series of An is given by (An-1)^3,if first value
of An is 1 find the series up to four steps
Ans:0,-1,-8,-729
11.Simple questions based time and distance
12.In a city 90% people has car, 15% has motorcycle,
100% has car or motorcycle then how many of them have
only car and motorcycle.
13.Two problems are based upon coding
14.There was a short passage giving clue of sequence
of different items eg. lathe , compressor...
Six problems are based upon their positions
(reasoning)
15.One reading comprehension was given of which
atleast 7 to 8 questions were asked.
Best of luck
The order of the questions is not the same as in the question paper.There
were two sections apti &technical. Both had 40 questions nad the time for each section
was 30 minutes. I am sending as many questions as I could recall.
APTITUDE:
1. a long expression 164m2n2+…………+300n+225.what is the square root of this
expression.
Ans. (a)
2.In a town there are 3 clubs A,B and C having 40,50 and 60 members. 10 people are
members of all clubs.70 people are members of only one club.and all people are members
of at least one club.find how many people are members of exactly two clubs.
3.Two persons are walking towards each otherand then back to there original places.. One
is at A and and the other is at B. they meet first time at a distance of 12 km from B and
while returning they meet at a distance of 6 km from A.find the distance AB. .
ans. 30.
4. value of 6 + ( 6 + ( 6 + ........ .
Ans. 3.
6. pick the odd one out: (a)bull (b)mule(c) bear (d) stag.
Ans. Mule.
8. find thw word which has the meaning : without fear of punishment.
Ans. Impunity.
9. Astranaut:cosmonaut::?: ?
find thw pair which has opposite meaning to the given pair.
Ans. (c)aviator:navigator.
10.n is the no. of copies in each book. b is the no. of books. nb<200. if n is decreased by
b increases by 3. what is the value of nb?
11.there was a problem on clock. The clock shows 12:30p.m. on march 1. it stops for I
min after each hour. What is the actual time whan the clock shows 12:30 p.m.on march 3.
12. There are 3 letters and 3 envelopes. In how many ways one can send 1 letter wrong.
Ans. None of these. ( DO NOT WASTE TIME ON SOLVING THIS QUESTION.)
4-5 questions were on assertion reasoning. One question is given. Two sentences are
given. Then 4 choices. A if only one statement is needed to answer the question.etc.
the following 3 questions are of assertion reasoning type.
16.There are four consecutive even integers. Their average is 12. can u find the no.s
then two statements which I have forgotten.
Ans.(a)
17.There was a reading comprehension. One question was to give a suitable title for the
passage.
There were 3 other questions from the same passage.
21..Data interpretation. there was a bar chart given for the production and consumption of
oil of 6 or 7 countries. There were 6 questions based on the chart.i don’t remember the
questions exactly. But I remember the ans of some which I am giving.
Ans of first question was 3/2.
Ans of 2nd ques was 40.
Ans of 4th was finland.
27. unit of luminous intensity.
Ans candela.
ans. (1/100)+(1/99)+(1/101).
28. A and B together do a work in 10 days. A is paid thrice than B. Equal wage is given
for equal work. Then in how many days B can do the work alone?
Ans. 40 days.
29. Subhas works 2 hrs. and Kiran works 5 hrs then half the work is completed. Then
they work together for 3 hrs. then 1/20 of the work remains to be done. Then how much
time will they take to complete the work alone?
Ans. Subhas – 6hrs. KIran - 15 hrs.
Then there were 6 questions on analytical reasoning. There is an island named kya kya.
There only two kinds of people live one who ( aisa hi kuch tha bahut hi bakwas tha. Kuch
samajh nahin aaya tah.) for this the BRM (ims) may be helpful.
6. What is the part in CNC machine which gives the exact position of the x and y
coordinates.?
Ans. Interpolater.
7. in an anthromorphic robot there are three motions of the wrist roll, yaw and pitch.
Determine which one is along x axis, which along y axis and which along z axis.
There was a diagram of the cutting tool showing the shear angle and the rake angle.
8. what is the angle α? Ans. Rake angle. (THE ANGLE IS GIVEN AS α AND NOT γ. SO
DO NOT CONFUSE IT WITH THE CLEARANCE ANGLE.)
9. what is the formula of the chip reduction coefficient?
Ans. Cos(β-α)/sinβ.
10. the order of cope , drag and cheek in the process of moulding.
(a) drag,cope,cheek (b) cope, cheek, drag. Etc. ans. Don’t know.
12.In power plant, nuclear plant and space ship what is the method used for maintanence?
(a) breakdown maintenance (b) preventive maintenance.
Ans is most probably (a).
13. Internal gear cannot formed by?(a) shaping (b)broaching (c) milling
Ans. Shaping.
14. Feed is not associated with any type of motion in which process?
Ans. Broaching.
15. The no. of teeth in a milling cutter is 8. the feed per teeth is 0.1 mm. The cutter speed
is 150 rpm. What is the table speed?
Ans. 8*0.1*150=120mm/min.
16. If aspect ratio of something is more than 50 i.e. length>50*diameter, then by which
method will u make the object?
(a) drill with 1 mm diameter.
(b) laser machining.
(c) ultrasonic machining.
Ans. (b)
18.The pitch of a screw in an interpolator is 2 mm. the thread is double start. And there
are 200 holes. Find the BLU.
Ans. (2*2)/200 = 20 micrometers.
19. Then a question on double acting compressor.
There were some questions on assertion reasoning. Two statements are given .
Then mark (a) if A and R are both correct and R is the correct explanation for it.
I remember only two questions from there.
20. This question was regarding the insulation on a cylinder. Whether it has some critical
radius for minimum heat transfer.
21. A bob is hung with a thread from the ceiling. Another bob moving at speed in x
direction hits it. Then R . the momentum of both bobs is conserved in x direction.
A. Kinetic energy of both bobs is conserved.
22. At the point of contact in the meshing of two gears what is same?
(a) angular velocity (b) linear speed etc.
Ans. (b).