Anda di halaman 1dari 7

INSTALLATION INSTRUCTIONS SOL S64 FOR SEIKO COLORPAINTER PRINTERS

1. BEFORE FILLINK INK CARTRIDGES INSTALLATION: Ensure the latest firmware is installed Empty the waste bottle

Load the substrate Put the printer offline (by pressing the online button) Go to `service mode by pressing: Cancel, shift, cancel, cancel Enter the password: Shift, arrow up, arrow down, arrow right

Go in the menu to `H. adjustment with the arrow left button. Press enter

Fillink Technologies S.A. 5 Excelsiorlaan - 1930 Zaventem - Belgium (t) +32-2-7168580 - (f) +32-2-7168599 - (e) info@fillink.net www.fillink.eu.com

INSTALLATION INSTRUCTIONS SOL S64 FOR SEIKO COLORPAINTER PRINTERS

You will have H. adj pattern > Nozzle. Press enter to make the nozzle test Put the printer offline (by pressing the online button) Put the printer online (by pressing the online button) Go to `service mode by pressing: Cancel, shift, cancel, cancel Enter the password: Shift, arrow up, arrow down, arrow right Go in the menu to`H. maintenance with the arrow down button. Press enter Choose Ink extract all. You are now requested to remove the ink cartridges Remove all ink cartridges 2. FILLINK INK CARTRIDGES INSTALLATION: After removing the ink cartridges, the printer will request you to install the dummy cartridges Insert the 6 dummy cartridges in the printer Press enter when asked to extract the ink

Fillink Technologies S.A. 5 Excelsiorlaan - 1930 Zaventem - Belgium (t) +32-2-7168580 - (f) +32-2-7168599 - (e) info@fillink.net www.fillink.eu.com

INSTALLATION INSTRUCTIONS SOL S64 FOR SEIKO COLORPAINTER PRINTERS

The ink will be extracted from the secondary ink tanks to the waste bottle. This operation will take around 12 minutes When the ink extract is done, turn the printer off

Remove the dummy cartridges Insert FILLINK ink cartridges

Turn on the printer Put the printer off line (by pressing online button) Go to `service mode by pressing: Cancel, shift, cancel, cancel Enter the password: Shift, arrow up, arrow down, arrow right Go in the menu to `H. maintenance with the arrow down button Press enter when asked to charge the ink (ink charge all). This operation will take around 12 minutes

Fillink Technologies S.A. 5 Excelsiorlaan - 1930 Zaventem - Belgium (t) +32-2-7168580 - (f) +32-2-7168599 - (e) info@fillink.net www.fillink.eu.com

INSTALLATION INSTRUCTIONS SOL S64 FOR SEIKO COLORPAINTER PRINTERS

When the ink charge is done, put the printer online (by pressing online button) Put the printer off line (by pressing online button) Go to `service mode by pressing: Cancel, shift, cancel, cancel Enter the password: Shift, arrow up, arrow down, arrow right Go in the menu to`H. adjustment with the arrow left button. Press enter Select cleaning, strong. Press enter (the printer will start a strong cleaning)

Put the printer online (by pressing the online button) Put the printer offline (by pressing the online button) Go to `service mode by pressing: Cancel, shift, cancel, cancel Enter the password: Shift, arrow up, arrow down, arrow right Go in the menu to`H. adjustment with the arrow left button. Press enter Select`H. adj pattern > Nozzle. Press enter to make the nozzle test

Fillink Technologies S.A. 5 Excelsiorlaan - 1930 Zaventem - Belgium (t) +32-2-7168580 - (f) +32-2-7168599 - (e) info@fillink.net www.fillink.eu.com

INSTALLATION INSTRUCTIONS SOL S64 FOR SEIKO COLORPAINTER PRINTERS

Put the printer online (by pressing the online button) The printer is ready to print with Fillink ink

Install Fillink ICC profiles by downloading them from: http://www.fillink.eu.com/icc_profiles/icc_products.htm

3. ENVIRONMENTAL RECOMMENDATIONS Every morning, when starting the printer, do capping and wipe cleaning Before starting to print make sure that the room temperature is at least 18 (Celsius) After automatic cleaning, it is recommend to clean the heads with the swab Printing temperature under the head should be not higher than 40 Printing stripe bar is necessary to prevent ink from drying on the heads Make sure that the substrate is free from dust, fiber, etc Before turning the printer off, clean the print-heads with a swab

Fillink Technologies S.A. 5 Excelsiorlaan - 1930 Zaventem - Belgium (t) +32-2-7168580 - (f) +32-2-7168599 - (e) info@fillink.net www.fillink.eu.com

INSTALLATION INSTRUCTIONS SOL S64 FOR SEIKO COLORPAINTER PRINTERS

4. RECOMMENDATIONS FOR USING THE CARTRIDGES The cartridge MUST be replaced with a new one when the ink level has reached 3%, no less Ensure that the temperature of the cartridges reaches room temperature before inserting them in the printer Shake the cartridges well before installing them into the printer

5. TROUBLE SHOOTING:

5.1 Problem: Loosing nozzles before start to print Solution:


Do an automatic cleaning from the menu Clean the heads with the swab Check the room temperature Remove the covers on both sides of the machine and check if there are air bubbles inside the pipes If air bubbles are visible, check if the cartridge is empty and remove the air from the pipes using`cleaningfrom the menu

5.2 Problem: Loosing nozzles while printing (starvation) Solution:


Check the substrate to see if it is dusty Check both print temperature as well as room temperature Check the ink level in the cartridge Ensure that latest firmware is installed

5.3 Problem: Overspray Solution:


Change the head voltage: Put the printer offline (by pressing the online button) Open the heads cover The actual recommended voltage of the head is written on the head itself ( one voltage for the right and another one for the left)

Fillink Technologies S.A. 5 Excelsiorlaan - 1930 Zaventem - Belgium (t) +32-2-7168580 - (f) +32-2-7168599 - (e) info@fillink.net www.fillink.eu.com

INSTALLATION INSTRUCTIONS SOL S64 FOR SEIKO COLORPAINTER PRINTERS

Please check them and be sure it is the same voltage that is indicated on the printers screen (last step) Go to `service mode by pressing: Cancel, shift, cancel, cancel Enter the password: Shift, arrow up, arrow down, arrow right Go in the menu to `H. adjustment.Press enter Choose`drive voltagewith the arrow down button Select the required head and adjust the voltage ( Maximum +/- 1VOH) until the printed results are improved

FILLINK HOTLINE is reachable by phone on +32.495.228.883 or by Email at support@fillink.net

Fillink Technologies S.A. 5 Excelsiorlaan - 1930 Zaventem - Belgium (t) +32-2-7168580 - (f) +32-2-7168599 - (e) info@fillink.net www.fillink.eu.com

Anda mungkin juga menyukai