(SCG-60)
User Manual
Contents
1.INTRODUCTION ................................................................... 1 2.SYSTEM CONFIGURATION DIAGRAM ............................ 2 3.MECHANISM DIAGRAM..................................................... 2 4. DEVICE LIST & INSTALLATION ....................................... 4 5. WEB PAGE SETTING........................................................... 6 5.1 System Parameter Setting ............................................... 6 5.1.1 PC Time ................................................................. 6 5.1.2 System Setup ......................................................... 6 5.1.3 Card Setup ............................................................. 7 5.2 E1 PRI Setting ................................................................ 8 5.4 Network Setting .............................................................. 9 5.5 Account Setting............................................................. 10 5.6 CDR .............................................................................. 10 5.7 Online Monitoring ........................................................ 11 5.8 Log PRI Data ................................................................ 11
1.Introduction
GSM E1 Channel Bank(SCG-60) is the newest product after our Digital Mobile Trunk(DMT). Each SCG-60 system consists 2 sets of Channel Bank. Channel Bank connects to E1 PRI of Exchange or VoIP Trunk Gateway. The 30 PRI channels are individually connected to 30 ports of GSM channel, and is a perfect transform device between digital circuits to GSM channels. SCG-60 can provide Call Detail Record (CDR) for traffic and billing management. SCG-60 system can be configured and queried through web page by remote console, which includes the network IP setting, password validation, call detail record, and monitoring the channel status, etc.
-1-
SCG-60 consists 2 sets of Channel Bank. One set of Channel Bank connects to one ISDN E1 PRI. When an incoming call received from the E1 channel, the MCU will retrieve the called number and dial out the number from the corresponding GSM channel. These two channels are connected so that this call has been conducted into the GSM channel. The incoming call from the GSM channel will be treated in the same way.
3.Mechanism diagram
-2-
SCG-60 dimensions: 19" standard cabinet, Height 4U, Depth 42CM. It consists 2 sets of channel bank, one set of channel bank consists 5 x GSM6 and 1 x Trunk MCU. GSM : provides 6 GSM ports per card. There are 6 LEDs on the front plate, indicating the status of each port. [ SCG-60 spec in the GSM6 ] Providing 6 channels GSM per card. LED GSM status display. GSM/GPRSPhase 2+ Compliance GSM Frequency bands: Tri Band EGSM 900, DCS 1800 and PCS 1900MHZ Power Consumption Speech Mode230mA(min)260mA(max) Standby Mode<6mA(paging rate 2) <3mA(paging rate 9) at GSM 900MHz SIM card holder : External attached - connected in the back panel Antenna : 50 Ohm antenna coaxial connector Temperature range :Normal operation: -20 to +55 Restricted operation: -25 to -20 and +55 to 70 Storage:-40 to +85 [ E1 Trunk (ISDN E1 PRI) specification ]
No. 1 2 3 4 5 6 7 8 9 10 Items ISDN PRI Line Length Location Cause Value Signaling Number plan Codec User Side Network Side Signaling Scenario 30B+1D G.703 Q.850 Standard Q.931 Standard Unnumbered G.711 a law SW type = Euro ISDN Net5 SW type = Euro ISDN Net5 (1)While called to hang up, send out Disconnect signal. (2)Setup time Max. = 20sec 5ESS Default Value DS0=64K/Sec (120) Adjustable Memo
Antenna
5X4 times
-3-
[ Power Card ] Input Voltage: AC90-135V, AC180-264V, 50Hz~60Hz. Input Current: 8A for 115VAC, 5A for 230VAC. Type: Switching. Output:+3.3V_28A,+5V_30A,+12V_15A,-5V_0.5A,-12V_1A,+5VSB_2A. Total Power: 300W. Power Panel.
4.2. Installation
(1) Check if all the parts are included. (2) Inside the GSM6 card, there are 6 GSM SIM card holders. Put SIM cards in the corresponding position.
-4-
3 6
2 5
1 6 4 3
(3) Lock up all the antennas in the front of the GSM6 card. (There are 30 antennas in the antenna box for 5 pieces of GSM6 card)
Total 30 antennas (4) Connect the E1/PRI cable for the Trunk/MCU card. (5) Connect the network cable for the Trunk/MCU card. The default IP address is 192.168.0.107. You can change the IP address afterwards.
-5-
LAN E1
5.1.2 System Setup (1) PRI ModeSetup the PRI mode for User(TE)/Network(NT) mode
-6-
(2) Hide the Caller ID : Hide or show the caller ID when dial out from the GSM module
(3) Option for line is not ready : setup the behavior when the corresponding outgoing channel is not ready. The option can be 1) Automatically hang up the call by the system, or 2) Wait till the incoming call hangs up.
-7-
-8-
5.3 GSM Channel Setting GSM Outbound : GSM Setup : Setup the mobile number for each GSM channel
-9-
5.6 CDR
View the call detail record
-10-
GSM System : Show the network usage of the GSM channel Total 30 channels Signal : Signal strength Status : Indicates whether this call is from trunk to GSM, or from GSM to trunk Trunk Status : Show the line status, e.g. Ring, HangUp
-11-