1
I B.Tech Regular Examinations, May/Jun 2008
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
3. (a) State and explain one dimensional and three dimensional flow.
(b) Explain the characteristics curves of centrifugal pump. [8+8]
4. Write notes on multiple effect evaporation and methods of feeding with suitable
diagram. [16]
7. (a) Write about the selection of dispersion phase for liquid-liquid extraction.
(b) Describe rotating disk and centrifugal extractors. [8+8]
⋆⋆⋆⋆⋆
1 of 1
Code No: 07A10801 Set No. 2
I B.Tech Regular Examinations, May/Jun 2008
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
3. (a) Define fluid and classify the fluids with suitable examples.
(b) Differentiate between single and multi stage pumps.
(c) What is pump? Explain briefly reciprocating pumps. [8+4+4]
5. (a) What are absorption and desorption processes? Explain with suitable exam-
ples.
(b) Absorption and Desorption processes may be handle in two ways what are
they? Explain.
(c) Describe the essential features and operation of packed absorption column and
mention the three main steps in its design. [4+4+8]
6. Compare the packed towers with tray towers and also discuss merits & demerits.
[16]
7. (a) Draw a neat sketch of a triangular diagram and explain how the binodal curve
and tie- line can be represented for the system.
(b) What are the differences between a countercurrent and a crosscurrent cascade?
(c) In a ternary extraction system, what are the solute, solvent, and carrier?
[6+6+4]
8. (a) Explain divided fixed bed reactor with inter cooling between catalyst beds.
(b) Differentiate between fluidized and semi fluidized beds. [10+6]
⋆⋆⋆⋆⋆
1 of 1
Code No: 07A10801 Set No. 3
I B.Tech Regular Examinations, May/Jun 2008
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. Discuss briefly:
(a) Flotation
(b) Filtration. [2×8=16]
2. Define material balance and enumerate the different steps to follow in material
balance calculations. [16]
5. (a) Obtain the expressions for height of absorption column in terms of overall gas
phase mass transfer coefficient.
(b) What is necessary condition for absorption to take place? Define active com-
ponent.
(c) Define Fick’s law of diffusion. [8+4+4]
1 of 2
Code No: 07A10801 Set No. 3
8. (a) Explain in detail about adsorption.
(b) Differentiate between reactivation and regeneration.
(c) Write short notes on Vander Waals adsorption. [8+4+4]
⋆⋆⋆⋆⋆
2 of 2
Code No: 07A10801 Set No. 4
I B.Tech Regular Examinations, May/Jun 2008
INTRODUCTION TO CHEMICAL ENGINEERING
(Chemical Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. Discuss briefly:
(a) Flotation
(b) Screening. [2×8=16]
2. (a) Energy associated with mass be classified in a number of ways. What are
these?
(b) What are the different ways by which energy that is not associated with in
the mass classified?
(c) Define standard heat of reaction and discuss about heat of reaction at constant
pressure and constant volume. [5+2+9]
3. (a) With the help of a neat figure discuss about the development of a boundary
layer on a flat plate.
(b) Write the expression for thickness of boundary layer if the boundary layer is
laminar and turbulent, respectively. [12+4]
5. (a) Mass transfer may occurs in different ways, name any five.
(b) What are phenomena that must exists in a mass transfer opeartion.
(c) There are many similarities and differences between various mass transfer
operations mention them. [5+3+8]
1 of 2
Code No: 07A10801 Set No. 4
8. (a) Explain tray drier with neat sketch.
(b) Differentiate between wet bulb and dry bulb temperature. [10+6]
⋆⋆⋆⋆⋆
2 of 2