____________________________Features
o On-Resistance, <400 max o Transition Time, <500ns o On-Resistance Match, <10 o NO-Off Leakage Current, <20pA at +25C o 1.5pC Charge Injection o Single-Supply Operation (+4.5V to +30V) Bipolar-Supply Operation (4.5V to 20V) o Plug-In Upgrade for Industry-Standard DG508A/DG509A o Rail-to-Rail Signal Handling o TTL/CMOS-Logic Compatible o ESD Protection >2000V, per Method 3015.7
MAX338/MAX339
______________Ordering Information
PART MAX338CPE MAX338CSE MAX338C/D MAX338EGE MAX338EPE MAX338ESE MAX338EJE MAX338MJE TEMP. RANGE 0C to +70C 0C to +70C 0C to +70C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -55C to +125C PIN-PACKAGE 16 Plastic DIP 16 Narrow SO Dice* 16 QFN 16 Plastic DIP 16 Narrow SO 16 CERDIP 16 CERDIP**
________________________Applications
Data-Acquisition Systems Test Equipment Military Radios PBX, PABX Sample-and-Hold Circuits Heads-Up Displays Communications Systems
Ordering Information continued at end of data sheet. * Contact factory for dice specifications. ** Contact factory for availability.
TOP VIEW
A0 1 EN 2 V- 3 NO1 4 NO2 5 NO3 6 NO4 7 COM 8 16 A1 15 A2 14 GND
NO1 NO2 NO3 NO4 NO5 NO6 NO7 NO8 CMOS DECODE LOGIC COM
MAX338
DIP/SO
Continued at end of data sheet.
A2
A1
A0
EN
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxims website at www.maxim-ic.com.
Note 1:
Signals on NO, COM, EN, A0, A1, or A2 exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum current ratings.
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
INO(OFF)
ICOM(ON)
_______________________________________________________________________________________
MAX338/MAX339
Negative Supply Current DYNAMIC Transistion Time Break-Before-Make Interval Enable Turn-On Time Enable Turn-Off Time Charge Injection (Note 3) Off Isolation (Note 6)
I-
V A A A
10
ns ns ns ns
1.5
pC
VISO
TA = +25C
-75
dB
-92
dB
2 3 11
pF pF
COM-Off Capacitance
COM-On Capacitance
f = 1MHz, VEN = 0.8V, CCOM(OFF) VCOM = 0V, Figure 8 f = 1MHz, VEN = 2.4V, CCOM(ON) VCOM = 0V, Figure 8
pF
_______________________________________________________________________________________
tON(EN)
TA = +25C
280
500
ns
tOFF(EN)
TA = +25C
110
500
ns
TA = +25C
1.8
pC
Note 2: The algebraic convention where the most negative value is a minimum and the most positive value a maximum is used in this data sheet. Note 3: Guaranteed by design. Note 4: RON = RON(MAX) - RON(MIN). Note 5: Leakage parameters are 100% tested at the maximum rated hot temperature and guaranteed by correlation at +25C. Note 6: Worst-case isolation is on channel 4 because of its proximity to the drain pin. Off isolation = 20log VCOM/VNO, where VCOM = output and VNO = input to off switch.
_______________________________________________________________________________________
MAX338/MAX339
400
10V 15V
+12V
+15V
+20V
-15 -10
-5
10
15
20
10 VCOM (V)
15
20
VCOM (V)
700 600 500 RON () 400 300 200 100 0 0 5 VCOM (V) 10 V+ = +15V V- = 0V +125C +85C +25C -55C
1000 100 OFF LEAKAGE (nA) 10 1 0.1 0.01 0.001 0.0001 INO (OFF) ICOM (OFF) V+ = +15V V- = -15V
1000 100 ON LEAKAGE (nA) 10 1 0.1 0.01 0.001 0.0001 ICOM (ON)
15
25 45
65
85 105 125
25 45
65
85 105 125
TEMPERATURE (C)
TEMPERATURE (C)
40 30 20 Qj (pC) 10 0 -10 -20 -30 -15 -10 -5 0 VCOM (V) 5 10 CL = 100pF V- = 0V 15V +5V +12V
1000 I+, VA(ALL) = 2.4V 100 10 I+, I- (A) 1 0.1 I0.01 0.001 I+, VA = 0V
1000
200 100 0
15
25 45
65
85 105 125
TEMPERATURE (C)
5 OR 5V
(SINGLE)
10 OR 10V
(SINGLE)
15
20
_______________________________________________________________________________________
__________Applications Information
Operation with Supply Voltages Other than 15V
Using supply voltages less than 15V will reduce the analog signal range. The MAX338/MAX339 switches operate with 4.5V to 20V bipolar supplies or with a +4.5V to +30V single supply. Connect V- to GND when operating with a single supply. Both device types can also operate with unbalanced supplies such as +24V and -5V. The Typical Operating Characteristics graphs show typical on-resistance with 20V, 15V, 10V, and 5V supplies. (Switching times increase by a factor of two or more for operation at 5V.)
V+
NO
COM
Vg
Overvoltage Protection
Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maximum ratings, because stresses beyond the listed ratings may cause permanent damage to the devices. Always sequence V+ on first, then V-, followed by the logic inputs NO and COM. If power-supply sequencing is not possible, add two small signal diodes in series with supply pins for overvoltage protection (Figure 1). Adding diodes reduces the analog signal range to 1V below V+ and 1V above V-, but does not affect the devices low switch resistance and low leakage characteristics. Device operation is unchanged, and the difference between V+ and V- should not exceed 44V.
6
V-
_______________________________________________________________________________________
MAX338/MAX339
MAX338
EN GND 50 +15V V+ A1 A0 -15V V-
NO8 COM
+10V VOUT 10pF 1k LOGIC INPUT +3V 50% 0V VNO1 SWITCH OUTPUT VOUT
90%
NO1B NO1A-NO4A
10V
0V 90% VNO8
MAX339
EN GND 50
tTRANS
ON
tTRANS ON
-15V
EN
MAX338
tr < 20ns tf < 20ns
A0 A1 50
MAX339
GND COMB V1k -15V VOUT 35pF
+15V V+ NO1-NO8 A0 A1 A2 GND 50 -15V V1k LOGIC INPUT +3V 50% 0V VOUT 80% COM VOUT 10pF 0V SWITCH OUTPUT tOPEN
+2.4V
EN
+5V
MAX338
+15V RS NO EN VS CHANNEL SELECT A0 A1 A2 COM V+ LOGIC INPUT VOUT VOUT VOUT VOUT IS THE MEASURED VOLTAGE DUE TO CHARGE TRANSFER ERROR Q WHEN THE CHANNEL TURNS OFF. -15V Q = CL x VOUT +3V OFF 0V ON OFF
MAX338
CL = 100pF GND V-
_______________________________________________________________________________________
MAX338/MAX339
VIN
V+
MAX338
COM
MAX338
EN
V-
10nF
10nF
-15V
CROSSTALK = 20log
VOUT VIN
Figure 7. Crosstalk
MAX338
NO8
-15V
_______________________________________________________________________________________
16 A1 15 GND 14 V+
NO1A NO2A NO3A NO4A NO1B NO2B COMB NO3B NO4B CMOS DECODE LOGIC COMA
MAX339
DIP/SO
A1
A0
EN
A2 X 0 0 0 0 1 1 1 1
A1 X 0 0 1 1 0 0 1 1
A0 X 0 1 0 1 0 1 0 1
EN 0 1 1 1 1 1 1 1 1
ON SWITCH None 1 2 3 4 5 6 7 8
A1 X 0 0 1 1
A0 X 0 1 0 1
EN 0 1 1 1 1 MAX339
ON SWITCH None 1 2 3 4
10
______________________________________________________________________________________
MAX338/MAX339
A1 14 LOGIC
A2
EN 16
A0
A1 14 LOGIC
GND
15
13
15
13
1 2 3 4
12 11 10 9
1 2 3 4
12 11 10 9
5 NO4
6
COM
7 NO8
8
NO7
5 NO4A
6
COMA
7 COMB
8
NO4B
MAX338
MAX339
______________________________________________________________________________________
11
EN
A0
A1
A2
GND
EN
A0
A1
V+ VNO1 NO2 NO3 NO5 NO6 N.C. 0.114" (2.89mm) N07 VNO1A NO2A NO3A
V+
NO4
NO4A
12
______________________________________________________________________________________
MAX338/MAX339
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 2001 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.