Input attenuator
It is important to know the fundamental tradeoffs that are involved in RBW selection, for cases where the user knows which measurement parameter is most important to optimize. But in cases where measurement parameter tradeoffs cannot be avoided, the modern spectrum analyzer provides ways to soften or even remove the tradeoffs. By utilizing digital signal processing the spectrum analyzer provides for a more accurate measurement, while at the same time allowing faster measurements even when using narrow RBW.
Spectrum analyzer
DUT
Signal delivery network Cables Adapters Noise Shift reference plane Figure 6. Test setup
Increasing the input attenuator setting reduces the level of the signal at the input mixer. Because the spectrum analyzers noise is generated after the input attenuator, the attenuator setting affects the signal-to-noise ratio (SNR). If gain is coupled to the input attenuator to compensate for any attenuation changes, real signals remain stationary on the display. However, displayed noise level changes with IF gain, reflecting the change in SNR that result from any change in input attenuator setting. Therefore, to lower the DANL, input attenuation must be minimized.
Figure 10. Signal after minimizing resolution bandwidth, input attenuator and using logarithmic power averaging
fundamental at the mixer, the SHD increases 2 dB. However, since distortion is determined by the difference between fundamental and distortion product, the change is only 1 dB. Similarly, the third-order distortion is drawn with a slope of 2. For every 1 dB change in mixer level, 3rd order products change 3 dB, or 2 dB in a relative sense. The maximum 2nd and 3rd order dynamic range can be achieved by setting the mixer at the level where the 2nd and 3rd order distortions are equal to the noise floor, and these mixer levels are identified in the graph.
SHI
10
20
30
40
50
No ise (1 0k Hz BW )
(dBc)
60
70 Maximum 2nd order dynamic range 80 Maximum 3rd order dynamic range Optimum mixer levels
90
100 60
50
40
10
3rd ord er 2n do rd er
+10
(dBc)
To increase dynamic range, a narrower resolution bandwidth must be used. The dynamic range increases when the RBW setting is decreased from 10 kHz to 1 kHz as showed in Figure 13. Note that the increase is 5 dB for 2nd order and 6+ dB for 3rd order distortion. Lastly, dynamic range for intermodulation distortion can be affected by the phase noise of the spectrum analyzer because the frequency spacing between the various spectral components (test tones and distortion products) is equal to the spacing between the test tones. For example, test tones separated by 10 kHz, using a 1 kHz resolution bandwidth sets the noise curve as shown. If the phase noise at a 10 kHz offset is only -80 dBc, then 80 dB becomes the ultimate limit of dynamic range for this measurement, instead of a maximum 88 dB dynamic range as shown in Figure 14.
er
o rd
40
50
No
ise
(1
0k
60 Noi se ( 70
Hz
BW
1k
Hz
BW
2nd order dynamic range improvement 80 3rd order dynamic range improvement 90
60
50
40
10
3rd
2n
do
rd
30
er
+10
60 (dBc) 70
80
90
100
110 60
50
40
10
+10
Figure 14. Phase noise can limit third order intermodulation tests
If the responses in Trace A and Trace B differ, as in Figure 15, then the analyzers mixer is generating internal distortion products due to the high level of the input signal. In this case, more attenuation is required.
In Figure 16, since there is no change in the signal level, the internally generated distortion has no effect on the measurement. The distortion that is displayed is present on the input signal.
Figure 18. Comparing the sweep time for FFT and swept mode
Bucket number
Positive peak, negative peak and sample detectors are shown in Figure 20. Peak detection mode detects the highest level in each bucket, and is a good choice for analyzing sinusoids, but tends to over-respond to noise. It is the fastest detection mode. Sample detection mode displays the center point in each bucket, regardless of power. Sample detection is good for noise measurements, and accurately indicates the true randomness of noise. Sample detection, however, is inaccurate for measuring continuous wave (CW) signals with narrow resolution bandwidths, and may miss signals that do not fall on the same point in each bucket.
Sample
Negative peak
Figure 20. Trace point saved in memory is based on detector type algorithm
Figure 21. Normal detection displays maximum values in buckets where the signal only rises or only falls
10
Input attenuator
Figure 23. Spectrum analyzer block diagram with gated video time-gating
Time gated spectral analysis permits analysis of the contents of the pulse without the effect of the envelope of the pulse itself. One way of performing time-gating is to place a gate (switch) in the video path of the spectrum analyzer as shown in Figure 23. This method of time-gating is called gated video.
11
www.agilent.com
Agilent Technologies Test and Measurement Support, Services, and Assistance Agilent Technologies aims to maximize the value you receive, while minimizing your risk and problems. We strive to ensure that you get the test and measurement capabilities you paid for and obtain the support you need. Our extensive support resources and services can help you choose the right Agilent products for your applications and apply them successfully. Every instrument and system we sell has a global warranty. Two concepts underlie Agilents overall support policy: Our Promise and Your Advantage. Our Promise Our Promise means your Agilent test and measurement equipment will meet its advertised performance and functionality. When you are choosing new equipment, we will help you with product information, including realistic performance specifications and practical recommendations from experienced test engineers. When you receive your new Agilent equipment, we can help verify that it works properly and help with initial product operation. Your Advantage Your Advantage means that Agilent offers a wide range of additional expert test and measurement services, which you can purchase according to your unique technical and business needs. Solve problems efficiently and gain a competitive edge by contracting with us for calibration, extra-cost upgrades, out-of-warranty repairs, and onsite education and training, as well as design, system integration, project management, and other professional engineering services. Experienced Agilent engineers and technicians worldwide can help you maximize your productivity, optimize the return on investment of your Agilent instruments and systems, and obtain dependable measurement accuracy for the life of those products.
Related Literature
Figure 25. Agilent PSA Series spectrum analyzer
Agilent Open
www.agilent.com/find/open Agilent Open simplifies the process of connecting and programming test systems to help engineers design, validate and manufacture electronic products. Agilent offers open connectivity for a broad range of system-ready instruments, open industry software, PC-standard I/O and global support, which are combined to more easily integrate test system development. For more information on Agilent Technologies products, applications or services, please contact your local Agilent office. Phone or Fax United States: (tel) 800 829 4444 (fax) 800 829 4433 Canada: (tel) 877 894 4414 (fax) 800 746 4866 China: (tel) 800 810 0189 (fax) 800 820 2816 Europe: (tel) 31 20 547 2111 Japan: (tel) (81) 426 56 7832 (fax) (81) 426 56 7840 Korea: (tel) (080) 769 0800 (fax) (080) 769 0900 Latin America: (tel) (305) 269 7500 Taiwan: (tel) 0800 047 866 (fax) 0800 286 331 Other Asia Pacific Countries: (tel) (65) 6375 8100 (fax) (65) 6755 0042 Email: tm_ap@agilent.com
Contacts revised: 05/27/05
Spectrum Analysis Basics, Application Note 150, literature number 5952-0292 Optimizing Spectrum Analyzer Measurement Speed, Application Note 1318, literature number 59683411E Optimizing Dynamic Range for Distortion Measurements, Product Note, literature number 5980-3079EN Optimizing Spectrum Analyzer Amplitude Accuracy, Application Note 1316, literature number 5968-3659E Selecting the Right Signal Analyzer for Your Needs, Selection Guide, literature number 5968-3413E PSA Series Swept and FFT Analysis, Product Note, literature number 5980-3081EN
The complete list is available at: www.agilent.com/find/contactus Product specifications and descriptions in this document subject to change without notice. Agilent Technologies, Inc. 1998, 2000, 2004, 2005 Printed in USA, July 27, 2005 5965-7009E
Web Resource
www.agilent.com/find/spectrumanalyzers