0 penilaian0% menganggap dokumen ini bermanfaat (0 suara)
48 tayangan13 halaman
The document describes the signaling flow and procedures involved in establishing a circuit-switched voice call between a UE and core network via a UTRAN/GERAN radio access network. It involves radio resource control messages between the UE and RNC to establish the radio connection and logical channels. Mobility management and call control messages are then exchanged via the RANAP and RRC protocols to perform authentication, security setup, RAB establishment and call setup. The call is established with AMR voice coding and resources allocated on the downlink and uplink for the voice and video bearer services.
The document describes the signaling flow and procedures involved in establishing a circuit-switched voice call between a UE and core network via a UTRAN/GERAN radio access network. It involves radio resource control messages between the UE and RNC to establish the radio connection and logical channels. Mobility management and call control messages are then exchanged via the RANAP and RRC protocols to perform authentication, security setup, RAB establishment and call setup. The call is established with AMR voice coding and resources allocated on the downlink and uplink for the voice and video bearer services.
The document describes the signaling flow and procedures involved in establishing a circuit-switched voice call between a UE and core network via a UTRAN/GERAN radio access network. It involves radio resource control messages between the UE and RNC to establish the radio connection and logical channels. Mobility management and call control messages are then exchanged via the RANAP and RRC protocols to perform authentication, security setup, RAB establishment and call setup. The call is established with AMR voice coding and resources allocated on the downlink and uplink for the voice and video bearer services.
NBAP: Radio Link Setup Request NBAP: Radio Link Setup Response ALCAP: ERQ (Establish Request) ALCAP: ECF (Establish Confirm) RRC: RRC Connection Setup (FACH) [RRCconnRepTimer1/2(100ms,1s)] L1 Synchronization NBAP: Synchronization Indication RRC: RRC Connection Setup Complete (DCH) RRC: Initial Direct Transfer (MM: CM Service Request) SCCP: CR (Connection Request) RANAP: Initial UE Message (MM: CM Service Request) SCCP: CC (Connection Confirm) RANAP: Direct Transfer (MM: Authentication Request) RRC: Downlink Direct Transfer (MM: Authentication Request) RRC: Uplink Direct Transfer (MM: Authentication Response) RANAP: Direct Transfer (MM: Authentication Response) RANAP: Common ID RANAP: Security Mode Command RRC: Security Mode Command FP: Downlink Synch FP: Uplink Synch RRC Connection Establishment CELL DCH State RNC checks if resources are available: BTS, AC, Transmission. If not it sends RRC Connection Reject T300=2s ; N300=3 L1 Synchronization T312=6s ; N312=4 MOS CS Message Flow UE RNC NodeB MGW/CN RRC: Security Mode Complete RANAP: Security Mode Complete RRC: Uplink Direct Transfer (CC: Setup) RANAP: Direct Transfer (CC: Setup) RANAP: Direct Transfer (CC: Call Proceeding) RRC: Downlink Direct Transfer (CC: Call Proceeding) RANAP: RAB Assignment Request NBAP: Radio Link Reconfiguration Prepare NBAP: Radio Link Reconfiguration Ready ALCAP: ERQ (Establish Request) ALCAP: ECF (Establish Confirm) NBAP: Radio Link Reconfiguration Commit) RRC: Radio Bearer Setup RRC: Radio Bearer Setup Complete RANAP: RAB Assignment Response ALCAP: ERQ (Establish Request) ALCAP: ECF (Establish Confirm) RAB Establishment FP: Downlink Synch FP: Uplink Synch RL modification procedure: SRB+DCH, HW resources checked Possible failure in AAL2 setup (Iub, Iur and Iu) Soft handover is not allowed during the RAB establishment procedure (The mobile can not add or remove cells in AS) this makes the UE and Node B particularly sensitive to mobility and dominance Timer wf_rb_setup_cpl (6s) is started when the RRC: Radio Bearer Setup message is sent to the UE In case the timer expires Iu Release Request is sent to the CN with release cause (radio_conn_lost) Call Established UE RNC NodeB RANAP: Direct Transfer (CC: Connect) RRC: Downlink Direct Transfer (CC: Connect) RRC: Uplink Direct Transfer (CC: Connect Acknowledge) RANAP: Direct Transfer (CC: Connect Acknowledge) RRC: Uplink Direct Transfer (CC: Release Complete) RANAP: Direct Transfer (CC: Release Complete) RANAP: Iu Release Command RRC: Uplink Direct Transfer (CC: Disconnect) RANAP: Direct Transfer (CC: Disconnect) RANAP: Direct Transfer (CC: Release) RRC: Downlink Direct Transfer (CC: Release) RANAP: Iu Release Complete MGW/CN RANAP: Location Report RRC: Measurement Control Call Disconnect RRC: Downlink Direct Transfer (CC: RRC Connection Release) RRC: Uplink Direct Transfer (CC: Release Complete) RRC: Uplink Direct Transfer (CC: Release Complete) NBAP: Radio Link Deletion Request NBAP: Radio Link Deletion Response ALCAP: ERQ (Establish Request) ALCAP: ECF (Establish Confirm) RANAP: Direct Transfer (CC: Alerting) RRC: Downlink Direct Transfer (CC: Alerting) UE RNC NodeB MGW/CN RRC: RRC Connection Request (RACH) NBAP: Radio Link Setup Request NBAP: Radio Link Setup Response ALCAP: ERQ (Establish Request) ALCAP: ECF (Establish Confirm) RRC: RRC Connection Setup (FACH) L1 Synchronization NBAP: Synchronization Indication RRC: RRC Connection Setup Complete (DCH) RRC: Initial Direct Transfer (MM: Paging Response) SCCP: CR (Connection Request) RANAP: Initial UE Message (MM: Paging Response) SCCP: CC (Connection Confirm) RANAP: Direct Transfer (MM: Authentication Request) RRC: Downlink Direct Transfer (MM: Authentication Request) RRC: Uplink Direct Transfer (MM: Authentication Response) RANAP: Direct Transfer (MM: Authentication Response) RANAP: Common ID RANAP: Security Mode Command RRC: Security Mode Command FP: Downlink Synch FP: Uplink Synch RRC Connection Establishment CELL DCH State L1 Synchronization MTC CS Message Flow RANAP: Paging RRC: Paging Type 1 UE RNC NodeB MGW/CN RRC: Security Mode Complete RANAP: Security Mode Complete RRC: Uplink Direct Transfer (CC: Setup) RANAP: Direct Transfer (CC: Setup) RANAP: Direct Transfer (CC: Call Confirmed) RRC: Downlink Direct Transfer (CC: Call Confirmed) RANAP: RAB Assignment Request NBAP: Radio Link Reconfiguration Prepare NBAP: Radio Link Reconfiguration Ready ALCAP: ERQ (Establish Request) ALCAP: ECF (Establish Confirm) NBAP: Radio Link Reconfiguration Commit) RRC: Radio Bearer Setup RRC: Radio Bearer Setup Complete RANAP: RAB Assignment Response ALCAP: ERQ (Establish Request) ALCAP: ECF (Establish Confirm) RAB Establishment FP: Downlink Synch FP: Uplink Synch RL modification procedure: SRB+DCH, HW resources checked Possible failure in AAL2 setup (Iub, Iur and Iu) Soft handover is not allowed during the RAB establishment procedure (The mobile can not add or remove cells in AS) this makes the UE and Node B particularly sensitive to mobility and dominance Timer wf_rb_setup_cpl (6s) is started when the RRC: Radio Bearer Setup message is sent to the UE In case the timer expires Iu Release Request is sent to the CN with release cause (radio_conn_lost) Call Established UE RNC NodeB RANAP: Direct Transfer (CC: Connect) RRC: Downlink Direct Transfer (CC: Connect) RRC: Uplink Direct Transfer (CC: Connect Acknowledge) RANAP: Direct Transfer (CC: Connect Acknowledge) MGW/CN RANAP: Location Report RRC: Measurement Control RANAP: Direct Transfer (CC: Alerting) RRC: Downlink Direct Transfer (CC: Alerting) MOC M T C MOC/MTC Call Flow timing RRC messages information Voice and Video are both Conversational Call RRC messages information DL SRB RRC messages information UE in DUAL MODE RRC messages information Voice AMR RRC messages information CS call, 64Kbps, Transparent
Video Call RRC messages information Video CS 64: DL SF 32 UL SF 16 Voice AMR: DL SF 128 UL SF 64