Fungsi
Menaikkan atau
memperbesar tekanan udara
atau gas yang akan dialirkan
dalam suatu ruangan tertentu
juga sebagai persiapan atau
pemvakuman udara atau gas
tertentu.
Untuk industri kimia dimana
penghisapan lebih besar dari
tekanan atmosphir untuk
sirkulasi udara pada proses
kimia disebut booster atau
circulator
2
Komponen Blower
Drive
Blower Lobes
Casing
Inlet Filter / Silencer
Inlet Port
Exhaust Port
Timing Gears
Shaft Support Bearings
Oil Bath Reservoir
Relief Valve
Bearing
Biasanya memakai journal type bearing.
Mempunyai babbit lined dengan alur untuk oli atau
juga pelumasan yang menggunakan tekanan.
Kadang-kadang memakai coller type thrust
bearing.
Casing :
Dibuat dari cast iron atau dibuat dari steel plate yang dilas
dengan diperkuat oleh pelat-pelat.
Prinsip Operasi
2 specially designed impellers
Prinsip Operasi
Gear & bearing lubrication occurs
10
Aplikasi
11
Aplikasi Blower
Blower : mempunyai tekanan sedang dan volume
: 10 150 KW
Transmisi
12
Aplikasi Blower
Fungsi : untuk mengangkat material serbuk di
13
Pemeliharaan Umum
-Menjaga kebersihan Insert Air Filter
-Menjaga Oil Level.
-Menjaga kebersihan lingkungan.
-Menjaga kelurusan dan tegangan V-Belt
-Mencegah kebocoran
14
Blower
Pulley V-Belt
15
Blower
16
Blower
17
Operasi Blower
Operasi blower adalah hampir sama dengan operasi
pompa, waktu menstart atau menstop haruslah dicek in
terlebih dahulu untuk mengurangi beban penggeraknya.
Tetapi hanya satu hal saja yang perlu diperhatikan selama
pengoperasian, yakni pengecekkan yang dilakukan
sesekali terhadap temperatur dan jumlah oil atau dapat
dilihat dari batas kerja / jam kerjanya.
18
Operasi Blower
Prosedur yang benar dalam men-start-up blower berkapasitas
atau orang (misalnya jika kita berdiri pas di sisi masukan) yang
tersedot masuk kedalam impellernya sehingga dapat
membahayakan kita atau merusak impeller .
19
Running Inspection
OK
20
Static Inspection
Blowers Static Inspection
Check For
Inspect the Blower drive motor for material build up on cooling fins and
cooling fan inlet screen. Remove build-up
Inspect drive motor electrical connections for damage or strain
Inspect the condition and support integrity of all safety guards
Inspect the drives mounting base for damage, cracks, loose bolts
Inspect the condition of the drive belts, check tensioning, sheaves, or drive
coupling
Verify the condition and operation of the relief valve on the blower. Ensure
that the relief valve operates freely and seats properly
Inspect the condition of the blower inlet filter and replace or clean as
necessary.
Verify the Blowers direction of rotation
Inspect the general condition of the equipment cleanliness, damage
Inspect Blower casing for wear, damage or in-leakage
Check that all access doors, inspection ports, and measurement ports are
closed and properly sealed
OK
21
Troubleshooting
Loss of airflow capacity
22
Troubleshooting
Problem
Knocking
Excessive
Blower
Temperature
Possible Cause
Unit out of time
Solution
Retime impellers
Worn gears
Worn bearings
Replace bearings
Remove obstruction
Internal contact
Replace impeller
Correct clearances
OK
23
Troubleshooting
Impeller End or
Tip Drag
Correct clearances
24
Troubleshooting
Lack of Volume
Excessive Bearing
or Gear Wear
Loss of Oil
Slipping belts
Tighten belts
Worn clearances
Drive failure
Re-adjust or replace
Improper lubrication
Worn seal
Replace seals
25
Safety
Always lock out Blower prior to performing any service
Casing temps may be extremely hot
Blowers controlled automatically - can start/stop at any time
Keep work area clear of grease, oil, water, etc that could cause a
slip or a fall
Keep clothing, fingers, hair, etc. away from drive components &
Blower inlet
26
Safety (contd)
27
Safety (contd)
Prolonged exposure may require ear protection
WARNING Dont exceed sheave or coupling manufacturers' rim
speed limit
Know location & function of all control stations
Keep all control stations free from obstructions to ensure access
at all times
Report all unsafe conditions or practices immediately
28
dengan kebutuhan
Sesuaikan tekanan sedekat mungkin dengan
29
30