Sebaik dan seteliti apapun seseorang menggunakan printer, lama kelamaan pasti akan mengalami kerusakan atau error, Hal ini pernah saya alami saat saya lagi baru masuk prakerin disebuah toko yang melayani service printer, untung saja ada si bos yang mengajari saya cara reset printer canon MP237, sebelum memasuki topik persiapkan terlebih dahulu persyaratannya yaitu sobat harus mempunyai software resetter-nya, kalo belum punya silahkan Download Disini
Nama software untuk reset printer canon MP237 adalah Canon Resetter Service Tool V3400, software ini tidak hanya dapat digunakan untuk reset printer canon MP237 tetapi bisa digunakan untuk reset pinter canon MG5270,MP258, MP287, MP278, MP237 dan IP 2770. Nah sekarang kita memasuki topik, untuk mengatasi masalah seperti error E08 pada printer yang telah saya sebutkan di atas, sobat bisa baca uraian dibawah ini : 1. Hidupkan printer terlebih dahulu, pada layar monior akan muncul error E08, dan ada keterangan"The Ink Absorber is Almost Full" 2. Jadikan Printer dalam keadaan Service Mode, Caranya berikut ini : Matikan printer yang error E08 dengan menekan tombol power, (pastikan kabel power printer masih menempel pada printer) Tekan tombol RESET yang di ikuti dengan menekan tombol POWER, (kedua tombol dalam keadaan tertekan). Kemuadian lepas tombol RESET tapi jangan lepas tombol POWER. dalam keadaan tombol POWER tertekan tombol RESET sebanyak 6X . lalu lepaskan kedua tombol bersamaan Monitor komputer sobat akan mengalami blank/gelap dan komputer sobat akan mendeteksi device baru (bisa diabaikan) Cara menjalankan Canon Resetter Service Tool V3400 Pasang kertas terlebih dahulu Jalankan software Canon Resetter Service Tool V3400 Di menu "absorber clear ink counter" pilih "MAIN" lalu klik set disebelah kanannya Di menu "ink absorbe counter" pilih "MAIN" lalu klik set disebelah kanannya Kemudian klik "EEPROM" maka printer akan malakukan cetak 1 kali Selesai, Silahkan Dicoba. Sekian, Semoga bermanfaat Maskakung Error Codes and Solution for Canon iP and MP Series 22 Juni 2011abu zulfaTinggalkan KomentarGo to comments These are list of Canon Pixma printer error codes and possible solution. Applicable for Canon Pixma Inkjet Printer IP and MP Series. These error codes mean machine problems. In many cases, the machine will require service. Canon Pixma Error Codes are indicated by the number of cycles of Alarm and Power LEDs blink, and the corresponding error code with the message Printer error has occurred. Turn off power then back on again. If problem persists, see the manual. is displayed on the LCD. Carriage error or Error Code 5100 Condition: An error occurred in the carriage encoder signal. Problems and Solutions: Smearing or scratches on the carriage slit film - clean the timing slit film. Foreign material or paper debris that obstructs the carriage movement; - remove foreign material. Ink tank conditions; - re-seat the ink tanks. If other solution fail, replace one off the following - Timing slit disk film - Carriage unit - Logic board - Carriage motor Line Feed error or Error Code 6000 Condition: An error occurred in the LF encoder signal. Problems and Solutions: Smearing or scratches on the LF / EJ slit film - clean the LF / EJ slit film. Foreign material or paper debris in the LF drive; - remove foreign material. If other solution fail, replace one off the following - LF / EJ slit film - LF / EJ timing sensor unit - Paper feed roller unit - Logic board - Paper feed motor Purge cam sensor error or Error Code 5C00 Condition: An error occurred in the purge unit. Problems and Solutions: Foreign material or paper debris around the purge drive system unit; - remove foreign material. If other solution fail, replace one off the following - Purge drive system unit - Logic board ASF sensor error or Error Code 5700 Condition: An error occurred in the ASF cam sensor. Problems and Solutions: Replace one of the following: - ASF unit - PE sensor board unit - Logic board Internal temperature error or Error Code 5400 Condition: The internal temperature is not normal. Problems and Solutions: Replace one of the following: - Carriage unit - Logic board - Print head Ink absorber is full or Error Code 5B00, 5B01 Condition: The ink absorber is supposed to be full. Message on the Monitor screen or printer LCD: Ink absorber full. Service required. Problems and Solutions: Ink absorber is full or waste pad inside the printer is almost full - Replace printers Ink absorber pad and reset the ink absorber counter value in the EEPROM. Print head temperature rise error or Error Code 5200 Condition: The print head temperature exceeded the specified value. Problems and Solutions: Turn off the printer and then turn on if error still persist replace Ink cartridge or print head EEPROM error or Error Code 6800, 6801 Condition: A problem occurred in reading from or writing to the EEPROM. Problems and Solutions: Replace logic board VH monitor error or Error Code B200 Condition: The print head voltage is abnormal. Problems and Solutions: Replace Print head and logic board (Replace them at the same time.) Replace Power supply unit Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Carriage lift mechanism error or Error Code 5110 Condition: The carriage did not move up or down properly. Problems and Solutions: Foreign material or paper debris that obstructs the carriage movement - remove foreign material. Consider replacing: - Switch system unit - Carriage unit APP position error or Error Code 6A80 Condition: An error occurred in the APP motor. Problems and Solutions: Check for foreign material or paper debris around the purge drive system unit - remove foreign material. Check for foreign material or paper debris around the ASF unit - remove foreign material. If other solution fail, replace one off the following part - Purge drive system unit - Logic board APP sensor error or Error Code 6A90 Condition: An error occurred during paper feeding or purging. Problems and Solutions: check for foreign material or paper debris around the purge drive system unit; - remove foreign material. check for foreign material or paper debris around the ASF unit; - remove foreign material. If other solution fail, replace one off the following part - Purge drive system unit - Logic board Paper feed cam sensor error or Error Code 6B10 Condition: An error occurred in the paper feed cam sensor during paper feeding from the cassette, or the paper absorbing a large amount of ink jammed in the PF rear guide. Problems and Solutions: Jammed paper in the PF rear guide (when a large amount of ink was absorbed in the paper); - remove the jammed paper and foreign material. check for foreign material or paper debris in the cassette or in the PF rear guide; - remove foreign material. If other solution fail, replace one off the following part - PF pick-up unit - Logic board USB Host VBUS overcurrent or Error Code 9000 Condition: The USB Host VBUS is overloaded. Problems and Solutions: Replace Logic board Pump roller sensor error or Error Code 5C20 Condition: The pump roller position cannot be detected. Problems and Solutions: Replace Purge drive system unit Ink tank position sensor error or Error Code 6502 Condition: None of the ink tank position is detected. Problems and Solutions: check Ink tank position Re-seat or replacement of ink tanks Replace parts - Spur unit - Logic board Flatbed motor error or Error Code 5012 Condition: An error occurred in the scanner flatbed motor. Problems and Solutions: replace Scanner unit Valve cam sensor error or Error Code 6C10 Condition: The valve cam sensor was faulty at power-on or when purging was attempted. Problems and Solutions: check for foreign material or paper debris around the purge drive system unit; - remove foreign material. Replace - Purge drive system unit - Logic board
Cara Memperbaiki Error E08 pada printer Canon MP 237
Kemarin salah seorang Pelanggan Kami baru membeli Printer dengan merek dan tipenya adalah Canon Pixma MP 237, berarti sudah saatnya Saya menuliskan di blog ini cara untuk perawatan dan perbaikannya, supaya nanti di kemudian hari apabila terjadi error E08 pada printer tersebut, pelanggan kami bisa membacanya disini. langsung saja ya, cara mengatasi Error E08 pada printer Canon MP 237 adalah sebagai berikut :
Berikut adalah cara mengatasi Error E08 pada printer Canon MP 237
1. Hidupkan Printer, maka di panel LCD akan muncul error E08, dan ada keterangan "The Ink Absorber is Almost Full" pada layar monitor. 2. Download Resetter Canon Service Tool v3400 disini atau bisa juga di link yang ada diakhir tulisan ini. 3. Printer harus dalam keadaan Service Mode. Caranya berikut ini 4. Matikan Printer yang error E08 dengan menekan tombol POWER. Jangan cabut kabel power. 5. Tekan dan Tahan tombol STOP/RESET diikuti dengan menekan Tombol POWER. Jadi kedua tombol posisi tertekan. 6. Lepas tombol STOP/RESET tapi jangan lepas tombol POWER. 7. Dalam keadaan tombol POWER masih tertekan, tekan tombol STOP/RESET sebanyak 6 kali. 8. Kemudian lepaskan kedua tombol bersamaan. Maka Printer akan berada dalam kondisi Service Mode. 9. Dan di komputer Anda akan mendeteksi hardware baru. Abaikan saja. 10. Langkah selanjutnya Exctract dan Jalankan Service Tool v3400 yang sobat download tadi. 11. Di menu absorber clear ink counter pilih Main kemudian klik SET di sebelah kanannya. 12. Di menu ink absorber counter pilih Main kemudian klik SET di sebelah kanannya. 13. Kemudian klik EEPROM. maka printer akan cetak 1 halaman. 14. Selesai dan Printer Canon akan normal kembali.
Kode Error Printer Canon MP 237 Serta Cara Mengatasi dan Memperbaiki Canon MP 237 Posted by Bernadus Tri Ardi Monday, April 8, 2013 7 comments Kode Error Printer Canon MP 237, Canon MP 237 jika mengalami kesalahan maka akan diberitahu dengan lampu alarm LED bekedip/blinking orange dan menampilkan kode error printer di LCD monitor Komputer sehingga Printer Canon MP 237 tidak dapat mencetak data.
Kode Error Canon MP 237 biasa muncul dengan angka seperti 1300, 5011, 5100 dan menyebabkan printer Canon MP 237 tidak dapat mencetak data. Kode Error Canon MP 237 biasanya disebabkan karena Paper Jammed, Printer is out of paper, The FINE cartridge cannot be recognized dan masih banyak lagi.
Berikut ini Kode Error Canon MP 237 dan Cara Mengatasi Kesalahan dengan Kode Error Canon MP 237 : 1. Error 1000 Canon MP 237 : Printer is out of paper / paper does not feed, Ditandai dengan blinking 2x pada Canon MP 237 dan untuk mengatasinya masukkan kertas ke bagian rear tray kemudian tekan tombol Hitam/warna pada Printer 2. Error 1300 Canon MP 237 : Paper Jammed, ditandai dengan blinking 3x pada Canon MP 237 dan cara mengatasinya ambil kertas yang menyangkut pada printer. 3. Error 1687 Canon MP 237 : The FINE Cartridge is not installed properly, ditandai blinking 4x pada Printer canon MP 237 dan cara mengatasinya, pastikan pemasangan cartridge sudah benar dan mengunci cartridge. 4. Error 1401, 1403, 1485 Canon MP 237 : The FINE Cartridge is not installed properly,disertai blinking 5x dan cara mengatasinya adalah pasang cartridge dengan benar jika masih terjadi ganti cartridge dengan yang baru. 5. Error 1486, 1487 Canon MP 237 : FINE Cartridge is not installed in the correct position,disertai dengan blinking 7x dan cara mengatasinya adalah pastikan pemasangan cartridge sudah benar jika masih terjadi coba ganti dengan cartridge baru. 6. Error 1700 Canon MP 237 : Ink absorber is almost full, disertai blinking 8x dan cara mengatasinya adalah lakukanlah head cleaning pada printer Canon MP 237. 7. Error 1686 Canon MP 237 : The remaining ink level cannot be detected, disertai blinking 13x karena printer tidak bisa mendeteksi level tinta, tekan tombol stop/reset selama 5 detik untuk mengabaikan error. 8. Error 1684 Canon MP 237 : The FINE cartridge cannot be recognized, disertai blinking 14x karena cartridge tidak terpasang dengan benar atau cartridge tidak kompatibel dengan printer, ganti cartridge denga yang baru. 9. Error 1682 Canon MP 237 : The FINE cartridge cannot be recognized, disertai blinking 15x dan cara mengatasinya adalah ganti dengan cartridge baru karena catridge lama sudah rusak. 10. Error 1688 Canon MP 237 : The ink has run out, disertai dengan blinking 16x dan cara mengatasinya tekan tombol stop/reset selama 5 detik. 11. Error 5100 Canon MP 237 : Paper Jammed disertai blinking 2x dan cara mengatasinya bersihkan kertas menyangkut pada printer. 12. Error B200 Canon MP 237 : Blinking 10x, Matikan Printer kemudian cabut kabel power yang menyambung ke listrik selama beberapa menit kemudian pasang dan nyalakan kembali. Beberapa Kode error pada printer canon MP 237 antara lain 5011, 5012, 5200, 5400, 5700, 6000, 6800, 6801, 5B00, 6930, 6931, 6932, 6933, 6936, 6937, 6938, 6940, 6941, 6942, 6943, 6944, 6945, 6946 dan cara mengatasinya adalah dengan mencabut kabel power printer yang menyambung ke listrik selama beberapa menit kemudian nyalakan kembali, Jika masalah masih belum teratasi silahkan membawa printer tersebut ke Service Center Canon.